I N S T A L L A T I O N I N S T R U C T I O N S
Locking Projector Mount
RPAA1, B1, C1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
RPAA1, B1, C1
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RPAA1, B1, C1
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
PARTS
Q (1)
S (1)
5/32"
T (8)
U (4)
V (4)
R (4)
O (1)
3/32"
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
RPAA1, B1, C1
ASSEMBLY AND INSTALLATION
6. Thread RPAA1 sleeve up onto pipe by turning
Installing Threaded Pipe and RPAA1 Outer
Sleeve
counterclockwise until hand tight. (See Figure 3)
WARNING: IMPROPER INSTALLATION CAN RESULT IN
SERIOUS PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Structural members MUST be capable of
supporting five times the combined weight of all equipment
being mounted.
1
1. Install ceiling plate and extension accessories following
installation instruction provided by manufacturer.
2. Remove drawer from RPAA1 outer sleeve. (See Figure 1)
6
2
5
Figure 3
Rough Alignment of RPAA1
1. Turn RPAA1 sleeve clockwise or counterclockwise until the
front of the RPAA1 is facing target. (See Figure 4)
Figure 1
3. Remove and keep security screw from bottom of RPAA1
sleeve. (See Figure 2)
Set
Screw
1
2
Security
Tab
Figure 4
2. Tighten set screw. (See Figure 4)
Security
Screw
3
3. Return security tab to left side (See Figure 5).
4. Replace and tighten security screw (See Figure 5).
4
Figure 2
4. Move security tab to right. (See Figure 2)
5. Align RPAA1 outer sleeve with end of NTP pipe. (See
Figure 3)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RPAA1, B1, C1
Installation Instructions
2
(T) x 4
(U) x 4
4
3
Figure 7
Attaching Projector to Security Mount Drawer
1. Align projector and security mount drawer so that the
projector is oriented correctly.
Figure 5
Attaching Projector Security Legs
2. Remove the paper backing from the adhesive washers (V)
and attach projector to drawer using adhesive washers (V)
and thumbnuts (P) over the security legs (R). (See Figure 8)
1. Attach the projector security legs (R) to the projector, using
the correct size screws and washers for your specific
projector. (See Figure 6)
(P) x 4
x 4
(V) x 4
(M) or (N) x 4
(R) x 4
Security
Legs (R)
Projector
Projector
Figure 8
3. Slide the security mount drawer into the RPAA1 outer
sleeve. (See Figure 9)
Figure 6
2. Add washers (U) to the projector security legs (R). Add
spacers (T) as necessary to the projector security legs (R).
(See Figure 7)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
RPAA1, B1, C1
5. Adjust projector to desired roll.
6. Tighten adjustment screws.
Security
Mount
Drawer
RPAA1
Outer
Sleeve
Yaw
The yaw was adjusted when the RPAA1 was attached to the
pipe. If the yaw needs to be adjusted further, follow Steps 1-4
under Rough Alignment of RPAA1.
Locking the RPAA1
After all installation and adjustment steps have been
completed, lock the RPAA1. (See Figure 11)
Projector
Figure 9
Aligning Projector
The RPAA1 can be adjusted for vertical elevation (pitch),
horizontal tilt (roll), and rotation (yaw).
RPAA1
Lock
Figure 11
Roll
Adjustment
Screws
Pitch
Adjustment
Screw
Figure 10
Pitch
Adjust pitch using the adjustment screw on the end of the
adjustment plate. (See Figure 10)
1. Loosen the adjustment screw.
2. Adjust projector angle to desired pitch.
3. Tighten adjustment screw.
Roll
Adjust roll using the two adjustment screws on the back of the
adjustment plate. (See Figure 10)
4. Loosen the two adjustment screws.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RPAA1, B1, C1
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8802-000253
¤2007 Chief Manufacturing
04/07
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|