I N S T A L L A T I O N I N S T R U C T I O N S
MSP-DARKWE110
MSP-DARKCD110
MSP-DARKPZ110
MSP-DARKCE110
Extreme Pitch Wall / Desk Mount / Pole Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MSP-DARKWE/CE/CD/PZ-110
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MSP-DARKWE/CE/CD/PZ-110
DIMENSIONS
MSP-DARKCD
.25
4.10
MIN EXTENSION
VESA 100 x 100
VESA 75 x 75
VESA 100 x 100
VESA 75 x 75
9.24
11.97
11.18
6.77
4.81
MSP-DARKPZ
6.50
2.96
MIN EXTENSION
19.48
MAX EXTENSION
10.02
2.34
VESA 100 x 100
VESA 75 x 75
VESA 100 x 100
VESA 75 x 75
8.80
2.15
DIMENSIONS: [MILLIMETERS]
INCHES
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MSP-DARKWE/CE/CD/PZ-110
Installation Instructions
DIMENSIONS Continued
MSP-DARKWE
MIN EXTENSION
20.16
MAX EXTENSION
10.02
2.34
VESA 100 x 100
VESA 75 x 75
VESA 100 x 100
VESA 75 x 75
3.05
FULLY LOWERED
MSP-DARKCE
6.25
.25
6.50
20.62
MAX EXTENSION
VESA 100 x 100
VESA 75 x 75
VESA 100 x 100
VESA 75 x 75
DIMENSIONS: [MILLIMETERS]
INCHES
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MSP-DARKWE/CE/CD/PZ-110
LEGEND
Tighten Fastener
Drill Hole
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Percez un trou
Loosen Fastener
Hex-Head Wrench
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Zeskantsleutel
Clé à tête hexagonale
Phillips Screwdriver
By Hand
Destornillador Phillips
A mano
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Von Hand
Com a mão
A mano
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Met de hand
À la main
Pencil Mark
Adjust
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MSP-DARKWE/CE/CD/PZ-110
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
1/8” (3.2mm)
#2
3/32” (included)
5/32” (included)
3/16” (included)
7/16”
PARTS
A (1)
B (1)
[MSP-DARKWE110]
[MSP-DARKCE110]
B (1)
V (1)
[MSP-DARKCD110]
[MSP-DARKPZ110]
J
H
G (3)
#10
(4.8mm)
E (2)
1/4”
(4.8mm)
D (2)
1/4” x 2-1/2”
(4.8 x 64mm)
**
*
*
F (3)
#10 x 1-1/2”
(4.8 x 38mm)
#8 x 3/8”
(4.0 x 9.5mm)
**
(DARKWE110 x 1)
(DARKCE110 x 1)
(DARKCD110 x 2)
(DARKPZ110 x 1)
C (1)
[wall plate]
*
(DARKWE110 x 2)
(DARKCE110 x 4)
(DARKCD110 x 4)
(DARKPZ110 x 2)
R (1)
3/16”
(4.8mm)
S (1)
3/32”
(2.4mm)
Q (1)
5/32”
(4.0mm)
P (4)
N (4)
3/8”
(9.5mm)
L (4)
M4 x 20
M (4)
M4 x 30
K (4)
M4 x 12
3/4”
(19mm)
*-MSP-DARKWE110 only
**-MSP-DARKCD110/CE110 only
T (3)
1/4-20 x 1-1/4”
(MSP-DARKPZ110)
U (1)
(MSP-DARKPZ110)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MSP-DARKWE/CE/CD/PZ-110
MOUNT INSTALLATION
To Wall (MSP-DARKWE110)
1. Determine location for mount keeping in mind extension
and height adjustment requirements.
2. Using wall plate (C) as a template, mark location for two
pilot holes through top and bottom holes of wall plate. (See
Figure 1)
A
C
2
(D) x 2
4
5
3
(E) x 2
(C)
5
Figure 1
Figure 2
3. Drill two 1/8” diameter pilot holes through marked locations
into wall structure. (See Figure 1)
7. Using hex key (R), tighten set screw (See Figure 3). Ensure
set screw engages back side of bracket (C) to properly
secure mount.
4. Using 7/16” wrench, loosely install two 1/4” x 2 1/2” hex
head lag screws (D) through two 1/4” washers (E), wall plate
(C), and drywall into wood stud. (See Figure 1)
NOTE: Proper engagement of set screw prevents lower end of
mount (A) from being tilted away from wall.
5. Ensure wall plate (C) is vertical, then tighten screws (D).
IMPORTANT ! : Over-tightening screws (D) may cause
bracket (C) to compress into soft wall surface, resulting in
damage to wall, difficult mount installation, and/or
improper engaging of set screw in Step 6.
IMPORTANT ! : If you will be installing a display with
RECESSED mounting holes, then proceed to “DISPLAY
INSTALLATION” before continuing with this mount
installation procedure.
A
C
6. Insert top of mount (A) over lip on top of bracket (C) (See
Figure 2). Swing mount (A) down flush against wall.
6
Figure 3
8. Proceed to “CABLE MANAGEMENT” if your display was
previously installed, or to “DISPLAY INSTALLATION” if your
display is not installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MSP-DARKWE/CE/CD/PZ-110
Installation Instructions
To Desk (MSP-DARKCE110, MSP-DARKCD110)
1. Determine approximate location for mount keeping in mind
display size, arm extension, and pitch/roll requirements.
(T) x 3
3
2. Using mount (B) as a template, mark location of three pilot
holes (See Figure 4).
3. Drill three 1/8” diameter pilot holes in mounting structure at
marked locations (See Figure 4). Ensure pilot holes are
straight.
(V)
(U)
Pole
Figure 5
NOTE: Equally tighten screws (T) against clamp (U) and mount
(F) x 3
4
(V). (See Figure 6)
(G) x 3
x3
x3
2
3
(T) x 3
(U)
B
Keep equal
distance between
mount and
clamp when
tightening
(V)
1/8” (3.2mm)
Figure 4
IMPORTANT ! : IF you will be installing a display with
RECESSED mounting holes, then proceed to “DISPLAY
INSTALLATION” before continuing with this mount installation
procedure.
Figure 6
4. Position mount at desired height and orientation. Tighten
screws (T) securely.
4. Install three #10 x 1 1/2” Phillips head screws (F) through
three #10 washers (G) and mount (B) into pilot holes (See
Figure 4). Tighten screws.
5. Proceed to “CABLE MANAGEMENT” if your display was
previously installed, or to “DISPLAY INSTALLATION” if your
display is not installed.
5. Proceed to “CABLE MANAGEMENT” if your display was
previously installed, or to “DISPLAY INSTALLATION” if your
display is not installed.
DISPLAY INSTALLATION
NOTE: In Figures 7 and 8 the swing arm has been removed for
To Pole (MSP-DARKPZ110)
clarity.
IMPORTANT ! : The following installation instructions
assume that a 1-1/2” NPT pipe has been properly
installed and is in place.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the MSP-DARKWE110/-
DARKCE110 does not exceed 20 lbs (9 kg), MSP-
DARKCD110/MSP-DARKPZ110 - 25 lbs (11.3 kg).
1. Determine approximate location for mount keeping in mind
display size, extension, height adjustment (if applicable),
and pitch/roll requirements.
IMPORTANT ! : IF you will be installing a display with
RECESSED mounting holes, then proceed to “DISPLAY
INSTALLATION” before continuing with this mount installation
procedure.
1. Carefully place display face down on protective surface.
2. Place mount (V) against pole, with clamp (U) on opposite
side of pole (See Figure 5).
3. Using 5/32” hex key (Q), loosely assemble with three 1/4-20
x 1-1/4” button head cap screws (T). (See Figure 5)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MSP-DARKWE/CE/CD/PZ-110
2. Select spacers:
•
If mounting holes are flush with back of display,
then no spacers are required; proceed to Step 3
below.
(K, L or M) x 4
5
•
If mounting holes are recessed into back surface
of display, then place spacer (N or P, as
applicable) over each mounting hole on back of
display (See Figure 8). Select shortest spacer
which will provide adequate fill. All spacers must
be same length.
Faceplate
NOTE: 100 x 100 mounting hole pattern shown; 75 x 75mm
pattern similar.
3. Select screw length:
•
•
•
If no spacers are required, then use screws (K).
If using spacers (N), then use screws (L).
If using spacers (P), then use screws (M).
4. Orient mount (A, B or V) so that mounting holes in faceplate
are aligned with holes in display or holes in spacers (M, N),
as applicable.
CAUTION: Using screws of improper size may damage
your display! Proper screws will easily and completely thread
into display mounting holes.
5. Install screws (K, L, or M; as applicable) through mounting
holes on faceplate and spacers (N or P, if applicable) into
display (See Figure 7) (See Figure 8).
Figure 7
6. Tighten all four screws. Do not over-tighten!
x 4
5
Faceplate
(N, P) x 4
2
Figure 8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MSP-DARKWE/CE/CD/PZ-110
Installation Instructions
CABLE MANAGEMENT
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cover (H) or screws (J).
NOTE: Steps 1 through 6 below apply to models
DARKWE110, DARKCE110 and DARKPZ110.
Proceed to Step 5 if installing DARKCD110.
1. Attach all cables to display.
5. Carefully insert cables in cavity located in lower portion of
mount arm (See Figure 11).
2. Open the cable management bracket by sliding it towards
the edge of the arm (See Figure 9).
6. Using Phillips screwdriver, install two covers (H) with four
screws (J).
NOTE: If necessary, cable management bracket attach screws
may be loosened using hex key.
Cable Path
(typical)
Attach
Screws
4
2
5
(H) x2
CLOSED Position
OPEN Position
(J) x4
6
View from Bottom
Figure 9
Figure 11
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched
when bracket is closed.
3. Carefully insert cables into bracket (See Figure 10).
3
Cable Management
Bracket (in open position)
Cable Path (typical)
NOTE: Display not shown for clarity.
Figure 10
4. Close cable management bracket by sliding it back towards
the center line of the arm (See Figure 9).
NOTE: If necessary, cable management bracket attach screws
may be tightened using hex key.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
MSP-DARKWE/CE/CD/PZ-110
Pitch Adjustment
ADJUSTMENTS
1. Pull entire handle out away from mount to allow handle
position to be adjusted to be prior to pitch adjustment. (See
Figure 13)
Pivot/Height Tension
NOTE: In order to maximize leverage, position handle in lower
WARNING: Excessive loosening or tightening of
adjustment mechanism can result in serious personal injury
or damage to equipment!
position.
2. Adjust handle to desired position. (See Figure 13)
1. To adjust extension/swivel, slightly loosen or tighten
adjustment screws using hex key (R) (See Figure 12).
Adjust screws ONLY as required to achieve desired tension.
3. Push entire handle back towards mount prior to pitch
adjustment. (See Figure 13)
2. To adjust height tension, slightly loosen or tighten
adjustment screw as necessary using hex key (Q) (See
Figure 12).
•
If display settles on its own, then rotate
adjustment screw counterclockwise (towards the
“+” symbol).
•
If display rises on its own, then rotate adjustment
screw clockwise (towards the “-” symbol).
1
NOTE: It may be necessary to raise or lower the height
adjustable arm to expose the adjustment screw.
3
2
(R)
1
Figure 13
IMPORTANT ! : Make sure the weight of the display is
adequately supported while adjusting the pitch in Steps
4-6!
4. Lift handle up until pitch can be adjusted easily. (See Figure
14)
5. Adjust pitch to desired position. (See Figure 14)
DARKWE110
(Other models similar)
6. Push handle down until faceplate is locked at desired pitch
position. (See Figure 14)
5
4
(Q)
2
Figure 12
6
Figure 14
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MSP-DARKWE/CE/CD/PZ-110
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344
800.582.6480 / 952.225.6000
877.894.6918 / 952.894.6918
Franklinstraat 14, 6003 DK Weert, Netherlands
+31 (0) 495 580 852
Chief Manufacturing, a products division
of Milestone AV Technologies
+31 (0) 495 580 845
8800-002389 Rev00
¤2013 Milestone AV Technologies, a
Duchossois Group Company
06/13
Asia Pacific
A
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
852 2145 4099
852 2145 4477
P
F
Download from Www.Somanuals.com. All Manuals Search And Download.
|