Clarion CD Player DXZ866MP User Manual

Owner’s manual  
DXZ866MP  
CD/MP3/WMA Receiver / CeNET & Touch Panel Control  
CD/MP3/WMA接收器/ CeNET及触控面板控制  
CD/MP3/WMA 리시버 / CeNET & 터치패널 컨트롤  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. PRECAUTIONS  
1. When the inside of the car is very cold and  
the player is used soon after switching on the  
heater, moisture may form on the disc or the  
optical parts of the player and proper  
2. Driving on extremely bumpy roads may  
cause severe vibration and cause the sound  
to skip.  
3. This unit uses a precision mechanism. Even  
in the event that trouble arises, never open  
the case, disassemble the unit, or lubricate  
the rotating parts.  
playback may not be possible. If moisture  
forms on the disc, wipe it off with a soft cloth.  
If moisture forms on the optical parts of the  
player, do not use the player for about 1 hour.  
The condensation will disappear naturally  
allowing normal operation.  
WARNING  
For your safety, do not watch or operate the touch panel while driving.  
CAUTION  
USE OF CONTROLS, ADJUSTMENTS, OR  
PERFORMANCE OF PROCEDURES OTHER  
THAN THOSE SPECIFIED HEREIN, MAY  
RESULT IN HAZARDOUS RADIATION  
EXPOSURE.  
THE COMPACT DISC PLAYER AND MINI DISC  
PLAYER SHOULD NOT BE ADJUSTED OR  
REPAIRED BY ANYONE EXCEPT PROPERLY  
QUALIFIED SERVICE PERSONNEL.  
CHANGES OR MODIFICATIONS NOT  
EXPRESSLY APPROVED BY THE  
MANUFACTURER FOR COMPLIANCE COULD  
VOID THE USER’S AUTHORITY TO OPERATE  
THE EQUIPMENT.  
INFORMATION FOR USERS:.  
CHANGES OR MODIFICATIONS TO THIS  
PRODUCT NOT APPROVED BY THE  
MANUFACTURER WILL VOID THE  
WARRANTY.  
DXZ866MP  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sloping Console  
This unit uses a SLOPING CONSOLE to make  
large screen displays possible.  
2. Before the SLOPING CONSOLE closes,  
there may be a braking sound from the safety  
mechanism. This is normal.  
When you use the SLOPING CONSOLE, be  
sure to close it.  
3. If you move the SLOPING CONSOLE by  
hand, this may start play. To correct this play,  
with the power for the unit ON, press the [Q]  
button to close the SLOPING CONSOLE.  
CAUTION  
4. After a disc is ejected, the SLOPING  
CONSOLE automatically returns to the tilted  
or closed state. If there is any obstruction  
when the SLOPING CONSOLE tries to close,  
the safety mechanism is triggered and the  
SLOPING CONSOLE returns to the open  
state. If this happens, remove the  
obstruction, then press the [Q] button.  
5. To avoid scratching the compact disc, keep  
the 12 or 8 cm CD level when loading or  
removing it.  
BE CAREFUL NOT TO GET YOUR FINGERS  
CAUGHT WHEN OPENING AND CLOSING  
THE SLOPING CONSOLE.  
1. For safety’s sake, always close the SLOPING  
CONSOLE before leaving this unit unused for  
a prolonged period or switching OFF the  
ignition key.  
If you switch OFF the ignition key with the  
SLOPING CONSOLE tilted, the SLOPING  
CONSOLE does not close.  
Handling Compact Discs  
• Do not use compact discs that have large  
scratches, are misshapen, cracked, etc. Use of  
such discs may cause misoperation or  
damage.  
To remove a compact disc from its storage  
case, press down on the center of the case  
and lift the disc out, holding it carefully by the  
edges.  
Use only compact discs bearing the  
mark.  
or  
Do not play heart-shaped, octagonal, or other  
specially shaped compact discs.  
Some CDs recorded in the CD-R/CD-RW mode  
may not be usable.  
• Do not use commercially available CD  
protection sheets or discs equipped with  
stabilizers, etc. These may damage the disc or  
break the internal mechanism.  
Handling  
• Compared to ordinary music CDs, CD-R and  
CD-RW discs are both easily affected by high  
temperature and humidity and some CD-R and  
CD-RW discs may not be playable. Therefore,  
do not leave them for a long time in the car.  
• New discs may  
have some  
roughness  
around the  
edges. If such discs  
Storage  
• Do not expose compact discs to direct sunlight  
or any heat source.  
• Do not expose compact discs to excess  
humidity or dust.  
• Do not expose compact discs to direct heat  
from heaters.  
Ball-point pen  
Roughness  
are used, the player  
may not work or the sound  
Cleaning  
To remove fingermarks and dust, use a soft  
cloth and wipe in a straight line from the center  
of the compact disc to the circumference.  
• Do not use any solvents, such as commercially  
available cleaners, anti-static spray, or thinner  
to clean compact discs.  
may skip. Use a ball-point pen  
or the like to remove any  
roughness from the edge of the disc.  
• Never stick labels on the surface of the  
compact disc or mark the surface with a pencil  
or pen.  
• After using special compact disc cleaner, let  
the compact disc dry off well before playing it.  
• Never play a compact disc with any cellophane  
tape or other glue on it or with peeling off  
marks. If you try to play such a compact disc,  
you may not be able to remove it from the CD  
player or it may damage the CD player.  
4
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. CONTROLS  
Source unit  
[
]
[Q] (OPEN/EJECT)  
ADJ  
Photo Sensor  
IR-Receiver  
[MODE]  
[
]
ROTARY  
[
] (SOUND)  
[SRC]  
[ISR]  
Display  
With the SLOPING CONSOLE opened  
[CD SLOT]  
DCP Detaching Slider  
DXZ866MP  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. NOMENCLATURE  
Names of the Buttons and their Functions  
IR-Receiver  
[ROTARY] knob  
• Receiver for remote control unit. (Operating  
range: 30° in all directions)  
• Press the knob to turn the power ON.  
• Press the knob to turn the power OFF.  
• Turn the knob to adjust the volume.  
[ADJ] button  
• Use this button to set or adjust the various  
settings in the adjust mode.  
[CD SLOT]  
• CD insertion slot.  
[Q] (OPEN/EJECT) button  
DCP Detaching Slider  
• Removes the DCP.  
• Open/closes the control panel.  
To eject a disc, open the control panel first, and  
then press this button once again.  
Display  
• Displays the various information that indicates  
the operating state of this unit such as tuning/  
play state and indicators.  
• You can operate the display by touching or  
touching  
Photo Sensor  
• This sensor detects the brightness inside your  
car. When the auto-dimmer function is set to  
AUTO”, the brightness of the display is  
dimmed according to the brightness detected  
by this sensor.  
the surface. (cf. page 9)  
[MODE] button  
• Use this button to play in scan, repeat, or  
random mode.  
• Press and hold this button for 2 seconds or  
longer to switch between standard and simple  
operation displays.  
[
] (SOUND) button  
• Use this button for setting or adjusting various  
settings such as ADF.  
[ISR] (Instant Station Recall) button  
• Immediately calls up a favorite radio station  
regardless of the current mode. (This is the  
ISR function.) You can store radio stations to  
the [ISR] button by holding this button down for  
2 seconds or longer in the radio mode.  
[SRC] button  
• Switches among sound sources as shown  
below.  
Radio CD/MP3 (CD changer) ➜  
(DVD changer) (TV) AUX Radio...  
Note:  
External equipment not connected with CeNET is  
not displayed.  
6
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operations when External Equipment is Connected to this Unit  
When the CD/DVD changer is  
connected  
For details, see the section “CD changer  
operations” (cf. page 35). For the DVD  
changer, refer to the Owner’s Manual  
provided with the DVD changer.  
When the TV is connected  
For details, see the section “TV  
operations” (cf. page 38).  
DXZ866MP  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Touch Panel Buttons  
Standard operation display  
Simple operation display  
(To switch to the simple operation display, press  
and hold the [MODE] button for 2 seconds or  
longer.)  
Left slide  
button  
Right slide  
button  
Left button  
Right button  
98.10  
P3  
FM1  
P.CH  
SEEK  
pm  
2:45  
DISP  
PRESET  
BAND  
PS/AS  
FM1  
P.CH  
SEEK  
pm  
2:45  
DISP  
P3  
98.10  
Sub buttons  
PRESET  
BAND  
PS/AS  
Sub buttons  
Left slide button  
Touch this button for seek up/down or track up/  
down operations.  
Touch and hold this button for fast-forward/fast-  
rewind operations.  
Left button  
Touch this button for seek down or track down  
operations.  
Touch and hold this button for fast-rewind  
operation.  
Right slide button  
Touch this button for preset channel up/down,  
folder up/down, and disc up/down operations.  
Right button  
Touch this button for seek up or track up  
operations.  
Touch and hold this button for fast-forward  
operation.  
Sub buttons  
• Shows functions available in a certain context.  
Sub buttons  
• Shows functions available in a certain context.  
8
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Touch Panel Operations  
A touch panel display is used as the display on  
this unit. You can operate this display just by  
touching it with your fingertip. There are four  
main display operations as follows:  
Touch  
Touch the display with your fingertip, and move  
your finger to the up ( ) or down ( ) with your  
fingertip still touching the display, and keep your  
fingertip on the display. The current operation  
continues for the time your fingertip is held on  
the display. This operation is used, for example,  
for fast-forwarding/fast-rewinding tracks.  
Touch  
Touch the display with your fingertip and take it  
away within 1 second. This is the most basic  
operation when operating the display.  
Touch and hold  
Touch the display with your fingertip and hold it  
on the display for 1 or 2 seconds or longer. Do  
not move your finger while you are touching the  
display.  
Touch  
P
FM1  
Touch the display with your fingertip, and move  
your finger to the up ( ) or down ( ) with your  
fingertip still touching the display, and take your  
fingertip away within 1 second. This operation is  
used, for example, selecting tracks or discs.  
P.CH  
pm  
2:45  
DISP  
98.10  
MANU  
DXZ866MP  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. DCP  
The control panel can be detached to prevent  
theft. When detaching the control panel, store it  
in the DCP (DETACHABLE CONTROL PANEL)  
case to prevent scratches.  
Attaching the DCP  
1. Place the DCP to the SLOPING CONSOLE,  
adjusting the metal connecters on DCP and  
the SLOPING CONSOLE.  
We recommend taking the DCP with you when  
leaving the car.  
2. Press the DCP until it clicks into the  
SLOPING CONSOLE.  
Removing the DCP  
1. Press the [Q] button to open the DCP.  
2. Move the DCP detaching slider to the  
RELEASE” side.  
* The DCP display lights and is ready to use.  
3. Push and slide the DCP upward to remove.  
CAUTION  
• If the slider is on the [RELEASE] side and  
the DCP is not locked into place, it may fall  
out from vibration of the car. This can break  
the DCP, so after removing it, either firmly  
reattach it on the unit or put it in its DCP  
case.  
• The connector connecting the unit and the  
DCP is an extremely important part. Be  
careful not to damage it by pressing on it  
with fingernails, screwdrivers, etc.  
The SLOPING CONSOLE without DCP  
closes automatically in a few seconds.  
Note:  
• If the DCP is dirty, wipe off the dirt with a soft, dry  
cloth only.  
CAUTION  
• Do not try to remove or attach while  
driving.  
• The DCP can easily be damaged by shocks.  
After removing it, be careful not to drop it  
or subject it to strong shocks.  
• If you purchased a replacement DCP, an  
electrical adjustment is necessary.  
This adjustment requires technical  
knowledge.  
Please consult Clarion service or a Clarion  
service station.  
10  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. REMOTE CONTROL  
Receiver for remote control unit  
Operating range : 30° in all directions  
Signal transmitter  
Remote control unit  
[
]
]
[
[
]
SRC  
BND  
]
[
[
], [  
[
[
], [  
]
a
d
]
]
]
MUTE  
DISP  
[
ISR  
[
[
]
RDM  
]
RPT  
[
]
SCN  
Inserting the Battery  
1. Turn over the remote control unit and slide the  
cover in the direction indicated by the arrow in the  
illustration.  
2. Insert the battery (CR2025) into the insertion  
guides, with the printed side (+) facing upwards.  
3. Press the battery in the direction indicated by the  
arrow so that it slides into the compartment.  
1
4. Replace the cover and slide in until it clicks into  
place.  
Insertion guide  
3
Notes:  
Misuse may result in rupture of the battery, producing  
leakage of fluid and resulting in personal injury or damage  
to surrounding materials. Always follow these safety  
precautions:  
2
R
• Use only the designated battery .  
• When replacing the battery, insert properly, with +/-  
polarities oriented correctly.  
• Do not subject battery to heat, or dispose of in fire or  
water. Do not attempt to disassemble the battery.  
• Dispose of used batteries properly.  
DXZ866MP  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Functions of the Remote Control Unit Buttons  
Mode  
CD changer  
DVD changer  
Radio  
TV  
CD/MP3/WMA  
Button  
Switches among radio, CD/MP3/WMA, CD changer, DVD changer, TV and AUX.  
[SRC]  
Returns to the first  
track.  
Moves the next disc  
in increasing order.  
Switches reception  
band.  
Switches reception  
band.  
[BND]  
Increases and decreases volume (in all modes).  
[
[
] , [  
] , [  
]
]
Moves preset  
channels up and  
down.  
Moves tracks up and down.  
When pressed and held for 1 second or longer:  
Fast-forward/fast-rewind.  
Moves preset  
channels up and  
down.  
No function.  
Switches between playback and pause.  
[
]
No function.  
Turns mute on and off.  
[MUTE]  
[ISR]  
Recalls ISR radio station in memory.  
When pressed and held for 2 seconds or longer: Stores current station into ISR memory (radio  
mode only).  
[DISP]  
[SCN]  
Switches between the title display and the spectrum analyzer display.  
Scan play.  
Preset scan.  
Preset scan.  
Scan play.  
When pressed and  
held for 1 second or  
longer:  
Folder scan play  
(MP3/WMA disc).  
When pressed and  
held for 2 seconds or  
longer:  
When pressed and  
held for 2 seconds or  
longer:  
When pressed and  
held for 1 second or  
longer:  
Auto store.  
Auto store.  
Disc scan play.  
No function.  
[RPT]  
Repeat play.  
No function.  
Repeat play.  
When pressed and  
held for 1 second or  
longer:  
When pressed and  
held for 1 second or  
longer:  
Folder repeat play  
(MP3/WMA disc).  
Disc repeat play.  
Switches between TV  
and VTR.  
[RDM]  
Random play.  
No function.  
Random play.  
When pressed and  
held for 1 second or  
longer:  
When pressed and  
held for 1 second or  
longer:  
Folder random play  
(MP3/WMA disc).  
Disc random play.  
Some of the corresponding buttons on the source unit and remote control unit have different functions.  
12  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. OPERATIONS  
Basic Operations  
CAUTION  
Selecting a mode  
1. Press the [SRC] button to change the  
Be sure to lower the volume before  
operation mode.  
switching the unit off or the ignition key. The  
unit remembers its last volume setting. If you  
switch the power OFF with the volume up,  
when you switch the power back ON, the  
sudden loud volume may hurt your hearing  
and damage the unit.  
2. Each time you press the [SRC] button, the  
operation mode changes in the following  
order:  
Radio CD/MP3 (CD changer) ➜  
(DVD changer) (TV) AUX Radio...  
External equipment not connected with  
CeNET is not displayed.  
Turning ON/OFF the power  
Turning on  
Note:  
• Be careful when using this unit for a long time  
without running the engine. If you drain the car’s  
battery too far, you may not be able to start the  
engine and this can reduce the service life of the  
battery.  
Adjusting the volume  
1. Turning the [ROTARY] knob clockwise  
increases the volume; turning it  
counterclockwise decreases the volume.  
The volume level is from 0 (minimum) to  
33 (maximum).  
1. Press the [ROTARY] knob.  
The mode that was previously active is  
displayed.  
Switching the operation  
display mode  
Turning off  
1. Press the [ROTARY] knob.  
The clock will stay displayed after the  
power is turned OFF.  
There are 2 basic operation displays: standard  
operation display and simple operation display.  
1. Press and hold the [MODE] button for 2  
seconds or longer to switch the operation  
display.  
To turn off the clock display  
Touch the clock to turn off the clock display  
while the power is off.  
FM1  
P.CH  
SEEK  
98.10  
pm  
2:45  
DISP  
P3  
PRESET  
BAND  
PS/AS  
CODEMATIC function  
In the simple operation display, the operations of  
touching in the radio or CD mode display  
screen are not required.  
When “CODEMATIC” is set to “ON”, and the  
power is turned ON with the DCP attached, the  
Touch Code display appears. Touch the display  
in the order that was set in the adjust mode.  
Descriptions given in this manual are mainly for  
the standard operation display. For descriptions  
for operations in the simple operation display,  
refer to the descriptions for the screen displays  
in the radio mode or the CD mode.  
ADJ SETTING  
CODEMATIC  
OFF  
RTN  
For details on the CODEMATIC function, see  
Using the security function” (cf. page 34).  
DXZ866MP  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
3. Touch  
on the left of the display to  
Switching the background  
1. Touch [DISP].  
select [DAY] or [NIGHT].  
COLOR SELECT  
NIGHT  
DARK BLUE  
98.10  
P3  
FM1  
P.CH  
SEEK  
RTN  
pm  
2:45  
DISP  
PRESET  
BAND  
PS/AS  
4. Touch  
select the color to set.  
COLOR  
• DARK BLUE  
on the right of the display to  
DISPLAY EDIT screen displays.  
2. Touch  
on the left of the display to  
choose the background.  
DISPLAY EDIT  
• IVORY  
P
02  
• WINE RED  
BGV  
• LIGHT BLUE  
• GREEN  
RTN  
SP/ANA  
The background includes 12 wallpaper  
images and 2 motion pictures.  
Choose [SCAN] to automatically display all  
the wallpaper.  
Adjusting the spectrum  
analyzer  
Background  
M01: WRC  
1. Touch [DISP].  
M02: Landscape  
P01: Car and Checker Flag  
P02: 307WRC from Two View Points  
P03: Rally Driver  
Don ,  
t
Stop Be  
01  
TRACK  
pm  
01:01  
2:45  
DISP  
TOP  
P04: Driving Scene  
P05: Cube  
P06: Bubble  
Display edit mode appears.  
2. Touch [SP/ANA].  
DISPLAY EDIT  
P07: Speaker  
P08: Digital Image1 (Disc media)  
<<  
TITLE  
P
05  
BGV  
P09: Digital Image2 (Broadcast media such  
D
-
BLUE  
as satellite)  
INPUT  
RTN  
SP/ANA  
COLOR  
P10: Mixer  
P11: Record Player  
P12: Meter  
The display shows the spectrum analyzer  
mode.  
3. Touch  
on the right of the display to  
3. Touch [RTN].  
select the spectrum analyzer to set.  
DISPLAY EDIT  
To change wallpaper color  
You can change the colors of the wallpaper  
(from P05 to P12).  
P
05  
1
BGV  
SPE/ANA  
D-BLUE  
COLOR  
MID  
TITLE  
SENS  
RTN  
• It can be set to both “DAY” mode and “NIGHT”  
mode.  
You can choose from four types.  
• When [SCAN] is selected, each of them is  
1. Touch [DISP].  
2. Touch [COLOR].  
DISPLAY EDIT  
displayed for about 10 seconds.  
4. Touch [SENS] to select the sensitivity.  
DISPLAY EDIT  
<<  
TITLE  
P
05  
BGV  
P
05  
1
D
-
BLUE  
AUTO  
BGV  
SPE/ANA  
D-BLUE  
COLOR  
LOW  
SCROLL  
RTN  
SP/ANA  
COLOR  
TITLE  
SENS  
RTN  
The [COLOR] is displayed only when you  
choose wallpaper from P05 to P12.  
You can choose from [HIGH], [MID], or [LOW].  
5. Touch [RTN].  
14  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
Switching the title display  
You can display stored information such as disc  
titles or track titles when playing back music in  
CD or CD changer mode.  
1. Touch [DISP] while a title is shown.  
01  
TRACK  
pm  
2:45  
DISP  
02:53  
TOP  
Display edit mode appears.  
2. Touch [TITLE].  
DISPLAY EDIT  
P
05  
1
BGV  
SPE/ANA  
D-BLUE  
COLOR  
LOW  
TITLE  
SENS  
RTN  
Title edit mode appears.  
3. Touch  
on the right of the display to  
choose the kind of title to show.  
DISPLAY EDIT  
<<  
TITLE  
P
05  
TRACK  
BGV  
D
-BLUE  
AUTO  
RTN  
SP/ANA  
COLOR  
SCROLL  
The title you have chosen is displayed. If it  
is too long to fit into the display, it  
automatically scrolls.  
4. Touch [SCROLL].  
• Select [AUTO] to scroll the title repeatedly.  
• Select [ONCE] to scroll the title only once.  
Notes:  
You cannot set the scroll options in User title  
mode.  
5. Touch [RTN].  
CD mode (MP3/WMA)  
Folder title (when using a folder) Play  
list (when using a play list) Track title  
Album TAG Artist TAG Title TAG ➜  
Folder title (when using a folder)...  
Notes:  
• MP3 supports ID3 Tags V2.3 / 2.2 / 1.1 / 1.0.  
Tag displays give priority to V2.3 / 2.2.  
• In the case of album Tags for WMA, the  
information written into the extension header is  
displayed.  
• Only ASCII characters can be displayed in Tags.  
DXZ866MP  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Operations  
BAND  
Screen displays in the radio  
mode  
Standard operation display  
The standard operation display appears by  
pressing the [SRC] button and selecting the  
radio mode.  
Touching this switches the reception band.  
Touching and holding this for 1 second or longer  
switches between the manual tuning mode and  
the seek tuning mode.  
PS/AS  
Touching this starts a preset scan.  
Touching and holding this for 2 seconds or  
longer starts an auto store.  
Touching this during the preset scan/auto scan  
ends the operation.  
Preset No.  
display  
Title display  
Reception  
Frequency  
display  
band display  
DISP  
The display contents can be changed.  
98.10  
P3  
FM1  
P.CH  
SEEK  
pm  
2:45  
DISP  
a/d (only in the simple operation display)  
Touching these enables seek tuning or step  
tuning (in the manual tuning mode).  
Touching and holding these enables quick  
tuning (in the manual tuning mode).  
PRESET  
BAND  
PS/AS  
DISP  
PRESET  
SEEK/MANU  
display  
PS/AS  
BAND  
Simple operation display  
Listening to the radio  
1. Press the [SRC] button to select the radio  
mode.  
Pressing and holding the [MODE] button for 2  
seconds or longer switches the simple operation  
display.  
Each press of the [SRC] button switches the  
mode as follows:  
a/d  
Radio CD/MP3 (CD Changer) ➜  
(DVD Changer) (TV) AUX Radio...  
FM1  
P.CH  
SEEK  
98.10  
pm  
2:45  
DISP  
The mode of equipment that is not  
connected is not displayed.  
P3  
PRESET  
BAND  
PS/AS  
2. Touch [BAND] to switch the reception band.  
Each touch of [BAND] switches the  
reception band as follows:  
Frequency display  
The frequency currently being received is  
displayed.  
Touching  
or  
on the left slide  
FM1 FM2 FM3 AM FM1...  
button in the standard operation display allows  
you to perform seek tuning or manual tuning.  
Tuning  
Preset No. display  
Touching  
on the right slide button in the  
There are 3 types of tuning mode available,  
seek tuning, manual tuning and preset tuning.  
standard operation display selects a preset  
memory.  
Title display  
Displays the name of the broadcast channel  
currently being received.  
Reception band display  
AM: AM band name  
FM1: FM band name  
PRESET  
Touching this displays a preset memory No. list.  
16  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Operations  
Seek tuning  
Preset memory  
Seek tuning is a function for automatically  
tuning stations with good reception.  
A total of 24 preset positions (6-FM1, 6-FM2, 6-  
FM3, 6-AM) exists to store individual radio  
stations in memory.  
1. Touch and hold [BAND] for 1 second or  
longer if “MANU” is displayed.  
Automatic tuning is possible when “SEEK” is  
displayed.  
1. Touch [BAND] to switch the reception band.  
2. Operate the frequency display to tune to a  
frequency to store.  
2. Touch  
on the frequency display.  
3. Touch [PRESET].  
SEEK UP”/“SEEK DOWN” is displayed, and  
tuning starts.  
Tuning automatically stops at stations with  
good reception.  
The preset memory No. list is displayed.  
4. Touch and hold the preset No. to store the  
station to for 2 seconds or longer.  
You will hear a long beep, and the station is  
stored in memory.  
To cancel tuning  
1. Touch  
on the frequency display again.  
Auto store  
Auto store is a function for storing up to 6  
stations that are automatically tuned in  
sequentially.  
Manual tuning  
There are 2 ways available: quick tuning and  
step tuning.  
1. Touch and hold [PS/AS] for 2 seconds or  
longer.  
In the step tuning mode, the frequency changes  
1 step at a time. In the quick tuning mode, you  
can quickly tune the desired frequency.  
A-STORE” is displayed.  
Stations with good reception are  
automatically searched, and are stored to  
preset memory (No.1 to No.6) in order  
from the station having the lowest  
frequency.  
1. Touch and hold [BAND] for 1 second or  
longer if “SEEK” is displayed.  
Manual tuning is possible when “MANU” is  
displayed.  
2. Operate the frequency display to tune to a  
frequency on which there is a broadcast.  
Notes:  
• When auto store is performed, stations stored to  
memory so far are cleared.  
Step tuning  
• When there are fewer than 6 stations with good  
reception, low frequencies are automatically  
returned to, and auto store is performed again. If  
there are fewer than 6 stations even after auto  
store is performed twice, stations stored so far  
remain in memory.  
Touch  
on the frequency display.  
Quick tuning  
Touch  
on the frequency display. Tuning  
stops when you take your finger away from the  
panel.  
Preset scan  
Recalling a preset station  
Preset scan is a function for receiving stations in  
the order that they are currently stored to preset  
No. so that broadcasts can be checked.  
Recalling a preset station is a function for tuning  
pre-stored stations.  
1. Touch [PRESET].  
1. Touch [PS/AS].  
The preset memory No. list is displayed.  
P-SCAN” is displayed.  
2. Touch the preset memory No.  
The currently stored stations are received  
in order for 7 seconds or longer each.  
Stations with poor reception are skipped,  
and the next station is received.  
In the standard operation display, preset  
No. can also be tuned by touching  
.
To cancel tuning  
1. Touch [RTN].  
DXZ866MP  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Radio Operations  
To cancel preset scan  
1. Touch [PS/AS].  
P-SCAN” display disappears and the  
stations that were being received when [PS/  
AS] was touched are received next.  
Instant station recall (ISR)  
Instant station recall is a special radio preset  
that instantly accesses a favorite radio station at  
a touch of a button. The ISR function even  
operates with the unit in other modes.  
• The factory default setting is “FM87.9MHz”.  
1. Press the [ISR] button.  
ISR” appears on the display.  
To return to the previous mode  
Press the [ISR] button again or press the [SRC]  
button.  
To store the station to “ISR”  
In the radio mode, tune the station to store, and  
press and hold the [ISR] button for 2 seconds or  
longer.  
You will hear a long beep, and the station  
currently being received is stored to ISR.  
18  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/MP3/WMA Operations  
a/d (only in the simple operation display)  
Touching these buttons selects the track to play.  
Touching and holding these buttons fast-  
forwards or fast-rewinds tracks.  
Screen displays in the CD/  
MP3 mode  
Standard operation display  
The standard operation display appears by  
pressing the [SRC] button to select the CD/MP3  
mode.  
/
(Appears only in MP3/WMA discs  
and the simple operation display)  
Touching these buttons selects the folder to  
play.  
Track No.  
display  
Title display  
Folder No.  
display  
MP3 (WMA)  
MP3/WMA  
MP3  
What is MP3?  
Don ,  
t
Stop Be  
01  
01  
MP3 is an audio compression method and  
classified into audio layer 3 of MPEG standards.  
This audio compression method has penetrated  
into PC users and become a standard format.  
TRACK  
FOLDER  
pm  
2:45  
DISP  
01:01  
TOP  
DISP  
This MP3 features the original audio data  
compression to about 10 percent of its initial  
size with a high sound quality. This means about  
10 music CDs can be recorded on a CD-R disc  
or CD-RW disc to allow a long listening time  
without having to change CDs.  
TOP  
Playing time  
display  
Simple operation display  
Pressing and holding the [MODE] button for 2  
seconds or longer switches the simple operation  
display.  
What is WMA?  
a/d  
WMA is the abbreviation of Windows Media  
Audio, an audio file format developed by  
Microsoft Corporation.  
Don ,  
t
Stop Be  
TRACK  
Notes:  
pm  
01:26  
2:45  
DISP  
01  
TOP  
• If you play a file with DRM (Digital Rights  
Management) for WMA remaining ON, no audio is  
output. (The DRM indicator blinks.)  
• Windows Media™, and the Windows® logo are  
trademarks, or registered trademarks of Microsoft  
Corporation in the United States and/or other  
countries.  
Playing time display  
Î00: 01: The playing time is displayed.  
Track No. display  
If  
or  
is touched, you can select the  
track to play, or fast-forward or fast-rewind  
tracks.  
To disable DRM (Digital Rights  
Management):  
Title display  
1. When using Windows Media Player 8, click  
on TOOLS OPTIONS COPY MUSIC  
tab, then under COPY SETTINGS, unclick  
the check box for PROTECT CONTENT.  
Then, reconstruct files.  
The selected title is displayed.  
Folder No. display (in the case of MP3/WMA)  
Touching  
selects folders.  
TOP  
2. When using Windows Media Player 9, click  
on TOOL OPTIONS MUSIC RECORD  
tab, then under Recording settings, unclick  
the Check box for RECORD PROTECTED  
MUSIC. Then, reconstruct files.  
Touching this starts play from the track at the  
top of the disc or folder being played.  
Touching this pauses or resumes play.  
Personally constructed WMA files are used  
at your own responsibility.  
DISP  
The display contents can be changed.  
DXZ866MP  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/MP3/WMA Operations  
Default value is “CD”.  
Precautions when creating  
MP3/WMA disc  
Usable sampling rates and bit rates:  
1. MP3: Sampling rate 11.025 kHz-48 kHz,  
Bit rate: 8 kbps-320 kbps / VBR  
2. WMA: Bit rate 48 kbps-192 kbps  
File extensions  
1. Press the [MODE] button.  
2. Touch [Å]/[Î] to go to the next page.  
3. Touch [MULTI SESS].  
Each touch of [MULTI SESS] toggles the  
MULTI SESS display between “CD” (play  
CD-DA) or “MP3/WMA” (play MP3/WMA).  
Setting  
Set to CD  
Set to MP3/WMA  
Disc  
1. Always add a file extension “.MP3” or  
.WMA” to MP3 or WMA file by using single  
byte letters. If you add a file extension other  
than specified or forget to add the file  
extension, the file cannot be played.  
Mixed with CD and  
MP3/WMA type tracks  
Play CD  
Play CD  
Play MP3/WMA  
CD-DA  
Play CD  
MP3/WMA disc  
Play MP3/WMA Play MP3/WMA  
2. Files without MP3/WMA data will not play.  
The indication “––:––” appears in the play  
time display if you attempt to play files  
without MP3/WMA data.  
The multi-session selection setting is  
reflected the next time you load a CD.  
Note:  
• When playing a CCCD (Copy Control CD), set the  
setting to CD type. When this is set to MP3/WMA  
type, the CD cannot be played normally in some  
cases.  
Logical format (File system)  
1. When writing MP3/WMA file on a CD-R disc  
or CD-RW disc, please select “ISO9660  
level 1, 2 or JOLIET or Romeo” as the  
writing software format. Normal play may not  
be possible if the disc is recorded on another  
format.  
Disc-In-Play function  
As long as the ignition key is turned to the ON or  
ACC position, this function allows you to turn the  
power to the unit and start playing the disc  
automatically when the disc is inserted even if  
the power is not turned on.  
2. The folder name and file name can be  
displayed as the title during MP3/WMA play  
but the title must be within 128 single byte  
alphabetical letters and numerals (including  
an extension).  
3. Do not affix a name to a file inside a folder  
having the same name.  
Loading a CD  
Folder structure  
1. Press the [Q] button.  
The control panel opens.  
1. A disc with a folder having more than 8  
hierarchical levels will be impossible.  
2. Insert the disc into the CD SLOT.  
When the disc is loaded, the control panel  
automatically closes after several seconds,  
and play starts.  
Number of files or folders  
1. Up to 255 files can be recognized per folder.  
Up to 500 files can be played.  
Notes:  
2. Tracks are played in the order that they were  
recorded onto a disc. (Tracks might not  
always be played in the order displayed on  
the PC.)  
• Never insert foreign objects into the CD SLOT.  
• If the CD does not insert easily, there may be  
another CD in the mechanism or the unit may  
require service.  
3. Some noise may occur depending on the  
type of encoder software used while  
recording.  
• Discs not bearing the  
or  
mark and  
CD-ROMs cannot be played by this unit.  
• Some CDs recorded in the CD-R/CD-RW mode  
may not be usable.  
Loading 8 cm compact discs  
No adapter is required to play an 8 cm CD.  
Insert the 8 cm CD into the center of the CD  
SLOT.  
Multisession function  
When a disc contains both CD-DA and MP3/  
WMA type tracks mixedly, you can select which  
type of the recorded tracks to play.  
20  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/MP3/WMA Operations  
Backup eject function  
Selecting a track  
You can eject a disc by pressing the [Q] button  
even if the engine key or ACC is at the OFF  
position.  
When a CD-R/CD-RW recorded with an MP3  
file or a WMA file is loaded, you can select only  
tracks recorded to the same folder by touching  
on the track display.  
1. To listen to the next track, touch  
track display.  
on the  
CAUTION  
When the disc is ejected, press the [Q]  
button to close the control panel. If the  
control panel is left open, you will hear a  
double beep, and the control panel  
automatically closes.  
2. To listen to the previous track, touch  
twice on the track display.  
Touching  
touch  
plays the next track. If you  
more times, the track advances  
ahead to the track for the number of times  
you touched  
Touching  
you touch  
back to the track for the number of times you  
touched  
and that track is played.  
plays the previous track. If  
more times, the track moves  
1. Press the [Q] button.  
The control panel opens.  
2. Press the [Q] button.  
The disc is ejected.  
and that track is played.  
twice on the track display  
Note:  
If you touch  
• Always close the SLOPING CONSOLE after  
opening it or ejecting the CD.  
while the start of the track is being played,  
the track 2 tracks back is sometimes  
played.  
CAUTION  
To select a folder  
To select a different folder, touch  
folder display on the right.  
on the  
• Be careful not to catch your hand or  
fingers while closing the SLOPING  
CONSOLE.  
• Do not try to put your hand or fingers in  
the disc insertion slot. Also never insert  
foreign objects into the slot.  
• Do not insert discs where adhesive comes  
out from cellophane tape or a rental CD  
label, or discs with marks where  
cellophane tape or rental CD labels were  
removed. It may be impossible to extract  
these discs from the unit and they may  
cause the unit to break down.  
Play list mode  
This function allows you to play tracks, up to  
latest 5 time stamps, by reading the play list  
information written on the disc.  
1. Press the [MODE] button.  
2. Touch [Å]/[Î] to go to the next page.  
3. Touch [PLAY LIST].  
MODE  
2
2
MULTI  
SESS  
PLAY  
LIST  
Listening to a disc already  
loaded in the unit  
MP3 WMA  
RTN  
1. Press the [SRC] button to select the CD/  
MP3 mode.  
The operation of selecting the play list or  
tracks in the play list is the same as that of  
selecting a folder or tracks in a folder.  
Play list play is possible only when there is  
a file whose extension is “.M3U” on the  
CD-R/RW.  
Up to 5 play lists can be recognized, and  
up to 255 files can be recognized per play  
list.  
Play automatically starts when the mode  
changes to the CD/MP3 mode.  
Pausing play  
1. Touch [  
].  
To resume play  
Stopping play of play list  
1. Press the [MODE] button.  
1. Touch [  
] again.  
DXZ866MP  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/MP3/WMA Operations  
2. Touch [Å]/[Î] to go to the next page.  
3. Touch [PLAY LIST].  
Scan play starts from the next track after  
the track currently being played.  
To cancel scan play  
Notes:  
• The SCN/RPT/RDM functions cannot be used  
while in the play list mode.  
1. Press the [MODE] button.  
• The title changes from folder name to play list  
name.  
Folder scan play  
This function allows you to locate and play the  
first 10 seconds of the first track of all the folders  
recorders on a disc.  
Making a play list  
1. Write desired tracks to a CD-R/RW, etc. Be  
sure to use alphanumeric/ASCII characters  
for all file names.  
1. Press the [MODE] button.  
2. Touch [FOLDER SCAN].  
Folder scan play starts from the folder  
2. Make a play list by using a multimedia  
player, etc. and save the data. The file format  
must be M3U.  
following the folder that is playing.  
To cancel folder scan play  
1. Press the [MODE] button.  
3. Again, write this play list to the CD-R/RW,  
etc.  
Notes:  
• When writing to a CD-R/RW, etc., be sure to use  
alphanumeric/ASCII characters.  
• Up to 5 layers can be recognized as a list. For  
written play lists, latest 5 lists are recognized in  
the order in which they are written.  
Repeat play  
This function allows you to play the current track  
repeatedly.  
1. Press the [MODE] button.  
2. Touch [TRACK RPT].  
• When writing to a CD-R/RW, etc., turn off the Disc  
At Once function.  
• When adding a play list, it is recommended to  
write it in the “Root” folder.  
To cancel repeat play  
1. Press the [MODE] button.  
Fast-forward/fast-rewind  
Folder repeat play  
1. To fast-forward, touch  
display.  
on the track  
This function allows you to play the current  
folder repeatedly.  
2. To fast-rewind, touch  
display.  
on the track  
1. Press the [MODE] button.  
2. Touch [FOLDER RPT].  
Top function  
To cancel folder repeat play  
1. Press the [MODE] button.  
The top function resets the CD player to the first  
track of the disc.  
1. Touch [TOP].  
Random play  
Play starts from the first track (track No.1).  
This function allows you to play all tracks on the  
disc at random.  
When the disc contains 2 or more folders, all of  
the tracks in the folder are played at random,  
followed by all of the tracks in the next folder.  
This is repeated for all folders.  
Scan play  
This function allows you to locate and play the  
first 10 seconds of all the tracks recorded on a  
disc.  
1. Press the [MODE] button.  
2. Touch [TRACK RDM].  
1. Press the [MODE] button.  
2. Touch [TRACK SCAN].  
22  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD/MP3/WMA Operations  
To cancel random play  
1. Press the [MODE] button.  
Folder random play  
This function allows you to play all folders on the  
disc at random.  
1. Press the [MODE] button.  
2. Touch [FOLDER RDM].  
To cancel folder random play  
1. Press the [MODE] button.  
DXZ866MP  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sound Adjustment  
3. Touch  
on the right of the display to  
Adjustment items  
select the ADF mode.  
You can adjust a sound effect or tone quality to  
your preference.  
ADF MODE  
1
ADF 1  
Anti Distortion Filter (ADF) .................... Page 24  
MAGNA BASS EXTEND ....................... Page 24  
Sub-woofer speaker volume  
RTN  
(SW VOLUME)................................. Page 25  
Bass setting (BASS) ............................. Page 25  
Treble setting (TREBLE) ....................... Page 25  
Balance (BALANCE) ............................. Page 25  
Fader (FADER) ..................................... Page 25  
Filter (FILTER)....................................... Page 26  
Select one of “USER”, “1”, “2”, “3”, or  
OFF”.  
4. To change the details of the ADF setting,  
press the [ADJ] button.  
5. Touch  
select the desired item.  
Each touch of switches the  
on the left of the display to  
adjustment item display as follows:  
Setting the ADF  
Adjustment item (when USER is  
selected in step 3)  
• ADF is the abbreviation of Anti Distortion  
Filter.  
The adopted “Liveliness Enhancement Filter”  
and “Sound Tone Compensation” functions  
allow well-modulated realistic playback without  
affecting the characteristics of the original sound  
tone.  
BASS TREBLE COMP BASS...  
Adjustment item (when 1 to 3 is  
selected in step 3)  
LEVEL COMP LEVEL...  
This unit is provided with 4 types of sound tone  
effects stored in memory. Select the one you  
prefer.  
6. Touch  
on the right of the display to  
adjust the item.  
BASS” and “TREBLE” can be adjusted  
within the range 1 to 13.  
LEVEL” can be adjusted within the range -  
3 to +3.  
ADF-1 : Suitable for genuine speakers  
ADF-2 : Suitable for separate speakers  
ADF-3 : Suitable for co-axial speakers  
Select either “ON” or “OFF” for “COMP”.  
USER : This setting can be adjusted by the  
user to his or her individual preference.  
7. Press the [SOUND] button to return to the  
original mode.  
OFF :  
No sound effect  
• The factory default setting is “OFF”.  
Notes:  
Setting MAGNA BASS  
EXTEND  
• As the volume changes when ADF is switched,  
switch ADF with the volume and “SW VOLUME”  
(sub-woofer) turned down as far as possible.  
The MAGNA BASS EXTEND does not adjust  
the low frequencies like the normal sound  
adjustment function, but emphasizes the deep  
bass frequencies to provide you with a dynamic  
sound.  
1. Press the [SOUND] button.  
2. Touch [ADF].  
SOUND  
1
1
• The factory default setting is "OFF".  
1. Press the [SOUND] button.  
M-BASS  
EX  
ADF  
OFF  
BASS  
TREBLE  
BALANCE  
FADER  
0
OFF  
0
RTN  
2. Touch [M-BASS EX] to select "ON" or  
"OFF".  
Each time you touch [M-BASS EX], the  
adjustment item changes as following  
order:  
OFF ON OFF...  
3. Press the [SOUND] button to return to the  
original mode.  
24  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sound Adjustment  
Note:  
Adjusting the treble (Gain,  
Frequency)  
When "1", "2", "3", or "USER" is selected for ADF  
(Anti Distortion Filter), setting of MAGNA BASS EX  
cannot be performed.  
This adjustment can only be performed when  
the ADF (Anti Distortion Filter) is set to "OFF".  
1. Press the [SOUND] button.  
2. Touch [TREBLE].  
Adjusting the sub-woofer  
• "SW VOLUME" (sub-woofer) can be adjusted  
only when the "SUB-WOOFER" is set to "ON"  
(cf. page 32).  
3. Touch  
select the item.  
Each touch of  
on the left of the display to  
• The factory default setting for SW VOLUME is  
0”.  
switches the  
adjustment items as follows:  
1. Press the [SOUND] button.  
GAIN FREQUENCY GAIN...  
2. Touch [SW VOLUME].  
4. Touch  
on the right of the display to  
SW VOLUME  
adjust the setting.  
The factory default setting for "GAIN" is  
"0". (Adjustment range: -6 to +6)  
The factory default setting for  
"FREQUENCY" is "12k". (Adjustment  
8kHz/12kHz)  
0
RTN  
3. Touch  
on the right of the display and  
adjust the item as desired.  
This item can be adjusted within the range  
-5 to +5.  
5. When the adjustment is complete, press the  
[SOUND] button to return to the original  
mode.  
4. Press the [SOUND] button to return to the  
original mode.  
Adjusting balance/fader  
BALANCE:  
Adjusts the volume balance between the left  
and right speakers.  
Adjusting the bass (Gain,  
Frequency, Q-curve)  
FADER:  
This adjustment can only be performed when  
Adjusts the volume balance between the front  
and rear speakers.  
the ADF (Anti Distortion Filter) is set to "OFF".  
1. Press the [SOUND] button.  
2. Touch [BASS].  
• The factory default setting for BALANCE is  
0” and for FADER is “0”.  
3. Touch  
select the item.  
Each touch of  
on the left of the display to  
1. Press the [SOUND] button.  
2. Touch [BALANCE] or [FADER].  
switches the  
BALANCE  
adjustment items as follows:  
0
GAIN FREQUENCY Q GAIN...  
RTN  
4. Touch  
on the right of the display to  
adjust the setting.  
3. Touch  
on the right of the display and  
The factory default setting for "GAIN" is  
"0". (Adjustment range: -6 to +8)  
The factory default setting for  
"FREQUENCY" is "50". (Adjustment 50/  
80/120Hz)  
adjust the item as desired.  
BALANCE” can be adjusted within the  
range L13 (left side emphasized) and R13  
(right side emphasized).  
FADER” can be adjusted within the range  
R12 (rear side emphasized) and F12 (front  
side emphasized).  
The factory default setting for "Q" is "1".  
(Adjustment 1/1.25/1.5/2)  
5. When the adjustment is complete, press the  
[SOUND] button to return to the original  
mode.  
4. Press the [SOUND] button to return to the  
original mode.  
DXZ866MP  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sound Adjustment  
Adjusting the filter frequency  
Filter frequency  
You can set a filter frequency value best suited  
for your speakers.  
* This item can be adjusted only when “SUB-  
WOOFER” is set to “ON”.  
• The factory default setting for FILTER is  
THROUGH”.  
Filter adjustment  
SUB-W LPF (Subwoofer Low-Pass Filter)  
adjustment  
This filter cuts the signals above the selected  
frequency value.  
Each touch switches the frequency value as  
follows:  
THROUGH 50Hz 80Hz 120Hz ➜  
THROUGH...  
Select the frequency that suits your subwoofer.  
Set to “THROUGH” if you use powered  
subwoofers with built-in low-pass filters.  
1. Press the [SOUND] button.  
2. Touch [FILTER].  
3. Touch  
on the right of the display to  
select the frequency value.  
• Select from THROUGH, 50Hz, 80Hz, or  
120Hz.  
4. Press the [SOUND] button to return to the  
original mode.  
26  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
Screen display in the TITLE  
INPUT  
CD changer mode  
DCZ625 connected  
CDC655Tz connected 100 titles  
CDC1255z connected 50 titles  
Number of titles  
100 titles  
The “TITLE INPUT” screen appears when you  
enter a title.  
Title  
display  
TEXT  
display  
FONT  
display  
1. Either receive the radio or TV station, or play  
a CD for which you want to enter the title.  
2. Touch [DISP].  
3. Touch [INPUT].  
DISPLAY EDIT  
TITLE INPUT  
a
FONT  
Me I o dy  
a-Z  
TEXT  
MEMO  
RTN  
<<  
TITLE  
P
05  
ABCDE  
BGV  
L
-
BLUE  
/
RTN  
RTN  
MEMO  
SP/ANA  
COLOR  
INPUT  
The TITLE INPUT screen appears.  
FONT display  
4. Touch [ ]/[ ] to move the cursor to indicate  
the input position.  
A : Capital alphabet letters  
a : Small alphabet letters  
1 : Numbers  
TITLE INPUT  
A
FONT  
A-Z  
TEXT  
: Symbols  
¯
A: Umlaut  
MEMO  
RTN  
Title display  
The currently entered title is displayed.  
Up to ten characters can be input.  
TEXT display  
CAUTION  
Touch  
to select the character to enter.  
Pressing the reset button clears all user  
memories such as titles stored on this unit.  
/
Touching these buttons moves the cursor  
indicating input position.  
5. Touch  
text.  
on [FONT] to select the type of  
RTN  
Each touch of  
switches the type of  
Touching this cancels entry of titles, and returns  
the display to the original screen.  
text as follows:  
Capital alphabet letters  
(space) A B C D E F G H I J K L M N O P Q  
R S T U V W X Y Z  
Small alphabet letters  
a b c d e f g h i j k l m n o p q r s t u v w x y z  
Numbers  
MEMO  
Touching this stores the title that was input, and  
returns the display to the original screen.  
Entering titles  
0 1 2 3 4 5 6 7 8 9  
Symbols  
You can give radio/TV stations and CDs a title  
up to 10 characters long. These titles can be  
displayed when broadcasts are received or  
when playing CDs.  
Umlaut  
The number of titles that can be entered is as  
follows:  
Å Ä Ë É E Ê Ï Æ Ø å ä ë é e ê ï ö ü æ ø  
6. Touch  
on [TEXT] to determine the  
Mode  
Number of titles  
50 titles  
20 titles  
characters to enter.  
CD mode  
TV mode  
Radio mode  
7. Repeat steps 4 to 6 to enter the title.  
8. Touch [MEMO].  
30 titles  
You will hear a long beep, and the title is  
stored in memory.  
DXZ866MP  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
4. When ENT” is displayed at the right of the  
display, touch [ENT] to switch to the  
adjustment details display.  
When a new title is stored beyond the  
maximum number of titles  
In the case of a radio or TV station  
Titles not stored to preset channels and ISR  
(radio stations only) are automatically cleared,  
and the new title is stored in memory.  
5. Touch  
on the right of the display to  
set the details.  
To return to the original mode  
1. Press the [ADJ] button again.  
In the case of a CD  
Titles of CDs that have been played the least  
are cleared, and the new title is stored in  
memory.  
To call up the last operated item  
1. Touch [RECENT].  
Clearing titles  
1. Either receive the radio or TV station, or play  
a CD whose title you want to clear.  
2. Touch [DISP].  
3. Touch [INPUT].  
4. Touch and hold [RTN] for 2 seconds or  
longer to erase the title.  
5. Touch [MEMO].  
Erasing is performed by overwriting with a  
blank title.  
Triggered audio mute for  
cellular telephones  
This unit requires special wiring to mute the  
audio signal automatically when a cellular  
telephone rings in the car.  
This function is not compatible with all cellular  
telephones. Contact your local authorized  
Clarion dealer for information on proper  
installation and compatibility.  
Changing settings  
Selecting setting items  
1. Press the [ADJ] button.  
The mode changes to the adjust mode.  
ADJ  
1
1
APPEA-  
RANCE  
SOUND  
TUNER  
SETTING  
RECENT  
RTN  
2. Touch [APPEARANCE], [SOUND],  
[TUNER], or [SETTING].  
3. Touch  
on the left of the display to  
select the item to set.  
28  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
Setting items  
Main item  
Sub item  
APPEARANCE  
CLOCK EDIT  
• Clock setting (cf. page 30)  
MSG INFO  
• Setting the message display ON/OFF (cf. page 30)  
MSG INPUT  
• Message information input (cf. page 30)  
DIMMER IN  
• Auto-dimmer setting (cf. page 31)  
DMR LEVEL  
• Setting the dimmer level (cf. page 31)  
BRIGHT  
• Adjusting the display brightness (cf. page 31)  
BLINK LED  
• Making the LED blink when DCP is removed (cf. page 31)  
BEEP  
• Setting beep (cf. page 32)  
SCROLL SPD  
• Adjusting the scroll speed (cf. page 32)  
SRC ICON  
• Setting the source icon display (cf. page 32)  
SOUND  
TUNER  
SUB WOOFER  
• Setting sub woofer speaker ON/OFF (cf. page 32)  
AMP CANCEL  
• Setting internal amplifier use ON/OFF (cf. page 32)  
TV AREA  
• Setting the TV area (cf. page 40)  
TV DIVER  
• Setting TV diversity (cf. page 40)  
SETTING  
AUX SENS  
• Setting the portable audio (AUX) input level (cf. page 33)  
SYSTEM CHECK  
• Performing a system check (cf. page 33)  
CODEMATIC  
• Setting security (cf. page 34)  
SLIDE CONT  
• Setting the slide direction of the slide buttons (cf. page 34)  
DXZ866MP  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
3. Touch  
on the left of the display to  
Setting the clock (CLOCK)  
When the power is OFF, the clock is displayed.  
The clock is displayed in 12-hour format.  
select "MSG INFO".  
ADJ APPEARANCE  
MSG INFO  
OFF  
1. Press the [ADJ] button.  
2. Touch [APPEARANCE].  
RTN  
3. Touch  
on the left slide button to select  
4. Touch  
on the right of the display to  
CLOCK EDIT” and touch [ENT].  
select “ON” or “OFF”.  
ADJ APPEARANCE  
5. Press the [ADJ] button to return to the  
[
]
ENT  
CLOCK EDIT  
original mode.  
RTN  
Entering messages to display  
in message information (MSG  
INPUT)  
The time (e.g. “2pm:45”) currently set on this  
unit is displayed, and the mode changes to  
the time setting mode.  
4. Touch  
hours.  
on the left slide button to set  
• Up to 30 characters can be entered.  
• The factory default setting is “Welcome to  
Optimedia”.  
ADJ APPEARANCE CLOCK  
2
pm  
:
45  
1. Press the [ADJ] button to set to the adjust  
mode.  
SET  
RTN  
2. Touch [APPEARANCE].  
If you operate another button while you  
are setting the time, the time is not  
adjusted.  
3. Touch  
on the left of the display to  
select "MSG INPUT".  
ADJ-APPEARANCE  
5. Touch  
on the right slide button to set  
[
]
ENT  
MSG INPUT  
minutes.  
RTN  
6. Touch [SET].  
You will hear a long beep, and the time is  
set.  
4. Touch [ENT].  
The mode changes to the message entry  
mode.  
Notes:  
• The clock cannot be adjusted when the power is  
OFF.  
• When the battery has been removed for  
maintenance or for repair, set the time again.  
5. Touch [ ]/[ ] to determine the entry  
position.  
MESSAGE INPUT  
7. Press the [ADJ] button to return to the  
A
FONT  
We I come to  
A-Z  
TEXT  
original mode.  
MEMO  
RTN  
Displaying messages (MSG  
INFO)  
6. Touch  
text.  
on [FONT] to select the type of  
Each touch of  
text. For details, see page 27.  
switches the type of  
This function allows you to display a message  
on the display when no operation is performed  
for more than 30 seconds.  
7. Touch on [TEXT] to determine the  
character to enter.  
• The factory default setting is “OFF”.  
8. Repeat steps 5 to 7 to enter the message.  
1. Press the [ADJ] button to set to the adjust  
9. Touch [MEMO].  
mode.  
You will hear a long beep, and the message  
is stored in memory.  
2. Touch [APPEARANCE].  
10. Press the [ADJ] button to return to the  
original mode.  
30  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
5. Press the [ADJ] button to return to the  
Setting the auto-dimmer  
(DIMMER IN)  
original mode.  
This function allows you to dim the lighting of  
the display matched to the illumination or the  
brightness inside your car.  
Adjusting the brightness of  
the display (BRIGHT)  
Select either “AUTO” (interlocked to the  
brightness inside your car) or “ILLUMI”  
(interlocked to the illumination inside your car)  
as the auto-dimmer setting.  
You can adjust the brightness of the display to  
match the mounting angle of the unit.  
• The factory default setting is “5”.  
• When the auto-dimmer function is set to  
AUTO”, the brightness of the display is  
dimmed according to the brightness detected  
by this sensor.  
• Set the dimmer setting at DMR LEVEL.  
• The factory default setting is “AUTO”.  
1. Press the [ADJ] button to set to the adjust  
mode.  
2. Touch [APPEARANCE].  
3. Touch  
on the left of the display to  
select “BRIGHT”.  
ADJ APPEARANCE  
1. Press the [ADJ] button to set to the adjust  
mode.  
BRIGHT  
5
2. Touch [APPEARANCE].  
RTN  
3. Touch  
on the left of the display to  
select “DIMMER IN”.  
4. Touch  
on the right of the display to  
ADJ APPEARANCE  
adjust the brightness.  
This setting item can be adjusted within  
the range 1 to 12.  
Adjust this setting item while viewing how  
the appearance of the display changes.  
D I MMER IN  
AUTO  
RTN  
4. Touch  
on the right of the display to  
5. Press the [ADJ] button to return to the  
select “AUTO” or “ILLUMI”.  
original mode.  
5. Press the [ADJ] button to return to the  
original mode.  
Making the LED blink when  
DCP is removed (BLINK LED)  
Setting the dimmer level  
(DMR LEVEL)  
You can make the LED on this unit blink when  
the DCP is removed.  
This function allows you to set how much the  
displayed is to be dimmed.  
• The factory default setting is “OFF”.  
1. Press the [ADJ] button to set to the adjust  
• The factory default setting is “3”.  
mode.  
1. Press the [ADJ] button to set to the adjust  
2. Touch [APPEARANCE].  
mode.  
3. Touch  
on the left of the display to  
2. Touch [APPEARANCE].  
select “BLINK LED”.  
3. Touch  
on the left of the display to  
ADJ APPEARANCE  
select “DMR LEVEL”.  
BL INK LED  
OFF  
ADJ APPEARANCE  
DMR LEVEL  
3
RTN  
RTN  
4. Touch  
on the right of the display to  
select “ON” or “OFF”.  
4. Touch  
on the right of the display to  
5. Press the [ADJ] button to return to the  
set the dimmer level.  
Select one of OFF (dimming OFF, bright),  
1 (slightly dimmed) to 5 (dark).  
original mode.  
DXZ866MP  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
1. Press the [ADJ] button to set to the adjust  
Setting the beep for when  
mode.  
buttons are operated (BEEP)  
2. Touch [APPEARANCE].  
The short or long high-pitched tone you hear  
when a button is operated is called a “BEEP”.  
3. Touch  
on the left of the display to  
select “SRC ICON”.  
• The factory default setting is “ON”.  
ADJ APPEARANCE  
1. Press the [ADJ] button to set to the adjust  
SRC I CON  
I CON  
mode.  
2. Touch [APPEARANCE].  
RTN  
3. Touch  
on the left of the display to  
select “BEEP”.  
4. Touch  
on the right of the display to  
select “ICON” or “SPE/ANA”.  
ADJ APPEARANCE  
5. Press the [ADJ] button to return to the  
BEEP  
OFF  
original mode.  
RTN  
4. Touch  
on the right of the display to  
Setting speaker ON/OFF  
(SUB-WOOFER)  
select “ON” or “OFF”.  
5. Press the [ADJ] button to return to the  
Set the sub-woofer (SUB-WOOFER) ON/OFF.  
original mode.  
Be sure to set this setting to “OFF” when there  
is no sub-woofer.  
• The factory default setting is “ON”.  
Adjusting the title scroll  
speed (SCROLL SPD)  
1. Press the [ADJ] button to set to the adjust  
mode.  
This feature allows you to slow down the scroll  
speed when the scroll speed is too fast, making  
it difficult to view the screen.  
2. Touch [SOUND].  
3. Touch  
on the right of the display to  
select "ON" or "OFF".  
• The factory default setting is “SPEED 1”.  
ADJ SOUND  
1. Press the [ADJ] button to set to the adjust  
SUB WOOFER  
ON  
mode.  
2. Touch [APPEARANCE].  
RTN  
3. Touch  
on the left of the display to  
select “SCROLL SPD”.  
4. Press the [ADJ] button to return to the  
ADJ APPEARANCE  
original mode.  
SCROLL SPD  
1
RTN  
Setting internal amplifier use  
ON/OFF (AMP CANCEL)  
4. Touch  
on the right of the display to  
Set internal amplifier use ON/OFF matched to  
whether or not an external amplifier is used.  
adjust the sensitivity.  
This setting item can be adjusted within  
the range SPEED 1 to SPEED 4.  
Set AMP CANCEL to “ON” (internal amplifier  
use OFF) when an external amplifier is  
connected and the internal amplifier is not used.  
5. Press the [ADJ] button to return to the  
original mode.  
• The factory default setting is “OFF” (internal  
amplifier used).  
1. Press the [ADJ] button to set to the adjust  
Setting the source icon  
(SRC ICON)  
mode.  
2. Touch [SOUND].  
You can change the source icon on the display.  
• The factory default setting is “ICON”.  
32  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
3. Touch  
on the left of the display to  
Performing a system check  
(SYSTEM CHECK)  
select “AMP CANCEL”.  
ADJ SOUND  
This function allows you to perform a system  
check when an external equipment is connected  
to this unit.  
AMP CANCEL  
OFF  
RTN  
1. Press the [ADJ] button to set to the adjust  
mode.  
4. Touch  
on the right of the display to  
select “ON” or “OFF”.  
2. Touch [SETTING].  
5. Press the [ADJ] button to return to the  
3. Touch  
on the left of the display to  
original mode.  
select “SYSTEM CHECK”.  
ADJ SETTING  
[
]
SYSTEM  
START  
CHECK  
AUX function  
This system has an external RCA input so you  
can listen to sounds and music from external  
devices connected to this unit.  
RTN  
4. Touch [START].  
The confirmation display appears.  
5. Touch [OK].  
Setting the input level (AUX  
SENS) of portable audio (AUX  
mode)  
ADJ SETTING  
OK  
CANCEL  
This function allows you to set the input level of  
optional external devices connected to this unit.  
After this operation, the display returns to  
the original mode.  
• The factory default setting is “MID”.  
1. Press the [ADJ] button to set to the adjust  
mode.  
2. Touch [SETTING].  
3. Touch  
on the left of the display to  
select "AUX SENS".  
ADJ SETTING  
AUX  
MID  
SENS  
RTN  
4. Touch  
set the input level.  
Select LOW, MID or HIGH.  
Notes:  
on the right of the display to  
• When the input level is overloaded, “OVERLOAD”  
appears. Adjust AUX SENS or the input level so  
that “OVERLOAD” disappears.  
5. Press the [ADJ] button to return to the  
original mode.  
DXZ866MP  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Common Operations  
CODE MATIC  
Using the security function  
(CODEMATIC)  
This function prevents persons who do not know  
the touch sequence from easily operating this  
unit. The Touch Code display appears when  
DCP is attached and the power is turned ON  
with “CODEMATIC” set to “ON”.  
1
2
3
4
When you touch 4 times, and 4 indicators  
light, you will hear a long beep, and the  
original mode is returned to.  
If you touch the display in this screen in the  
preset order, “SUCCESSFUL” is displayed and  
the power is turned OFF.  
To cancel CODEMATIC  
If you have forgotten the touch order, either  
touch [4], [1], [3] and then [2] in that order, or  
press [SCN] on the remote control unit.  
When the power is next turned ON, the Touch  
Code display does not appear, and the main  
display in the radio mode or CD mode is  
displayed.  
• The factory default setting is “OFF”.  
Setting the slide direction of  
the slide buttons (SLIDE  
CONT)  
1. Press the [ADJ] button to set to the adjust  
mode.  
2. Touch [SETTING].  
This function allows you to set the direction of  
the left and right slide buttons.  
3. Touch  
on the left of the display to  
select “CODEMATIC”.  
• The factory default setting is “UP +”.  
ADJ SETTING  
1. Press the [ADJ] button to set to the adjust  
CODEMAT I C  
OFF  
mode.  
2. Touch [SETTING].  
RTN  
3. Touch  
on the left of the display to  
2 types of items are displayed for  
select “SLIDE CONT”.  
CODEMATIC”, items for which “ON” or  
OFF” is displayed at the right of the screen,  
and items for which “INPUT” is displayed at  
the right of the screen. Here, select the item  
for which “ON” or “OFF” is displayed at the  
right of the display.  
ADJ SETTING  
SLIDE CONT  
UP  
RTN  
4. Touch  
on the right of the display to  
select “UP +” or DOWN +”.  
4. Touch  
select “ON” or “OFF”.  
5. Touch on the left of the display to  
select “CODEMATIC”.  
on the right of the display to  
5. Press the [ADJ] button to return to the  
original mode.  
ADJ SETTING  
CODEMATIC  
INPUT  
RTN  
Here, select the item for which “INPUT” is  
displayed at the right of the display.  
6. Touch [INPUT].  
The Touch Code display appears.  
7. Enter the touch code.  
Touch [1] to [4] at the bottom of the display  
at random. You can also repeatedly touch  
the same number.  
34  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. OPERATIONS OF ACCESSORIES  
CD Changer Operations  
Playing time display  
Î00:01: The playing time is displayed.  
CD changer  
When an optional CD changer is connected  
through the CeNET cable, this unit can control  
CD changer operations. This unit can be  
connected to a total of 2 CeNET-wired CD  
changers.  
Track No. display  
Touching  
or  
allows you to select  
the track to play, or fast-forward/fast-rewind  
tracks.  
Title display  
When 2 CD changers are connected  
The selected title is displayed.  
Press the [SRC] button to select the changer  
connected to this unit. (Each press of the [SRC]  
button switches the changer.)  
Disc No. display  
Touching  
selects discs.  
• If the CD changer does not contain a  
magazine, “NO MAGAZINE” is displayed, and  
if the magazine does not contain a CD, “NO  
DISC” is displayed.  
• For details on the title display, see “Switching  
the title display” (cf. page 15).  
s
Touching this pauses or resumes play.  
DISP  
The display contents can be changed.  
a/d (only in the simple operation display)  
Touching these selects the track to play.  
Touching and holding these fast-forwards/fast-  
rewinds tracks.  
Screen displays in the  
changer mode  
/
(Only in the simple operation  
Standard operation display  
The standard operation display appears by  
pressing the [SRC] button to select changer  
modes.  
display)  
Touching these buttons selects the disc to play.  
CAUTION  
Track No.  
display  
Title  
display  
Disc No.  
display  
CD-ROM discs cannot be played from every  
CD changer. This depends on the model.  
Note:  
01  
1
TELL ME  
TRACK  
DISC  
• Some CDs recorded in the CD-R/CD-RW mode  
may not be usable.  
pm  
2:45  
DISP  
03:09  
DISP  
Playing time  
display  
s
Simple operation display  
Pressing and holding [MODE] button for 2  
seconds or longer switches the simple operation  
display.  
a/d  
TELL ME  
TRACK  
DISC  
pm  
2:45  
DISP  
03:29  
1
01  
DXZ866MP  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Changer Operations  
Selecting the changer mode  
Fast-forward/fast-rewind  
1. Press the [SRC] button to select the changer  
mode.  
1. To fast-forward, touch  
display.  
on the track  
Each time you press the [SRC] button, the  
display switches as follows:  
2. To fast-rewind, touch  
display.  
on the track  
Radio CD/MP3 (CD changer) ➜  
(DVD changer) (TV) AUX Radio...  
Scan play  
The mode of equipment that is not  
connected is not displayed.  
Play starts automatically when the mode  
changes to the changer mode.  
Scan play locates and plays the first 10 seconds  
of each track on a disc automatically. This  
function continues on the disc until it is  
canceled.  
The scan play function is useful when you want  
to select a desired track.  
Pausing play  
1. Touch [s].  
1. Press the [MODE] button.  
2. Touch [TRACK-SCAN].  
To resume play  
1. Touch [s] again.  
Scan play starts from the next track after  
the track currently being played.  
To cancel scan play  
Selecting a CD  
1. Press the [MODE] button.  
1. Touch  
select a disc.  
Play starts.  
on the disc No. display to  
Disc scan play  
If magazine does not contain the disc you  
selected, the No. for that disc is not  
displayed.  
Disc scan play locates and plays the first 10  
seconds of the first track on each disc in the  
currently selected changer. This function  
continues automatically until it is canceled.  
Disc scan play is useful when you want to select  
a desired disc.  
Selecting a track  
1. To listen to the next track, touch  
track display.  
on the  
1. Press the [MODE] button.  
2. Touch [DISC SCAN].  
2. To listen to the previous track, touch  
twice on the track display.  
Disc scan play starts from the next disc  
after the disc currently being played.  
Touching  
touch  
plays the next track. If you  
more times, the track advances  
To cancel disc scan play  
1. Press the [MODE] button.  
ahead to the track for the number of times  
you touched  
Touching  
and that track is played.  
plays the previous track. If  
more times, the track moves  
you touch  
Repeat play  
back to the track for the number of times you  
touched  
If you touch  
Repeat play continuously plays the current track.  
This function continues automatically until it is  
canceled.  
and that track is played.  
twice on the track display  
while the start of the track is being played,  
the track 2 tracks back is sometimes  
played.  
1. Press the [MODE] button.  
2. Touch [TRACK RPT].  
To cancel repeat play  
1. Press the [MODE] button.  
36  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CD Changer Operations  
Disc repeat play  
After all the tracks on the current disc have  
been played, disc repeat play automatically  
replays the current disc over from the first track.  
This function continues automatically until it is  
canceled.  
1. Press the [MODE] button.  
2. Touch [DISC RPT].  
To cancel disc repeat play  
1. Press the [MODE] button.  
Random play  
Random play selects and plays individual tracks  
on the disc in no particular order. This function  
continues automatically until it is canceled.  
1. Press the [MODE] button.  
2. Touch [TRACK RDM].  
To cancel random play  
1. Press the [MODE] button.  
Disc random play  
The disc random play selects and plays  
individual tracks or discs automatically in no  
particular order. This function continues  
automatically until it is canceled.  
1. Press the [MODE] button.  
2. Touch [DISC RDM].  
To cancel disc random play  
1. Press the [MODE] button.  
DXZ866MP  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV Operations  
Reception band display  
TV tuner function  
TV1 : Band name  
When an optional TV tuner is connected through  
the CeNET cable, this unit controls all TV tuner  
functions. To watch TV, you need a TV tuner and  
a monitor.  
Preset No. display  
Touching  
on the right slide button in the  
standard operation display selects a preset  
memory.  
Touching [PRESET] displays the preset memory  
number list.  
Screen displays in the TV  
mode  
PS/AS  
Touching this starts a preset scan.  
Touching and holding this for 2 seconds or  
longer starts an auto store.  
Touching this during the preset scan/auto scan  
ends the operation.  
Standard operation display  
The standard operation display appears by  
pressing the [SRC] button to select the TV  
mode.  
Reception  
Channel display  
band display  
Preset No.  
display  
BAND  
Touching this switches the reception band.  
Touching and holding this for 1 second or longer  
toggles between the manual tuning mode and  
the seek tuning mode.  
Title display  
3ch  
TV1  
P1  
a/d (only in the simple operation display)  
Touching these buttons enables seek tuning or  
step tuning (in the manual tuning mode).  
Touch and holding these buttons enables quick  
tuning (in manual tuning mode).  
MANU  
P.CH  
pm  
2:45  
PRESET  
BAND  
PS AS  
DISP  
DISP  
PRESET  
PS/AS  
SEEK/MANU  
indicator  
BAND  
DISP  
The display contents can be changed.  
Simple operation display  
Pressing and holding the [MODE] button for 2  
seconds or longer switches the simple operation  
display.  
Selecting the TV mode  
1. Press the [SRC] button to select the TV  
mode.  
a/d  
Each press of the [SRC] button switches the  
mode as follows:  
TV1  
MANU  
Radio CD/MP3 (CD changer) ➜  
(DVD changer) (TV) AUX Radio...  
P.CH  
pm  
2:45  
3ch  
P1  
PRESET  
BAND  
PS AS  
DISP  
The mode of equipment that is not  
connected is not displayed.  
Channel display  
3ch: The channel currently being received is  
displayed.  
Switching the reception band  
Touching  
or  
in the standard  
1. Touch [BAND] to switch the reception band.  
Each touch of [BAND] switches the  
reception band.  
operation display allows you to perform seek  
tuning or manual tuning.  
Title display  
The name of the station currently being received  
is displayed.  
TV1 TV2 TV1...  
VTR : In video mode  
Touching these switches the display.  
38  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV Operations  
Seek tuning  
Preset memory  
Seek tuning is a function for automatically  
tuning stations with good reception.  
A total of 12 TV stations can be stored (6-TV1  
and 6-TV2). This allows you to select your  
favorite TV stations and store them in memory  
for later recall.  
1. Touch and hold [BAND] for 1 second or  
longer while “MANU” is displayed.  
Automatic tuning is possible when “SEEK” is  
displayed.  
1. Touch [BAND] to switch the reception band.  
2. Operate the channel display to select the  
station to store to.  
2. Touch  
on the channel display.  
SEEK UP/SEEK DOWN” is displayed, and  
tuning starts.  
Tuning automatically stops at stations with  
good reception.  
3. Touch [PRESET].  
The preset memory No. list is displayed.  
4. Touch and hold the preset No. to store for 2  
seconds or longer.  
You will hear a long beep, and the station is  
stored in memory.  
To cancel tuning  
1. Touch  
on the channel display again.  
Auto store  
Manual tuning  
Auto store selects 6 TV stations automatically  
and stores each one into preset memory.  
There are 2 ways available: quick tuning and  
step tuning.  
1. Touch and hold [PS/AS] for 2 seconds or  
longer.  
In the step tuning mode, the frequency changes  
1 step at a time. In the quick tuning mode, you  
can quickly tune the desired frequency.  
A-STORE” appears on the display.  
Stations with good reception are  
automatically searched, and are stored to  
preset memory (No.1 to No.6) in order  
from the station having the lowest  
frequency.  
1. Touch and hold [BAND] for 1 second or  
longer if “SEEK” is displayed.  
Manual tuning is possible when “MANU” is  
displayed.  
2. Operate the channel display to tune to a  
channel on which there is a broadcast.  
Step tuning  
Notes:  
• When auto store is performed, stations stored to  
memory so far are cleared.  
Touch  
Quick tuning  
Touch  
stops when you take your finger away from  
the panel.  
on the channel display.  
• When there are fewer than 6 stations with good  
reception, low frequencies are automatically  
returned to, and auto store is performed again. If  
there are fewer than 6 stations even after auto  
store is performed twice, stations stored so far  
remain in memory.  
on the channel display. Tuning  
Recalling a preset station  
Preset scan  
This function allows the user to select a preset  
station.  
Preset scan is a function for receiving stations in  
the order that they are currently stored to preset  
No. so that broadcasts can be checked.  
1. Touch [PRESET].  
The preset memory No. list is displayed.  
1. Touch [PS/AS].  
2. Touch the preset memory No.  
P-SCAN” appears on the display.  
The currently stored stations are received  
in order for 7 seconds or longer each.  
Stations with poor reception are skipped,  
and the next station is received.  
The station can also be tuned by touching  
in the standard operation display.  
To cancel tuning  
1. Touch [RTN].  
DXZ866MP  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TV Operations  
To cancel the preset scan  
Setting the TV Diver  
You can change the reception setting for the TV  
antenna connected to the TV tuner.  
1. Touch [PS/AS].  
P-SCAN” disappears, and the stations that  
were being received when [PS/AS] was  
touched are received next.  
• Set this item to “OFF” when a TV diversity  
antenna is not in use.  
• The factory default setting is “ON”.  
1. Press the [ADJ] button to set to the adjust  
Watching a video  
mode.  
The TV tuner has a VTR input terminal to which  
1 external device can be connected. Connect a  
12 V video cassette player (VCP) or video  
cassette recorder (VCR) to the TV tuner input  
terminal.  
2. Touch [TUNER].  
3. Touch  
on the left of the display to  
select [TV DIVER].  
ADJ TUNER  
1. Press the [MODE] button.  
TV DIVER  
ON  
2. Touch [TV/VTR].  
RTN  
Every time you touch this, the function  
switches between TV and VTR.  
4. Touch  
on the right of the display to  
select [ON] or [OFF].  
5. Press the [ADJ] button to return to the  
Setting the TV area  
(TV AREA)  
original mode.  
When you select the TV area (TV reception  
area), the TV tuner area setting changes.  
1. Press the [ADJ] button to set the adjust  
mode.  
2. Touch [TUNER].  
3. Touch  
on the left of the display to  
select “TV AREA”.  
ADJ TUNER  
TV AREA  
******  
RTN  
4. Touch  
on the right of the display to  
select the area.  
5. Press the [ADJ] button to return to the  
previous mode.  
The above operations are required when a  
TV tuner other than TTX7501z is connected.  
40  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. IN CASE OF DIFFICULTY  
Problem  
Cause  
Fuse is blown.  
Measure  
Power does not  
turn on.  
Replace with a fuse of the same amperage. If the  
fuse blows again, consult your store of purchase.  
(No sound is  
produced.)  
Incorrect wiring.  
Consult your store of purchase.  
No audio when  
Amplifier turn-on lead is  
Turn the unit off and check each wire for a possible  
short. If the amplifier turn-on lead shorts out, cover it  
operating the unit shorted to ground or  
with amplifiers.  
excessive current is required. with insulation such as tape.  
Reset button  
Nothing happens The microprocessor has  
when buttons are malfunctioned due to noise,  
Turn off the power, then  
remove the DCP by  
referencing "Removing  
the DCP" (cf. page 10).  
Press the reset button for  
about 2 seconds with a  
thin rod.  
pressed.  
etc.  
Display is not  
accurate.  
DCP or main unit connectors Wipe the dirt off with a soft cloth moistened with  
are dirty.  
cleaning alcohol.  
No sound heard. The speaker protection  
circuit is operating.  
1. Check the speaker connection.  
2. Turn down sound volume. Function can also be  
restored by turning the power off and on again.  
3. If the sound is muted again, consult your store of  
purchase.  
No sound heard. There is a disc other than a  
compact disc or foreign  
With the SLOPING CONSOLE open, press and hold  
the [Q] button for 3 seconds or longer.  
matter already in place.  
The foreign matter is forcibly ejected.  
MP3/WMA files are absent in Write MP3/WMA files onto the disc properly.  
a disc.  
Files are not recognized as  
an MP3/WMA file.  
Use MP3/WMA files encoded properly.  
File system is not correct.  
Use ISO9660 level 1, 2 or JOLIET or Romeo file  
system.  
Sound skips or is Disc is dirty.  
Clean the disc with a soft cloth.  
noisy.  
Disc is heavily scratched or  
warped.  
Replace with a disc with no scratches.  
Sound is cut or  
skipped.  
Noise is  
MP3/WMA files are not  
encoded properly.  
Use MP3/WMA files encoded properly.  
generated or  
noise is mixed  
with sound.  
DXZ866MP  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Problem  
Cause  
Measure  
Water droplets may form on  
the internal lens when the  
car is parked in a humid  
place.  
Let dry for about 1 hour with the power on.  
Sound is bad  
directly after  
power is turned  
on.  
File system is not correct.  
Use ISO9660 level 1, 2 or JOLIET or Romeo file  
system.  
Wrong filename  
File name or extension is not Use alphanumeric/ASCII characters for MP3/WMA  
Play list play is  
not performed.  
correct.  
file name.  
Use “.M3U” for the file extension of a play list.  
42  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10. ERROR DISPLAYS  
If an error occurs, one of the following displays is displayed.  
Take the measures described below to eliminate the problem.  
Error Display  
ERROR 2  
Cause  
Measure  
A DISC is caught inside the CD deck and is  
not ejected.  
This is a failure of CD deck’s mechanism and  
consult your store of purchase.  
ERROR 3  
ERROR 6  
ERROR 2  
ERROR 3  
ERROR 6  
ERROR 2  
ERROR 3  
ERROR 6  
A DISC cannot be played due to scratches,  
etc.  
Replace with a non-scratched,  
non-warped-disc.  
A DISC is loaded upside-down inside the  
CD deck and does not play.  
Eject the disc then reload it properly.  
A DISC inside the CD changer is not  
loaded.  
This is a failure of CD changer’s mechanism  
and consult your store of purchase.  
A DISC inside the CD changer cannot be  
played due to scratches, etc.  
Replace with a non-scratched, non-warped  
disc.  
A DISC inside the CD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly.  
A DISC inside the DVD changer cannot be  
played.  
This is a failure of DVD mechanism and con-  
sult your store of purchase.  
A DISC cannot be played due to scratches,  
etc.  
Retry or replace with a non-scratched, non-  
warped-disc.  
A DISC inside the DVD changer cannot be  
played because it is loaded upside-down.  
Eject the disc then reload it properly  
Set the correct Parental level.  
ERROR P  
ERROR R  
Parental level error  
Region code error  
Eject the disc and replace correct region  
code disc.  
AMP GUARD  
The speaker protection circuit is operating.  
During this operation, if any volume  
operation is performed, the display shows  
AMP GUARD”.  
AMP GUARD” sometimes functions when  
special test signals are used.  
1. Turn down sound volume. Function can  
also be restored by turning the power off  
and on again.  
(Speaker volume is reduced automatically  
when the speaker protection circuit oper-  
ates).  
2. If the sound is muted again, consult our  
service department.  
If an error display other than the ones described above appears, press the reset button. If the problem  
persists, turn off the power and consult your store of purchase.  
DXZ866MP  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11. SPECIFICATIONS  
FM Tuner  
Frequency Range:  
Audio  
Maximum Power Output:  
87.0 MHz to 108.0 MHz  
212 W (53 W × 4 ch)  
Usable Sensitivity:  
9 dBf  
Continuous Average Power Output:  
18 W × 4, into 4 , 20 Hz to 20 kHz, 1%THD  
50dB Quieting Sensitivity:  
15 dBf  
Bass Control Action:  
+16, –12 dB  
Alternate Channel Selectivity:  
70 dB  
Treble Control Action:  
12 dB  
Stereo Separation (1 kHz):  
32 dB  
Line Output Level (CD 1 kHz):  
4 V/F 2ch + 4V/R 2ch  
4 V/SUB WOOFER 2ch  
Frequency Response ( 3 dB):  
30 Hz to 15 kHz  
General  
Power Supply Voltage:  
14.4 V DC (10.8 to 15.6 V allowable), negative  
ground  
AM Tuner  
Frequency Range:  
531 kHz to 1629 kHz  
Current Consumption:  
Less than 15 A, 3A  
Usable Sensitivity:  
25 µV  
Speaker Impedance:  
4 (4 to 8 allowable)  
Weight / Source unit:  
3.74 lb. (1.7 kg)  
CD Player  
System:  
Compact disc digital audio system  
Weight / Remote control unit:  
1.41 oz. (40 g) (including battery)  
Usable Discs:  
Compact disc  
Dimensions / Source unit:  
7" (Width) × 2" (Height) × 6-5/16" (Depth)  
[178 (W) × 50 (H) × 160 (D) mm]  
Dimensions / Remote control unit:  
1-3/4" (Width) × 4-7/16" (Height) × 1/2" (Depth)  
[44 (W) × 113 (H) × 13 (D) mm]  
Frequency Response ( 1 dB):  
5 Hz to 20 kHz  
Signal to Noise Ratio (1 kHz):  
100 dB  
Dynamic Range (1 kHz):  
96 dB  
Harmonic Distortion:  
0.01%  
Note:  
• Specifications and design are subject to change without notice for further improvement.  
44  
DXZ866MP  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Clarion Co., Ltd.  
PE-2697K  
280-8350-00  
2006/1 (Abe·Abe)  
All Rights Reserved. Copyright © 2006: Clarion Co., Ltd.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Continental Electric Rice Cooker CE23201 User Manual
Cuisinart Mixer HM 50 User Manual
Curtis Flat Panel Television LCD2424A User Manual
Delta Electronics Power Supply Series S48SS User Manual
Dynacord Portable Speaker LITTLEMAX User Manual
Eagle Electronics SONAR 2T User Manual
Earlex Ventilation Hood VAP75 User Manual
Electro Voice Portable Speaker DL18X User Manual
Frigidaire Cooktop FPEC3685K User Manual
Gefen Cable Box GEF HDMI13 2 3GSDI User Manual