Owner’s manual
Mode d’emploi
Manual de instrucciones
DRX9675z
FM/AM CD PLAYER WITH CD/MD CHANGER
CONTROL/AC PROCESSOR
•
LECTEUR CD FM/AM AVEC COMMANDE DE
CHANGEUR CD/MD/PROCESSEUR AC
•
RADIO DE FM/AM CON REPRODUCTOR DE
DISCOS COMPACTOSY CONTROLADOR DE
CAMBIADOR DE DISCOS CD/MD/
PROCESADOR AC
Clarion Co., Ltd.
PE-2319B
280-7478-00
All Rights Reserved. Copyright © 2000: Clarion Co., Ltd.
Printed in China / Imprimé au Chine / Impreso en China
T E X T
2000/5 (A·C)
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Compact Discs
6. REMOTE CONTROL
2. PRECAUTIONS
Use only compact discs bearing the
mark.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
1. When the inside of the car is very cold and
the player is used soon after switching on
the heater moisture may form on the disc or
the optical parts of the player and proper
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft cloth.
If moisture forms on the optical parts of the
player, do not use the player for about one
hour.The condensation will disappear natu-
rally allowing normal operation.
Do not play heart-shaped, octagonal, or other specially shaped compact discs.
Some CDs recorded in CD-R mode may not be usable.
Even when recorded in CD-R/W mode, some CDs not be usable.
Receiver for remote control unit
3. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
• To remove a compact disc from its storage case,
press down on the center of the case and lift the
disc out, holding it carefully by the edges.
• Do not use commercially available CD protec-
tion sheets or discs equipped with stabilizers,
etc. These may damage the disc or cause
breakdown of the internal mechanism.
Handling
• New discs may have some roughness around
the edges. If such discs are used, the player
may not work or the sound may skip.Use a ball-
point pen or the like to remove any roughness
from the edge of the disc.
Operating range: 30˚ in all directions
Ball-point pen
Signal transmitter
Storage
Roughness
• Do not expose compact discs to direct sunlight
or any heat source.
• Do not expose compact discs to excess hu-
midity or dust.
• Do not expose compact discs to direct heat
from heaters.
Remote control unit
This equipment has been tested and found to
comply with the limits for a Class B digital de-
vice, pursuant to Part 15 of the FCC Rules.
CAUTION
USE OF CONTROLS, ADJUSTMENTS, OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN, MAY RE-
SULT IN HAZARDOUS RADIATION EXPO-
SURE.
These limits are designed to provide reason-
able protection against harmful interference in
a residential installation.
• Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
• Never play a compact disc with any cellophane
tape or other glue on it or with peeling off marks.
If you try to play such a compact disc, you may
not be able to get it back out of the CD player
or it may damage the CD player.
• Do not use compact discs that have large
scratches, are misshapen, cracked, etc. Use of
such discs may cause misoperation or damage.
Cleaning
This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio com-
munications. However, there is no guarantee
that interference will not occur in a particular
installation.
THE COMPACT DISC PLAYER SHOULD NOT
BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE
PERSONNEL.
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the center
of the compact disc to the circumference.
• Do not use any solvents, such as commercially
available cleaners, anti-static spray or thinner
to clean compact discs.
CHANGES OR MODIFICATIONS NOT EX-
PRESSLY APPROVED BY THE MANUFAC-
TURER FOR COMPLIANCE COULDVOIDTHE
USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
• After using special compact disc cleaner, let
the compact disc dry off well before playing it.
If this equipment does cause harmful interfer-
ence to radio or television reception, which can
be determined by turning the equipment off and
on, the user is encouraged to consult the dealer
or an experienced radio/TV technician for help.
Sloping Console
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE MANU-
FACTURERWILLVOIDTHEWARRANTY AND
WILL VIOLATE FCC APPROVAL.
This unit uses sloping consoles to make large-screen displays possible.
3. If you move the SLOPING CONSOLE by
CAUTION
Be careful not to get your fingers caught when
opening and closing the SLOPING CONSOLE.
hand, this may create play.To correct this play,
with the power on for the unit, press ANGLE
button 6 to close the SLOPING CONSOLE.
Inserting the Batteries
MODEL
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
12V
GROUND
4. After a CD is ejected, the SLOPING CON-
SOLE automatically returns to the tilted or
closed state. If there is any obstruction when
the SLOPING CONSOLE tries to close, the
safety mechanism is triggered and the SLOP-
ING CONSOLE returns to the open state. If
this happens, remove the obstruction, then
press OPEN button 6 or ANGLE button 6 .
AA (UM-3/1.5V)
Batteries
AM 530-1710kHz/FM 87.9-107.9MHz
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE TAHT MAY CAUSE UNDESIRED
OPERATION.
2. Insert the AA (UM-3/1.5V) batteries that
came with the remote control unit facing in
the directions shown in the figure, then close
the rear cover.
1. For safety’s sake, always close the SLOPING
CONSOLE before leaving this unit unused for
a prolonged period or switching OFF the igni-
tion key.
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
CLARION CO.,LTD.
50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN
Notes:
If you switch OFF the ignition key with the
SLOPING CONSOLE tilted, the SLOPING
CONSOLE does not close.
Rear cover
Using batteries improperly can cause them to explode.
Take note of the following points:
• When replacing batteries, replace both batteries with
051 722 877
MANUFACTURED:
2. Before the SLOPING CONSOLE closes, there
may be a braking sound from the safety
mechanism. This is normal.
new ones.
Rear side
286-
Clarion Co.,Ltd.
MADE IN
SERIAL No.
PE-
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
Bottom View of Source Unit
Be sure to unfold and read the next page.
Veuillez déplier et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
8
DRX9 6 7 5 z
DRX9 6 7 5 z
3
DRX9 6 7 5 Rz
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. CONTROLS / LES COMMANDES / CONTROLES
4. NOMENCLATURE
5. DCP
Note:
The control panel can be detached to prevent theft. When detaching the control panel, store it in the
DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).
Source unit / Appareil pilote / Unidad fuente
We recommend taking the DCP with you when leaving the car.
Names of Buttons
Removing the DCP
1. With the SLOPING CONSOLE closed, turn
off the power.
Attaching the DCP
1
2
3
4
5
6
Release button
VOLUME button
DISP (display) button
SEARCH button
ISR (instant station recall) button
OPEN button
9
!
POWER OFF button
Shift button
1. Insert the DCP so that the A section on the
right side of the DCP catches on the hook B
on the unit.
"
Preset buttons (1 to 6)
Direct buttons (1 to 6)
TITLE button
2. Press the Release button 1 deeply to open
the DCP.
#
$
ENT (enter) button
Play/pause button
MUTE button
Eject button
ANGLE button
%
&
(
7
8
POWER button
FUNCTION button
BAND button
MODE button
CD insertion slot
With the SLOPING CONSOLE opened / Ouvrez la CONSOLE RABATTABLE /
Apertura de la CONSOLA INCLINABLE
3. Pull the DCP toward you and remove it.
2. Press the left side of the DCP carefully to fit it
in place.
TOP button
DCP
Display Items (Function mode)
CAUTION
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it
or subject it to strong shocks.
1
2
Function icon
• in CD Mode (CD TEXT):
• in Radio Mode: ST indication
• in CD Changer Mode: CD Changer No.
• in MD Changer Mode: MD Changer No.
• in TV Mode: ST or MONO, MAIN, SUB
• in Radio Mode:
USER, DISC, ARTIST, TRACK
• in CD Changer Mode (CD TEXT):
USER, DISC, ARTIST, TRACK
• in MD Changer Mode: TRACK, DISC
• in TV Mode: MANU (manual) indication
• in Radio Mode:
• If the Release button 1 is pressed and the
DCP is not locked into place, it may fall out
from vibration of the car.This can break the
DCP, so after removing it, either install it on
the unit or put it in its DCP case.
3
AS (auto store) or SCN (scan)
• in CD Mode:
5
CAUTION
• Always close the SLOPING CONSOLE be-
Band, programme type, frequency, etc.
• in CD Mode:
• The connector connecting the unit and the
DCP is an extremely important part. Be care-
ful not to damage it by pressing on it with
fingernails, screwdrivers, etc.
SCN (scan) or RPT (repeat), RDM (random)
• in CD Changer Mode:
fore removing the DCP.
Track no., play time, user title, etc.
• in CD Changer Mode:
• If you remove the DCP with the SLOPING
CONSOLE open, the SLOPING CONSOLE
closes immediately. Be careful not to get
your fingers caught.
Display / Afficheur / Visualizador
SCN (scan) or RPT (repeat), RDM (random),
D-SCN (disc scan), D-RPT (disc-repeat),
D-RDM (disc random)
Track no., play time, user title, CD-TEXT, etc.
• in MD Changer Mode:
Note:
• If the DCP is dirty, wipe off the dirt with a soft, dry
• in MD Changer Mode:
Track no., play time, MD title, etc.
• in TV Mode:
cloth only.
AC-1
RP T
DIS C
SCN (scan) or RPT (repeat), RDM (random),
D-SCN (disc scan), D-RPT (disc-repeat),
D-RDM (disc random)
Band, channel no., user title, etc.
P.ch (preset channel) or Sub indication
Preset channel indication
A B C
6
7
D2 T0 1 0 0 :0 0
• inTV Mode: AS (auto store) or SCN (scan)
• in Radio Mode: MANU (manual) indication
1
2
3
4
5
6
Dis c
4
Sub menu indication
LCD Screen
1. In extreme cold, the screen movement may
slow down and the screen may darken, but
this is normal. The screen will recover when
it returns to normal temperature.
2. The colors displayed on the LCD screen vary
with the heat of this unit and the tempera-
ture in the car.This is a characteristic of LCDs
and is normal. The display colors return to
normal when the LCD screen returns to
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
normal temperature.
5
DRX9 6 7 5 z
6
DRX9 6 7 5 z
DRX9 6 7 5 z
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Functions of Remote Control Unit Buttons
CD changer
MD changer
Mode
Radio
CD
TV
Button
,
FUNC
POWER
Turns power on and off. When pressed and held for 1 second: Turns power off.
Switches among radio, CD, CD changer, MD changer and TV.
-
BAND
DISC UP
PROG
TOP
Plays the first track. Moves the next disc
Switches reception
band.
Switches reception
band.
Top play.
in increasing order.
Increases and decreases volume (in all modes).
.
VOLUME
SEARCH
/
Moves preset
channels up and
down.
Moves tracks up
and down.
When pressed and When pressed and down.
Moves tracks up
and down.
Moves preset
channels up and
held for 1 second:
Fast-forward/
fast-backward.
held for 1 second:
Fast-forward/
fast-backward.
:
PLAY/PAUSE
No function.
Switches between
Switches between
No function.
playback and pause. playback and pause.
Turns mute on and off.
;
MUTE
ISR
<
Recalls ISR radio station in memory.
Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio
mode only).
=
>
Switches among main display, sub display, clock display and spectrum analyzer
display.
DISP
Preset scan.
Scan play.
Scan play.
When pressed and When pressed and
held for 2 seconds: held for 2 seconds:
Preset scan.
SCN
PS/AS
When pressed and
held for 2 seconds:
Auto store.
Disc scan play.
Auto store.
?
No function.
Repeat play.
Random play.
Repeat play.
No function.
RPT
BLS
When pressed and
held for 2 seconds:
Disc repeat play.
@
No function.
Random play.
Switches between
RDM
When pressed and TV and VTR.
held for 2 seconds:
Disc random play.
DOLBY NR
MONI
* Some of the corresponding buttons on the source unit and remote control unit have different functions.
DRX9 6 7 5 z
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Adjusting the balance
1. Press MODE button & three times and select
“BAL DETAIL”.
7. OPERATIONS
Once selected, the preferred display becomes
the display default. When a function adjustment
such as volume is made, the screen will
momentarily switch to that function’s display,
then revert back to the preferred display sev-
eral seconds after the adjustment.
If a title has been input, it is displayed in the main
display. If no title has been input, “------------”
appears in the display. To input a title, refer to
the subsection in “Entering titles” in “Other
Handy Functions” section.
Note: Be sure to read this chapter referring to the front diagrams of
Basic Operations
chapter “3. CONTROLS” on page 5 (unfold).
2. Press the right side of SEARCH button 4 to
select “0”.
2. Each time you press FUNCTION button 7 ,
CAUTION
the mode of operation changes in the following
order:
3. Pressing VOLUME button 2 up (w) empha-
sizes the sound from the right speaker;
pressing it down (z) emphasizes the sound
from the left speaker.
Be sure to lower the volume before switch-
ing off the unit power or the ignition key.The
unit remembers its last volume setting. If you
switch the power off with the volume up, when
you switch the power back on, the sudden
loud volume may hurt your hearing and dam-
age the unit.
Radio (TUNER) mode ➜ CD mode ➜ CD
changer mode ➜ MD changer mode ➜ TV
mode ➜ Radio (TUNER) mode...
External equipment not connected with CeNET
is not selected.
The factory default setting is “0”. (Adjustment
range: LEFT13 to RIGHT13)
4. When the adjustment is complete, press
MODE button & several times or press and
hold ENT button $ for 1 second or longer until
the function mode is reached.
Changing the angle of the SLOPING
CONSOLE
If the installation position or display angle makes
the display hard to see, change the angle of the
SLOPING CONSOLE.
The clock is displayed when the ignition key
is turned to the ACC (accessory) or IGN (igni-
tion-on) position even when the unit power
is off. In some cars, the clock may momen-
tarily disappear when the ignition key is
turned to the START position. The clock will
reappear after the engine has started and the
ignition key is released to the IGN (ignition-
on) position.
Adjusting the volume
Pressing VOLUME button 2 up (w) increases
the volume; pressing it down (z) decreases the
volume.
Adjusting the fader
1. Press MODE button & three times and select
“FAD DETAIL”.
1. Press and hold OPEN (ANGLE) button 6 for
The volume level is from 0 (minimum) to 33 (maxi-
mum).
2 seconds or longer.
2. Each time this button is pressed, the
SLOPING CONSOLE switches to the tilted or
closed state.
2. Press the right side of SEARCH button 4 to
select “0”
Switching the display
Press DISP button 3 to select the desired display.
Each time you press DISP button 3 , the display
switches in the following order:
3. Pressing VOLUME button 2 up (w) empha-
sizes the sound from the front speakers;
pressing it down (z) emphasizes the sound
from the rear speakers.
Turning on/off the power
Note:
• Be careful about using this unit for a long time with-
out running the engine. If you drain the car’s bat-
tery too far, you may not be able to start the en-
gine and this can reduce the service life of the
battery.
CAUTION
When not using this unit for a long time and
when turning OFF the ignition key for the car,
close the SLOPING CONSOLE for safety’s sake.
Main display
The factory default setting is “0”. (Adjustment
range: FRONT12 to REAR12)
MANU
F M 1 B B C
4. When the adjustment is complete, press
MODE button & several times or press and
hold ENT button $ for 1 second or longer until
the function mode is reached.
F
M
1
8 0 . 0
Switching the screen saver
You can switch between 3 screen savers.
1
2
3
4
5
6
P.ch
1. Press POWER button 7 .
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
1. Press DISP button 3 and select the screen
Clock display
saver display.
MANU
2. Each time you press and hold DISP button
F M 1 B B C
F
M
1
PM 7 : 5 0
3
for 1 second or longer, the screen saver
changes between 3 screen savers.
3. Press and hold POWER button 7 for 1 sec-
ond or longer to turn off the power for the unit
or press POWER OFF button 9 .
1
2
3
4
5
6
P.ch
Spectrum analyzer
display
Adjusting the EXTRA output volume
Note:
You can adjust the volume output from the unit’s
• About the system check
non-fader output terminal.
The confirmation of connected equipments must
be performed for this unit only when the wiring
connection is complete and power is turned on to
the unit first. When the power is supplied,
“SYSTEM CHECK” appears in the display. Press
POWER button 7 . The system check starts inside
the unit. The equipments connected to this unit
appears in the display. Press POWER button 7
again.
1. Press MODE button
&
three times and select
“EXTRA VOL” while in Audio Mode.
2. Press the right side of SEARCH button
4
to
Screen saver display
select “0”.
3. Pressing VOLUME button 2 up (w) increases
the output volume; pressing it down (z)
decreases the output volume.
The factory default setting is “0”. (Setting range:
–5 to +5)
Selecting a mode
1. Press FUNCTION button 7 to change the
4. When the adjustment is complete, press MODE
button & several times or press and hold ENT
button $ for 1 second or longer until the function
mode is reached.
mode of operation.
Main display...
10
DRX9 6 7 5 z
DRX9 6 7 5 z
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Radio Operations
CD Operations
Radio Operations
FM Reception
For enhanced FM performance the
tuner includes signal actuated stereo control,
Enhanced Multi AGC, Impulse noise reduction
curcuits and Multipath noise reduction circuits.
Manual tuning
There are 2 ways available: Quick tuning and step
tuning.
When you are in the step tuning mode, the frequency
changes one step at a time. In quick tuning mode, you
can quickly tune the desired frequency.
Auto store
Loading a CD
1. Press OPEN button 6 . The SLOPING
®
Auto store is a function for storing up to 6 stations
that are automatically tuned in sequentially. If 6
receivable stations cannot be received, a
previously stored station remains unoverwritten
at the memory position.
CONSOLE opens.
.
CAUTION
Be careful not to get your fingers caught when
opening and closing the SLOPING CONSOLE.
Changing the reception area
1. Press BAND button 8 and select the desired
1. Press BAND button 8 and select the desired
band. (FM or AM)
band. (FM or AM)
2. Insert a CD into the center of the insertion
slot with the label side facing up.The CD plays
automatically after loading.
This unit is initially set to USA frequency intervals
of 10 kHz for AM and 200 kHz for FM. When using
it outside the USA, the frequency reception range
can be switched to the intervals below.
If “MANU” is not lit in the display, press and
hold BAND button 8 for 1 second or longer.
“MANU” is lit in the display and manual tuning
is now available.
2. Press the Shift button ! to display the
subdisplay.
Notes:
3. Press and hold the AS button
"
for 2 seconds
• Never insert foreign objects into the CD insertion
slot.
• If the CD is not inserted easily, there may be
another CD in the mechanism or the unit may
require service.
or longer. The stations with good reception
are stored automatically to the preset
channels.
➜➜Setting the reception area
2. Tune into a station.
1. Press BND button 8 and select the desired
➜ Quick tuning:
radio band (FM or AM).
Press and hold the right or left side of
SEARCH button 4 for 1 second or longer to
tune in a station.
If auto store is performed in the FM bands, the
stations are stored in FM3 even if FM1 or FM2
was chosen for storing stations.
2. While pressing DISP button 3, each time you
press and hold the number “6” of the Preset
• Discs not bearing the
mark and CD-ROMs
buttons
"
for 2 seconds or longer, the recep-
➜ Step tuning:
cannot be played by this unit.
tion area switches from inside the USA to
outside the USA or from outside the USA to
inside the USA.
Preset scan
Preset scan receives the stations stored in pre-
set memory in order.This function is useful when
searching for desired station in memory.
Press the right or left side of SEARCH button
4
to manually tune in a station.
Loading 3" (8 cm) compact discs
Any station preset memories are lost when the
reception area is changed.
No adapter is required to play a 3" CD.
Insert the 3" CD into the center of the insertion slot.
3. After loading a CD, the SLOPING CONSOLE
closes automatically.
Recalling a preset station
1. Press the Shift button !
to display the
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exist to store individual radio stations
in memory. Pressing the corresponding preset
button recalls the stored radio frequency
automatically.
subdisplay.
Listening to the radio
1. Press FUNCTION button 7 and select the
2. Press the PS button
"
.
Notes:
radio mode. The frequency is displayed.
3. When the desired station is tuned in, press
• Note that SLOPING CONSOLE close immediately
after a CD is inserted into CD insertion slot.
• If no CD is loaded in the SLOPING CONSOLE, it
closes after 30 seconds.
the PS button
that station.
"
again to continue receiving
2. Press BAND button 8 and select the radio
band. Each time the button is pressed, the radio
reception band changes in the following order:
1. Press BAND button 8 and select the desired
band. (FM or AM)
FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1...
2. Press the Shift button ! to display the preset
Listening to a CD already inserted
channel display.
3. Press the right or left side of SEARCH button
Press FUNCTION button 7 to select the CD
mode. Play starts automatically. If no CD is
loaded in the unit, “NO DISC” appears in the
display.
4
to tune in the desired station.
3. Press the corresponding Preset button
recall the stored station.
"
to
Press and hold one of Preset buttons
"
for 2
Tuning
seconds or longer to store that station into
preset memory.
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
Pausing play
1. Press Play/pause button $ to pause play.
“PAUSE” appears in the display.
Manual memory
1. Press BAND button 8 and select the desired
Seek tuning
1. Press BAND button 8 and select the desired
2. To resume CD play, press Play/pause button
band. (FM or AM)
band. (FM or AM)
$
again.
2. Press the Shift button ! to display the preset
If “MANU” is lit in the display, press and hold
BAND button 8 for 1 second or longer.
“MANU” in the display goes off and seek tuning
is now available.
channel display.
3. Select the desired station with seek tuning,
manual tuning, or preset tuning.
2. Press the right or left side of SEARCH button
4. Press and hold one of Preset buttons
"
for 2
4
to automatically seek a station.
seconds or longer to store the current station
into preset memory.
When the right side of SEARCH button 4 is
pressed, the station is sought in the direction
of higher frequencies; if the left side of
SEARCH button 4 is pressed, the station is
sought in the direction of lower frequencies.
12
DRX9 6 7 5 z
DRX9 6 7 5 z
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Handy Functions
CD Operations
Ejecting a CD
pressing Direct buttons
"
(1 to 5).
Setting the clock
Top function
1 ... Capital letters
2 ... Small letters
3 ... Numbers/symbols
4 ... Umlauts
1. Press MODE button & four times to display
1. Press the Eject button 6 . The SLOPING
CONSOLE opens and a CD ejects. “EJECT”
appears in the display.
The top function resets the CD player to the first
track of the disc. Press TOP button 8 to play
the first track (track No. 1) on the disc.
the adjustment selection display.
2. Press up (w) or down (z) of VOLUME
buttons 2 and select “CLOCK”.
5 ... Title clear
6. Press VOLUME buttons 2 up (w) or down
Scan play
CAUTION
Be careful not to get your fingers caught when
opening and closing the SLOPING CONSOLE.
3. Press the right side of SEARCH button 4 to
“CLOCK” appears in the display.
(z) to select the character to enter.
The scan play locates and plays the first 10 sec-
onds of each track on a disc automatically. This
function continues on the disc until it is canceled.
7. Repeat steps 4 to 6 to enter for the title.
4. Press the right side or left side of SEARCH
8. Press and hold ENT button $ for 2 seconds
or longer to store the title into memory and
cancel title input mode.
button 4 to select the hour or the minute.
2. Remove the CD and press OPEN button 6
The scan play is useful when you want to select a
desired track.
5. Press the up (w) or down (z) of VOLUME
to close the SLOPING CONSOLE.
2
button to set the correct time.
Notes:
1. Press the SCN button
“SCN” lights in the display.
2. To cancel the scan play, press the SCN button
again.“SCN” goes off from the display and
"
to start scan play.
The clock is displayed in 12-hour format.
• Be sure to close the SLOPING CONSOLE after
Clearing titles
removing the CD.
6. Press ENT button $ to store the time into
1. Select and play a CD or CD in the CD changer
or tune in to a radio station or a TV station for
which you want to clear the title.
• The SLOPING CONSOLE closes automatically 30
seconds after removing the CD.
memory.
"
7. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
the current track continues to play.
If a CD (12 cm) is left in the ejected position for 15
seconds, the CD is automatically reloaded. (Auto
reload)
3" CDs (8 cm) are not auto reloaded. Be sure to
remove it when ejected.
2. When you press and hold TITLE button #
for 1 second or longer, the display switches
to the title input screen.
Repeat play
Note:
The repeat play continuously plays the current
track. This function continues automatically until
it is canceled.
•
You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the car’s
battery or take out this unit, the clock is reset. While
setting the clock, if another button or operation is
selected, the clock set mode is canceled.
3. Press the CLR button
"
.
Notes:
4. If you press and hold ENT button $ for 2
seconds or longer, the title is cleared and title
input mode is cancelled.
• If you force a CD into before auto reloading,
this can damage the CD.
1. Press the RPT button
"
. “RPT” lights in the
display and the current track is repeated.
2. To cancel the repeat play, press the RPT
Selecting a track
➜➜Track-up
Entering titles
Title list play
You can display a list of titles, then select the disc
or broadcast station to listen to from that list.
button
"
again. “RPT” goes off from the
Titles up to 10 characters long can be stored in
memory and displayed for radio stations and TV
stations and CDs. The numbers of titles that can
be entered for each mode are as follows.
display and normal play resumes.
1. Press the right side of SEARCH button 4 to
move ahead to the beginning of the next track.
Random play
1. With the unit in radio, CD/MD changer, TV
2. Each time you press the right side of SEARCH
button 4 , the track advances ahead to the
beginning of the next track.
The random play selects and plays individual
tracks on a disc in no particular order. This
function continues automatically until it is
canceled.
mode, press TITLE button # .
Mode
Number of titles
30 titles
2. Press BAND button 8 and switch to the band
or disc you want to play.
Radio mode
CD mode
TV mode
➜➜Track-down
50 titles
3. Press the right or left side of SEARCH button
1. Press the left side of SEARCH button 4 to
1. Press the RDM button
"
. “RDM” lights in the
4
and select the desired title.
15 titles
move back to the beginning of the current track.
display, an individual track is selected
randomly and play begins.
4. When you press ENT button $ , the broadcast
CD changer mode
CDC655z connected
CDC655Tz connected
CDC1255z connected
Number of titles
60 titles
2. Press the left side of SEARCH button 4 twice
or disc of which title you selected starts.
to move to the beginning of the previous track.
2. To cancel the random play, press the RDM
button
"
again. “RDM” goes off and normal
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
100 titles
Fast-forward/fast-backward
➜➜Fast-forward
play resumes.
50 titles
1. Press FUNCTION button 7 to select the
mode you want to enter a title. (Radio, CD,
CD changer or TV)
Press and hold the right side of SEARCH button
The factory default setting is “8”. (Adjustment level:
1 to 15)
4
for 1 second or longer.
1. Press MODE button & four times to switch
➜➜Fast-backward
2. Select and play a CD or a CD in the CD
changer or tune in to a radio station or a TV
station for which you want to enter the title.
to the adjustment selection display.
Press and hold the left side of SEARCH button
2. Press VOLUME buttons 2 up (w) or down
(z) to select “CONTRAST”.
3. Press the right side of SEARCH button 4 to
4
for 1 second or longer.
3. If you press and hold TITLE button # for 1
second or longer, the display switches to the
title input screen.
move the cursor.
4. Press VOLUME buttons 2 up (w) or down
(z) to adjust the contrast.
4. Press the right or left side of SEARCH button
4
to move the cursor.
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
5. Press one of Direct buttons
"
from “1” to “4”
and select the character you want to enter.
You can enter title characters as follows by
Download from Www.Somanuals.com. All Manuals Search And Download.
14
DRX9 6 7 5 z
DRX9 6 7 5 z
15
Other Handy Functions
Other Handy Functions
1. Press MODE button & four times to switch
Adjusting the dimmer level
You can adjust the reduced illumination level of
the dimmer.
Setting the Background Color
Setting the Method for Title Scroll
(A-SCROLL)
Title Scroll
to the adjustment selection display.
(Pattern) on the Display (BG COLOR)
2. Press VOLUME buttons 2 up (w) or down
(z) to select “EXTRA OUT”.
3. Press the right side of SEARCH button 4 to
Background Color (Pattern) on the Display
The factory default setting is “5”.
To use the dimmer, set the dimmer setting to OFF
to 5.
When the display is not showing I-BGV, a desired
background color (pattern) can be set on the
display.
Title scroll is a function for scrolling the screen to
the end of a long title not appearing in the title
box. This function works while the text title (disc
or artist of track) of CD or MD player is displayed.
move the cursor.
1. Press MODE button & four times to switch
4. Press VOLUME buttons
2
up (w) to set
The factory default setting is “BLCK” (black).
Select a desired pattern referring to the display
indication.
to the adjustment selection display.
“ON” or down (z) to set “OFF”.
➜ ON:
The factory default setting is “ON”.
1. Press MODE button & four times to select
the adjustment mode.
2. Press VOLUME buttons 2 up (w) or down
(z) to select “DIMMER LV.”.
3. Press the right side of SEARCH button 4 to
1. Press MODE button & four times to select
When you press MODE button & three times
to select Audio Mode, the “EXTRA VOL” item
is displayed.
the adjustment mode.
2. Press VOLUME buttons 2 up (w) or down
(z) to select “A-SCROLL”.
3. Press the right side of SEARCH button 4 to
move cursor.
2. Press VOLUME buttons 2 up (w) or down
(z) to select “BG COLOR”.
3. Press the right side of SEARCH button 4 to
4. Press VOLUME buttons 2 up (w) or down
(z) to adjust the reduced illumination level
of the dimmer.
The output level can be adjusted (–5~+5).
➜ OFF:
make adjustments.
move the cursor to the right.
4. Press VOLUME buttons 2 up (w) or down
(z) to select “ON” or “OFF”.
Even when you press MODE button & three
times to select Audio Mode, the “EXTRAVOL”
item is not displayed.
➜ 1 to 5:
4. Press VOLUME buttons 2 up (w) or down
(z) to select a background pattern.
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
The dimmer operation is performed
depending on the set level 1 to 5.
Every time VOLUME button 2 is pressed, the
display is switched as shown below.
The output level cannot be adjusted.
5. Press MODE button & or Press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
➜ OFF:
“ON” (The screen is scrolled automatically)
w
No dimmer operation is performed.
z
➜ Background Pattern
5. Press MODE button & or Press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
“OFF” (The screen is scrolled when the TITLE
button # is pressed and held for 1 second or
longer)
BLCK (black)
Triggered audio mute for cellular
telephones
This unit requires special wiring to mute the au-
dio signal automatically when a cellular telephone
rings in the car.
↓
BLUE (blue)
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
Message display
When the unit is powered on or off, a message is
displayed. The user can turn this message
display ON or OFF.
↓
RED (red)
↓
This function is not compatible with all cellular tele-
phones. Contact your local authorized Clarion
dealer for information on proper installation and
compatibility.
GREN (green)
Setting the button illumination.
↓
The factory default setting is “ON”.
The factory default setting is “GREN” (green).
1. Press MODE button & four times to select
the adjustment mode.
NEON (neon)
1. Press MODE button & four times to switch
to the adjustment selection display.
↓
CHEK (check)
2. Press VOLUME buttons 2 up (w) or down
(z) to select “MESSAGE”.
3. Press the right side of SEARCH button 4 to
Setting the Background Spectrum
Analyzer
Display of Background Spectrum Analyzer
(BG SPE/ANA)
2. Press VOLUME buttons 2 up (w) or down
↓
(z) to select “ILLUMI”.
COIN (coin)
3. Press the right side of SEARCH button 4 to
move the cursor to the right side.
↓
move the cursor.
ELEC (electric board)
4. Press VOLUME buttons 2 up (w) or down
(z)to select “AMBR” (amber) or “GREN”
(green).
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
↓
4. Press VOLUME buttons 2 up (w) or down
(z) to set message display ON or OFF.
5. Pressing ENT button $ returns to the
When the display is not showing I-BGV, SPE/ANA
is shown on the right side of the display.
UFO (UFO)
↓
The factory default setting is “ON”.
1. Press MODE button & four times to select
the adjustment mode.
PINK (pink)
adjustment selection display.
↓
6. Press MODE button & or Press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
SAND (sand)
2. Press VOLUME buttons 2 up (w) or down
(z) to select “BG SPE/ANA”.
3. Press the right side of SEARCH button 4 to
↓
WIND (wind)
↓
FIRE (fire)
Turning the EXTRA output
adjustment display on/off
When not using the EXTRA output, you can put
move the cursor to the right.
4. Press VOLUME buttons 2 up (w) or down
(z) to select “ON” or “OFF”.
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
out the “EXTRA VOL” display.
The factory default setting is “ON”.
Even if the level adjustment display is set to “OFF”,
signals can be output from the non-fader output.
16
DRX9 6 7 5 z
DRX9 6 7 5 z
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CD Changer Operations
8. OPERATIONS OF ACCESSORIES
CD Changer Operations
➜➜When playing a disc 1 to 6
2. When you press the RPT button
"
, repeat
play starts. “RPT” lights in the display.
1. Press the Shift button ! to display the disc
display (1 to 6).
3. To cancel repeat play, press the RPT button
"
again. “RPT” goes off from the display and the
unit returns to normal play.
2. Press Direct button
"
(1 to 6) with the same
1. Display the CD-text title (disc, artist or track).
CD changer functions
number as the CD playing.
2. Press and hold TITLE button # for 1 second
When an optional CD changer is connected
through the CeNET cable, this unit controls all
CD changer functions.This unit can control a total
of 2 changers (MD and/or CD).
➜➜When playing a disc 7 to 12 (only when a
12 disc CD changer is used.)
or longer. The title scrolls.
Disc repeat play
After all tracks in the current disc have been
played, the disc repeat play automatically replays
the current disc over from the first track. This
function continues automatically until it is
cancelled.
1. Press the Shift button ! to display the disc
Selecting a CD
display (7 to 12).
Press FUNCTION button 7 and select the CD
changer mode to start play. If 2 CD changers are
connected, press FUNCTION button 7 to select
the CD changer for play.
Each of the Direct button
"
corresponds to a
2. Press Direct button
"
(7 to 12) with the same
disc loaded into the magazine.
number as the CD playing.
➜➜Selecting a disc from 1 to 6
If a CD is not loaded in a slot of the magazine,
pressing Direct button
disc number is invalid.
1. Press the Shift button ! to display the
1. Press the Shift button ! to display the disc
"
corresponding to its
If “NO MAG” appears in the display, insert the
magazine into the CD changer. “LOADING”
appears in the display while the player loads
(checks) the magazine.
If “NO DISC” appears in the display, eject the
magazine and insert discs into each slot. Then,
reinsert the magazine back into the CD changer.
subdisplay.
display 1 to 6.
2. When you press the D.RPT button
"
, disc
2. Press the corresponding Direct button (1 to
repeat play starts. “D.RPT” lights in the
display.
Scan play
6)
"
to select the desired disc.
The scan play locates and plays the first 10
seconds of each track on a disc automatically.
This function continues on the disc until it is
cancelled.
➜ Selecting a disc from 7 to 12 (only when a
12 disc CD changer is used.)
3. To cancel disc repeat play, press the D.RPT
button
"
again. “D.RPT” goes off from the
1. Press the Shift button ! to display the disc
display and the unit returns to normal play
from the track being played.
display 7 to 12.
CAUTION
CD-ROM discs cannot be played in the CD
changer.
The scan play is useful when you want to select a
desired track.
2. Press the corresponding Direct button (7 to
12)
"
select the desired disc.
1. Press the Shift button ! to display the
Random play
If a CD is not loaded in a slot of the magazine,
subdisplay.
The random play selects and plays individual
tracks on the disc in no particular order. This
function continues automatically until it is
cancelled.
pressing Direct button
disc number is invalid.
"
corresponding to its
2. When you press the SCN button
starts. “SCN” lights in the display.
3. To cancel scan play, press the SCN button
"
, scan play
Pausing play
1. Press Play/pause button $ to pause play.
“PAUSE” appears in the display.
Selecting a track
➜➜Track-up
"
again. “SCN” goes off from the display and
the current track continues to play.
1. Press the Shift button ! to display the
2. To resume play, press Play/pause button $
subdisplay.
again.
1. Press the right side of SEARCH button 4 to
2. When you press the RDM button
"
, random
move ahead to the beginning of the next track.
Disc scan play
play starts. “RDM” lights in the display.
Displaying CD titles
This unit can display title data for CD-text CDs
and user titles input with this unit.
2. Each time you press the right side of SEARCH
button 4 , the track advances ahead to the
beginning of the next track.
The disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected CD changer. This function
continues automatically until it is cancelled.
3. To cancel random play, press the RDM button
"
again. “RDM” goes off from the display and
the unit returns to normal play.
➜➜Track-down
1. Press DISP button 3 to display the main
display.
1. Press the left side of SEARCH button 4 to
The disc scan play is useful when you want to
select a desired CD.
Disc random play
move back to the beginning of the current track.
2. Each time you press and hold DISP button
The disc random play selects and plays individual
tracks or discs automatically in no particular
order.This function continues automatically until
it is cancelled.
3
for 1 second or longer, the title display
2. Press the left side of SEARCH button 4 twice
1. Press the Shift button ! to display the
changes in the following order:
to move to the beginning of the previous track.
subdisplay.
User title (disc) ➜ CD-text title (disc) ➜ CD-
text title (artist) ➜ CD-text title (track) ➜ user
title (disc)...
2. When you press the D.SCN button
"
, disc
Fast-forward/fast-backward
➜➜Fast-forward
scan play starts.“D.SCN” lights in the display.
1. Press the Shift button ! to display the
3. To cancel disc scan play, press the D.SCN
subdisplay.
Note:
Press and hold the right side of SEARCH button
button
"
again. “D.SCN” goes off from the
2. When you press the D.RDM button
"
, disc
• If the CD playing is not a CD-text CD or no user
title has been input, “----------” appears in the
display.
4
for 1 second or longer.
display and normal disc play contunues on
the current track.
random play starts. “D.RDM” lights in the
display.
➜➜Fast-backward
Press and hold the left side of SEARCH button
➜➜Scrolling a CD-text title
3. To cancel disc random play, press the D.RDM
Repeat play
The repeat play continuously plays the current
track. This function continues automatically until
it is cancelled.
4
for 1 second or longer.
button
"
again. “D.RDM” goes off from the
You can scroll the display as follows.
display and the unit returns to normal play
from the track being played.
When set “A-SCROLL” to “ON”.
The title is automatically kept scrolling.
When set “A-SCROLL” to “OFF”.
Top function
The top function plays from the first track (track
No. 1) of the disc.
1. Press the Shift button ! to display the subdisplay.
18
DRX9 6 7 5 z
DRX9 6 7 5 z
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MD Changer Operations
MD Changer Operations
1. Press the Shift button ! to display the
MD changer functions
Selecting a track
➜➜Track-up
Disc scan play
subdisplay.
When an optional MD changer is connected
through the CeNET cable, this unit controls all
MD changer functions. This unit can control a
total of 2 changers (MD and/or CD).
The disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected MD changer. This function
continues automatically until it is cancelled.
2. When you press the RDM button
"
, random
1. Press the right side of SEARCH button 4 to
play starts. “RDM” lights in the display.
move ahead to the beginning of the next track.
3. To cancel random play, press the RDM button
2. Each time you press the right side of SEARCH
button 4 , the track advances ahead to the
beginning of the next track.
"
again.“RDM” goes off from the display and
The disc scan play is useful when you want to
select a desired MD.
Press FUNCTION button 7 and select the MD
changer mode to start play. If 2 MD changers
are connected, press FUNCTION button 7 to
select the MD changer for play.
the unit returns to normal play.
1. Press the Shift button ! to display the
➜➜Track-down
subdisplay.
Disc random play
1. Press the left side of SEARCH button 4 to
move back to the beginning of the current
track.
If “NO DISC” appears in the display, load MDs into
the MD changer.
2. When you press the D.SCN button
"
, disc
The disc random play selects and plays individual
tracks or discs automatically in no particular
order.This function continues automatically until
it is cancelled.
scan play starts.“D.SCN” lights in the display.
3. To cancel disc scan play, press the D.SCN
2. Press the left side of SEARCH button 4 twice
Pausing play
1. Press Play/pause button $ to pause play.
“PAUSE” appears in the display.
button
"
again. “D.SCN” goes off from the
to move to the beginning of the previous track.
display and normal disc play contunues on
the current track.
1. Press the Shift button ! to display the
subdisplay.
Fast-forward/fast-backward
➜➜Fast-forward
2. To resume play, press Play/pause button $
2. When you press the D.RDM button
"
, disc
again.
Repeat play
The repeat play continuously plays the current
track. This function continues automatically until
it is cancelled.
random play starts. “D.RDM” lights in the
display.
Press and hold the right side of SEARCH button
4
for 1 second or longer.
Switching disc titles and track titles
3. To cancel disc random play, press the D.RDM
➜➜Fast-backward
button
"
again. “D.RDM” goes off from the
This unit can display disc titles and track titles
already entered on MDs. Titles up to 128
characters long can be displayed by scrolling the
titles.
display and the unit returns to normal play
from the track being played.
1. Press the Shift button ! to display the
Press and hold the left side of SEARCH button
subdisplay.
4
for 1 second or longer.
2. When you press the RPT button
"
, repeat
Titles cannot be entered for MDs with this unit.
1. Press DISP button 3 to display the main
display.The disc title or track title is displayed.
play starts. “RPT” lights in the display.
Top function
The top function plays from the first track (track
No. 1) of the disc.
3. To cancel repeat play, press the RPT button
"
again. “RPT” goes off from the display and
the unit returns to normal play.
2. Each time you press and hold DISP button
1. Press the Shift button ! to display the disc
3
for 1 second or longer, the display toggles
display.
between the disc title and the track title.
Disc repeat play
2. Press Direct button
"
(1 to 6) with the same
After all the tracks on the current disc have been
played, the disc repeat play automatically replays
the current disc over from the first track. This
function continues automatically until it is
cancelled.
number as the MD playing.
➜Scrolling titles
You can scroll through it with the following
operation.
If an MD is not loaded in a slot of the MD changer,
pressing Direct button " corresponding to its disc
number is invalid.
When set “A-SCROLL” to “ON”.
The title is automatically kept scrolling.
When set “A-SCROLL” to “OFF”.
Scan play
1. Press the Shift button ! to display the
subdisplay.
The scan play locates and plays the first 10 sec-
onds of each track on a disc automatically. This
function continues on the disc until it is cancelled.
1. Display the MD title (disc, artist or track).
2. When you press the D.RPT button
"
, disc
2. Press and hold TITLE button # for 1 second
repeat play starts. “D.RPT” lights in the
display.
or longer. The display scrolls through the title.
The scan play is useful when you want to select a
desired track.
3. To cancel disc repeat play, press the D.RPT
Selecting an MD
Each of the Direct button
MD loaded into the MD changer.
1. Press the Shift button ! to display the
button
"
again. “D.RPT” goes off from the
subdisplay.
"
corresponds to an
display and the unit returns to normal play
from the track being played.
2. When you press the SCN button
starts. “SCN” lights in the display.
3. To cancel scan play, press the SCN button
"
, scan play
1. Press the Shift button ! to display the disc
display.
"
Random play
again.“SCN” goes off from the display and the
current track continues to play.
2. Press Direct button
desired MD.
"
(1 to 6) and select the
The random play selects and plays individual
tracks on the disc in no particular order. This
function continues automatically until it is
cancelled.
If an MD is not loaded in a slot of the MD changer,
pressing Direct button " corresponding to its disc
number is invalid.
20
DRX9 6 7 5 z
DRX9 6 7 5 z
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Operations
TV Operations
AC PROCESSOR operations
TV tuner functions
Manual tuning
Auto store
AC PROCESSOR functions
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV requires a TV tuner and
monitor.
There are 2 ways available: Quick tuning and step
tuning. When you are in the step tuning mode,
the frequency changes one step at a time. In
quick tuning mode, you can quickly tune the
desired frequency.
Auto store selects 6 TV stations automatically
and stores each one into a preset memory.
• Standard mode:
Adjustment using the graphic equalizer function
and the DSF (Digital Sound Field) function.
If there are not 6 stations with good reception,
stations previously stored in memory remain and
only the strong stations are stored into memory.
• Professional mode:
Adjustment using the VSE (VIRTUAL SPACE
ENHANCER) function and the parametric
equalizer function.
Watching a TV
1. Press FUNCTION button 7 and select the
1. Press BAND button 8 and select the desired
1. Press BAND button 8 and select the desired
band. (TV1 or TV2)
TV band. (TV1 or TV2)
If “MANU” is not lit in the display, press and
hold BAND button 8 for 1 second or longer.
“MANU” is lit in the display and manual tuning
is now available.
TV mode.
2. Press the Shift button ! to display the
When the STD mode is selected, adjustment for
the professional mode cannot be made. On the
contrary, when the professional mode is selected,
adjustment for the easy mode cannot be made.
2. Press BAND button 8 to select the desired
TV band (TV1 or TV2). Each time the button
is pressed, the input selection toggles
between TV1 and TV2.
subdisplay.
3. Press and hold the AS button
"
for 2 seconds
or longer. The stations with good reception
are automatically stored to preset buttons.
2. Tune into a station.
Operations common to each mode
Enjoying the spectrum analyzer
This unit can display the spectrum analyzer
patterns.There are 7 spectrum analyzer patterns.
➜ Quick tuning:
3. Press the right or left side of SEARCH button
Press and hold the right or left side of
SEARCH button 4 for 1 second or longer to
tune in a station.
4
to tune in the desired TV station.
Preset scan
Preset scan allows the user to view each preset
position before it automatically advances to the
next preset. This function is useful for searching
for desired TV station in memory.
Watching a video
➜ Step tuning:
The TV tuner has a VTR input terminal to which
1 external device can be connected. Connect a
12V video cassette player (VCP) or video
cassette recorder (VCR) to the TV tuner input
terminal.
1. Press DISP button 3 to select the spectrum
Press the right or left side of SEARCH button
analyzer display.
4
to manually tune in a station.
1. Press the Shift button ! to display the
2. Each time you press and hold DISP button
subdisplay.
3
for 1 second or longer, the spectrum
Recalling a preset station
2. Press the PS button
3. When the desired channel is received, press
the PS button again.
"
.
analyzer patterns are switched.
A total of 12 TV stations can be stored (6-TV1
and 6-TV2).This allows you to select your favorite
TV stations and store them in memory for later
recall.
1. Press the Shift button ! to display the
subdisplay.
"
Setting the sensitivity of the
spectrum analyzer
2. Press the VTR button
"
and select the VTR.
3. To return to the TV broadcast, press the TV
Setting the TV diver
You can change the reception setting for the TV
antenna connected to the TV tuner.
The factory default setting is “MID”.
1. Press BAND button 8 and select the desired
button
"
.
1. Press MODE button & four times to switch
to the adjustment selection display.
TV band. (TV1 or TV2)
2. Press the Shift button ! to display the preset
Tuning
2. Press VOLUME buttons 2 up (w) or down
(z) to select “ANA SENS”.
3. Press the right or left side of SEARCH button
1. Press MODE button & four times to switch
channel display.
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
to the adjustment selection display.
3. To recall a storedTV station, press the desired
2. Press VOLUME buttons 2 up (w) or down
(z) to select “TV DIVER”.
3. Press the right side of SEARCH button 4 to
Preset button
"
to select that station.
4
to move the cursor.
Press and hold one of Preset buttons
"
for 2
Seek tuning
1. Press BAND button 8 and select the desired
4. Press VOLUME buttons 2 up (w) or down
(z) to set the sensitivity of the spectrum
analyzer.
seconds or longer to store the current station
into the preset memory.
move the cursor.
TV band (TV1 or TV2).
4. Press VOLUME buttons 2 up (w) or down
(z) to set to “ON” or “OFF”.
If “MANU” is lit on the display, press and hold
BAND button 8 for 1 second or longer.
“MANU” in the display goes off and seek tuning
is now available.
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
You can choose one of “LOW”, “L-M”, “MID”
“M-H” or “HIGH” for the sensitivity of the
spectrum analyzer.
➜ ON:
Sets reception emphasizing the visual.
➜ OFF:
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
2. Press the Shift button ! to display the preset
2. Press the right or left side of SEARCH button
channel display.
4
to automatically seek a station. Press the
Sets the diver setting to OFF.
right side of SEARCH button to
4
3. Press and hold one of Preset buttons
"
for 2
5. Press MODE button & or Press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
automatically tune up the frequency band to
the next available TV station; press the left
side to automatically tune down.
seconds or longer to store the current station
to that preset memory.
22
DRX9 6 7 5 z
DRX9 6 7 5 z
23
Download from Www.Somanuals.com. All Manuals Search And Download.
AC PROCESSOR operations
AC PROCESSOR operations
Selecting the standard mode or the
professional mode
Standard mode/ G.EQ
operations
Graphic equalizer parameter (dB)
50Hz 100Hz 200Hz 400Hz 1kHz 3kHz 12kHz
Equalizer setting
1) BASS BOOST
The factory default setting is “PRO”.
+5
0
+6
0
-4
0
+2
-2
0
0
0
Note:
1. Press MODE button & four times to switch
to the adjustment selection display.
2) HIGH BOOST
3) ACOUSTICAL
4) IMPACT
+4
+6
+3
-4
0
+3
+5
+5
-4
0
+4
+1
+5
-2
0
• The adjustment made in standard mode is not
reflected in the adjustment in professional mode. On
the contrary, the adjustment made in professional
mode is not reflected in the adjustment in standard
mode.
0
+2
+4
+2
0
+1
+3
0
+4
+1
-2
2. Press VOLUME buttons 2 up (w) or down
(z) to select “AC-PROCSSR”.
3. Press the right side of SEARCH button 4 to
+4
+2
0
5) SMOOTH
6) FLAT
0
0
move the cursor.
G.EQ effect ON/OFF
4. Press VOLUME buttons 2 up (w) or down
(z) to set the mode to “STD” or “PRO”.
5. Press MODE button & or press and hold ENT
button $ for 1 second or longer to return to
the previous mode.
To select the user memory, press BAND but-
ton 8 to select “G.EQ User” and press one of
4. Press VOLUME buttons 2 up (w) or down
(z) to make the adjustment.The adjustment
range is from –12dB to +12dB.
The factory default setting is “ON”.
1. Press MODE button & two times and select
“G.EQ”.
Direct buttons
"
.
4. Press MODE button & three times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
5. Repeat steps 3 to 4 to complete the
2. Press the Shift button ! . While the “ON” is lit
in the display, the G.EQ effect is set to “ON”.
adjustment and press ENT button $ .
6. Press and hold one of Direct buttons " for 2
Entering titiles
You can give a title to the user memory of the
G.EQ, VSE and P.EQ that you have adjusted
yourself.
3. Press MODE button & three times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
seconds or longer to store the edited contents.
Editing/storing a G.EQ menu (User
memory)
1. Select a G.EQ menu which you want to edit
on the basis of.
You can give a title to the user memory. For
the inputting method of titles, refer to the
section “Entering titles” in “Operations
common to each mode”.
Note:
• If the G.EQ effect is set to OFF, the adjustment
made in “G.EQ operations” is not reflected in the
music source.
1. Press MODE button & to select the adjust-
ment mode in which you want to give a title.
7. Press MODE button & three times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
2. Press ENT button $ .
2. Press BAND button 8 to select the “User”.
3. Press the right or left side of SEARCH button
3. Press one of Direct buttons
"
to select the
4
to select the frequency to be adjusted.
Selecting a G.EQ menu
1. Press MODE button & two times and select
“G.EQ”.
user memory to which you want to give a title.
There are 50Hz, 100Hz, 200Hz, 400Hz, 1kHz,
3kHz and 12kHz available for the adjustment
frequency.
4. Press and hold TITLE button # for 1 second
or longer.
2. Press BAND button 8 to select “G.EQ Basic”.
5. Press the right or left side of SEARCH button
3. Press one of Direct buttons
desired G.EQ menu.
"
and select the
4
to move the cursor.
Standard mode/DSF operations
6. Press numbers “1” to “4” of Direct buttons
"
The basic G.EQ menus are as follows:
1) BASS BOOST:
Selecting a DSF menu
1. Press MODE button & to select “DSF”.
to select the character you want to enter.
When you press numbers “1” to “5” of Direct
DSF effect ON/OFF
The factory default setting is “ON”.
1. Press MODE button & to select “DSF”.
buttons
"
, the following title characters can
Low frequencies emphasized.
2) HIGH BOOST:
2. Press one of Direct buttons
desired a DSF menu.
"
and select the
be entered.
1 ... Capital letters
2 ... Small letters
3 ... Numbers and symbols
4 ... Umlauts
5 ... Title clear
The title clear font is used to delete a title. To
delete the title, perform the title clear operation
first and then put it into memory.
2. Press the Shift button ! . When the “ON” is lit
in the display, the DSF effect is set to “ON”.
Medium and high frequencies emphasized.
3) ACOUSTICAL:
The basic DSF menus are as follows:
3. Press MODE button & four times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
BASIC
Medium frequencies (vocals) emphasized.
4) IMPACT:
1) HALL:
Large concert hall.
2) LIVEHOUSE: Live performance hall,
larger than a jazz club.
Note:
Low and high frequencies emphasized.
5) SMOOTH:
• If the DSF effect is set to OFF, the adjustment made
in “DSF operations” is not reflected in the music
source.
3) CLUB:
4) JAZZCLUB: Jazz club with a low ceiling.
5) STUDIO: Listening room in a home.
Club with strong bass.
7. Press VOLUME buttons 2 up (w) or down
Medium and high frequencies reduced.
6) FLAT:
(z) to select the character you want to input.
8. Repeat steps 5 to 7 to input the title.
Setting the listening position
1. Press MODE button & and select “DSF”.
Flat sound.
3. Press MODE button & four times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
9. Press and hold ENT button $ for 2 seconds
or longer to put the title into memory.The title
input mode is canceled.
2. Press the right or left side of SEARCH button
4
to set the listening position type.
There are FULL SEAT, FRONT-R (only right
seat), FRONT-L (only left seat), FRONT (only
front seats), REAR (only rear seats) and PASS
available for the listening position types.
The factory default setting is “FRONT”.
24
DRX9 6 7 5 z
DRX9 6 7 5 z
25
Download from Www.Somanuals.com. All Manuals Search And Download.
AC PROCESSOR Operations
AC PROCESSOR Operations
7. Press and hold one of Direct buttons
"
for 2
8. Press MODE button & four times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
Editing/storing a DSF menu (User
memory)
1. Select a DSF menu which you want to edit on
the basis of.
Frequency
Button Sound Equalizer
seconds or longer to store the edited contents.
Characteristic
You can give a title to the user memory. For
the inputting method of titles, refer to the
section “Entering titles” in “Operations
common to each mode”.
1
FLAT
Flat sound
2. Press ENT button $ .
2
BASS BOOST Bass is boosted
3. Press the right SEARCH button 4 to select
the EFFECT to be adjusted.
3
4
5
Professional mode/P.EQ operations
HIGH BOOST High tone is boosted
Low and high tones
EFFECT: Adjusts the percentage of reflected
sound.
•
The different car types and the speaker in-
stallation positions are as follows:
P.EQ effect ON/OFF
4. Press the right side of SEARCH button 4 to
IMPACT
are boosted
The factory default setting is “ON”.
1. Press MODE button & two times to select
“P.EQ”.
move the cursor.
1) SEDAN-1 front: 2WAY
ACOUSTICAL Middle tone is boosted
Gradually attenuated
5. Press VOLUME buttons 2 up (w) or down
(z) to make the adjustment (0%~100%).
6. Press ENT button $ .
rear: Rear parcel
2) SEDAN-2 front: FULL rear: Rear door
3) WAGON-1 front: 2WAY
2. Press the Shift button ! . While the “ON” is lit
in the display, the P.EQ effect is set to “ON”.
6
SMOOTH
from low frequency
7. Press one of the Direct buttons
the edited contents.
"
to store
through high frequency
3. Press MODE button & three times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
rear: Beside the luggage
To select the user memory, press BAND button
to select “VSE User” and then press oen of
Direct buttons
4) WAGON-2 front: FULL rear: Rear door
5) MINI VAN-1 front: 2WAY
8. Press MODE button & four times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
8
"
.
Note:
rear: Beside the luggage
4. Press MODE button & four times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
• If the P.EQ effect is set to OFF, the adjustment
made in “P.EQ operations” is not reflected in the
music source.
6) MINI VAN-2 front: FULL
Professional mode/VSE operations
rear: Equivalent to rear door
To select the user memory, press BAND button
Note:
Selecting a P.EQ menu
1. Press MODE button & two times to select
“P.EQ”.
Editing/storing a VSE menu (User
memory)
1. Select a VSE menu which you want to edit on
the basis of.
8
to select “P.EQ User” and then press one
• The adjustment made in professional mode is not
reflected in the adjustment in standard mode. On
the contrary, the adjustment made in standard mode
is not reflected in the adjustment in professional
mode.
of Direct buttons
"
.
4. Press MODE button & three times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
2. Press BAND button 8 to select “P.EQ Basic”.
2. Press ENT button $ .
3. Press one of the Direct buttons
the desired P.EQ menu.
"
and select
3. Press VOLUME buttons 2 up (w) or down
(z) to select the item to be adjusted.
VSE effect ON/OFF
The factory default setting is “ON”.
1. Press MODE button & and select “VSE”.
•
The settings of the basic P.EQ menus are as follows:
Parametric Equalizer Parameter
There are DIFFUSE, CAR WIDTH and CAR
LENGTH available for the items to be
adjusted.
2. Press the Shift button ! . While the “ON” is lit
in the display, the VSE effect is set to “ON”.
Vehicle type
Channel
Front
Rear
Front
Rear
Front
Rear
Front
Rear
Front
Rear
Front
Rear
BAND 1
250Hz/F, 3/Q, -8dB/G
BAND 2
BAND 3
• The VSE adjustment contents are as follows:
DIFFUSE
Compensates for spacial impression.
CAR WIDTH
Compensates for the width of the car’s interior
(lateral direction).
CAR LENGTH
Compensates for the length of the car’s interior
(longitudinal direction).
4. Press the right side of SEARCH button 4 to
move the cursor.
2kHz/F, 1/Q, -4dB/G
5kHz/F, 1/Q, -4dB/G
8kHz/F, 5/Q, 0dB/G
8kHz/F, 1/Q, -5dB/G
3. Press MODE button & four times or press
and hold ENT button $ for 1 second or longer
to return to the previous mode.
SEDAN-1
250Hz/F, 3/Q, -10dB/G 1.25kHz/F, 5/Q, 0dB/G
250Hz/F, 7/Q, -10dB/G 800Hz/F, 3/Q, -4dB/G
SEDAN-2
Note:
80Hz/F, 7/Q, +3dB/G
250Hz/F, 3/Q, -8dB/G
250Hz/F, 3/Q, -8dB/G
125Hz/F, 5/Q, -12dB/G 1.25kHz/F, 5/Q, 0dB/G
• If the VSE effect is set to OFF, the adjustment
made in “VSE operations” is not reflected in the
music source.
1kHz/F, 3/Q, -8dB/G
800Hz/F, 1/Q, -8dB/G
10kHz/F, 1/Q, -6dB/G
8kHz/F, 5/Q, 0dB/G
WAGON-1
WAGON-2
MINI VAN-1
MINI VAN-2
250Hz/F, 7/Q, -8dB/G 400Hz/F, 7/Q, -10dB/G 1.25kHz/F, 7/Q, -8dB/G
125Hz/F, 3/Q, -8dB/G 500Hz/F, 5/Q, -5dB/G 1.6kHz/F, 3/Q, 0dB/G
125Hz/F, 5/Q, -4dB/G 1.25kHz/F, 3/Q, -4dB/G 2kHz/F, 7/Q, +3dB/G
250Hz/F, 1/Q, -6dB/G 630Hz/F, 3/Q, -4dB/G 8kHz/F, 5/Q, 0dB/G
250Hz/F, 3/Q, -4dB/G 1.25kHz/F, 3/Q, -8dB/G 80Hz/F, 3/Q, +3dB/G
250Hz/F, 3/Q, -8dB/G 500Hz/F, 5/Q, -5dB/G 8kHz/F, 5/Q, 0dB/G
F; Center frequency (Hz), Q; Q curve, G; Gain(dB)
Selecting a VSE menu
1. Press MODE button & to select “VSE”.
5. Press VOLUME buttons 2 up (w) or down
(z) to make the adjustment.The adjustment
range is to 1 to 10 for each item.
2. Press BAND button 8 to select “VSE Basic”.
3. Press one of Direct buttons
desired VSE menu.
"
and select the
6. Repeat steps 3 to 5 to complete the
adjustment and press ENT button $ .
26
DRX9 6 7 5 z
DRX9 6 7 5 z
27
Download from Www.Somanuals.com. All Manuals Search And Download.
AC PROCESSOR Operations
9. TROUBLESHOOTING
About the Q-curve (Q)
Editing/storing a P.EQ menu (User
memory)
1. Select a P.EQ menu which you want to edit
on the basis of.
For the Q-curve (Q), setting larger values makes
the curve sharper, setting smaller values makes
the curve flatter. (Figure 2)
Problem
Cause
Measure
Power does not
turn on.
Fuse is blown.
Replace with a fuse of the same amperage. If the
fuse blows again, consult your store of purchase.
Selecting the Q-curve (Q) opposite to the fre-
quency curve to be compensated makes the fre-
quency characteristics flat.
2. Press ENT button
$
.
(No sound is
produced.)
Incorrect wiring.
Consult your store of purchase.
3. Press VOLUME buttons 2 up (w) or down
(z) to select the item to be adjusted.
Nothing happens The microprocessor has
when buttons are malfunctioned due to noise,
Press the reset button for about 2 seconds with a thin
rod.
Q curve (Q)
There are selections of correction channel,
correction band, the center frequency, the Q-
curve and gain adjustment available for the
items to be adjusted.
pressed.
etc.
Display is not
accurate.
Reset button
High
Low
• The P.EQ adjustment contents are as follows:
Channel selection
Select the channel to be compensated (front
or rear).
Selection of center frequency
Select the center frequency that you want to
compensate from the range of 20Hz to 20kHz.
(1/3 octave step, 31 points)
Q curve; 20
Q curve; 1
Figure 2
DCP or source unit
connectors are dirty.
Wipe the dirt off with a soft cloth moistened with
cleaning alcohol.
4. Press the right side of SEARCH button 4 to
move the cursor.
Selection of Q-curve
Set the sharpness of the Q-curve to one of the
parameters: 1, 3, 5, 7 and 20.
Gain adjustment
Adjust the gain (output level) in the range of -
12dB to +12dB. (1dB step, 25 points)
5. Press VOLUME buttons 2 up (w) or down
(z) to make the adjustment.
6. Repeat steps 3 to 5 to complete the
Compact disc
cannot be loaded. already loaded.
Another compact disc is
Eject the compact disc before loading the new one.
There is a disc other than a
CD or foreign matter already longer. The foreign matter is forcibly ejected.
in place.
Press and hold OPEN button 6 for 2 seconds or
adjustment and press ENT button $ .
7. Press and hold one of Direct buttons
"
for 2
seconds or longer to store the edited contents.
About the compensation of frequency char-
acteristics
Sound skips or is Compact disc is dirty.
Clean the compact disc with a soft cloth.
You can give a title to the user memory. For
the inputting method of titles, refer to the
section “Entering titles” in “Operations
common to each mode”.
noisy.
Compact disc is heavily
scratched or warped.
Replace with a compact disc with no scratches.
See Figure 1 concerning the relationship of the
center frequency, Q-curve (Q) and gain.
Sound is bad
directly after
power is turned
on.
Water droplets may form on
the internal lens when the
car is parked in a humid
place.
Let dry for about 1 hour with the power on.
8. Press MODE button
and hold ENT button
&
$
three times or press
for 1 second or longer
Level
(dB)
Q curve (Q)
Q=
F
f
to return to the previous mode.
3dB
Poor sound
quality
The equalizer levels are too
high.
If the equalizer levels are too high, the sound may
distort. Lower the equalizer levels.
Gain
(G)
f
Frequency curve
Center frequency (F)
Frequency (Hz)
Figure 1
28
DRX9 6 7 5 z
DRX9 6 7 5 z
29
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ERROR DISPLAYS
11. SPECIFICATIONS
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
FM Tuner
Audio
Frequency Range:
87.9 MHz to 107.9 MHz
Usable Sensitivity:
11 dBf
Line Output Level (CD 1 kHz):
4 V
Cause
Error Display
ERROR 2
Measure
A CD is caught inside the CD deck and is
not ejected.
This is a failure of CD deck’s mechanism
and consult your store of purchase.
General
Power Supply Voltage:
50dB Quieting Sensitivity:
17 dBf
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR H
A CD cannot be played due to scratches,
etc.
Replace with a non-scratched,
non-warped disc.
14.4 V DC (10.8 to 15.6 V allowable),
negative ground
Alternate Channel Selectivity:
75 dB
Current Consumption:
Less than 7 A
A CD is loaded upside-down inside the CD Eject the disc then reload it properly.
deck and does not play.
Stereo Separation (1 kHz):
35 dB
Weight / Source unit:
4 lb. (1.8 kg)
A CD inside the CD changer is not loaded. This is a failure of CD changer’s mechanism
and consult your store of purchase.
Frequency Response (±3 dB):
30 Hz to 15 kHz
Weight / Remote control unit:
1 oz. (30 g) (including battery)
Dimensions / Source unit:
A CD inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-warped
disc.
AM Tuner
A CD inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
7" (Width) × 2" (Height) × 6-2/25" (Depth)
[178 (W) × 50 (H) × 152 (D) mm]
Frequency Range:
530 kHz to 1710 kHz
Usable Sensitivity:
25 µV
Displayed when the temperature in the
MD changer is too high and playback has for a while to cool off MD changer.
been stopped automatically.
Lower the surrounding temperature and wait
Dimensions / Remote control unit:
1-3/4" (Width) × 4-5/16" (Height) × 1-1/8"
(Depth)
ERROR 2
ERROR 3
ERROR 6
An MD inside the MD changer is not loaded. This is a failure of MD changer’s mechanism
[44 (W) × 110 (H) × 27 (D) mm]
and consult your store of purchase.
CD Player
System:
An MD inside the MD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-warped
disc.
Compact disc digital audio system
Usable Discs:
An MD inside the MD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Compact disc
Frequency Response (±1 dB):
5 Hz to 20 kHz
Displayed when a non-recorded MD is
loaded in the MD changer.
Load a pre-recorded MD in the MD changer.
Signal to Noise Ratio (1 kHz):
110 dB
If an error display other than the ones described above appears, press the reset button. If the problem
persists, turn off the power and consult your store of purchase.
Dynamic Range (1 kHz):
100 dB
Harmonic Distortion:
0.005%
Notes:
• Specifications comply with EIA Standards.
• Specifications and design are subject to change without notice for further improvement.
30
DRX9 6 7 5 z
DRX9 6 7 5 z
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
32
DRX9 6 7 5 z
Download from Www.Somanuals.com. All Manuals Search And Download.
|