Owner’s manual
Mode d’emploi
Manual de instrucciones
DRX8675z
AM/FM CD PLAYER
WITH CD/MD CHANGER CONTROL
•
COMBINÉ RADIO/CD AM/FM AVEC PILOTE
DE CHANGEUR CD/MD
•
RADIO DE AM/FM Y REPRODUCTOR DE DISCOS
COMPACTOS CON CONTROL DE CAMBIADOR
DE DISCOS COMPACTOS/MINIDISCOS
OPEN
DRX8675z
ISR
1
2
3
4
5
6
Clarion Co., Ltd.
PE-2332B
280-7401-00
All Rights Reserved. Copyright © 1999: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Inpreso en China
1999/8 (CL·C)
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling Compact Discs
6. REMOTE CONTROL
2. PRECAUTIONS
Use only compact discs bearing the
mark.
Receiver for remote control unit
1. When the inside of the car is very cold and
the player is used soon after switching on
the heater moisture may form on the disc or
the optical parts of the player and proper
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft cloth.
If moisture forms on the optical parts of the
player, do not use the player for about one
hour. The condensation will disappear natu-
rally allowing normal operation.
3. When the auto antenna cord is connected to
the car auto antenna cord, when the unit is
switched to the radio mode (or theTV mode),
the antenna is extended automatically. If the
car is in a narrow space, the antenna may
strike something, so be careful.
Do not play heart-shaped, octagonal, or other specially shaped compact discs.
OPEN
• To remove a compact disc from its storage
Handling
DRX8675z
case, press down on the center of the case
and lift the disc out, holding it carefully by the
edges.
• Do not use commercially available CD protec-
tion sheets or discs equipped with stabilizers,
etc. These may damage the disc or cause
breakdown of the internal mechanism.
• New discs may have some roughness around
the edges. If such discs are used, the player
may not work or the sound may skip. Use a
ball-point pen or the like to remove any rough-
ness from the edge of the disc.
ISR
1
2
3
4
5
6
4. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
Operating range: 30° in all directions
Ball-point pen
Roughness
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
Storage
Remote control unit
Signal transmitter
• Do not expose compact discs to direct sun-
light or any heat source.
• Do not expose compact discs to excess hu-
midity or dust.
• Do not expose compact discs to direct heat
from heaters.
This equipment has been tested and found to
comply with the limits for a Class B digital de-
vice, pursuant to Part 15 of the FCC Rules.
CAUTION
USE OF CONTROLS, ADJUSTMENTS, OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN, MAY RE-
SULT IN HAZARDOUS RADIATION EXPO-
SURE.
These limits are designed to provide reason-
able protection against harmful interference in
a residential installation.
• Never stick labels on the surface of the com-
pact disc or mark the surface with a pencil or
pen.
• Never play a compact disc with any cellophane
tape or other glue on it or with peeling off marks.
If you try to play such a compact disc, you may
not be able to get it back out of the CD player
or it may damage the CD player.
• Do not use compact discs that have large
scratches, are misshapen, cracked, etc. Use
of such discs may cause misoperation or dam-
age.
Cleaning
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the cen-
ter of the compact disc to the circumference.
• Do not use any solvents, such as commercially
available cleaners, anti-static spray or thinner
to clean compact discs.
This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio com-
munications. However, there is no guarantee
that interference will not occur in a particular
installation.
THE COMPACT DISC PLAYER and MINI DISC
PLAYER SHOULD NOT BE ADJUSTED OR
REPAIRED BY ANYONE EXCEPT PROPERLY
QUALIFIED SERVICE PERSONNEL.
CHANGES OR MODIFICATIONS NOT EX-
PRESSLY APPROVED BY THE MANUFAC-
TURER FOR COMPLIANCE COULD VOID
THE USER’S AUTHORITYTO OPERATETHE
EQUIPMENT.
• After using special compact disc cleaner, let
the compact disc dry off well before playing it.
If this equipment does cause harmful interfer-
ence to radio or television reception, which can
be determined by turning the equipment off and
on, the user is encouraged to consult the dealer
or an experienced radio/TV technician for help.
INFORMATION FOR USERS:.
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE MANU-
FACTURER WILL VOID THE WARRANTY
AND WILL VIOLATE FCC APPROVAL.
Flip Down Panel
Inserting the Batteries
MODEL
This unit uses a flip-down structure that makes possible large-size displays.
12V
GROUND
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
3. Do not use the FLIP DOWN PANEL as a tray
AM 530-1710kHz/FM 87.9-107.9MHz
CAUTION
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE TAHT MAY CAUSE UNDESIRED
OPERATION.
to place objects on when it is open.
AA (UM-3/1.5V)
Batteries
When opening and closing the FLIP DOWN
PANEL, be careful not to catch your fingers.
They could be injured.
2. Insert the AA (UM-3/1.5V) batteries that came
with the remote control unit facing in the
directions shown in the figure, then close the
rear cover.
4. When closing the FLIP DOWN PANEL, do not
press OPEN button 1 .
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR
SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE.
5. Strong impacts to the operating or display
section can cause damage or deformation.
CLARION CO.,LTD.
50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN
1. Always use this unit with the FLIP DOWN
PANEL closed.
6. If the FLIP DOWN PANEL does not open fully,
gently open it with your hand.
Notes:
051 722 877
Rear cover
Using batteries improperly can cause them to ex-
plode. Take note of the following points:
• When replacing batteries, replace both batteries
with new ones.
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or water.
• Dispose of spent batteries properly.
MANUFACTURED:
2. Do not force operations or use this device ab-
normally when opening or closing the FLIP
DOWN PANEL.
Rear side
286-
Clarion Co.,Ltd.
MADE IN
SERIAL No.
PE-
Bottom View of Source Unit
Be sure to unfold and read the next page.
Veuillez déplier et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
8
DRX8 6 7 5 z
DRX8 6 7 5 z
3
DRX8 6 7 5 z
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. CONTROLS / LES COMMANDES / CONTROLES
4. NOMENCLATURE
5. DCP
Note:
The control panel can be detached to prevent theft. When detaching the control panel, store it in the
DCP (DETACHABLE CONTROL PANEL) case to prevent scratches.
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).
Source unit / Appareil pilote / Unidad fuente
We recommend taking the DCP with you when leaving the car.
Names of Buttons
Removing the DCP
1. Hold down POWER button 3 for 1 second
Attaching the DCP
1. Insert the right side of the DCP into the source
unit.
1
OPEN button
9
Preset buttons (1 to 6)
Direct buttons (1 to 6) (7 to 12)
DISP (display) button
ISR (instant station recall) button
BND (band) button
TOP button
2
ENT (enter) button
OPEN
or longer to turn off the power.
DRX8675z
Play/pause button
!
2. Insert the left side of the DCP into the source
unit.
3
4
5
POWER button
"
#
2.
FNC (function) button
TITLE button
ISR
1
2
3
4
5
6
ADJ (adjust) button
PS/AS (preset scan/auto store) button
SCN (scan) button
$
A-M (audio mode) button
LOUD (loudness) button
SEARCH button
%
&
(
2. Deeply push in OPEN button 1 to unlock
1.
6
7
8
RPT (repeat) button
RDM (random) button
Z-EHCR (z-enhancer) button
Rotary knob
the FLIP DOWN PANEL.
With the FLIP DOWN PANEL opened / Ouverture du PANNEAU RABATTABLE /
Apertura del PANEL ABATIBLE
If the FLIP DOWN PANEL does not open fully,
gently open it with your hand.
CD insertion slot
)
Eject button
CAUTION
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it
or subject it to strong shocks.
Display Items
• If the FLIP DOWN PANEL is kept open, the
DCP may drop due to vibration of the car.
1
2
3
4
5
6
7
8
9
Single disc indication
Disc in indication
$
A-M (audio mode) indication
LD (loudness) indication
Graphic indication
3. Pull the DCP toward you and remove it.
%
&
This results in damage to the DCP. So close
the FLIP DOWN PANEL or remove the DCP
to store into the case.
EASY mode indication
G.EQ indication
DCP
Levels are displayed in adjusting the volume,
etc.
• The connector connecting the source unit
and the DCP is an extremely important part.
Be careful not to damage it by pressing on
it with fingernails, screwdrivers, etc.
DSP indication
(
)
Long title indication
PRO (professional) mode indication
P.EQ indication
When the texts for CD or MD are more than
11 characters, this indication lights.
Display / Afficheur / Visualizador
Note:
S.EQ indication
Operation status indication
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
Preset channel indication (1 to 6)
Disc number indication (1 to 12)
The frequency, play time, clock, etc. are
displayed.
4. Close the HOLD FLAP.
~
+
,
RDM (random) indication
RPT (repeat) indication
SCN (scan) indication
DISC indication
The disc numbers corresponding to the discs
in the CD or MD changer light.
!
ST (stereo) indication
"
#
MANU (manual) indication
Function mode indication
-
.
Z-EHCR (z-enhancer) indication
HOLD FLAP
The names of modes being selected, etc. are
displayed.
CAUTION
Be sure to close the HOLD FLAP for safety
when removing the DCP.
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
5
DRX8 6 7 5 z
6
DRX8 6 7 5 z
DRX8 6 7 5 z
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Functions of Remote Control Unit Buttons
CD changer
MD changer
Mode
Radio
CD
TV
Button
,
FUNC
Turns power on and off. When pressed and held for 1 second: Turns power off.
Switches among radio, CD, CD changer, MD changer and TV.
-
BAND
DISC UP
Plays the first track. Moves the next disc
Top play. in increasing order.
Switches reception
band.
Switches reception
band.
PROG
TOP
Increases and decreases volume (in all modes).
.
VOLUME
SEARCH
/
Moves preset
channels up and
down.
Moves tracks up
and down.
Moves tracks up
and down.
Moves preset
channels up and
When pressed and When pressed and down.
held for 1 second:
Fast-forward/
fast-backward.
held for 1 second:
Fast-forward/
fast-backward.
:
PLAY/PAUSE
No function.
Switches between
Switches between
No function.
playback and pause. playback and pause.
Turns mute on and off.
;
MUTE
ISR
Recalls ISR radio station in memory.
<
Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio
mode only).
Switches among main display, sub display, clock display and spectrum analyzer display
(only when connected to DPH7500z).
=
>
DISP
Preset scan.
Scan play.
Scan play.
Preset scan.
SCN
When pressed and
held for 2 seconds:
Auto store.
When pressed and When pressed and
held for 1 seconds: held for 2 seconds:
PS/AS
Disc scan play.
Auto store.
No function.
Repeat play.
Random play.
Repeat play.
No function.
?
RPT
BLS
When pressed and
held for 1 seconds:
Disc repeat play.
No function.
Random play.
When pressed and TV and VTR.
held for 1 seconds:
Switches between
@ RDM
DOLBY NR
MONI
Disc random play.
* Some of the corresponding buttons on the source unit and remote control unit have different functions.
9
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
7. OPERATIONS
Note: Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
Basic Operations
Radio mode ➜ CD mode ➜ CD changer mode
➜ MD changer mode ➜ TV mode ➜ Radio
CAUTION
mode...
Be sure to lower the volume before switching
off the unit power or the ignition key.The unit
remembers its last volume setting. If you
switch the power off with the volume up, when
you switch the power back on, the sudden
loud volume may hurt your hearing and dam-
age the unit.
External equipment not connected with CeNET
is not displayed.
Adjusting the volume
Turning the Rotary knob & clockwise increases
the volume; turning it counterclockwise de-
creases the volume.
The clock is displayed when the ignition key
is turned to the ACC (accessory) or IGN (igni-
tion-on) position even when the unit power
is off. In some cars, the clock may momen-
tarily disappear when the ignition key is
turned to the START position. The clock will
reappear after the engine has started and the
ignition key is released to the IGN (ignition-
on) position.
The volume level is from 0 (minimum) to 33 (maxi-
mum).
Switching the display
Press DISP button ! to select the desired display.
Each time you press DISP button ! , the display
switches in the following order:
Main display
Turning on/off the power
Note:
• Be careful about using this unit for a long time with-
out running the engine. If you drain the car’s bat-
tery too far, you may not be able to start the en-
gine and this can reduce the service life of the
battery.
1. Press POWER button 3 .
Sub (title) display
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold POWER button 3 for 1 sec-
ond or longer to turn off the power for the unit.
Note:
Clock display
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “SYSTEM CHCK” appears in the
display, so press POWER button 3 . The system
check starts within the unit.When the system check
is complete, the power is turned off, so press
POWER button 3 again.
Spectrum analyzer display
Selecting a mode
1. Press FNC button 3 to change the mode of
operation.
2. Each time you press FNC button 3 , the mode
of operation changes in the following order:
Main display...
10
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
The spectrum analyzer display is only displayed
when the DPH7500z is connected.
decreases the output volume.
* The factory default setting is “4”.
(Setting range: 0 to 7)
Once selected, the preferred display becomes
the display default.When a function adjustment
such as volume is made, the screen will
momentarily switch to that function’s display,
then revert back to the preferred display sev-
eral seconds after the adjustment.
3. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
When you have entered a title in a CD, it
appears in the sub display. If you have not
entered a title, “NO-TTL” appears in the title
display instead. For information on how to enter
a title, refer to the subsection “Entering titles”
in the “Other Handy Functions”.
Setting tone bypass
The tone bypass disables the tone (bass and
treble) functions and cuts the noise generated
when the tone functions are on.
1. Press A-M button $ and select “TONE BYPASS”.
2. Turning the Rotary knob & clockwise sets the
tone bypass to “YES” (ON); turning it
counterclockwise sets the tone bypass to
“NO” (OFF).
Setting the Z-enhancer
This unit comes with 3 types of sound tone effects
stored in memory. Select the one you prefer.
The factory default setting is “Z-EHCR OFF”.
Each time you press Z-EHCR button 8 , the tone
effect changes in the following order:
The factory default setting is “NO” (OFF).
If the setting is “YES” (ON), the bass and treble
adjustments cannot be made.
3. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜ “Z-
ENHANCER 3” ➜ “Z-EHCR OFF” ➜ “Z-
ENHANCER 1”...
Note:
• Z-ENHANCER 1 : bass emphasized
• Z-ENHANCER 2 : treble emphasized
• Z-ENHANCER 3: bass and treble emphasized
• If you set the Z-ENHANCER function to ON (1 to
3), you cannot set the tone bypass.
• Z-EHCR OFF
: no sound effect
Adjusting the bass
1. Press A-M button $ and select “BASS”.
Adjusting the tone
Press A-M button $ and select the item to adjust.
Each time you press A-M button $ , the item
changes in the following order:
2. Turning the Rotary knob & clockwise empha-
sizes the bass; turning it counterclockwise
attenuates the bass.
The factory default setting is “0”.
(Adjustment range: – 6 to +6)
➜➜When the Z-enhancer and tone bypass are off
“NON-FAD VOL” ➜ “TONE BYPASS” ➜
“BASS” ➜ “TREBLE” ➜ “BALANCE” ➜
“FADER” ➜ Function mode...
The bass cannot be adjusted if the tone by-
pass setting is “YES” (ON).
3. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
➜➜When Z-enhancer 1, 2 or 3 is set
“NON-FADVOL” ➜ “Z-EHCR” ➜ “BALANCE”
➜ “FADER” ➜ Function mode...
Note:
• When the separately-sold digital sound processor
(DPH7500z) is used, the tone bypass, bass and
treble tone adjustments cannot be selected. To
adjust the tone, refer to the chapter “DSP
Operations”.
Adjusting the treble
1. Press A-M button $ and select “TREBLE”.
2. Turning the Rotary knob & clockwise empha-
sizes the treble; turning it counterclockwise
attenuates the treble.
The factory default setting is “0”.
(Adjustment range: – 6 to +6)
The treble cannot be adjusted if the tone by-
pass setting is “YES” (ON).
Adjusting the non-fader output volume
You can adjust the volume output from the unit’s
non-fader output terminal.
3. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
1. Press A-M button $ and select“NON-FADVOL”.
2. Turning the Rotary knob & clockwise increases
the output volume; turning it counterclockwise
11
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
Basic Operations
Adjusting the balance
Turning on/off the loudness
1. Press A-M button $ and select “BALANCE”.
The loudness effect emphasizes the bass and
treble to create a natural sound tone. When you
are listening to music at a low volume, it is rec-
ommended to use the loudness effect.
2. Turning the Rotary knob & clockwise empha-
sizes the sound from the right speaker; turn-
ing it counterclockwise emphasizes the sound
from the left speaker.
1. Press and hold LOUD button $ for 1 second
or longer to turn on the loudness effect.When
the loudness effect is turned on, “LD” lights in
the display.
The factory default setting is “0”. (Adjustment
range: L13 to R13)
3. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
2. Press and hold LOUD button $ for 1 second
or longer to turn off the loudness effect. “LD”
goes off in the display.
Adjusting the fader
1. Press A-M button $ and select “FADER”.
Note:
• When using a sold separately digital sound pro-
cessor (DPH7500z), a feature called auto loud-
ness is selected.This function is different from the
loudness effect. For further details on the auto loud-
ness feature, refer to the subsection “Output
adjustment of auto loudness, subwoofer and
playback band”.
2. Turning the Rotary knob & clockwise empha-
sizes the sound from the front speakers; turn-
ing it counterclockwise emphasizes the sound
from the rear speakers.
The factory default setting is “0”. (Adjustment
range: F12 to R12)
3. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
Adjusting the Z-enhancer
1. Press Z-EHCR button 8 and select the Z-
enhancer mode (1 to 3) to adjust.
2. Press A-M button $ and select “Z-EHCR”.
3. Turning the Rotary knob & clockwise adjusts
in the + direction; turning it counterclockwise
adjusts in the – direction.
When Z-enhancer 1 is selected, you can adjust
the bass in the range of ±2.
When Z-enhancer 2 is selected, you can adjust
the treble in the range of ±2.
When Z-enhancer 3 is selected, you can adjust
the bass and treble in the range of ±2.
4. When the adjustment is complete, press A-M
button $ several times until the function mode
is reached.
Note:
• If you set the Z-ENHANCER function to ON (1 to
3), you cannot set the tone bypass.
12
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
Radio Operations
2. Press the right or left side of SEARCH button
% to automatically seek a station.
FM reception
®
For enhanced FM performance the
When the right side of SEARCH button % is
pressed, the station is sought in the direction
of higher frequencies; if the left side of
SEARCH button % is pressed, the station is
sought in the direction of lower frequencies.
tuner includes signal actuated stereo control,
Enhanced Multi AGC, Impulse noise reduction
circuits and Multipath noise reduction circuits.
Changing the reception area
This unit is initially set to USA frequency intervals
of 10kHz for AM and 200kHz for FM.When using it
outside the USA, the frequency reception range
can be switched to the intervals below.
Manual tuning
There are 2 ways available:Quick tuning and step
tuning.
When you are in the step tuning mode, the
frequency changes one step at a time. In quick
tuning mode, you can quickly tune the desired
frequency.
1. Press BND button # and select the desired
band (FM or AM).
➜➜Setting the reception area
1. Press BND button # and select the desired
radio band (FM or AM).
2. While pressing RDM button 7 , each time you
press and hold the number “1” of the Preset
buttons 9 for 2 seconds or longer, the
reception area switches from inside the USA
to outside the USA or from outside the USA to
inside the USA.
If “MANU” is not lit in the display, press and
hold BND button # for 1 second or longer.
“MANU” is lights in the display and manual
tuning is now available.
2. Tune into a station.
Any station preset memories are lost when the
reception area is changed.
➜ Quick tuning:
Press and hold the right or left side of
SEARCH button % for 1 second or longer to
tune in a station.
Listening to the radio
1. Press FNC button 3 and select the radio
➜ Step tuning:
mode.
Press the right or left side of SEARCH button
% to manually tune in a station.
2. Press BND button # and select the radio
band. Each time the button is pressed, the
radio reception band changes in the following
order:
Recalling a preset station
FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1...
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exists to store individual radio
stations in memory. Pressing the corresponding
preset button recalls the stored radio frequency
automatically.
3. Press the right or left side of SEARCH button
% to tune in the desired station.
Tuning
1. Press BND button # and select the desired
There are 3 types of tuning mode available, seek
tuning, manual tuning and preset tuning.
band (FM or AM).
2. Press the corresponding Preset button 9 to
recall the stored station.
Seek tuning
1. Press BND button # and select the desired
Press and hold one of the Preset buttons 9
for 2 seconds or longer to store that station into
preset memory.
band (FM or AM).
If “MANU” is lit in the display, press and hold
BND button # for 1 second or longer.“MANU”
in the display goes off and seek tuning is now
available.
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
2. Press and hold one of the Preset buttons 9
for 2 seconds or longer to store the current
station into preset memory.
13
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
Radio Operations
Auto store
Auto store is a function for storing up to 6 stations
that are automatically tuned in sequentially. If 6
stations cannot be received, a previously stored
station remains unoverwritten at the memory
position.
CD Operations
Loading a CD
1. Press OPEN button 1 to access the CD
insertion slot behind the FLIP DOWN PANEL.
2. Insert a CD into the center of the insertion
slot with the label side facing up.The CD plays
automatically after loading.
1. Press BND button # and select the desired
Notes:
band (FM or AM).
• Never insert foreign objects into the CD
insertion slot.
2. Press and hold AS button 5 for 2 seconds or
longer. The stations with good reception are
stored automatically to the Preset buttons 9 .
• If the CD is not inserted easily, there may be
another CD in the mechanism or the unit may
require service.
• Discs not bearing the
ROMs cannot be played by this unit.
mark and CD-
Preset scan
Preset scan receives the stations stored in preset
memory in order. This function is useful when
searching for a desired station in memory.
Loading 3" (8 cm) compact discs
* No adapter is required to play a 3" CD.
* Insert the 3" CD into the center of the insertion
slot.
* When a 3" CD is loaded, “SINGLE” lights in
the display.
1. Press PS button 5 .
2. When a desired station is tuned in, press PS
button 5 again to continue receiving that
station.
3. Close the FLIP DOWN PANEL.
Note:
• Be careful not to press and hold PS button 5 for
2 seconds or longer, otherwise the auto store
function engages and the unit starts storing
stations.
.
CAUTION
Be careful not to catch your hand or fingers
while closing the FLIP DOWN PANEL.
Notes:
Instant station recall (ISR)
• If the FLIP DOWN PANEL does not open fully,
gently open with your hand.
• After loading a CD, always close the FLIP DOWN
PANEL.
Instant station recall is a special radio preset that
instantly accesses a favorite radio station at a
touch of a button.The ISR function even operates
with the unit in other modes.
Listening to a CD already inserted
➜ ISR memory
Press FNC button 3 to select the CD mode. Play
starts automatically.If no CD is loaded in the unit,
“NO DISC” appears in the display.
1. Select the station that you wish to store in ISR
memory.
2. Press and hold ISR button " for 2 seconds
or longer.
Pausing play
1. Press Play/pause button 2 to pause play.
“PAUSE” appears in the display.
➜ Recalling a station with ISR
In any mode, press ISR button " to turn on the
radio function and tune the selected radio station.
“ISR” appears in the display. Press ISR button
2. To resume CD play, press Play/pause button
2
again.
"
again to return to the previous mode.
Displaying CD titles
This unit can display title data for CD-text CDs
and user titles input with this unit.
1. Press DISP button ! to display the title.
2. Each time you press and hold DISP button
!
for 1 second or longer, the title display
changes in the following order:
User title (disc) ➜ CD-text title (disc) ➜ CD-
text title (track) ➜ user title (disc)...
14
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
CD Operations
Note:
➜➜Track-down
• If the CD playing is not a CD-text CD or no user
title has been input, “NO-TTL” appears in the
display.
1. Press the left side of SEARCH button % to
move back to the beginning of the current track.
2. Press the left side of SEARCH button % twice
➜➜Scrolling a CD-text title
to move to the beginning of the previous track.
When a CD-text title is longer than 11 characters,
you can scroll the display as follows.
Fast-forward/fast-backward
➜➜Fast-forward
1. Display the CD-text title (disc or track).
2. Press TITLE button 4 . The title scrolls.
Press and hold the right side of SEARCH button
% for 1 second or longer.
Ejecting a CD
1. Press OPEN button 1 to open the FLIP
➜➜Fast-backward
Press and hold the left side of SEARCH button
% for 1 second or longer.
DOWN PANEL.
2. Press Eject button ) to eject the CD. Take it
out from the ejected position.
Top function
The top function resets the CD player to the first
track of the disc. Press TOP button # to play the
first track (track No. 1) on the disc.
“DISC CHECK” appears in the display when
the CD is left in the ejected position.
3. Close the FLIP DOWN PANEL.
CAUTION
Scan play
The scan play locates and plays the first 10
seconds of each track on a disc automatically.This
function continues on the disc until it is canceled.
Be careful not to catch your hands or fingers
while closing the FLIP DOWN PANEL.
Notes:
The scan play is useful when you want to select a
desired track.
• If the FLIP DOWN PANEL does not open fully,
gently open with your hand.
• After taking out the CD, be sure to close the FLIP
DOWN PANEL.
1. Press SCN button 5 to start track scanning.
“SCN” lights in the display.
If a CD (12 cm) is left in the ejected position for 15
seconds, the CD is automatically reloaded (Auto
reload).
3" CDs (8 cm) are not auto reloaded. Be sure to
remove it when ejected.
2. To cancel the scan play, press SCN button 5
again. “SCN” goes off from the display and
the current track continues to play.
Repeat play
Notes:
The repeat play continuously plays the current
track. This function continues automatically until
it is canceled.
• If you force a CD into before auto reloading,
this can damage the CD.
• The radio mode is selected automatically 4 seconds
after Eject button ) is pressed. If the auto antenna
terminal for this unit is connected, the antenna is
extended automatically. If you are in a location
where the antenna may strike something, press
FNC button 3 to switch the mode.
1. Press RPT button 6 . “RPT” lights in the
display and the current track is repeated.
2. To cancel the repeat play, press RPT button
6
again. “RPT” goes off from the display and
• “DISC CHECK” in the display shows you a CD is
left in the unit. Be sure to press Eject button )
and remove it in this case.
normal play resumes.
Random play
The random play selects and plays individual tracks
on a disc in no particular order. This function
continues automatically until it is canceled.
Selecting a track
➜➜Track-up
1. Press the right side of SEARCH button % to
1. Press RDM button 7 . “RDM” lights in the
display, an individual track is selected
randomly and play begins.
move ahead to the beginning of the next track.
2. Each time you press the right side of SEARCH
button % , the track advances ahead to the
beginning of the next track.
2. To cancel the random play, press RDM button
7
again.“RDM” goes off from the display and
normal play resumes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
Other Handy Functions
Setting the clock
1. Press and hold ADJ button 4 for 1 second or
Mode
Number of titles
30 titles
Radio mode
CD mode
TV mode
longer to switch to the adjustment selection display.
50 titles
2. Press the right or left side of SEARCH button
15 titles
% to select “CLOCK”.
CD changer mode
CDC655z connected
CDC655Tz connected
CDC1255z connected
Number of titles
60 titles
3. Press ENT button 2 .
4. Press the right or left side of SEARCH button
100 titles
% to select the hour or the minute.
50 titles
5. Turn the Rotary knob & clockwise or
counterclockwise to set the correct time.
1. Press FNC button 3 to select the mode you want
The clock is displayed in 12-hour format.
to enter a title. (radio, CD, CD changer or TV)
6. Press ENT button 2 to store the time into memory.
Titles cannot be entered for MDs with this unit.
2. Select and play a CD or a CD in the CD changer
or tune to an appropriate TV or radio station.
7. Press ADJ button 4 to return to the previous mode.
Note:
•
You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the car’s
battery or take out this unit, the clock is reset.While
setting the clock, if another button or operation is
selected, the clock set mode is canceled.
3. Press DISP button ! and display the subtitle.
4. Press TITLE button 4 . “TITL” appears in the
display and the cursor position flashes.
5. Press the right or left side of SEARCH button
% to move the cursor.
Dimmer level setting
You can reduce the display illumination linked to
the car illumination.
6. Press DISP button ! to select a character.
Each time you press DISP button ! , the
character changes in the following order:
The factory default setting is “LEVEL 3”.
Capital letters ➜ Small letters ➜ Numbers ➜
Symbols ➜ Umlaut ➜ Capital letters...
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection display.
7. Turn the Rotary knob & to select the desired
character. Turning the Rotary knob &
clockwise moves the cursor to the next
character; turning it counterclockwise moves
the cursor to the previous character.
2. Press the right or left side of SEARCH button
% to select “DIMMER LV”.
3. Press ENT button 2 .
4. Turn the Rotary knob & clockwise or
counterclockwise to set the dimmer level.
Choose the dimmer level from the following.
8. Repeat steps 5 to 7 to enter up to 10
characters for the title.
9. Press and hold ENT button 2 for 2 seconds
or longer to store the title into memory and
cancel title input mode.
“OFF”,➜ “LEVEL 1”,➜ “LEVEL 2”, “LEVEL 3”,
“LEVEL 4”, “LEVEL 5”.
LEVEL 1 to LEVEL 5:
The greater the dimmer level is, the more the
illumination is reduced.
Clearing titles
1. Play a CD or a CD in a CD changer or tune a
radio station or TV station that you want to
clear the title for.
OFF:
Even if the car illumination is turned on,
reduction of the display illumination does not
occur.
2. Press DISP button ! and display the subtitle.
3. Press TITLE button 4 . “TITL” appears in the
display and the display switches to the title
input display.
5. Pressing ENT button 2 returns to the
adjustment selection display.
6. Press ADJ button 4 to return to the previous
4. Press BND button # .
mode.
5. Press and hold ENT button 2 for 2 seconds
or longer to clear the title and cancel the title
input mode.
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for radio stations and
CDs. The numbers of titles that can be entered
for each mode are as follows.
16
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
Other Handy Functions
Message display
Adjusting the display contrast
You can adjust the display contrast according to
the angle of installation of the unit.
When the unit is powered on or off, a message is
displayed.The user can turn this message display
on or off.
The factory default setting is “6”. (Adjustment level:
1 to 11)
The factory default setting is “ON”.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection display.
2. Press the right or left side of SEARCH button
2. Press the right or left side of SEARCH button
% to select “MESSAGE”.
% to select “CONTRAST”.
3. Press ENT button 2 .
3. Press ENT button 2 .
4. Turn the Rotary knob & clockwise to set the
message display to “ON”; turn it counterclockwise
to set the message display to “OFF”.
4. Turn the Rotary knob & clockwise or
counterclockwise to adjust the contrast.
5. Pressing ENT button 2 returns to the
5. Pressing ENT button 2 returns to the
adjustment selection display.
adjustment selection display.
6. Press ADJ button 4 to return to the previous
6. Press ADJ button 4 to return to the previous mode.
mode.
NON-FADER output adjustment display on/off
If you do not want to adjust the non-fader output
level, you can turn off the “NON-FAD VOL” display.
Setting the SEARCH button
illumination color (Prism function)
The change in the SEARCH button illumination
color according to the unit operating state is
called the “Prism function”. You can set the
illumination pattern you prefer.
The factory default setting is “ON”.
Even if you set the level adjustment display to
“OFF”, a signal is output from the non-fader output.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection display.
The factory default setting is “PATTERN 1”.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
2. Press the right or left side of SEARCH button
% to select “NON-FADER”.
3. Press ENT button 2 .
2. Press the right or left side of SEARCH button
4. Turn the Rotary knob & clockwise to set the
non-fader output adjustment display to “ON”;
turn it counterclockwise to set the non-fader
output adjustment display to “OFF”.
% to select “PRISM KEY”.
3. Press ENT button 2 .
4. Turn the Rotary knob & clockwise or
counterclockwise to set the illumination
pattern. Each time you turn the Rotary knob
& , the illumination pattern changes in the
following order:
ON:
When A-M button $ is pressed, the “NON-
FAD VOL” item is displayed.
You can adjust the output level.
PATTERN 1 ➜ PATTERN 2 ➜ OFF ➜
PATTERN 1...
OFF:
Even when you press A-M button $ , the
“NON-FAD VOL” item is not displayed.
PATTERN 1:
The color changes for each function mode,
station tuning, scanning and other operations.
You cannot adjust the output level.
5. Pressing ENT button 2 returns to the
adjustment selection display.
PATTERN 2:
In addition to the changes in Pattern 1, the
color changes according to the audio level.
6. Press ADJ button 4 to return to the previous mode.
Triggered audio mute for cellular telephones
OFF:
This unit requires special wiring to mute the audio
signal automatically when a cellular telephone
rings in the car.
The color changes according to the function
mode.
5. Pressing ENT button 2 returns to the
This function is not compatible with all cellular
telephones. Contact your local authorized Clarion
dealer for information on proper installation and
compatibility.
adjustment selection display.
6. Press ADJ button 4 to return to the previous
mode.
17
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
8. OPERATIONS OF ACCESSORIES
CD Changer Operations
CD changer functions
Selecting a CD
When an optional CD changer is connected
through the CeNET cable, this unit controls all
the CD changer functions.This unit can control a
total of 2 changers (MD and/or CD).
Each of the Direct button 9 corresponds to a
disc loaded into the magazine.
➜➜Selecting a disc from 1 to 6
Press the corresponding Direct button 9 (1 to
Press FNC button 3 and select the CD changer
mode to start play. If 2 CD changers are
connected, press FNC button 3 to select the
CD changer for play.
6)to select the desired disc.
➜ Selecting a disc from 7 to 12 (only when a
12 disc CD changer is used.)
Press and hold the corresponding Direct button
If “NO MAGAZINE” appears in the display, insert
the magazine into the CD changer.“DISC CHECK”
appears in the display while the player loads
(checks) the magazine.
If “NO DISC” appears in the display, eject the
magazine and insert discs into each slot. Then,
reinsert the magazine back into the CD changer.
9
(7 to 12) for 1 second or longer to select the
desired disc.
If a CD is not loaded in a slot of the magazine,
pressing the Direct button 9 corresponding to its
disc number is invalid.
Selecting a track
➜➜Track-up
CAUTION
1. Press the right side of SEARCH button % to
CD-ROM discs cannot be played in the CD
changer.
move ahead to the beginning of the next track.
2. Each time you press the right side of SEARCH
button % , the track advances ahead to the
beginning of the next track.
Pausing play
1. Press Play/pause button 2 to pause play.
“PAUSE” appears in the display.
➜➜Track-down
1. Press the left side of SEARCH button % to
move back to the beginning of the current
track.
2. To resume play, press Play/pause button 2
again.
2. Press the left side of SEARCH button % twice
Displaying CD titles
This unit can display title data for CD-text CDs
and user titles input with this unit.
to move to the beginning of the previous track.
Fast-forward/fast-backward
1. Press DISP button ! to display the title.
➜➜Fast-forward
2. Each time you press and hold DISP button
Press and hold the right side of SEARCH button
!
for 1 second or longer, the title display
% for 1 second or longer.
changes in the following order:
➜➜Fast-backward
User title (disc) ➜ CD-text title (disc) ➜ CD-
text title (track) ➜ user title (disc)...
Press and hold the left side of SEARCH button
Note:
% for 1 second or longer.
• If the CD playing is not a CD-text CD or no user
title has been input, “NO-TTL” appears in the
display.
➜➜Scrolling a CD-text title
When a CD-text title is longer than 11 characters,
you can scroll the display as follows.
1. Display the CD-text title (disc or track).
2. Press TITLE button 4 . The title scrolls.
18
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
CD Changer Operations
Disc repeat play
Top function
The top function plays from the first track (track
No. 1) of the disc.
After all the tracks on the current disc have been
played, the disc repeat play automatically replays
the current disc over from the first track. This
function continues automatically until it is
canceled.
➜➜When playing a disc 1 to 6
Press the Direct button 9 (1 to 6) with the same
number as the CD playing.
1. Press and hold RPT button 6 for 1 second
or longer.“DISC” and “RPT” light in the display
and the disc repeat play starts.
➜➜When playing a disc 7 to 12 (only when a
12 disc CD changer is used.)
Press and hold for 1 second or longer the Direct
button 9 (7 to 12) with the same number as the
CD playing.
2. To cancel the disc repeat play, press and hold
RPT button 6 again. “DISC” and “RPT” go
off from the display and normal play resumes
on the current track.
If a CD is not loaded in a slot of the magazine,
pressing the Direct button 9 corresponding to its
disc number is invalid.
Random play
The random play selects and plays individual
tracks on the disc in no particular order. This
function continues automatically until it is
canceled.
Scan play
The scan play locates and plays the first 10
seconds of each track on a disc automatically.
This function continues on the disc until it is
canceled.
1. Press RDM button 7 . “RDM” lights in the
display and the random play begins.
The scan play is useful when you want to select a
desired track.
2. To cancel the random play, press RDM button
1. Press SCN button 5 to start track scanning.
“SCN” lights in the display.
7
again.“RDM” goes off from the display and
normal play resumes.
2. To cancel the scan play, press SCN button 5
again. “SCN” goes off from the display and
the current track continues to play.
Disc random play
The disc random play selects and plays individual
tracks or discs automatically in no particular
order. This function continues automatically until
it is canceled.
Disc scan play
The disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected CD changer. This function
continues automatically until it is canceled.
1. Press and hold RDM button 7 for 1 second
or longer.“DISC” and “RDM” light in the display
and the disc random play starts.
The disc scan play is useful when you want to
select a desired CD.
2. To cancel the disc random play, press and hold
RDM button 7 again. “DISC” and “RDM” go
off from the display and normal play resumes
from the current track.
1. Press and hold SCN button 5 for 1 second
or longer.“DISC” and “SCN”light in the display
and the disc scan play starts.
2. To cancel the disc scan play, press SCN button
5
again. “DISC” and “SCN” go off from the
display and the current track continues to play.
Repeat play
The repeat play continuously plays the current
track. This function continues automatically until
it is canceled.
1. Press RPT button 6 . “RPT” lights in the
display and the current track is repeated.
2. To cancel the repeat play, press RPT button
6
again. “RPT” goes off from the display and
normal play resumes.
19
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
MD Changer Operations
2. Each time you press the right side of SEARCH
button % , the track advances ahead to the
beginning of the next track.
MD changer functions
When an optional MD changer is connected
through the CeNET cable, this unit controls all
the MD changer functions. This unit can control
a total of 2 changers (MD and/or CD).
➜➜Track-down
1. Press the left side of SEARCH button % to
move back to the beginning of the current track.
Press FNC button 3 and select the MD changer
mode to start play. If 2 MD changers are
connected, press FNC button 3 to select the
MD changer for play.
2. Press the left side of SEARCH button % twice
to move to the beginning of the previous track.
If “NO DISC” appears in the display, load MDs
into the MD changer.
Fast-forward/fast-backward
➜➜Fast-forward
Press and hold the right side of SEARCH button
% for 1 second or longer.
Pausing play
1. Press Play/pause button 2 to pause play.
“PAUSE” appears in the display.
➜➜Fast-backward
Press and hold the left side of SEARCH button
% for 1 second or longer.
2. To resume play, press Play/pause button 2
again.
Top function
Switching disc titles and track titles
The top function plays from the first track (track
No. 1) of the disc. Press the Direct button 9 (1
to 6) with the same number as the MD playing.
This unit can display disc titles and track titles
already entered on MDs. Titles up to 128
characters long can be displayed by scrolling the
titles.
If an MD is not loaded in a slot of the MD changer,
pressing the Direct button 9 corresponding to its
disc number is invalid.
Titles cannot be entered for MDs with this unit.
1. Press DISP button ! to display the title. The
disc title or track title is displayed.
Scan play
The scan play locates and plays the first 10
seconds of each track on a disc automatically.This
function continues on the disc until it is canceled.
2. Each time you press and hold DISP button
!
for 1 second or longer, the display toggles
between the disc title and the track title.
The scan play is useful when you want to select a
desired track.
➜Scrolling titles
When a title is longer than 11 characters, you
can scroll through it with the following operation.
1. Press SCN button 5 to start track scanning.
“SCN” lights in the display.
1. Display the MD title (disc or track).
2. Press TITLE button 4 .
2. To cancel the scan play, press SCN button 5
again. “SCN” goes off from the display and
the current track continues to play.
The display scrolls through the title.
Selecting an MD
Disc scan play
Each of the Direct button 9 corresponds to an
MD loaded into the MD changer. Press the
corresponding Direct button 9 (1 to 6) to select
the desired disc.
The disc scan play locates and plays the first 10
seconds of the first track on each disc in the
currently selected MD changer. This function
continues automatically until it is canceled.
If an MD is not loaded in a slot of the MD changer,
pressing the Direct button 9 corresponding to its
disc number is invalid.
The disc scan play is useful when you want to
select a desired MD.
1. Press and hold SCN button 5 for 1 second
or longer.“DISC”and “SCN” light in the display
and the disc scan play starts.
Selecting a track
➜➜Track-up
2. To cancel the disc scan play, press and hold
SCN button 5 again. “DISC” and “SCN” go
off from the display and the current track
continues to play.
1. Press the right side of SEARCH button % to
move ahead to the beginning of the next track.
20
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
MD Changer Operations
Repeat play
TV Operations
TV tuner functions
The repeat play continuously plays the current
track. This function continues automatically until
it is canceled.
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV requires a TV tuner and
monitor.
1. Press RPT button 6 . “RPT” lights in the
display and the current track is repeated.
Watching a TV
2. To cancel the repeat play, press RPT button
6
again. “RPT” goes off from the display and
1. Press FNC button 3 and select the TV mode.
normal play resumes.
2. Press BND button # to select the desired TV
band (TV1 or TV2). Each time the button is
pressed, the input selection toggles between
TV1 and TV2.
Disc repeat play
After all the tracks on the current disc have been
played, the disc repeat play automatically replays
the current disc over from the first track. This
function continues automatically until it is
canceled.
3. Press the right or left side of SEARCH button
% to tune in the desired TV station.
Watching a video
1. Press and hold RPT button 6 for 1 second
or longer.“DISC” and “RPT” light in the display
and the disc repeat play starts.
The TV tuner has a VTR input terminal to which
1 external device can be connected. Connect a
12V video cassette player (VCP) or video
cassette recorder (VCR) to the TV tuner input
terminal.
2. To cancel the disc repeat play, press and hold
RPT button 6 again. “DISC” and “RPT” go
off from the display and normal play resumes
on the current track.
1. Press RDM button 7 to select VTR.
2. To return to the TV broadcast, press RDM
button 7 .
Random play
The random play selects and plays individual
tracks on the disc in no particular order. This
function continues automatically until it is
canceled.
Tuning
There are 3 types of tuning mode available, Seek
tuning, manual tuning and preset tuning.
1. Press RDM button 7 . “RDM” lights in the
Seek tuning
1. Press BND button # and select the desired
display and the random play begins.
2. To cancel the random play, press RDM button
TV band (TV1 or TV2).
7
again.“RDM” goes off from the display and
If “MANU” is lit in the display, press and hold
BND button # for 1 second or longer. “MANU”
in the display goes off and seek tuning is now
available.
normal play resumes.
Disc random play
2. Press the right or left side of SEARCH button
The disc random play selects and plays individual
tracks or discs automatically in no particular
order.This function continues automatically until
it is canceled.
% to automatically seek a station.
Press the right side of SEARCH button % to
automatically tune up the frequency band to
the next available TV station; press the left
side to automatically tune down.
1. Press and hold RDM button 7 for 1 second
or longer.“DISC”and “RDM”light in the display
and the disc random play starts.
2. To cancel the disc random play, press and hold
RDM button 7 again. “DISC” and “RDM” go
off from the display and normal play resumes
from the current track.
21
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
TV Operations
Manual tuning
There are 2 ways available:Quick tuning and step
tuning.
only the strong stations are stored into memory.
1. Press BND button # and select the desired
TV band (TV1 or TV2).
2. Press and hold AS button 5 for 2 seconds or
longer. The stations with good reception are
automatically stored to the Preset buttons 9 .
When you are in the step tuning mode, the
frequency changes one step at a time. In quick
tuning mode, you can quickly tune the desired
frequency.
Preset scan
1. Press BND button # and select the desired
band (TV1 or TV2).
Preset scan allows the user to view each preset
position before it automatically advances to the
next preset. This function is useful for searching
for desired TV station in memory.
If “MANU” is not lit in the display, press and
hold BND button # for 1 second or longer.
“MANU” is lights in the display and manual
tuning is now available.
1. Press PS button 5 .
2. Tune into a station.
2. When the desired station is found, press PS
➜ Quick tuning:
button 5 again to remain tuned to that station.
Press and hold the right or left side of
SEARCH button % for 1 second or longer to
tune in a station.
Note:
• Do not press and hold PS button 5 for 2 seconds
or longer. Doing so will trigger the auto store
function and start storing stations into memory.
➜ Step tuning:
Press the right or left side of SEARCH button
% to manually tune in a station.
Setting the TV diver
You can change the reception setting for the TV
antenna connected to the TV tuner.
Recalling a preset station
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
A total of 12 TV stations can be stored (6-TV1
and 6-TV2).This allows you to select your favorite
TV stations and store them in memory for later
recall.
2. Press the right or left side of SEARCH button
% to select “TV DIVER”.
1. Press BND button # and select the desired
TV band (TV1 or TV2).
3. Press ENT button 2 .
2. To recall a storedTV station, press the desired
4. Turn the Rotary knob & clockwise to set to
“ON” or counterclockwise to set to “OFF”.
Preset button 9 to select that station.
Press and hold one of the Preset buttons 9
for 2 seconds or longer to store the current
station into the preset memory.
ON:
Sets reception emphasizing the visual.
OFF:
Sets the diver setting to OFF.
5. Press ENT button 2 .
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
6. Press ADJ button 4 to return to the previous
mode.
2. Press and hold one of the Preset buttons 9
for 2 seconds or longer to store the current
station to that preset memory.
Auto store
Auto store selects 6TV stations automatically and
stores each one into a preset memory.
If there are not 6 stations with good reception,
stations previously stored in memory remain and
22
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
DSP Operations
DSP control function
4. Turn the Rotary knob & clockwise or
counterclockwise to set the sensitivity of the
spectrum analyzer.
If the DSP (DPH7500z), sold separately, is
connected to this unit using the CeNET cable,
all the functions of the DSP can be controlled.
You can choose one of “LOW”, “MID-LOW”,
“MID”, “MID-HIGH” or “HIGH” for the
sensitivity of the spectrum analyzer.
DSP functions
5. Pressing ENT button 2 returns to the
There are 2 modes available in DPH7500z, easy
mode and professional mode. Choose one of
them and adjust the sound field and the sound
quality.
adjustment selection display.
6. Press ADJ button 4 to return to the previous
mode.
• Functions common to each mode:
Spectrum analyzer display, auto loudness, etc.
• Easy mode:
Output adjustment of auto loudness,
subwoofer and playback band
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
Adjustment using the graphic equalizer function
and the DSP function.
• Professional mode:
2. Press the right or left side of SEARCH button
Adjustment using the space equalizer function
and the parametric equalizer function.
% to select “SOUND”.
3. Press ENT button 2 .
When the easy mode is selected, adjustment for
the professional mode cannot be made. On the
contrary, when the professional mode is selected,
adjustment for the easy mode cannot be made.
For details on functions of each mode, refer to
the owner’s manual supplied with the
DPH7500z.
Hereafter the graphic equalizer is referred to as a
G.EQ., the space equalizer referred to as S.EQ.
and the parametric equalizer referred to as P.EQ.
4. Press the right or left side of SEARCH button
% to select the adjustment item.
There are “A.LD LEVEL”, “WOOFER OUT”,
“WOOFER LPF”, “HPF” and “TEST TONE”
available for the adjustment items.
For details on each adjustment item, refer to the
owner’s manual supplied with the DPH7500z.
5. Turn the Rotary knob & clockwise or
counterclockwise to make the adjustment.
Operations common to each mode
Enjoying a spectrum analyzer
This unit can display the spectrum analyzer.
There are 8 spectrum analyzer patterns.
6. Pressing ENT button 2 returns to the
adjustment selection display.
7. Press ADJ button 4 to return to the previous
mode.
1. Press DISP button ! to select the spectrum
Selecting easy mode or professional
mode
The factory default setting is “EASY”.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
analyzer display.
2. Each time you press and hold DISP button
!
for 1 second or longer, the spectrum
analyzer patterns are switched.
Setting the sensitivity of the
spectrum analyzer
2. Press the right or left side of SEARCH button
% to select “DSP/EQ SEL”.
The factory default setting is “MID”.
1. Press and hold ADJ button 4 for 1 second or
longer to switch to the adjustment selection
display.
3. Press ENT button 2 .
4. Turn the Rotary knob & clockwise or
counterclockwise to set the mode to “EASY”
or “PRO”.
2. Press the right or left side of SEARCH button
5. Pressing ENT button 2 returns to the
% to select “ANA SENS”.
adjustment selection display.
3. Press ENT button 2 .
6. Press ADJ button 4 to return to the previous
mode.
23
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
DSP Operations
Inputting a title
Selecting a G.EQ menu
You can give a title to the user memory of the
DSP, G.EQ, S.EQ and P.EQ that you have
adjusted yourself.
1. Press A-M button $ and select “G.EQ”.
“G.EQ” blinks in the display.
2. Press BND button # to select “BASC” (basic).
“BASC” appears in the function mode
indication # .
1. Press A-M button $ to select the adjustment
mode in which you want to give a title.
2. Press BND button # to select “USER”.
“USER” appears in the function mode
indication # .
3. Press one of the Direct buttons 9 and select
the desired G.EQ menu.
To select the user memory, press BND button
#
to select “USER” and press one of the Direct
3. Press one of the Preset buttons 9 to select
the user memory to which you want to give a
title.
buttons 9 .
Editing/storing a G.EQ menu (User
memory)
1. Select a G.EQ menu which you want to edit
on the basis of.
4. Press TITLE button 4 .
5. Press the right or left side of SEARCH button
% to move the cursor.
6. Press DISP button ! to select a character.
2. Press and hold ADJ button 4 for 1 second or
There are capital letters, small letters,
numbers, symbols and umlaut available for
the character.
longer.
3. Press the right or left side of SEARCH button
% to select the frequency to be adjusted.
There are 50Hz, 100Hz, 200Hz, 400Hz, 1kHz,
3kHz and 12kHz available for the adjustment
frequency.
7. Turn the Rotary knob & clockwise or
counterclockwise to select the character you
want to input.
8. Repeat steps 5 to 7 to input the title.
For details on each adjustment item, refer to the
owner’s manual supplied with the DPH7500z.
9. Press and hold ENT button 2 for 2 seconds
or longer to put the title into memory.The title
input mode is canceled.
4. Turn the Rotary knob & clockwise or
counterclockwise to make the adjustment.The
adjustment range is from –12dB to +12dB.
Easy mode/G.EQ operations
5. Repeat steps 3 to 4 to complete the
adjustment and press ADJ button 4 .
Note:
6. Press and hold one of the Direct buttons 9
for 2 seconds or longer to store the edited
contents.
• The adjustment made in easy mode is not reflected
in the adjustment in professional mode. On the
contrary, the adjustment made in professional
mode is not reflected in the adjustment in easy
mode.
You can give a title to the user memory. For the
inputting method of titles, refer to the subsection
“Inputting a title” in the “Operations common
to each mode”.
G.EQ effect on/off
While the “G.EQ” indication 4 is lit in the display,
the G.EQ effect is set to “ON”.
Easy mode/DSP operations
The factory default setting is “ON”.
DSP effect on/off
When the “DSP” indication 5 is lit in the display,
the DSP effect is set to “ON”.
1
Press A-M button $ and select “G.EQ”.While
“G.EQ” is selected, “G.EQ” blinks in the
display.
The factory default setting is “ON”.
2. Press DISP button ! .
1. Press A-M button $ and select “DSP”. While
“DSP” is selected, “DSP” blinks in the display.
3. Press A-M button $ . “G.EQ” in the display is
changed from blinking to lit or unlit.
2. Press DISP button ! .
When “G.EQ” is unlit, the G.EQ effect is set to
OFF.
Note:
3. Press A-M button $ . “DSP” in the display is
changed from blinking to lit or unlit.
When “DSP” is unlit, the DSP effect is set to OFF.
• If the G.EQ effect is set to OFF, the adjustment
made in the “G.EQ operations” is not reflected in
the music source.
24
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
DSP Operations
Note:
and HIGH or LIVENESS available for the items
to be adjusted.
• If the DSP effect is set to OFF, the adjustment
made in the “DSP operations” is not reflected in
the music source.
For details on each adjustment item, refer to the
owner’s manual supplied with the DPH7500z.
4. Turn the Rotary knob & clockwise or
Setting a listening position menu
counterclockwise to make the adjustment.
1. Press A-M button $ and select “DSP”. “DSP”
5. Repeat steps 3 to 4 to complete the
blinks in the display.
adjustment and press ADJ button 4 .
2. Press the right or left side of SEARCH button
6. Press and hold one of the Direct buttons 9
for 2 seconds or longer to store the edited
contents.
% to set the listening position type.
There are FULL SEAT, FRONT-RIGHT (only
right seat), FRONT-LEFT (only left seat),
FRONT (only front seats), REAR (only rear
seats) and PASS available for the listening
position types.
You can give a title to the user memory. For
the inputting method of titles, refer to the
subsection “Inputting
a
title” in the
“Operations common to each mode”.
The factory default setting is “FULL SEAT”.
Professional mode/S.EQ operations
Making fine adjustment of the
listening position
1. Upon completion of setting the listening
Note:
• The adjustment made in professional mode is not
reflected in the adjustment in easy mode. On the
contrary, the adjustment made in easy mode is
not reflected in the adjustment in professional
mode.
position, press ENT button 2 .
2. Press the right or left side of SEARCH button
% to select “BAL” or “FAD”.The selected item
blinks.
S.EQ effect on/off
While the “S.EQ” indication 8 is lit in the display,
the S.EQ effect is set to “ON”.
3. Turn the Rotary knob & clockwise or
counterclockwise to adjust the balance and
the fader.
The factory default setting is “ON”.
1. Press A-M button $ and select “S.EQ”.While
“S.EQ” is selected, “S.EQ” blinks in the
display.
4. Press ENT button 2 to return to the DSP
mode.
Selecting a sound field menu
1. Press A-M button $ and select “DSP”. “DSP”
2. Press DISP button ! .
3. Press A-M button $ . “S.EQ” in the display is
blinks in the display.
changed from blinking to lit or unlit.
2. Press BND button # to select “B-1” (basic-1)
or “B-2” (basic-2). “B-1” or “B-2” appears in
the function mode indication # .
When “S.EQ” is unlit, the S.EQ effect is set to
OFF.
Note:
3. Press one of the Direct buttons 9 and select
• If the S.EQ effect is set to OFF, the adjustment
made in the “S.EQ operations” is not reflected in
the music source.
the desired sound field menu.
To select the user memory, press BND button
#
to select “USER” and press one of the Direct
buttons 9 .
Selecting a S.EQ menu
1. Press A-M button $ and select “S.EQ”.
“S.EQ” blinks in the display.
Editing/storing a sound field menu
1. Select a sound field menu which you want to
edit on the basis of.
2. Press BND button # to select “BASC” (basic).
“BASC” appears in the function mode
indication # .
2. Press and hold ADJ button 4 for 1 second or
longer.
3. Press one of the Direct buttons 9 and select
the desired S.EQ menu.
3. Press the right or left side of SEARCH button
% to select the item to be adjusted.
To select the user memory, press BND button
#
to select “USER” and press one of the Direct
There are EFFECT LEVEL, INITIAL DELAY,
REAR MIX, REVERB TIME or ROOM SIZE
buttons 9 .
25
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
DSP Operations
Editing/storing a S.EQ menu (User
memory)
Selecting a P.EQ menu
1. Press A-M button $ and select “P.EQ”. “P.EQ”
blinks in the display.
1. Select a S.EQ menu which you want to edit
on the basis of.
2. Press BND button # to select “BASC” (basic).
“BASC” appears in the function mode
indication # .
2. Press and hold ADJ button 4 for 1 second or
longer.
3. Press one of the Direct buttons 9 and select
3. Press the right or left side of SEARCH button
the desired P.EQ menu.
% to select the item to be adjusted.
To select the user memory, press BND button
There are DIFFUZE, CAR WIDTH and CAR
LENGTH available for the items to be adjusted.
#
to select “USER” and press one of the Direct
buttons 9 .
For details on each adjustment item, refer to the
owner’s manual supplied with the DPH7500z.
Editing/storing a P.EQ menu (User
memory)
1. Select a P.EQ menu which you want to edit
on the basis of.
4. Turn the Rotary knob & clockwise or
counterclockwise to make the adjustment.The
adjustment range is from 1 to 10 for each item.
5. Repeat steps 3 to 4 to complete the
2. Press and hold ADJ button 4 for 1 second or
adjustment and press ADJ button 4 .
longer.
6. Press and hold one of the Direct buttons 9
for 2 seconds or longer to store the edited
contents.
3. Press the right or left side of SEARCH button
% to select the item to be adjusted.
There are correction channel, correction band,
selection of the center frequency, gain
adjustment and selection of the Q-curve
available for the items to be adjusted.
You can give a title to the user memory. For
the inputting method of titles, refer to the
subsection “Inputting
a
title” in the
“Operations common to each mode”.
For details on each adjustment item, refer to the
owner’s manual supplied with the DPH7500z.
Professional mode/P.EQ operations
4. Turn the Rotary knob & clockwise or
P.EQ effect on/off
While the “P.EQ” indication 7 is lit in the display,
the P.EQ effect is set to “ON”.
counterclockwise to make the adjustment.
5. Repeat steps 3 to 4 to complete the
adjustment and press ADJ button 4 .
The factory default setting is “ON”.
6. Press and hold one of the Direct buttons 9
for 2 seconds or longer to store the edited
contents.
1. Press A-M button $ and select “P.EQ”.While
“P.EQ” is selected, “P.EQ”blinks in the display.
2. Press DISP button ! .
You can give a title to the user memory. For
the inputting method of titles, refer to the
3. Press A-M button $ . “P.EQ” in the display is
changed from blinking to lit or unlit.
subsection “Inputting
“Operations common to each mode”.
a
title” in the
When “P.EQ” is unlit, the P.EQ effect is set to OFF.
Note:
• If the P.EQ effect is set to OFF, the adjustment
made in the “P.EQ operations” is not reflected in
the music source.
26
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
9. TROUBLESHOOTING
Problem
Cause
Measure
Power does not
turn on.
Fuse is blown.
Replace with a fuse of the same amperage. If the
fuse blows again, consult your store of purchase.
(No sound is
produced.)
Incorrect wiring.
Consult your store of purchase.
No sound output Power antenna lead is
1. Turn the unit off.
when operating
the unit with
amplifiers or
power antenna
attached.
shorted to ground or
2. Remove all wires attached to the power antenna
lead. Check each wire for a possible short to
ground using an ohm meter.
excessive current is required
for remote-on the amplifiers
or power antenna.
3. Turn the unit back on.
4. Reconnect each amplifier remote wire to the
power antenna lead one by one. If the amplifiers
turn off before all wires are attached, use an
external relay to provide remote-on voltage
(excessive current required).
Nothing happens The microprocessor has
when buttons are malfunctioned due to noise,
Turn off the power, then press the OPEN button 1
and remove the DCP.
Press the reset button for about 2 seconds with a thin
pressed.
etc.
rod.
Reset button
Display is not
accurate.
DCP or source unit
connectors are dirty.
Wipe the dirt off with a soft cloth moistened with
cleaning alcohol.
Compact disc
Another compact disc is
Eject the compact disc before loading the new one.
cannot be loaded. already loaded.
Sound skips or is Compact disc is dirty.
noisy.
Clean the compact disc with a soft cloth.
Compact disc is heavily
scratched or warped.
Replace with a compact disc with no scratches.
Sound is bad
directly after
power is turned
on.
Water droplets may form on
the internal lens when the
car is parked in a humid
place.
Let dry for about 1 hour with the power on.
27
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
10. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
Cause
Error Display
ERROR 2
Measure
A CD is caught inside the CD deck and is
not ejected.
This is a failure of CD deck’s mechanism
and consult your store of purchase.
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR H
A CD cannot be played due to scratches,
etc.
Replace with a non-scratched,
non-warped-disc.
A CD is loaded upside-down inside the CD Eject the disc then reload it properly.
deck and does not play.
A CD inside the CD changer is not loaded. This is a failure of CD changer’s mecha-
nism and consult your store of purchase.
A CD inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-warped
disc.
A CD inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Displayed when the temperature in the
MD changer is too high and playback has
been stopped automatically.
Lower the surrounding temperature and
wait for a while to cool off MD changer.
ERROR 2
ERROR 3
ERROR 6
An MD inside the MD changer is not
loaded.
This is a failure of MD changer’s mecha-
nism and consult your store of purchase.
An MD inside the MD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-warped
disc.
An MD inside the MD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Displayed when a non-recorded MD is
loaded in the MD changer.
Load a pre-recorded MD in the MD
changer.
If an error display other than the ones described above appears, press the reset button. If the problem
persists, turn off the power and consult your store of purchase.
28
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
11. SPECIFICATIONS
FM Tuner
Frequency Range:
87.9 MHz to 107.9 MHz
Audio
Maximum Power Output:
180 W (45 W × 4 ch) (EIAJ)
Usable Sensitivity:
11 dBf
Continuous Average Power Output:
17 W × 4, into 4 Ω, 20 Hz to 20 kHz, 1%THD
50dB Quieting Sensitivity:
17 dBf
Bass Control Action (30 Hz):
±15 dB
Alternate Channel Selectivity:
75 dB
Treble Control Action (10 kHz):
±10 dB
Stereo Separation (1 kHz):
35 dB
Line Output Level (CD 1 kHz):
4 V
Frequency Response (±3 dB):
30 Hz to 15 kHz
General
Power Supply Voltage:
14.4 V DC (10.8 to 15.6 V allowable),
negative ground
AM Tuner
Frequency Range:
530 kHz to 1710 kHz
Current Consumption:
Less than 15 A
Usable Sensitivity:
25 µV
Speaker Impedance:
4 Ω (4 Ω to 8 Ω allowable)
CD Player
System:
Weight / Source unit:
3.75 lb. (1.7 kg)
Compact disc digital audio system
Weight / Remote control unit:
1 oz. (30 g) (including battery)
Usable Discs:
Compact disc
Dimensions / Source unit:
7" (Width) × 2" (Height) × 6-1/8" (Depth)
[178 (W) × 50 (H) × 155 (D) mm]
Frequency Response (±1 dB):
5 Hz to 20 kHz
Dimensions / Remote control unit:
1-3/4" (Width) × 4-5/16" (Height) × 1-1/8" (Depth)
[44 (W) × 110 (H) × 27 (D) mm]
Signal to Noise Ratio (1 kHz):
100 dB
Dynamic Range (1 kHz):
95 dB
Harmonic Distortion:
0.01%
Notes:
• Specifications comply with EIA Standards.
• Specifications and design are subject to change without notice for further improvement.
29
Download from Www.Somanuals.com. All Manuals Search And Download.DRX8 6 7 5 z
Memo
30
DRX8 6 7 5 zDownload from Www.Somanuals.com. All Manuals Search And Download.
|