Cisco Media Gateway Controller Software
Release 9 Billing Interface Guide
December, 2007
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-1089-11
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
C H A P T E R
1
Detailed CDB Description 1-21
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
User Service Information (Tag: 3001/ITU) 1-69
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
LNP Dip (Tag: 4029) 1-105
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Furnish Charging Information (Tag: 4079) 1-123
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Partial Calling Line Identity (Tag: 4220) 1-144
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Cisco Reserved CDEs 1-162
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
C H A P T E R
2
A P P E N D I X
A
CDE Changes in Release 9.7 A-8
I
N D E X
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
•
•
•
•
•
•
•
•
Obtaining Documentation, Obtaining Support, and Security Guidelines, page xvii
Summary History of Document Changes, page xvii
Document Objective
This guide provides reference information for the Cisco Media Gateway Controller (MGC) software
Release 9. You should read the system-level documentation supplied with your system before using this
guide. A complete list of these documents is included in the Cisco Media Gateway Controller Software
Release 9 Installation and Configuration Guide that ships with your system.
Note
This guide uses the term Media Gateway Controller software or MGC application to mean the
Cisco MGC software that runs in the UNIX environment on a server. The term MGC refers to the
combination of this software and the server. The MGC communicates with the SS7 network to process
and route calls between a traditional time-division multiplexing (TDM) network and a packet data
network. This routing takes place through a variety of media gateways (MGWs), which are separate
devices that perform the conversion between the TDM and data network formats.
Audience
This guide is for network operators and administrators who have experience with telecommunications
networks, protocols, and equipment and who have familiarity with data communications networks,
protocols, and equipment.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Document Organization
The major sections of this guide are summarized in Table 1.
Table 1
Document Organization
Chapter
Title
Description
1
Billing Interfaces
Describes the Cisco MGC billing interface
capabilities and its call detail records (CDRs).
2
Info Field Reference
Provides additional information about the MGC
Info Field (Tag 4031).
Appendix A
CDE Listings by
Release
Lists the call detail element (CDE) changes made
for each release.
Document Conventions
Throughout this guide, $BASEDIR refers to the directory structure in which the Cisco MGC software is
installed. $BASEDIR is a UNIX environment variable that must be set during installation. Refer to the
this environment variable.
Text conventions used in this guide are shown in Table 2.
Table 2
Conventions
Convention
Meaning
Description/Comments
Boldface
Commands and keywords
you enter as shown
offset-list
Italics
Variables for which you
supply values
command type interface
You replace the variable with the type
of interface.
In contexts that do not allow italics,
such as online help, arguments are
enclosed in angle brackets (< >).
Square brackets ([ ])
Vertical bars ( | )
Braces ({ })
Optional elements
command [abc]
abc is optional (not required), but you
can choose it.
Separated alternative
elements
command [abc | def]
You can choose either abc or def, or
neither, but not both.
Required choices
command {abc | def}
You must choose either abc or def, but
not both.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 2
Conventions (continued)
Convention
Meaning
Description/Comments
Braces and vertical bars
within square brackets
([ { | } ])
A required choice within an command [abc {def | ghi}]
optional element
You have three options:
Nothing
abc def
abc ghi
Caret character (^)
Control key
A string
The key combinations ^D and Ctrl-D
are equivalent: Both mean “hold down
the Control key while you press the D
key.” Keys are indicated in capital
letters, but are not case sensitive.
A nonquoted set of
characters
For example, when setting an SNMP
community string to public, do not use
quotation marks around the string;
otherwise, the string will include the
quotation marks.
System prompts
Denotes interactive
The system prompt indicates the
sessions, indicates that the
current command mode. For example,
user enters commands at the the prompt Router (config) #
prompt
indicates global configuration mode.
Screenfont
Terminal sessions and
information the system
displays
Angle brackets (< >)
Nonprinting characters such
as passwords
Exclamation point (!) at the A comment line
beginning of a line
Comments are sometimes displayed by
the Cisco IOS software.
Caution
Means reader be careful. In this situation, you might do something that could result in equipment
damage or loss of data.
Timesaver
Note
Means reader may be able to save some time. Taking the action described could achieve a result in less
time than might be achieved otherwise.
Means reader take note. Notes contain helpful suggestions or references to material not covered in the
manual.
Conventions used in the Cisco MGC system (such as in MML commands) are shown in Table 3.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 3
Data Type Conventions
Data Type
Definition
Example
123
000123
4200000000
Integer
A series of decimal digits from the set of 0 through 9 that
represents a positive integer. An integer can have one or
more leading zero digits (0) added to the left side to align
the columns. Leading zeros are always valid as long as
the number of digits is less than or equal to ten. Values of
this type have a range of 0 through 4294967295.
123
Signed
integer
This data type has the same basic format as the integer
but can be either positive or negative. When negative, it
is preceded by the sign character (–). As with the integer
data type, this data type can be as many as ten digits in
length, not including the sign character. The value of this
type has a range of –2147483647 through 2147483647.
–000123
–2100000000l
1f3
01f3000
Hexadecimal A series of 16-based digits from the set of 0 through 9, a
through f, or A through F. The hexadecimal number can
have one or more leading zeros (0) added to the left side.
For all hexadecimal values, the maximum size is
0xffffffff (eight hexadecimal digits).
EntityID
LineSES_Threshold999
Text
A series of alphanumeric characters from the ASCII
character set, where defined. Tab, space, and double
quote (“ ”) characters cannot be used. Text can be as many
as 255 characters; however, it is recommended that you
limit the text to no more than 32 characters for
readability.
“This is a descriptive
string.”
String
A series of alphanumeric characters and white-space
characters. A string is surrounded by double quotes (“ ”).
Strings can be as many as 255 characters; however, it is
recommended that you limit the strings to no more than
80 characters for readability.
Note
Hexadecimal and integer fields in files can have different widths (number of characters) for column
alignment.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
The documents that make up the Cisco MGC documentation set are listed in Table 4.
Table 4
Cisco Media Gateway Controller Documentation Set
Functional Area
Document Title
Document Description
Hardware
Cisco Media Gateway Controller
Hardware Installation Guide
Provides information on how to
install the Cisco SC2200 and
Cisco VSC3000 MGCs
Hardware
Regulatory Compliance and Safety
Information for the Cisco Media
Gateway Controller Hardware
Provides regulatory compliance and
safety information
Software installation
and configuration
Cisco Media Gateway Controller
Software Release 9 Installation and configuration information for the
Provides installation and
Configuration Guide
Cisco MGC software Release 9
Software installation
and configuration
Cisco Media Gateway Controller
Software Release 9 Provisioning
Guide
Provides provisioning information
for the Cisco MGC software
Release 9
Software installation
and configuration
Cisco Media Gateway Controller
Software Release 9 Dial Plan Guide Cisco MGC software Release 9
Provides dial plan information for the
Software installation
and configuration
Cisco Media Gateway Controller Provides reference information for
Software Release 9 Billing Interface the Cisco MGC software Release 9
Guide (this book)
Software installation
and configuration
Cisco Media Gateway Controller
Software Release 9 Operations,
Maintenance, and Troubleshooting
Guide
Provides operation, maintenance,
and troubleshooting information for
the Cisco MGC software Release 9
Software installation
and configuration
Release Notes for Cisco Media
Gateway Controller Software
Release 9
Provides release-specific
information for the Cisco MGC
software Release 9
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Refer to the map in Figure 1 to navigate through the media gateway controller documentation suite.
Figure 1
Documentation Map
Start
Solution Overview
Is
Is
Yes
Yes
MGC host
set up?
gateway
set up?
No
No
Regulatory Compliance and Safety
Information for Cisco MGC
Regulatory Compliance and Safety
Information for Cisco Media Gateway
Cisco MGC Hardware
Installation Guide
Solution Gateway Hardware
Installation Guide
Release Notes for
Solution Gateway Software
Cisco MGC Software Release 9
Installation and Configuration Guide
Cisco MGC Software Release 9
Installation and Configuration Guide
Solution Gateway
Provisioning Guide
End
Cisco MGC Software Release 9
Provisioning Guide
Cisco MGC Software Release 9
Billing Interface Guide *
Cisco MGC Software Release 9
Dial Plan Guide
Cisco MGC Software Release 9 MML
Command Reference Guide *
Cisco Voice Services Provisioning
Tool Version 2.x
Cisco MGC Software Release 9
Messages Reference Guide *
Cisco MGC Software Release 9
Management Information Base Guide *
Cisco MGC Software Release 9 Operations,
Maintenance, and Troubleshooting Guide
* This guide provides useful information
that is not required during installation.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Obtaining Documentation, Obtaining Support, and Security
Guidelines
For information on obtaining documentation, obtaining support, providing documentation feedback,
security guidelines, and also recommended aliases and general Cisco documents, see the monthly
What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical
documentation, at:
Table 5 describes the document changes made after the initial release of the Cisco Media Gateway
Controller Software Release 9 Billing Interface Guide.
Table 5
Summary History of Document Changes
Document Number and Change
Date
Subject
Change Summary
Tag revisioins
Tag revisions
Tag revisions
OL-1089-11, December, 2007
OL-1089-11, October, 2007
OL-1089-11, April 9, 2007
•
•
•
Updated tags in Release 9.6, 9.7
Added tags 4246, 4247, and 4248
Modified information for tags 4201
and 4202.
•
•
Added tags 4236, 4238, 4239,
4240, 4242, 4243, 4244, and 4245.
Tag revisions
Tag revisions
OL-1089-10, March 31, 2006
OL-1089-10, August 5, 2005
Modified information for tags 4098
and 4099 for the Support for DSP
Voice Quality Statistics feature.
•
•
Modified information for tags
4078, 4080, and 6000.
Modified information for tags
4011, 4049, 4050, 4087, 4088,
4215, 4221, and 4223–4225.
•
•
Added tags 2018-2020, 3018-3020,
4227-4233, and 4237.
Modified definitions for CDBs
1070 and 1071.
•
•
•
•
Added CDBs 1210 and 1260
Added the 1071 CDB.
Tag revisions
OL-1089-09, September 23, 2004
Added tags 4234 and 4235.
Removed CDB information from
individual tag tables.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 5
Summary History of Document Changes
Document Number and Change
Date
Subject
Change Summary
Tag revisions
OL-1089-09, May 17, 2004
•
Modified the description of the
1060 CDB.
•
•
Retired tag 4045.
Modified information for tags 4044
and 4073.
•
Added tags 4083–4097,
4213–4226, and 6005.
Tag revisions
Tag revisions
OL-1089-08, January 9, 2004
OL-1089-08, December 3, 2003
•
•
Restored tags 4046 and 4047.
Modified the description of the
1060 CDB.
•
•
•
Reordered the tags, placing them in
numeric order.
Modified the retirement
information for tag 3004.
Modified release information for
tags 4052 and 4053. They are now
listed as “defined for future use.”
•
Added tags 4098 and 4099, which
are part of a Release 9.4(1) patch.
Tag revisions
Tag revisions
OL-1089-08, August 18, 2003
OL-1089-07, June 30, 2003
•
•
•
Added tags 4204–4212.
Retired tag 4033.
Added data value information for
tags 4030 and 4044.
•
Modified the release in which the
3004 tag was retired.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xviii
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 5
Summary History of Document Changes
Document Number and Change
Date
Subject
Change Summary
Tag revisions
OL-1089-07, June 27, 2003
•
Modified CDB information for tag
4081.
•
Modified descriptions for the
following tags:
–
–
–
2006, 2009, 2010, and 2014
2017, 3001, 3002, and 3006
3009, 3010, 4048, and 4060
•
Modified data values for the
following tags:
–
–
–
–
2011, 2012, 2014, and 2016
4013 and 4038—4040
4066—4068 and 4070—4072
4074—4077, 6000, and 6004
•
•
•
•
Modified information and data
values for tags 6100—6104.
Tag revisions
Tag revisions
OL-1089-07, March 14, 2003
OL-1089-07, January 20, 2003
Modified information for tags
2005, 2007, 3007, and 4014.
Added tags 4034–4037, 4068, and
4072 to the 1110 CBD.
Corrected the octet length
information for tags 3011, 3012,
4032, and 4033.
•
•
•
•
•
Added an appendix that identifies
the CDR changes by release.
Tag revisions
Tag revisions
OL-1089-07, December 9, 2002
OL-1089-06, October 9, 2002
Updated the information for tag
3013.
Changed the CDB information for
tag 4081.
Added CDE and CDB information
for tag 4082.
Expanded data value content of the
3008 tag to include detailed cause
code information.
Tag revisions
Tag revision
Tag revisions
OL-1089-06, September 19, 2002
OL-1089-06, September 5, 2002
OL-1089-06, August 20, 2002
•
•
•
Corrected data value information
for tags 4032 and 4033.
Corrected the data value
information for tag 4048.
Corrected CDB information for
tags 3001, 4078, 4079, and 4080.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xix
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 5
Summary History of Document Changes
Document Number and Change
Date
Subject
Change Summary
Tag revisions
OL-1089-06, August 16, 2002
•
•
•
•
Added data value information to
the 3000 series tags from Q.763.
Identified tags 3002, 3004, 4046,
and 4047 as retired.
Corrected the CBD information for
tags 4052 and 4053.
Corrected descriptions for tags
4066–4068, 4070–4072, and
4074–4076.
•
•
Modified the data value
information for the 4100 series tags
to indicate Cisco MGC time.
Modified the data value
information for ANSI Nature of
Address tags to indicate that the
first value is spare.
•
•
•
•
Modified tags to indicate that the
maximum ANSI number is 214.
Tag revisions
OL-1089-06, July 10, 2002
Updated CDB values for tags 4078,
4079, and 4081.
Updated CDB values for tags 4077
and 4080.
New template
Tag revisions
OL-1089-06, July 1, 2002
OL-1089-06, July 1, 2002
Updated this document with the
current user documentation
template.
•
•
•
Removed Tag 5000 from the
listings for CDBs 1090 and 1100.
Replaced Tag 6001 in CDB 1100
with Tag 6002.
Added MGCP as a valid interface
in Tags 4069 and 4073.
Tag revisions
OL-1089-06, May 15, 2002
•
•
Added Tags 4078 through 4081.
Revised Table 1-2
OL-1089-05, April 3, 2002
Removed references to Tags 4064
and 4065.
Tag revisions
OL-1089-04, March 22, 2002
•
Revised data value and general
information for Tags 4034 through
4037.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xx
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Table 5
Summary History of Document Changes
Document Number and Change
Date
Subject
Change Summary
Tag revisions
OL-1089-03, November 27, 2001
OL-1089-02, November 16, 2001
OL-1089-01, October 18, 2001
•
Revised text for last bullet on
page 1-7 and on page 1-8.
•
Removed “(retired in Release
9.0(1))” for Tag 2017 and
Tag 3017.
•
•
•
Added Tag 4203.
Removed Tag 4064 and Tag 4065.
ASCII output
Removed references to ASCII
output on page 1-2 to page 1-4.
•
•
Removed Table 1-1 on page 1-11.
Removed CdrDmpr.callDetail row
in Table 1-6 on page 1-11.
•
Removed Trigger Interface section
on page 1-18.
—
Initial release
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xxi
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
xxii
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
1
Billing Interfaces
This chapter describes the Cisco Media Gateway Controller (MGC) billing interface capabilities and its
call detail records (CDRs). This chapter is primarily a reference that contains the following sections:
•
•
Cisco MGC Billing Interfaces, page 1-19
Billing Capabilities Overview
The generic interface to the CDR dumper interface carries all the billing information in the form of call
detail blocks (CDBs). When the CDR dumper receives the CDB, it writes the record in the CDR file.
CDB generation is based on a point in call (PIC). The MGC predefines several PICs that can trigger the
generation of CDBs. Examples of PICs include Answered, Long Duration, and Released. For example,
the MGC triggers the generation of the Answered CDB when an Answer message (ANM for SS7) is
received.
Each CDB has a type associated with it that distinguishes the PIC.
CDB required events that are triggered are passed to the CDR manager module. When an event is
received, the action the CDR manager module takes is determined by its configuration. The CDR
manager module either handles or ignores the event.
System Interfaces
System interfaces vary according to the configuration. The configuration can be either dual MGC
(hot-standby) or standalone. The physical interface is described in the following section.
Physical Interface
The physical interface between the MGC and the mediation software (for example, Billing and
Measurements Server (BAMS)) relies on guaranteed delivery of the CDB information between both
MGCs. The interface consists of dual Ethernet links. Each link is physically isolated for redundancy.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Billing Capabilities Overview
RADIUS Interface
The RADIUS Enhancement for Accounting feature provides RADIUS interface support on the PGW
2200 for CDR data. For more information about the feature, including new CDRs, refer to the RADIUS
Enhancement for Accounting feature guide.
Message Interface
The CDB message interface is a one-way interface to the CDR dumper. The following paragraphs
describe the CDR message format for messages sent to the CDR dumper. The CDR dumper saves the
CDB message into the CDR files without any conversion or data manipulation.
CDBs are written to disk in a binary, tag-length-value (TLV) format. Many mediation systems depend
on input data that is preformatted in an ASCII format. An optional BAMS converts the MGC CDR billing
output files to ASCII.
The accuracy selection for timepoints is configurable on the MGC as seconds or milliseconds. In order
for the ASCII representation of timepoints to be properly displayed, a place holder for each type has been
provided in the ASCII output layout. For each timepoint type, two entries are contained in the output
format, one entry for seconds granularity and another entry for milliseconds granularity.
A downstream mediation or billing system (for example, BAMS) can easily parse these ASCII records.
Each record is prefixed in the ASCII file with a record identifier field, for example a 1110 record would
begin as follows: 1110,1234,5678,2222,...
The ASCII files are named with the same prefix name specified (refer to page 1-20 for a prefix example),
and postfixed with “.csv” rather than “.bin”. Each file resides in the /opt/CiscoMGC/var/bam directory.
Note
It is the system operator's responsibility to manage files created by the MGC billing process, including
archiving and deleting files from the system.
CDB Message Format
Each field within the CDB message has a tag, length, and value.
Figure 1-1 shows how the CDB record itself is also in TLV format with the value part composed of
multiple sub-TLVs. For performance reasons the first few fields(tags) of the value portion of the CDB
exists in a fixed order for every message. These fields are the Unique Call ID (tag 5000), CDB Version
(tag 4000), and CDB Timepoint (tag 4001).
Note
These three fields are fixed so that the CDR dumper can have direct access to these fields without having
As shown in Figure 1-1, the first tag in the CDB record identifies the CDB message type. The length
indicates the length of the entire message, excluding 4 bytes (2 bytes for the message tag and 2 bytes for
the length).
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Billing Capabilities Overview
Figure 1-1
CDB TLV Record Format
Tag Length Value
Tag
Length
Sub-TLV messages
The CDB message has both mandatory fields and optional fields. The following fields are mandatory in
each CDB message.
•
•
•
Unique Call ID
Version
CDB Timestamp
All other fields in the CDB message are considered optional. The optional fields do not appear in any
sort of predefined order. The TLV format allows the application to be insensitive to the order of the
message data. For example, in a 1010 Answer CDB message, the Call Reference ID tag (4002) could
appear as the first optional field, whereas in another CDB message, such as 1040 Release, the Call
Reference ID tag could appear as the last optional field.
Note
The mandatory fields exist in each CDB message, with their associated values and locations. The
optional fields can have no value. Optional fields with no value are not included in the CDB message, to
improve performance.
Tag Values
As shown in Figure 1-2, the tags are divided into categories. The first tag category is assigned to the CDB
message ID(s), the second category is assigned to CDB format fields, and the third category is assigned
to miscellaneous usage.
Each category is divided into two or more sections. One section is the MGC range, and another section
For example, in Figure 1-2, a Cisco MGC message ID range defined by a customer (1900 through 1999)
can be used for generating customer-specific CDB auditing records. The auditing records can be for
beginning and ending the CDR file. The field tag range can also use the customer-defined range for the
field category (5900 through 5999) to define new fields in the CDB auditing records.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Billing Capabilities Overview
Figure 1-2
CDB Tag Categories
1000
MGC message IDs
CDB message ID tag category
1900
1999
Customer defined
MGC ANSI format
2999
3999
4999
MGC ITU format
MGC generic format
Reserved
CDB fields tag category
5900
5999
Customer defined
MGC miscellaneous
6999
Reserved
Miscellaneous tag category
7900
7999
Customer defined
Formats and Codes
The CDB message tag and the length fields are binary encoded using big-endian (BE). The tag field
holds the value to identify the CDB field, and the length field holds the number of octets (length) of the
CDB field.
Note
The length indicator value does not include the field tag octets (2 octets) or the length indicator octets
(2 octets).
The CDB field value is encoded as specified BE, International Alphabet No. 5 (IA5), ANSI T1.113, or
ITU Q.763).
CDB Record Types
This section describes different types of CDBs and their relation to PIC events. Creation of the CDB is
based on certain PIC events (refer to Table 1-1), and other call events.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Billing Capabilities Overview
Table 1-1
CDB Types
CDB Tag
Value
Point in Call Event
Description
CDB Message/Record
Answer call event
Call went through and was answered.
Circuit cannot be used, passed to another.
1010
1020
Set CDB record
Deselected outgoing
circuit event
Deselected outgoing circuit
CDB record
Aborted attempt call event Call did not get to setup status.
1030
1040
1050
1060
1070
Aborted attempt CDB record
Release CDB record
Release call event
Interrupted call event
On-going call event
Released call.
Call terminating without release message.
Long call.
Interrupted CDB record
On-going call CDB record
Maintenance CDB record
SS7 CIC Audit CDB record
Maintenance CDB record Circuit maintenance.
N/A
Sent as a result of a Cisco MGC audit or a change in 1071
circuit counts via the sta-aud-cic MML command.
External access CDB
File header CDB
File footer CDB
End of a call CDB
Call sent a query to a Service Control Point (SCP) (or 1080
to another external device or database).
External access CDB record
File header CDB record
File footer CDB record
End of a Call CDB
CDR dumper creates the file header CDB at the
beginning of each CDR file.
1090
CDR dumper creates the file footer CDB at the end of 1100
each CDR file.
This CDB is generated when the MGC is configured 1110
to have one CDB per call.
It is generated at the end of the call (as in Release
CDB) or when the call did not get to setup status (as
in Aborted attempt CDB).
Note
If the Cisco MGC is configured for 1110
output, the 1010, 1030, and 1040 CDBs must
not be configured for inclusion in the output
billing files.
Half call slave release
event CDB
Refer to the 1110 CDB definition and apply to a
non-controlling slave half call instance.
1210
1260
Slave End of a Call CDB
Half call slave ongoing
call event CDB
Refer to th 1060 CDB definition and apply to a
non-controlling slave half call instance.
Slave Long Duration Call
CDB
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Block Descriptions
Call Data Block Descriptions
The CDB consists of several call data elements (CDEs) that are related to a certain point in call (PIC).
Each CDE has a tag, a length, and a value. Table 1-2 defines the CDE fields in a CDB.
Table 1-2
CDB Call Data Element Fields for Current Release
CDE Tag Numbers
Millisecond
Granularity
Miscellaneous/
Protocol Specific
CDB Name
CDB Tag
Common
ANSI
ITU
Answered
1010
4000–4005, 4008–4016, 4029, 4100–4105
4034–4043, 4048, 4060, 4063,
4066–4073, 4080, 4081,
2000, 2001,
2003–2007,
2009–2020
3000, 3001, 6100–6104
3003,
3005–3007,
4083–4086, 4089, 4090,
3009–3013,
4092–4096, 4201–4207,
3017–3020
4209–4212, 4236, 4237,
4240–4243, 5000
Deselected
Aborted
1020
1030
4000–4003, 4006, 4008, 4009, 4100, 4101,
4015, 4016, 4019, 4020, 4028, 4106, 4108,
4034–4037, 4081, 4232, 4233, 4109
5000
2008–2012
3008–3012 6100–6104
4000–4004, 4006, 4008–4016, 4100–4103,
2000, 2001,
2003–2009,
2011–2020
3000, 3001, 6100–6104
3003,
3005–3009,
3011, 3013,
3017–3020
4019, 4020, 4028, 4029,
4034–4039, 4046–4048,
4060–4062, 4065–4073,
4078–4080, 4082–4096, 4098,
4099, 4201–4212, 4232, 4233,
4236, 4237, 4239, 4240–4245,
4246, 5000
4106–4109,
Release
1040
4000–4002, 4006, 4019, 4020, 4106–4109,
4028, 4030, 4044, 4046, 4047,
4061, 4062, 4078, 4079,
4082–4091, 4095–4099,
4205–4210, 4213, 4214,
4227–4231, 4239, 4240, 4241,
5000
2008
3008
Interrupted
Ongoing
1050
1060
4000–4002, 4007, 4081, 5000
4000–4005, 4008–4010, 4012, 4100–4105,
4014–4016, 4066–4073, 4080,
2018–2020
3017–3020
4081, 4213, 4214, 4237, 5000
Maintenance
1070
4000–4002, 4017, 4018, 4032,
4074–4077, 4081, 5000
SS7 CIC Audit 1071
4000–4002, 4017, 4074, 4081,
5000
External DB
1080
1090
4000–4002, 4040– 4043, 4234,
4235, 5000
File Header
CDB
4000–4002
6000, 6001,
6004
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Block Descriptions
Table 1-2
CDB Call Data Element Fields for Current Release (continued)
CDE Tag Numbers
Millisecond
Granularity
Miscellaneous/
Protocol Specific
CDB Name
CDB Tag
Common
ANSI
ITU
File Footer
CDB
1100
4000–4002
6000, 6002,
6003, 6004
End of Call
1110
4000–4002, 4008–4012,
4014–4016, 4028, 4034–4037,
4046, 4047, 4060–4063, 4065,
4068, 4072, 4078–4080,
4082–4099, 4201–4212, 4213,
4214, 4227–4231, 4232, 4233,
4236, 4237, 4239, 4240–4245,
4246, 5000
4100–4109,
2000–2005,
2007, 2008,
2013, 2015,
2017–2020
3000, 3001,
3003, 3005,
3007, 3008,
3017–3020
Slave End of
Call
1210
1260
4002, 4003, 4006, 4008, 4009,
4015, 4016, 4227, 4228, 5000
Slave Long
Duration Call
4002, 4003, 4006, 4008, 4009,
4015, 4016, 4227, 4228, 5000
Enabling Call Screening
To initialize the database that stores call screening information, modify the SysConnectDataAccess
parameter in the Engine section of the XECfgParm.dat file: For parameter modification, enter
SysConnectDataAccess.
Note
Making changes to the XECfgParm.dat file requires the system software to be stopped, the parameter
value changed, and the software restarted. Contact Cisco TAC before stopping the system software.
To enable or disable the A-number and B-number analysis in the call screening database, enter one of
the following values:
•
If you do not have the database environment set with all the required data populated, set this value
to false (default).
•
If you have the database and want the system to access it, set this value to true.
Configuring Call Detail Record File Output
To configure the CDR file output, modify the following parameters in the Data Dumper and Engine
sections of the XECfgParm.dat file:
Parameter modification: engine.CDRencodingFormat
To specify the CDR file encoding format, enter one of the following values:
•
•
AnsiCDB-North American (default)
ItuCDB-European
Parameter modification: engine.CDRtimeStamp
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Block Descriptions
To specify the CDR file timestamp unit, enter one of the following values:
•
•
S-Seconds (default).
M-Milliseconds; use this parameter if your configuration uses TCAP.
Note
Note
If you use 1110 in the engine.CDRmessageTypes parameter (for TCAP), you must specify milliseconds
for the CDRtimeStamp value.
The timestamp value is in Coordinated Universal Time (UTC). Previously the term used was Greenwich
Mean Time (GMT).
Configuring Call Detail Record Message Types
Parameter modification: engine.CDRmessageTypes
To specify which CDBs (statistics taken at various points in a call) are recorded during a call, enter one
of the two following sets of values (each number represents a point in a call):
•
1010, 1020, 1030, 1040, 1050, 1060, 1070, 1080—Use this set of values if your CDR files are used
by a measurement server or by another CDR reader.
•
•
1060, 1110—Use this set of values if the end-of-call record is desired.
1071—Use this set of values for BAMS measurements.
To initialize the database that stores call screening information, modify the parameters shown in
Table 1-3.
Table 1-3
Parameter
Call Screening Parameters
Modification
engine.SysConnectDataAccess
To enable or disable the A-number and B-number analysis in
the call screening database, enter one of the following values:
•
If you do not have the database environment set with all
the required data populated, set this value to false
(default).
•
If you have the database and want the system to access it,
set this value to true.
Configuring Call Detail Record File Output
To configure the CDR file output, modify the parameters shown in Table 1-4 in the Data Dumper and
Engine sections of the XECfgParm.dat file:
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-4
Call Detail Record File Output Parameters
Parameter
Modification
engine.CDRencodingFormat
To specify the call detail record (CDR) file encoding format,
enter one of the following values:
•
•
AnsiCDB—North American (default)
ItuCDB—European
engine.CDRmessageTypes
To specify which call detail blocks (CDBs, statistics taken at
various points in a call) are recorded during a call, enter one
of the two following sets of values (each number represents a
point in a call):
•
1010, 1020, 1030, 1040, 1050, 1060, 1070, 1080—Use
this set of values if your CDR files are to be read by a
measurement server or other CDR reader.
•
•
1060, 1110—Use this set of values if the end-of-call
record is desired.
1071—Use this set of values for BAMS measurements.
engine.CDRtimeStamp
To specify the CDR file time-stamp unit, enter one of the
following values:
•
•
S—Seconds (default).
M—Milliseconds; use this parameter if your
configuration uses TCAP or BAMS.
Note
If you use are using BAMS or 1110 in the
engine.CDRmessageTypes parameter (for TCAP),
you must specify milliseconds (M) for the
CDRtimeStamp value.
cdrDmpr.openCDR
To indicate whether the standard data dumper writes out CDR
files, enter one of the following values:
•
true—Standard data dumper opens a CDR file and logs
call detail blocks (CDBs).
•
false—Standard data dumper does not open a CDR file
and does not log CDBs.
cdrDmpr.seqFile
Indicate the location of the file for storing or retrieving the
CDR sequence number (range is 1 to 999999).
Default: ../var/.cdr.seq
Call Data Element Descriptions
This section describes the current CDB CDEs. The CDEs are divided into three tables (ANSI, ITU, and
generic format).
The ANSI formatted fields are used for customers requesting ANSI-formatted fields (as is the case for
North American customers) and is based on ANSI T1.113.1995.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
The ITU formatted fields are used for customers requesting ITU-formatted-fields (as is the case for
European customers) and is based on ITU-Q.763.
The generic format provides common CDEs with one encoding scheme. The generic format is used to
handle different protocol variants.
Table 1-5 defines all the fields that can exist in any given CDB along with the associated tag and type
for each one.
Table 1-5
CDE Detail Description for the Current Release
Ans-
De-
Inter-
On-
Maint-
External End of 1071
Call 1210
(1110) 1260
Tag wered selected Aborted Release rupted going enance DB
Value (1010) (1020)
Field Name
(1030)
(1040)
(1050) (1060) (1070)
(1080)
ANSI Based Formatted Fields
Calling Party
Category
2000
2001
2002
2003
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
Y
Y
Y
N
Y
N
N
N
N
N
N
N
N
User Service
Information
Originating Line
Information
Calling Number
Nature of Address
Charged Number 2004
Nature of Address
Dialed Number
Nature of Address
2005
2006
2007
LRN Nature of
Address
Called Number
Nature of Address
Reason Code
2008
2009
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
Y
N
N
N
Forward Call
Indicators
Received
Forward Call
Indicators Sent
2010
2011
Y
Y
Y
Y
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Nature of
Connection
Indicators
Received
Nature of
Connection
Indicators Sent
2012
2013
Y
Y
Y
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
Transit Network
Selection
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
Carrier
2014
Y
N
Y
N
N
N
N
N
N
N
Identification
Parameter
Carrier Selection
Parameter
2015
2016
Y
Y
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
Jurisdiction
Information
Parameter
Redirecting
Number NOA
2017
2018
Y
Y
Y
Y
N
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
Egress Calling
Number NOA
Egress Redirecting 2019
Number NOA
Egress Original
Called Number
NOA
2020
ITU Based Formatted Fields
Calling Party
Category
3000
3001
3003
3005
3006
3007
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
Y
N
N
N
N
N
N
User Service
Information
Calling Number
Nature of Address
Dialed Number
Nature of Address
LRN Nature of
Address
Called Number
Nature of Address
Reason Code
3008
3009
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
Y
N
N
N
Forward Call
Indicators
Received
Forward Call
Indicators Sent
3010
3011
Y
Y
Y
Y
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Nature of
Connection
Indicators
Received
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
Nature of
3012
Y
Y
N
N
N
N
N
N
N
N
Connection
Indicators Sent
Transit Network
Selection
3013
3017
3018
Y
Y
Y
Y
Y
N
N
N
N
N
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
N
Redirecting
Number NOA
Egress Calling
Number NOA
Egress Redirecting 3019
Number NOA
Egress Original
Called Number
NOA
3020
MGC Generic Tags
CDB Version
4000
4001
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
1071
1071
CDB Timepoint
Call Reference ID 4002
1210
1260
IAM Timepoint
4003
Y
Y
Y
N
N
Y
N
N
N
1210
1260
ACM Timepoint
ANM Timepoint
REL Timepoint
Crash Timepoint
4004
4005
4006
4007
Y
Y
N
N
Y
N
N
Y
N
Y
Y
N
Y
N
Y
N
N
Y
N
N
N
N
N
Y
N
Y
Y
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
1210
N
Originating Trunk 4008
Group
1210
1260
Originating
Member
4009
Y
Y
Y
N
N
Y
N
N
Y
1210
1260
Calling Number
Charged Number
Dialed Number
LRN Number
4010
4011
4012
4013
4014
Y
Y
Y
Y
Y
Y
N
N
N
N
N
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
Y
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
Y
Y
N
N
N
N
N
Called Number
Terminating Trunk 4015
Group
1210
1260
Terminating
Member
4016
Y
Y
Y
N
N
Y
N
N
Y
1210
1260
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
Maint Trunk Group 4017
N
N
N
N
N
N
Y
N
N
1071
Maint Circuit
Member
4018
N
N
N
N
N
N
Y
N
N
N
Glare Encountered 4019
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
RLC Release
Timepoint
4020
4028
4029
First Release
Source
N
Y
Y
Y
N
N
N
N
Y
N
LNP Dip
Y
N
N
N
N
N
N
N
Y
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Total Meter Pulses 4030
Maint Type
4032
4033
Maint Reason
(Retired in Release
9.4(1))
Ingress
Originating Point
Code
4034
4035
4036
4037
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y (9.3
and
up)
N
N
N
N
Ingress
Destination Point
Code
Y (9.3
and
up)
Egress
Originating Point
Code
Y (9.3
and
up)
Egress
Destination Point
Code
Y (9.3
and
up)
Ingress Media
Gateway ID
4038
4039
4040
Y
Y
Y
Y
Y
N
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
Egress Media
Gateway ID
TCAP
Transaction
Identification
Transaction Start
Time
4041
4042
4043
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
Transaction End
Time
TCAP Database
Identification
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
Announcement
Identification
4044
4046
4047
4048
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
Ingress Gateway
Packet Info
Y
Y
Y
Y
N
N
Egress Gateway
Packet Info
Directional Flag
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
N
N
N
N
Service Logic ID 4049
AMA Line
Number
4050
Originating
Gateway
Primary Select
4052
N
N
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
Terminating
Gateway
Primary Select
4053
4060
Redirecting
Number
Tariff Rate
4061
4062
N
N
Y
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
Scale Factor
Test Line Indicator 4063
Redirection
Number
4065
Ingress SigPath ID 4066
Ingress Span ID 4067
Y
Y
Y
N
N
N
Y
Y
Y
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
Ingress BearChan 4068
ID
Y (9.3
and
up)
Ingress Protocol
ID
4069
Y
N
Y
N
N
Y
N
N
N
N
Egress SigPath ID 4070
Egress Span ID 4071
Y
Y
Y
N
N
N
Y
Y
Y
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
Egress BearChan 4072
ID
Y (9.3
and
up)
Egress Protocol ID 4073
Y
N
N
N
Y
N
N
N
N
N
Y
N
N
Y
N
N
N
N
N
Maintenance
SigPath ID
4074
1071
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
Maintenance Span 4075
ID
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
Maintenance
BearChan ID
4076
4077
4078
N
N
Y
Y
Y
N
N
Y
Y
N
N
N
N
N
N
Maintenance
Circuits Count
Charge Band
Number
Furnish Charging 4079
Information
Original Called
Number
4080
T.38 Fax Call
4081
4082
Y
N
Y
N
N
Y
N
Y
Y
N
Y
N
Y
N
Y
N
N
Y
N
N
Charge Unit
Number
Charge Indicator
4083
Y
Y
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
N
N
Outgoing Calling 4084
Party Number
MCID Request
Indicator
4085
4086
4087
Y
Y
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
MCID Response
Indicator
Ingress MGCP
DLCX Return
Code
Egress MGCP
DLCX Return
Code
4088
4089
N
Y
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
N
N
Network
Translated
Address Indicator
Reservation
Request Accepted
4090
4091
Y
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
N
N
Reservation
Request Error
Count
ATM Ingress
Configured Profile
4092
4093
Y
Y
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
ATM Egress
Configured Profile
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
ATM Negotiated
Profiler
4094
Y
N
Y
N
N
N
N
N
Y
N
Route List Name
Route Name
4095
4096
4097
Y
Y
N
N
N
N
Y
Y
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
MGCP Script
Response String
Originating Leg
DSP statistics (9.4
and up)
4098
4099
4201
N
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
N
N
Terminating Leg
DSP statistics (9.4
and up)
Originating
Remote SIP Host
Y
Y
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
Originating Local 4202
SIP Host
SIP Call ID
4203
Y
Y
Y
N
N
N
Y
Y
Y
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
Source IP Address 4204
Ingress Media
Device Address
4205
4206
Egress Media
Y
N
Y
Y
N
N
N
N
Y
N
Device Address
Initial Codec
Final Codec
4207
4208
4209
Y
N
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
Ingress Media
Device Port
Egress Media
Device Port
4210
4211
Y
Y
Y
N
N
N
N
N
Y
Y
Y
N
Y
N
N
Y
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
Originating VPN
ID
Terminating VPN 4212
ID
Meter Pulses
Received
4213
Meter Pulses Sent 4214
Charge Tariff Info 4215
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
Y
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
Advice of Charge 4216
Indicator
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
Short Call
Indicator
4217
4218
4219
4220
N
N
N
Y
N
N
N
N
N
Y
N
N
N
N
N
N
N
Y
N
N
N
N
N
Y
Y
Y
Y
N
N
N
N
Charge Limit
Exceeded
N
N
Y
Y
Y
N
N
N
N
Call Recovered
Indication
Partial Calling
Line Identity
Service Activation 4221
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
Y
Y
N
N
PRI AOC Invoke
Type
4222
PRI AOC – S
Charge
Information
4223
N
N
N
N
N
N
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
N
PRI AOC – D
Charge
Information
4224
4225
PRI AOC – E
Charge
Information
PRI AOC Invoke
Failure
4226
4227
N
N
N
N
N
N
N
N
Y
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
RO/PR Executed
(added in 9.6)
1210
1260
RO/PR Other Call 4228
Ref (added 9.6)
1210
1260
RO/PR Trunk
Group Info
4229
N
(added in 9.6)
RO/PR
4230
N
N
N
Y
N
N
N
N
Y
N
Replacement Chan
ID
(added in 9.6)
RO Switchover
Timestamp
(added in 9.6)
4231
N
N
N
Y
N
Y
Y
N
N
N
N
N
N
N
N
N
Y
Y
N
N
RejectingLocation 4232
Label
(added in 9.6(1))
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Call Data Element Descriptions
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
RejectingLocation 4233
Label Direction
(added in 9.6(1))
N
N
N
Y
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
Y
N
N
N
PRI AOC – E
Charge
Information
4234
4235
N
N
Y
Y
N
N
1071
1071
PRI AOC Invoke
Failure
H323 Destination 4236
Y
Y
N
N
Y
Y
N
N
N
N
N
Y
N
N
N
N
Y
Y
Ingress
4237
N
N
Redirecting
Number
Service Usage
Data
4239
N
N
Y
Y
N
N
N
N
Y
CNAM DIP
4240
4241
4242
Y
Y
Y
N
N
N
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
Calling Name
Terminating
Remote SIP Host
Terminating Local 4243
SIP Host
Y
N
N
N
N
N
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
N
N
N
License Rejecting 4244
Reason
License Rejecting 4245
Direction
SIP Transport
4246
Y
Y
N
N
Y
Y
N
N
N
N
N
N
N
N
N
N
Y
Y
N
N
SIP Routing URI 4247
Source
SIP Routing URI 4248
Y
N
Y
N
N
N
N
N
Y
N
Millisecond Granularity Timepoint Fields
IAM Timepoint
Received_ms
4100
4101
4102
4103
4104
Y
Y
Y
Y
Y
Y
Y
N
N
N
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
N
N
N
N
N
IAM Timepoint
Sent_ms
ACM Timepoint
Received_ms
ACM Timepoint
Sent_ms
ANM Timepoint
Received_ms
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Cisco MGC Billing Interfaces
Table 1-5
CDE Detail Description for the Current Release (continued)
Ans- De- Inter-
On-
Maint-
External End of 1071
Tag
wered selected Aborted Release rupted going enance DB
Call
1210
Field Name
Value (1010) (1020)
(1030)
(1040)
(1050) (1060) (1070)
(1080)
(1110) 1260
ANM Timepoint
Sent_ms
4105
4106
4107
4108
4109
Y
N
N
N
N
N
Y
N
Y
Y
N
N
N
N
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
Y
Y
Y
Y
Y
N
N
N
N
N
First REL
Timepoint_ms
Y
Y
Y
Y
Y
Y
Y
Y
N
N
N
N
Second REL
Timepoint_ms
RLC Timepoint
Received_ms
RLC Timepoint
Sent_ms
Cisco Reserved Tags
Unique Call Corre- 5000
lator ID (Release 9
and later)
Y
Y
Y
Y
Y
Y
Y
Y
Y
1071
1210
1260
Miscellaneous Fields
This field is used only in the File Header CDB and File Footer CDB. These CDBs are not
optional and are generated by the CDR dumper for each CDR file.
MGC ID
6000
6001
6002
6003
File Start Time
File End Time
Total Number of
CDB records
MGC Version
Interim CDB
6004
6005
N
N
N
Y
N
N
N
N
Y
N
Protocol Specific Fields
TTC Contract #
6100
6101
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
TTC Contract #
NOA
TTC Charge Info 6102
Y
Y
Y
Y
Y
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
TTC Charge Info 6103
Type
TTC Charge Area 6104
Info
Y
Y
Y
N
N
N
N
N
N
N
Cisco MGC Billing Interfaces
There are two billing interfaces provided by the Cisco MGC. They are:
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Redundant Cisco MGC Configuration
•
•
File Transfer Protocol (FTP) interface
Generic interface
FTP Interface
The FTP interface allows the user to FTP the CDR files from the spool directory. This interface supports
users who own a mediation system or data collocation system. Users can process the CDR files on a
separate system.
The Cisco MGC runs on Solaris UNIX that provides the standard file transfer capability (FTP). The
Cisco MGC can be configured so other systems can download the CDR files from the spool directory.
The FTP download can be restricted by establishing user privileges.
The data collector and mediation systems can use this interface by periodically downloading the files.
The CDR files provide a sequence number and the timestamp of the file creation. The data collection
system or the mediation system can use this information to determine the desired file to download.
The Cisco MGC has several configuration parameters to write the CDR file. The following are the
configuration parameters:
•
The prefix in the file name (CDR_YYYYMMDDHHMMSS_SeqNo) where SeqNo is in the format
(000001 to 999999)
•
•
Spool directory
Frequent creation of the file
The sequence number provides an audit capability to the data collection system or mediation software.
The sequence number is unique and ranges from 1 to 999999. If the system fails or restarts, it uses the
next sequence number (last sequence number + 1). When the sequence number reaches 999999, it then
restarts at 1.
Generic Interface
The Cisco MGC defines a generic or flexible billing interface. This is an internal interface between the
call processing module and the CDR dumper in Cisco MGC. Users cannot modify this interface.
This interface provides a CDB data stream for the CDR dumper. The generic interface is based on the
flexible CDB record layout. The record layout uses a tag, length, and value (TLV) encoding mechanism.
The detail messages (that is, CDBs) are explained later in this document.
Redundant Cisco MGC Configuration
In a redundant Cisco MGC configuration, the active Cisco MGC creates checkpoint records to
synchronize it with the standby Cisco MGC. The standby Cisco MGC creates call objects with
appropriate states to allow continued call processing after switchover occurs. When the standby Cisco
MGC becomes active, it starts synchronizing with End Offices (circuit audit). Another aspect of the
architecture is that the Cisco 2600s buffer messages while failover occurs.
Billing under a redundant configuration is basically limited to the following: The active Cisco MGC
generates the CDBs and the standby Cisco MGC does not. When failover occurs, the now active
Cisco MGC generates the CDBs.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Cisco MGC Clock Synchronization
If a call was stable during the failover, then the newly active Cisco MGC eventually generates an end of
a call CDB (Release CDB or possibly an Interrupted CDB) for each call. The CDBs generated by the
previous standby MGC include the same unique Call IDs. The mediation software requires correlating
the CDB records from both systems. For both systems to be properly correlated, both Cisco MGC clocks
must be synchronized with each other.
Cisco MGC Clock Synchronization
The Cisco MGC uses Network Time Protocol (NTP) to synchronize its time to another server or
reference time source, such as a radio or satellite receiver or modem. For example, the NTP provides
client accuracy that is typically within 1 millisecond on LANs and up to a few tenths of a second on
WANs relative to a primary server synchronized to Coordinated Universal Time (UTC) by a Global
Positioning Service (GPS) receiver. To achieve high accuracy and reliability, typical NTP configurations
use multiple redundant servers and diverse network paths. Some configurations include cryptographic
authentication to prevent accidents or malicious protocol attacks.
Note
RFC-1305 provides information on the NTP architecture, protocol, and algorithm.
Detailed CDB Description
This section contains the distinct record layouts for the CDB. Since each type of CDB is for a different
part of a call, the Cisco MGC provides the related CDEs that are needed.
Note
The CDE includes only fields that have values. The layout varies based on the Cisco MGC configuration.
For example, if the Cisco MGC is configured with a protocol that does not support a specific CDE, then
the CDB record does not include that particular CDE.
Answered CDB Record (Tag: 1010/Release 5 or Later)
Table 1-6 lists data about the answered message. This CDB is generated when a call went through and
was answered (when the Cisco MGC receives ANM/Answered message).
Table 1-6
Answered CDB Record
Tag
Field Name
Value Comments
When configured for ANSI-based formatted
fields (Release 7 or later option)
ANSI Based Formatted Fields
Calling Party Category
2000
2001
2002
2003
2004
User Service Information
Originating Line Information
Calling Number Nature of Address
Charged Number Nature of Address
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-6
Answered CDB Record (continued)
Tag
Field Name
Value Comments
Dialed Number Nature of Address
LRN Nature of Address
2005
2006
2007
2009
2010
2011
Called Number Nature of Address
Forward Call Indicators Received
Forward Call Indicators Sent
Nature of Connection Indicators
Received
Nature of Connection Indicators Sent
Transit Network Selection
2012
2013
2014
2015
2016
2017
2018
2019
2020
Carrier Identification Parameter
Carrier Selection Parameter
Jurisdiction Information Parameter
Redirecting Number NOA
Egress Calling Number NOA
Egress Redirecting Number NOA
Egress Original Called Number NOA
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
When configured for ITU-based formatted
fields (Release 7 or later option)
ITU Based Formatted Fields
Calling Party Category
3000
3001
3002
3003
3005
3006
3007
3009
3010
3011
User Service Information
Originating Line Information
Calling Number Nature of Address
Dialed Number Nature of Address
LRN Nature of Address
Called Number Nature of Address
Forward Call Indicators Received
Forward Call Indicators Sent
Nature of Connection Indicators
Received
Nature of Connection Indicators Sent
Transit Network Selection
3012
3013
3017
3018
3019
3020
Redirecting Number NOA
Egress Calling Number NOA
Egress Redirecting Number NOA
Egress Original Called Number NOA
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-6
Answered CDB Record (continued)
Tag
Field Name
Value Comments
MGC Generic Tags
CDB Versionb
4000
4001
4002
CDB Timepoint
Call Reference ID
IAM Timepoint
4003
4004
4005
When configured for seconds timepoint
(Release 7 or later option)
ACM Timepoint
ANM Timepoint
When configured for seconds timepoint
(Release 7 or later option)
When configured for seconds timepoint
(Release 7 or later option)
Originating Trunk Group
Originating Member
Calling Number
4008
4009
4010
4011
4012
4013
4014
4015
4016
4029
4031
4034
4035
4036
4037
4038
4039
4040
4041
4042
4043
4045
4048
4060
4063
Charged Number
Dialed Number
LRN Number
Called Number
Terminating Trunk Group
Terminating Member
LNP Dip
MGC Info Field
Disabled as of Release 7.3.x, 7.4.x
Ingress Originating Point Code
Ingress Destination Point Code
Egress Originating Point Code
Egress Destination Point Code
Ingress Media Gateway (CU)
Egress Media Gateway (CU)
TCAP Transaction Identification
Transaction Start Time
Transaction End Time
TCAP Database Identification
Route Selection Info
Directional Flag
Ingress Media Gateway ID
Egress Media Gateway ID
Redirecting Number
Number or address from which forwarded
Test Line Indicator
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-6
Answered CDB Record (continued)
Tag
Field Name
Value Comments
Ingress SigPath ID
Ingress Span ID
4066
4067
4068
4069
4070
4071
4072
4073
4080
4083
4084
4085
4086
Ingress BearChan ID
Ingress ProtocolId
Egress SigPath ID
Egress Span ID
Egress BearChan ID
Egress ProtocolId
Original Called Number
Charge Indicator
Release 9.3(1) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Outgoing Calling Party Number
MCID Request Indicator
MCID Response Indicator
Network Translated Address Indicator 4089
Reservation Request Accepted
Reservation Request Error Count
ATM Ingress Configured Profile
ATM Egress Configured Profile
ATM Negotiated Profile
4090
4091
4092
4093
4094
4095
4096
4097
4201
Route List Name
Route Name
MGCP Script Response String
Originating Remote SIP Host
Release 9 and later (Named as Ingress SIP URL
in versions prior to the Release 9.7(3))
Originating Local SIP Host
4202
Release 9 and later (Named as Egress SIP URL
in versions prior to the Release 9.7(3))
SIP Call ID
4203
4204
4205
4206
4207
4209
4210
4211
4212
4220
Release 9 and later
Source IP Address
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.5(2) and later
Ingress Media Device Address
Egress Media Device Address
Initial Codec
Ingress Media Device Port
Egress Media Device Port
Originating VPN ID
Terminating VPN ID
Partial Calling Line Identity
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-6
Answered CDB Record (continued)
Tag
Field Name
Value Comments
H323 Destination
4236
4237
4240
4241
4242
4243
4246
4247
4248
Release 9.7 and later
Ingress Redirecting Number
CNAM DIP
Added in a Release 9.5(2) patch
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Calling Name
Terminating Remote SIP Host
Terminating Local SIP Host
SIP Transport
SIP Routing URI Source
SIP Routing URI
Millisecond Granularity Timepoint Fields
IAM Timepoint Received_ms
IAM Timepoint Sent_ms
ACM Timepoint Received_ms
ACM Timepoint Sent_ms
ANM Timepoint Received_ms
ANM Timepoint Sent_ms
4100
4101
4102
4103
4104
4105
Cisco Reserved Tags
Unique Call ID (Release 9 and later)
5000
Deselected Outgoing Circuit CDB Record (Tag: 1020/Release 5 or Later)
Table 1-7 lists data about the deselected outgoing circuit. CDB Tag 1020 is generated when a circuit is
attempted to be used and for some reason the circuit can not be used. The call is then passed to another
circuit to complete the call.
Table 1-7
Deselected Outgoing Circuit CDB Record
Tag
Field Name
Value Comments
When configured for ANSI encoding (Release 7
or later)
ANSI Based Formatted Fields
Reason Code
2008
2009
2010
2011
Forward Call Indicators Received
Forward Call Indicators Sent
Nature of Connection Indicators
Received
Nature of Connection Indicators Sent 2012
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-7
Deselected Outgoing Circuit CDB Record (continued)
Tag
Field Name
Value Comments
When configured for ITU encoding (Release 7 or
later)
ITU Based Formatted Fields
Reason Code
3008
3009
3010
3011
Forward Call Indicators Received
Forward Call Indicators Sent
Nature of Connection Indicators
Received
Nature of Connection Indicators Sent 3012
MGC Generic Tags
CDB Version
4000
4001
4002
4003
4006
4008
4009
4015
4016
4019
4020
4028
4034
4035
4036
4037
4038
4039
4232
CDB Timepoint
Call Reference ID
IAM Timepoint
When timepoint in seconds is selected
When timepoint in seconds is selected
REL Timepoint
Originating Trunk Group
Originating Member
Terminating Trunk Group
Terminating Member
Glare Encountered
RLC Timepoint
First Release Source
Ingress Originating Point Code
Ingress Destination Point Code
Egress Originating Point Code
Egress Destination Point Code
Ingress Media Gateway (CU)
Egress Media Gateway (CU)
Rejecting Location Label
Release 9.6(1) and later
Release 9.6(1) and later
Rejecting Location Label Direction 4233
When configured for milliseconds (Release 7 or
later)
Millisecond Granularity Timepoint Fields
IAM Timepoint Received_ms
IAM Timepoint Sent_ms
First REL Timepoint_ms
RLC Timepoint Received_ms
4100
4101
4106
4108
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-7
Deselected Outgoing Circuit CDB Record (continued)
Tag
Field Name
Value Comments
RLC Timepoint Sent_ms
4109
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
Aborted Attempt CDB Record (Tag: 1030/Release 5 or Later)
Table 1-8 lists data about the aborted attempt. CDB Tag 1030 is generated for an attempted call that did
not get to Setup status. That is a call that did not get answered.
Table 1-8
Aborted Attempt CDB Record
Tag
Field Name
Value Comments
When configured for ANSI based encoding
ANSI Based Formatted Fields
Calling Party Category
(Release 7 or later)
2000
2001
2002
2003
User Service Information
Originating Line Information
Calling Number Nature of Address
Charged Number Nature of Address 2004
Dialed Number Nature of Address
LRN Nature of Address
2005
2006
2007
2008
2009
2011
Called Number Nature of Address
Reason Code
Forward Call Indicators Received
Nature of Connection Indicators
Received
Nature of Connection Indicators Sent 2012
Transit Network Selection
2013
2014
2015
2016
2017
2018
2019
Carrier Identification Parameter
Carrier Selection Parameter
Jurisdiction Information Parameter
Redirecting Number NOA
Egress Calling Number NOA
Egress Redirecting Number NOA
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Egress Original Called Number NOA 2020
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-8
Aborted Attempt CDB Record (continued)
Tag
Field Name
Value Comments
When configured for ITU encoding (Release 7 or
later)
ITU Based Formatted Fields
Calling Party Category
3000
3001
3002
3003
3005
3006
3007
3008
3009
3011
User Service Information
Originating Line Information
Calling Number Nature of Address
Dialed Number Nature of Address
LRN Nature of Address
Called Number Nature of Address
Reason Code
Forward Call Indicators Received
Nature of Connection Indicators
Received
Transit Network Selection
Redirecting Number NOA
Egress Calling Number NOA
Egress Redirecting Number NOA
3013
3017
3018
3019
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Added in a Release 9.5(2) patch
Egress Original Called Number NOA 3020
MGC Generic Tags
CDB Version
4000
4001
4002
4003
4004
4006
4008
4009
4010
4011
4012
4013
4014
4015
4016
4019
CDB Timepoint
Call Reference ID
IAM Timepoint
When configured for seconds timepoint
When configured for seconds timepoint
When configured for seconds timepoint
ACM Timepoint
REL Timepoint
Originating Trunk Group
Originating Member
Calling Number
Charged Number
Dialed Number
LRN Number
Called Number
Terminating Trunk Group
Terminating Member
Glare Encountered
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-28
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-8
Aborted Attempt CDB Record (continued)
Tag
Field Name
Value Comments
RLC Timepoint
4020
4028
4029
4031
4034
4035
4036
4037
4038
4039
4046
4047
4048
4060
4061
4062
4063
4065
4066
4067
4068
4069
4070
4071
4072
4073
4078
4079
4080
4081
4082
4083
4084
4085
4086
When timepoint in seconds is selected
First Release Source
LNP Dip
MGC Info Field
Disabled as of Release 7.3.x and 7.4.x
Ingress Originating Point Code
Ingress Destination Point Code
Egress Originating Point Code
Egress Destination Point Code
Ingress Media Gateway (CU)
Egress Media Gateway (CU)
Ingress Gateway Packet Info
Egress Gateway Packet Info
Directional Flag
Restored as of Release 9.4(1)
Restored as of Release 9.4(1)
Redirecting Number
Tariff Rate
Scale Factor
Test Line Indicator
Redirection Number
Ingress SigPath ID
Release 9.7(3) and later
Ingress Span ID
Ingress BearChan ID
Ingress ProtocolId
Egress SigPath ID
Egress Span ID
Egress BearChan ID
Egress ProtocolId
Charge Band Number
Furnish Charging Information
Original Called Number
T.38 Fax Call
Release 9.3(1) and later
Release 9.3(1) and later
Release 9.3(1) and later
Release 9.3(2) and later
Release 9.3(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Charge Unit Number
Charge Indicator
Outgoing Calling Party Number
MCID Request Indicator
MCID Response Indicator
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-8
Aborted Attempt CDB Record (continued)
Tag
Field Name
Value Comments
Ingress MGCP DLCX Return Code 4087
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Egress MGCP DLCX Return Code
4088
4089
Network Translated Address
Indicator
Reservation Request Accepted
Reservation Request Error Count
ATM Ingress Configured Profile
ATM Egress Configured Profile
ATM Negotiated Profile
4090
4091
4092
4093
4094
4095
4096
4098
4099
4201
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.4(1) and later
Release 9.4(1) and later
Route List Name
Route Name
Originating Leg DSP Statistics
Terminating Leg DSP Statistics
Originating Remote SIP Host
Release 9 and later (Named as Ingress SIP URL
in versions prior to the Release 9.7(3))
Originating Local SIP Host
4202
Release 9 and later (Named as Egress SIP URL
in versions prior to the Release 9.7(3))
SIP Call ID
4203
4204
4205
4206
4207
4208
4209
4210
4211
4212
4220
4221
4222
4223
4224
4225
4226
4232
Release 9 and later
Source IP Address
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.5(2) and later
Added in Release 9.5(2), modified in 9.6(1)
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.6(1) and later
Release 9.6(1) and later
Ingress Media Device Address
Egress Media Device Address
Initial Codec
Final Codec
Ingress Media Device Port
Egress Media Device Port
Originating VPN ID
Terminating VPN ID
Partial Calling Line Identity
Service Activation
PRI AOC Invoke Type
PRI AOC – S Charge Information
PRI AOC – D Charge Information
PRI AOC – E Charge Information
PRI AOC Invoke Failure
Rejecting Location Label
Rejecting Location Label Direction 4233
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-8
Aborted Attempt CDB Record (continued)
Tag
Field Name
Value Comments
H323 Destination
4236
4237
4239
4240
4241
4242
4243
4244
4245
4246
4247
4248
Release 9.7 and later
Added in a Release 9.5(2) patch
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Release 9.7 and later
Ingress Redirecting Number
Service Usage Data
CNAM DIP
Calling Name
Terminating Remote SIP Host
Terminating Local SIP Host
License Rejecting Reason
License Rejecting Direction
SIP Transport
SIP Routing URI Source
SIP Routing URI
When configured for milliseconds granularity
for timepoints fields
Millisecond Granularity Timepoint Fields
IAM Timepoint Received_ms
IAM Timepoint Sent_ms
ACM Timepoint Received_ms
ACM Timepoint Sent_ms
First REL Timepoint_ms
Second REL Timepoint_ms
RLC Timepoint Received_ms
RLC Timepoint Sent_ms
4100
4101
4102
4103
4106
4107
4108
4109
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
Release CDB Record (Tag: 1040/Release 5 or Later)
Table 1-9 lists data about the release CDB. CDB Tag 1040 is generated when the terminating CDB on a
call that went through and was answered and then released.
Table 1-9
Release CDB Record
Tag
Field Name
Value Comments
When configured for ITU encoding (Release 7 or
later)
ANSI Based Formatted Fields
Reason Code
2008
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-9
Release CDB Record (continued)
Tag
Field Name
Value Comments
When configured for ITU encoding (Release 7 or
later)
ITU Based Formatted Fields
Reason Code
3008
MGC Generic Tags
CDB Version
4000
4001
4002
4006
CDB Timepoint
Call Reference ID
REL Timepoint
When configured for seconds granularity
timepoints
Glare Encountered
RLC Timepoint
4019
4020
When configured for seconds granularity
timepoints
First Release Source
Total Meter Pulses
4028
4030
4044
4046
4047
4061
4062
4078
4079
4081
4082
4083
4084
4085
4086
Announcement Identification
Ingress Gateway Packet Info
Egress Gateway Packet Info
Tariff Rate
Restored as of Release 9.4(1)
Restored as of Release 9.4(1)
Scale Factor
Charge Band Number
Furnish Charging Information
T.38 Fax Call
Release 9.3(1) and later
Release 9.3(1) and later
Release 9.3(2) and later
Release 9.3(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Charge Unit Number
Charge Indicator
Outgoing Calling Party Number
MCID Request Indicator
MCID Response Indicator
Ingress MGCP DLCX Return Code 4087
Egress MGCP DLCX Return Code
4088
4089
Network Translated Address
Indicator
Reservation Request Accepted
Reservation Request Error Count
Route List Name
4090
4091
4095
4096
4097
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Route Name
MGCP Script Response String
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-9
Release CDB Record (continued)
Tag
Field Name
Value Comments
Originating Leg DSP Statistics
Terminating Leg DSP Statistics
Ingress Media Device Address
Egress Media Device Address
Initial Codec
4098
4099
4205
4206
4207
4208
4209
4210
4213
4214
4215
4216
4217
4218
4219
4221
4222
4223
4224
4225
4226
4227
4228
4229
4230
4231
4239
4240
4241
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.4(1) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Final Codec
Ingress Media Device Port
Egress Media Device Port
Meter Pulses Received
Meter Pulses Sent
Charge Tariff Info
Advice of Charge Indicator
Short Call Indicator
Charge Limit Exceeded
Call Recovered Indication
Service Activation
Added in Release 9.5(2), modified in 9.6(1)
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.5(2) and later
Release 9.6(1) and later
Release 9.6(1) and later
Release 9.6(1) and later
Release 9.6(1) and later
Release 9.6(1) and later
Release 9.7 and later
PRI AOC Invoke Type
PRI AOC – S Charge Information
PRI AOC – D Charge Information
PRI AOC – E Charge Information
PRI AOC Invoke Failure
RO/PR Executed
RO/PR Other Call Ref
RO/PR Replacement Trunk Group
RO/PR Replacement Chan ID
RO/PR Switchover Timestamp
Service Usage Data
CNAM DIP
Release 9.7 and later
Calling Name
Release 9.7 and later
When configured for ITU encoding (Release 7 or
later)
Millisecond Granularity Timepoint Fields
First REL Timepoint_ms
Second REL Timepoint_ms
RLC Timepoint Received_ms
RLC Timepoint Sent_ms
4106
4107
4108
4109
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-9
Release CDB Record (continued)
Tag
Field Name
Cisco Reserved Tags
Value Comments
Unique Call ID (Release 9 and later) 5000
Interrupted CDB Record (Tag: 1050/Release 5 or Later)
Table 1-10 lists data about the interrupted CDB. CDB Tag 1050 is created when a call is terminated
without a Release message. This happens for example, in hot standby configuration when dual Cisco
MGCs are used, and when failover occurs and the now active Cisco MGC discovers that a call is no
longer active (the release message probably arrived and was lost during the failover window).
Table 1-10
Interrupt CDB Record
Tag
Field Name
Value Comments
MGC Generic Tags
CDB Version
4000
4001
4002
4007
CDB Timepoint
Call Reference ID
Crash Timepoint
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
On-Going (Call) CDB Record (Tag: 1060/Release 5 or Later)
The On-going Call CDB (or Long-Call CDB) indicates that a call is still active after the expiration of
the time span defined in the XECfgParm.dat parameter *.LongCallTime. This CDB is generated again
each time the period defined in *.LongCallTime elapses while the call is active. For example, if
*.LongCallTime is set to its default value, 21600000 ms, which is equal to 6 hours, a 1060 CDB is
generated every 6 hours until the call is terminated.
Note
When the MGC is configured to create only the 1110 CDB (End-of-Call Summary) and this CDB, all of
the relevant 1060 tags are present and populated. This is because the 1060 CDB may be the first CDB
that is written for a call, if it has been active for the long-call period. In this case, the 1060 CDB contains
the full set of populated tags. However, when the MGC is configured to generate event-based CDBs
(such as 1010, 1020, 1030, 1040, 1050, 1060, 1070, and 1080) the 1060 CDB can contain only a subset
of tags: 5000, 4000–4002, 4213, and 4214. This occurs because the other event-based CDBs contain the
tag information, as they are associated with specific events. Therefore, in this instance the 1060 CDB
does not contain this redunant data, as it would be outside the primary purpose of this CDB.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-11 lists data about the on-going (Call) CDB.
Note
In Release 7 and later, the long duration includes more fields than it does in Release 5. The extra fields
are marked Release 7 and later.
Table 1-11
On-going CDB Record
Tag
Field Name
Value Comments
ANSI-Specific Tags
Egress Calling Number NOA
2018
2019
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
Egress Redirecting Number NOA
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
Egress Original Called Number NOA 2020
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
ITU-Specific Tags
Egress Calling Number NOA
3018
3019
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
Egress Redirecting Number NOA
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
Egress Original Called Number NOA 3020
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
MGC Generic Tags
CDB Version
4000
4001
4002
4003
Always present and populated in 1060.
Always present and populated in 1060.
Always present and populated in 1060.
CDB Timepoint
Call Reference ID
IAM Timepoint
Optional. Present only when 1110 is configured and if
system is configured for seconds timepoint.
ACM Timepoint
4004
4005
Optional. Present only when 1110 is configured and if
system is configured for seconds timepoint.
ANM/Answer Timepoint
Optional. Present only when 1110 is configured and if
system is configured for seconds timepoint.
Originating Trunk Group
Originating Member
4008
4009
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-11
On-going CDB Record (continued)
Tag
Field Name
Value Comments
Calling Number
4010
4012
4014
4015
4016
4066
4067
4068
4069
4070
4071
4072
4073
4080
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Dialed Number
Called Number
Terminating Trunk Group
Terminating Member
Ingress SigPath ID
Ingress Span ID
Ingress BearChan ID
Ingress ProtocolId
Egress SigPath ID
Egress Span ID
Egress BearChan ID
Egress ProtocolId
Original Called Number
Release 9.3(1) and later. Optional. Present only when
1110 is configured.
Meter Pulses Received
Meter Pulses Sent
4213
4214
4220
4237
Release 9.5(2) and later. Always present and
populated in 1060.
Release 9.5(2) and later. Always present and
populated in 1060.
Partial Calling Line Identity
Ingress Redirecting Number
Release 9.5(2) and later. Optional. Present only when
1110 is configured.
Added in a Release 9.5(2) patch. Present only when
1110 is configured. Not recorded for point-in-call
mode.
Millisecond Granularity Timepoint Fields
IAM Timepoint Received _ms
IAM Timepoint Sent_ms
4100
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
Optional. Present only when 1110 is configured.
4101
4102
4103
4104
4105
ACM Timepoint Received_ms
ACM Timepoint Sent_ms
ANM Timepoint Received_ms
ANM Timepoint Sent_ms
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
Always present and populated in 1060.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Maintenance CDB Record (Tag: 1070/Release 5 or Later)
Table 1-12 lists data about the maintenance record CDB type. CDB Tag 1070 is created for maintenance
activity (such as block or unblock) on a circuit.
Table 1-12
Maintenance CDB Record
Tag
Value
Field Name
MGC Generic Tags
CDB Version
4000
4001
4002
4017
4018
4032
4033
CDB Timepoint
Call Reference ID
Maint Trunk Group
Maint Circuit Member
Maint Type
Maint Reason (Retired in Release
9.4(1))
Maintenance SigPath ID
Maintenance Span ID
4074
4075
4076
4077
Maintenance BearChan ID
Maintenance Circuits Count
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
SS7 CIC Audit CDB Record (Tag: 1071/Release 9 or Later)
Table 1-13 lists data about the SS7 CIC audit record CDB type. This CDB is used to record changes to:
•
•
the number of circuits defined for a trunk group when the MGC is configured in Call Control mode
the number of circuits defined in a signaling service when the MGC is configured in Signaling mode.
This CDB is modeled after the 1070 CDB but does not contain independent CIC statuses, just total
counts of CICs defined and unavailable. It is triggered by provisioning changes to the number of circuits
in a trunk group (Call Control) or signaling service (Signaling).
Table 1-13
SS7 CIC Audio CDB Record
Tag
Field Name
Value Comments
MGC Generic Tags
CDB Version
4000
4001
CDB Timepoint
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-13
SS7 CIC Audio CDB Record (continued)
Tag
Field Name
Value Comments
Maint Trunk Group
4017
4074
Appears when the MGC is
configured for call control.
Maintenance SigPath ID
Appears when the MGC is
configured for signaling.
Total Circuit Count
4234
4235
added in 9.4(1) patch
added in 9.4(1) patch
Total Circuit Unavailable Count
Cisco Reserved Tags
Unique Call ID
5000
Note
CDB 1071 is configurable in XECfgParm.dat by adding it in engine.CDRmessageType; but if CDB 1110
is configured, CDB 1071 is suppressed.
Once configured in XECfgParm.dat, CDB 1071 is generated for the following conditions.
•
When the MML command sta-aud-cic is used to generate the current CIC availability information
on each configured ISUP trunk group or signaling service.
•
•
A provisioning change (add or delete) is made in the number of circuits.
A CIC service state or block state change occurs. A circuit that is unavailable is either blocked, OOS,
or both. A circuit that is blocked and also OOS is not double counted as unavailable circuits. The
following tables show the action taken when there is a service state or block state change.
Table 1-14
Service State Change
Service State Change
Blocked
Unblocked
OOS
IS
Do nothing Increment total unavailable counters
Do nothing Decrement total unavailable counters
Table 1-15
Service Block Change
Service Block Change
Block
OOS
IS
Do nothing Increment total unavailable counters
Do nothing Decrement total unavailable counters
Unblock
A blocked state is one or a combination of the following states:
•
•
•
•
Manual local block
Manual remote block
Auto remote block (hardware failure)
Auto local block
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
•
Propagation block (gateway initiated blocking)
CDB Tag 1071 generation rules:
•
If CDB Tag 1071 is generated as the result of the sta-aud-cic MML command, it includes the CIC
unavailability information per trunk group for switched configuration, or per signaling service for
nailed up. For other two scenarios, it only generates the information for the trunk groups that are
impacted.
•
•
CDB Tag 1071 is generated only on the active side.
To generate the CDB Tag 1071 on a trunk group or signaling service level rather than individual CIC
level to minimize CPS impact, an internal 10-second timer is used. 1071 CDB is generated 10
seconds after the initial CIC state change and/or the initial CIC provision change. This delay
prevents the flooding of 1071 CDBs if a large number of CICs have blocks or service state changes
almost simultaneously.
•
The sta-aud-cic MML command is rejected for the following conditions:
–
–
The MML command is attempted to be run on the standby side
CDB Tag 1071 is not configured in the XECfgParm.dat file
•
•
A circuit that has COT failure and has COT retest in progress is not counted as unavailable.
If the CDB Tag 1071 is configured to be generated for Cisco MGC software Release 9.5(2), that pre
BAMS 3.20 would require a skip-CDE for the CDB Tag 1071 record to be added to BAMS.
External Access CDB (Tag: 1080/Release 7 or Later)
Table 1-16 lists data about the external access CDB type. CDB Tag 1080 is generated whenever a query
is sent to an SCP (or other external device or database).
Table 1-16
External Access CDB Record
Tag
Field Name
Value Information Source
MGC Generic Tags
CDB Version
4000
CDB Timepoint
4001
4002
4040
4041
4042
4043
4049
4050
Time written
Universal Call Reference ID
TCAP Transaction Identification
Transaction Start Time
Transaction End Time
TCAP Database Identification
Service Logic ID
TCAP Transaction ID
Time that TCAP query was sent
Time that TCAP response was received
SCP Selection Number
SCP AMASlpID
AMALineNumber
SCP AMALineNumber (Analyze_Route)
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
File Header CDB (Tag: 1090/Release 7 or Later)
according to the CDB creation guidelines, where the first three fields are mandatory and are located in
their specified positions (refer to Table 1-17).
Note
This CDB is not configurable. Users cannot enable or disable the CDB nor can they select which fields
are to be included. This CDB always contains the fields shown in Table 1-17.
.
Table 1-17
File Header CDB Record
Tag
Field Name
Value Information Source
MGC Generic Tags
CDB Version
4000
CDB Timepoint
4001
4002
Time written
Universal Call Reference ID
Always 0 for compatibility with all other CDB
layouts
Miscellaneous Fields
File Start Time
6001
6000
6004
Host MGC ID
MGC Software Version
File Footer CDB (Tag: 1100/Release 7 or Later)
according to the CDB creation guidelines, where the first three fields are mandatory and are located in
their specified positions (refer to Table 1-18).
Note
This CDB is not configurable. Users cannot enable or disable the File Footer CDB nor can they select
which fields are to be included. This CDB always contains the fields shown in Table 1-18.
Table 1-18
File Footer CDB Record
Tag
Field Name
Value Information Source
MGC Generic Tags
CDB Version
4000
4001
CDB Timepoint
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-40
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-18
File Footer CDB Record (continued)
Tag
Field Name
Value Information Source
Call Reference ID
4002
This will always be 0, for compatibility with all
other CDB layouts.
Miscellaneous Fields
File End Time
6002
6003
6000
6004
Total Number of CDB Records
Host ID
MGC Software Version
End of the Call CDB (Tag: 1110/Release 7 or Later)
When the Cisco MGC software is configured to generate one CDB per call, a CDB is generated that
includes basic billing information. It is generated at the end of the call, as is the Release CDB, or an
attempted call that did not get to Setup status. That is, a call that did not get answered, as in an Aborted
Attempted CDB.
This End of Call CDB consists of the values listed in Table 1-19.
Table 1-19
End of Call CDB Record
ANSI
Tag
Value Description
ITU
Tag
Value Description
2000
2001
2003
2004
2005
2007
2008
2013
2015
2017
2018
Calling Party Category
3000
3001
3003
Calling Party Category
User Service Information
Calling number NOA
Charged number NOA
Dialed number NOA
Called Number NOA
Reason Code
User Service Information
Calling Number NOA
Does not exist for ITU
Dialed Number NOA
Called Number NOA
Reason Code
3005
3007
3008
Transit Network Selection
Carrier Selection Parameter
Redirecting Number NOA
3017
Redirecting Number NOA
Egress Calling Number NOA (Release 3018
9.5(2) and later)
Egress Calling Number NOA (Release
9.5(2) and later)
2019
2020
4000
Egress Redirecting Number NOA
(Release 9.5(2) and later)
3019
3020
4000
Egress Redirecting Number NOA
(Release 9.5(2) and later)
Egress Original Called Number NOA
(Release 9.5(2)) and later)
Egress Original Called Number NOA
(Release 9.5(2) and later)
CDB Version
CDB Version
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-41
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-19
End of Call CDB Record (continued)
ITU
ANSI
Tag
Tag
Value Description
Value Description
4001
4002
4008
4009
4010
4011
4012
4014
4015
4016
4028
4031
CDB Timepoint
4001
4002
4008
4009
4010
4011
4012
4014
4015
4016
4028
4031
CDB Timepoint
Call Reference ID
Call Reference ID
Originating Trunk Group
Originating Member
Calling Number
Originating Trunk Group
Originating Member
Calling Number
Charged Number
Charged Number
Dialed Number
Dialed Number
Called Number
Called Number
Terminating Trunk Group
Terminating Member
First Release Source
Terminating Trunk Group
Terminating Member
First Release Source
MGC Info Field (disabled as of
Release 7.3.x and 7.4.x)
MGC Info Field (disabled as of
Release 7.3.x and 7.4.x)
4034
4035
4036
4037
4046
4047
Ingress Originating Point Code
(Release 9.3(2) and up)
4034
4035
Ingress Originating Point Code
(Release 9.3(2) and up)
Ingress Destination Point Code
(Release 9.3(2) and up)
Ingress Destination Point Code
(Release 9.3(2) and up)
Egress Originating Point Code (Release 4036
9.3(2) and up)
Egress Originating Point Code (Release
9.3(2) and up)
Egress Destination Point Code (Release 4037
9.3(2) and up)
Egress Destination Point Code (Release
9.3(2) and up)
Ingress Gateway Packet Info (Restored 4046
as of Release 9.4(1))
Ingress Gateway Packet Info (Restored
as of Release 9.4(1))
Egress Gateway Packet Info (Restored 4047
as of Release 9.4(1))
Egress Gateway Packet Info (Restored
as of Release 9.4(1))
4060
4061
4062
4063
4065
Redirecting Number
Tariff Rate
4060
4061
4062
4063
4065
Redirecting Number
Tariff Rate
Scale Factor
Scale Factor
Test Line Indicator
Redirection Number
Test Line Indicator
Redirection Number (Release 9.7(3)
and later)
4068
4072
Ingress BearChan ID (Release 9.3(2)
and up)
4068
4072
Ingress BearChan ID (Release 9.3(2)
and up)
Egress BearChan ID (Release 9.3(2)
and up)
Egress BearChan ID (Release 9.3(2)
and up)
4078
4079
Charge Band Number
4078
4079
Charge Band Number (
Furnish Charging Information
Furnish Charging Information
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-19
End of Call CDB Record (continued)
ITU
ANSI
Tag
Tag
Value Description
Value Description
4080
4082
4083
Original Called Number
4080
4082
4083
Original Called Number
Charge Unit Number
Charge Unit Number
Charge Indicator (Release 9.5(2) and
up)
Charge Indicator(Release 9.5(2) and
up)
4084
4085
4086
4087
4088
4089
4090
4091
4092
4093
4094
4095
Outgoing Calling Party Number
(Release 9.5(2) and up)
4084
4085
4086
4087
4088
Outgoing Calling Party Number
(Release 9.5(2) and up)
MCID Request Indicator (Release
9.5(2) and up)
MCID Request Indicator (Release
9.5(2) and up)
MCID Response Indicator (Release
9.5(2) and up)
MCID Response Indicator (Release
9.5(2) and up)
Ingress MGCP DLCX Return Code
(Release 9.5(2) and up)
Ingress MGCP DLCX Return Code
(Release 9.5(2) and up)
Egress MGCP DLCX Return Code
(Release 9.5(2) and up)
Egress MGCP DLCX Return Code
(Release 9.5(2) and up)
Network Translated Address Indicator 4089
(Release 9.5(2) and up)
Network Translated Address Indicator
(Release 9.5(2) and up)
Reservation Request Accepted (Release 4090
9.5(2) and up)
Reservation Request Accepted (Release
9.5(2) and up)
Reservation Request Error Count
(Release 9.5(2) and up)
4091
4092
4093
4094
4095
4096
Reservation Request Error Count
(Release 9.5(2) and up)
ATM Ingress Configured Profile
(Release 9.5(2) and up)
ATM Ingress Configured Profile
(Release 9.5(2) and up)
ATM Egress Configured Profile
(Release 9.5(2) and up)
ATM Egress Configured Profile
(Release 9.5(2) and up)
ATM Negotiated Profiler (Release
9.5(2) and up)
ATM Negotiated Profile (Release 9.5(2)
and up)
Route List Name (Release 9.5(2) and
up)
Route List Name (Release 9.5(2) and
up)
4096
4097
Route Name (Release 9.5(2) and up)
Route Name (Release 9.5(2) and up)
MGCP Script Response String (Release 4097
9.5(2) and up)
MGCP Script Response String (Release
9.5(2) and up)
4098
4099
Originating Leg DSP Statistics (Release 4098
9.4(1) and up)
Originating Leg DSP Statistics (Release
9.4(1) and up)
Terminating Leg DSP Statistics
(Release 9.4(1) and up)
4099
Terminating Leg DSP Statistics
(Release 9.4(1) and up)
4100
4101
4102
4103
IAM Timepoint Received_msec
IAM Timepoint Sent_msec
4100
4101
4102
4103
IAM Timepoint Received_msec
IAM Timepoint Sent_msec
ACM Timepoint Received_msec
ACM Timepoint Sent_msec
ACM Timepoint Received_msec
ACM Timepoint Sent_msec
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-43
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-19
End of Call CDB Record (continued)
ITU
ANSI
Tag
Tag
Value Description
Value Description
4104
4105
4106
4107
4108
4109
4201
ANM Timepoint Received_msec
4104
4105
4106
4107
4108
4109
ANM Timepoint Received_msec
ANM Timepoint sent_msec
ANM Timepoint Sent_msec
First REL Timepoint_msec
Second REL Timepoint_msec
RLC Timepoint Received_msec
RLC Timepoint Sent_msec
First REL Timepoint_msec
Second REL Timepoint_msec
RLC Timepoint Received_msec
RLC Timepoint Sent_msec
Originating Remote SIP Host (Release 4201
9 and later)
Originating Remote SIP Host (Release
9 and later)
4202
Originating Local SIP Host (Release 9 4202
and later)
Originating Local SIP Host (Release 9
and later)
4203
4204
SIP Call ID (Release 9 and later)
4203
SIP Call ID (Release 9 and later)
Source IP Address (Release 9.4(1) and 4204
later)
Source IP Address (Release 9.4(1) and
later)
4205
4206
Ingress Media Device Address (Release 4205
9.4(1) and later)
Ingress Media Device Address (Release
9.4(1) and later)
Egress Media Device Address (Release 4206
9.4(1) and later)
Egress Media Device Address (Release
9.4(1) and later)
4207
4208
4209
Initial Codec (Release 9.4(1) and later) 4207
Final Codec (Release 9.4(1) and later) 4208
Initial Codec (Release 9.4(1) and later)
Final Codec (Release 9.4(1) and later)
Ingress Media Device Port (Release
9.4(1) and later)
4209
4210
4211
4212
Ingress Media Device Port (Release
9.4(1) and later)
4210
4211
4212
4213
4214
4215
4216
4217
Egress Media Device Port (Release
9.4(1) and later)
Egress Media Device Port (Release
9.4(1) and later)
Originating VPN ID (Release 9.4(1)
and later)
Originating VPN ID (Release 9.4(1)
and later)
Terminating VPN ID (Release 9.4(1)
and later)
Terminating VPN ID (Release 9.4(1)
and later)
Meter Pulses Received (Release 9.5(2) 4213
and later)
Meter Pulses Received (Release 9.5(2)
and later)
Meter Pulses Sent (Release 9.5(2) and 4214
later)
Meter Pulses Sent (Release 9.5(2) and
later)
Charge Tariff Info (Release 9.5(2) and 4215
later)
Charge Tariff Info (Release 9.5(2) and
later)
Advice of Charge Indicator (Release
9.5(2) and later)
4216
Advice of Charge Indicator (Release
9.5(2) and later)
Short Call Indicator (Release 9.5(2) and 4217
later)
Short Call Indicator (Release 9.5(2) and
later)
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-44
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-19
End of Call CDB Record (continued)
ITU
ANSI
Tag
Tag
Value Description
Value Description
4218
4219
4220
4221
4222
4223
4224
4225
4226
4227
4228
Charge Limit Exceeded (Release 9.5(2) 4218
and later)
Charge Limit Exceeded (Release 9.5(2)
and later)
Call Recovered Indication (Release
9.5(2) and later)
4219
4220
4221
Call Recovered Indication (Release
9.5(2) and later)
Partial Calling Line Identity (Release
9.5(2) and later)
Partial Calling Line Identity (Release
9.5(2) and later)
Service Activation (Added in Release
9.5(2), modified in Release 9.6(1))
Service Activation (Added in Release
9.5(2), modified in Release 9.6(1))
PRI AOC Invoke Type (Release 9.5(2) 4222
and later)
PRI AOC Invoke Type (Release 9.5(2)
and later)
PRI AOC – S Charge Information
(Release 9.5(2) and later)
4223
4224
4225
4226
PRI AOC – S Charge Information
(Release 9.5(2) and later)
PRI AOC – D Charge Information
(Release 9.5(2) and later)
PRI AOC – D Charge Information
(Release 9.5(2) and later)
PRI AOC – E Charge Information
(Release 9.5(2) and later)
PRI AOC – E Charge Information
(Release 9.5(2) and later)
PRI AOC Invoke Failure (Release
9.5(2) and later)
PRI AOC Invoke Failure (Release
9.5(2) and later)
Route Optimization/Path Replacement 4227
Action (Release 9.6(1) and later)
Route Optimization/Path Replacement
Action (Release 9.6(1) and later)
Route Optimization / Path Replacement 4228
Call Reference of Associated Call
Instance (Release 9.6(1) and later)
Route Optimization / Path Replacement
Call Reference of Associated Call
Instance (Release 9.6(1) and later)
4229
Route Optimization / Path Replacement 4229
Trunk Group Info (Release 9.6(1) and
later)
Route Optimization / Path Replacement
Trunk Group Info (Release 9.6(1) and
later)
4230
4231
4232
4233
4236
4237
4239
Route Optimization / Path Replacement 4230
Channel Info (Release 9.6(1) and later)
Route Optimization / Path Replacement
Channel Info (Release 9.6(1) and later)
Route Optimization Switchover
4231
4232
4233
4236
4237
4239
Route Optimization Switchover
Timestamp (Release 9.6(1) and later)
Timestamp (Release 9.6(1) and later)
Rejecting Location Label (Release
9.6(1) and later)
Rejecting Location Label (Release
9.6(1) and later)
Rejecting Location Label Direction
(Release 9.6(1) and later)
Rejecting Location Label Direction
(Release 9.6(1) and later)
H323 Destination (Release 9.7 and
later)
H323 Destination (Release 9.7 and
later)
Ingress Redirecting Number (Release
9.5(2) and later)
Ingress Redirecting Number (Release
9.5(2) and later)
Service Usage Data (Release 9.7 and
later)
Service Usage Data (Release 9.7 and
later)
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-45
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-19
End of Call CDB Record (continued)
ITU
ANSI
Tag
Tag
Value Description
Value Description
4240
4241
4242
CNAM DIP (Release 9.7 and later)
Calling Name (Release 9.7 and later)
4240
4241
CNAM DIP (Release 9.7 and later)
Calling Name (Release 9.7 and later)
Terminating Remote SIP Host (Release 4242
9.7 and later)
Terminating Remote SIP Host (Release
9.7 and later)
4243
4244
4245
Terminating Local SIP Host (Release
9.7 and later)
4243
Terminating Local SIP Host (Release
9.7 and later)
License Rejecting Reason (Release 9.7 4244
and later)
License Rejecting Reason (Release 9.7
and later)
License Rejecting Direction (Release
9.7 and later)
4245
License Rejecting Direction (Release
9.7 and later)
4246
4247
SIP Transport
4246
4247
SIP Transport (Release 9.7 and later)
SIP Routing URI Source
SIP Routing URI Source (Release 9.7
and later)
4248
5000
6005
SIP Routing URI
4248
5000
SIP Routing URI (Release 9.7 and later)
Unique Call ID (Release 9 and later)
Interim CDB (Release 9.5(2) and later)
Unique Call ID (Release 9 and later)
Interim CDB (Release 9.5(2) and later) 6005
Slave End-of-Call CDB Record (Tag: 1210/Release 9.6 or Later)
Table 1-20 lists data about the Slave End-of-Call CDB type. This CDB is defined to be used at the
end-of-call for a non-controlling half-call instance. Only end-of -call summary style CDBs are issued
for slave half-call instances and the appropriate information is check-pointed to ensure the data is
successfully written in the event of a switchover occurring. This CDB is disabled by default on your
Cisco PGW 2200.
Note
If you do enable this CDB and your network includes a Cisco BAMS, you must provision the Cisco
BAMS to ignore this CDB.
Table 1-20
Slave End-of-Call CDB Record
Tag
Field Name
Value Comments
MGC Generic Tags
Call Reference ID
IAM Timepoint
4002
4003
4006
4008
REL Timepoint
Originating Trunk Group
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-46
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
Detailed CDB Description
Table 1-20
Slave End-of-Call CDB Record (continued)
Tag
Field Name
Value Comments
Originating Member
Terminating Trunk Group
Terminating Member
RO/PR Executed
4009
4015
4016
4227
4228
Added in Release 9.6(1)
Added in Release 9.6(1)
RO/PR Other Call Ref
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
Slave Long Duration Call CDB Record (Tag: 1260/Release 9.6 or Later)
Table 1-21 lists data about the Slave Long Duration Call CDB type. This CDB is used when the call
instance remains active beyond a pre-configured time. The long call duration timer of the slave call is
the same as that of “master” call which is configured in XECfgParm.dat.
Table 1-21
Slave Long Duration Call CDB Record
Tag
Field Name
Value Comments
MGC Generic Tags
Call Reference ID
4002
4003
4008
4009
4015
4016
4227
4228
IAM Timepoint
Originating Trunk Group
Originating Member
Terminating Trunk Group
Terminating Member
RO/PR Executed
Added in Release 9.6(1)
Added in Release 9.6(1)
RO/PR Other Call Ref
Cisco Reserved Tags
Unique Call ID (Release 9 and later) 5000
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-47
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
CDE Detail Description
forms for each of the CDBs listed near the bottom in Table 1-22 are included in Table 1-23 through
Table 1-213.
Table 1-22
CDE Description Form Template
Name: Name of the call data element
Tag: Its tag value
Source: MGC
subsystem that
generates the CDE
value
Description/Purpose: Brief description of the CDE
Format: The format of the CDE value
Length: CDE value length
Data Value: Range of CDE values, or valid values
Extended Data Value: This section includes CDE values that are extended (from the ANSI/ITU standard) by the Cisco MGC.
General Information: General information about the CDE and comments.
MGC Release: The Cisco MGC release(s)
supporting this CDE
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-48
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
CDEs Encoded in ANSI
Calling Party Category (Tag: 2000/ANSI)
Table 1-23
Calling Party Category Description Form
Name: Calling Party Category
Tag: 2000
Source: MDL
Description/Purpose: Indicates what type of calling party is placing the call.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
The following codes are used in the calling party category (CPC) parameter field:
00000000 Calling party's category unknown (default)
00000001Operator, language French
00000010Operator, language English
00000011Operator, language German
00000100Operator, language Russian
00000101Operator, language Spanish
00000110|
00000111|-> Available to admin. For selecting a particular language.
00001000|
00001001Reserved
00001010Ordinary calling subscriber
00001011Ordinary calling subscriber with priority
00001100Data call
00000001Operator, language French
00001101Test call
00001110Spare
00001111Pay phone
00010000
toCCITT spare
11011111
11100000Emergency service call
11100001High priority emergency service call
11100010National security and emergency
11100011
toANSI spare
11110111
11110000
toNetwork-specific use
11111110
11111111Reserved
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-49
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
User Service Information (Tag: 2001/ANSI)
Table 1-24
User Service Information Description Form
Name: User Service Information
Tag: 2001
Source: MDL
Description/Purpose: This parameter is used to send the data transmission parameters to the distant exchange. The field
format is the same as the format for the bearer capability information element from ANSI standard T1.607.
Format: ANSI T1.113
Length in Octets: 2 to 13
Data Value: For more detail, please refer to ANSI T1.113.
Extension: octet continues through the next octet, 1 last octet
Coding standard: the setting should be 00 for CCITT standard, 10 for national
Information Transfer Capability. For POTS calling, this field is set at one of the following:
00000 Speech
01000 Unrestricted digital information
01001 Restricted digital information
10000 3.1 kHz audio
10001 Unrestricted digital information with tone and announcements
Transfer Mode (octet 2)
00 Circuit mode
10 Packet mode
7.3 Information Transfer Rate
00000 Packet mode only
10000 64 kb
00011 384 kb
10100 1472 kb
10101 1536 kb
10111 1920 kb
11000 Multi-rate
Structure, Configuration, Establishment, and so on: please refer to T1.113
Extended Data Value: No extended value.
General Information:
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Originating Line Information (Tag: 2002/ANSI)
Table 1-25
Originating Line Information Description Form
Name: Originating Line Information
Tag: 2002
Source: MDL
Description/Purpose: This information is captured from the originating line information parameter.
Format: ANSI T1.113
Data Value:
Length in Octets: 1
00000000
to
Binary equivalent of the digits
01100011
01100100
to
Reserved
11111111
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-51
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Calling Number Nature of Address (Tag: 2003/ANSI)
Table 1-26
Calling Number Nature of Address Description Form
Name: Calling Number Nature of Address Tag: 2003
Source: MDL
Description/Purpose: Indicates to the Cisco MGC how the number was delivered. It indicates the calling party type of
address. In POTS calling, two values are usually used: unique national number and nonunique national number.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
0000000 Spare
0000001 Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001 Nonunique subscriber number
1110010 Spare
1110011 Nonunique national number
111010 0 Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-52
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Charged Number Nature of Address (Tag: 2004/ANSI)
Table 1-27
Charged Number Nature of Address Description Form
Name: Charged Number Nature of Address Tag: 2004
Source: MDL
Description/Purpose: Indicates to the Cisco MGC how the number was delivered.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
0000000 Spare
0000001Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001
1110010
1110011
111010 0
1110101
1110110
1110111
1111000
to
Nonunique subscriber number
Spare
Nonunique national number
Nonunique international number
Spare
Spare
Test line
Reserved
1111000
1111111
Spare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-53
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Dialed Number Nature of Address (Tag: 2005/ANSI)
Table 1-28
Dialed Number Nature of Address Description Form
Name: Dialed Number Nature of Address
Tag: 2005
Source: MDL
Description/Purpose: Allows the Call Process to route a call differently based on the Nature of Address (NOA) value
provided in the IAM called number parameter. This tag represents the external (for example, line) value of NOA for the
called part number.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
0000000Spare - If the LEC doesn't know what type of line the calling party is, it will send this value to the Cisco MGC.
The Cisco MGC does not alter this value and does not do anything as far as billing with this field.
0000001Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001Nonunique subscriber number
1110010Spare
1110011Nonunique national number
111010 0Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-54
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
LRN Nature of Address (Tag: 2006/ANSI)
Table 1-29
LRN Nature of Address Description Form
Name: LRN Nature of Address
Tag: 2006
Source: MDL
Description/Purpose: Stores the NOA of LRN from an INAP query.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
0000000Spare
0000001Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001Nonunique subscriber number
1110010Spare
1110011Nonunique national number
111010 0Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-55
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Called Number Nature of Address (Tag: 2007/ANSI)
Table 1-30
Called Number Nature of Address Description Form
Name: Called Number Nature of Address
Tag: 2007
Source: MDL
Description/Purpose: The tag contains the Nature of Address (NOA) value from the egress protocol message used in the
outbound IAM. The NOA value in this tag is from the ingress protocol message. If no B number NOA is available
(redirected to an unknown number) but an original called number Information Element (IE) is available in the protocol
message, then the NOA from the IE is logged, and this can be modified for number normalization.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
0000000Spare - If the LEC doesn't know what type of line the calling party is, it will send this value to the Cisco MGC.
The Cisco MGC does not alter this value and does not do anything as far as billing with this field.
0000001Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001Nonunique subscriber number
1110010Spare
1110011Nonunique national number
111010 0Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-56
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Reason Code (Tag: 2008/ANSI)
Table 1-31
Reason Code Description Form
Name: Reason Code
Tag: 2008
Source: MDL
Description/Purpose: Incorporates SS7 release with cause values and any additional reasons that the basic call model
determines.
Format: ANSI T1.113
Length in Octets: 2
Data Value: The value of this field includes the first two octets of the cause indicators. Please refer to the ANSI T1.113
specification. (No diagnostic information included.)
Extended Data Value:
Note
Tag 2008 extends ANSI definition by adding COT failure indicators according to ANSI rules, with slight
modification as follows:
Octet 1:
Extension 0
Coding Standard 11
Spare 0
Location 0011
Octet 2:
Extension 1
Cause 1111110
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Forward Call Indicators Received (Tag: 2009/ANSI)
Table 1-32
Forward Call Indicators Received Description Form
Name: Forward Call Indicators Received
Tag: 2009
Source: MDL
Description/Purpose: This is for the received Forward Call Indicator parameter in ISUP message. It includes the following
fields: International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part Ind.;
ISDN User Part Preference Ind.; ISDN Access Ind.; and SCCP Method Ind.
Format: ANSI T1.113
Length in Octets: 2
Data Value:
National/International call indicator Bit A—For POTS calling, Bit A should be coded as a 0, signifying that this is an
incoming national call. A coding of 1 signifies that the call is an incoming international call.
End-to-end method indicator Bits CB:
00 No end-to-end method available.
01 Pass along method available.
10 SCCP method available.
11 Both Pass along and SCCP methods available.
Interworking indicator Bit D—This field indicates to the Cisco MGC if any interworking has been encountered in the type
of signaling for this call. No pertinent information needs to be acted upon by the Cisco MGC; it should pass the information
to the destination. “0” means no interworking was encountered (SS7 all the way). “1” means interworking was encountered.
IAM Segmentation indicator Bit E—In POTS calling, this segmentation indicator is marked with a 0.
ISDN User Part indicator Bit F, HG, I: This is a more granular field for use by the ISUP. In the United States, the ISUP is
used exclusively. For POTS national numbers, this field is marked 1 for ISUP used all the way. That is, if the Interworking
indicator is set at 0 there was no interworking. If the incoming call has a 0 in this field, there was interworking or the
incoming international call could have used TUP for signaling before reaching the national network. The Cisco MGC
should not have to deal with this bit; it should pass it on to the destination. For more details, please refer to the ANSI T1.113
specification.
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Forward Call Indicators Sent (Tag: 2010/ANSI)
Table 1-33
Forward Call Indicators Sent Description Form
Name: Forward Call Indicators Sent
Tag: 2010
Source: MDL
Description/Purpose: This is for the sent Forward Call Indicator parameter in ISUP message. It includes the following
fields: International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part
Ind.; ISDN User Part Preference Ind.; ISDN Access Ind.; and SCCP Method Ind.
Format: ANSI T1.113
Length in Octets: 2
Data Value: National/International call indicator Bit A—For POTS calling, Bit A should be coded as a 0, signifying
that this is an incoming national call. A coding of 1 signifies that the call is an incoming international call.
End-to-end method indicator Bits CB
00 No end to end method available.
01 Pass along method available.
10 SCCP method available.
11Both Pass along and SCCP methods available.
Interworking indicator Bit D—This field indicates to the Cisco MGC if any interworking has been encountered in the
type of signaling for this call. No pertinent information needs to be acted upon by the Cisco MGC; it should just pass
the information to the destination. “0” means no interworking encountered (SS7 all the way). “1” means interworking
was encountered.
IAM Segmentation indicator Bit E—In POTS calling, this segmentation indicator is marked with a 0.
ISDN User Part indicator Bit F, HG, I—This is a more granular field for use by the ISUP. In the United States, the ISUP
is used exclusively. For POTS national numbers, this field is marked 1 for ISUP used all the way. That is, if the
Interworking indicator is set at 0, there was no interworking. If the incoming call has a 0 in this field, there was
interworking or the incoming international call could have used TUP for signaling before reaching the national
network. The Cisco MGC should not have to deal with this bit; it passes it on to the destination. For more details, please
refer to the ANSI T1.113 specification.
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Nature of Connection Indicators Received (Tag: 2011/ANSI)
Table 1-34
Nature of Connection Indicators Received Description Form
Name: Nature of Connection Indicators
Tag: 2011
Source: MDL
Received
Description/Purpose: Used to record the Nature of Connection received from the IAM. Three possible indicators can be
received: the satellite indicator, the continuity check indicator, and the echo suppressor indicator.
Format: ANSI T1.113
Data Value:
Length in Octets: 1
Assume bit order HGFEDCBA
Satellite Indicator (Bits BA)—This field provides the Cisco MGC with information on how many satellites have been used
on this circuit. If the field is set to 00 and the Cisco MGC sends the circuit out on a circuit going over a satellite, the field
is incremented by one. The same goes for the other incoming settings (for example, 01 goes to 10 and 10 goes to 11). If
the outgoing circuit doesn't go over a satellite, the field is not incremented.
Continuity check indicator (Bits DC)—The Cisco MGC acts upon this field based on what is received. Also depending on
mutual agreements with the LECs, each outgoing trunk group sends Continuity tones to the terminating LECs with a
frequency between 0% to 100% of the time. This is configurable on a per trunk group basis. In addition, the Cisco MGC
interprets the incoming continuity field and passes the appropriate action to the Coding Unit.
Echo suppressor indicator (Bit E)—If this field is filled, the outgoing half echo control is already set on previous circuits,
there is no need for the terminating Cisco MGC to engage the EC. for this call. If the Cisco MGC activates the echo
canceller, this field needs to be set for the outgoing IAM message to subsequent switches.
Bits F-G: spare
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-60
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Nature of Connection Indicators Sent (Tag: 2012/ANSI)
Table 1-35
Nature of Connection Indicators Sent Description Form
Name: Nature of Connection Indicators
Tag: 2012
Source: MDL
Sent
Description/Purpose: Used to record the Nature of Connection sent. Three possible indicators can be sent: the satellite
indicator, the continuity check indicator, and the echo suppressor indicator.
Format: ANSI T1.113
Data Value:
Length in Octets: 1
Assume bit order HGFEDCBA
Satellite Indicator (Bits BA)—This field provides the Cisco MGC with information on how many satellites have been used
on this circuit. If the field is set to 00 and the Cisco MGC sends the circuit out on a circuit going over a satellite, the field
is incremented by one. The same goes for the other incoming settings (for example, 01 goes to 10 and 10 goes to 11). If
the outgoing circuit doesn't go over a satellite, the field is not incremented.
Continuity check indicator (Bits DC)—The Cisco MGC acts upon this field based on what is received. Also depending on
mutual agreements with the LECs, each outgoing trunk group sends Continuity tones to the terminating LECs with a
frequency between 0% to 100% of the time. This is configurable on a per trunk group basis. In addition, the Cisco MGC
interprets the incoming continuity field and passes the appropriate action to the Coding Unit.
Echo suppressor indicator (Bit E)—If this field is filled, the outgoing half echo control is already set on previous circuits,
there is no need for the terminating Cisco MGC to engage the EC. for this call. If the Cisco MGC activates the echo
canceller, this field needs to be set for the outgoing IAM message to subsequent switches.
Bits F-G: spare
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-61
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Transit Network Selection (Tag: 2013/ANSI)
Table 1-36
Transit Network Selection Description Form
Name: Transit Network Selection
Tag: 2013
Source: MDL
Description/Purpose: Includes Type of Network, Network Identification Plan, Digits, and Circuit Code.
Format: ANSI T1.113
Length in Octets: 4
Data Value:
Network Identification Plan—The Network ID plan field indicates to the Cisco MGC what type of ID the parameter has.
Since POTS calling uses the National Network Plan, there are two values that pertain to the Cisco MGC: 3-digit CIC and
4-digit CAC.
National Network ID:
0000 Unknown
00104 Digit Carrier Identification Code—If this value is used, the layout of the parameter is the second figure.
0011
to Spare
0111
1000
to Reserved for network specific use
1111
Type of Network Identification—This field holds the type of network identification for the transit network parameter.
000
010
CCITT
National Network ID
Spare bit
Digits 1, 2, 3 or Digits 1, 2, 3, 4—These fields hold the Carrier Identification Code of the international transit carrier that
is required.
Circuit Code—The circuit code field indicates to the carrier how the call was dialed. The following values are found in this
field:
0000 Unknown
0001 International call, no operator
0010 International call, operator requested
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-62
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Carrier Identification Parameter (Tag: 2014/ANSI)
Table 1-37
Carrier Identification Parameter Description Form
Name: Carrier Identification Parameter
Tag: 2014
Source: MDL
Description/Purpose: This is for the Carrier Identification Parameter in ISUP message. It includes the following fields:
Network Identification Plan; Type of Network Identification; Spare; Digit 1; Digit 2; Digit 3; Digit 4 or Null.
Format: ANSI T1.113
Length in Octets: 3 or 4
Data Value:
Network Identification Plan (1st Octet, Bits 4321)—Indicates what type of Carrier Identification the caller is requesting.
The Cisco MGC looks at this field to determine whether the requested CIC is a 3 digit or 4 digit code and how many digits
to expect in the Digits field.
Type of Network Identification(1st Octet, Bits 765)—Gives the identification of the network numbering plan. For POTS
calls from the LECs, the value of this field is 010 (National Network ID).
Spare(1st Octet, Bits 8)—Not applicable
Digit 1-3 or 1-4 (remaining two octets, Bits 8765 are all zeros if only 3 digits present)—Requested CIC
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Carrier Selection Parameter (Tag: 2015/ANSI)
Table 1-38
Carrier Selection Parameter Description Form
Name: Carrier Selection Parameter
Tag: 2015
Source: MDL
Description/Purpose: Indicates to the Cisco MGC how the caller dialed. This parameter can be used to determine how the
call will be routed. The parameter indicates to the Cisco MGC how the Carrier Access Code was dialed. With this
information and the Carrier Identification parameter, the Cisco MGC can route the call in a more granular fashion.
Format: ANSI T1.113
Data Value:
Length in Octets: 1
00000000 No indication
00000001 Selected Carrier Identification Code presubscribed and not input by calling party
00000010 Selected Carrier Identification Code presubscribed and input by calling party
00000011 Selected Carrier Identification Code presubscribed; but no indication of whether input by calling party
00000100 Selected Carrier Identification Code not presubscribed and input by calling party
00000101
to Spare
11111110
11111111 Reserved
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-63
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Jurisdiction Information Parameter (Tag: 2016/ANSI)
Table 1-39
Jurisdiction Information Parameter Description Form
Name: Jurisdiction Information Parameter Tag: 2016
Description/Purpose: This parameter provides numerical data indicating the geographic origination of the call.
Format: IA5 Length in Octets: 6
Source: MDL
Data Value: Digits from Jurisdiction Information Parameter.
Extended Data Value:
General Information:
MGC Release: Release 5.0 and later.
Redirecting Number Nature of Address (Tag 2017/ANSI)
Table 1-40
Redirecting Number Nature of Address Description Form
Name: Called Number Nature of Address
Tag: 2017
Source: MDL
Description/Purpose: NOA of Redirecting Number.
Format: ANSI T1.113
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001 Nonunique subscriber number
1110010 Spare
1110011 Nonunique national number
111010 0 Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.4.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-64
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Calling Number Nature of Address (Tag 2018/ANSI)
Table 1-41
Egress Calling Number Nature of Address Description Form
Name: Egress Calling Number NOA
Tag: 2018
Source: MDL
Description/Purpose: This CDE records the calling party NOA sent in the outgoing message by the MGC. This field
indicates the address type of the calling party. In POTS calling, there are usually two values that are used. They are Unique
National Number and Non-unique National Number.
Format: ANSI T1.113
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001 Nonunique subscriber number
1110010 Spare
1110011 Nonunique national number
1110100 Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-65
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Redirecting Number Nature of Address (Tag 2019/ANSI)
Table 1-42
Egress Redirecting Number Nature of Address Description Form
Name: Egress Redirecting Number NOA
Tag: 2019
Source: MDL
Description/Purpose: This CDE records the redirecting calling number NOA sent in the outgoing message by the MGC.
Format: ANSI T1.113
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001 Nonunique subscriber number
1110010 Spare
1110011 Nonunique national number
1110100 Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-66
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Original Called Number Nature of Address (Tag 2020/ANSI)
Table 1-43
Egress Calling Number Nature of Address Description Form
Name: Egress Original Called Number
Tag: 2020
Source: MDL
NOA
Description/Purpose: This CDE records the original called party NOA sent in the outgoing message by the MGC.
Format: ANSI T1.113
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Unique subscriber number
0000010 Spare (national use)
0000011 Unique national number
0000100 Unique international number
0000101
to Spare
1110000
1110001 Nonunique subscriber number
1110010 Spare
1110011 Nonunique national number
1110100 Nonunique international number
1110101 Spare
1110110 Spare
1110111 Test line
1111000
to Reserved
1111000
1111111 Spare
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-67
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
CDE Encoded as ITU Recommendation
Calling Party Category (Tag: 3000/ITU)
Table 1-44
Calling Party Category Description Form
Name: Calling Party Category
Tag: 3000
Source: MDL
Description/Purpose: Indicates what type of calling party is placing the call.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
00000000 Calling party’s category is unknown (national use).
00000001 Operator, language French
00000010Operator, language English
00000011Operator, language German
00000100Operator, language Russian
00000101Operator, language Spanish
00000110
toAvailable to Administrations for selecting a particular language by mutual agreement
00001000
00001001 Reserved (Refer to Recommendation Q.104) Can be used in national networks to indicate that the calling party
is a national operator
00001010Ordinary calling subscriber
00001011Calling subscriber with priority
00001100Data call (voice band data)
00001101Test call
00001110Spare
00001111Payphone
00010000
toSpare
11011111
11100000
to Reserved for national use
11111110
11111111Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
User Service Information (Tag: 3001/ITU)
Table 1-45
User Service Information Description Form
Name: User Service Information
Tag: 3001
Source: MDL
Description/Purpose: Captures the User Service Information parameter of ITU-T ISUP.
Format: ITU-T Q.763
Length in Octets: 2 to 13
Data Value:
8
7
6
5
4
3
2
1
1
Ext.
Ext.
Coding Standard
Transfer Mode
Information Transfer Capability
Information Transfer Rate
2
2a
Rate multiplier
3
Ext.
Ext.
Ext.
Layer identity
Layer identity
Layer identity
User information Layer 1 protocol
User information Layer 2 protocol
User information Layer 3 protocol
4
5
Notes:
1 Octet 2a is required if octet 2 indicates multirate (64 kbps base rate); otherwise it shall not be present.
2 Octets 3, 4, 5 or any combination of these octets may be omitted. Octet 3 may be extended as described in Table 4-6/Q.931
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
For French TUP, the following values apply:
8
7
6
5
4
3
2
1
1
Ext.
Coding Standard (00)
Information Transfer Capability (Mapped from OptaddRoutingInf)
Supported Values:
01
10
11
Speech
3.1 kHz
64 kbps
2
Ext.
Transfer Mode (00)
Information Transfer Rate (10000)
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-69
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Originating Line Information (Tag: 3002/ITU) Retired
Table 1-46
Originating Line Information Description Form
Name: Originating Line Information
Tag: 3002
Source: MDL
Description/Purpose: Indicates to the Cisco MGC what II digits are being sent from the LEC. This differentiates calls based
on the II digits.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
Extended Data Value: No extended value.
General Information: For more information on II digits, refer to the Telecordia Local Exchange Routing Guide.
MGC Release: Release 7.0 and later.
Note: This tag was retired in Release 7.4. It is no longer associated with any CDBs.
Calling Number Nature of Address (Tag: 3003/ITU)
Table 1-47
Calling Number Nature of Address Description Form
Name: Calling Number Nature of Address Tag: 3003
Source: MDL
Description/Purpose: Indicates to the Cisco MGC how the number was delivered. This field indicates the address type of
the calling party. In POTS calling, there are usually two values that are used: Unique national number and Nonunique
national number.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-70
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Charged Number Nature of Address (Tag: 3004/ITU) Retired
Table 1-48
Charged Number Nature of Address Description Form
Name: Charged Number Nature of Address Tag: 3004
Source: MDL
Description/Purpose: Indicates the address type of the calling party. In POTS calling, the value is typically Unique National
Number or Non-Unique National Number
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later. Retired in Release 9.1(2).
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-71
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Dialed Number Nature of Address (Tag: 3005)
Table 1-49
Dialed Number Nature of Address Description Form
Name: Dialed Number Nature of Address
Tag: 3005
Source: MDL
Description/Purpose: This value allows the Call Process to route a call differently based on the Nature of Address value
provided in the IAM Called Number parameter.
Format: ANSI T1.113
Length in Octets: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-72
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
LRN Nature of Address (Tag: 3006/ITU)
Table 1-50
LRN Nature of Address Description Form
Name: LRN Nature of Address
Tag: 3006
Source: MDL
Description/Purpose: Stores the NOA of LRN from an INAP query.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-73
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Called Number Nature of Address (Tag: 3007/ITU)
Table 1-51
Called Number Nature of Address Description Form
Name: Called Number Nature of Address
Tag: 3007
Source: MDL
Description/Purpose: The tag contains the Nature of Address (NOA) value from the egress protocol message used in the
outbound IAM.The NOA value in this tag is from the ingress protocol message. If no B number NOA is available
(redirected to an unknown number) but an original called number Information Element (IE) is available in the protocol
message, then the NOA from the IE is logged, and this can be modified for number normalization.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information: The value may be modified during the call because of IN actions (for example, LNP).
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-74
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Reason Code (Tag: 3008/ITU)
Table 1-52
Reason Code Description Form
Name: Reason Code
Tag: 3008
Source: MDL
Description/Purpose: Incorporates C7 release with cause values and any additional reasons that the basic call model
determines.
Format: based on ITU-T Q.850
Data Value:
Length in Octets: 2
Format:
8
7
6
5
4
3
2
1
1
2
Ext.
Ext.
Coding Standard
Spare
Location
Cause value
Note: This CDE does not include the Diagnostic and Recommendation octets defined in Q.850. The format of this CDR is
the same for both Q.763 and Q.931 signaling.
Extension:
0 Octet continues through the next octet (for example, octet 1 to 1a)
1 Last octet
Coding Standard
00 ITU-T standardized coding
01 ISO/IEC standard
10 National standard
11 Standard specific to identified location
Note: The coding standards other than ITU-T should only be used when the desired cause value cannot be represented with
the ITU-T standardized codeing.
Location:
0000 User (U)
0001 Private network serving the local user (LPN)
0010 Public network serving the local user (LN)
0011 Transit network (TN)
0100 Public network serving the remote user (RLN)
0101 Private network serving the remote user (RPN)
0111 International network (INTL)
1010 Network beyond interworking point (BI)
1100
to
Reserved for National use
1111
All other values are spare.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-75
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-52
Reason Code Description Form (continued)
Cause value: (only applicable in the context of Recommendations Q.763 and Q.931)
The cause value is divided into two fields, a class (bits 5 through 7) and a value within the class (bits 1 through 4).
The class indicates the general nature of the event. The valid values are as follows:
000 Normal event
001 Normal event
010 Resource unavailable
011 Service or option not available
100 Service or option not implemented
101 Invalid message (for example, parameter out of range)
111 Interworking
The valid class values are listed in Table 1-53.
Extended Data Value:
Note
Tag 3008 extends ANSI definition by adding COT failure indicators according to ANSI rules, with slight
modification as follows:
Octet 1:
Extension 0
Coding Standard 11
Spare 0
Location 0011
Octet 2:
Extension 1
Cause 1111110
General Information:
MGC Release: Release 7.0 and later.
The following table lists the Cause information element or parameter definitions for this tag.
Cause Information Element/Parameter Definitions
Table 1-53
Cause
Application Reference
(Note 1) (Note 2)
Location
(Note 3)
Class/Value/No. Definition
Remarks
000/0001/1
Unallocated (unassigned) number—indicates DSS 1, ISUP Q.931
that the called party cannot be reached
because, although the called party number is
in a valid format, it is not currently allocated
(assigned)
U, RPN,
LN
RLN, TN, No route by
INTL
digit analysis
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-76
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Application Reference
Cause
Location
(Note 3)
Class/Value/No. Definition
(Note 1)
(Note 2)
Remarks
000/0010/2
No route to specified transit network (national DSS 1,
Q.931
LN, TN
use)—indicates that the equipment sending
this cause has received a request to route the
call through a particular transit network which
it does not recognize. The equipment sending
this cause does not recognize the transit
network either because the transit network
does not exist or because that particular transit
network, while it does exist, does not serve the
equipment which is sending this cause.
ISUP(NU)
This cause is supported on a
network-dependent basis.
000/0010/3
000/0100/4
No route to destination—indicates that the
called party cannot be reached because the
network through which the call has been
routed does not serve the destination desired.
DSS 1, ISUP Q.931
U, RPN,
LN
This cause is supported on a network-
dependent basis.
Send special information tone— indicates that ISUP
the called party cannot be reached for reasons
that are of a long term nature and that the
special information tone should be returned to
the calling party.
Clause 7/Q.35
000/0101/5
000/0110/6
Misdialled trunk prefix (national
use)—indicates the erroneous inclusion of a
trunk prefix in the called party number.
ISUP(NU)
Channel unacceptable—indicates that the
channel most recently identified is not
acceptable to the sending entity for use in this
call.
DSS 1
DSS 1
Q.931
Q.931
LN
LN
000/0111/7
Call awarded and being delivered in an
established channel—indicates that the user
has been awarded the incoming call, and that
the incoming call is being connected to a
channel already established to that user for
similar calls (for example, packet-mode X.25
virtual calls).
000/1000/8
000/1001/9
Preemption—indicates that the call is being DSS 1, ISUP Q.735.3
MLPP
MLPP
pre-empted.
Q.955.3
Preemption – circuit reserved for
ISUP
Q.735.3
reuse—indicates that the call is being
pre-empted and the circuit is reserved for
reuse by the pre-empting exchange.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-77
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Application Reference
Cause
Location
(Note 3)
Class/Value/No. Definition
(Note 1)
(Note 2)
Remarks
000/1110/14
QoR:ported number—indicates that an
ISUP
Q.769.1
LN
exchange detected that the called number was
ported out (see Annex C/Q.769.1)
001/0000/16
Normal call clearing—indicates that the call DSS 1, ISUP Q.931,
U, RPN
is being cleared because one of the users
involved in the call has requested that the call
be cleared.
2.3/Q.764
Under normal situations, the source of this
cause is not the network.
001/0001/17
User busy— indicates that the called party is DSS 1, ISUP Q.931,
U, RPN,
RLN
Basic call and
call diversion
services
unable to accept another call because the user
busy condition has been encountered. This
cause value may be generated by the called
user or by the network. In the case of user
determine user busy, it is noted that the user
equipment is compatible with the call.
Q.732,
Q.733.3
001/0010/18
001/0011/19
No user responding—used when a called
party does not respond to a call establishment
message with either an alerting or connect
indication within the prescribed period of
time allocated.
DSS 1, ISUP Q.931,
Q.732
RLN
RLN
Call diversion
services
No answer from user (user alerted)—used
when the called party has been alerted but
does not respond with a connect indication
within a prescribed period of time.
DSS 1, ISUP Q.931
2.1.4/Q.764, RLN, TN, Expiry of
2.9.8.3/
Q.764
INTL
waiting ANM
timer (T9)
Q.732
RLN
Call diversion
services
Note
This cause is not necessarily
generated by Q.931 procedures but
may be generated by internalnetwork
timers.
001/0100/20
001/0101/21
Subscriber absent—used when a mobile
station has logged off, radio contact is not
obtained with a mobile station or if a personal
telecommunication user is temporarily not
addressable at any user-network interface.
DSS 1, ISUP
Mobile
application
Call rejected—indicates that the equipment
sending this cause does not wish to accept this
call, although it could have accepted the call
because the equipment sending this cause is
neither busy nor incompatible. This cause
may also be generated by the network,
indicating that the call was cleared due to a
supplementary service constraint..
DSS 1, ISUP Q.931
Q.732
U, RPN
RLN
Call diversion
services
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-78
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Cause
Application Reference
(Note 1) (Note 2)
Location
(Note 3)
Class/Value/No. Definition
Remarks
001/0110/22
Number changed—returned to a calling party DSS 1, ISUP Q.931
when the called party number indicated by the
calling party is no longer assigned. The new
called party number may optionally be
included in the diagnostic field. If a network
does not support this cause value, cause No. 1,
Unallocated (unassigned) number, shall be
used.
U, RPN,
LN
001/0111/23
Redirection to new destination—used by a
general ISUP protocol mechanism that can be
invoked by an exchange that decides that the
call should be set-up to a different called
number. Such an exchange can invoke a
redirection mechanism, by use of this cause
value, to request a preceding exchange
involved in the call to route the call to the new
number.
ISUP
001/1000/24
001/1001/25
Call rejected due to feature at the destination DSS 1, ISUP
RLN
Exchange – routing error—indicates that the ISUP
destination indicated by the user cannot be
reached, because an intermediate exchange
has released the call due to reaching a limit in
executing the hop counter procedure. This
cause is generated by an intermediate node,
which when decrementing the hop counter
value, gives the result 0.
LN, TN,
RLN,
ITNL
001/1010/26
001/1011/27
Non-selected user clearing—indicates that the DSS 1
user has not been awarded the incoming call.
Q.931
LN
Destination out of order—indicates that the
destination indicated by the user cannot be
reached because the interface to the
DSS 1, ISUP Q.931
RLN
destination is not functioning correctly. The
term "not functioning correctly" indicates that
a signaling message was unable to be
delivered to the remote party; for example, a
physical layer or data link layer failure at the
remote party, or user equipment off-line.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-79
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Cause
Application Reference
(Note 1) (Note 2)
Location
(Note 3)
Class/Value/No. Definition
Remarks
001/1100/28
Invalid number format (address
DSS 1, ISUP Q.931
U, RPN,
incomplete)—indicates that the called party
cannot be reached because the called party
number is not in a valid format or is not
complete.
RLN, LN
In Q.764, the TN, INTL The called
following
sections:
party number is
not in a valid
format or is not
complete
2.1.1, 2.1.2,
2.9.8.3, 2.2.5
Note
This condition may be determined
immediately after reception of an end
of pulsing (ST) signal, or on time-out
after the last received digit.
Annex A/
Q.763
TN, INTL,
RLN, RPN
001/1101/29
Facility rejected—returned when a
supplementary service requested by the user
cannot be provided by the network.
DSS 1, ISUP Q.931
RLN, U,
RPN, LN
TN, INTL Inability to
provide a
request
signaling
capability
Q.735.1
Q.737.1
Q.931
INTL,
RLN
CUG
INTL, TN, UUS
RLN
001/1110/30
Response to STATUS ENQUIRY—included DSS 1
in the STATUS message when the reason for
generating the STATUS message was the prior
receipt of a STATUS ENQUIRY message.
U, LN
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-80
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Cause
Application Reference
(Note 1) (Note 2)
Location
(Note 3)
Class/Value/No. Definition
Remarks
001/1111/31
Normal, unspecified—used to report a normal DSS 1, ISUP Q.931
event only when no other cause in the normal
RLN
In Q.764, the TN, INTL, Call failure
class applies.
following
sections:
RLN
information
indicating the
failure of a call
due to the lapse
of a timeout or
a fault not
2.1.1, 2.1.2,
2.8.1, 2.8.2,
2.9.3, 2.9.6,
2.9.8.2,
2.9.8.3,
2.1.8, 2.2.4
covered by
specific causes
(for example,
expiry of
timers Q.764
not covered by
specificcauses,
release of
interconnected
circuit, etc.)
2.1.6/Q.764 RLN, TN Expiry of
waiting INF
timer (T33)
2.9.7/Q.764
Annex A/
Q.763
010/0010/34
No circuit/channel available—indicates that DSS 1, ISUP Q.931,
U, RPN,
RLN, LN,
TN
there is no appropriate circuit/channel
presently available to handle the call.
Q.733.3
TN, INTL Circuit
congestion
encountered in
an exchange
010/0110/38
010/0111/39
Network out of order—indicates that the
network is not functioning correctly and that
the condition is likely to last a relatively long
period of time (for example, immediately
re-attempting the call is not likely to be
successful).
DSS 1, ISUP Q.931
U. RPN
Permanent frame mode connection out of
service—included in a STATUS message to
indicate that a permanently established frame
mode connection is out of service (for
example, due to equipment or section failure)
(see Annex A/Q.933).
DSS 1
Q.933
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-81
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Application Reference
Cause
Location
(Note 3)
Class/Value/No. Definition
(Note 1)
(Note 2)
Remarks
010/1000/40
Permanent frame mode connection
DSS 1
Q.933
operational—included in a STATUS message
to indicate that a permanently established
frame mode connection is operational and
capable of carrying user information (see
Annex A/Q.933).
010/1001/41
010/1010/42
Temporary failure—indicates that the
DSS 1, ISUP Q.931
U, RPN,
RLN, LN
network is not functioning correctly and that
the condition is not likely to last a long period
of time (for example, the user may wish to try
another call attempt almost immediately).
Switching equipment congestion—indicates DSS 1, ISUP
that the switching equipment generating this
TN, RLN,
INTL
cause is experiencing a period of high traffic.
2.9.9.1/
Q.764
TN, RLN Temporary
trunk block
(national use)
010/1011/43
Access information discarded—indicates that DSS 1, ISUP Q.931
the network could not deliver access
U, RPN,
LN
information to the remote user as requested,
that is, user-to-user information, low layer
compatibility, high layer compatibility, or
sub-address, as indicated in the diagnostic. It
is noted that the particular type of access
information discarded is optionally included
in the diagnostic.
010/1100/44
Requested circuit/channel not
available—returned when the circuit or
channel indicated by the requesting entity
cannot be provided by the other side of the
interface.
DSS 1, ISUP Q.931
U, RPN,
LN
010/1110/46
010/1111/47
011/0001/49
Precedence call blocked—indicates that there DSS 1, ISUP Q.735.3,
MLPP
are no preemptable circuits or that the called
user is busy with a call of equal or higher
preemptable level.
Q.955.3
Resource unavailable, unspecified—used to
report a resource unavailable event only when
no other cause in the resource unavailable
class applies.
DSS 1, ISUP Q.931
U, RPN
Annex A/
Q.763
Quality of Service not available—used to
report that the requested Quality of Service, as
defined in Recommendation X.213, cannot be
provided (for example, throughput or transit
delay cannot be supported).
DSS 1
Q.931
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-82
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Cause
Application Reference
(Note 1) (Note 2)
Location
(Note 3)
Class/Value/No. Definition
Remarks
011/0010/50
011/0101/53
011/0111/55
011/1001/57
011/1010/58
Requested facility not subscribed—indicates DSS 1, ISUP Q.931,
U, LN,
RLN
that the user has requested a supplementary
service which is implemented by the
Q.735
equipment which generated this cause, but
which the user is not authorized to use.
Outgoing calls barred within CUG—indicates ISUP
that although the calling party is a member of
the CUG for the outgoing CUG call, outgoing
calls are not allowed for this member of the
CUG.
Q.735.1
CUG
CUG
Incoming calls barred within CUG—indicates ISUP
that although the called party is a member of
the CUG for the incoming CUG call,
incoming calls are not allowed to this member
of the CUG.
Q.735.1
RLN
LN
Bearer capability not authorized—indicates
that the user has requested a bearer capability
which is implemented by the equipment
which generated this cause but the user is not
authorized to use.
DSS 1, ISUP Q.931
DSS 1, ISUP Q.931
Bearer capability not presently available—
indicates that the user has requested a bearer
capability which is implemented by the
equipment which generated this cause but
which is not available at this time.
LN
011/1110/62
011/1111/63
Inconsistency in designated outgoing access DSS 1, ISUP Q.735
information and subscriber class
Service or option not available,
DSS 1, ISUP Q.931
LN
LN
unspecified—used to report a service or
option not available event only when no other
cause in the service or option not available
class applies.
Annex A/
Q.763
100/0001/65
Bearer capability not implemented—indicates DSS 1, ISUP Q.931
that the equipment sending this cause does not
Annex A/
Q.763
TN, INTL Inability to
provide
support the bearer capability requested.
requested TMR
100/0010/66
100/0101/69
Channel type not implemented—indicates
that the equipment sending this cause does not
support the channel type requested.
DSS 1
Q.931
Requested facility not implemented—
indicates that the equipment sending this
cause does not support the requested
supplementary service.
DSS 1, ISUP Q.931,
Q.737.1
U, RPN,
LN, RLN
UUS
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-83
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Application Reference
Cause
Location
(Note 3)
Class/Value/No. Definition
(Note 1)
(Note 2)
Remarks
100/0110/70
Only restricted digital information bearer
DSS 1,
Q.931
capability is available (national use)—
indicates that the calling party has requested
an unrestricted bearer service but that the
equipment sending this cause only supports
the restricted version of the requested bearer
capability.
ISUP(NU)
100/1111/79
Service or option not implemented,
unspecified—used to report a service or
option not implemented event only when no
other cause in the service or option not
implemented class applies.
DSS 1, ISUP Q.931
Annex A/
Q.763
101/0001/81
101/0010/82
Invalid call reference value—indicates that
the equipment sending this cause has received
a message with a call reference which is not
currently in use on the user-network interface.
DSS 1
Q.931
U, LN
Identified channel does not exist—indicates DSS 1
that the equipment sending this cause has
received a request to use a channel not
activated on the interface for a call. For
example, if a user has subscribed to those
channels on a primary rate interface numbered
from 1 to 12 and the user equipment or the
network attempts to use channels 13 through
23, this cause is generated.
Q.931
101/0011/83
101/0100/84
A suspended call exists, but this call identity DSS 1
does not—indicates that a call resume has
been attempted with a call identity which
differs from that in use for any presently
suspended call(s).
Q.931
Q.931
LN
LN
Call identity in use—indicates that the
network has received a call suspended request
containing a call identity (including the null
call identity) which is already in use for a
suspended call within the domain of
interfaces over which the call might be
resumed.
DSS 1
101/0101/85
No call suspended—indicates that the
network has received a call resume request
containing a call identity information element
which presently does not indicate any
suspended call within the domain of
DSS 1
Q.931
LN
interfaces over which calls may be resumed.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-84
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Application Reference
Cause
Location
(Note 3)
Class/Value/No. Definition
(Note 1)
(Note 2)
Remarks
101/0110/86
Call having the requested call identity has
DSS 1
Q.931
LN
been cleared—indicates that the network has
received a call resume request containing a
call identity information element indicating a
suspended call that has in the meantime been
cleared while suspended (either by network
timeout or by the remote user).
101/0111/87
101/1000/88
User not member of CUG—indicates that the ISUP, DSS 1 Q.735.1
called user for the incoming CUG call is not a
member of the specified CUG or that the
calling user is an ordinary subscriber calling a
CUG subscriber.
RLN
CUG
Incompatible destination—indicates that the DSS 1, ISUP Q.931
equipment sending this cause has received a
U, RPN
RLN
ISUP
Q.737.1
UUS 2
CUG
request to establish a call which has low layer
compatibility, high layer compatibility, or
other compatibility attributes (for example,
data rate) which cannot be accommodated.
101/1010/90
101/1011/91
Non-existent CUG
ISUP
Q.735
Q.931
Invalid transit network selection (national
use)—indicates that a transit network
identification was received which is of an
incorrect format as defined in Annex C/
Q.931.
DSS 1,
ISUP(NU)
LN, TN
101/1111/95
110/0000/96
Invalid message, unspecified—used to report DSS 1, ISUP Q.931
an invalid message event only when no other
LN
Annex A/
cause in the invalid message class applies.
Q.763
Mandatory information element is missing— DSS 1
indicates that the equipment sending this
cause has received a message which is
missing an information element which must
be present in the message before that message
can be processed.
Q.931
U, LN
110/0001/97
Message type non-existent or not
DSS 1, ISUP Q.931
U, LN
implemented—indicates that the equipment
sending this cause has received a message
with a message type it does not recognize
either because this is a message not defined or
defined but not implemented by the
equipment sending this cause.
From Q.764, TN, INTL,
the following RLN
sections:
2.9.5.2,
2.9.5.3
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-85
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Application Reference
Cause
Location
(Note 3)
Class/Value/No. Definition
(Note 1)
(Note 2)
Remarks
110/0010/98
Message not compatible with call state or
DSS 1
Q.931
U, LN
message type non-existent or not
implemented—indicates that the equipment
sending this cause has received a message
such that the procedures do not indicate that
this is a permissible message to receive while
in the call state, or a STATUS message was
received indicating an incompatible call state.
110/0011/99
Information element/parameter non-existent DSS 1, ISUP Q.931
U, LN
or not implemented—indicates that the
2.9.5.2/
TN, INTL,
RLN
equipment sending this cause has received a
Q.764,
message which includes information
2.9.5.3/
element(s)/parameter(s) not recognized
Q.764,
because the information element
Annex A/
identifier(s)/parameter name(s) are not
Q.763
defined or are defined but not implemented by
the equipment sending the cause. This cause
indicates that the information element(s)/
parameter(s) were discarded. However, the
information element is not required to be
present in the message in order for the
equipment sending the cause to process the
message.
110/0100/100
Invalid information element
DSS 1
Q.931
U, LN
contents—indicates that the equipment
sending this cause has received an
information element which it has
implemented; however, one or more fields in
the information element are coded in such a
way which has not been implemented by the
equipment sending this cause.
110/0101/101
Message not compatible with call
state—indicates that a message has been
received which is incompatible with the call
state.
DSS 1
Q.931
U, LN
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-86
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-53
Cause Information Element/Parameter Definitions (continued)
Cause
Application Reference
(Note 1) (Note 2)
Location
(Note 3)
Class/Value/No. Definition
Remarks
110/0110/102
Recovery on timer expiry—indicates that a
DSS 1, ISUP Q.931
Q.733.4
procedure has been initiated by the expiry of a
timer in association with error handling
procedures.
RLN
Terminal
portability:
expiry of
waiting RES
(user) timer
2.4.3/Q.764 INTL
Expiry of
waiting RES
(network)
timer
(incoming
international
exchange)
110/0111/103
Parameter non-existent or not implemented – ISUP(NU)
passed on (national use)—indicates that the
equipment sending this cause has received a
message which includes parameters not
recognized because the parameters are not
defined or are defined but not implemented by
the equipment sending the cause. The cause
indicates that the parameter(s) were ignored.
In addition, if the equipment sending this
cause is an intermediate point, then this cause
indicates that the parameter(s) were passed on
unchanged.
110/1110/110
Message with unrecognized parameter
discarded—indicates that the equipment
sending this cause has discarded a received
message which includes a parameter that is
not recognized.
ISUP
2.9.5.2/
Q.764,
2.9.5.3/
Q.764
110/1111/111
111/1111/127
Protocol error, unspecified—used to report a DSS 1, ISUP Q.931
protocol error event only when no other cause
RLN
Annex A/
RLN, TN,
INTL
in the protocol error class applies.
Q.763
Q.735.1
RLN
CUG
Interworking, unspecified—indicates that
there has been interworking with a network
which does not provide causes for actions it
takes. Thus, the precise cause for a message
which is being sent cannot be ascertained.
DSS 1, ISUP Q.931
Annex A/
Q.763
Note 1: Application indicates that the cause value may be carried in DSS 1 and/or ISUP. Causes carried in ISUP which are
not marked for national use (NU) are the minimum set of cause values that shall be supported over the international interface.
Note 2: The references included are not exhaustive.
Note 3: These are typical locations generated within the scope of the associated Recommendations. Other locations may be
used depending upon the network configuration.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-87
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Forward Call Indicators Received (Tag: 3009/ITU)
Table 1-54
Forward Call Indicators Received Description Form
Name: Forward Call Indicators Received
Tag: 3009
Source: MDL
Description/Purpose: It is for the received Forward Call Indicator in ISUP message. It includes the following fields:
International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part Ind.; ISDN
User Part Preference Ind.; ISDN Access Ind.; SCCP Method Ind.
Format: ITU-T Q.763
Length in Octets: 2
Data Value:
8
7
6
F
5
E
4
D
L
3
C
K
2
B
J
1
A
I
1
2
H
P
G
O
N
M
The following codes are used in the forward call indicators parameter field:
bit A:National/international call indicator
0Call to be treated as a national call
1Call to be treated as an international call
This bit can be set to any value in the country of origin. In the international network this bit is not checked. In the destination
country, calls from the international network will have this bit set to 1.
bitsCBEnd-to-end method indicator (Bits B–F and J–K constitute the protocol control indicator)
00No end-to-end method available (only link-by-link method available)
01Pass along method available
10SCCP method available
11Pass along and SCCP methods available
bit D:Internetworking indicator
0No internetworking encountered (SS7 all the way)
1Internetworking encountered
bit E:National/international call indictor
0Call to be treated as a national call
1Call to be treated as an international call
bit F:ISDN user part indicator
0ISDN user part not used all the way
1ISDN user part used all the way
bitsHGISDN user part preference indicator
00ISDN user part preferred all the way
01ISDN user part not required all the way
10ISDN user part required all the way
11Spare
bit I:ISDN access indicator
0Originating access non-ISDN
1Originating access ISDN
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-88
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-54
Forward Call Indicators Received Description Form (continued)
bitsKJSCCP method indicator
00no indication
01Connectionless method available
10Connection oriented method available
11Connectionless and Connection oriented methods available
bit L:Spare
bits P-M:Reserved for national use
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value:
General Information:
MGC Release: Release 7.0 and later.
Forward Call Indicators Sent (Tag: 3010/ITU)
Table 1-55
Forward Call Indicators Sent Description Form
Name: Forward Call Indicators Sent
Tag: 3010
Source: MDL
Description/Purpose: It is for the sent Forward Call Indicator in ISUP message. It includes the following fields:
International Call Ind.; End To End Method Ind.; Interworking Ind.; IAM Segmentation Ind.; ISDN User Part Ind.; ISDN
User Part Preference Ind.; ISDN Access Ind.; SCCP Method Ind.
Format: ITU-T Q.763
Length in Octets: 2
Data Value:
8
7
6
F
5
E
4
D
L
3
C
K
2
B
J
1
A
I
1
2
H
P
G
O
N
M
The following codes are used in the forward call indicators parameter field:
bit A:National/international call indicator
0Call to be treated as a national call
1Call to be treated as an international call
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-89
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-55
Forward Call Indicators Sent Description Form (continued)
This bit can be set to any value in the country of origin. In the international network this bit is not checked. In the destination
country, calls from the international network will have this bit set to 1.
bitsCBEnd-to-end method indicator (Bits B–F and J–K constitute the protocol control indicator)
00No end-to-end method available (only link-by-link method available)
01Pass along method available
10SCCP method available
11Pass along and SCCP methods available
bit D:Internetworking indicator
0No internetworking encountered (SS7 all the way)
1Internetworking encountered
bit E:National/international call indictor
0Call to be treated as a national call
1Call to be treated as an international call
bit F:ISDN user part indicator
0ISDN user part not used all the way
1ISDN user part used all the way
bitsHGISDN user part preference indicator
00ISDN user part preferred all the way
01ISDN user part not required all the way
10ISDN user part required all the way
11Spare
bit I:ISDN access indicator
0Originating access non-ISDN
1Originating access ISDN
bitsKJSCCP method indicator
00no indication
01Connectionless method available
10Connection oriented method available
11Connectionless and Connection oriented methods available
bit L:Spare
bits P-M:Reserved for national use
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value:
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-90
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Nature of Connection Indicators Received (Tag: 3011/ITU)
Table 1-56
Nature of Connection Indicators Received Description Form
Name: Nature of Connection Indicators
Tag: 3011
Source: MDL
Received
Description/Purpose: Used to record the Nature of Connection received from the IAM. There are three possible indicators
that can be received: the satellite indicator, the continuity check indicator, and the echo suppressor indicator.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
8
7
6
5
4
3
2
1
H
G
F
E
D
C
B
A
The following codes are used in the nature of connection indicators parameter field:
bitsBASatellite indicator
00No satellite circuit in the connection
01One satellite circuit in the connection
10Two satellite circuits in the connection
11Spare
bitsDCContinuity check indicator
00Continuity check not required
01Continuity check required on this circuit
10Continuity check performed on a previous circuit
11Spare
bit E:Echo control device indicator
0Outgoing half echo control device not included
1Outgoing half echo control device included
bitsF-HSpare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value:
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-91
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Nature of Connection Indicators Sent (Tag: 3012/ITU)
Table 1-57
Nature of Connection Indicators Sent Description Form
Name: Nature of Connection Indicators
Tag: 3012
Source: MDL
Sent
Description/Purpose: Used to record the Nature of Connection sent from the IAM. There are three possible indicators that
can be received: the satellite indicator, the continuity check indicator, and the echo suppressor indicator.
Format: ITU-T Q.763
Length in Octets: 1
Data Value:
8
7
6
5
4
3
2
1
H
G
F
E
D
C
B
A
The following codes are used in the nature of connection indicators parameter field:
bitsBASatellite indicator
00No satellite circuit in the connection
01One satellite circuit in the connection
10Two satellite circuits in the connection
11Spare
bitsDCContinuity check indicator
00Continuity check not required
01Continuity check required on this circuit
10Continuity check performed on a previous circuit
11Spare
bit E:Echo control device indicator
0Outgoing half echo control device not included
1Outgoing half echo control device included
bitsF-HSpare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for
your variant with the appropriate specification, if necessary.
Extended Data Value:
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-92
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Transit Network Selection (Tag: 3013/ITU)
Table 1-58
Transit Network Selection Description Form
Name: Transit Network Selection
Tag: 3013
Source: MDL
Description/Purpose: Used to identify each previous network type transited.
Format: ITU-T Q.763
Length in Octets: 1-n
Data Value:
8
7
6
5
4
3
2
1
1
2
Odd/Even
Type of network identification
Network identification plan
.
.
Network identification
.
2n
The following codes are used in the subfields of the transit network selection parameter field:
Odd/even indicator
0Even number of digits
1Odd number of digits
Type of network identification
000CCITT-standardized identification
010National network identification
otherSpare
Network identification plan
For CCITT-standardized identification:
0000Unknown
0011Public data network identification code (DNIC), Recommendation X.121
0110 Public land mobile network identification code (MNIC), Recommendation E.212
otherSpare
For national network identification, this information is coded according to national specifications.
Network identification
This information is organized according to the network identification plan and the identified coding principle.
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value:
General Information: This value is used only with the following ITU ISUPs: HONG_KONG, AUSTRALIAN, FRENCH,
NTT, and JAPAN. It can also be used for national ISUPs, within any particular country, with private designations for the
network type. For a national call, such as ANSI, this tag is generated along with 2014.205
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-93
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Redirecting Number Nature of Address (Tag 3017/ITU)
Table 1-59
Redirecting Number Nature of Address Description Form
Name: Called Number Nature of Address
Tag: 3017
Source: MDL
Description/Purpose: Indicates to the Cisco MGC how the number was delivered. It indicates the calling party address type.
In POTS calling, there are usually two values that are used: Unique national number and Nonunique national number.
Format: ITU-T Q.763
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.4.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-94
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Calling Number Nature of Address (Tag 3018/ITU)
Table 1-60
Egress Calling Number Nature of Address Description Form
Name: Egress Calling Number NOA
Tag: 3018
Source: MDL
Description/Purpose: This CDE records the calling party NOA sent in the outgoing message by the MGC. This field
indicates the address type of the calling party. In POTS calling, there are usually two values that are used. They are Unique
National Number and Non-unique National Number.
Format: ANSI T1.113
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-95
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Redirecting Number Nature of Address (Tag 3019/ITU)
Table 1-61
Egress Redirecting Number Nature of Address Description Form
Name: Egress Redirecting Number NOA
Tag: 3019
Source: MDL
Description/Purpose: This CDE records the redirecting calling number NOA sent in the outgoing message by the MGC.
Format: ITU-T Q.763
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-96
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Original Called Number Nature of Address (Tag 3020/ITU)
Table 1-62
Egress Calling Number Nature of Address Description Form
Name: Egress Original Called Number
Tag: 3020
Source: MDL
NOA
Description/Purpose: This CDE records the original called party NOA sent in the outgoing message by the MGC.
Format: ITU-T Q.763
Length in Octet: 1
Data Value:
0000000 Spare
0000001 Subscriber number (national)
0000010 Unknown (national)
0000011 National (significant) number
0000100 International number
0000101
to Spare
1101111
1110000
to Reserved for national use
1111110
1111111 Spare
Note: The above values are for standard ITU SS7. Variants of ITU SS7 may have different values. Verify the values for your
variant with the appropriate specification, if necessary.
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-97
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
MGC Generic CDEs
CDB Version (Tag: 4000)
Table 1-63
CDB Version Description Form
Name: CDB Version
Tag: 4000
Source: MDL
Description/Purpose: Holds CDB version number to control raw CDB layout version.
Format: BE
Length in Octets: 1
Data Value: 1
Extended Data Value: No extended value.
General Information: This field is required in every CDB.
MGC Release: Release 5.0 and later.
CDB Timepoint (Tag: 4001)
Table 1-64
CDB Timepoint CDE Description Form
Name: CDB Timepoint
Tag: 4001
Source: MDL/Engine
Description/Purpose: Timepoint for creation of the CDB.
Format: BE
Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This field is required in every CDB.
MGC Release: Release 5.0 and later.
Call Reference ID (Tag: 4002)
Table 1-65
Call Reference ID Description Form
Name: Call Reference ID
Tag: 4002
Source: MDL/Engine
Description/Purpose: The Call Reference ID is created by the call processing engine as a unique Call ID. Multiple CDBs
have this Call Reference ID to associate the CDBs that create the call.
The purpose of this field is to uniquely identify a single call. This field is used by downstream systems (such as mediation)
to correlate CDBs and create a single CDR record.
Format: BE
Length in Octets: 8
Data Value: This consists of a 32-bit time and a 32-bit ascending sequence number.
Extended Data Value: No extended value.
General Information: This field is required in every CDB.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-98
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
IAM/Setup Timepoint (Tag: 4003)
Table 1-66
IAM/Setup Timepoint Description Form
Name: IAM/Setup Timepoint
Tag: 4003
Source: MDL/Engine
Description/Purpose: Timepoint for receipt of IAM/Setup (or receipt of CRM if a CRM preceded the IAM).
Format: BE Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This message is sent in the forward direction (from the originating exchange to the terminating
exchange) to initiate seizure of an outgoing circuit and to transmit the number and other information relating to the routing
and handling of a call.
MGC Release: Release 5.0 and later.
ACM/Alert Timepoint (Tag: 4004)
Table 1-67
ACM/Alert Timepoint Description Form
Name: ACM/Alert Timepoint
Tag: 4004
Source: MDL/Engine
Description/Purpose: Timepoint for receipt of ACM/Alert.
Format: BE
Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This message is sent in the backward direction (from the terminating exchange to the originating
exchange), indicating that all signals required for routing the call to the called party have been received.
MGC Release: Release 5.0 and later.
ANM/Answer Timepoint (Tag: 4005)
Table 1-68
ANM/Answer Timepoint Description Form
Name: ANM/Answer Timepoint
Description/Purpose: Timepoint for receipt of ANM/Answer.
Format: BE Length in Octets: 4
Tag: 4005
Source: MDL/Engine
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This message is sent in the backward direction (from the terminating exchange to the originating
exchange), indicating that the call has been answered.
This message can be used in conjunction with the charging information to start measurement of a call duration.
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-99
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
REL/Release Timepoint (Tag: 4006)
Table 1-69
REL/Release Timepoint Description Form
Name: REL/Release Timepoint
Tag: 4006
Source: MDL/Engine
Description/Purpose: Timepoint for receipt of first REL/Release.
Format: BE Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This message can be sent in either direction indicating that the circuit identified in the message is
being released due to the reason (cause) supplied and is ready to be put in idle state on receipt of the release complete
message.
This message provides the release of the circuit of a call initiated by the IAM message.
MGC Release: Release 5.0 and later.
Crash Timepoint (Tag: 4007)
Table 1-70
Crash Timepoint Description Form
Name: Crash Timepoint
Tag: 4007
Source: MDL/Engine
Description/Purpose: Last known timepoint before a crash.
Format: BE
Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Originating Trunk Group (Tag: 4008)
Table 1-71
Originating Trunk Group Description Form
Name: Originating Trunk Group
Tag: 4008
Source: MDL/Engine
Description/Purpose: Holds the originating trunk group number.
Note
If you are using the Multiple Incoming IP Trunk Groups feature, this CDR contains the derived incoming trunk
group ID.
Format: BE
Length in Octets: 2
Data Value: The trunk group number ranges from 1 to 16,384 for ANSI and 1 to 4096 for ITU.
Extended Data Value: No extended value.
General Information: When creating Bellcore AMA Format (BAF) records downstream, BAF supports only 4 digits for the
trunk group number. This makes the practical limit 9999.
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-100
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Originating Member (Tag: 4009)
Table 1-72
Originating Member Description Form
Name: Originating Member
Tag: 4009
Source: MDL
Description/Purpose: Contains the originating trunk member number within the originating trunk group. There can be 214
originating members when the MGC is configured for ANSI, and 212 originating members when configured for ITU.
Format: BE
Length in Octets: 2
Data Value: There can be 214 members for ANSI, and 212 for ITU, and is represented as an integer.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Calling Number (Tag: 4010)
Table 1-73
Calling Number Description Form
Name: Calling Number
Description/Purpose: These are the numbers of the calling number.
Format: IA5 Length in Octets: 1 to 96
Tag: 4010
Source: MDL
Data Value: Holds the digits of the calling number.
Extended Data Value: No extended value.
General Information: In the SS7/C7 environment, the calling number (Tag 4010) holds only the digits of the calling number;
it does not include any NOA, or other information. NOA and other information are presented by their own CDE(s).
MGC Release: Release 5.0 and later.
Charged Number (Tag: 4011)
Table 1-74
Charged Number Description Form
Name: Charged Number
Tag: 4011
Source: MDL
Description/Purpose: If the protocol contains a parameter called charged number the contents are deposited into this CDE
in order to define unique number of the party to be billed. In this case, it may or may not be the calling number. However,
if the charged number parameter does not exist, the calling number is placed by default into this CDE as a default billed
party.
Format: IA5
Length in Octets: 1 to 96
Data Value: The digits of the number being billed.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-101
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Dialed Number (Tag: 4012)
Table 1-75
Dialed Number Description Form
Name: Dialed Number
Tag: 4012
Source: MDL
Description/Purpose: These are the digits that were dialed by the calling party.
Format: IA5 Length in Octets: 1 to 96
Data Value: The digits that were dialed by the calling party.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
LRN Number (Tag: 4013)
Table 1-76
LRN Number Description Form
Name: LRN Number
Tag: 4013
Source: MDL
Description/Purpose: Locations routing number (LRN) used in implementation of local number portability.
Format: IA5
Length in Octets: 1 to 96
Data Value: IA5 digits
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Called Number (Tag: 4014)
Table 1-77
Called Number Description Form
Name: Called Number
Tag: 4014
Source: MDL
Description/Purpose: This is the number to which the call is sent. This tag contains egress message information sent out in
the outbound IAM.
Format: IA5
Length in Octets: 1 to 96
Data Value: The digits for the number to which the call is sent.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-102
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Terminating Trunk Group (Tag: 4015)
Table 1-78
Terminating Trunk Group Description Form
Name: Terminating Trunk Group
Tag: 4015
Source: MDL/Engine
Description/Purpose: Terminating Trunk Group number.
Format: BE Length in Octets: 2
Data Value: The terminating trunk group number ranges from 1 to 16,384 when the MGC is configured for ANSI and the
number ranges from 1 to 4096 when it is configured for ITU.
Extended Data Value: No extended value.
General Information: When creating BAF records downstream, BAF supports only 4 digits for trunk group number. This
makes the practical limit 9999.
MGC Release: Release 5.0 and later.
Terminating Member (Tag: 4016)
Table 1-79
Terminating Member Description Form
Name: Terminating Member
Tag: 4016
Source: MDL/Engine
Description/Purpose: Contains the terminating trunk member number within the terminating trunk group. There can be 214
members when the terminating trunk group is configured for ANSI, and up to 212 members when it is configured for ITU.
Format: BE
Length in Octets: 2
Data Value: There can be up to 16,384 terminating members for ANSI, and up to 4096 members for ITU, and is represented
as an integer.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Maintenance Trunk Group (Tag: 4017)
Table 1-80
Maintenance Trunk Group Description Form
Name: Maintenance Trunk Group
Description/Purpose: Maintenance trunk group number involved for maintenance.
Format: BE Length in Octets: 2
Tag: 4017
Source: MDL/Engine
Data Value: The trunk group number ranges from 1 to 16,384 for ANSI and 1 to 4096 for ITU.
Extended Data Value: No extended value.
General Information: When creating BAF records downstream, BAF supports only 4 digits for trunk group number. This
makes the practical limit 9999.
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-103
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Maintenance Circuit Member (Tag: 4018)
Table 1-81
Maintenance Circuit Member
Name: Maintenance Circuit Member
Tag: 4018
Source: MDL/Engine
Description/Purpose: Maintenance circuit member number within a trunk group. There can be up to 214 members in a trunk
group when the MGC is configured for ANSI and up to 212 members when configured for ITU.
Format: BE
Length in Octets: 2
Data Value: There can be up to 16,384 members for ANSI and up to 4096 members for ITU, and is represented as an integer.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Glare Encountered (Tag: 4019)
Table 1-82
Glare Encountered Description Form
Name: Glare Encountered
Tag: 4019
Source: MDL
Description/Purpose: Call completed but glare was encountered during the call.
Format: BE
Length in Octets: 1
Data Value:
0 = No Glare
1 = Glare
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
RLC/RELEASE Complete Timepoint (Tag: 4020)
Table 1-83
RLC/Release Complete Timepoint Description Form
Name: RLC/Release Complete
Description/Purpose: Timepoint for receipt of RLC/Release complete.
Format: BE Length in Octets: 4
Tag: 4020
Source: MDL/Engine
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-104
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
First Release Source (Tag: 4028)
Table 1-84
First Release Source Description Form
Name: First Release Source
Tag: 4028
Source: MDL
Description/Purpose: Indicates if the release source was an originating, terminating, or local (Cisco MGC) system.
Format: BE
Length in Octets: 1
Data Value:
0 = Originating side
1 = Terminating side
2 = Local (MGC)
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
LNP Dip (Tag: 4029)
Table 1-85
LNP Dip Description Form
Name: LNP Dip
Tag: 4029
Source: MDL
Description/Purpose: Indicates if an LNP dip was performed.
Format: BE
Length in Octets: 1
Data Value:
0 = Not required
1 = Required and succeeded
2 = Not required, previous switch accomplished LNP
3 = Required, failed
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-105
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Total Meter Pulses (Tag: 4030)
Table 1-86
Total Meter Pulses Description Form
Name: Total Meter Pulses
Tag: 4030
Source: MDL
Description/Purpose: Holds the total meter pulses. Certain Integrated Services Digital Network User Parts (ISUPs) and
Telephone User Parts (TUPs) support this optional information.
Format: BE
Length in Octets: 2
Data Value: Total meter pulse counts sent out by Cisco MGC for a call.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later. To be retired after Release 9.5(2).
Maintenance Type (Tag: 4032)
Table 1-87
Maintenance Type Description Form
Name: Maintenance Type
Tag: 4032
Source: MDL
Description/Purpose: Indicates the type of maintenance requested.
Format: BE
Length in Octets: 1
Data Value:
Up to Release 9.2(2):
1 = Block
2 = Unblock
3 = Reset
Release 9.3(1) and later:
1 = Blocked channel remote
2 = Unblocked channel remote
3 = Reset or restart channel remote
4 = Reset channel local
5 = Blocked channel local
6 = Unblocked channel local
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-106
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Maintenance Reason (Tag: 4033)—Retired
Table 1-88
Maintenance Reason Description Form
Name: Maintenance Reason
Tag: 4033
Source: MDL
Description/Purpose: Indicates the reason that the maintenance was requested.
Format: BE
Length in Octets: 1
Data Value:
Up to Release 9.2(2):
1 = Remote
2 = Local
Release 9.3(1) and later:
1 = Blocked channel remote
2 = Unblocked channel remote
3 = Reset or restart channel remote
4 = Reset channel local
5 = Blocked channel local
6 = Unblocked channel local
Extended Data Value: No extended value.
General Information:
MGC Release: Release 5.0 and later.
Note
Tag 4033is retired in Release 9.4(1) of the Cisco MGC software.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-107
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Ingress Originating Point Code (Tag: 4034)
Table 1-89
Ingress Originating Point Code Description Form
Name: Ingress Originating Point Code
Tag: 4034
Source: MDL
Description/Purpose: Holds the ingress originating point code.
Format: BE Length in Octets: 4
Data Value: The point code is in 4-byte integer format.
Extended Data Value: No extended value.
General Information:
Conversion example of point code from 4-byte integer to IA5 format:·
•
•
ITU C7 point code (3 bits - 8bits - 3bits)
Tag value in integer format = 4114
Convert tag value in binary format = 1000000010010
Convert tag value in IA5 format = 10-00000010-010 (2-2-2)
ANSI SS7 point code (8 bits - 8 bits - 8 bits)
Tag value in integer format = 131586
Convert tag value in binary format = 100000001000000010
Convert tag value in IA5 format = 10-00000010-00000010 (2-2-2)
MGC Release: Release 7.0 and later.
Ingress Destination Point Code (Tag: 4035)
Table 1-90
Ingress Destination Point Code Description Form
Name: Ingress Destination Point Code
Tag: 4035
Source: MDL
Description/Purpose: Holds the ingress destination point code.
Format: BE Length in Octets: 4
Data Value: The point code is in 4-byte integer format.
Extended Data Value: No extended value.
General Information:
Conversion example of point code from 4-byte integer to IA5 format:·
•
•
ITU C7 point code (3 bits - 8bits - 3bits)
Tag value in integer format = 4114
Convert tag value in binary format = 1000000010010
Convert tag value in IA5 format = 10-00000010-010 (2-2-2)
ANSI SS7 point code (8 bits - 8 bits - 8 bits)
Tag value in integer format = 131586
Convert tag value in binary format = 100000001000000010
Convert tag value in IA5 format = 10-00000010-00000010 (2-2-2)
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-108
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Originating Point Code (Tag: 4036)
Table 1-91
Egress Originating Point Code
Name: Egress Originating Point Code
Description/Purpose: Holds the egress originating point code.
Format: BE Length in Octets: 4
Tag: 4036
Source: MDL
Data Value: The point code is in 4-byte integer format.
Extended Data Value: No extended value.
General Information:
Conversion example of point code from 4-byte integer to IA5 format:·
•
•
ITU C7 point code (3 bits - 8bits - 3bits)
Tag value in integer format = 4114
Convert tag value in binary format = 1000000010010
Convert tag value in IA5 format = 10-00000010-010 (2-2-2)
ANSI SS7 point code (8 bits - 8 bits - 8 bits)
Tag value in integer format = 131586
Convert tag value in binary format = 100000001000000010
Convert tag value in IA5 format = 10-00000010-00000010 (2-2-2)
MGC Release: Release 7.0 and later.
Egress Destination Point Code (Tag: 4037)
Table 1-92
Egress Destination Point Code Description Form
Name: Egress Destination Point Code
Tag: 4037
Source: MDL
Description/Purpose: Holds the egress destination point code.
Format: BE Length in Octets: 4
Data Value: The point code is in 4-byte integer format.
Extended Data Value: No extended value.
General Information:
Conversion example of point code from 4-byte integer to IA5 format:·
•
•
ITU C7 point code (3 bits - 8bits - 3bits)
Tag value in integer format = 4114
Convert tag value in binary format = 1000000010010
Convert tag value in IA5 format = 10-00000010-010 (2-2-2)
ANSI SS7 point code (8 bits - 8 bits - 8 bits)
Tag value in integer format = 131586
Convert tag value in binary format = 100000001000000010
Convert tag value in IA5 format = 10-00000010-00000010 (2-2-2)
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-109
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Ingress Media Gateway ID (Tag: 4038)
Table 1-93
Ingress Media Gateway ID Description Form
Name: Ingress Media Gateway ID
Tag: 4038
Source: MDL
Description/Purpose: Ingress media gateway ID (expressed in address).
Format: BE
Length in Octets: 2
Data Value: 16 bits of binary value.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Egress Media Gateway ID (Tag: 4039)
Table 1-94
Egress Media Gateway ID Description Form
Name: Egress Media Gateway ID
Tag: 4039
Source: MDL
Description/Purpose: Egress media gateway ID (expressed in address).
Format: BE
Length in Octets: 2
Data Value: 16 bits of binary value.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
TCAP Transaction ID (Tag: 4040)
Table 1-95
TCAP Transaction ID Description Form
Name: TCAP Transaction ID
Tag: 4040
Source: MDL
Description/Purpose: The TCAP transaction ID holds a unique identification number for each external request to an SCP,
an intelligent peripheral (IP), or some other database.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-110
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Transaction Start Time (Tag: 4041)
Table 1-96
Transaction Start Time Description Form
Name: Transaction Start Time
Tag: 4041
Source: MDL/Engine
Description/Purpose: The time at which the Cisco MGC sent an external request to an SCP, intelligent peripheral (IP), or
some other database.
Format: DT2
Length in Octets: 6
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Transaction End Time (Tag: 4042)
Table 1-97
Transaction End Time Description Form
Name: Transaction End Time
Tag: 4042
Source: MDL/Engine
Description/Purpose: The time at which the Cisco MGC received a response from an external request to an SCP, IP, or some
other database.
Format: DT2
Length in Octets: 6
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
TCAP Database ID (Tag: 4043)
Table 1-98
TCAP Database ID Description Form
Name: TCAP Database ID
Tag: 4043
Source: MDL/Engine
Description/Purpose: The external database identification number for the SCP, IP, or some other external database for which
a transaction was performed.
Format: BE
Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-111
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Announcement ID (Tag: 4044)
Table 1-99
Announcement ID Description Form
Name: Announcement ID
Tag: 4044
Source: MDL
Description/Purpose: Announcement ID value.
Format: BE
Length in Octets: 2
Data Value: An integer value to identify which announcement to play.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Route Selection Info (Tag: 4045) Retired
Table 1-100
Route Selection Info Description Form
Name: Route Selection Info
Tag: 4045
Source: MDL
Description/Purpose: Route index and the route ID value.
Format: BE
Length in Octets: 4
Data Value:
SubfieldLengthValue
Route Index2Route Index that is used to select a route
Route ID2Route ID selected
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later. This tag is retired as of Release 9.5(2).
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-112
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Ingress Packet Info (Tag: 4046) Restored
Table 1-101
Ingress Packet Info Description Form
Name: Ingress Packet Info
Tag: 4046
Source: MDL
Description/Purpose: Contains the packets sent, packets received, packets lost, octets sent, octets received, jitter, and
latency information (reserved 1 and 2) from the ingress gateway.
On Release 9.7(3), H.248 support is added. For an H.248 call, the subfield definitions are unchanged and the data is filled
with the statistics of Network Package (nt) and RTP Package (rtp) in H.248.
Format: BE
Length in Octets: 36
Data Value:
SubfieldLengthPosition Value
Packets sent41MGCP->DLCX or DLCX ack,P:PS=
Packets received45MGCP->DLCX or DLCX ack,P:PR=
Packets lost49MGCP->DLCX or DLCX ack,P:PL=
Octets sent413MGCP->DLCX or DLCX ack,P:OS=
Octets received417MGCP->DLCX or DLCX ack,P:OR=
Jitter421MGCP->DLCX or DLCX ack,P:JI=
Latency425MGCP->DLCX or DLCX ack,P:LA=
Reserved 1429
Reserved 2433
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 to 7.3 and Release 9.4(1) and up.
Note: This tag was retired in Release 7.4. It is restored as of Release 9.4(1).
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-113
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Packet Info (Tag: 4047) Restored
Table 1-102
Egress Packet Info Description Form
Name: Egress Packet Info
Tag: 4047
Source: MDL
Description/Purpose: Contains the packets sent, packets received, packets lost, octets sent, octets received, jitter, and
latency information (reserved 1 and 2) from the egress gateway.
On Release 9.7(3), H.248 support is added. For an H.248 call, the subfield definitions are unchanged and the data is filled
with the statistics of Network Package (nt) and RTP Package (rtp) in H.248.
Format: BE
Length in Octets: 36
Data Value:
SubfieldLengthPosition Value
Packets sent41MGCP->DLCX or DLCX ack,P:PS=
Packets received45MGCP->DLCX or DLCX ack,P:PR=
Packets lost49MGCP->DLCX or DLCX ack,P:PL=
Octets sent413MGCP->DLCX or DLCX ack,P:OS=
Octets received417MGCP->DLCX or DLCX ack,P:OR=
Jitter421MGCP->DLCX or DLCX ack,P:JI=
Latency425MGCP->DLCX or DLCX ack,P:LA=
Reserved 1429
Reserved 2433
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 to 7.3, and Release 9.4(1) and up.
Note: This tag was retired in Release 7.4. It is restored as of Release 9.4(1).
Directional Flag (Tag: 4048)
Table 1-103
Directional Flag Description Form
Name: Directional Flag
Tag: 4048
Source: MDL/Engine
Description/Purpose: Contains information that describes the role of the Cisco MGC when EISUP is involved.
Format: BE
Length in Octets: 1
Data Value:
0 = Intermediate Switch (E-ISUP to E-ISUP)
1 = Ingress Switch (^E-ISUP to E-ISUP)
2 = Egress Switch (E-ISUP to ^E-ISUP)
3 = Both (^E-ISUP to ^E-ISUP)
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-114
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Service Logic ID (Tag: 4049)
Table 1-104
Service Logic ID Description Form
Name: Service Logic ID
Tag: 4049
Source: MDL
Description/Purpose: This field value is used in an advanced intelligent network (AIN) environment. It records an
identification of service logic in the SCP that was used. The AMAslpID returns from the SCP hold the service logic ID
value.
Format: IA5
Length in Octets: 9
Data Value: 000000001 – 899999999
Extended Data Value: No extended value.
General Information: This field value implies that the mediation software (when configured to generate AMA) generates
Structure Code 220. (For more details please refer to Telcordia GR-2892-CORE Section 8.)
Note
This CDE is not applicable to INAP calls.
MGC Release: Release 7.0 and later.
AMA Line Number (Tag: 4050)
Table 1-105
AMA Line Number Description Form
Name: AMA Line Number
Tag: 4050
Source: MDL
Description/Purpose: This field value is used in an AIN environment. It is included in the Analyzed_Route message. It uses
an AIN digits format and contains the original called party ID, incoming terminating number, or ANI.
Format: IA5
Length in Octets: 15
Data Value: Up to a 12-digit line number and a 3-digit line number type.
Extended Data Value: No extended value.
General Information: This field value implies that the mediation software (when configured to generate AMA) generates
Structure Code 220 with AMALineNumber to be recorded in Module Code 307. (For more details, please refer to Telcordia
GR-2892-CORE Section 8.)
Note
The Analyzed_Route message allows up to two AMALineNumber parameters; therefore, the Cisco MGC can save
up to two AMA line numbers, and the mediation can generate two module Code 307s.
Note
This CDE is not applicable to INAP calls.
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-115
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
OOriginating Gateway Primary Select (Tag: 4052) Defined for Future Use
Table 1-106
Originating Gateway Primary Select Form
Name: Originating Gateway Primary Select Tag: 4052
Source: MDL/Engine
Description/Purpose:
Format: Binary
Length in Octets: 1
Data Value:
0 = False
1 = True
Extended Data Value: No extended value.
General Information:
MGC Release: Defined for Future Use
Terminating Gateway Primary Select (Tag: 4053) Defined for Future Use
Table 1-107
Terminating Gateway Primary Select Form
Name: Terminating Gateway Primary Select Tag: 4053
Source: MDL/Engine
Description/Purpose:
Format: Binary
Length in Octets: 1
Data Value:
0 = False
1 = True
Extended Data Value: No extended value.
General Information:
MGC Release: Defined for future use.
Redirecting Number (Tag: 4060)
Table 1-108
Redirecting Number Description Form
Name: Redirecting Number
Tag: 4060
Source: MDL/Engine
Description/Purpose: Stores the digits from Redirecting Number.
Format: IA5 Length in Octets: 1–96
Data Value: Character string containing the forwarded station’s address or subscriber number.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-116
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Scale Factor (Tag: 4062)
Table 1-109
Scale Factor Description Form
Name: Scale Factor
Tag: 4062
Source: MDL/Engine
Description/Purpose: Used for reporting Advice of Charge information.
Format: BE Length in Octets: 4
Data Value: The actual value for the scale factor is given by 10^x, where x is the value of the scale factor. The coding of scale
factor is as follows; all other values are spare:
— (249) –7
— (250) –6
— (251) –5
— (252) –4
— (253) –3
— (254) –2
— (255) –1
0.0000001
0.000001
0.00001
0.0001
0.001
0.01
0.1
—
—
—
—
0
1
2
3
1
10
100
1000
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9 and later.
Test Line Indicator (Tag: 4063)
Table 1-110
Test Line Indicator Description Form
Name: Test Line Indicator
Tag: 4063
Source: MDL/Engine
Description/Purpose: The test line indicator is used for reporting the type of test line.
Format: BE Length in Octets: 4
Data Value: Valid values for the TestLineType integer are:
TYPE_100 = 0
TYPE_102 = 1
TYPE_105 = 2
TYPE_108 = 3
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-117
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Redirection Number (Tag: 4065)
Table 1-111
Ingress SigPath ID Description Form
Name: Redirection Number
Tag: 4065
Source: MDL
Description/Purpose: This tag contains the digits of the new number when the PGW redirects a call.
Format: IA5
Length in Octets: 1-96
Data Value: Redirection number digits
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.7 and later.
Ingress SigPath ID (Tag: 4066)
Table 1-112
Ingress SigPath ID Description Form
Name: Ingress SigPath ID
Tag: 4066
Source: MDL/Engine
Description/Purpose: The ingress SigPath ID is used to associate incoming bearer channels with signaling services, such
as a destination point code (DPC) in SS7.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Ingress Span ID (Tag: 4067)
Table 1-113
Ingress Span ID Description Form
Name: Ingress Span ID
Tag: 4067
Source: MDL/Engine
Description/Purpose: The ingress Span ID is used for incoming PRI bearer channels. A span is a grouping of bearer
channels.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-118
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Ingress BearChan ID (Tag: 4068)
Table 1-114
Ingress BearChan ID Description Form
Name: Ingress BearChan ID
Tag: 4068
Source: MDL/Engine
Description/Purpose: The ingress BearChan ID is used for incoming bearer channels.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Ingress Protocol ID (Tag: 4069)
Table 1-115
Ingress Protocol ID Description Form
Name: Ingress Protocol ID
Tag: 4069
Source: MDL/Engine
Description/Purpose: The ingress Protocol ID is determined from MDL and is used in measurements and billing.
On Release 9.7(3), for the H.248 Protocol feature, new protocol type: “10=H.248” is added to the definition.
Format: BE
Length in Octets: 1
Data Value:
0 = ISDN PRI
1 = C7
2 = DPNSS
3 = CAS
4 = ASN
5 = Unknown
6 = EISUP
7 = H.323
8 = SIP
9 = MGCP
Binary big-endian
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-119
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress SigPath ID (Tag: 4070)
Table 1-116
Egress SigPath ID Description Form
Name: Egress SigPath ID
Tag: 4070
Source: MDL/Engine
Description/Purpose: The egress SigPath ID is used to associate outgoing bearer channels with signaling services, such as
a destination point code (DPC) in SS7.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Egress Span ID (Tag: 4071)
Table 1-117
Egress Span ID Description Form
Name: Egress Span ID
Tag: 4071
Source: MDL/Engine
Description/Purpose: The egress Span ID is used for outgoing PRI bearer channels. A span is a grouping of bearer channels.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Egress BearChan ID (Tag: 4072)
Table 1-118
Egress BearChan ID Description Form
Name: Egress BearChan ID
Tag: 4072
Source: MDL/Engine
Description/Purpose: The egress BearChan ID is used for outgoing bearer channels.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-120
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Protocol ID (Tag: 4073)
Table 1-119
Egress Protocol ID Description Form
Name: Egress Protocol ID
Tag: 4073
Source: MDL/Engine
Description/Purpose: The egress Protocol ID is determined from MDL and is used in measurements and billing.
On Release 9.7(3), for the H.248 Protocol feature, new protocol type: “10=H.248” is added to the definition.
Format: BE
Length in Octets: 1
Data Value:
0 = ISDN PRI
1 = C7
2 = DPNSS
3 = CAS
4 = ASN
5 = Unknown
6 = EISUP
7 = H.323
8 = SIP
9 = MGCP
Binary big-endian
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Maintenance SigPath ID (Tag: 4074)
Table 1-120
Maintenance SigPath ID Description Form
Name: Maintenance SigPath ID
Tag: 4074
Source: MDL/Engine
Description/Purpose: The maintenance SigPath ID is used to associate maintenance bearer channels with signaling services,
such as a destination point code (DPC) in SS7.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-121
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Maintenance Span ID (Tag: 4075)
Table 1-121
Maintenance Span ID Description Form
Name: Maintenance Span ID
Tag: 4075
Source: MDL/Engine
Description/Purpose: The maintenance Span ID is used for maintenance PRI bearer channels. A span is a grouping of bearer
channels.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Maintenance BearChan ID (Tag: 4076)
Table 1-122
Maintenance BearChan ID Description Form
Name: Maintenance BearChan ID
Tag: 4076
Source: MDL/Engine
Description/Purpose: The maintenance BearChan ID is used for maintenance bearer channels.
Format: BE
Length in Octets: 4
Data Value: 32 bits of binary value
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7 and later.
Maintenance Circuits Count (Tag: 4077)
Maintenance Circuits Count Description Form
Name: Maintenance Circuits Count
Tag: 4077
Source: MDL/Engine
Description/Purpose: The maintenance circuits count is the number of circuits in a maintenance event reported in
CDB 1070.
Format: BE
Length in Octets: 4
Data Value: Counting is zero based, so add 1 to any result returned in this tag for the actual circuit count.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.3(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-122
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Charge Band Number (Tag: 4078)
Table 1-123
Charge Band Number Description Form
Name: Charge Band Number
Tag: 4078
Source: MDL/Engine
Description/Purpose: Used for reporting Advice of Charge information.
Format: BE Length in Octets: 1
Data Value: Integer containing the Charge Band Number: Range: 0-255.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.3(1) and later.
Furnish Charging Information (Tag: 4079)
Table 1-124
Furnish Charging Information Description Form
Name: Furnish Charging Information
Tag: 4079
Source: MDL
Description/Purpose: Returned by the SCP during an IN Prepaid Service call dialog. Contains unspecified charge data to
be written to the CDR.
Format: IA5
Length in Octets: Variable
Data Value: Unspecified.
Extended Data Value: No extended value.
General Information: Assigned by SCP and transparently passed to CDR
MGC Release: Release 9.3(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-123
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Original Called Number (Tag: 4080)
Table 1-125
Original Called Number Description Form
Name: Original Called Number
Tag: 4080
Source: MDL
Description/Purpose: This tag contains the digits from the original called party number.
Format: IA5 Length in Octets: 1-96
Data Value: The digits of the original called party number.
Extended Data Value: No extended value.
General Information: The following are conditions that could have Original Called Number:
•
•
Original called number parameter could be received in the IAM message if the call is redirected before for SS7 calls.
A distant end TDM switch sends a Release message back to the MGC over SS7 containing a Cause parameter or
Redirection Information parameter, Redirection Number parameter, and possibly a Redirection Number Restriction
parameter.
The actual cause value contained indicates that re-direction is required and Cause analysis directs this. If the call is
redirected and there is no original called party number, then the called party number is mapped to the original called party
number.
MGC Release: Release 9.3(1) and later.
T.38 Fax Call (Tag: 4081)
Table 1-126
T.38 Fax Call Description Form
Name: T.38 Fax Call
Tag: 4081
Source: MDL
Description/Purpose: Indicates that the call was a Fax call negotiated using T.38.
Format: IA5
Length in Octets: 1
Data Value:
0 = No Fax information available
1 = Call Agent negotiated T.38 Fax call
Extended Data Value: No extended value.
General Information: The data for this CDR is assigned by SCP and transparently passed to CDR.
MGC Release: Release 9.3(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-124
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Charge Unit Number (Tag: 4082)
Table 1-127
Charge Unit Number Description Form
Name: Charge Unit Number
Tag: 4082
Source: MDL
Description/Purpose: Used for reporting Advice of Charge information.
Format: BE
Length in Octets: 1
Data Value:
Comprised of an integer containing the Charge Unit Number, provisioned as part of the Dial Plan provisioning
ANSI/ITU Variations: None
Valid Range: 0-255
Extended Data Value: No extended value.
General Information: The data for this CDR is assigned by SCP and transparently passed to CDR.
MGC Release: Release 9.3(2) and later.
Charge Indicator (Tag: 4083)
Table 1-128
Charge Indicator Description Form
Name: Charge Indicator
Tag: 4083
Source: MDL
Description/Purpose: Allows the carrier to determine whether certain calls need to be billed.
Format: BE
Length in Octets: 1
Data Value:
Charge Indicator information is 2 bit and is defined as follows:
01
10
00
No Charge
Charge
No Indication
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-125
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Outgoing Calling Party Number (Tag: 4084)
Table 1-129
Outgoing Calling Party Number Description Form
Name: Outgoing Calling Party Number
Tag: 4084
Source: MDL
Description/Purpose: The Calling Party Number being sent out on line by the Cisco MGC is recorded in this tag. This value
may be different from the received Calling Party Number. The received Calling Party Number may be modified either
because of Generic Number or in Generic Analysis.
Format:IA5
Length in Octets: 1 to 96
Data Value: It holds the Outgoing Calling Party Number.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
MCID Request Indicator (Tag: 4085)
Table 1-130
MCID Request Indicator Description Form
Name: MCID Request Indicator
Tag: 4085
Source: MDL
Description/Purpose: Allows the carrier to determine whether MCID is requested or not.
Format: BE
Length in Octets: 1
Data Value:
MCID Request Indicator information is 1 bit and is defined as follows:
0
1
MCID not requested
MCID requested
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-126
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
MCID Response Indicator (Tag: 4086)
Table 1-131
MCID Response Indicator Description Form
Name: MCID Response Indicator
Tag: 4086
Source: MDL
Description/Purpose: Allows the carrier to determine whether MCID is included or not.
Format: BE
Length in Octets: 1
Data Value:
MCID Response Indicator information is 1 bit and is defined as follows:
0
1
MCID not included
MCID included
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Ingress MGCP DLCX Return Code (Tag: 4087)
Table 1-132
Ingress MGCP DLCX Return Code Description Form
Name: Ingress MGCP DLCX Return Code Tag: 4087
Source: MDL
Description/Purpose: Indication of MGCP DLCX (Delete Connection) return code value on the ingress gateway.
On Release 9.7(3), the H.248 Protocol feature is added. If an H.248 gateway is engaged on the ingress side, this tag is not
logged in to CDR.
Format: BE
Length in Octets: 1
Data Value: Return code value returned by the associated media gateway.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Egress MGCP DLCX Return Code (Tag: 4088)
Table 1-133
Egress MGCP DLCX Return Code Description Form
Name: Egress MGCP DLCX Return Code Tag: 4088
Source: MDL
Description/Purpose: Indication of MGCP DLCX (Delete Connection) return code value from the egress gateway.
On Release 9.7(3), the H.248 Protocol feature is added. For the H.248 gateway, this tag is not logged in to CDR.
Format: BE
Length in Octets: 1
Data Value: Return code value returned by the associated media gateway.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-127
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Network Translated Address Indicator (Tag: 4089)
Table 1-134
Network Translated Address Indicator Description Form
Name:
Tag: 4089
Source: MDL
Network Translated Address Indicator
Description/Purpose: Information sent in the forward direction to indicate whether network translation of the called address
has occurred. This indicator is specific to BTNUP, UK IUP, and UK ISUP. This allows you to determine whether a number
has been translated. An example of this would be a 1-900 provider. If the NTA has not occurred, the customer would know
that the calling party is not paying for the call.
Format: BE
Length in Octets: 1
Data Value:
Network Translated Address Indicator information is 1 bit and is defined as follows:
0
1
No Indication
Network Translated Address Indication
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Reservation Request Accepted (Tag: 4090)
Table 1-135
Reservation Request Accepted Description Form
Name:
Tag: 4090
Source: MDL
Reservation Request Accepted
Description/Purpose: This tag is present if the call was made using the Resource Reservation Protocol on the bearer.
Format: BE
Length in Octets: 1
Data Value:
0 = No RSVP was present
1 = RSVP was present in the call
2 = RSVP was present in the call, but call torn down when res/rl received
ANSI/ITU Variations: None
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-128
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Reservation Request Error Count (Tag: 4091)
Table 1-136
Reservation Request Error Count Description Form
Name:
Tag: 4091
Source: MDL
Reservation Request Error Count
Description/Purpose: This tag is present if the Resource Reservation Lost event was received during a call. It will be a count
of the number of times the event occurred during the call.
Format: BE
Length in Octets: 1
Data Value:
Count of the number of times the Resource Reservation Error event was received during a call.
ANSI/ITU Variations: None
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
ATM Ingress Configured Profile (Tag: 4092)
Table 1-137
ATM Ingress Configured Profile Description Form
Name:
Tag: 4092
Source: MDL
ATM Ingress Configured Profile
Description/Purpose: This tag is present if an ATM profile was configured based on Service Level Agreement (SLA) for
Ingress call leg.
Format: IA5
Length in Octets: 1-16
Data Value:
ITU 1
ITU 2
ITU 3
ITU 7
ITU 8
ITU 12
Custom 100
Custom 101
Custom 110
Custom 200
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-129
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
ATM Egress Configured Profile (Tag: 4093)
Table 1-138
ATM Egress Configured Profile Description Form
Name:
Tag: 4093
Source: MDL
ATM Egress Configured Profile
Description/Purpose: This tag is present if an ATM profile was configured based on Service Level Agreement (SLA) for
Egress call leg.
Format: IA5
Length in Octets: 1-16
Data Value:
ITU 1
ITU 2
ITU 3
ITU 7
ITU 8
ITU 12
Custom 100
Custom 101
Custom 110
Custom 200
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-130
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
ATM Negotiated Profile (Tag: 4094)
Table 1-139
ATM Negotiated Profile Description Form
Name:
Tag: 4094
Source: MDL
ATM Negotiated Profile
Description/Purpose: This tag is present if an ATM profile was negotiated based on Service Level Agreement (SLA).
Format: IA5
Length in Octets: 1-16
Data Value:
ITU 1
ITU 2
ITU 3
ITU 7
ITU 8
ITU 12
Custom 100
Custom 101
Custom 110
Custom 200
ANSI/ITU Variations: None
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Route List Name (Tag: 4095)
Table 1-140
Route List Name Description Form
Name: Route List Name
Tag: 4095
Source: Engine
Description/Purpose: Route List Name being used for the call.
Format:IA5
Length in Octets: 1 to 20
Data Value: ASCII name of the Route List being used.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-131
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Route Name (Tag: 4096)
Table 1-141
Route Name Description Form
Name: Route Name
Tag: 4096
Source: Engine
Description/Purpose: Route Name being used for the call.
Format:IA5
Length in Octets: 1 to 20
Data Value: ASCII name of the route being used.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
MGCP Script Response String (Tag: 4097)
Table 1-142
MGCP Script Response String Description Form
Name:
Tag: 4097
Source: MDL
MGCP Script Response String
Description/Purpose: For MGCP Script hand-off calls, this tag records the Notification response string, if any, returned in
the O: parameter of the MGCP NTFY message. If this call did not receive a MGCP NTFY message, this tag is not logged.
On Release 9.7(3), the H.248 Protocol feature is supported. As MGCP scripting is not ported to H.248, H.248 never
generate this CDB.
Format: IA5
Length in Octets: maximum of 128
Data Value:
Contains the response string as obtained from the media gateway, in the MGCP NTFY message, including the event
indicators oc or of.
ANSI/ITU Variations: None.
Other variations: None.
Values: n/a
Examples:
oc(Call completed.)
oc(Authentication failed)
of()
of
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-132
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Originating Leg DSP Statistics (Tag: 4098)
Table 1-143
Originating Leg DSP Statistics Description Form
Name: Originating Leg DSP Statistics
Tag: 4098
Source: Engine
Description/Purpose: Provides DSP statistics for the originating leg of the call.
On Release 9.7(3), the H.248 Protocol feature is added. Because for H.248 DSP statistics in CDR are not supported, this
tag is not logged in to CDR for the H.248 leg.
Format: IA5
Length in Octets: 280 through 794
Data Value:
An example of the statistics generated by the media gateway appears below:
OrigDSPstats...: DSP/TX: PK=data1, SG=data2, NS= data3, DU= data4, VO=,
DSP/RX: VO= , SG= , CF= , RX= , BS= , BP= , LP= , EP= ,
DSP/PD: CU= , MI= , MA= , CO= , IJ= ,
DSP/PE: PC= , IC= , SC= , RM= , BO= , EE= ,
DSP/LE: TP= , TX= , RP= , RM= , BN= , ER= , AC= , TA= , RA= ,
DSP/ER: RD= , TD= , RC= , TC= ,
DSP/IC: IC= ,.
In Release 9.6, the statistics are enhanced to support the DSP Voice Quality Statistics in DLCX Messages feature in Cisco
IOS Release 12.4(4)T. The DSP Voice Quality Statistics feature introduces a priority setting on the media gateway that
allows control of the impact of statistic generation. There are two priority values: 1, which limits the statistics generated
by the media gateway, and 2, which enables all statistics to be generated.
An example of the appearance of the statistics generated when the media gateway is set to priority 1 appears below.
OrigDSPstats…..:DSP/TX: PK=, SG=, NS=, DU=, VO=,
DSP/RX: PK=, SG=, CF=, RX=, VO=, BS=, BP=, LP=, EP=,
DSP/PD: CU=, MI=, MA=, CO=, IJ=,
DSP/LE: TP=, TX=, RP=, RM=, BN=, ER=, AC=,
DSP/EC: CI=, FM=, FP=, VS=, GT=, GR=, JD=, JN=, JM=, JX=,
DSP/CS: CR=, AV=, MX=, CT=, TT=, OK=, CS=, SC=, TS=, DC=,
DSP/DL: RT=, ED=
An example of the appearance of the statistics generated when the media gateway is set to priority 2 appears below.
OrigDSPstats…..:DSP/TX: PK=, SG=, NS=, DU=, VO=,
DSP/RX: PK=, SG=, CF=, RX=, VO=, BS=, BP=, LP=, EP=,
DSP/PD: CU=, MI=, MA=, CO=, IJ=,
DSP/PE: PC=, IC=, SC=, RM=, BO=, EE=,
DSP/LE: TP=, TX=, RP=, RM=, BN=, ER=, AC=,
DSP/ER: RD=, TD=, RC=, TC=,
DSP/IC: IC=,
DSP/EC: CI=, FM=, FP=, VS=, GT=, GR=, JD=, JN=, JM=, JX=,
DSP/KF: KF=, AV=, MI=, BS=, NB=, FL=, NW=, VR=,
DSP/CS: CR=, AV=, MX=, CT=, TT=, OK=, CS=, SC=, TS=, DC=,
DSP/RF: ML=, MC=, R1=, R2=, IF=, ID=, IE=, BL=, R0=, VR=,
DSP/UC: U1=, U2=, T1=, T2=,
DSP/DL: RT=, ED=
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-133
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-143
Originating Leg DSP Statistics Description Form (continued)
Extended Data Value: No extended value.
General Information: This CDE is populated when an originating endpoint is controlled by the Cisco MGC software
through the MGCP protocol and the associated MGCP media gateway is enabled to send DSP statistics to the Cisco MGC.
Information on the configuring DSP voice quality statistics on the media gateway and definitions for the various fields used
MGC Release: Release 9.4(1) and later.
Support of the DSP voice quality statistics is added in Release 9.6(1), patch CSCOnn026.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-134
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Terminating Leg DSP Statistics (Tag: 4099)
Table 1-144
Terminating Leg DSP Statistics Description Form
Name: Terminating Leg DSP Statistics
Tag: 4099
Source: Engine
Description/Purpose: Provides DSP statistics for the terminating leg of the call.
On Release 9.7(3), the H.248 Protocol feature is added. Because for H.248 DSP statistics in CDR are not supported, this
tag is not logged in to CDR for the H.248 leg.
Format: IA5
Length in Octets: 280 through 794
Data Value:
TermDSPstats.....: DSP/TX: PK=data1, SG=data2, NS= data3, DU= data4, VO=,
DSP/RX: VO= , SG= , CF= , RX= , BS= , BP= , LP= , EP= ,
DSP/PD: CU= , MI= , MA= , CO= , IJ= ,
DSP/PE: PC= , IC= , SC= , RM= , BO= , EE= ,
DSP/LE: TP= , TX= , RP= , RM= , BN= , ER= , AC= , TA= , RA= ,
DSP/ER: RD= , TD= , RC= , TC= ,DSP/IC: IC= ,.
In Release 9.6, the statistics are enhanced to support the DSP Voice Quality Statistics in DLCX Messages feature in Cisco
IOS Release 12.4(4)T. The DSP Voice Quality Statistics feature introduces a priority setting on the media gateway that
allows control of the impact of statistic generation. There are two priority values: 1, which limits the statistics generated
by the media gateway, and 2, which enables all statistics to be generated.
An example of the appearance of the statistics generated when the media gateway is set to priority 1 appears below.
TermDSPstats…..:DSP/TX: PK=, SG=, NS=, DU=, VO=,
DSP/RX: PK=, SG=, CF=, RX=, VO=, BS=, BP=, LP=, EP=,
DSP/PD: CU=, MI=, MA=, CO=, IJ=,
DSP/LE: TP=, TX=, RP=, RM=, BN=, ER=, AC=,
DSP/EC: CI=, FM=, FP=, VS=, GT=, GR=, JD=, JN=, JM=, JX=,
DSP/CS: CR=, AV=, MX=, CT=, TT=, OK=, CS=, SC=, TS=, DC=,
DSP/DL: RT=, ED=
An example of the appearance of the statistics generated when the media gateway is set to priority 2 appears below.
TermDSPstats…..:DSP/TX: PK=, SG=, NS=, DU=, VO=,
DSP/RX: PK=, SG=, CF=, RX=, VO=, BS=, BP=, LP=, EP=,
DSP/PD: CU=, MI=, MA=, CO=, IJ=,
DSP/PE: PC=, IC=, SC=, RM=, BO=, EE=,
DSP/LE: TP=, TX=, RP=, RM=, BN=, ER=, AC=,
DSP/ER: RD=, TD=, RC=, TC=,
DSP/IC: IC=,
DSP/EC: CI=, FM=, FP=, VS=, GT=, GR=, JD=, JN=, JM=, JX=,
DSP/KF: KF=, AV=, MI=, BS=, NB=, FL=, NW=, VR=,
DSP/CS: CR=, AV=, MX=, CT=, TT=, OK=, CS=, SC=, TS=, DC=,
DSP/RF: ML=, MC=, R1=, R2=, IF=, ID=, IE=, BL=, R0=, VR=,
DSP/UC: U1=, U2=, T1=, T2=,
DSP/DL: RT=, ED=
Extended Data Value: No extended value.
General Information: This CDE is populated when a terminating endpoint is controlled by the Cisco MGC software
through the MGCP protocol and the associated MGCP media gateway is enabled to send DSP statistics to the Cisco MGC.
Information on the configuring DSP voice quality statistics on the media gateway and definitions for the various fields used
MGC Release: Release 9.4(1) and later.
Support of the DSP voice quality statistics is added in Release 9.6(1), patch CSCOnn026.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-135
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Originating Remote SIP Host (Tag: 4201)
Table 1-145
Originating Remote SIP Host Description Form
Name: Originating Remote SIP Host
Tag: 4201
Source: MDL/Engine
Description/Purpose: Formerly named as Ingress SIP URL. Contains the remote host for the originating side of a
SIP-originated call (this tag is present only if SIP appears on the originating side of the call). In a simple call, this host is
taken out of the From header, but if a P-Asserted or Remote Party ID header is received and has influenced the calling line
information, then the host is taken from the header that provides the resultant calling line information.
Format: IA5
Length in Octets: 1 to 256
Data Value: URL
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9 and later.
Originating Local SIP Host (Tag: 4202)
Table 1-146
Originating Local SIP Host Description Form
Name: Originating Local SIP Host
Tag: 4202
Source: MDL/Engine
Description/Purpose: Formerly named as Egress SIP URL. Contains the local host (the To Host received in a REQUEST
on the originating side) of the originating side of a SIP call. This tag is present only if the originating side of the call is SIP.
Format: IA5
Length in Octets: 1 to 256
Data Value: URL
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9 and later.
SIP Call ID (Tag: 4203)
Table 1-147
SIP Call ID Description Form
Name: SIP Call ID
Tag: 4203
Source: MDL/Engine
Description/Purpose: Unique SIP call ID used to identify the SIP call leg. Depending on the PSTN-to-SIP or SIP-to-PSTN
call, the SIP call ID appears in the originating or terminating call side.
Format: IA5
Length in Octets: 1 to 256
Data Value: Generated by call originator.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-136
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Source IP Address (Tag: 4204)
Table 1-148
Source IP Address Description Form
Name: Source IP Address
Tag: 4204
Source: MDL
Description/Purpose: Identifies the source that sends the call setup message in incoming SIP and H.323 calls.
Format: IA5 (string) Length in Octets: 1 to 23
Data Value: IPV4 format. Example: 10.1.22.115.
Extended Data Value: No extended value.
General Information: The source IP address is used to look up a dial plan in the IP Address Table if the trunk group property,
EnableIPScreening, is set to 1.
MGC Release: Release 9.4(1) and later.
Ingress Media Device Address (Tag: 4205)
Table 1-149
Ingress Media Device Address Description Form
Name: Ingress Media Device Address
Tag: 4205
Source: MDL
Description/Purpose: Identifies the IP address of the originating RTP end point. This is parsed from the SDP from SIP,
MGCP, or EISUP (HSI).
Format: IA5 (string)
Length in Octets: 1 to 256
Data Value: IPV4 format or FQDN. Examples: 10.1.22.115, sp-46-39-gateway.customer.com.
Extended Data Value: No extended value.
General Information: If the ingress media device address is an IP address, it is used to look up a dial plan in the IP Address
Table if the trunk group properties, EnableIPScreening and SipIPSource, are set to 1. If the call is originated in the H.323
domain as a Slow Start call, this information is not present in the 1010 CDB. If the call is originated in the H.323 domain
as a Slow Start call and a switchover operation is performed on the Cisco PGW 2200, this information is not captured in
any CDB.
MGC Release: Release 9.4(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-137
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Egress Media Device Address (Tag: 4206)
Table 1-150
Egress Media Device Address Description Form
Name: Engress Media Device Address
Tag: 4206
Source: MDL
Description/Purpose: Identifies the IP address of the terminating RTP end point. This is parsed from the SDP from SIP,
MGCP, or EISUP (HSI).
Format: IA5 (string)
Length in Octets: 1 to 256
Data Value: IPV4 format or FQDN. Examples: 10.1.22.115, sp-46-39-gateway.customer.com.
Extended Data Value: No extended value.
General Information: If the egress media device address is an IP address, it is used to look up a dial plan in the IP Address
Table if the trunk group properties, EnableIPScreening and SipIPSource, are set to 1. If the call is terminated in the H.323
domain as a Slow Start call, this information is not present in the 1010 CDB. If the call is terminated in the H.323 domain
as a Slow Start call and a switchover operation is performed on the Cisco PGW 2200, this information is not captured in
any CDB.
MGC Release: Release 9.4(1) and later.
Initial Codec (Tag: 4207)
Table 1-151
Initial Codec Description Form
Name: Initial Codec
Tag: 4207
Source: MDL
Description/Purpose: Identifies the initial codec used for the connection (the RTP stream). This is parsed from the SDP
from SIP or MGCP.
Format: IA5 (string)
Length in Octets: 1 to 12
Data Value: String. Example: PCMU
If the Cisco PGW 2200 cannot determine the initial codec used for a call, it is set to UNKNOWN
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.4(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-138
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Final Codec (Tag: 4208)
Table 1-152
Final Codec Description Form
Name: Final Codec
Tag: 4208
Source: MDL
Description/Purpose: Identifies the final codec used for the connection (the RTP stream). This is parsed from the SDP from
SIP or MGCP.
Format: IA5 (string)
Length in Octets: 1 to 12
Data Value: String. Example: PCMU
If the Cisco PGW 2200 cannot determine the final codec used for a call, it is set to UNKNOWN
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.4(1) and later.
Ingress Media Device Port (Tag: 4209)
Table 1-153
Ingress Media Device Port Description Form
Name: Ingress Media Device Port
Tag: 4209
Source: MDL
Description/Purpose: Identifies the ingress RTP port involved in the connection.
Format: IA5 (string)
Length in Octets: 1 to 6
Data Value: String. Example: 66218
Extended Data Value: No extended value.
General Information: If the call is originated in the H.323 domain as a Slow Start call, this information is not present in the
1010 CDB. If the call is originated in the H.323 domain as a Slow Start call and a switchover operation is performed on the
Cisco PGW 2200, this information is not captured in any CDB.
MGC Release: Release 9.4(1) and later.
Egress Media Device Port (Tag: 4210)
Table 1-154
Egress Media Device Port Description Form
Name: Engress Media Device Port
Tag: 4210
Source: MDL
Description/Purpose: Identifies the egress RTP port involved in the connection.
Format: IA5 (string)
Length in Octets: 1 to 6
Data Value: String. Examples: 1024, 58890.
Extended Data Value: No extended value.
General Information: If the call is terminated in the H.323 domain as a Slow Start call, this information is not present in
the 1010 CDB. If the call is terminated in the H.323 domain as a Slow Start call and a switchover operation is performed
on the Cisco PGW 2200, this information is not captured in any CDB.
MGC Release: Release 9.4(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-139
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Originating VPN ID (Tag: 4211)
Table 1-155
Originating VPN ID Description Form
Name: Originating VPN ID
Tag: 4211
Source: MDL
Description/Purpose: Identifies the VPN customer ID associated with the incoming trunk group or signaling service. It is
used for feature transparency with access protocols DPNSS and QSIG.
Format: IA5
Length in Octets: 8
Data Value: Alphanumeric string. It is associated with DPNSS and QSIG trunk groups. Example: BTFNET1
Extended Data Value: No extended value.
General Information: The inclusion of this tag is based upon the presence on a VPN ID associated with the incoming trunk
group.
Note: If the incoming trunk group is EISUP, the VPN ID of the incoming trunk group of the remote Cisco PGW 2200 is
used (if present).
MGC Release: Release 9.4(1) and later.
Terminating VPN ID (Tag: 4212)
Table 1-156
Terminating VPN ID Description Form
Name: Terminating VPN ID
Tag: 4212
Source: MDL
Description/Purpose: Identifies the VPN customer ID associated with the outgoing trunk group or signaling service. It is
used for feature transparency with access protocols DPNSS and QSIG.
Format: IA5
Length in Octets: 8
Data Value: Alphanumeric string. It is associated with DPNSS and QSIG trunk groups. Example: BTFNET1
Extended Data Value: No extended value.
General Information: The inclusion of this tag is based upon the presence on a VPN ID associated with the outgoing trunk
group.
Note: If the outgoing trunk group is EISUP, the VPN ID of the outgoing trunk group of the remote Cisco PGW 2200 is used
(if present).
MGC Release: Release 9.4(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-140
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Meter Pulses Received (Tag: 4213)
Table 1-157
Meter Pulses Received Description Form
Name: Meter Pulses Received
Tag: 4213
Source: MDL
Description/Purpose: Contains the total number of meter pulses received at the terminating side of the call.
Format: BE Length in Octets: 4
Data Value: Integer value in the range: 0 to 232-1
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Meter Pulses Sent (Tag: 4214)
Table 1-158
Meter Pulses Sent Description Form
Name: Meter Pulses Sent
Description/Purpose: Contains the total number of meter pulses sent to the originating side of the call.
Format: BE Length in Octets: 4
Tag: 4214
Source: MDL
Data Value: Integer value in the range: 0 to 232-1
Extended Data Value: No extended value.
General Information: The total pulses comprise those meter pulses generated internally and those transitted by the MGC.
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-141
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Charge Tariff Info (Tag: 4215)
Table 1-159
Charge Tariff Info Description Form
Name: Charge Tariff Info
Tag: 4215
Source: MDL
Description/Purpose: Contains Charging Tariff Information that has been sent or received in MPM messages. It comprises
the following data items:
•
•
•
tariff type sent
tariff type received
tariff id (timestamped) – may be repeated (up to 11 occurrences).
Format: BE
Length in Octets: 8, 14, 20, 26, 32, 38, 44, 50, 56, 62, or 68
Data Value:
Octet 1: integer value, range of 0-15 (tariff type sent)
Octet 2: integer value range of 0-15 (tariff type received)
Octets 3-4: integer value range of 0-512 (tariff id)
Octets 5-8: Time in UNIX format (timestamp associated with tariff id in octets 3-4)
Extended Data Value: No extended value.
General Information: Octets 3-8 may be repeated up to 11 times to allow for up to 11 tariff changes during the call.
Timestamps in octets 5-8 is in Unix format (as CDB Timepoint tag 4001).
MGC Release: Release 9.5(2) and later.
Advice of Charge Indicator (Tag: 4216)
Table 1-160
Advice of Charge Indicator Description Form
Name: Advice of Charge Indicator
Tag: 4216
Source: MDL
Description/Purpose: Used to record the status of the AOC field of the charging information sent in MPM messages, either
charge or advice of charge.
Format: BE
Length in Octets: 1
Data Value:
0 = Charge Information
1 = Advice Of Charge Only
Extended Data Value: No extended value.
General Information: This tag is a record of what was contained in the AOC indicator field of the MPM messages sent,
based on information obtained from either the meter pulse tariff table or received messages.
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-142
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Short Call Indicator (Tag: 4217)
Table 1-161
Short Call Indicator Description Form
Name: Short Call Indicator
Tag: 4217
Source: MDL
Description/Purpose: Used to indicate that a call was a short duration call.
Format: BE
Length in Octets: 1
Data Value: 1 = Short Call.
Extended Data Value: No extended value.
General Information: The actual period for the timer used to identify short duration calls is configurable between 1 and 30
seconds. This tag is only added to the CDB if the length of the call falls within the defined timeframe.
MGC Release: Release 9.5(2) and later.
Charge Limit Exceeded (Tag: 4218)
Table 1-162
Charge Limit Exceeded Description Form
Name: Charge Limit Exceeded
Tag: 4218
Source: MDL
Description/Purpose: Indicates that a call has exceeded the maximum duration permitted and has been cleared.
Format: BE
Length in Octets: 1
Data Value: 1 = Charge Limit Exceeded
Extended Data Value: No extended value.
General Information: For calls involving charging there is a maximum call duration timer maintained by the CDR manager.
If this timer expires, the call is cleared and Charge Limit Exceeded is recorded in this tag. The value used for the timer is
obtained from the tariff table or the ApplyCharging SCP procedure. This tag is only added to the CDB if the charge limit
is exceeded.
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-143
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Call Recovered Indication (Tag: 4219)
Table 1-163
Call Recovered Indication Description Form
Name: Call Recovered Indication
Tag: 4219
Source: MDL
Description/Purpose: Indicates that the call was recovered by the standby MGC host following an automatic switchover and
may have been released.
Format: BE
Length in Octets: 1
Data Value:
1 = Call Recovered
2 = Call Recovered and Released
Extended Data Value: No extended value.
General Information: Non-IN calls are recovered by the standby MGC host and continue normally following an automatic
switchover. IN Calls are recovered by the standby MGC host but are then released gracefully. This tag is used to record
either of these events. This tag is not included in the CDB for normal calls (that is, not recovered).
MGC Release: Release 9.5(2) and later.
Partial Calling Line Identity (Tag: 4220)
Table 1-164
Partial Calling Line Identity Description Form
Name: Partial Calling Line Identity (PCLI) Tag: 4220
Source: MDL
Description/Purpose: The Partial Calling Line Identity, being sent out on-line by the MGC, is recorded in this tag. This
value is generated by MGC in case CLI information is not received from the incoming call.
Format: Hexidecimal
Length in Octets: 9
Data Value:
It holds the Partial CLI parameter content, which has the following format:
Type of Switch (0-99)
PNO Identity (0-999)
Switch Number(0-999)
For bilateral agreement
For bilateral agreement
For bilateral agreement
For bilateral agreement
For bilateral agreement
The “For bilateral agreement” octets contain either the IP address or the trunk group and member of the incoming call.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-144
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Service Activation (Tag: 4221)
Table 1-165
Service Activation Description Form
Name: Service Activation
Tag: 4221
Source: MDL
Description/Purpose: Allows the user to determine which supplementary services have been invoked by the user or MGC.
Format: BE
Length in Octets: 1
Data Value:
Service Activation information is 1 Octet and is defined as follows:
AOC – S : 1
AOC – D: 2
AOC – E: 3
AOC – S and AOC - D: 4
AOC – S and AOC - E: 5
AOC – D and AOC – E: 6
AOC – S, AOC – D and AOC – E : 7
Call Back Request: 8 (added in Release 9.6(1))
Call Back Cancellation: 9 (added in Release 9.6(1))
Call Back Notification: 10 (added in Release 9.6(1))
Extension Status: 11 (added in Release 9.6(1))
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
PRI AOC Invoke Type (Tag: 4222)
Table 1-166
PRI AOC Invoke Type Description Form
Name: PRI AOC Invoke Type
Tag: 4222
Source: MDL
Description/Purpose: Allows the user to determine whether the supplementary services were invoked due to receipt of an
invoke component from user (PER CALL) or has been configured to be set up for all PRI calls (ALL CALLS).
Format: BE
Length in Octets: 1
Data Value:
PRI AOC Invoke Type information is 1 Octet and is defined as follows:
PER CALL: 1
ALL CALLS: 2
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-145
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
PRI AOC – S Charge Information (Tag: 4223)
Table 1-167
PRI AOC – S Charge Information Description Form
Name: PRI AOC – S Charge Information
Tag: 4223
Source: MDL
Description/Purpose: Contains Charging Tariff Information that has been setup for AOC – S Supplementary services. It
comprises the following data items:
•
tariff id and timestamped (from octet 1–6) may be repeated (up to 11 occurrences). The repetition depends on the
number of different tariffs applied for a given call and the maximum number of tariffs allowed per day is 11.
Format: BE
Length in Octets: 6, 12, 18, 24, 30, 36, 42, 48, 54, 60, or 66
Data Value:
Octets 1-2: integer value range 0-9999 (tariff id)
Octets 3-6: Time in UNIX format (timestamp associated with tariff id in octets 1-2)
Extended Data Value: No extended value.
General Information: Octets 1-6 may be repeated up to 11 times to allow for up to 11 tariff changes during the call.
Timestamps in octets 3-6 is in Unix format (as CDB Timepoint tag 4001).
MGC Release: Release 9.5(2) and later.
PRI AOC – D Charge Information (Tag: 4224)
Table 1-168
PRI AOC – D Charge Information Description Form
Name: PRI AOC – D Charge Information
Tag: 4224
Source: MDL
Description/Purpose: Contains Charging Tariff Information that has been setup for AOC – D Supplementary services. It
comprises the following data items:
•
tariff id and timestamped (from octet 5–10) may be repeated (up to 11 occurrences). The repetition depends on the
number of different tariffs applied for a given call and the maximum number of tariffs allowed per day is 11.
Format: BE
Length in Octets: 10, 16, 22, 28, 34, 40, 46, 52, 58, 64, or 70
Data Value:
Octets 1-4 : Total Charge (integer value)
Octets 5-6: integer value range 0-9999 (tariff id)
Octets 7-10: Time in UNIX format (timestamp associated with tariff id in octets 5-6)
Extended Data Value: No extended value.
General Information: Octets 1-6 may be repeated up to 11 times to allow for up to 11 tariff changes during the call.
Timestamps in octets 3-6 is in Unix format (as CDB Timepoint tag 4001).
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-146
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
PRI AOC – E Charge Information (Tag: 4225)
Table 1-169
PRI AOC – E Charge Information Description Form
Name: PRI AOC – E Charge Information
Tag: 4225
Source: MDL
Description/Purpose: Contains Charging Tariff Information that has been setup for AOC – E Supplementary services. It
comprises the following data items:
•
tariff id and timestamped (from octet 5–10) may be repeated (up to 11 occurrences). The repetition depends on the
number of different tariffs applied for a given call and the maximum number of tariffs allowed per day is 11.
Format: BE
Length in Octets: 10, 16, 22, 28, 34, 40, 46, 52, 58, 64, or 70
Data Value:
Octets 1-4 : Total Charge (integer value)
Octets 5-6: integer value range 0-9999 (tariff id)
Octets 7-10: Time in UNIX format (timestamp associated with tariff id in octets 5-6)
Extended Data Value: No extended value.
General Information: Octets 5-10 may be repeated up to 11 times to allow for up to 11 tariff changes during the call.
Timestamps in octets 7-10 is in Unix format (as CDB Timepoint tag 4001).
MGC Release: Release 9.5(2) and later.
PRI AOC Invoke Failure (Tag: 4226)
Table 1-170
PRI AOC Invoke Failure Description Form
Name: PRI AOC Invoke Failure
Tag: 4226
Source: MDL
Description/Purpose: PRI AOC Invoke Failure information is sent to the PRI user in case of failure to setup the charge. The
same information is recorded in this tag for each of the three AOC supplementary services.
Format: BE
Length in Octets: 3
Data Value:
PRI AOC Invoke Failure Type information is three octets and is defined as follows:
Octet 1: AOC – S Failure Type
Octet 2: AOC – D Failure Type
Octet 3: AOC – E Failure Type
Each octet can have the following values:
1 = INVALID CALL STATE
2 = NOT SUBSCRIBED
3 = CHARGE NOT AVAILABLE
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-147
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Route Optimization/Path Replacement Action (Tag: 4227)
Table 1-171
‘Route Optimization/Path Replacement Action
Name: RO/PR EXECUTED
Tag: 4227
Source: MDL
Description/Purpose: Indicates that the RO or PR service has resulted in the replacement of media channels.
Format: Integer
Length in Octets: 1
Data Value:
RO/PR operation = 1 indicates RO/PR feature invocation.
RO/PR operation = 2 indicates receipt of RO/PR feature invocation.
RO/PR operation = 3 indicates RO/PR feature loop back call (combined originating and terminating).
RO/PR operation = 4 indicates an incoming (originating) RO/PR slave half call.
RO/PR operation = 5 indicates an outgoing (terminating) RO/PR slave half call.
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.6(1) and later.
Route Optimization/Path Replacement Call Reference of Associated Call Instance (Tag: 4228)
Table 1-172
Route Optimization/Path Replacement Call Reference
Name: RO/PR Other Call Ref
Tag: 4228
Source: MDL
Description/Purpose: Indicates the call reference of the associated call instance.
Format: Integer
Length in Octets: 8
Data Value:
See CDE 4002 for more information.
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.6(1) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-148
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Route Optimization/Path Replacement Trunk Group Info (Tag: 4229)
Table 1-173
Route Optimization/Path Replacement Trunk Group Info
Name: RO/PR Replacement Trk Group Tag: 4229
Source: MDL
Description/Purpose: Indicates the trunk group id of the new replaced media channel associated with the slave call
reference.
Format: Integer
Length in Octets: 2
Data Value:
See CDE 4008 for more information.
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.6(1) and later.
Route Optimization/Path Replacement Channel Info (Tag: 4230)
Table 1-174
Route Optimization/Path Replacement Channel Info
Name: RO/PR Replacement Chan ID
Tag: 4230
Source: MDL
Description/Purpose: Indicates that the channel id of the new media path associated with the slave call reference.
Format: Integer
Length in Octets: 2
Data Value:
See CDE 4009 for more information.
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.6(1) and later.
Route Optimization Switchover Timestamp (Tag: 4231)
Table 1-175
Route Optimization Switchover Timestamp
Name: RO/PR Switchover Timestamp
Tag: 4231
Source: MDL
Description/Purpose: Indicates the point in time that media replacement occurred.
Format: Integer
Length in Octets: 4
Data Value:
Time in UNIX format. See CDE 4001.
ANSI/ITU Variations: None.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-149
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-175
Route Optimization Switchover Timestamp (continued)
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.6(1) and later.
Rejecting Location Label (Tag: 4232)
Table 1-176
Rejecting Location Label Description Form
Name: Rejecting Location Label
Tag: 4232
Source: MDL
Description/Purpose: Name of the Call-limiting location label which caused the call rejection.
Format: IA5 (string)
Data Value:
Length in Octets: 1–20
String
Example: londonVpnUser652
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information: For calls with location labels defined, a call limiting check must be made once the terminating side
is set up. This involves reading internal tables to get call limit data and active call counter data. If the call limit threshold
is reached, then the call is rejected against that location label. This record provides the identity of the location label that
failed the call.
This tag is only added to the CDB if the call limiting check results in rejection.
MGC Release: Release 9.6(1) and later.
Rejecting Location Label Direction (Tag: 4233)
Table 1-177
Rejecting Location Label Direction Form
Name: Rejecting Location Label Direction Tag: 4233
Source: MDL
Description/Purpose: Indication of whether or not the call was rejected by a location label relating to the MGC originating
(incoming) or terminating (outgoing) side.
Format: BE
Length in Octets: 1
Data Value:
1 = Inbound (MGC originating side)
2 = Outbound (MGC terminating side)
ANSI/ITU Variations: None.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-150
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1-177
Rejecting Location Label Direction Form (continued)
Extended Data Value: No extended value.
General Information: For calls with location labels defined, a call admission check must be made once the terminating
side is set up. This involves reading internal tables to get call limit data and active call counter data. If the call limit
threshold is reached, then the call is rejected against that location label. This record provides an indication of whether or
not this call rejection was assigned to the MGC originating (inbound) or MGC terminating (outbound) side.
This tag is added to the CDB only if the call admission check results in rejection.
MGC Release: Release 9.6(1) and later.
Total Circuit Count (Tag: 4234)
Table 1-178
Total Circuit Count Description Form
Name: Total Circuit Count
Tag: 4234
Source: Engine
Description/Purpose: Identifies the total circuits (CICs) defined for a trunk group or signaling service.
Format: BE
Length in Octets: 4
Data Value:
0 or greater (unsigned)
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.4(1) patch and later.
Total Circuits Unavailable Count (Tag: 4235)
Table 1-179
Total Circuits Unavailable Count Description Form
Name: Total Circuits Unavailable Count
Tag: 4235
Source: Engine
Description/Purpose: Identifies the total circuits (CICs) currently unavailable within a trunk group or SigPath. The
definition of unavailable is a circuit that is either “blocked” or “OOS”. A circuit that is already blocked, but which then
goes OOS, is not reported additionally as unavailable, since it was already unavailable.
Format: BE
Length in Octets: 4
Data Value:
0 or greater
ANSI/ITU Variations: None.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.4(1) patch and later.
H323 Destination (Tag 4236)
Table 1-180
H323 Destination Description Form
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-151
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Table 1:
Name: H323 Destination
Tag: 4236
Source: MDL
Description/Purpose: Identifieds the H323 Destination Address associated with the terminal trunk group or sigPath.
Format: IA5
Length in Octet: 1 to 29
Data Value: Content: [IP Address]:[Port]
Extended Data Value: No extended value.
General Information: This destination address is used to indicate the H323 address that was used in Non-RAS mode. So
this address will be the same as H323PriAddr:H323PriPort or H323AltAddr:H323AltPort that are defined in
sigPath/Trunkgroup property.
MGC Release: Release 9.7.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-152
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Ingress Redirecting Number (Tag 4237)
Table 1-181
Ingress Redirecting Number Description Form
Name: Ingress Redirecting Number
Tag: 4237
Source: MDL/Engine
Description/Purpose: This CDE records the digits from the redirecting number received by the MGC.
Format: IA5 Length in Octet: 1
Data Value: Character string containing the forwarded station’s address or subscriber number.
Extended Data Value: No extended value.
General Information:
Note
This CDE is present in the 1060 CDB if the End-of-Call CDB (1110) is configured. For point-in-call mode, the 1060
CDB is usually a short one and does not contain this CDB.
MGC Release: Release 9.5(2) patch xx.
Service Usage Data (Tag 4239)
Table 1-182
Service Usage Data Description Form
Name: Service Usage Data
Tag: 4239
Source: MDL
Description/Purpose: Indicates services invoked or transited using the feature inter-working containers.
Format: Structured variable
Data Value:
Length in Octet: 2
Octet 1: Service Name
1= MWI (Message Waiting Indicator) , 2=SSCT (Single Step Call Transfer), 3= RO (Route Optimization), 4=Call
Transferred, 5=CB (Busy) Request, 6=CB (No replay) Request, 7=CB Free Notification, 8=CB Call Setup, 9=CB Cancel,
10=Extension Status, 11=Call Diversion (unconditional), 12=Call Diversion (busy), 13=Call Diversion (no reply)
Octet 2: Service Action
1=Request, 2=Executed, 3=Rejected, 4=Activate, 5=Deactivate, 6=Initiated
Extended Data Value: No extended value.
General Information:
This CDE is present in the following CDBs: 1030, 1040, 1110. This CDE is not present in the following CDBs: 1010, 1020,
1050, 1060, 1070, 1080, 1111.
MGC Release: Release 9.7.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-153
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
CNAM DIP (Tag 4240)
Table 1-183
CNAM DIP Description Form
Name: CNAM DIP
Tag: 4240
Source: MDL
Description/Purpose: This feature indicates whether a called party has subscribed to the Calling Name Delivery (CNAM)
feature. The feature allows the name of the calling party to be delivered to the called party.
Format: Structured Variable
Length in Octet: 2
Data Value: Indicates whether the CNAM feature is invoked by the called party.
Octet 1: Query Indicator
0 = CNAM not invoked, 1 = CNAM invoked
Octet 2: Query Result Indicator
0 = Success, 1 = Return Error, 2 = Return Reject, 3 = Query Timeout, 4 = Query Abandon
Extended Data Value: No extended value.
General Information:
This CDE is present in the following CDBs: 1010, 1030, 1040, 1100. This CDE is not present in the following CDBs: 1020,
1050, 1060, 1070, 1080, 1111.
MGC Release: Release 9.7.
Calling Party Name (Tag 4241)
Table 1-184
Calling Name Description Form
Name: Calling Name
Tag: 4241
Source: MDL
Description/Purpose: The calling party name (CNAM) is provided via the SCP or orignal call setup message. The CNAM
is then passed to the egress destination if permitted based on CNAB and CIDS information. Calling Name is a terminating
feature.
Format: Structured Variable
Length in Octet: 1-15
Data Value: Characters of calling name displayed on the terminating side.
Example: Bob Johnson
Extended Data Value: No extended value.
General Information: This CDE is present in the following CDBs: 1010, 1030, 1040, 1100. This CDE is not present in the
following CDBs: 1020, 1050, 1060, 1070, 1080, 1111.
MGC Release: Release 9.7.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-154
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Terminating Remote SIP Host (Tag 4242)
Table 1-185
Terminating Remote SIP Host Description Form
Name: Terminating Remote SIP Host
Tag: 4242
Source: MDL/Engine
Description/Purpose: Contains the remote host (the To Host for a SIP call when sending a REQUEST from the PGW on the
terminating side) for the terminating side of a call. This tag is present only if SIP appears on the terminating side of the call
Format: IA5
Length in Octet: 1-256
Data Value: URL
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.7(3)
Terminating Local SIP Host (Tag 4243)
Table 1-186
Terminating Local SIP Host Description Form
Name: Terminating Local SIP Host
Tag: 4243
Source: MDL/Engine
Description/Purpose: Contains the local host (the From Host for a SIP call when sending a REQUEST from the PGW on
the terminating side) for the terminating side of a call. This tag is present only if the terminating side of the call is SIP.
Format: IA5
Length in Octet: 1-256
Data Value: URL
Extended Data Value: No extended value.
General Information:
MGC Release: Release 9.7(3)
License Rejecting Reason (Tag 4244)
Table 1-187
License Rejecting Reason Description Form
Name: License Rejecting Reason
Tag: 4244
Source: MDL
Description/Purpose: Description of the reason for the call rejection due to license management.
Format: IA5(string)
Length in Octet: 1-20
Data Value: String. Example: “SS7 Interface”
Extended Data Value: No extended value.
General Information:
The PGW performs a license check for calls with License Control. If the license limit threshold is reached or no license
exists for the protocol interface, the call will be rejected. This record provides the identity of the License that the call failed
to meet.
This CDE is present in the following CDBs: 1030, 1110. This CDE is not present in the following CDBs: 1010, 1020, 1040,
1050, 1060, 1070, 1080.
Note
This tag is only added to the CDB if the call admission check results in rejection.
MGC Release: Release 9.7(3).
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-155
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
License Rejecting Direction (Tag 4245)
Table 1-188
License Rejecting Direction Description Form
Name: License Rejecting Direction
Tag: 4245
Source: MDL
Description/Purpose: Indication of whether the call rejection was due to a license violation from incoming or outgoing
traffic to the PGW.
Format: BE
Length in Octet: 1
Data Value:
1 = Inbound (PGW originating side)
2 = Outbound (PGW terminating side)
Extended Data Value: No extended value.
General Information:
The PGW performs a license check for calls with License Control. If the license limit threshold is reached or no license
exists for the protocol interface, the call will be rejected. This record provides an indication of whether the call rejection
was due to a license violation from incoming or outgoing traffic to the PGW.
This CDE is present in the following CDBs: 1030, 1110. This CDE is not present in the following CDBs: 1010, 1020, 1040,
1050, 1060, 1070, 1080.
Note
This tag is only added to the CDB if the call admission check results in rejection.
MGC Release: Release 9.7(3).
SIP Transport (Tag 4246)
Table 1-189
SIP Transport Description Form
Name: SIP Transport
Tag: 4246
Source: MDL
Description/Purpose: Indicates the transport protocol that the PGW uses for SIP messages.
Format: Structured variable
Data Value:
Length in Octet: 1
1 = UDP (Default)
2 = TCP
Extended Data Value: No extended value.
General Information:
This CDE is present in the following CDBs: 1030, 1110. This CDE is not present in the following CDBs: 1010, 1020, 1040,
1050, 1060, 1070, 1080, 1100, 1111.
MGC Release: Release 9.7.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-156
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
SIP Routing URI Source (Tag 4247)
Table 1-190
SIP Routing URI Source Description Form
Name: SIP Routing URI Source
Tag: 4247
Source: MDL/Engine
Description/Purpose: Indicates which header or URL was used to make routing decisions.
Format: Integer
Length in Octet: 1
Data Value:
1 = Top Route: header
2 = Request URL
3 = To: Header
Extended Data Value: No extended value.
General Information:
This CDE is present in the following CDBs: 1010, 1030, 1100. This CDE is not present in the following CDBs: 1020, 1040,
1050, 1060, 1070, 1080.
MGC Release: Release 9.7.
SIP Routing URI (Tag 4248)
Table 1-191
SIP Routing URI Description Form
Name: SIP Routing URI
Tag: 4248
Source: MDL/Engine
Description/Purpose: Contains the original URI used in the initial routing decisions.
Format: IA5
Length in Octet: 1-256
Data Value:
URL
Extended Data Value: No extended value.
General Information:
This CDE is present in the following CDBs: 1010, 1030, 1100. This CDE is not present in the following CDBs: 1020, 1040,
1050, 1060, 1070, 1080.
MGC Release: Release 9.7.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-157
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Millisecond Granularity CDEs
IAM Timepoint Received_ms (Tag: 4100)
Table 1-192
IAM Timepoint Received_ms Description Form
Name: IAM Timepoint Received_ms
Tag: 4100
Source: MDL/Engine
Description/Purpose: The IAM timepoint received is the recorded timepoint when the IAM was received, in milliseconds
since 1970.
Format: Binary
Length in Octets: 6
Data Value: Cisco MGC time plus 2 bytes for milliseconds
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
IAM Timepoint Sent_ms (Tag: 4101)
Table 1-193
IAM Timepoint Sent_ms Description Form
Name: IAM Timepoint Sent_ms
Tag: 4101
Source: MDL/Engine
Description/Purpose: The IAM timepoint sent is the recorded timepoint when the IAM was sent, in milliseconds since
1970.
Format: Binary
Length in Octets: 6
Data Value: Cisco MGC time plus 2 bytes for milliseconds
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
ACM Timepoint Received_ms (Tag: 4102)
Table 1-194
ACM Timepoint Received_ms Description Form
Name: ACM Timepoint Received_ms
Tag: 4102
Source: MDL/Engine
Description/Purpose: The ACM timepoint received is the recorded timepoint when the ACM was received, in milliseconds
since 1970.
Format: Binary
Length in Octets: 6
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-158
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
ACM Timepoint Sent_ms (Tag: 4103)
Table 1-195
ACM Timepoint Sent_ms Description Form
Name: ACM Timepoint Sent_ms
Tag: 4103
Source: MDL/Engine
Description/Purpose: The ACM timepoint sent is the recorded timepoint when the ACM was sent, in milliseconds since
1970.
Format: Binary
Length in Octets: 6
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
ANM Timepoint Received_ms (Tag: 4104)
Table 1-196
ANM Timepoint Received_ms Description Form
Name: ANM Timepoint Received_ms
Description/Purpose: Recorded timepoint when the ANM was received, in milliseconds since 1970.
Format: Binary Length in Octets: 6
Tag: 4104
Source: MDL/Engine
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
ANM Timepoint Sent_ms (Tag: 4105)
Table 1-197
ANM Timepoint Sent_ms Description Form
Name: ANM Timepoint Sent_ms
Description/Purpose: Recorded timepoint when the ANM was sent, in milliseconds since 1970.
Format: Binary Length in Octets: 6
Tag: 4105
Source: MDL/Engine
Data Value: Cisco MGC time plus 2 bytes for milliseconds,
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-159
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
First REL Timepoint_ms (Tag: 4106)
Table 1-198
First REL Timepoint_ms Description Form
Name: First REL Timepoint_ms
Tag: 4106
Source: MDL/Engine
Description/Purpose: Timepoint for receipt of first REL/RELEASE.
Format: Binary Length in Octets: 6
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Second REL Timepoint _ms (Tag: 4107)
Table 1-199
Second REL Timepoint _ms Description Form
Name: Second REL Timepoint_ms
Description/Purpose: Timepoint for receipt of second REL/RELEASE.
Format: Binary Length in Octets: 6
Tag: 4107
Source: MDL/Engine
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
RLC Timepoint Received_ms (Tag: 4108)
Table 1-200
RLC Timepoint Received_ms Description Form
Name: RLC Timepoint Received_ms
Description/Purpose: Recorded timepoint when the RLC was received, in milliseconds since 1970.
Format: Binary Length in Octets: 6
Tag: 4108
Source: MDL/Engine
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-160
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
RLC Timepoint Sent_ms (Tag: 4109)
Table 1-201
RLC Timepoint Sent_ms Description Form
Name: RLC Timepoint Sent_ms
Tag: 4109
Source: MDL/Engine
Description/Purpose: Recorded timepoint when the RLC was sent, in milliseconds since 1970.
Format: Binary Length in Octets: 6
Data Value: Cisco MGC time plus 2 bytes for milliseconds.
Extended Data Value: No extended value.
General Information:
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-161
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Cisco Reserved CDEs
Unique Call Correlator ID (Tag: 5000)
Table 1-202
Unique Call Correlator ID Description Form
Name: Unique Call Correlator ID
Tag: 5000
Source:
MDL/Engine/External
Description/Purpose: A Unique Call ID can be created by an MGC or a media gateway, depending on the origin of a call.
The purpose of this field is to uniquely identify a single call across a multinode Cisco MGC solution, and/or to provide a
common key for all involved recording systems. This information can be used to associate external billing information,
such as RADIUS records, and correlate multiple Cisco MGCs to what is considered a single call. The records created by
the various network elements can be used by downstream systems (that is, mediation) after correlation for billing and other
purposes.
Format: Structured variable
Length in Octets: 16
Value
Octet
1 – 4
5 – 6
7 – 8
Field
Bits
Meaning
time_low
8 – 1
8 – 1
8 – 1
Unsigned 32-bit integer
Unsigned 16-bit integer
Unsigned 16-bit integer
The low field of the timestamp
The middle field of the timestamp
time_mid
time_hi_and_version
The high field of the timestamp multiplexed
with the version number
9
clock_seq_hi_and_
reserved
8 – 1
Unsigned 8-bit integer
The high field of the clock sequence
multiplexed with the variant
10
clock_seq_low
node
8 – 1
8 – 1
Unsigned 8-bit integer
Unsigned 48-bit integer
The low field of the clock sequence
The spatially unique node identifier
11 – 16
Data Value:
The timestamp contains the number of 100 nanosecond intervals since October 15, 1582.
The spatially unique node identifier contains the hardware address of the system primary Ethernet adapter.
See ITU-T Recommendation H.225.0 for further details.
Extended Data Value: No extended value.
General Information: This field is required in every CDB.
MGC Release: Release 9.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-162
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Miscellaneous Fields
MGC ID (Tag: 6000)
Table 1-203
MGC ID Description Form
Name: MGC ID
Tag: 6000
Source: CDR Dumper
Description/Purpose: Indicates the MGC ID on which the CDR file was created.
Format: IA5
Length in Octets: 1-32
Data Value: IA5 string
Extended Data Value: No extended value.
General Information: This field is used (only) by the CDR dumper to generate the file header CDB record and the file footer
CDB record.
MGC Release: Release 7.0 and later.
File Start Time (Tag: 6001)
Table 1-204
File Start Time Description Form
Name: File Start Time
Description/Purpose: Indicates the start time of a CDR file timespan.
Format: BE Length in Octets: 4
Tag: 6001
Source: CDR Dumper
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This field is created by the CDR dumper to generate the file header CDB record.
MGC Release: Release 7.0 and later.
File End Time (Tag: 6002)
Table 1-205
File End Time Description Form
Name: File End Time
Description/Purpose: Indicates the end time of a CDR file timespan.
Format: BE Length in Octets: 4
Tag: 6002
Source: CDR Dumper
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This field is created by the CDR dumper to generate the file footer CDB record.
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-163
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Total Number of CDB Records (Tag: 6003)
Table 1-206
Total Number of CDB Records Description Form
Name: Total Number of CDB Records
Tag: 6003
Source: CDR Dumper
Description/Purpose: Indicates the total number of CDB records included in the CDR file.
Format: BE Length in Octets: 4
Data Value: UNIX time format (number of seconds since January 1, 1970).
Extended Data Value: No extended value.
General Information: This field is created by the CDR dumper to generate the file footer CDB record.
MGC Release: Release 7.0 and later.
MGC Version (Tag: 6004)
Table 1-207
MGC Version Description Form
Name: MGC Version
Tag: 6004
Source: CDR Dumper
Description/Purpose: Indicates the Cisco MGC software version.
Format: ASCII
Length in Octets: 10
Data Value: ASCII string
Extended Data Value: No extended value.
General Information: This field is used (only) by the CDR dumper to generate the file header CDB record and the file footer
CDB record.
MGC Release: Release 7.0 and later.
Interim CDB (Tag: 6005)
Table 1-208
Interim CDB Description Form
Name: Interim CDB
Description/Purpose: Indicates that this is an interim CDB and there are further CDBs to follow for this call.
Format: BE Length in Octets: 1
Tag: 6005
Source: MDL
Data Value: 1 = Interim CDB - further CDBs to follow
Extended Data Value: No extended value.
General Information: Used when sending multiple CDBs to indicate that there are further CDBs to be sent that are
associated with this call ID.
MGC Release: Release 9.5(2) and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-164
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
Protocol Specific CDEs
NTT
TTC Contract Number (Tag: 6100)
Table 1-209
TTC Contract Number Description Form
Name: TTC Contract Number
Tag: 6100
Source: MDL
Description/Purpose: Digits from the Contract Number Parameter of TTC-Q763a.
Format: IA5
Length in Octets: 3 to 12
Data Value: Digits
Extended Data Value: No extended value.
General Information: This field is used (only) when the Cisco MGC is configured with the TTC signaling protocol.
MGC Release: Release 7.0 and later.
TTC Contract Number NOA (Tag: 6101)
Table 1-210
TTC Contract Number NOA Description Form
Name: TTC Contract Number NOA
Tag: 6101
Source: MDL
Description/Purpose: Nature of Address field of Contract Number Parameter from TTC-Q.763a.
Format: IA5
Length in Octets: 1
Data Value: 1 octet
Extended Data Value: No extended value.
General Information: This field is used (only) when the Cisco MGC is configured with the TTC signaling protocol.
MGC Release: Release 7.0 and later.
TTC Charge Info (Tag: 6102)
Table 1-211
TTC Charge Info Description Form
Name: TTC Charge Info
Tag: 6102
Source: MDL
Description/Purpose: From TTC-Q.763a Charge Information Parameter.
Format: IA5
Length in Octets: 3 to n, where the field configuration is specified separately
for each network
Data Value: Sequence of octets
Extended Data Value: No extended value.
General Information: This field is used (only) when the Cisco MGC is configured with the TTC signaling protocol.
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-165
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Billing Interfaces
CDE Detail Description
TTC Charge Info Type (Tag: 6103)
Table 1-212
TTC Charge Info Type Description Form
Name: TTC Charge Info Type
Tag: 6103
Source: MDL
Description/Purpose: This parameter is taken from the TTC-Q.763a Charge Information parameter.
Format: IA5
Length in Octets: 3 to n, where the field configuration is specified separately
for each network
Data Value: Sequence of octets
Extended Data Value: No extended value.
General Information: This field is used (only) when the Cisco MGC is configured with the TTC signaling protocol.
MGC Release: Release 7.0 and later.
TTC Charge Area Info (Tag: 6104)
Table 1-213
TTC Charge Area Info Description Form
Name: TTC Charge Area Info
Tag: 6104
Source: MDL
Description/Purpose: This parameter is taken from the TTC-Q.763a Charge Originating Info parameter.
Format: IA5
Length in Octets: 3 to 6
Data Value: Sequence of octets
Extended Data Value: No extended value.
General Information: This field is used (only) when the Cisco MGC is configured with the TTC signaling protocol.
MGC Release: Release 7.0 and later.
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
1-166
Download from Www.Somanuals.com. All Manuals Search And Download.
C H A P T E R
2
MGC Info Field Reference
This chapter provides additional information about the MGC Info Field (Tag 4031), described in
Chapter 1, “Billing Interfaces” The MGC info field consists of several subfields, that are stored in the
value section of the VSC info field. These subfields contain no tags or values. The MGC Info field
provides the customer with backward compatibility to Cisco MGC Software Release 5.0 and earlier.
Table 2-1 describes each MGC Info subfield, including its exact position in the value section of the VSC
info field.
Table 2-1
MGC Info Subfields
Location
(Position)
Field Name
Description
Value/Encoding Scheme
Size
In Signal path ID
This is the ID for the originating C7 – Component ID for the
1 (first octet) 2
Signal Path
Point Code
Binary Big-endian
In traffic channel ID
In protocol ID
This is the ID for the originating Binary Big-endian
traffic Channel
3 (start at
third octet)
2
1
This is the numeric representation 0 = ISDN PRI
5
of the protocol family for the
originating side
1 = C7
2 = DPNSS
3 = CAS
4 = ASN
5 = Unknown
Binary Big-endian
Out Signal path ID
This is the ID for the terminating C7 – Component ID for the
6
8
2
2
Signal Path.
Point Code
Binary Big-endian
Out traffic channel ID This is the ID for the terminating (Binary Big-endian
traffic Channel
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
MGC Info Subfields
Table 2-1
MGC Info Subfields (continued)
Location
(Position)
Field Name
Description
Value/Encoding Scheme
Size
Out protocol ID
This is the numeric representation 0 = ISDN PRI
10
1
of the protocol family for the
originating side
1 = C7
2 = DPNSS
3 = CAS
4 = ASN
5 = Unknown
Binary Big-endian
Call Type Flag
This indicates whether the call
was a real or virtual call [used
primarily in DPNSS]
0 = Real call
1 = Virtual Call
Binary Big-endian
11
12
1
1
Call Feature Flag
This indicates whether the call
0 = Normal Call
was a normal call or a feature call 1 = Feature Call
(that is, call forwarding, or call
waiting)
Binary Big-endian
C-NOA Pre-translated Cisco specific: Nature of address
13
14
15
16
17
1
1
1
1
1
calling number
(NOA) for pre-translated calling
number. This field is used for
backward compatibility.
C-NOA Pre-translated Cisco specific: NOA for
(
dialed number
pre-translated dialed number.
This field is used for backward
compatibility.
C-NOA Post-translated Cisco specific:NOA for
calling number
post-translated calling number.
This field is used for backward
compatibility.
C-NOA Post-translated Cisco specific: NOA for
dialed number
post-translated dialed number.
This field is used for backward
compatibility.
C-CPC Call Type
Cisco specific: Unknown,
ordinary, Priority, Emergency,
Data
0 = Unknown call value
1 = Ordinary Call
2 = Priority Call
3 = Emergency Call
5 = Data Call
(Priority Call & Data Call for
ANSI SS7 is not supported)
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
MGC Info Subfields
Table 2-1
MGC Info Subfields (continued)
Location
(Position)
Field Name
Description
Value/Encoding Scheme
Size
C-CPC Language
Cisco specific: French, English, 1 = Unknown Language
18
1
..etc
2 = English
3 = Russian
4 = French
5 = German
6 = Spanish
C-CPC User
Cisco specific: Unknown,
Subscriber, Operator,…etc
0 = Unknown User
1 = Subscriber User
2 = Operator
19
1
3 = Pay phone
4 = EMERGENCY
5 = NETWORK
6 = ATT PR1
7 = ATT PR2
8 = ATT PR3
9 = ATT PR4
10 = ATT PR5
11 = CGSUB PR2
12 = CGSUB PR3
13 = CGSUB PR4
14 = CGSUB PR5
15 = SERVICE LINE
16 = DPNSS
17 = CONF DEVICE
18 = ALARM DEVICE
19 = PAYPHONE TYPE2
20 = PAYPHONE TYPE3
21 = PAYPHONE TYPE4
22 = PBX SUBSCRIBER1
23 = PBX SUBSCRIBER2
24 = PBX SUBSCRIBER3
25 = PBX SUBSCRIBER4
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
MGC Info Subfields
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
A P P E N D I X
A
CDE Listings by Release
This appendix lists the valid call detail elements (CDEs) on a release-by-release basis. The valid CDEs
•
•
•
•
•
•
•
•
CDE Baseline—Release 9.1(5) and Higher, page A-1
CDE Changes in Release 9.7, page A-8
Table A-1 lists the CDEs that are valid as of Release 9.1(5).
Table A-1
Valid CDEs for Release 9.1(5) and Higher
Tag Value
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
Field Name
Calling Party Category
User Service Information
Originating Line Information
Calling Number Nature of Address
Charged Number Nature of Address
Dialed Number Nature of Address
LRN Nature of Address
Called Number Nature of Address
Reason Code
Forward Call Indicators Received
Forward Call Indicators Sent
Nature of Connection Indicators Received
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Baseline—Release 9.1(5) and Higher
Table A-1
Valid CDEs for Release 9.1(5) and Higher (continued)
Tag Value
2012
2013
2014
2015
2016
2017
3000
3001
3003
3005
3006
3007
3008
3009
3010
3011
3012
3013
3017
4000
4001
4002
4003
4004
4005
4006
4007
4008
4009
4010
4011
4012
4013
4014
4015
4016
Field Name
Nature of Connection Indicators Sent
Transit Network Selection
Carrier Identification Parameter
Carrier Selection Parameter
Jurisdiction Information Parameter
Redirecting Number NOA
Calling Party Category
User Service Information
Calling Number Nature of Address
Dialed Number Nature of Address
LRN Nature of Address
Called Number Nature of Address
Reason Code
Forward Call Indicators Received
Forward Call Indicators Sent
Nature of Connection Indicators Received
Nature of Connection Indicators Sent
Transit Network Selection
Redirecting Number NOA
CDB Version
CDB Timepoint
Call Reference ID
IAM Timepoint
ACM Timepoint
ANM Timepoint
REL Timepoint
Crash Timepoint
Originating Trunk Group
Originating Member
Calling Number
Charged Number
Dialed Number
LRN Number
Called Number
Terminating Trunk Group
Terminating Member
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Baseline—Release 9.1(5) and Higher
Table A-1
Valid CDEs for Release 9.1(5) and Higher (continued)
Tag Value
4017
4018
4019
4020
4028
4029
4030
4032
4033
4034
4035
4036
4037
4038
4039
4040
4041
4042
4043
4044
4045
4048
4049
4050
4052
4053
4060
4061
4062
4063
4066
4067
4068
4069
4070
4071
Field Name
Maint Trunk Group
Maint Circuit Member
Glare Encountered
RLC Release Timepoint
First Release Source
LNP Dip
Total Meter Pulses
Maint Type
Maint Reason
Ingress Originating Point Code
Ingress Destination Point Code
Egress Originating Point Code
Egress Destination Point Code
Ingress Media Gateway ID
Egress Media Gateway ID
TCAP Transaction Identification
Transaction Start Time
Transaction End Time
TCAP Database Identification
Announcement Identification
Route Selection Info
Directional Flag
Service Logic ID
AMA Line Number
Originating Gateway Primary Select
Terminating Gateway Primary Select
Redirecting Number
Tariff Rate
Scale Factor
Test Line Indicator
Ingress SigPath ID
Ingress Span ID
Ingress BearChan ID
Ingress Protocol ID
Egress SigPath ID
Egress Span ID
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.2(2)
Table A-1
Valid CDEs for Release 9.1(5) and Higher (continued)
Tag Value
4072
4073
4074
4075
4076
4077
4100
4101
4102
4103
4104
4105
4106
4107
4108
4109
4201
4202
4203
5000
6000
6001
6002
6003
6004
6100
6101
6102
6103
6104
Field Name
Egress BearChan ID
Egress Protocol ID
Maintenance SigPath ID
Maintenance Span ID
Maintenance BearChan ID
Maintenance Circuits Count
IAM Timepoint Received_ms
IAM Timepoint Sent_ms
ACM Timepoint Received_ms
ACM Timepoint Sent_ms
ANM Timepoint Received_ms
ANM Timepoint Sent_ms
First REL Timepoint_ms
Second REL Timepoint_ms
RLC Timepoint Received_ms
RLC Timepoint Sent_ms
Ingress SIP URL
Egress SIP URL
SIP Call ID
Unique Call Correlator ID
MGC ID
File Start Time
File End Time
Total Number of CDB records
MGC Version
TTC Contract #
TTC Contract # NOA
TTC Charge Info
TTC Charge Info Type
TTC Charge Area Info
CDE Changes in Release 9.2(2)
There are no CDE changes in Release 9.2(2).
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.3(1)
Table A-2 lists the CDEs that are valid as of Release 9.3(1).
Table A-2
CDE Changes in Release 9.3(1)
Tag Value
4078
Field Name
Action
Charge Band Number
Added
4079
Furnish Charging Information Added
Original Called Number Added
4080
Table A-3 lists the CDEs that are valid as of Release 9.3(2).
Table A-3
CDE Changes in Release 9.3(2)
Tag Value
Field Name
Action
4034
Ingress Originating Point Code Existed, added to
the 1110 CDB
4035
4036
4037
4068
4072
Ingress Destination Point Code Existed, added to
the 1110 CDB
Egress Originating Point Code Existed, added to
the 1110 CDB
Egress Destination Point Code Existed, added to
the 1110 CDB
Ingress BearChan ID
Existed, added to
the 1110 CDB
Egress BearChan ID
Existed, added to
the 1110 CDB
4081
4082
T.38 Fax Call
Added
Added
Charge Unit Number
Table A-4 lists the CDE changes for Release 9.4(1).
Table A-4
CDE Changes in Release 9.4(1)
Tag Value
Field Name
Action
1071 CDB Circuit Audit CDB
Added
4033
4046
Maint Reason
Retired
Restored
Ingress Gateway Packet Info
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.5(2)
Table A-4
CDE Changes in Release 9.4(1) (continued)
Tag Value
4047
4098
4099
4204
4205
4206
4207
4208
4209
4210
4211
4212
4234
4235
Field Name
Action
Restored
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Egress Gateway Packet Info
Originating Leg DSP Statistics
Terminating Leg DSP Statistics
Source IP Address
Ingress Media Device Address
Egress Media Device Address
Initial Codec
Final Codec
Ingress Media Device Port
Egress Media Device Port
Originating VPN ID
Terminating VPN ID
Total Circuits Count
Total Circuits Unavailable Count
Table A-5 lists the CDE changes for Release 9.5(2).
Table A-5
CDE Changes in Release 9.5(2)
Tag Value
2018
2019
2020
3018
3019
3020
4044
4045
4083
4084
4085
4086
4087
4088
4089
Field Name
Action
Egress Calling Number NOA
Egress Redirecting Number NOA
Added in a patch
Added in a patch
Egress Original Called Number NOA Added in a patch
Egress Calling Number NOA
Added in a patch
Added in a patch
Egress Redirecting Number NOA
Egress Original Called Number NOA Added in a patch
Announcement Identification
Route Selection Info
Egress Media Device Address
Initial Codec
Modified, added to CDB 1030
Retired
Added
Added
Added
Added
Added
Added
Added
Final Codec
Ingress Media Device Port
Egress Media Device Port
Originating VPN ID
Terminating VPN ID
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.6(1)
Table A-5
CDE Changes in Release 9.5(2) (continued)
Tag Value
4090
4091
4092
4093
4094
4095
4096
4097
4213
4214
4215
4216
4217
4218
4219
4220
Field Name
Action
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Reservation Request Accepted
Reservation Request Accepted
ATM Ingress Configured Profile
ATM Egress Configured Profile
ATM Negotiated Profile
Route List Name
Route Name
MGCP Script Response String
Meter Pulses Received
Meter Pulses Sent
Charge Tariff Info
Advice of Charge Indicator
Short Call Indicator
Charge Limit Exceeded
Call Recovered Indication
PARTIAL CALLING LINE
IDENTITY
4221
4222
4223
4224
4225
4226
4237
6005
Service Activation
Added
PRI AOC Invoke Type
Added
PRI AOC – S Charge Information
PRI AOC – D Charge Information
PRI AOC – E Charge Information
PRI AOC Invoke Failure
Ingress Redirecting Number
INTERIM CDB
Added
Added
Added
Added
Added in a patch
Added
Table A-5 lists the CDE changes for Release 9.6(1).
Table A-6
CDE Changes in Release 9.6(1)
Tag Value
Field Name
Action
Added
Added
Added
1210 CDB Slave End-of-Call
1260 CDB Slave Long-Call
4030
Total Meter Pulses
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.7
Table A-6
CDE Changes in Release 9.6(1) (continued)
Tag Value
Field Name
Action
4098
Originating Leg DSP Statistics
Modified for the Support of DSP
Voice Quality Statistics feature,
in patch CSCOnn026.
4099
Terminating Leg DSP Statistics
Service Activation
Modified for the Support of DSP
Voice Quality Statistics feature,
in patch CSCOnn026.
4221
4227
4228
Modified, added new data
values.
Route Optimization/Path
Replacement Action
Added
Route Optimization/Path Replacment Added
Call Reference of Associated Call
Instance
4229
4230
4231
Route Optimization/Path
Replacement Trunk Group Info
Added
Added
Added
Route Optimization/Path
Replacement Channel Info
Route Optimization Switchover
Timestamp
4232
4233
Rejecting Location Label
Added
Added
Rejecting Location Label Direction
Table A-7 lists the CDE changes for Release 9.7.
Table A-7
CDE Changes in Release 9.7
Tag Value
Field Name
Action
4046
Ingress Packet Information
Modified for the H.248 Protocol
feature.
4047
4069
4073
4087
4088
Egress Packet Information
Ingress Protocol ID
Modified for the H.248 Protocol
feature
Modified for the H.248 Protocol
feature
Egress Protocol ID
Modified for the H.248 Protocol
feature
Ingress MGCP DLCX Return Code
Egress MGCP DLCX Reture Code
Modified for the H.248 Protocol
feature
Modified for the H.248 Protocol
feature
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.7
Table A-7
CDE Changes in Release 9.7
Tag Value
Field Name
Action
4097
MGCP Script Response String
Modified for the H.248 Protocol
feature
4098
4099
4201
4202
Originating Leg DSP Statistics
Terminating Leg DSP Statistics
Ingress SIP URL
Modified for the H.248 Protocol
feature
Modified for the H.248 Protocol
feature
Name changed to Originating
Remote SIP Host.
Egress SIP URL
Name changed to Originating
Local SIP Host.
4236
4239
4240
4241
4242
4243
4244
4245
4246
4247
4248
H323 Destination
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Added
Service Usage Data
CNAM DIP
Calling Name
Terminating Remote SIP Host
Terminating Local SIP Host
License Rejecting Reason
License Rejecting Direction
SIP Transport Protocol
SIP Routing URI Source
SIP Routing URI
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
CDE Changes in Release 9.7
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
A-10
Download from Www.Somanuals.com. All Manuals Search And Download.
I N D E X
A
CDB 1-9
Announcement ID (Tag: 4044) 1-112
CDB message type 1-2
CDR 1-9
B
billing interfaces 1-1
Charged number Nature of Address
(Tag: 2004/ANSI) 1-53
C
C-NOA Pre-translated dialed number 2-2
configuring
call detail block 1-9
Called Number (Tag: 4014) 1-102
Call Feature Flag 2-2
Cisco MGC
call detail record file 1-8
configuring Cisco MGC
Calling number Nature of Address
CRASH Timepoint (Tag: 4007) 1-100
(Tag: 2003/ANSI) 1-52
D
Dialed Number (Tag: 4012) 1-102
enabling 1-8
Directional Flag (Tag: 4048) 1-114
documentation
Call Type Flag 2-2
Carrier Selection Parameter (Tag: 2015/ANSI) 1-63
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
IN-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
related publications i-xvi
J
Jurisdiction Information Parameter
(Tag: 2016/ANSI) 1-64
E
Egress Packet Info (Tag: 4047) 1-114
L
LNP Dip (Tag: 4029) 1-105
LRN Number (Tag: 4013) 1-102
F
M
MGC configuration
First REL Timepoint_ms (Tag: 4106) 1-160
Forward Call Indicators Sent (Tag: 3010/ITU) 1-89
redundant 1-20
G
MGC Info Subfields 2-1
generic interface 1-20
MGC Version (Tag: 6004) 1-164
Glare Encountered (Tag: 4019) 1-104
N
I
Nature of Connection Indicators Received
\ 4035) 1-108
Nature of Connection Indicators Received
Nature of Connection indicators Sent
Nature of Connection indicators Sent
NTP 1-21
In traffic channel ID 2-1
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
IN-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Transit Network Selection (Tag
O
\ 2013/ANSI) 1-62
Originating Line Information (Tag
\ 3002/ITU) 1-70
TTC Contract Number NOA (Tag: 6101) 1-165
U
Out traffic channel ID 2-1
User Service Information (Tag: 3001/ITU) 1-69
R
X
Reason Code (Tag: 3008/ITU) 1-75
XECfgParm.dat
Route Selection Info (Tag: 4045) 1-112
enabling call screening database 1-8
S
Service Logic ID (Tag: 4049) 1-115
T
tag values 1-3
Transaction Start Time (Tag: 4041) 1-111
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
IN-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Cisco Media Gateway Controller Software Release 9 Billing Interface Guide
OL-1089-11
IN-4
Download from Www.Somanuals.com. All Manuals Search And Download.
|