I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Automated Display Lift
This device complies with part 15 of the FCC rules. Operation is subject to the following 2 conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television
communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a circuit other than that to which the receiver is connected
Consult the dealer or and experienced radio/TV technician for help
CM2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
CONTENTS
INSTALLATION REQUIREMENTS .............................................................................................................. 5
Power Requirements and Wiring ............................................................................................................... 5
INSTALLATION ............................................................................................................................................5
Pre-Installation Configuration and Adjustments ......................................................................................... 5
Configuring the Mount for the Display .................................................................................................... 5
Install Display ..........................................................................................................................................7
Shelf Height Adjustment .........................................................................................................................8
Determining Minimum I.D. of Furniture ......................................................................................................10
Cable Installation and Routing ................................................................................................................... 11
Mount Installation ....................................................................................................................................... 14
ADJUSTMENTS ........................................................................................................................................... 15
Display Travel Adjustment .........................................................................................................................15
Lift Cable Tension Adjustment ................................................................................................................... 15
Drive Belt Tension Adjustment ................................................................................................................... 15
Extended Programming Capabilities ......................................................................................................... 16
IR-SE15 Programming ............................................................................................................................... 18
IR-SC33a Programming ............................................................................................................................. 19
IR-SC33a Control Features ....................................................................................................................19
Serial Communications .............................................................................................................................. 20
CM2 Hardware Reference ...........................................................................................................................22
Motor Control Hardware Information .......................................................................................................... 22
CM2 Interface Board Hardware Information .............................................................................................. 24
Dry Contact Closures .............................................................................................................................. 24
Other Dry Contact Options ..................................................................................................................... 25
Connector and Switch Assignments ....................................................................................................... 27
TOOLS REQUIRED FOR INSTALLATION
PARTS
0R
x1
I/M
O/I
x1
x1
x1
(Europe)
x1
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Potloodmerkteken
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
2. Measure the distance from the center of a bottom mounting
button to the lowest point of the display.
3. Record measurement.
INSTALLATION REQUIREMENTS
The CM2 has been designed to be mounted into a cabinet or
similar type of furnishing.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
LIFT TIPPING CAUSING SEVERE PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installers responsibility
to make certain the structure to which the lift is being
mounted is capable of supporting 4 times the weight of the lift
and all attached equipment.
1
Power Requirements and Wiring
The CM2 requires 120VAC (220/240VAC 50 Hz for European
installations) power to operate.
2
A 6’ long power cable is provided with the mount.
INSTALLATION
Pre-Installation Configuration and Adjustments
Prior to being installed, the CM2 requires the configuration of
the mount for display, cable installation and routing, and the
rough adjustment of the top cover mounting bracket.
Figure 2
IMPORTANT ! : If the dimension taken in figure 2 is greater
than 16" (406mm), the faceplate will need to be adjusted
before mounting the display. If the dimension taken in figure 2
is less than 16" (406mm) proceed to Install Display below.
To prepare the CM2 for Installation:
1. Remove mount from box.
2. Remove two wooden supports from under box.
Adjusting Faceplate Location
3. Lay two wooden supports on floor and mount to supports
using four 5/16" flat washers and four 5/16" x 2 1/2" lag bolts
(hardware provided). (See figure 1)
The CM2 is designed to allow up to 6.5" of adjustment. Up to 2"
by adjusting the faceplate location on the faceplate mounting
bracket, and up to an additional 4.5" by adjusting the faceplate
mounting bracket.
Subtract 16" from the dimension determined in figure 2. The
difference between the two is the total amount of adjustment
the faceplate will require.
Lag Bolt
Example:
Dimension from step 2 = 19.5"
19.5" - 16" = 3.5" (Amount of faceplate adjustment required)
If 2" or less faceplate adjustment is required proceed to step 5.
If more than 2" of faceplate adjustment is required proceed to
step 8.
Flat Washer
NOTE: Depending upon the amount of faceplate adjustment
required, it maybe necessary to adjust both the
faceplate and faceplate mounting bracket.
If 2" or less faceplate adjustment is required:
4. Install IR receiver. (See figure 3)
5. Plug appropriate power cord into mount and power source.
6. Using the remote control, raise lift until locknuts on back
side of faceplate can be accessed. (See figure 3)
Wooden Supports
(from bottom of box)
WARNING: PINCH HAZARD! FINGERS OR HANDS
BETWEEN MOVING PARTS CAN LEAD TO SEVERE
PERSONAL INJURY! Keep fingers and hands away from
mount when operating.
Figure 1
Configuring the Mount for the Display
Prior to installation, the CM2 needs to be configured for the
size of the display being used.
To prepare the CM2 for the display being installed:
1. Install interface bracket or mounting buttons to display
following the instructions provided with bracket.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
9. Secure faceplate to faceplate mounting bracket using two
locknuts. (See figure 6)
6
6
10
10
x2
9
Figure 5
10. Using the remote control, lower the lift until it stops.
(See figure 3)
5
4
If more than 2" of faceplate adjustment is required:
11. Raise lift following instructions in step 6. (See figure 3)
12. Loosen four nuts securing faceplate mounting bracket to
frame. (See figure 6)
13. Slide faceplate mounting bracket upward desired amount.
(See figure 6)
14. Tighten four nuts to secure faceplate mounting bracket to
frame.
Figure 3
7. Remove two locknuts securing faceplate to faceplate
mounting bracket. (See figure 4)
8. Move faceplate up one set of holes to adjust location 1" or
two sets of holes to adjust 2". (See figure 4)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SEVERE PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Make sure all four nuts are tight before
continuing installation!
1"
(25MM)
8
13
12
X4
X4
8
x2
7
14
Figure 6
Figure 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
15. Align studs in faceplate with appropriate holes in faceplate
mounting bracket and hang faceplate on bracket with studs.
16. Secure faceplate to faceplate mounting bracket using two
locknuts. (See figure 7)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
To install display:
1. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See figure 9) and (See figure 10)
2. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and "click lock"
mechanism has engaged. (See figure 9) and (See figure 10)
x2
16
Figure 7
Display Installation
1
WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY
CAN LEAD TO SERIOUS PERSONAL INJURY OR AMAGE
TO EQUIPMENT! It is the installers responsability to ensure
the total amount of weight placed on the mount does not
exceed 190lbs (86.18 kg) the maximum capaity of the CM2.
1. If lift was raised during faceplate configuration, lower the lift
until it stops using the remote control.
WARNING: PINCH HAZARD! FINGERS OR HANDS
BETWEEN MOVING PARTS CAN LEAD TO SEVERE
PERSONAL INJURY! Keep fingers and hands away from
mount when operating.
Figure 9:
1
Remove pin
1
and nuts and
move to lower holes.
1
2
A padlock or bolt may
be placed through latch
holes
Figure 10
Figure 8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
NOTE: Verify that there is at least 1" of clearance between
bottom of display and mount base.
3. If there is less than 1" of clearance, remove the display and
refer to Adjusting Faceplate Location section, and adjust
display height accordingly.
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See figure 10)
Top of Display
4
Shelf Height Adjustment
After the CM2 has been properly configured for the display and
the display installed, the shelf height needs to be adjusted to
the top of the display.
To set shelf height:
1. Using the remote control, raise lift until locknutssecuring
right and left shelf adjustment brackets can be accessed.
1
Figure 13
Display removed
for clarity
5. Shelf and shelf mounting brackets down until shelf is 1/4"
(6.5mm) above top of display.
6. Tighten four nuts to secure shelf mounting bracket in
position.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
SEVERE PERSONAL INJURY OR DAMAGE TO
EQUIPMENT! Make sure all four nuts are tight before
continuing installation!
Figure 11
2. Loosen four nuts securing right and left hand shelf
adjustment brackets to faceplate mounting bracket.
1/4" (6.5mm) min.
3. Slide shelf adjustment brackets upward until top of brackets
are positioned higher than top of display.
Display and Faceplate
removed for clarity
3
4
2
5
X4
X4
Figure 12
4. Re-install shelf assembly to shelf adjustment brackets by
aligning studs in shelf bracket with clips in shelf adjustment
brackets.
Figure 14
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
NOTE: With the mount configured for the display and the
display installed, it is now possible to calculate the
minimum I.D of the cabinet.
Cover
Determining Minimum I.D. of Furniture
1. Measure and record distance "A" in figure below.
(See figure 16)
2. Measure and record distance "B" from figure below. This is
the material thickness of the cover that will be mounted to
the CM2. (See figure 16)
3. Add measurements from step one and two together. The
total is the minimum inside height of the furniture.
4. Measure and record distance "C" in figure below. This
dimension is from the back side of the CM2 vertical
mounting bracket to the furthest point forward on the
display. (See figure 16)
Base
CAUTION: IMPROPER FIT TOLERANCES CAN CAUSE
AREAS OF MOUNT OR FURNITURE TO COLLIDE WHEN
OPERATING THE MOUNT CAUSING SERIOUS DAMAGE
TO EQUIPMENT! Always provide for adequate tolerances
when building cabinet esopecially between base and cover.
(See figure 15)
Figure 15
WARNING: EXCEEDING STATED WEIGHT LIMITS OF
THE CM2 CAN LEAD TO SERIOUS PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! The weight of furniture cover
must be calculated into the total weight being placed on the
mount a total not exceed 180lbs (82 kg) the maximum
capacity of the CM2.
C
B
C
A
Figure 16
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
Cable Installation and Routing
Cable Guide
Side Cover
The CM2 has an integrated cable management system that
allows cables to be automatically "fed out" as the lift raises, and
"reeled in" as the lift lowers while maintaining constant cable
tension.
IMPORTANT ! : The CM2 requires minimum cable lengths of
8 feet from display through lower mount.
To install cables:
1. Remove two screws securing cable guide side cover.
2. Set screws aside for reuse. (See figure 17)
3
1
x2
Figure 18
4. Loosen six cable clamps. (See figure 19)
5. Route cable(s) down through upper cable clamp.
(See figure 19) and (See figure 20)
IMPORTANT ! : Leave enough cable length available above
upper cable clamp to allow the routing and tie-down of cables
between upper cable clamp and display.
Cable Guide
Side Cover
Figure 17
3. Slide cable guide side cover away from mount and carefully
set aside.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
4
From Display
x1
5
5
6
8
4
x3
8
4
x2
7
7
9
9
10
10
Figure 19
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
6. Route cable(s) down through opening at rear of middle
cable clamp mounting bracket. (See figure 19) and
(See figure 20)
13. Slide cable guide side cover over cable guide making
certain lip on back cover plate is fully seated in groove in
cable guide side cover. (See figure 21)
NOTE: If plug on cable will not fit through opening loosen or
remove one screw securing middle cable clamp
mounting bracket to mount frame and pivot middle
cable clamp mounting bracket to the side until plug can
be routed behind bracket.
Back Cover Plate
CAUTION: Bracket mounting hardware MUST be
reinstalled and tightened before continuing with cable
installation. (See figure 20)
Cable Guide
Side Cover
x1
5
13
6
Figure 21
14. Secure cable guide top cover to mount and cable guide side
cover, using two screws.
Figure 20
7. Route cable under cable pulley and up through front cable
clamp on middle cable clamp mounting bracket.
(See figure 19)
8. Loop cable and route cable down through side cable
clamp(s) on middle cable clamp mounting bracket.
(See figure 19)
x2
CAUTION: Cables must not extend higher than 1" (25mm)
above cable mounting bracket when looped! (See figure 19)
9. Route cable(s) down through lower cable clamp(s).
(See figure 19)
14
10. Route cable through cable access opening in top of mount
base and cable access opening in side of mount base.
(See figure 19)
11. Tighten upper cable clamp making certain cables are
properly seated in clamp and are not pinched.
WARNING: OVERTIGHTENING OF CABLE CLAMPS
CAN CRUSH CABLES LEADING TO DAMAGE TO
EQUIPMENT! DO NOT over tighten cable clamps.
12. Starting at upper cable clamp and working downward,
remove slack from all cables and tighten remaining cable
clamps. (See figure 19)
Figure 22
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
7. Mark eight base mounting hole locations. (See figure 24)
8. Drill pilot holes at marked locations.
9. Mark four side bracket mounting hole locations.
(See figure 41)
10. Drill four pilot holes at marked locations.
Mount Installation
The CM2 has been designed to be mounted into a cabinet or
similar type of furnishing.
The following installation instructions assume a suitable
structure and surface exists prior to installation.
11. Secure mount base to mounting surface using eight screws.
(See figure 24)
12. Secure mount to vertical mounting surface using four
screws. (See figure 24)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
LIFT FALLING CAUSING SEVERE PERSONAL INJURY OR
DAMAGE TO EQUIPMENT! It is the installers responsibility
to make certain the structure to which the lift is being
mounted is capable of supporting 4 times the weight of the lift
and all attached equipment.
X4
9
IMPORTANT ! : The finished furniture with display on and
mount fully raised must be able to be placed at a 10° angle front
and back without tipping.
X4
10
To install the CM2:
1. If the display is installed and cables routed, disconnect
wires and cables from display, uninstall top shelf and
display.
12
2. Remove mount from wooden supports used during mount
setup and configuration.
8
WARNING: MOUNT WEIGHS IN EXCESS OF 40LBS!
Always use two people and proper lifting techniques when
installing or positioning mount.
X8
11
3. Determine base position within furnishing framework.
4. Position mount until base is properly positioned and side
mounting brackets are in line with vertical supports.
(See figure 23)
5. Loosen four screws securing side mounting brackets to
mount and adjust side mounting brackets until properly
positioned against vertical mounting surface.
(See figure 24)
7
X8
6. Tighten four screws to hold position of side mounting
brackets. (See figure 24)
Figure 24
13. Install display following the procedures outlined in Install
Display section on page 7.
5
X4
X4
6
3
Figure 23
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
ADJUSTMENTS
Display Travel Adjustment
The CM2 is designed to allow the adjustment of both "Extend"
and "Retract" display travel limits. The CM2 is shipped set at
maximum extension and retraction.
There is an upward travel limit adjustment screw and a
downward travel limit adjustment screw located on the top right
hand side of the mount. (See figure 25)
NOTE: 10 full turns of the "Extend" or "Retract" travel
adjustment screws is equal to 1" of display travel.
1. Turning the "Extend" travel adjustment screw clockwise will
increase the amount of display upward travel. Turning the
"Extend" adjustment screw counter-clockwise will decrease
the amount of display upward travel.
2. Turning the "Retract" travel adjustment screw clockwise will
decrease the amount of display downward travel. Turning
the "Retract" adjustment screw counter-clockwise will
increase the amount of display downward travel.
Figure 26
Drive Belt Tension Adjustment
Drive belt tension is preset at the factory and should not need
adjustment during initial mount installation or operation.
However, after extended use it may be necessary to make
minor adjustments to belt tension. (See figure 27)
NOTE: If during operation the lift moves slower than normal or
is not raising and lowering smoothly or making unusual
noise, belt tension may need to be adjusted.
EXTEND
1
Drive belt tension is adjusted by turning an adjustment screw
located on the lower back side of the mount using a 3/16" hex
wrench. (See figure 27)
RETRACT
2
WARNING: OVERTENSIONING CAN LEAD TO DAMAGE
TO EQUIPMENT! DO NOT overtension! Adjust drive belt
tension in small increments.
Turning the screw clockwise to will increase drive belt tension
and counter-clockwise will decrease drive belt tension.
Figure 25
Lift Cable Tension Adjustment
Lift cable tension is preset at the factory and should not need
adjustment during initial mount installation. However, after
extended use it may be necessary to make minor adjustments.
If there is visible slack in cables or a rattling sound can be heard
in the area of the cable guides, cable tension may need
adjustment.
Cable tension is adjusted by turning an adjustment screw
located on the top left hand side of the mount using a hex
wrench. (See figure 26)
Turning the screw clockwise to will increase cable tension and
counter-clockwise will decrease cable tension.
Figure 27
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
Lift Column Bearing Adjustment
The upper and lower lift columns are aligned using two lift
bearings, one upper and one lower.
Bearing adjustment is pre-set at the factory, however, there
may be times when it is required to make slight adjustments in
bearing tightness to eliminate excess play in lift columns or
noise.
Upper Lift Column
Bearing Adjustment Points
WARNING: OVERTENSIONING CAN LEAD TO DAMAGE
TO EQUIPMENT! DO NOT overadjust!
IMPORTANT ! : Display should be installed on mount prior to
performing lift colimn bearing adjustment!
To adjust lift column bearings:
1. Determine if it is the upper or lower lift column that requires
adjustment.
2. Using a hex wrench, turning in small increments evenly
across all adjustment screws, loosen or tighten adjustment
screws.
Upper Lift Column
Bearing Adjustment Points
(two front and two rear)
3. Run Display to fully up, and fully down position and verify
proper lift column movement.
4. Repeat steps 1 through 3 until desired lift column movement
is achieved.
Figure 28
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
Normal Operating Mode
Extended Programming Capabilities
The CM2 allows for extended programming to make the mount
compatible with other devices such as a Universal Remote or
other control devices through a serial connection.
KEY FUNCTION
REQUIRED ACTION
PRESS ONCE
PRESS AND HOLD
N/A
1
2
MOVE DISPLAY TO HOME
EXTEND DISPLAY
NOT USED
Setting or changing the configuration of the CM2 is done
through the remote control provided with the mount.
3
4
NOT USED
N/A
The remote control has a range of 20-30ft (6-9m), and is
powered by 2 AAA batteries that are accessed from the back of
the remote.
5
RETRACT DISPLAY
PRESET POSITION 1
PRESET POSITION 2
PRESET POSITION 3
SAVE PRESET POSITION
STOP*
PRESS AND HOLD
NOT USED
6
NOTE: If operation of the mount is required at a greater
distance than remote control will allow, the mount can
be controlled through a hardwired switch or similar
divice. See Dry Contact Closures on page 24 and
(See figure 33) .
7
NOT USED
8
NOT USED
9
NOT USED
10
PRESS ONCE
The following table and illustration identify mount functionality
and response by button on the remote control(s).
NOTE: To restore mount to factory default settings, enter
setup mode and press the "PRESET III" button four
times.
IMPORTANT ! : Power must be provided to mount and IR
receiver must be installed in order to access extended
programming options.
5
1
1
5
9
3
6
4
2
3
4
2
6
8
9
10
7
7
8
MODEL: SE15
MODEL: SC33A
Figure 29 Remote Control Function
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
NEC Protocol:
Table 1-1: IR System Code
The modulated carrier is usually derived from 455kHz and is
1/12 of the frequency with 1/3 duty cycle.
Switch # 2
Switch # 1
Off
Switch # 3
Off
Custom Code
6E
When data are transmitted repeatedly, the frame cycle is
107.9ms or 186 period.
Off
Off
On
On
Off
Off
On
On
A frame consists of a syn pulse, an eight-bit custom code, an
eight-bit inverted custom code, an eight-bit data code and an
eight-bit inverted data code.
On
Off
Off
E1
E2
Off
On
Off
On
On
On
On
E3
E4
E5
E6
E7
The timing definitions of the output code waveform are shown
below.
Off
On
Off
On
IR code is selected by Dipswitch settings, dipswitches are
located next to power inlet.
Figure 30
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
IR-SE15 Programming
IR-SE15 Control Features:
•
•
•
Carrier Frequency:38KHz
Protocol:NEC - Full Repeat
System Code(s):6E (Default) - Multiple Codes
Selected via Key-Press (see below)
Table 1-2: IR-SE15 Control Codes
Key Number
Key Name
HOME
Hex Code
1
2
02
1A
07
09
0A
0B
0D
12
13
14
SAVE
3
UP
4
LEFT
5
STOP
6
RIGHT
7
DOWN
PRESET 1
PRESET 2
PRESET 3
8
10
12
To Change System Code:
1. Press and Release Key 3 + 7 (Enter Setup Mode)
2. Press and Release Key 8
3. Press and Release Key 10
4. Press and Release Key 12 - LED Blinks Twice <Quick>
5. Select System Code - See Table Below
2
6
1
4
6. Press and Release Key 2 - LED Blinks 4 times <Quick>
(Exit Setup Mode)
3
5
7
Table 1-3:
System
Code
Press +
Release
6E (Default)
8
8,8,8,8
10
E1
E2
E3
E4
E5
E6
E7
8
10
12
10,8
10,8,8
10,8,8,8
10,8,8,8,8
12
Figure 31
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
IR-SC33a Programming
IR-SC33a Control Features
•
•
•
Carrier Frequency: 38KHz
Protocol: NEC - Full Repeat
System Code: 6E
Table 1-4:
Key Number
Key Name
HOME
Hex Code
3
02
07
09
0B
0D
12
13
14
1A
8
RETRACT
LEFT
10
12
14
19
20
21
27
RIGHT
EXTEND
PRESET 1
PRESET 2
PRESET 3
SAVE
3
8
12
10
19
14
20
21
27
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
Serial Communications
NOTE: Check with the appropriate automation system vendor for available drivers and/or software for any external devices.
Notes:
[PR] = Product ID (CM2 = 02)
[AD] = Address (see address description & table)
[CR] = ASCII Carriage Return
[CH] = Check Code
[ST] = Status (see status table)
Connecctions to be made to 9 pin connector as follows:
RS-485 REF
RS-485 +
RS-485 -
Pin 7
Pin 8
Pin 9
Communication parameters as specified in ANSI TIA/EIA-485-A:
Baud Rate:
Data Length:
Parity:
9600
8 Bits
None
1
Stop Bit:
Flow Control:
None
Command Table:
Action:
Extend
Command:
Expected Response:
>[PR][AD]0E[CH][ <[ST][CH][CR] & unit should Extend
CR]
Retract
>[PR][AD]10[CH][ <[ST][CH][CR] & unit should Retract
CR]
Cancel Move
Poll for Status
Get Model #
>[PR][AD]03[CH][ <[ST][CH][CR] & unit should Stop
CR]
>[PR][AD]01[CH][ <[ST][CH][CR]
CR]
>[PR][AD]66[CH][ <(unit model #)[CH][CR]
CR]
Get Operation
Count
>[PR][AD]64[CH][ <[ST](4 digit hex operation count)[CH][CR]
CR]
Get Software
Revision
>[PR][AD]67[CH][ <[ST](4 digit revision level)[CH][CR]
CR]
Get Serial #
>[PR][AD]68[CH][ <(10 digit unit serial #)[CH][CR]
CR]
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
Address Description:
Multiple Chief devices can be used on the same network by setting each device to a different address.
Note: All units ship with a default address of 0
Address Table:
Addresses are set using dipswitches located next to power inlet on mount. (See figure 32)
Switch # 6
OFF
ON
Switch # 7
OFF
OFF
ON
Switch # 8
OFF
OFF
OFF
OFF
ON
Address
00
01
OFF
ON
02
ON
03
OFF
ON
OFF
OFF
ON
04
ON
05
OFF
ON
ON
06
ON
ON
07
Status Table:
Status is a 4 character hex representation of a 16 bit value
Bit
0
1
0
Description
TRUE
FALSE
In Home Position?
1
TRUE
FALSE
Move in Progress?
2
TRUE
FALSE
Network Operation in Progress?
Parameter Changes Enabled?
Network Command Error?
Not Used - Permanently @ 0
Not Used - Permanently @ 0
Not Used - Permanently @ 0
At Extend Limit
3
TRUE
FALSE
4
TRUE
FALSE
5
-
-
6
-
-
7
-
-
8
TRUE
FALSE
9
TRUE
FALSE
At Retract Limit
10
11
12
13
14
15
-
-
-
-
-
-
-
-
-
-
-
-
Not Used - Permanently @ 0
Not Used - Permanently @ 0
Not Used - Permanently @ 0
Not Used - Permanently @ 0
Not Used - Permanently @ 0
Not Used - Permanently @ 0
Example:
Fully retracted, parameter changes disabled, no errors, not moving, in home position.
0, 0, 0, 0, 0, 0, 1, 0, 0, 0, 0, 0, 0, 0, 0, 1
Value returned as status: 0201 (hex)
Errors:
If no response message is received, the device does not exist on the network, or there was an error during message transmission
See Error Message Table
Error Message Table:
0x01 Command Not Supported Returned when a device does not support the command sent
0x02 Index Error
Returned when the index value sent is out or range for the device
0x03 Value Error
Returned when the data value sent is out of range for the device
0x04 Message Length Error
0x05 Write Protect Error
Returned when the length of the command message is incorrect for the command code
Returned when parameter changes are attempted without first enabling parameter changes
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
CM2 Hardware Reference
Motor Control Hardware Information
(See figure 32)
RS485 Network Programmable Paramaters and Status Bit Assignments
RS485 Network Programmable Parameters
Parameter
Identifier
Name
Range
Factory Default
Units
0
Custom Code
1-32687
100-6000
1-100
0
-
1
2
3
4
5
6
7
Maximum Movement Time
Extend Speed
3100
100
100
100
100
100
100
0.01 sec
%
Retract Speed
1-100
%
Ramp UP Time
10-100
10-100
31-300
31-300
0.01 sec
0.01 sec
1 sec
1 sec
Ramp DOWN Time
Show Extend Delay
Show Retract Delay
RS485 Network Status Bit Assignments
Name
Bit
Bit Location
0
1
2
3
4
8
9
At Home Position
- - - - - - - - - - - - - - - X
- - - - - - - - - - - - - - X -
- - - - - - - - - - - - - X - -
- - - - - - - - - - - - X - - -
- - - - - - - - - - - X - - - -
- - - - - - - X - - - - - - - -
- - - - - - X - - - - - - - - -
Move in Progress
Network Operation in Progress
Parameter Write Operations Enabled
Network Command Error
At Extend Limit
At Retract Limit
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
1st Position of switch array
1st Position of connector array
1st Position of connector array
Figure 32 CM2 Connectors and Switches
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
CM2 Interface Board Hardware Information
(See figure 32)
Dry Contact Closures
The unit provides dry contact outputs for system feedback, or to control other devices.
To complete circuits to external devices:
7. Connect the common wire from your switch to terminal 7. (See figure 33)
8. Connect the 'up' wire from your switch to terminal 5.
9. Connect the 'down' wire from your switch to terminal 6.
Figure 33
J1
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Isolated Extend/Retract Input (+)
Isolated Extend/Retract Input (-)
Isolated Voltage Sense Input (+)
Isolated Voltage Sense Input (-)
24V DC Supply Out (150ma Max.)
Ground
RS485 Ref.
RS485 (+)
RS485 (-)
J2
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin14
Not Used
Not Used
Not Used
Not Used
Move Extend Terminal Input
Move Retract Terminal Input
Ground
Extend Error Input
Retract Error Input
Ground
Extend Limit Out
Extend Limit Out Return
Retract Limit Out
Retract Limit Out Return
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
Other Dry Contact Options
Extend Retract with Single Switch
Pins 1 and 2 on 9 pin Connector. (See figure 32) and (See figure 34)
Figure 34
Voltage Sense External Power Source
Unit extends and stays extended when voltage from an external source is applied across pins 3 and 4 on connector J1. When
voltage is removed unit retracts. (See figure 32) and (See figure 35)
Figure 35
Voltage Sense Internal 24V DC Power Source
The 24V DC power supply that is built into the unit can be used to power external devices by using pins 5 and 6 on connector J1.
NOTE: Using this input will force a complete UP/DOWN cycle of the unit. No other inputs, with the exception of error inputs, are
available until the cycle has completed. (See figure 32) and (See figure 36)
Figure 36
Extend Error Input
NOTE: Units are shipped with error contacts "Normally Open". To set unit to respond to "Normally Closed" error contacts contact
a Chief Technical Support representative by calling 1-800-582-6480, or by visiting www.chiefmfg.com.
When unit receives an Extend error signal during an extend operation, the unit will immediately stop and reverse direction.
(See figure 32) and (See figure 37)
J2
Figure 37
25
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
Retract Error Input
NOTE: Units are shipped with error contacts "Normally Open". To set unit to respond to "Normally Closed" error contacts contact
a Chief Technical Support representative by calling 1-800-582-6480, or by visiting www.chiefmfg.com.
When unit receives a Retract error signal during a Retract operation, the unit will immediately stop and reverse direction.
(See figure 32) and (See figure 38)
J2
Figure 38
Extend Limit Option
Internal set of dry contacts close when unit is fully extended.
Contact Rating: 30V AC or DC 1A max.
(See figure 32) and (See figure 39)
Figure 39
Retract Limit Option
Internal set of dry contacts close when unit is fully retracted.
Contact Rating: 30V AC or DC 1A max.
(See figure 32) and (See figure 40)
Figure 40
NOTE: Multiple control features can be used at the same time with the exception of the "Voltage Sense" feature.
Example: IR or Serial control along with a momentary pushbutton for service and a discreet UP/Down wall switch for operation.
IMPORTANT ! : When using multiple control features make sure ALL contacts are momentary and "Normally OPEN"
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
Connector and Switch Assignments
All Dipswitches are in the "OFF" position when shipped from factory.
SW1
Switch 1
Switch 2
Switch 3
Switch 4
Switch 5
Switch 6
Switch 7
Switch 8
IR
IR
IR
Not Used
Not Used
485 Address
485 Address
485 Address
IR System Code Select Logic
Switch Settings (Sw 1-3)
Select 2
OFF
OFF
OFF
OFF
ON
Select 1
OFF
OFF
ON
Select 0
OFF
ON
IR System Code
6E
E1
E2
E3
E4
E5
E6
E7
OFF
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
RS485 Address Select Logic
Switch Settings (Sw 6-8)
Select 2
Select 1
Select 0
RS485 Network
Address
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
0
1
2
3
4
5
6
7
OFF
ON
ON
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
Figure 41
Troubleshooting
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Lift does not respond
Verify Power to Mount
Normal Operation
•
•
No Power to Mount
12V trigger option being
used
See "Low Voltage Sensing" section
•
Overheated motor
Allow motor to cool for 10 to 15
minutes
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
CM2
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CM2
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8820-000016 RevF
¤2008 Chief Manufacturing
01/08
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|