Chief Manufacturing Projector Accessories MSP DUK9000 User Manual

I N S T R U C T I O N  
M A N U A L  
PART #MSP-DUK9000  
Universal  
Ceiling Projector Mount Kit  
The Universal Ceiling Projector Mount provides a unique, sim-  
plified method of ceiling mounting your inverted projector. This  
low profile design offers three easy mounting methods (adjust-  
able column, flush or threaded rod); roll, pitch and yaw adjust-  
ment; a cable management system; and a universal bracket that  
allows quick projector disconnect without loss of registration.  
The Universal Ceiling Projector Mount is constructed of heavy  
gauge steel and designed to ensure proper projector ventilation.  
Fast and precise image registration is achieved through the easy  
roll, pitch and yaw adjustments built into the Universal Ceiling  
Projector Mount.  
BEFORE YOU BEGIN  
CAUTION: To prevent damage to the Universal Ceiling Mount, which could affect or void the Factory warranty, thor-  
oughly study all instructions and illustrations before you begin to install the Universal Ceiling Mount. Pay particular  
attention to the “Important Precautions” on Page 1.  
8832-000048 Rev. A00  
©2004 Chief Manufacturing  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918 EUROPE 49 7031/76 91 41  
8401 EAGLE CREEK PARKWAY  
SAVAGE, MINNESOTA 55378 USA  
Printed in USA 09/04  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
PARTS & DIMENSIONS  
Table 1:  
ITEM  
Nomenclature  
Ceiling Column  
Qty  
ITEM  
Nomenclature  
Qty  
10  
1
1
1
1
1
4
4
4
1
1
1
1
1
1
1
160  
170  
180  
190  
200  
210  
220  
230  
240  
250  
260  
270  
280  
290  
Cable Tie  
4
1
20  
1/4”-20 Locking Nut  
Cable Wrap  
30  
1/4”-20 x 1 1/2” Security Bolt  
1” NPT Column  
M3 X 12mm Button Head Security Screw  
M4 X 12mm Button Head Security Screw  
M5 X 12mm Button Head Security Screw  
M6 X 12mm Button Head Security Screw  
1/4”-20 x .625” Button Head Security Screw  
1/4”-20 NyLock Locknut  
4
4
4
4
4
2
4
4
4
4
4
4
40  
50  
Universal Projector Mount  
Thumb Nut  
60  
70  
M3 X 12mm Phillips Pan Head Screw  
M3 Flat Washer (Standard)  
Universal Mini SLB Assembly  
3/16” Security Hex Key  
80  
90  
M4 X 12mm Phillips Pan Head Screw  
M5 X 12mm Phillips Pan Head Screw  
M6 X 12mm Phillips Pan Head Screw  
M4 Flat Washer (Standard)  
100  
110  
120  
130  
140  
150  
5/32” Security Hex Key  
3/32” Security Hex Key  
5/32” Security Hex Key (Standard)  
5/16-18 X .50” Security Set Screw  
#10-24 X .25” Security Flat Head Screw  
M5 Flat Washer (Standard)  
M6 Flat Washer (Standard)  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
INSPECT THE UNIT BEFORE INSTALLING  
1. Carefully inspect the Universal Ceiling Projector Mount for  
shipping damage. If any damage is apparent, call your carrier  
claims agent and do not continue with the installation until the  
carrier has reviewed the damage.  
NOTE: Read all instructions before starting installation.  
2. Lay out components to ensure you have all the required parts  
before proceeding (see “PARTS & DIMENSIONS” on page 2).  
PREPARE THE CEILING  
Because of the wide variety of possible mounting situations,  
Dukane Corporation can only provide general guidelines for instal-  
lation. Study the following information carefully, and adapt it as  
necessary to fit your specific installation.  
WARNING: Be especially aware of the weight of the equipment, and the potential for personal injury or of damage to the  
equipment if it is not adequately mounted.  
The “General Guidelines” below and the information on the follow-  
ing pages cover the most common mounting situations:  
• Suspended from an adjustable column secured to a structural cross brace in the ceiling.  
• Standard fasteners secured to a wood framing member.  
• Suspended from threaded rods that are secured to the structural cross brace  
General Guidelines  
Carefully determine the position of the Universal Ceiling Projector Mount, and its distance from the screen. This will require  
knowing the lens to screen distance (see projector specifications for set-up).  
WARNING: Improper installation can result in serious personal injury! To avoid such injury, make sure that the ceil-  
ing structural members can support a redundant weight factor five times the total weight of the equipment you intend  
to support overhead. If they cannot, the ceiling must be reinforced before you install the Universal Ceiling Projector  
Mount.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
UNIVERSAL CEILING PROJECTOR MOUNT  
INSTALLATION PROCEDURES  
There are three common methods for installing the Universal Ceil-  
ing Projector Mount Series ceiling mount. The Universal Ceiling  
Projector Mount can be suspended from an adjustable column, stan-  
dard fasteners secured to a wood framing member, or threaded rods.  
Joist  
(4) 3/8" Nut  
WARNING: Improper installation can cause serious personal  
injury! Make sure that the ceiling structural members can  
support a redundant weight factor five times the total  
weight of the equipment you intend to support overhead.  
The ceiling must be reinforced before you install the Uni-  
versal Ceiling Projector Mount if the ceiling cannot support  
a redundant weight factor five times the total weight of the  
equipment.  
Backing Block  
(4) 3/8" Washer  
Adjustable Column  
(4) 3/8" x 3"  
Grade 5 Bolt  
Installation using an adjustable column, or 1” diameter schedule 40  
steel pipe section with 1” NPT threads, requires securing the adjust-  
able column or pipe to the building structure. We suggest the use of  
a backing block or Unistrut to secure the adjustable column or pipe  
to a structural member (see Figure 2). Install the Universal Ceiling  
Projector Mount on the adjustable column or pipe as follows:  
Adjustable Column  
1. Thread the Universal Ceiling Projector Mount onto the pipe a  
minimum of 1/2” to allow for final yaw adjustment.  
(4) 3/8" Nut  
2. Using Allen wrench provided, tighten the set screw to lock the  
Universal Ceiling Projector Mount in position (see Figure 3).  
Unistrut  
(1 5/8" x 1 5/8", 12 GA.)  
3. Proceed to “PROJECTOR INTERFACE PLATE ATTACH-  
MENT PROCEDURES” on page 7.  
(8) 3/8" Washer  
(4) 3/8" X 3" Grade 5 Bolt  
Adjustable Column  
Figure 2. Examples Using Adjustable Column  
Tighten  
YAW ADJUSTMENT SCREW  
(+/- 180 DEGREES)  
Figure 3. Tighten Set Screw  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
Standard Fasteners Secured to a Wood Framing Member  
The Universal Ceiling Projector Mount can be secured to a wood  
framing member through four slotted holes in the Universal Ceiling  
Projector Mount using four 1/4” diameter lag screws or, if the area  
is accessible from above, four 1/4” diameter machine bolts, nuts,  
and washers. Install the Universal Ceiling Projector Mount as fol-  
lows:  
Joist  
Backing Block  
(4) 1/4" Hex Nut  
1. Secure the Universal Ceiling Projector Mount to the wood  
framing member.  
2. Proceed to “PROJECTOR INTERFACE PLATE ATTACH-  
MENT PROCEDURES” on page 7.  
Threaded Rod  
Using four 1/4” diameter threaded rods, the Universal Ceiling Pro-  
jector Mount can be secured to a typical unistrut, angle or channel  
assembly at the overhead structural members (trusses or I-beams)  
(see Figure 4). Install the Universal Ceiling Projector Mount as fol-  
lows:  
Universal  
Projector Mount  
(8) 1/4" Washer  
1. Secure one end of the threaded rod to the structural member.  
2. Install a 1/4-20 hex nut on each threaded rod.  
(4) 1/4" Grade 5 Bolt  
3. Install the Universal Ceiling Projector Mount on the threaded  
rod.  
(8) 1/4" Hex Nut  
NOTE: Holes in the Universal Ceiling Projector Mount allow  
socket wrench access without unit disassembly.  
(8) 1/4" Flat Washer  
(4) 1/4" Threaded Rod  
4. Secure the Universal Ceiling Projector Mount to the threaded  
rod using eight 1/4-20 hex nuts.  
Joist  
Backing  
Block  
Universal  
Projector  
Mount  
(8) 1/4" Flat Washer  
(8) 1/4-20 HEX NUT  
Figure 4. 1/4”Threaded Rod  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
PROJECTOR INTERFACE PLATE  
ATTACHMENT PROCEDURES  
Attach the bottom portion of the universal projector mount to the  
projector as follows.  
1. Loosen, but do not remove, acorn nuts securing arms of the  
universal projector mount (see Figure 5).  
2. Adjust front and back legs to mounting points. If there are only  
three mounting points, remove one leg from the mount.  
3. Adjust feet (rotate right to raise, left to lower), making sure to  
allow for proper air ventilation and the mount is level with the  
projector [some feet may need to be at different heights to keep  
the mount level (M3, M4, M5 and M6 screws and washers  
included)].  
4. If the mounting holes are closer than a five inch diameter, raise  
the feet all the way up so they will swing under the universal  
interface bracket.  
WARNING: You must use proper attaching hardware and  
installation procedures. Failure to use proper  
attaching hardware and installation procedures  
may result in equipment damage or serious per-  
sonal injury.  
5. Determine proper screw size and depth (M3, M4, M5 and M6  
included) for projector mounting and correct washers (M3,  
M4, M5 and M6 included). If proper screw size is not included  
with this unit, you must purchase the proper attaching hard-  
ware separately.  
Figure 5. Projector Interface Plate to  
Universal Ceiling Projector  
Mount Attachment  
6. Secure (loosely) back two legs of universal projector mount to  
the projector at mounting locations.  
7. Secure (loosely) front two legs of universal projector mount to  
the projector at mounting locations.  
8. Move the universal projector mount to the center of gravity of  
the projector.  
9. Make sure the threaded studs on the plate are square in relation  
to the front of the projector.  
10. Tighten screws and acorn nuts securing the legs of the univer-  
sal projector mount.  
11. Tighten hex nuts on the threaded studs to secure inserts at  
proper positions.  
Figure 6. Install the Projector Interface Plate on Your Projector  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
PROJECTOR INTERFACE PLATE  
INSTALLATION PROCEDURES  
The bracket attaches to the universal projector mount lifting and  
sliding the screws of the bracket into the slot and four vee slots of  
the universal projector mount (see Figure 5). Secure the bracket  
using provided thumb screws and route cabling as necessary. Install  
the universal projector mount on the bracket as follows:  
NOTE: It is not necessary to remove the thumb nuts from the  
studs to install and remove the projector.  
1. Install, loosely, the 10-24 thumb nuts on the 10-24 studs of the  
universal projector mount.  
2. Align the four locating slots of the universal projector mount  
with the 10-24 studs of the bracket and slide the bracket on the  
universal projector mount to the limit of the slotted holes.  
NOTE: The tapers of the thumb nuts should seat in the holes  
of the bracket.  
3. Secure the Bracket to the universal projector mount using the  
thumb nuts (tapered side down).  
4. Route cables as necessary.  
CABLE MANAGEMENT  
PROCEDURES  
1. Route cables as necessary.  
2. Secure cables using cable ties (see Figure 7).  
3. Cut and install cable wrap.  
Figure 7. Cable Routing Example  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
SECURITY INSTALLATION (OPTIONAL)  
1. Using security wrench (provided), remove 5/16” standard set-  
screw and replace using 5/16” security screw (see Figure 8).  
2. Remove two screws from bottom of Projector Interface Plate,  
preferably one from each corner.  
3. Using security wrench and security screws from All-Points  
Security package, secure Projector Interface Plate to projector.  
4. Using security wrench (provided), replace screws in Projector  
Interface Plate with undercut security screws from top from top  
plate.  
5. Remove two 1/4-20 x .5” round head carriage bolts and 1/4-20  
acorn nut caps and replace using two security screws and lock  
nut Nylocks (see Figure 8).  
Figure 8. Adding Optional Security  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Instruction Manual  
MSP-DUK9000  
PROJECTOR ALIGMNMENT INSTRUCTIONS  
The Universal Ceiling Projector Mount can be adjusted for vertical  
elevation (pitch), horizontal tilt (roll), and rotation (yaw). Once the  
desired position is located and all the screws of the Universal Ceil-  
ing Projector Mount are tightened, the projector may be removed  
from its location and replaced using the four thumb nuts without  
loosing the registration of the projector. Align the projector as fol-  
lows:  
Pitch  
Adjust pitch using the pitch adjustment screw located on each end  
of the Universal Ceiling Projector Mount. Adjust pitch as follows:  
1. Loosen the pitch adjustment screw on each side of the Univer-  
sal Ceiling Projector Mount (see Figure 9).  
2. Adjust projector angle to desired pitch.  
3. Tighten the two pitch adjustment screws.  
Roll  
Adjust roll using two 1roll adjustment screws on the face and back  
of the Universal Ceiling Projector Mount. Adjust roll as follows:  
1. Loosen the roll adjustment screw on the face and back opposite  
the pitch clamp (see Figure 9).  
2. Adjust projector to desired roll position.  
3. Tighten the roll adjustment screw.  
Yaw  
Adjust yaw by threading or unthreading the Universal Ceiling Pro-  
jector Mount on the 1” pipe. Adjust yaw as follows:  
1. Loosen the set screw (see Figure 9).  
WARNING: Do not turn the Universal Ceiling Projector Mount  
to the end of the pipe threads. The Universal Ceiling Pro-  
jector Mount, Projector Interface Plate, and projector will  
fall from the pipe if the Universal Ceiling Projector Mount  
is unthreaded too far.  
Figure 9. Pitch, Roll, and Yaw Adjustment  
2. Adjust projector by turning the Universal Ceiling Projector  
Mount on the 1” pipe to the desired yaw position.  
NOTE: Overtightening the set screw may damage threads and  
make adjusting yaw difficult. Make sure yaw adjustment is set  
before tightening set screw.  
3. Tighten the set screw.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Box Computer Accessories KV0004A User Manual
Black Box Network Hardware CSU MS User Manual
Black Box Switch 26615 User Manual
Black Decker Sander Type 1A User Manual
Bolens Tiller 300 User Manual
Breckwell Heating System Breckwell Hearth Products LUXURY SERIES User Manual
Carrier Furnace 58SX040 User Manual
CFM Corporation Indoor Fireplace 2468 User Manual
Charmglow Gas Grill CT3402W User Manual
Cisco Systems IP Phone OL 12997 01 User Manual