Christie Digital Systems Projector 38 VIV205 01 User Manual

38-VIV205-01  
MODEL  
Projection lens is optional.  
User's Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
All the safety and operating instructions should be read before  
the product is operated.  
This projector should be operated only from the type of power  
source indicated on the marking label. If you are not sure of  
the type of power supplied, consult your authorized dealer or  
local power company.  
Read all of the instructions given here and retain them for later  
use. Unplug this projector from AC power supply before  
cleaning. Do not use liquid or aerosol cleaners. Use a damp  
cloth for cleaning.  
Do not overload wall outlets and extension cords as this can  
result in fire or electric shock. Do not allow anything to rest on  
the power cord. Do not locate this projector where the cord  
may be damaged by persons walking on it.  
Follow all warnings and instructions marked on the projector.  
For added protection to the projector during a lightning storm,  
or when it is left unattended and unused for long periods of  
time, unplug it from the wall outlet. This will prevent damage  
due to lightning and power line surges.  
Do not attempt to service this projector yourself as opening or  
removing covers may expose you to dangerous voltage or  
other hazards. Refer all servicing to qualified service  
personnel.  
Unplug this projector from wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
a. When the power cord or plug is damaged or frayed.  
b. If liquid has been spilled into the projector.  
Do not expose this unit to rain or use near water... for  
example, in a wet basement, near a swimming pool, etc...  
Do not use attachments not recommended by the  
manufacturer as they may cause hazards.  
c. If the projector has been exposed to rain or water.  
d. If the projector does not operate normally by following the  
operating instructions. Adjust only those controls that are  
covered by the operating instructions as improper  
adjustment of other controls may result in damage and will  
often require extensive work by a qualified technician to  
restore the projector to normal operation.  
e. If the projector has been dropped or the cabinet has been  
damaged.  
f. When the projector exhibits a distinct change in  
performance-this indicates a need for service.  
Do not place this projector on an unstable cart, stand, or table.  
The projector may fall, causing serious injury to a child or  
adult, and serious damage to the projector. Use only with a  
cart or stand recommended by the manufacturer, or sold with  
the projector. Wall or shelf mounting should follow the  
manufacturer's instructions, and should use a mounting kit  
approved by the manufacturers.  
An appliance and cart combination should  
be moved with care. Quick stops,  
excessive force, and uneven surfaces  
may cause the appliance and cart  
combination to overturn.  
When replacement parts are required, be sure the service  
technician has used replacement parts specified by the  
manufacturer that have the same characteristics as the  
original part. Unauthorized substitutions may result in fire,  
electric shock, or injury to persons.  
Upon completion of any service or repairs to this projector, ask  
the service technician to perform routine safety checks to  
determine that the projector is in safe operating condition.  
Slots and openings in the back and bottom of the cabinet are  
provided for ventilation, to insure reliable operation of the  
equipment and to protect it from overheating.  
The openings should never be covered with cloth or other  
materials, and the bottom opening should not be blocked by  
placing the projector on a bed, sofa, rug, or other similar  
surface. This projector should never be placed near or over a  
radiator or heat register.  
This projector should not be placed in a built-in installation  
such as a book case unless proper ventilation is provided.  
Voor de klanten in Nederland  
Bij dit product zijn batterijen  
geleverd.  
Wanneer deze leeg zijn,  
moet u ze niet weggooien  
maar inleveren als KCA.  
Never push objects of any kind into this projector through  
cabinet slots as they may touch dangerous voltage points or  
short out parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the projector.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPLIANCES  
Federal Communication Commission Notice  
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and  
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try  
to correct the interference by one or more of the following measures :  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.  
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such  
changes or modifications should be made, you could be required to stop operation of the equipment.  
Model Number  
Trade Name  
Responsible party  
Address  
: 38-VIV205-01  
: Christie  
: CHRISTIE DIGITAL SYSTEMS, Inc.  
: 10550 Camden Drive Cypress, CA 90630 USA  
: (714) 236-8610  
Telephone No.  
AC POWER CORD REQUIREMENT  
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.  
AC Power Cord for the United States and Canada :  
AC Power Cord used in the United States and Canada is listed by the Underwriters  
Laboratories (UL) and certified by the Canadian Standard Association (CSA).  
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the  
plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be  
unable to insert the plug into the outlet, contact your electrician.  
GROUND  
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
FEATURES AND DESIGN  
6
7
COMPUTER MODE  
22  
SELECTING INPUT SOURCE  
SELECTING COMPUTER SYSTEM  
22  
22  
23  
23  
24  
26  
PREPARATION  
PC ADJUSTMENT  
AUTO PC ADJUSTMENT  
MANUAL PC ADJUSTMENT  
COMPATIBLE COMPUTER SPECIFICATIONS  
NAME OF EACH PART OF PROJECTOR  
7
8
8
9
9
9
10  
10  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
LENS INSTALLATION  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT  
27  
27  
28  
IMAGE LEVEL ADJUSTMENT  
POSITIONING PROJECTOR  
LENS SHIFT ADJUSTMENT  
ADJUSTABLE FEET  
PICTURE SCREEN ADJUSTMENT  
29  
MOVING PROJECTOR  
VIDEO MODE  
30  
CONNECTING PROJECTOR  
11  
SELECTING INPUT SOURCE  
SELECTING VIDEO SYSTEM  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT  
30  
31  
32  
32  
33  
TERMINALS OF PROJECTOR  
CONNECTING TO COMPUTER  
CONNECTING TO VIDEO EQUIPMENT  
11  
12  
13  
IMAGE LEVEL ADJUSTMENT  
PICTURE SCREEN ADJUSTMENT  
34  
BEFORE OPERATION  
14  
SETTING  
35  
OPERATION OF REMOTE CONTROL  
LASER POINTER FUNCTION  
14  
14  
15  
SETTING MENU  
35  
REMOTE CONTROL BATTERIES INSTALLATION  
TOP CONTROL PANEL AND INDICATORS  
16  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
17  
17  
17  
18  
APPENDIX  
37  
OPERATING WIRELESS MOUSE  
37  
MAINTENANCE  
38  
38  
38  
38  
39  
39  
WARNING TEMP. INDICATOR  
AIR FILTER CARE AND CLEANING  
CLEANING PROJECTION LENS  
LAMP REPLACEMENT  
BASIC OPERATION  
19  
TURNING ON / OFF PROJECTOR  
19  
LAMP REPLACE COUNTER  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
20  
20  
20  
20  
20  
21  
21  
21  
TROUBLESHOOTING  
TECHNICAL SPECIFICATIONS  
40  
42  
FOCUS ADJUSTMENT  
LENS SHIFT ADJUSTMENT  
KEYSTONE ADJUSTMENT  
PICTURE FREEZE FUNCTION  
NO SHOW FUNCTION  
P-TIMER FUNCTION  
SOUND ADJUSTMENT  
21  
TRADEMARKS  
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.  
IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.  
Windows and PowerPoint are registered trademarks of Microsoft Corporation.  
Each name of corporations or products in the user's manual is a trademark or a registered trademark of its  
respective corporation.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
FEATURES AND DESIGN  
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This  
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)  
technology.  
Compact Design  
Digital Zoom (for Computer)  
This projector is extremely compact in size and weight.  
It is designed to carry and work anywhere.  
The Digital Zoom function adjusts the image size to  
approx. 1/4 ~ 49 times of original image size, allowing  
you to focus on crucial information at a presentation.  
Compatibility  
Keystone Correction  
This projector accepts various video and computer input  
signals including;  
Positioning of a projector may result in distorted image  
being displayed in a trapezoid shape. Keystone  
Correction solves this problem by digitally altering  
projection to produce undistorted images.  
Computers  
IBM-compatible or Macintosh computer up to 1280  
x 1024 resolution.  
6 Color Systems  
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-  
N color system can be connected.  
Power Management  
Power Management function is provided to reduce power  
consumption while the projector is not in use.  
Component Video  
Component video signal, such as from a DVD  
player, high definition TV signals including 480i,  
480p, 575i, 575p, 720p, 1035i or 1080i, can be  
connected.  
This Power Management function operates to turn the  
Projection Lamp off when the projector detects signal  
interruption and any button is not pressed within 5  
minutes. The Projection Lamp is automatically turned on  
again when the projector detects signal or any operation  
button is pressed.  
S-Video  
S-Video signal, such as a S-VHS VCR output  
signal, can be connected.  
This projector is shipped with this function ON.  
High Resolution Image  
Digital Visual Interface  
This projector provides 1024 x 768 dots resolution for  
computer input and 800 horizontal TV lines. Resolution  
from a computer between XGA (1024 x 768) and SXGA  
(1280 x 1024) is compressed into 1024 x 768 dots. This  
projector can not display images over 1280 x 1024 dots.  
When resolution of your computer is more than 1280 x  
1024, reset a computer output for lower resolution.  
This projector is equipped with DVI 24-pin terminal for  
connecting DVI output from a computer.  
Laser Pointer Function  
The Remote Control Unit supplied with this projector  
includes a Laser Pointer function. This function helps you  
to make a smart presentation on a projected screen.  
Multi-Scan System  
This projector has Multi-Scan System to conform to  
almost all computer output signals quickly. There is no  
need for troublesome manual adjustment of frequency  
and other settings.  
Wireless Mouse  
The Remote Control Unit supplied with this projector has  
a Wireless Mouse function for a connected computer.  
This function enables you to operate both the projector  
and computer only with the Remote Control Unit.  
One-Touch Auto PC Adjustment  
Incoming computer video signals are recognized and the  
best adjustment is automatically set by Auto PC  
Adjustment. No complicated setup is necessary and  
projection is always precise.  
Multilanguage Menu Display  
The Operation menu is displayed in: English, German,  
French, Italian, Spanish, Portuguese, Dutch, Swedish,  
Chinese, Korean or Japanese.  
Motor-driven Lens Shift  
ChristieNet (Optional)  
The projection lens can be moved up and down with the  
motor-driven lens shift function. This function makes it  
easy to project the image where you wish.  
Zoom and focus can be also adjusted with motor-driven  
operation.  
ChristieNet is an optional product to control and set up a  
projector via the network cable. By accessing to the  
connected projector using the web browser on your  
computer. It can be controlled and set up the projector  
remotely. Contact the sales dealer where you purchased  
this projector for optional parts.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
NAME OF EACH PART OF PROJECTOR  
FRONT OF CABINET  
TOP CONTROL PANEL  
AND INDICATORS  
PROJECTION LENS  
AIR INTAKE  
VENT  
INFRARED  
REMOTE RECEIVER  
LENS COVER  
SPEAKERS  
BACK OF CABINET  
EXHAUST VENT  
TERMINALS  
AND CONNECTORS  
INFRARED  
REMOTE RECEIVER  
POWER CORD  
CONNECTOR  
HOT AIR EXHAUSTED !  
Air blown from exhaust vent is hot. When  
using or installing a projector, following  
precautions should be taken.  
Do not put a flammable object near this vent.  
Keep rear grills at least 3(1 m) away from  
any object, especially heat-sensitive object.  
Do not touch this area, especially screws  
and metallic parts. This area will become  
hot while a projector is used.  
CARRYING  
HANDLE  
This projector detects internal temperature  
and automatically controls operating power  
of Cooling Fans.  
LAMP COVER  
When attaching the ChristieNet (optional part)  
to the projector, remove the these parts.  
Refer to the owner's manual in the optional  
ChristieNet.  
BOTTOM OF CABINET  
AIR INTAKE VENTS  
This projector is equipped with cooling fans for protection from  
overheating. Pay attention to following to ensure proper ventilation  
and avoid a possible risk of fire and malfunction.  
Do not cover vent slots.  
Keep side clear of any objects. Obstructions may block cooling  
air.  
ADJUSTABLE FEET  
AND  
FEET LOCK LATCHES  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
SETTING-UP PROJECTOR  
CONNECTING AC POWER CORD  
This projector uses nominal input voltages of 100-120 V or 200-240  
V AC. This projector automatically selects the correct input  
voltage. It is designed to work with single-phase power systems  
having a grounded neutral conductor. To reduce risk of electrical  
shock, do not plug into any other type of power system.  
Consult your authorized dealer or service station if you are not sure  
of the type of power supply used.  
Connect the projector with peripheral equipment before turning the  
projector on. (Refer to pages 11 ~ 13 for connection.)  
CAUTION  
For safety, unplug AC Power Cord when an appliance is not  
used.  
When this projector is connected to the outlet with an AC Power  
Cord, the appliance is in Stand-by Mode and consumes a little  
electric power.  
Connect the AC Power Cord (supplied) to the  
projector.  
The AC outlet must be near this equipment and must  
be easily accessible.  
CAUTION  
The AC Power Cord must meet the requirement of the country where you use the projector.  
Confirm the AC plug type with the chart below. The proper AC Power Cord must be used.  
If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.  
Projector side  
AC Outlet side  
For U.S.A. and Canada  
For Continental Europe  
Ground  
To POWER CORD  
CONNECTOR on the  
projector.  
To AC Outlet.  
(120 V AC)  
To AC Outlet.  
(200 - 240 V AC)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
LENS INSTALLATION  
Before setting up a projector, install Projection Lens on  
Projector.  
1. Before installation, check where a projector is used and  
prepare a suitable lens. For specifications of a Projection  
Lens, contact sales dealer where you purchased a projector.  
2. For installation, refer to installation manual in the optional  
lens.  
NOTE;  
COVER CAP  
When installing the lens, remove the cover cap in the  
projector.  
POSITIONING PROJECTOR  
This projector is designed to project on a flat projection  
surface.  
SCREEN  
ROOM LIGHT  
Brightness in a room has a great influence on picture  
quality. It is recommended to limit ambient lighting in  
order to provide best image.  
LENS SHIFT ADJUSTMENT  
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to  
provide projected image where you want. U/D ratio can be adjusted 10 : 0 ~ 1 : 1 (refer to figure below.). Refer  
to P 20 for operation.  
Highest (10 : 0)  
Lowest (1 : 1)  
1
1
10 : 0  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
ADJUSTABLE FEET  
Picture tilt and projection angle can be adjusted by  
rotating ADJUSTABLE FEET. Projection angle can be  
adjusted to 10.5 degrees.  
Lift front of a projector and pull FEET LOCK LATCHES  
on both sides of a projector.  
1
Release FEET LOCK LATCHES to lock ADJUSTABLE  
FEET and rotate ADJUSTABLE FEET to fine tune  
position and tilt.  
2
To shorten ADJUSTABLE FEET, lift front of a projector  
and pull and undo FEET LOCK LATCHES.  
3
Position and keystone distortion of image can be adjusted  
using Menu Operation. (Refer to P 20 and 35.)  
ADJUSTABLE FEET  
FEET LOCK  
LATCHES  
NOTE :  
THIS PROJECTOR SHOULD BE SET IN THE WAY  
INDICATED. PROJECTION LAMP MAY MALFUNCTION.  
MOVING PROJECTOR  
Use Carry Handle when moving a Projector.  
When moving a projector, replace lens cover and retract  
feet to prevent damage to lens and cabinet.  
When this projector is not in use for an extended period,  
put it into case (dust cover) supplied with this projector.  
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR  
Do not drop or bump a projector, otherwise damages or malfunctioning may result.  
When carrying a projector, use a suitable carrying case.  
Do not transport a projector by using a courier or transport service in an unsuitable transport case. This  
may cause damage to a projector. To transport a projector through a courier or transport service, consult  
your dealer for the best method.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
TERMINALS OF PROJECTOR  
This projector has input and output terminals on its back for connecting computers and video equipment. Refer to figures on  
pages 11 to 13 and connect properly.  
COMPUTER INPUT  
TERMINALS (DIGITAL/ANALOG)  
COMPUTER AUDIO  
INPUT (1 and 2) JACKS  
Connect the computer (digital/analog)  
output to one of these terminals.  
(Refer to P12.)  
Connect the audio output  
(stereo) from the computer  
to these jacks.  
R/C JACK  
When using the Wired/Wireless  
Remote Control Unit as a Wired  
Remote Control, connect the  
Wired Remote Control Unit to  
this jack with the Remote  
Control Cable (supplied).  
(Refer to P12.)  
INPUT 1  
USB CONNECTOR (Series B)  
ANALOG  
DIGITAL(DVI-D)  
R/C JACK  
When controlling the computer  
with the Remote Control Unit of  
the projector, connect the USB  
port of your personal computer  
to this terminal. (Refer to P12.)  
CONTROL PORT  
RESET  
USB  
AUDIO 1  
AUDIO 2  
CONTROL PORT CONNECTOR  
G
B
R
H/V  
V
When controlling the computer  
with the Remote Control Unit  
of the projector, connect the  
mouse port of your personal  
computer to this connector.  
(Refer to P12.)  
VIDEO/Y Cb/Pb  
Cr/Pr  
INPUT 2  
RESET BUTTON  
S–VIDEO  
VIDEO/Y Cb/Pb Cr/Pr  
R–AUDIO–L  
This projector uses a micro processor  
to control this unit, and occasionally  
this micro processor may malfunction  
and need to be reset. This can be  
done by pressing the RESET button  
with a pen, which will shut down and  
restart unit. Do not use the RESET  
function excessively.  
(
)
MONO  
INPUT 3  
Do not press this button. This button  
is used for our optional accessories.  
VIDEO INPUT JACKS  
AUDIO INPUT JACKS  
S-VIDEO INPUT JACK  
Connect the composite video Connect the audio output Connect the S-VIDEO  
output from video equipment to from video equipment to output from video  
5 BNC INPUT JACKS  
the VIDEO/Y jack or connect these jacks.  
the component video outputs to (Refer to P13.)  
the VIDEO/Y, Cb/Pb and Cr/Pr When the audio output is  
equipment to this  
jack. (Refer to P13.)  
Connect the component video  
output (Y, Cb, Cr or Y, Pb, Pr)  
from video equipment to  
VIDEO/Y, Cb/Pb and Cr/Pr  
jacks or connect computer  
output {5 BNC Type (Green,  
Blue, Red, Horiz. Sync and  
Vert. Sync.)} from computer  
to G, B, R, H/V and V jacks.  
(Refer to P12 and 13.)  
jacks. (Refer to P13.)  
monaural, connect it to  
the L (MONO) jack.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO COMPUTER  
Cables used for connection (= Cable or adapter is not supplied with this projector.)  
VGA Cable (HDB 15 pin)  
USB Cable ✽  
DVI-Digital Cable (for Single Link T.M.D.S.) ✽  
BNC Cable ✽  
MAC Adapter (When connecting to Macintosh computer)  
Audio Cables (RCA x 2 and Mini Plug (stereo) x 1) ✽  
Control Cable for PS/2 Port, Serial Port or ADB Port  
IBM-compatible computer or Macintosh computer (VGA / SVGA / XGA / SXGA)  
Desktop type  
Laptop type  
Monitor Output  
Monitor Output  
USB port Audio Output Serial port PS/2 port  
ADB port  
Control Cable  
for Serial Port  
Control Cable  
for PS/2 Port  
Control Cable  
for ADB Port  
USB  
Cable  
MAC Adapter  
Audio  
Cable ✽  
(stereo)  
Set slide switches  
according to chart  
below.  
Terminal  
Terminal  
DVI  
Cable ✽  
Terminal  
BNC  
Cable ✽  
VGA Cable  
Use one of these Control  
Cables corresponding with  
terminal of your computer.  
COMPUTER  
AUDIO IN 1 or 2  
USB  
COMPUTER IN ANALOG  
CONTROL  
PORT  
COMPUTER IN DIGITAL  
INPUT 1  
ANALOG  
DIGITAL(DVI-D)  
R/C JACK  
CONTRL PORT  
RESET  
USB  
AUDO  
1
AUDO  
2
G
B
R
H/V  
V
VIDEO/Y Cb/Pb  
Cr/Pr  
INPUT 2  
SVIDEO  
VIDEO/Y Cb/Pb Cr/Pr  
RAUDIOL  
(
)
MONO  
INPUT 3  
Terminals  
of the Projector  
MAC ADAPTER  
NOTE :  
When connecting the cable, the Power  
Cords of both the projector and the external  
equipment should be disconnected from the  
AC outlet. Turn the projector and peripheral  
equipment on before the computer is  
switched on.  
Set switches as shown in table  
below depending on RESOLU-  
TION MODE that you want to use  
before you turn on projector and  
computer.  
ON  
ON  
DIP  
1
2
3
4
5
6
OFF  
3
1
2
4
5
6
13" MODE (640 x 480)  
ON  
ON OFF OFF OFF OFF  
16" MODE (832 x 624) OFF ON OFF ON OFF OFF  
19" MODE (1024 x 768) OFF ON  
21" MODE (1152 x 870) ON ON  
ON OFF OFF OFF  
ON ON OFF OFF  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONNECTING PROJECTOR  
CONNECTING TO VIDEO EQUIPMENT  
Cables used for connection (= Cable is not supplied with this projector.)  
Video Cable (RCA x 1 or RCA x 3) ✽  
BNC Cable ✽  
S-VIDEO Cable ✽  
Audio Cable (RCA x 2) ✽  
Video Source (example)  
Component video output equipment.  
(such as DVD player or high-definition TV source.)  
Video Cassette Recorder  
Video Disc Player  
Composite Component Video Output  
Composite Component Video Output Audio Output  
Video Output  
(Y, Cb/Pb, Cr/Pr)  
S-VIDEO Output  
Video Output  
(Y, Cb/Pb, Cr/Pr)  
Video Cables  
(RCA x 1 or  
RCA x 3)  
Audio Cable  
(RCA x 2) ✽  
S-VIDEO  
Cable ✽  
BNC Cable ✽  
VIDEO  
Y - Cb/Pb - Cr/Pr VIDEO  
Y - Cb/Pb - Cr/Pr AUDIO IN  
S-VIDEO  
INPUT 1  
ANALOG  
DIGITAL(DVI-D)  
R/C JACK  
CONTROL PORT  
RESET  
USB  
AUDIO 1  
AUDIO 2  
G
B
R
H/V  
V
VIDEO/Y Cb/Pb  
Cr/Pr  
INPUT 2  
SVIDEO  
VIDEO/Y Cb/Pb Cr/Pr  
RAUDIOL  
(
)
MONO  
INPUT 3  
Terminals  
of the Projector  
NOTE :  
When connecting the cable, the Power Cords of  
both the projector and the external equipment  
should be disconnected from the AC outlet.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
OPERATION OF REMOTE CONTROL  
Left Side  
LASER POINTER INDICATOR  
POWER ON-OFF BUTTON  
Used to turn projector on or  
off. (P19)  
Lights red while laser beam  
is emitted from Laser Light  
Window.  
ON-OFF  
ZOOM FOCUS  
VOLUME  
INPUT BUTTON  
Used to select input source.  
(P22)  
D.ZOOM  
MUTE  
MENU  
INPUT  
MENU BUTTON  
POINT BUTTON  
Used to select MENU  
operation. (P17, 18)  
Used to move a pointer on ON-  
SCREEN MENU, adjust each  
item, or pan image in DIGITAL  
ZOOM +/mode. (P29)  
It is also used as a PC mouse  
in Wireless Mouse Operation.  
(P37)  
SELECT BUTTON  
Used to execute item  
selected, or to expand  
or compress image in  
DIGITAL ZOOM +/–  
mode. (P29)  
It is also used as a PC  
mouse in Wireless  
Mouse Operation. (P37)  
When pressing center of this  
button, it works as SELECT  
button.  
ALL-OFF SWITCH  
LASER  
When using Remote Control Unit,  
turn this switch to ON.And turn it  
to ALL OFFwhen it is not used.  
KEYSTONE  
NO SHOW  
RIGHT CLICK BUTTON  
LENS SHIFT  
Used as a PC mouse in  
Wireless Mouse Operation.  
(P37)  
FREEZE  
LASER BUTTON  
AUTO PC ADJ.  
P-TIMER  
IMAGE  
Used to operate Laser Pointer  
Function. Laser beam is  
emitted while pressing this  
button within 1 minute.  
When using this Laser Pointer  
for more than 1 minute, release  
LASER button and press it  
again.  
P-TIMER BUTTON  
Used to operate P-TIMER  
function. (P21)  
LASER POINTER FUNCTION  
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is  
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,  
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being  
emitted.  
Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other  
people. Three marks bellow are caution labels for laser beam.  
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result  
hazardous radiation exposure.  
These caution labels are put on remote control.  
LASER POINTER INDICATOR  
Laser Light Window  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
Operating Range  
ON-OFF  
Point Remote Control Unit toward  
projector (Receiver Window)  
whenever pressing any button.  
Maximum operating range for  
Remote Control Unit is about 16.4’  
(5m) and 60° in front and rear of a  
projector.  
ZOOM BUTTON  
Used to adjust zoom.  
(P20)  
VOLUME BUTTON  
Used to adjust volume.  
(P21)  
ZOOM FOCUS  
VOLUME  
FOCUS BUTTON  
Used to adjust focus.  
(P20)  
D.ZOOM  
MUTE  
MENU  
INPUT  
D.ZOOM BUTTON  
Used to select DIGITAL  
ZOOM +/mode and  
resize image. (P29)  
MUTE BUTTON  
60°  
Used to mute sound.(P21)  
KEYSTONE BUTTON  
Used to correct  
keystone distortion.  
(P20, 35)  
16.4’  
(5 m)  
LASER  
KEYSTONE  
NO SHOW  
FREEZE BUTTON  
Used to freeze picture.  
(P21)  
NO SHOW BUTTON  
Used to turn picture off.  
(P21)  
LENS SHIFT  
FREEZE  
IMAGE BUTTON  
Used to select image  
level. (P27, 32)  
AUTO PC ADJ.  
P-TIMER  
IMAGE  
AUTO PC ADJ. BUTTON  
Use to operate AUTO PC  
Adjustment function. (P23)  
16.4’  
(5 m)  
LENS SHIFT BUTTON  
Used to select LENS  
SHIFT function. (P20)  
WIRED REMOTE JACK  
60°  
When using as Wired  
Remote Control, connect  
Remote Control Cable to  
this jack.  
Battery installation is  
required when using as  
Wired Remote Control.  
Remote Control Batteries Installation  
Remove battery  
compartment lid.  
Slide batteries into  
compartment.  
Replace compartment lid.  
1
2
3
Two AA size batteries  
Press lid down-  
ward and slide it.  
For correct polarity (+ and  
), be sure battery  
terminals are in contact  
with pins in compartment.  
To insure safe operation, please observe following precautions :  
Use (2) AA, UM3 or R06 type alkaline batteries.  
Replace two batteries at same time.  
Do not use a new battery with an used battery.  
Avoid contact with water or liquid.  
Do not expose Remote Control Unit to moisture, or heat.  
Do not drop Remote Control Unit.  
If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.  
Danger of explosion if battery is incorrectly replaced.  
Dispose of used batteries according to batteries manufacturers instructions and local rules.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
TOP CONTROL PANEL AND INDICATORS  
This projector has CONTROL BUTTONS (TOP CONTROL PANEL) and INDICATORS on its top.  
LAMP REPLACE INDICATOR  
WARNING TEMP. INDICATOR  
READY INDICATOR  
LAMP INDICATOR  
Turns yellow when the  
life of the projection  
lamp draws to an end.  
(P39)  
Flashes red when  
Lights green when the  
projector is ready to be  
Becomes dim when the  
projector is turned on.  
And bright when the  
projector is in stand-by  
mode.  
internal  
projector  
temperature is too  
high. (P38)  
turned on.  
And it  
flashes green in Power  
Management mode.  
(P36)  
POWER ONOFF BUTTON  
Used to turn the projector  
on or off. (P19)  
MENU BUTTON  
Used to open or close  
MENU operation. (P17,  
18)  
INPUT BUTTON  
Used to select the input  
source. (P22, 30)  
ZOOM BUTTON  
Used to adjust zoom.  
(P20)  
FOCUS BUTTON  
Used to adjust focus.  
(P20)  
AUTO PC ADJ. BUTTON  
LENS SHIFT BUTTON  
Used to operate AUTO PC  
Adjustment function. (P23)  
Used to select LENS  
SHIFT function. (P20)  
IMAGE BUTTON  
Used to select image  
level. (P27, 32)  
SELECT BUTTON  
POINT (VOLUME + / ) BUTTONS  
Used to execute the item  
selected. It is also used  
to expand/compress the  
image in DIGITAL ZOOM  
mode. (P29)  
Used to select an item or adjust  
value in ON-SCREEN MENU. They  
are also used to pan the image in  
DIGITAL ZOOM +/mode. (P29)  
POINT LEFT/RIGHT buttons are  
also used as VOLUME +/buttons.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING ON-SCREEN MENU  
HOW TO OPERATE ON-SCREEN MENU  
WIRELESS REMOTE CONTROL  
You can control and adjust this projector through the ON-SCREEN  
MENU. Refer to the following pages to operate each adjustment  
on the ON-SCREEN MENU.  
POINT BUTTON  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
1 DISPLAY MENU  
Press MENU button to display ON-SCREEN MENU.  
2 MOVING POINTER  
SELECT BUTTON  
Used to select item.  
Move the pointer (see below) or adjust the value of the item by  
pressing POINT button(s) on Top control panel or on Remote  
Control Unit.  
Pointer is the icon on ON-SCREEN MENU to select the item.  
See the figures on the section "FLOW OF ON-SCREEN MENU  
OPERATION" below.  
TOP CONTROL PANEL  
POINT BUTTONS  
Used to move the  
Pointer UP/ DOWN/  
RIGHT/ LEFT.  
3 SELECT ITEM  
Select the item or set selected function by pressing SELECT  
button.  
SELECT BUTTON  
Used to select the item.  
FLOW OF ON-SCREEN MENU OPERATION  
MENU BAR  
MENU ICON  
Display ON-SCREEN MENU  
Press MENU button to display ON-SCREEN MENU (MENU  
BAR). A red frame is POINTER.  
1
POINTER  
(red frame)  
POINTER (red frame)  
Select Menu to be adjusted  
Press the POINT DOWN but-  
ton to move POINTER.  
Move POINTER (red frame) to MENU ICON that you want to  
2
select by pressing the POINT RIGHT / LEFT buttons.  
ITEM  
Control or adjust item through ON-SCREEN MENU  
Press the POINT DOWN button and move POINTER (red  
frame or red arrow) to ITEM that you want to adjust, and then  
press SELECT button to show ITEM DATA.  
3
SELECT  
BUTTON  
Adjust ITEM DATA by pressing the POINT RIGHT / LEFT  
buttons.  
Refer to the following pages for details of respective  
adjustments.  
4
ITEM DATA  
Press the POINT LEFT/RIGHT  
buttons to adjust value or set  
function.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
MENU BAR  
FOR PC SOURCE  
Press MENU BUTTON while connecting to PC input source.  
IMAGE SELECT MENU  
SCREEN MENU  
SETTING MENU  
Used to select  
Used to adjust size  
of image. [Normal  
/True/Wide/Digital  
zoom +/]  
Used to change  
settings of projector  
or reset Lamp  
Replace Counter.  
(Refer to P35-37)  
GUIDE WINDOW  
PC SYSTEM MENU  
image level among  
Standard, Real  
and Image 1 ~ 4.  
(Refer to P27)  
Shows selected  
item of ON-  
SCREEN MENU.  
Used to select  
computer system.  
(Refer to P22, 23)  
(Refer to P29)  
INPUT MENU  
PC ADJUST MENU  
IMAGE ADJUST MENU  
SOUND MENU  
Used to select  
Used to adjust  
parameters to  
match with input  
signal format.  
Used to adjust  
Used to adjust  
volume or mute  
sound.  
input source (Input  
1, Input 2 or Input  
3). (Refer to P22)  
computer image.  
[Contrast/Brightness/  
White Balance  
(Refer to P21)  
(Refer to P23-25)  
(R/G/B)/Gamma]  
(Refer to P28)  
FOR VIDEO SOURCE  
Press MENU BUTTON while connecting to VIDEO input source.  
INPUT MENU  
Used to select  
input source  
(Input 1, Input 2  
or Input 3).  
IMAGE SELECT MENU  
SCREEN MENU  
Used to select image  
level among  
Standard, Cinema  
and Image 1 ~ 4.  
(Refer to P32)  
Used to set size of  
image to Normal  
or Wide.  
(Refer to P30)  
(Refer to P34)  
AV SYSTEM MENU  
IMAGE ADJUST MENU  
Same function as  
Menu for PC source.  
Same function as  
Menu for PC source.  
Used to select  
system of selected  
video source.  
Used to adjust picture image.  
[Contrast/Brightness/Color/Tint/  
White balance (R/G/B)/  
(Refer to P31)  
Sharpness/Gamma/Noise  
Reduction/Progressive]  
(Refer to P33, 34)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE OPERATION  
TURNING ON / OFF PROJECTOR  
TURNING ON PROJECTOR  
Complete peripheral connections (with Computer, VCR, etc.)  
before turning on projector. (Refer to "CONNECTING TO  
PROJECTOR" on pages 11~13 for connecting that equipment.)  
Input position and  
Lamp mode status  
1
2
Input 1  
Connect a projector's AC Power Cord into an AC outlet. LAMP  
Indicator lights RED, and READY Indicator lights GREEN.  
30  
NOTE : When On startfunction is ON, this projector is turned  
on automatically by connecting AC Power Cord to an  
AC outlet. (Refer to pages 35, 36.)  
Press POWER ON-OFF button on Top control panel or on  
Remote Control Unit to ON. LAMP Indicator dims, and Cooling  
Fans start to operate. Preparation Display appears on a screen  
and count-down starts. Signal from PC or Video source appears  
after 30 seconds.  
3
Preparation Display disappears after 30 seconds.  
Current Input position and Lamp mode status are also displayed  
on screen for 5 seconds. (Refer to "LAMP MODE" on page 36.)  
TURNING OFF PROJECTOR  
Press POWER ON-OFF button on Top control panel or on  
Remote Control Unit, and a message "Power off?" appears on a  
screen.  
1
2
Press POWER ON-OFF button again to turn off projector. LAMP  
Indicator lights bright and READY Indicator turns off. After  
projector is turned off, Cooling Fans operate (for 90 seconds).  
During this "Cooling Down" period, this appliance can not be  
turned on.  
Power off?  
Message disappears after 4 seconds.  
When projector has cooled down, READY Indicator lights  
GREEN again and you can turn projector on. After cooling down  
completely, disconnect AC Power Cord.  
3
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN  
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE  
TURNING IT OFF.  
When Power Managementfunction is ON, projector detects signal interruption and turns off Projection Lamp automatically.  
Refer to Power Managementon page 35.  
When WARNING TEMP. Indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on  
projector again.  
When WARNING TEMP. Indicator continues to flash, follow procedures below:  
1. Press POWER ON-OFF button to turn a projector off and disconnect AC Power Cord from an AC outlet.  
2. Check Air Filters for dust accumulation.  
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 38.)  
4. Turn a projector on again.  
If WARNING TEMP. Indicator should still continue to flash, contact sales dealer where you purchased this projector or  
service center.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
ADJUSTING SCREEN  
ZOOM ADJUSTMENT  
Press ZOOM button on Top control panel or ZOOM /button  
on Remote Control Unit. Message Zoomis displayed.  
1
2
Press ZOOM button or the POINT UP button to make image  
larger, and press ZOOM button or the POINT DOWN button  
to make image smaller.  
Zoom  
Message disappears after 4 seconds.  
FOCUS ADJUSTMENT  
Press FOCUS button on Top control panel or FOCUS /✽  
button on Remote Control Unit. Message Focusis displayed.  
1
2
Adjust focus of image by pressing FOCUS /button or the  
POINT UP/DOWN button(s) .  
Focus  
NOTE;  
Focus adjustment may not function properly if the image is  
corrected by KEYSTONE adjustment.  
Message disappears after 4 seconds.  
LENS SHIFT ADJUSTMENT  
Press LENS SHIFT button on Top control panel or LENS SHIFT  
/button on Remote Control Unit. Message Lens shiftis  
displayed.  
1
2
Press the POINT UP button or LENS SHIFT button to move  
image up, press the POINT DOWN or LENS SHIFT button to  
move image down.  
Lens shift  
KEYSTONE ADJUSTMENT  
If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment.  
Press KEYSTONE button on Remote Control Unit or select  
Keystone on SETTING menu. (Refer to page 35.) Keystone  
dialog box appears.  
1
Correct keystone distortion by pressing the POINT  
UP/DOWN/LEFT/RIGHT button(s). Press the POINT UP button  
to reduce the upper part of the image, and press the POINT  
DOWN button to reduce the lower part. Press the POINT LEFT  
button to reduce the left part, and press the POINT RIGHT  
button to reduce the right part.  
2
Arrows are white in no correction.  
Arrow(s) of direction being corrected turn(s) red.  
Arrow(s) disappear(s) at the maximum  
correction.  
Reduce the lower width with  
the POINT DOWN button.  
Reduce the upper width  
with the POINT UP button.  
Reduce the left part with  
the POINT LEFT button.  
Reduce the right part with  
the POINT RIGHT button.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BASIC OPERATION  
PICTURE FREEZE FUNCTION  
Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE  
button again or press any other button except the POINT, SELECT, RIGHT CLICK and LASER buttons.  
NO SHOW FUNCTION  
Press NO SHOW button on Remote Control Unit to black out the  
No show  
image. To restore to normal, press NO SHOW button again or press  
any other button except the POINT, SELECT, RIGHT CLICK and  
LASER buttons.  
The message disappears after 4 seconds.  
P-TIMER FUNCTION  
Press P-TIMER button on Remote Control unit. The timer display 00 :  
00appears on the screen and the timer starts to count time (00 : 00 ~  
59 : 59).  
To stop P-TIMER display, press P-TIMER button. And then, press P-  
TIMER button again to cancel P-TIMER function.  
SOUND ADJUSTMENT  
Indicates roughly level of  
volume.  
DIRECT OPERATION  
Volume  
Press VOLUME (+/) button(s) on Top control panel or on Remote  
Control Unit to adjust volume. Volume dialog box appears on screen  
for a few seconds.  
(+) button to increase volume, and () button to decrease.  
Mute  
Press the MUTE button on Remote Control Unit to disable sound. To  
restore sound to its previous level, press MUTE button again or press  
Volume (+/) button(s).  
Press the MUTE button to set  
Mute function On or Off.  
Display disappears after 4 seconds.  
MENU OPERATION  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT buttons to move the red frame pointer  
to the SOUND Menu icon.  
1
SOUND MENU  
Press the POINT DOWN button to move the red frame pointer to  
the item that you want to select, and then press SELECT button.  
2
SOUND Menu icon  
Volume  
Indicates roughly  
level of volume.  
To increase volume, press the POINT RIGHT button, and press the  
POINT LEFT button for decreasing.  
Close SOUND Menu.  
Mute  
Press the POINT LEFT/RIGHT button(s) to disable sound. The dialog  
box display will change to Onand the sound will be disabled. To  
restore sound to its previous level, press the POINT LEFT/RIGHT  
button(s) again.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
SELECTING INPUT SOURCE  
INPUT button  
Input 1  
DIRECT OPERATION  
Select the appropriate input signal by pressing the INPUT button on  
the Top control panel or on the Remote Control Unit.  
If projector cannot reproduce proper image, select correct input source  
through MENU OPERATION (see below).  
Input 2  
Input 3  
MENU OPERATION  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT buttons to select Input and press  
1
SELECT button.  
appear.  
Menu will  
Another dialog box INPUT SELECT  
INPUT Menu icon  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move arrow to INPUT source that you want to select,  
and then press SELECT button.  
2
SELECTING COMPUTER SYSTEM  
WHEN SELECTING INPUT 1 (COMPUTER INPUT TERMINALS )  
INPUT MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
INPUT Menu icon.  
1
2
3
INPUT Menu icon  
Press the POINT DOWN button to move the red arrow pointer to  
Input 1 and then press SELECT button. Source Select Menu will  
appear.  
Move the pointer (red arrow)  
to Input 1 and press SELECT  
button.  
Move the pointer to either Digital or Analog and then press  
SELECT button.  
Input 1  
Source Select Menu  
When your computer is connected to COMPUTER  
INPUT (DIGITAL) terminal, select RGB (Digital).  
Move the pointer to Digital or  
Analog and press SELECT  
button.  
Digital  
When your computer is connected to COMPUTER INPUT  
(ANALOG) terminal, select RGB (Analog).  
Analog  
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )  
When connecting a computer output [5 BNC Type (Green, Blue, Red,  
Horiz. Sync and Vert. Sync.)] from a computer to G, B, R, H/HV and V  
jacks.  
INPUT MENU  
INPUT Menu icon  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
INPUT Menu icon.  
1
Move the pointer (red arrow)  
to Input 2 and press SELECT  
button.  
Press the POINT DOWN button to move the red arrow pointer to  
Input 2 and then press SELECT button. Source Select Menu will  
appear.  
Input 2  
2
Source Select Menu  
Press the POINT DOWN button and a red-arrow icon will  
appear. Move arrow to "RGB", and then press SELECT button.  
Move the pointer to RGB  
and press SELECT button.  
3
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
AUTOMATIC MULTI-SCAN SYSTEM  
This projector automatically detects different types of computer resolutions such as VGA, SVGA, XGA or SXGA (refer to  
COMPATIBLE COMPUTER SPECIFICATIONSon page 26). When selecting Computer, this projector automatically  
detects incoming signal and projects proper image without any special setting. (Some computers need setting manually.)  
Note : Projector may display one of following messages.  
When projector can not recognize connected signal as  
PC system provided in this projector, Auto PC Adjustment  
function operates to adjust projector and the message  
Autois displayed on SYSTEM Menu icon.  
PC SYSTEM MENU  
Auto  
When image is not provided properly, manual adjustment  
is required. (Refer to P24 and 25.)  
PC SYSTEM Menu icon  
Displays system being  
selected.  
There is no signal input from computer. Make sure  
connection of computer and the projector is set correctly.  
(Refer to TROUBLESHOOTING on page 40.)  
––––  
D-VGA, D-SVGA or D-XGA  
When digital computer signal is received on DVI terminal,  
above message is displayed on PC SYSTEM Menu icon.  
PC SYSTEM MENU  
SELECT COMPUTER SYSTEM MANUALLY  
This projector automatically selects PC system among those provided  
in this projector and PC system can be also selected manually.  
PC SYSTEM Menu icon  
Displays system being selected.  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT buttons to move the red frame pointer  
to PC SYSTEM Menu icon.  
1
Systems on this dialog box can  
be selected.  
Press the POINT DOWN button to move the red arrow pointer to  
Custom Mode (1~5) set in PC  
ADJUST Menu. (P24, 25)  
2
the system that you want to set, and then press  
SELECT button.  
PC ADJUSTMENT  
AUTO PC ADJUSTMENT  
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your  
computer. Auto PC Adjustment function can be operated as follows.  
Auto PC Adj.  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
PC ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press the POINT DOWN button to move the red frame pointer to  
AUTO PC Adj. icon and then press SELECT button twice.  
This Auto PC Adjustment can be also executed by pressing  
AUTO PC ADJ. button on the Top control panel or on the  
Remote Control Unit.  
PC ADJUST Menu icon  
Move the red frame pointer to AUTO PC  
Adj. icon and press SELECT button.  
Store adjustment parameters.  
Adjustment parameters from Auto PC Adjustment can be memorized  
in this projector. Once parameters are memorized, setting can be  
done just by selecting Mode in PC SYSTEM Menu (P23). Refer to  
step 3 of MANUAL PC ADJUSTMENT section (P25).  
NOTE  
Fine sync, Total dots and Picture Position of some computers can not be fully adjusted with this Auto PC Adjustment  
function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page  
24, 25.)  
Auto PC Adjustment function can not be operated in Digital Signal input on DVI terminal and when RGB, 720p (HDTV),  
1035i (HDTV)or 1080i (HDTV)is selected on PC SYSTEM Menu.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
MANUAL PC ADJUSTMENT  
This projector can automatically detect display signals from most personal computers currently distributed. However, some  
computers employ special signal formats which are different from the standard ones and may not be detected by the Multi-  
Scan system of this projector. If this happens, the projector can not reproduce a proper image and the image may be  
recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture.  
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special  
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This  
enables you to recall the setting for a specific computer whenever you use it.  
Note : This PC ADJUST Menu can not be operated when a digital signal is input to the DVI terminal or RGBis selected on  
PC SYSTEM MENU (P23).  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
PC ADJUST Menu icon.  
PC ADJUST MENU  
1
2
Press the POINT DOWN button to move the red frame pointer to  
the item that you want to adjust and then press SELECT button.  
Adjustment dialog box will appear. Press the POINT  
LEFT/RIGHT button to adjust value.  
PC ADJUST Menu icon  
Move the red frame icon to the item and  
press SELECT button.  
Fine sync  
Adjusts an image as necessary to eliminate flicker from display.  
Press the POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)  
Shows status  
(Stored / Free) of the  
selected Mode.  
Total dots  
Selected Mode  
The number of total dots in one horizontal period. Press the POINT  
LEFT/RIGHT button(s) and adjust number to match your PC image.  
Horizontal  
Adjusts horizontal picture position. Press the POINT LEFT/RIGHT  
button(s) to adjust position.  
Press the POINT LEFT/RIGHT  
button to adjust the value.  
Vertical  
Adjusts vertical picture position. Press the POINT LEFT/RIGHT  
button(s) to adjust position.  
Press SELECT button at this icon to  
adjust Clamp,” “Display area (H/V)or  
set Full screen.”  
Current mode  
Press SELECT button to show information of computer selected.  
Clamp  
Current mode  
Adjusts clamp position. When image has a dark bar(s), try this  
adjustment.  
Press SELECT button at  
Current mode icon to show  
information of computer  
connected.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
Display area  
Selects area displayed with this projector. Select the resolution in the  
Display area dialog box.  
Press SELECT button at  
Display area icon and Display  
area dialog box appears.  
Display area H  
Adjustment of horizontal area displayed with this projector. Press the  
POINT LEFT/RIGHT button(s) to decrease/increase value and then  
press SELECT button.  
Display area  
Display area V  
Adjustment of vertical area displayed with this projector. Press the  
POINT LEFT/RIGHT button(s) to decrease/increase value and then  
press SELECT button.  
Press the POINT LEFT  
/RIGHT button(s) to  
adjust value and then  
press SELECT button.  
Full screen  
Press the POINT LEFT/RIGHT button(s) to switch Full screen  
function to Onor Off.Set Onto resize image with 4 x 3 aspect  
ratio to fit screen.  
NOTE : Fine sync., Total dots, Display area (H/V) and Full screen  
can not be adjusted when 1035i (HDTV)or 1080i (HDTV)”  
is selected on PC SYSTEM Menu (P23).  
To store adjustment data.  
This Mode has parameters being stored.  
Store  
3
To store adjustment parameters, move the red frame pointer to  
Store icon and then press SELECT button. Move the red arrow  
pointer to any of Mode 1 to 5 that you want to store and then  
press SELECT button.  
Mode free  
To clear adjustment parameters previously set, move the red  
frame pointer to Mode free icon and then SELECT button. Move  
the red arrow pointer to Mode that you want to clear and then  
press SELECT button.  
Vacant Mode  
Store icon  
Shows values of Total dots,”  
Horizontal,” “Vertical,” “Display  
area H,and Display area V.”  
Other icons operate as follows.  
Reset  
Reset all adjusted parameters on the adjustment dialog box to  
previous settings.  
To clear adjustment data.  
Quit  
Closes PC ADJUST MENU.  
Close this dialog box.  
Mode free icon  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
COMPATIBLE COMPUTER SPECIFICATIONS  
This projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 160  
MHz of Dot Clock.  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
VGA 1  
VGA 2  
VGA 3  
VGA 4  
VGA 5  
VGA 6  
VGA 7  
MAC LC13  
MAC 13  
RGB  
640 x 480  
720 x 400  
640 x 400  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
31.47  
31.47  
31.47  
37.86  
37.86  
37.50  
43.269  
34.97  
35.00  
15.734  
15.625  
35.156  
37.88  
46.875  
53.674  
48.08  
37.90  
34.50  
38.00  
38.60  
32.70  
38.00  
49.72  
48.36  
68.677  
60.023  
56.47  
60.31  
48.50  
44.00  
63.48  
36.00  
59.88  
70.09  
70.09  
74.38  
72.81  
75.00  
85.00  
66.60  
66.67  
30  
XGA 10  
XGA 11  
XGA 12  
XGA 13  
XGA 14  
XGA15  
1024 x 768  
1024 x 768  
62.04  
61.00  
35.522  
46.90  
47.00  
58.03  
60.24  
68.68  
64.20  
62.50  
63.90  
63.34  
63.74  
71.69  
81.13  
63.98  
79.976  
60.00  
61.20  
71.40  
50.00  
50.00  
63.37  
76.97  
61.85  
46.43  
63.79  
75.00  
80.00  
45.00  
33.75  
33.75  
77.07  
75.70  
43.48  
58.20  
58.30  
72.0  
1024 x 768  
(Interlace)  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1152 x 870  
1152 x 864  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 1024  
1280 x 960  
1152 x 900  
1152 x 900  
MAC 19  
MAC 21  
SXGA 1  
SXGA 2  
SXGA 3  
SXGA 4  
SXGA 5  
SXGA 6  
SXGA 7  
SXGA 8  
SXGA 9  
SXGA 10  
SXGA 11  
SXGA 12  
SXGA 13  
SXGA 14  
75.08  
75.06  
70.40  
58.60  
60.00  
59.98  
60.01  
67.19  
76.107  
60.02  
75.025  
60.00  
65.20  
75.60  
43.00  
47.00  
60.01  
72.00  
66.00  
43.35  
60.18  
75.08  
75.08  
60.00  
30.00  
30.00  
––––––––  
(Interlace)  
––––––––  
(Interlace)  
RGB  
25  
SVGA 1  
SVGA 2  
SVGA 3  
SVGA 4  
SVGA 5  
SVGA 6  
SVGA 7  
SVGA 8  
SVGA 9  
SVGA 10  
SVGA 11  
MAC 16  
XGA 1  
XGA 2  
XGA 3  
XGA 4  
XGA 5  
XGA 6  
XGA 7  
XGA 8  
XGA 9  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
56.25  
60.32  
75.00  
85.06  
72.19  
61.03  
55.38  
60.51  
60.31  
51.09  
60.51  
74.55  
60.00  
84.997  
75.03  
70.07  
74.92  
60.02  
54.58  
79.35  
43.59  
1280 x 1024  
(Interlace)  
1280 x 1024  
(Interlace)  
SXGA 15 1280 x 1024  
SXGA 16 1280 x 1024  
SXGA 17  
SXGA 18  
1152 x 900  
1280 x 1024  
(Interlace)  
SXGA 19 1280 x 1024  
MAC  
MAC  
720p (HDTV)  
1035i (HDTV)  
1080i (HDTV)  
1280 x 960  
1280 x 1024  
––––––––  
(Progressive)  
––––––––  
(Interlace)  
1024 x 768  
(Interlace)  
––––––––  
(Interlace)  
When an input signal is digital from the DVI terminal, refer to chart below.  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
ON-SCREEN  
DISPLAY  
H-Freq.  
(kHz)  
V-Freq.  
(Hz)  
RESOLUTION  
RESOLUTION  
D-VGA  
640 x 480  
800 x 600  
31.469  
37.879  
59.940  
60.317  
D-XGA  
1024 x 768  
48.363  
60.004  
D-SVGA  
NOTE : Specifications are subject to change without notice.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Real, Image 1, Image 2, Image 3  
IMAGE button  
and Image 4 by pressing IMAGE button on Top control panel or on  
Remote Control Unit.  
Standard  
Real  
Standard  
Normal picture level preset on this projector.  
Image 1  
Image 2  
Image 3  
Image 4  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P28).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press the POINT DOWN button to move the red frame pointer to  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture level preset on this projector.  
Move the red frame icon to level  
and press SELECT button.  
Real  
Picture level with improved halftone for graphics.  
IMAGE 1~4  
Level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P28).  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT buttons to move the red frame pointer  
to IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press the POINT DOWN button to move the red frame pointer to  
the item that you want to adjust and then press SELECT button.  
The level of each item is displayed. Adjust each level by  
pressing the POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move the red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press the POINT LEFT button to decrease contrast, and the POINT  
RIGHT button to increase contrast. (From 0 to 63.)  
Brightness  
Press the POINT LEFT button to decrease brightness, and the  
POINT RIGHT button to increase brightness. (From 0 to 63.)  
Selected Image level  
White balance (Red)  
Press the POINT LEFT button to lighten red tone and the POINT  
RIGHT button to enhance red tone. (From 0 to 63.)  
White balance (Green)  
Press the POINT LEFT/RIGHT but-  
tons to adjust value.  
Press the POINT LEFT button to lighten green tone and the POINT  
RIGHT button to enhance green tone. (From 0 to 63.)  
White balance (Blue)  
Press the POINT LEFT button to lighten blue tone and the POINT  
RIGHT button to enhance blue tone. (From 0 to 63.)  
Store icon  
Press SELECT button at this icon to  
store adjustment.  
Gamma  
Press either the POINT LEFT button or the POINT RIGHT button to  
obtain better balance of contrast. (From 0 to 15.)  
Store  
3
To store manually preset image, move the red frame pointer to  
Store icon and press SELECT button. Image Level Menu will  
appear. Move the red frame pointer to Image 1 to 4 where you  
want to set and then press SELECT button.  
Image Level Menu  
Other icons operate as follows.  
Move the red frame pointer to  
any of Image 1 to 4 where you  
want to set and then press  
SELECT button.  
Reset  
Reset all adjustment to previous settings.  
Quit  
Closes IMAGE MENU.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPUTER INPUT  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen adjustment function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button(s) to move the red frame pointer  
to SCREEN Menu icon.  
SCREEN MENU  
1
2
Press the POINT DOWN button and move the red frame pointer  
to the function that you want to select and then press SELECT  
button.  
SCREEN Menu icon  
Move the red frame to the function and  
press SELECT button.  
Normal  
Provides image to fit screen size.  
True  
Provides image in its original size. When original image size is larger  
than screen size (1024 x 768), this projector enters Digital zoom +”  
mode automatically.  
NOTE  
True and Digital zoom +/can not be operated  
when RGB, 1035i (HDTV)or 1080i (HDTV)is  
selected on PC SYSTEM Menu (P23).  
Wide  
Wide can not be selected when 720p (HDTV),  
1035i (HDTV)or 1080i (HDTV)is selected on  
PC SYSTEM Menu (P23).  
Provides image to fit wide video aspect ratio (16 : 9) by expanding  
image width uniformly. This function can be used for providing a  
squeezed video signal at 16 : 9.  
This projector can not display any resolution higher  
than 1280 X 1024. If your computers screen  
resolution is higher than 1280 X 1024, reset  
resolution to lower before connecting projector.  
Digital zoom +  
When Digital zoom + is selected, ON-SCREEN MENU disappears  
and the message D. Zoom +is displayed. Press SELECT button to  
expand image size. And press the POINT UP/DOWN/LEFT/RIGHT  
button(s) to pan the image. The panning function can work only when  
the image is larger than the screen size.  
A projected image can be also expanded by pressing D.ZOOM ✽  
button on Remote Control Unit.  
Image data in other than XGA (1024 x 768) is  
modified to fit screen size in initial mode.  
Panning function may not operate properly if  
computer system prepared on PC ADJUST Menu  
is used.  
Digital Zoom –  
When Digital zoom is selected, ON-SCREEN MENU disappears  
and the message D. Zoom –” is displayed. Press SELECT button to  
compress image size.  
A projected image can be also compressed by pressing D.ZOOM ✽  
button on Remote Control Unit.  
To cancel Digital Zoom +/mode, press any button except D.ZOOM  
/, SELECT, POINT and AUTO PC ADJ. buttons.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING INPUT SOURCE  
WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )  
When connecting to those equipment, select a type of Video  
source in SOURCE SELECT Menu.  
INPUT MENU  
INPUT Menu icon  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
INPUT Menu icon.  
1
Move the pointer (red arrow)  
to Input 2 and press SELECT  
button.  
Press the POINT DOWN button to move the red arrow pointer to  
Input 2 and then press SELECT button. Source Select Menu will  
appear.  
2
Input 2  
Source Select Menu  
Move the pointer to Video or  
Y, Pb/Cb, Pr/Cr and press  
SELECT button.  
Move the pointer to source that you want to select and then  
press SELECT button.  
3
When video input signal is connected to VIDEO jack,  
select Video.  
Video  
When video input signal is connected to Y-Pb/Cb-  
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y,Pb/Cb,Pr/Cr  
WHEN SELECTING INPUT 3 (AV TERMINALS )  
INPUT MENU  
When connecting to those equipment, select a type of Video  
source in SOURCE SELECT (VIDEO) Menu.  
INPUT Menu icon  
Press MENU button and ON-SCREEN MENU will appear. Press  
1
the POINT LEFT/RIGHT button to move the red frame pointer to  
INPUT Menu icon.  
Move the pointer (red arrow)  
to Input 3 and press SELECT  
button.  
Press the POINT DOWN button to move the red arrow pointer to  
Input 3 and then press SELECT button. Source Select Menu will  
appear.  
2
Input 3  
Source Select Menu (VIDEO)  
Move the pointer to source  
and press SELECT button.  
Move the pointer to source that you want to select and then  
press SELECT button.  
3
When video input signal is connected to VIDEO jack,  
select Video.  
Video  
When video input signal is connected to Y-Pb/Cb-  
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.  
Y,Pb/Cb,Pr/Cr  
When video input signal is connected to S-VIDEO jack,  
select S-Video.  
S-Video  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
SELECTING VIDEO SYSTEM  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT buttons to move the red frame pointer  
to AV SYSTEM Menu icon.  
1
2
Press the POINT DOWN button to move the red arrow pointer to  
system that you want to select and then press SELECT button.  
VIDEO JACK OR S-VIDEO JACK  
AV SYSTEM MENU (VIDEO OR S-VIDEO)  
Auto  
Projector automatically detects incoming Video system, and adjusts  
itself to optimize its performance.  
When Video System is PAL-M or PAL-N, select system manually first.  
AV SYSTEM Menu icon  
This box indicates system  
being selected.  
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N  
If projector can not reproduce proper video image, it is necessary to  
select a specific broadcast signal format among PAL, SECAM, NTSC,  
NTSC 4.43, PAL-M, and PAL-N.  
Move the pointer to  
system and press  
SELECT button.  
Y, Pb/Cb, Pr/Cr JACKS  
AV SYSTEM MENU (COMPONENT VIDEO)  
Auto  
Projector automatically detects incoming Video signal, and adjusts  
itself to optimize its performance.  
When Video System is 1035i or 1080i, select system manually first.  
AV SYSTEM Menu icon  
This box indicates system  
being selected.  
COMPONENT VIDEO SIGNAL FORMAT  
If projector can not reproduce proper video image, it is necessary to  
select a specific component video signal format among 480i, 575i,  
480p, 575p, 720p, 1035i and 1080i.  
Move the pointer to  
system and press  
SELECT button.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
PICTURE IMAGE ADJUSTMENT  
IMAGE LEVEL SELECT (DIRECT)  
Select image level among Standard, Cinema, Image 1, Image 2,  
Image 3 and Image 4 by pressing IMAGE button on Top control panel  
or on Remote Control Unit.  
IMAGE button  
Standard  
Cinema  
Image 1  
Image 2  
Image 3  
Image 4  
Standard  
Normal picture level preset on this projector.  
Cinema  
Picture level adjusted for picture with fine tone.  
IMAGE 1~4  
User preset picture adjustment in IMAGE ADJUST Menu (P34).  
IMAGE LEVEL SELECT (MENU)  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button to move the red frame pointer to  
IMAGE SELECT Menu icon.  
IMAGE SELECT MENU  
1
2
Press the POINT DOWN button to move the red frame pointer to  
level that you want to set and then press SELECT button.  
IMAGE SELECT  
Menu icon  
Standard  
Normal picture level preset on this projector.  
Cinema  
Move the red frame pointer to  
level and press SELECT button.  
Picture level adjusted for picture with fine tone.  
IMAGE 1~4  
Level being selected.  
User preset picture adjustment in IMAGE ADJUST Menu (P34).  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
IMAGE LEVEL ADJUSTMENT  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button(s) to move the red frame pointer  
to IMAGE ADJUST Menu icon.  
IMAGE ADJUST MENU  
1
2
Press the POINT DOWN button to move the red frame pointer to  
the item you want to adjust and then press SELECT button. The  
level of each item is displayed. Adjust each level by pressing the  
POINT LEFT/RIGHT button(s).  
IMAGE ADJUST  
Menu icon  
Move the red frame pointer to  
the item to be selected and  
then press SELECT button.  
Contrast  
Press the POINT LEFT button to decrease contrast, and the POINT  
RIGHT button to increase contrast. (From 0 to 63.)  
Brightness  
Press the POINT LEFT button to decrease brightness, and the  
POINT RIGHT button to increase brightness. (From 0 to 63.)  
Color  
Press the POINT LEFT button to lighten color, and the POINT  
RIGHT button to deeper color. (From 0 to 63.)  
Press the POINT LEFT/RIGHT but-  
tons to adjust value.  
Tint  
Press SELECT button at this icon to  
display other items.  
Press the POINT LEFT button or the POINT RIGHT button to obtain  
proper color. (From 0 to 63.)  
White balance (Red)  
Press SELECT button at this icon to  
display previous items.  
Press the POINT LEFT button to lighten red tone and the POINT  
RIGHT button to enhance red tone. (From 0 to 63.)  
White balance (Green)  
Press the POINT LEFT button to lighten green tone and the POINT  
RIGHT button to enhance green tone. (From 0 to 63.)  
Press the POINT LEFT/RIGHT but-  
tons to adjust value.  
White balance (Blue)  
Press the POINT LEFT button to lighten blue tone and the POINT  
RIGHT button to enhance blue tone. (From 0 to 63.)  
Sharpness  
Press the POINT LEFT button to soften image, and the POINT  
RIGHT button to sharpen image. (From 0 to 15.)  
Press SELECT button at this icon to  
store value.  
Gamma  
Press either the POINT LEFT button or the POINT RIGHT button to  
obtain better balance of contrast. (From 0 to 15.)  
NOTE :  
Tint can not be adjusted when video system is  
PAL, SECAM, PAL-M or PAL-N.  
Noise reduction  
Press the POINT LEFT/RIGHT button(s) to enable noise reduction  
mode. Dialog box display is changed to Onto reduce noises (rough  
Noise Reduction can not be operated when video  
signal types and systems as follow.  
parts) from the image. Press the POINT LEFT/RIGHT button(s) again Composite video signal (SECAM, NTSC4.43,  
PAL-M and PAL-N systems).  
to change the noise reduction mode to Off.  
S-video signal (SECAM, PAL-M and PAL-N  
Progressive scan  
systems).  
Component video signal.  
Press the POINT LEFT/RIGHT button(s) to enable progressive scan  
mode. Dialog box display is changed to Offand progressive scan  
mode is set to Off. Press the POINT LEFT/RIGHT button(s) again to  
change the progressive scan mode to On.  
Progressive can not be operated when 480p,  
575p, 720p, 1035ior 1080iis selected on AV  
SYSTEM MENU (P31).  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VIDEO INPUT  
Store  
3
To store adjustment data, move the red frame pointer to Store  
icon and press SELECT button. Image Level Menu will appear.  
Move the red frame pointer to Image Level 1 to 4 and then press  
SELECT button.  
Image Level Menu  
Other icons operate as follows.  
Move the red frame pointer  
to image icon to be set and  
then press SELECT button.  
Reset  
Reset all adjustment to previous settings.  
Quit  
Store icon  
Closes IMAGE MENU.  
PICTURE SCREEN ADJUSTMENT  
This projector has a picture screen adjustment function, which enables you to display the desirable image size.  
Press MENU button and ON-SCREEN MENU will appear. Press  
the POINT LEFT/RIGHT button(s) to move the red frame pointer  
to SCREEN Menu icon.  
SCREEN MENU  
1
2
Press the POINT DOWN button and move the red frame pointer  
to function that you want to select and then press SELECT  
button.  
SCREEN Menu icon  
Move the red frame to the function and  
press SELECT button.  
Normal  
Provides image at a normal video aspect ratio of 4 : 3.  
NOTE : SCREEN Menu can not be operated when  
720p,” “1035i,or 1080iis selected on AV  
SYSTEM Menu (P31).  
Wide  
Provides image at a wide screen ratio of 16 : 9.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
SETTING MENU  
Press MENU button and ON-SCREEN MENU will appear. Press  
SETTING MENU  
1
2
the POINT LEFT/RIGHT button(s) to move a red-frame pointer  
to SETTING icon.  
Press the POINT DOWN button to move a red-frame pointer to  
Set a red frame  
SETTING Menu icon  
item that you want to set and then press  
Setting dialog box appears.  
SELECT button.  
pointer to item and  
press SELECT  
button.  
Language  
Language used in ON-SCREEN MENU is selectable from among  
English, German, French, Italian, Spanish, Portuguese, Dutch,  
Swedish, Chinese, Korean and Japanese.  
Keystone  
When image is distorted, select Keystone. The ON-SCREEN MENU  
will disappear and the Keystone dialog box will appear. Correct  
keystone distortion by pressing the POINT UP/DOWN/LEFT/RIGHT  
button(s). Refer to KEYSTONE ADJUSTMENT on page 20.  
When pressing SELECT  
button at Language,  
Language Menu appears.  
Blue back  
When this function is On,this projector will produce a blue image  
instead of video noise on screen when any input source is unplugged  
or turned off.  
Display  
This function decides whether to display On-Screen Displays.  
On ··· shows all On-Screen Displays.  
Off ···· sets On-Screen Displays disappeared except;  
ON-SCREEN MENU  
Power off?message  
Logo  
When this function is On,the projector displays the CHRISTIElogo  
when starting up.  
Move a pointer to item and  
then press the POINT  
LEFT/RIGHT button(s).  
Ceiling  
When this function is On,picture is top / bottom and left / right  
reversed. This function is used to project image from a ceiling mounted  
projector.  
Ceiling function  
Rear  
When this function is On,picture is left / right reversed. This function is  
used to project image to a rear projection screen.  
Power management  
This function turns Projection Lamp off when this projector detects  
signal interruption and is not used for a certain period in order to  
reduce power consumption and maintain Lamp-life. (This projector is  
shipped with this function ON.)  
Rear function  
Power Management function operates to turn Projection Lamp off  
when input signal is interrupted and any button is not pressed over 5  
minutes. This function operates as follows;  
1. When any input signal is interrupted, No signaland counting  
down display appears (for 5 minutes).  
2. After counting down for 5 minutes, projector lamp and READY  
indicator are turned off.  
3. When READY indicator flashing, Projection Lamp can be turned  
on again (Power Management mode).  
In this Power Management mode, Projection Lamp is  
automatically turned on when input signal connected or projector  
is operated with any button on Top control panel or on Remote  
Control Unit again.  
Time left until Lamp off.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING  
On start  
When this function is On,projector is automatically turned on just  
by connecting AC Power cord to a wall outlet.  
Note ; Be sure to turn projector off properly (refer to section  
TURNING OFF PROJECTORon P19). If projector is turned  
off in wrong steps, On Start function does not operate  
properly.  
Lamp mode  
When selecting the  
brightness and set itself into low power consumption mode.  
(Eco) mode, the projector reduces the  
"
"
Press SELECT button at this icon to  
display other items.  
Remote control  
This projector has two different remote control codes; factory-set  
normal code (Code 1) and secondary code (Code 2). This switching  
function prevents remote control operation mixture (jam) when  
operating several projectors or video equipment together.  
When operating projector in Code 2,both projector and Remote  
Control Unit must be switched to Code 2.”  
On start  
To change code of Projector;  
Press SELECT button at this icon to  
display previous items.  
Set Remote control in SETTING MENU to Code 2.”  
To change code of Remote Control Unit;  
Press both MENU and IMAGE buttons on Remote Control Unit  
together for over 10 seconds.  
Move pointer to item and then press  
the POINT LEFT/RIGHT button(s).  
After changing code, make sure Remote Control operates properly.  
To return to normal code (Code 1), operate both projector and  
Remote Control in ways above again.  
NOTE : When batteries of Remote Control Unit are replaced or ALL-  
OFF switch is turned to ALL-OFF,remote transmit code  
automatically returns to normal code (Code 1).  
USB  
This Projector is equipped with USB port for interactive operation  
between a projector and a computer. Follow the steps below for USB  
setup  
Wireless Mouse mode  
Select "  
" when controlling a computer with Remote Control of  
this projector.  
Projector mode  
Select "  
" when controlling a projector with computer.  
NOTE: Before you control a projector by computer, install USB driver  
(optionally sold parts) and set up computer following instruc-  
tion in USB driver package. Contact your authorized dealer.  
ChristieNet  
This function can not be adjusted when the ChristieNet (optional  
part) is not attached to the projector.  
Refer to the owner's manual of the optional ChristieNet for operating  
instructions  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SETTING/APPENDIX  
Lamp counter reset  
Lamp  
counter reset  
This function is used to reset Lamp Replace Counter. When  
replacing Projection Lamp, reset Lamp Replace Counter by using  
this function. Refer to page 39 for operation.  
Quit  
Closes SETTING MENU.  
Move pointer to Lamp counter reset and then press  
SELECT button. Message Lamp replace counter  
reset?is displayed.  
OPERATING WIRELESS MOUSE  
The Wireless Remote Control Unit is not only able to operate this projector but also be used as a wireless mouse for most  
Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.  
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ON-  
SCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse  
function can not be used.  
INSTALLATION  
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)  
is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB  
port) of a Personal Computer is activated.  
Connect mouse port (or USB port) of your computer to Control  
Port (or USB connector) of this projector with Control Cable (or  
USB cable). (Refer to page 11, 12 for connection.)  
Note : When your computer has no mouse  
1
port, connect Serial Port of your  
computer to Control Port of a projector  
with Control Cable for Serial Port.  
Turn a projector on first, and then turn on your computer. When  
computer is switched on first, Wireless Mouse may not work  
properly.  
2
OPERATING WIRELESS MOUSE  
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK  
button on Wireless Remote Control Unit.  
POINT button  
POINT button (Move pointer)  
Used to move PC mouse pointer. Pointer is moved corresponding  
with direction you are pressing.  
SELECT (LEFT CLICK) button  
This button has same function as left button in a PC mouse.  
RIGHT CLICK button  
This button has same function as right button in a PC mouse. This  
button is not available for controlling this projector.  
SELECT button  
(left button of mouse)  
RIGHT CLICK button  
(right button of mouse)  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
MAINTENANCE  
WARNING TEMP. INDICATOR  
WARNING TEMP. Indicator flashes red when the internal temperature of the projector exceeds the normal temperature.  
This Indicator stops flashing when the temperature of the projector returns to normal.  
When WARNING TEMP. Indicator continues to flash, check items listed below.  
Ventilation Slots of the projector may be blocked. In such an event, reposition the projector so that Ventilation Slots are  
not obstructed.  
1
Air Filter may be clogged with dust particles. Clean Air Filter by following the section AIR FILTER CARE AND  
CLEANING below.  
2
If WARNING TEMP. Indicator remains on after performing the above checks, the Cooling Fans or the Internal Circuits  
may be malfunctioning. Contact service personnel from an authorized dealer or a service station.  
3
AIR FILTER CARE AND CLEANING  
The Air Filter prevents dust from accumulating on the surface of the Projection Lens and the Projection Mirror. Should Air  
Filter become clogged with dust particles, it will reduce Cooling Fanseffectiveness and may result in internal heat build up  
and adversely affect the life of the projector. Clean the Air Filter following the steps below:  
Turn off the projector and disconnect the AC Power Cord from  
the AC outlet.  
1
Turn the projector upside down and remove the Air Filters (2  
used) by pulling the latches upward.  
2
Clean the Air Filter with a brush or wash out the dust and  
particles.  
3
Replace the Air Filter properly. Make sure the Air Filter is fully  
inserted.  
4
CAUTION  
Do not operate the projector with the Air Filter removed.  
Dust may accumulate on LCD Panel and Projection Mirror  
degrading picture quality.  
Do not put small parts into Air Intake Vents. It may result  
AIR FILTER  
Pull up and remove.  
in malfunction of the projector.  
RECOMMENDATION  
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments  
may cause poor image quality.  
When using under dusty or smoky conditions, dust may accumulate on the lens, liquid crystal panels, or optical elements  
inside the projector. This condition may degrade the quality of the projected image.  
When the above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.  
CLEANING PROJECTION LENS  
Follow these steps to clean Projection Lens:  
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.  
Abrasive cleaners, solvents or other harsh chemicals might scratch a surface.  
1
Lightly wipe a cleaning cloth over Projection Lens.  
2
3
When the projector is not in use, replace the Lens Cover.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
LAMP REPLACEMENT  
When the life of the Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When  
a projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.  
CAUTION  
CAUTION  
For continued safety, replace with a lamp  
assembly of same type.  
Allow the projector to cool for at least 45  
minutes before you open Lamp Cover. The  
inside of the projector can become very hot.  
Do not drop a lamp assembly or touch a glass  
bulb! The glass can shatter and may cause  
injury.  
Follow these steps to replace lamp assembly.  
Turn off a projector and disconnect AC plug. Allow a projector to  
cool for at least 45 minutes.  
1
Loosen 2 screws with a screwdriver and open Lamp Cover.  
2
3
Loosen 2 screws with a screwdriver and pull out Lamp Assembly  
by grasping Handle.  
LAMP COVER  
Replace Lamp Assembly with a new one and tighten 2 screws  
back. Make sure that Lamp Assembly is set properly. Replace  
Lamp Cover and tighten 2 screws.  
4
LAMP  
ASSEMBLY  
HANDLE  
Connect AC Power Cord to a projector and turn it on.  
5
6
Reset Lamp Replace Counter (refer to section Lamp Replace  
Counterbelow).  
NOTE : Do not reset Lamp Replace Counter when Projection  
Lamp is not replaced.  
ORDER REPLACEMENT LAMP  
Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give the following  
information to the dealer.  
Model No. of your projector : 38-VIV205-01  
Replacement Lamp Type No. : 03-000667-01P  
(Service Parts No. 610 297 3891)  
LAMP REPLACE COUNTER  
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP  
REPLACE Indicator stops lighting.  
Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button(s)  
to move the red frame pointer to SETTING Menu icon (refer to page 37).  
1
Press the POINT DOWN button to move the red frame pointer to Lamp counter resetand then press  
The message "Lamp replace counter reset?" will display. Move pointer to [Yes] and then press SELECT button.  
SELECT button.  
2
3
Another confirmation dialog box will appear and select [Yes] to reset Lamp Replace Counter.  
Do not reset Lamp Replace Counter unless Projection Lamp is replaced.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TROUBLESHOOTING  
Before calling your dealer or service center for assistance, check matters below once again.  
1. Make sure you have connected the projector to your computer or video equipment as described in section "CONNECTING  
PROJECTOR" on pages 11 ~ 13.  
2. Check cable connection. Verify that all computer, video and power cord are properly connected.  
3. Verify that all power is switched on.  
4. If the projector still does not produce an image, re-start your computer.  
5. If an image still does not appear, unplug the projector from your computer and check your computer monitor's display.  
The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, be  
sure to turn the computer and monitor off before you power up the projector. Power equipment back on in order of :  
Projector and computer.)  
6. If problem still exists, check following chart.  
Problem:  
No power.  
Try these Solutions  
Plug the projector into your AC outlet.  
Make sure READY Indicator lights.  
Wait 90 seconds after the projector is turned OFF before turning the projector back on.  
NOTE : After pressing Power ON-OFF button to OFF, make sure the projector works as  
follows:  
1. LAMP indicator lights bright and READY indicator turns off.  
2. After 90 seconds, READY indicator lights green again and the projector may be  
turned on by pressing Power ON-OFF button.  
Check WARNING TEMP. indicator. If indicator flashes red, the projector can not be  
turned on.  
(See "TURNING ON/OFF PROJECTOR" section on page 19.)  
Check Projection Lamp. (Refer to page 39.)  
Adjust focus of the projector.  
Make sure the projection screen is at least 4.6(1.4m) from the projector.  
Check Projection Lens to see if it needs cleaning.  
Image is out of  
focus.  
NOTE : Moving the projector from a cool temperature location to a warm temperature  
location may result in moisture condensation on Projection Lens. In such an event,  
leave the projector OFF and wait until condensation disappears.  
Check Ceiling / Rear feature. (See SETTINGsection on page 35.)  
Picture is Left/Right  
reversed.  
Check Ceiling feature. (See SETTINGsection on page 35.)  
Picture is  
Top/Bottom  
reversed.  
Check Display feature.(See SETTINGsection on page 35.)  
Some displays are  
not seen during  
Operation.  
Check connection between your computer or video equipment and the projector.  
When turning the projector on, it takes about 30 seconds to display an image.  
Check system that you select is corresponding with your computer or video equipment.  
Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).  
No image.  
Check audio cable connection from audio input source.  
Adjust audio source.  
No sound.  
Press VOLUME (+) button.  
Press MUTE button.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
Problem:  
Remote Control Unit  
does not work.  
Try these Solutions  
Check batteries.  
Check ALL-OFF switch on Remote Control Unit is set to ON..  
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.  
Make sure you are not too far from the projector when using Remote Control Unit.  
Maximum operating range is 16.4(5m).  
Make sure the code of the Remote Control is set to conform to the projector.  
(See the SETTINGSsection on page 36.)  
Check the cable connection between the projector and your computer.  
Check mouse setting on your computer.  
Turn the projector on before turning on the computer.  
Wireless Mouse  
function does not  
work.  
SERVICE  
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.  
You can often correct operating problems yourself. If the projector fails to work properly, see the "TROU-  
BLESHOOTING" section on pages 40 and 41.  
If after following all operating instructions, you find that service is necessary, contact the Christie Service Station  
or store where you purchased the unit.  
Give the model number and explain the difficulty. We will advise you how to obtain service.  
This symbol on the nameplate means the product is Listed by Underwriters  
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety  
standards against risk of fire, casualty and electrical hazards.  
The CE Mark is a Directive conformity mark of the European Community (EC).  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
TECHNICAL SPECIFICATIONS  
Multi-media Projector  
Projector Type  
12.6" x 6.6" x 16.8" (319 mm x 168 mm x 429.5 mm)  
15.7 lbs (7.1 kg)  
(W x H x D)  
Dimensions  
Net Weight  
1.3" TFT Active Matrix type, 3 panels  
1024 x 768 dots  
LCD Panel System  
Panel Resolution  
Number of Pixels  
Color System  
2,359,296 (1024 x 768 x 3 panels)  
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N  
480i, 480p, 575i, 575p, 720p, 1035i and 1080i  
H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 100 Hz  
Up and Down  
High Definition TV Signal  
Scanning Frequency  
Motorized Lens Shift  
Horizontal Resolution  
Projection Lamp  
Input 1 Jacks  
800 TV lines (HDTV)  
275 watt type  
DVI Terminal (Digital), HDB 15-pin Terminal (Analog)  
and Stereo Mini Type Jack (Audio)  
BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo Mini  
Type Jack (Audio)  
Input 2 Jacks  
Input 3 Jacks  
Other Jacks  
RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)  
and DIN 4-pin (S-Video)  
DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack  
and ChristieNet Connector  
INT. SP. Stereo (R and L), 2 watt RMS (T.H.D. 10%)  
Built-in Speakers  
0˚ to 10.5˚  
Feet Adjustment  
Voltage and  
Power Consumption  
Operating Temperature  
AC 100 ~ 120 V (4.8 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)  
AC 200 ~ 240 V (2.4 A Max. Ampere), 50 / 60 Hz (Continental Europe)  
41 F ~ 95 F (5 ˚C ~ 35 ˚C)  
14 F ~ 140 F (-10 ˚C ~ 60 ˚C)  
Storage Temperature  
Power Source  
Operating Range  
Dimensions  
Net Weight  
Laser Pointer  
:
:
:
:
:
AA, UM3 or R06 Type x 2  
16.4(5m) / ±30˚  
2.2x 1.3x 7.6(55mm x 34mm x 192mm)  
0.36 lbs (165 g) (including batteries)  
(Max. Output : 1mW / Wave length : 650±20nm)  
Class II Laser  
Remote Control Transmitter  
Users Manual  
Accessories  
AC Power Cord  
Wireless/Wired Remote Control Transmitter and Batteries  
Remote Control Cable  
VGA Cable  
MAC/VGA Adapter  
3 Types Control Cable (For PS/2, Serial and ADB port)  
Protective Dust Cover  
Specifications are subject to change without notice.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
APPENDIX  
CONFIGURATIONS OF TERMINALS  
COMPUTER INPUT-1 TERMINAL (ANALOG)  
Terminal : HDB15-PIN  
Connect the display output terminal of the computer to this terminal with the VGA Cable (supplied). When connecting the  
Macintosh computer, the MAC Adapter (supplied) is required.  
1
2
3
4
5
6
7
8
Red Input  
Green Input  
Blue Input  
Sense 2  
9
+5V Power  
Pin Configuration  
10 Ground (Vert.sync.)  
11 Sense 0  
2
1
5
4
3
12 DDC Data  
10  
9
8
7
6
15  
14  
13  
12  
11  
Ground (Horiz.sync.) 13 Horiz. sync.  
Ground (Red)  
Ground (Green)  
Ground (Blue)  
14 Vert. sync.  
15 DDC Clock  
COMPUTER INPUT-1 TERMINAL (DIGITAL)  
Terminal : DVI 24-pin  
Connect the display output terminal of the computer to this terminal with a DVI cable (for Single Link T.M.D.S. / not supplied).  
1
2
3
4
5
6
7
8
T.M.D.S. Data2–  
9
T.M.D.S. Data1–  
17 T.M.D.S. Data0–  
18 T.M.D.S. Data0+  
Pin Configuration  
T.M.D.S. Data2+  
10 T.M.D.S. Data1+  
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield  
1
9
2
3
4
5
6
7
8
No Connect  
No Connect  
DDC Clock  
DDC Data  
12 No Connect  
13 No Connect  
14 +5V Power  
20 No Connect  
10 11 12 13 14 15 16  
17 18 19 20 21 22 23 24  
21 No Connect  
22 T.M.D.S. Clock Shield  
23 T.M.D.S. Clock+  
24 T.M.D.S. Clock–  
15 Ground (for +5V)  
16 Hot Plug Detect  
No Connect  
CONTROL PORT CONNECTOR  
Terminal : Mini DIN 8-PIN  
Connect control port (PS/2, Serial or ADB port) on your computer to this connector with the Control Cable (supplied).  
PS/2  
-----  
Serial  
R X D  
-----  
ADB  
-----  
Pin Configuration  
1
2
3
4
5
6
7
8
CLK  
DATA  
GND  
-----  
ADB  
-----  
-----  
8
7
6
GND  
GND  
-----  
5
4
3
RTS / CTS  
T X D  
GND  
2
1
-----  
-----  
GND  
-----  
-----  
GND  
GND  
USB CONNECTOR (Series B)  
Connect USB port terminal on your computer or peripheral equipment to this connector with USB Cable (not supplied).  
Pin Configuration  
1
2
3
4
Vcc  
- Data  
+ Data  
Ground  
2
3
1
4
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed in Japan  
Part No. 10-A 610 302 1256 (1AA6P1P3605-- MB8KM)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Laptop Docking Station F5U216 User Manual
Black Box Computer Hardware ACS250A R2 User Manual
Black Decker Iron F63E User Manual
Blue Rhino Gas Grill GBC820WC C User Manual
BMW GPS Receiver Navigation Portable Pro User Manual
Briggs Stratton Pressure Washer 020274 0 User Manual
Campbell Hausfeld Nail Gun CHN20103 User Manual
Canon All in One Printer 4206B002 User Manual
Casio Printer KL 750E User Manual
Century Car Seat STE User Manual