I N S T A L L A T I O N I N S T R U C T I O N S
Large Flat Panel Dual Arm Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PNR Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
DIMENSIONS
NOTE: PSBU INTERFAC E BRAC KET
NOT SHOWN. THE PSBU INTERFAC E
BRAC KET WILL ADD 1” IN DEPTH
AND MAY AFFEC T THE LOC ATION
OF THE DISPLAY ON THE MOUNT.
Mounting Pa ttern
483
19.00
178
7.00
38
1.50
46
1.81
25
1.00
25
1.00
500
19.69
538
21.19
10
.40
4
.18
406
16.00
DIMENSIONS: [MILLIMETERS]
INCHES
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
DIMENSIONS -- cont’d
Unit Depth
Tilt Adjustment *
Tilted Up
Tilted Down
Extended
Retra c ted
5°
17°
83
3.25
635
25.00
687
27.06
*The ra nge of a djustment will v a ry with diffe rent size s creens
2°
66
2.61
Highest Height Setting
39
1.53
Lowest Height Setting
Roll Adjustment
90.00°
18.21
161.09°
MAX
22.65
MAX
76.17°
MAX
76.17°
MAX
10.84
DIMENSIONS: [MILLIMETERS]
INCHES
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Zeskantsleutel
Clé à fourche
Clé à tête hexagonale
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
7/32" (5.5mm)
9/16"
PARTS
B (2)
[Cover]
A (1)
[PNR assembly]
C (2)
[End cap]
D (2)
[End cap]
F (1)
[Adjustment insert]
E (1)
G (4)
.850x.385x.135
[Adjustment wrench]
J (12)
5-1/2" Cable tie
H (4)
5/16 x 2-1/2"
K (1)
[PSBU bracket]
(Only included with PNRU)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
5. Drill four 7/32" pilot holes where the mounting holes were
marked. (See Figure 2)
Installing Mount to Wall
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s
responsibility to make sure the structure to which the mount
is being installed is capable of supporting five times the
combined weight of the mount and all attachments.
1
NOTE: The following instructions assume a suitable mounting
structure and surface exists prior to installation.
CAUTION: To avoid personal injury, use an assistant when
lifting, lowering or holding PNR during installation.
3
1. Determine mounting location taking into consideration
display size and PNR’s range of movement.
2. Using a stud sensor locate two wood studs 16” on center.
(See Figure 1)
3
16"
Wood Studs
4
x 4
5
Figure 2
Pilot
Holes
(Wall)
Figure 1
3. Place and level mount against wall, aligning mounting holes
in upper and lower wall channels with studs. (See Figure 2)
4. Mark four mounting holes making sure mounting holes are
located as close as possible to center of studs.
(See Figure 2)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
6. Install two 5/16” x 2-1/2” lag bolts (H) and two
.850x.385x.135” washers (G), through mounting holes in
upper wall channel and into pilot holes. DO NOT tighten at
this time. (See Figure 3)
7. Place mount against wall aligning mounting holes in upper
wall channel with lag bolts, and hang mount on lag bolts
making sure washers are located in front of mount.
8. Adjust mount lateral position left until lag bolts are seated in
mounting slots in upper wall channel. (See Figure 3)
9. Install two 5/16" x 2-1/2" lag bolts (H) and two
.850x.385x.135” washers (G), through mounting holes in
lower wall channel and into pilot holes. (See Figure 3)
Lower
1
10. Tighten all hardware. DO NOT over tighten!
Raise
Adjustment nut
8
(G) x 2
Figure 4
6
9
(H) x 4
Installing Covers and End Caps
NOTE: The covers and end caps have pressure fitting ends
that lock into place with each other.
1. Install cover (B) over the top bracket. (See Figure 5)
2. Install end caps (C and D) into the cover and top bracket.
(See Figure 5)
3. Repeat Steps 1 and 2 for the lower mounting bracket. (See
Figure 5)
2
(G) x 2
(D)
Figure 3
Adjusting PNR Height
(B)
NOTE: Height adjustment range up to 1.08 inches.
1
1. Check PNR for the desired height. If needed, use the
adjustment wrench (E) to adjust the PNR height. (See
Figure 4)
2
•
Turn adjustment nut clockwise to lower the unit height,
or
•
Turn adjustment nut counterclockwise to raise the unit
height.
(C)
Figure 5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
Mounting the Display
To use as a
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.
more permanent
lock, remove pin
and nuts and move
to lower holes.
3
1. Install PSBU interface bracket (K - included with PNRU
only) to display using hardware and installation instructions
included with PSBU bracket.
4
2. Move faceplate to extended position by grasping faceplate
and pulling outward away from wall.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
A padlock or bolt may be
placed through latch holes.
3. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See Figure 6) and (See Figure 7)
Figure 7
4. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and ClickConnect
mechanismengages.(SeeFigure6) and (SeeFigure7)
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 7)
3
4
Figure 6
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
Cable Management
Tension Adjustments
Vertical Tilt Tension Adjustment
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Make sure cables do not run through pinch
points.
1. With display mounted, check for desired vertical tilt tension.
2. Adjust the Centris Select knob until desired vertical tilt
tension is obtained. (See Figure 9)
1. Thread cable ties (J) under cable clamps in mount arms.
(See Figure 1)
3. To lock the mount at the desired vertical tilt, tighten the
vertical tilt lock screw. (See Figure 10)
Centris Select
adjustment knob
Top view
1
Cable tie
Figure 9
Cable clamps
Vertical tilt
lock screw
Cable tie
Figure 10
Figure 8
2. Route power/audio/video cables through the cable channel
in top arm (See Figure 8), allowing sufficient slack in cables
for left / right movement of display and swing arm, as well
as swing arm extension and retraction.
3. Secure cables to top arm using two cable ties (J).
4. Repeat Steps 1 through 3, as necessary, for remaining top
arm and lower arms.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! DO NOT route cables through holes in
faceplate.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
Swivel Tension Adjustment
Swing Arm Adjustments
The dual swing arms are shipped installed in the center of the
top and bottom mounting brackets, which is the standard
mounting configuration.
CAUTION: DO NOT OVER TIGHTEN SWIVEL
ADJUSTMENT NUT. Over tightening swivel adjustment nut
will cause excessive wear and may distort adjustment
components.
The top and bottom mounting brackets have slotted holes,
allowing for lateral adjustment of the dual swing arms.
After installing top and bottom mounting brackets between two
wood studs 16” on center, the swing arms can be adjusted or
moved off center, depending on the location of the mount, size
of display, and lateral movement needed to rotate the display.
1. Using a 9/16” wrench (not provided), slightly tighten or
loosen swivel tension adjustment nut. (See Figure 11)
2. Repeat until desired tilt tension is obtained.
Roll Tension Adjustment
The swing arms can be adjusted, as follows:
1. If necessary, loosen or tighten roll tension adjustment nut.
(See Figure 11)
•
Adjusting the Swing Arms Off-Center
With no disassembly required, you can adjust the
swing arms up to 1-inch to the left of center or up to
1-inch to the right of center.
2. Repeat until desired rotational tilt tension is obtained.
•
Reconfiguring the Swing Arms Left of Center
With some disassembly and reassembly required, you
can move the swing arms to the left of center by
reconfiguring the mount. Use the first and third slotted
holes in the top and bottom mounting brackets.
Swivel tension
adjustment nut
•
Reconfiguring the Swing Arms Right of Center
With some disassembly and reassembly, you can
move the swing arms to the right of center by
reconfiguring the mount. Use the third and fifth slotted
holes in the top and bottom mounting brackets.
Adjusting the Swing Arms Off Center
1. Remove the display from the mount.
2. Loosen four bolts (two on the top and two on the bottom)
securing the swing arm assembly to top and bottom
mounting brackets (See Figure 12).
3. Move the swing arm assembly left or right within slots to
desired location.
4. Tighten the bolts.
5. Install the display on the mount.
Top bolts
Roll tension
adjustment nut
Figure 11
Figure 12
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
3. Move the swing arm assembly left or right within slots to
desired location.
Reconfiguring the Swing Arms to Left or Right of
Center
•
Left of Center (See Figure 13).
Right of Center (See Figure 14).
1. Remove the display from the mount.
•
4. Install four bolts (two on the top and two on the bottom) to
secure the swing arm assembly to the top and bottom
mounting brackets.
WARNING: The next step will release the arm assembly
from the mount. The arms and plate may fall if you are not
careful.
5. Tighten the bolts.
2. Remove four bolts (two on the top and two on the bottom)
securing the swing arm assembly to the top and bottom
mounting brackets. (See Figure 13)
6. Install the display on the mount.
Top bolts
Top bolts
Figure 14
Figure 13
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
Swing Arm Tension Adjustment
Swing arm tension is pre-set at the factory and is adjusted to
accommodate displays with weights near the top of the mount’s
capacity.
Increase tension
If smaller displays are used it may be difficult to reposition the
display after mounting.
NOTE: The display must be mounted prior to adjusting swing
arm tension.
To adjust swing arm tension to compensate for smaller display:
1. Place adjustment insert (F) into tension adjustment screw
located at swing arm pivot point. (See Figure 15)
NOTE: The display may need to be repositioned in order to
gain access to the tension adjustment screw(s).
2. Use the adjustment wrench (E) provided with the mount,
turn adjustment insert clockwise to increase swing arm
tension (See Figure 16) or counterclockwise to reduce
swing arm tension. (See Figure 17)
NOTE: Small adjustments of 1/8 turn or less are typically all
that is required to achieve desired tension.
Figure 16
3. Check swing arm tension. If desired tension is present,
tension adjustment is complete. If additional tension
adjustment is required, repeat steps 1 and 2 until desired
tension is achieved.
NOTE: If changing from a smaller display to a larger display it
Reduce tension
may be necessary to increase swing arm tension.
(E)
Tension adjustment
screw
Figure 17
(F)
Figure 15
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
3. Carefully lift display from mount
Removing Display from Mount
1. Remove bolt or padlock from faceplate (if used).
4. Lift up on pin and place flag back against faceplate to return
it to "Closed" position. (See Figure 19)
NOTE: The pin may have been used as a more permanent
locking device. If so, remove nut and pin and move
from the lower holes to the upper holes.
2. Pull back on flag on upper mounting hole and press pin
down into "Open" position. (See Figure 18)
4
WARNING: DISPLAY MAY WEIGH IN EXCESS OF 40
LBS! Always use two people and proper lifting techniques
when installing or positioning display on mount.
Remove bolt
or padlock
if used.
1
Pin in
"Open"
position -
move to
"Closed"
position
2
after display
is removed.
Pin in
"Closed"
position -
move to
"Open"
position to
remove
display.
Figure 19
Figure 18
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PNR Series
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PNR Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344
800.582.6480 / 952.225.6000
877.894.6918 / 952.894.6918
Franklinstraat 14, 6003 DK Weert, Netherlands
+31 (0) 495 580 852
+31 (0) 495 580 845
Chief, a products division of
Milestone AV Technologies
Asia Pacific
A
Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
852 2145 4099
852 2145 4477
8800-002618 Rev00
¤2014 Milestone AV Technologies
07/14
P
F
Download from Www.Somanuals.com. All Manuals Search And Download.
|