6159939130
CS7000 Controller
Hardware Overview Manual
With Ethernet/CCM Information
for use with
177 and 277 Series Electric Fastening Tools
CP Ref. / NO : 6159939130
Techmotive P/N : 39-30-41365
December 2005
CP Techmotive
22705 Heslip Drive
Novi, Michigan 48375 USA
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
CP Techmotive warrants its PRODUCTS to be free from defects in materials and workmanship for the lesser of (1)
one year from the date of shipment from the manufacturing facility in Michigan, U.S.A. OR
(2) one-million cycles except for the products noted below:
250,000 cycles
CP Techmotive crowfoot, tubenut and hold & drive heads
3rd-party crowfoot, tubenut, hold-and-drive torque multiplier or other heads
manufacturer’s warranty
500,000 cycles
56 and 116 Series nutrunners
PRODUCTS include CP Techmotive brand fastening tools, controllers and cables, GSE brand sensors and
instruments, and anti-lock brake testing systems. Fuses and batteries are not covered under warranty.
For PRODUCTS verified as defective at CP Techmotive’s manufacturing facility, CP Techmotive shall have the
option, in its sole discretion, to repair or replace the products or components. CP Techmotive shall not be liable for
any installation charges, expenses of the Buyer for repairs or replacement, damages from delay or loss of use, or
other indirect or consequential damages of any kind. The warranty does not cover any product that has been
modified without the approval of CP Techmotive, used for a purpose other than that for which it was intended, used
in a manner inconsistent with any instructions, subjected to unusual physical stress, environmental or electrical
conditions, or whose original identification marks have been removed or altered.
Whenever the PRODUCTS are to be incorporated in a system, the design of which originated with the Buyer,
CP Techmotive only that the PRODUCTS shall be free of defects in materials and workmanship and offers no other
warranty.
In the event that a product is repaired or replaced under the terms of the warranty, the warranty period for the
repaired or replacement product shall be limited to the remaining portion of the original warranty.
Any warranty extended by the original manufacturer of peripheral equipment, such as printers, recorders, plotters,
etc., included with a CP Techmotive product or system shall be extended to the Buyer and shall be the only warranty
offered.
Transportation charges for materials shipped to the manufacturing facility for warranty repair are to be paid by the
Buyer. CP Techmotive will pay for shipping to return items repaired or replaced under warranty.
THIS LIMITED WARRANTY IS EXCLUSIVE, AND CP Techmotive MAKES NO OTHER WARRANTY OF ANY KIND
WHATSOEVER, WHETHER EXPRESSED, IMPLIED OR STATUTORY, WITH RESPECT TO THE PRODUCTS OR
PARTS MANUFACTURED BY IT, WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR ANY OTHER MATTER OR WARRANTY OF ANY KIND. No agent, employee or representative of
CP Techmotive has the authority to bind CP Techmotive in any affirmation, representation, or warranty concerning
the Products or parts except as stated herein.
THIS REMEDY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE FOR ANY NONCONFORMITIES IN
MATERIALS OR WORKMANSHIP, OR FOR ANY DAMAGES RESULTING FROM ANY OTHER CAUSE
WHATSOEVER. CP Techmotive SHALL NOT, IN ANY EVENT, BE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, NATURE OR DESCRIPTION, WHETHER FOR
NONCONFORMITIES IN MATERIALS OR WORKMANSHIP UNDER ANY WARRANTY, IN CONTRACT, TORT,
NEGLIGENCE, STRICT LIABILITY, OR FOR ANY OTHER REASON.
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER SATISFACTION
Please Read This!
As a valued customer, your opinion and satisfaction are important to CP Techmotive. Please let
us know what you think of our product(s).
Write the part number and serial number of the product(s) you have purchased before you begin
our brief online survey. The numbers are located on a sticker affixed to the handle of the
nutrunner or screwdriver, and exterior or interior of the controller.
Tool Label
Part Number
Serial Number
Controller Label
Part Number
Serial Number
To complete the survey:
2. Click the Customer Satisfaction Survey link located below the gray buttons in the red, left-
hand frame.
3. Fill in the fields and click the appropriate choices.
4. Click the Submit to GSE tech-motive tool button
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Preface
The CS7000 Controller manufactured by CP techmotive is a component of one of the most powerful
DC electric nutrunner fastening control systems available. The system uses 100% digital technology
to ensure accurate and reliable fastening and data acquisition. Microprocessors in both the fastening
tool and the controller s tool control module (TCM) enable the system to perform to levels of
accuracy while providing easy set-up and operation previously unattainable.
With Intelligent tool technology you no longer need to enter tool identification, calibration, angle
counts, speed and other information. You simply plug in the tool, power on the system, program the
desired tightening specifications and begin production.
A complete nutrunner fastening control system is made up of the CS7000 Controller, a cable and a
CP techmotive 177 or 277 Series nutrunner. The powerful CP techmotive Visual Supervisor software
program is used for system setup, fastening, data collection, and diagnostics.
Who Should Use This Manual
This manual is written for the engineers, technicians and users who will set-up and/or operate the
CS7000 Controller with any of the Intelligent (177 and 277 Series) nutrunners.
How to Use This Manual
This manual provides installation, maintenance and technical information about the CS7000
Controllers.
This Preface provides conventions and abbreviations used throughout this manual.
If you have never used a CS7000 Controller, read this manual entirely. The first two chapters will
help you become familiar with safety requirements, the location of components, software and
features.
If you are already familiar with the CS7000 Controller, look over Chapter 3. Installing the CS7000
Controller and Chapter 4. Technical Information, which describe the power requirements, details of
the I/O wiring and connectors, replacement parts and fuses.
December 2005
i
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Conventions
The following conventions are used throughout this manual for the safety of personnel, equipment,
software, and data. The conventions include warnings, cautions and notes, as follows:
WARNING! It can be dangerous to personnel and/or machine systems,
if operating instructions are not followed. The information
!
appears in a box in italicized boldface type.
CAUTION!
There may be damage to equipment, and loss of software
and data, if operating instructions are not followed. The
information is indented and in italicized boldface type.
NOTE:
Information that adds to your knowledge of the equipment
and/or software. The information is indented and italicized.
?
____________________________________________________________________________________________
Page ii 39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Abbreviations
Some of the most common abbreviations used throughout this manual include the following:
API
application program interface
electro-static discharge
ground fault circuit interrupter
input/output
ESD
GFCI
I/O
IEC
International Electrotechnical Commission
Institute of Electrical and Electronic Engineers
internet protocol
IEEE
IP
kbps
kVA
LAN
LED
mbps
PCI
kilo-bits per second
kilovolt-ampere
local area network
light emitting diode
million bits per second
peripheral component interconnect
tool control module
TCM
TCP/IP
RAM
SDLC
STM
TINI
V
transmission control protocol/internet protocol
random access memory
synchronous data link control
standard test method
tiny internet interface
volts
VS
Visual Supervisor is the setup, fastening, data collection, and diagnostics software
program designed by CP techmotive
____________________________________________________________________________________________
December 2005 Page iii
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
(This page is left blank intentionally.)
____________________________________________________________________________________________
Page iv 39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Who Should Use This Manual...............................................................................................i
How to Use This Manual........................................................................................................i
Conventions ...........................................................................................................................ii
Abbreviations........................................................................................................................iii
Contents..................................................................................................................................v
Figures ..................................................................................................................................vii
Tables....................................................................................................................................vii
1. Think Safety First! ..............................................................................................................1-1
General Machine Safety................................................................................................1-1
Electrical Safety .............................................................................................................1-3
2. Identifying the Components..............................................................................................2-1
Front Panel ..........................................................................................................................2-2
Latch........................................................................................................................2-3
Rotary Actuator .......................................................................................................2-3
Parameter Select Switch ........................................................................................2-3
LED Display.............................................................................................................2-3
Top Panel.............................................................................................................................2-4
Bottom Panel.......................................................................................................................2-4
Tool Connector........................................................................................................2-5
Input AC Power.......................................................................................................2-5
Printer/Barcode Connector.....................................................................................2-5
RS-232 Connector (VS Setup)...............................................................................2-5
SDLC/485 I/O Network Connector (Optional)........................................................2-5
Ethernet (10Base-T) and 9-pin D (Communications/Diag) Setup ........................2-5
I/O Connector..........................................................................................................2-6
Enclosure Interior...............................................................................................................2-6
Gen2 Tool Control Module (TCM).................................................................................2-8
Servo Amplifier........................................................................................................2-9
Gen2 Device Control Module (DCM) .....................................................................2-9
Communications Control Module (CCM) “Optional”........................................... 2-10
Backplane.................................................................................................................... 2-11
Backplane Fuses.................................................................................................. 2-11
DIP Switch Settings ............................................................................................. 2-12
Power Supply.............................................................................................................. 2-12
Ground Fault Circuit Interrupter (GFCI)..................................................................... 2-12
Disconnect Switch....................................................................................................... 2-13
Circuit Breaker/Fuses ................................................................................................. 2-13
3. Installing the CS7000 Controller ......................................................................................3-1
Mounting the CS7000 Controller......................................................................................3-1
Emissions and Susceptibility ...........................................................................................3-2
Meeting the AC Input Power Requirements ...................................................................3-3
Input Power Protection......................................................................................................3-3
December 2005
v
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Grounding........................................................................................................................... 3-4
I/O Wiring ............................................................................................................................ 3-4
Connector Pinout Definitions........................................................................................... 3-8
Tool Connector “26 pin” (Metal SMC) – Front View .................................................... 3-8
I/O Connector – Front View.......................................................................................... 3-9
TCM (IN and OUT) Network Connectors – Front View............................................... 3-9
RS-232 Connector – Front View .................................................................................. 3-9
Printer/Computer/Diagnostics (RS-232) Connector – Front View ............................ 3-10
Programming the CS7000 Controller (In General)...................................................... 3-10
Programming the CS7000 with Ethernet (CCM).......................................................... 3-10
4. Technical Information ....................................................................................................... 4-1
Replacement Parts............................................................................................................. 4-1
Cleaning the Enclosure Window ..................................................................................... 4-1
Assembly Drawings........................................................................................................... 4-1
Contact Information........................................................................................................... 4-2
5. Index .................................................................................................................................... 5-1
____________________________________________________________________________________________
Page vi
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figures
Figure 2-1.
Front Panel View..................................................................................................2-2
Turning the Rotary Actuator to the ON Position .................................................2-3
Top Panel View ....................................................................................................2-4
Bottom Panel View...............................................................................................2-4
Components Inside the Enclosure of the CS7000 Controller ............................2-7
Front View of the TCM .........................................................................................2-8
Communications Control Module (CCM) ......................................................... 2-10
CS7000 Controller Backplane .......................................................................... 2-11
Ground Fault Circuit Interrupter........................................................................ 2-12
CS7000 Controller Dimensions of the Front and Bottom Panel.........................3-2
Remote Input Circuit Schematics ........................................................................3-7
Figure 2-2.
Figure 2-3.
Figure 2-4.
Figure 2-5.
Figure 2-6.
Figure 2-7.
Figure 2-8.
Figure 2-9.
Figure 3-1.
Figure 3-2.
Tables
Table 3-1.
Table 3-2.
Table 4-1.
19-Position Remote I/O Connector Pinout Signal Names and Descriptions.....3-4
Guidelines for Proper Operation of the Controller I/O Signals...........................3-7
Replacement Parts...............................................................................................4-1
____________________________________________________________________________________________
December 2005 Page vii
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
(This page is left blank intentionally.)
____________________________________________________________________________________________
Page viii 39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Think Safety First!
1. Think Safety First!
Working with fastening tools can be dangerous if safe and proper procedures are not followed. As
with all machinery, certain hazards can be involved with the operation of the product. Using these
tools with respect and caution will considerably lessen the possibility of personal injury. If, however,
safety precautions are overlooked or ignored personal injury to the operator can result.
Always use common sense and exercise caution when using these tools. They can produce high
torque that, unless properly compensated for, could cause personal injury. Remember, your personal
safety is your responsibility.
If you are an operator or CP techmotive-qualified service technician, you should become familiar with
the contents of this manual before operating, servicing, or maintaining any part of the CS7000
Controller. Familiarization with all components of the system can minimize the possibility that an
accident or injury might occur.
CP techmotive assumes no responsibility for personal injury or damage to equipment resulting from
misuse of these tools. After reviewing this manual you should also review all safety procedures
provided by your company and the equipment installer.
WARNING! Failure to follow these steps can result in serious personal
injury.
!
General Machine Safety
•
FOR YOUR OWN SAFETY READ THE INSTRUCTION MANUAL THOROUGHLY
PRIOR TO OPERATING THE TOOL.
•
DO NOT WORK IN A DANGEROUS ENVIRONMENT. Do not use power tools in a
damp or wet location or explosive atmosphere, or expose them to rain, oils, or corrosive
fluids.
•
•
KNOW THE LOCATION OF POWER DISCONNECTS AND EMERGENCY STOP
BUTTONS PRIOR TO OPERATING THIS EQUIPMENT.
KEEP ALL ELECTRICAL PANELS CLOSED DURING OPERATION. High voltage
present inside enclosure panels can result in personal injury. Do NOT bypass or defeat
electrical safety devices. Turn the power actuator to the OFF position prior to any
servicing or maintenance of the controller.
•
•
Observe all government and/or company power lockout standards.
NEVER OPERATE SOLENOID VALVES, LIMIT SWITCHES OR RELAYS
MANUALLY as this practice can create dangerous, unexpected machine movements.
December 2005
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
•
SECURE THE TOOL. Tools that develop torque can produce hazardous torque
reactions. Always be sure that the tool is properly fixtured to absorb reaction as a
fastener is tightened. Never operate a tool capable of high torque without proper
fixturing.
•
•
SECURE WORK. Avoid situations where the part being fastened breaks loose and can
cause damage.
NEVER TOUCH OR ATTEMPT TO STOP MOVING MACHINERY OR PARTS
WITH YOUR HANDS, OTHER PARTS OF YOUR BODY, OR MAKESHIFT
DEVICES.
•
•
DO NOT OPERATE THE TOOL WHILE UNDER THE INFLUENCE OF ALCOHOL,
DRUGS OR MEDICATION THAT CAN IMPAIR YOUR JUDGMENT.
REPORT ALL UNSAFE WORKING CONDITIONS OR PRACTICES TO YOUR
SUPERVISOR AND / OR SAFETY DEPARTMENT FOR CORRECTION.
•
•
WEAR APPROVED SAFETY GLASSES AT ALL TIMES.
DO NOT WEAR JEWELRY, especially bracelets and rings, while operating the
fastening tools. Keep hands and fingers away from all rotating parts and avoid situations
where clothing can become tangled in the tool. Secure loose fitting clothing, neckties,
and long hair. Wear medical alert identification cautiously.
•
•
DO NOT OVERREACH. Keep proper footing and balance at all times.
KEEP YOUR WORK AREA CLEAN. Do not work on or near slippery floors or
surfaces. Avoid situations where the tool reacts against unexpected obstacles. Do not
operate electrical equipment while standing on a wet floor.
•
MAINTAIN TOOLS IN TOP CONDITION. Keep tools properly lubricated and clean.
If any wires become frayed or exposed, replace them immediately. Prevent dirt, grease
or contaminants from getting into the tool.
•
•
REDUCE THE RISK OF UNINTENTIONAL STARTING. Be careful how the tool is
left unattended. Avoid resting it on its throttle lever to prevent false starts.
CONTROL THE DIRECTION OF ROTATION. The reaction torque changes direction
when going from forward to reverse. Always be aware in which direction the tool will
rotate prior to using it. If the tool is not fixtured this will allow you to brace for the
proper direction of torque reaction.
•
CHECK DAMAGED PARTS. Before further use of a tool, any part of the tool that is
damaged should be carefully checked to ensure that it will operate properly and perform
its intended function. Check for alignment of moving parts, breakage of parts, mounting,
and any other conditions that may affect its operation. Never operate a tool that has
damaged or exposed wires. Never operate a tool that has any part of the powertrain,
other than the output spindle, exposed.
____________________________________________________________________________________________
Page 1-2 39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Think Safety First!
Electrical Safety
Only qualified and properly trained personnel should perform electrical/electronic
troubleshooting and repair. Consider the following electrical system safety guidelines:
•
Before you troubleshoot or service a fastening system station, be sure you have an up-to-
date and appropriate set of electrical drawings for that station.
•
Remove metal items, such as rings, metal necklaces, wristwatches and jewelry, as these
can create electrical hazards. Wear medical alert identification cautiously.
•
•
Wear safety glasses, but avoid wearing those that have metal rims or metal side shields.
It may be necessary to troubleshoot equipment while the power is ON. ONLY qualified,
trained personnel should do this. During these instances, open only the panels, doors, or
covers which need to be opened. Know the voltage present at all points before you begin
troubleshooting.
•
•
•
Use properly insulated tools when working on electrical equipment to reduce the
possibility of shock. Make sure the insulation is adequate to safeguard against the high
voltages present.
If you must work on the electrical system, be sure the main disconnect switch on the
power panel is in the OFF position and locked out with locks from each trade involved
in the repair.
Do not attempt to modify or repair the machine without the approval of the proper
authorities.
•
•
•
Use approved fuse pullers when changing fuses.
Never use jumper wires or fuse substitutes to replace specified fuses.
Always use fuses of a capacity smaller than or equal to the safe capacity of the line or
the equipment it serves.
•
•
Before you work on any circuit, check it with an appropriate testing device to be sure
voltage is not present.
Install temporary wiring as safely as possible and replace it with permanent wiring as
soon as possible. Install grounding wherever it is needed in the final installation. If
modifications are made to the system wiring, drawings must be revised to illustrate this
change.
•
Know how to deal with electrical fires properly. Keep carbon dioxide and powder
extinguishers handy.
____________________________________________________________________________________________
December 2005 Page 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
(This page is left blank intentionally.)
____________________________________________________________________________________________
Page 1-4 39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
2. Identifying the Components
This chapter is designed to familiarize you with the components of the CS7000 Controller. It has four
sections to help you locate all the major components easily:
•
•
•
•
Front Panel
Top Panel
Bottom Panel
Enclosure Interior
Each section includes figures that call out the components. Descriptions of the components follow the
figures.
December 2005
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Front Panel
Figure 2-1 shows the front panel components of the CS7000 Controller. Descriptions are provided in
clockwise order, starting with the latch.
Figure 2-1.
Front Panel View
Page 2-2
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
Latch
The latch keeps the front panel of the controller closed. To open it you need a key
(part number 31-80-0414).
Rotary Actuator
The rotary actuator is a safety device that allows you to open the enclosure door only when the
disconnect switch is in the OFF position. The rotary actuator is mechanically interlocked with the
disconnect switch, which is located inside the enclosure. The ON and OFF positions on the rotary
actuator correspond to the ON and OFF positions of the disconnect switch.
Turn the rotary actuator clockwise to turn on power to the controller. The arrow on the rotary actuator
must rotate 90 degrees from ⇐ to ⇑, as shown in Figure 2-2.
Figure 2-2. Turning the Rotary Actuator to the ON Position
Parameter Select Switch
The parameter select switch selects the next parameter set that will be used by the tool. The limits for
the parameter set are specified using Visual Supervisor (VS). This switch lets you select up to 8
different parameter sets even though the controller is capable of more.
LED Display
The LED display shows you the torque, or torque and angle value for the most recent rundown. It also
scrolls messages for the operator. For example, if a barcode scan is required before the next rundown,
the operator sees a barcode prompt on the LED display.
____________________________________________________________________________________________
December 2005
Page 2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Top Panel
Figure 2-3 shows the top panel components of the CS7000 Controller.
Figure 2-3.
Top Panel View
Bottom Panel
Figure 2-4 shows the bottom panel components of a CS7000 Controller. Connector configurations
will vary depending on the model.
Figure 2-4.
Bottom Panel View
Page 2-4
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
Tool Connector
A 26 position metal (SMC) connector is the interface between the 177 and 277 Series nutrunner cable
and control electronics. Refer to Connector Pinout Definitions in Chapter 3. Installing the CS7000
Controller for pinout details.
Input AC Power
The CS7000 Controller is shipped with a 6-ft power cable with Hubble connector 2321-CY. Power is
220 VAC. Refer to Chapter 3 for details.
Printer/Barcode Connector
The nine-position asynchronous RS-232 serial output connector allows you to use a printer. The
printer can be used to generate hard copies of torque, or torque and angle readings upon command
from the controller. This port can also be used to receive barcode information.
RS-232 Connector (VS Setup)
The nine-position asynchronous RS-232 serial output connector allows you to communicate with the
controller using a laptop computer. The laptop computer runs the VS software program that allows
you to program torque, or torque and angle limits and operating modes into the controller. Refer to the
Visual Supervisor User s Guide (part number 39-30-34823) for details.
NOTE:
The laptop computer also allows you to program (also referred
to as ‘flash’) the latest device control module (DCM) and tool
control module (TCM) firmware into the controller.
?
SDLC/485 I/O Network Connector (Optional)
The 10-position female SDLC/485 connector enables a permanent network connection to and from
the controller, other controllers in the network and a permanently connected computer
Ethernet (10Base-T) and 9-pin D (Communications/Diag) Setup
These connectors are available on some versions for providing Ethernet connectivity to a LAN as well
as providing a port for configuring the Ethernet/communications functions. At present, the 9-pin-D is
configured as an RS232 port running at 9600 baud (8 data, 1stop, no parity) and will interface directly
with a terminal emulator program (hyperterminal etc.)
____________________________________________________________________________________________
December 2005
Page 2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
I/O Connector
The 19-position remote I/O connector provides the interface between external control/monitoring
devices and the internal control electronics. CP techmotive accessories, such as socketrays, are
connected here.
The mating connector for this port is a 14-shell, 19-pin, strain relief (SR) connector
(part number 23-10-5200). The mating connector enables connection of your own remote control
and/or monitoring devices, such as external annunciator lamps or remote cycle-on contacts. Refer to
I/O Wiring in Chapter 3. Installing the CS7000 Controller for pinout details.
Enclosure Interior
The enclosure interior for the CS7000 Controller includes the following components and sub-
components:
•
Sub-panel, that includes:
•
•
•
•
Disconnect switch
Power supply (24 VDC)
Circuit breaker/ Fuses
Ground fault circuit interrupter (GFCI)
•
Backplane, that includes:
•
•
•
Address switch
DCM fuse (internal DCM power)
I/O power (24 VDC) fuses
•
TCM, that includes:
•
•
•
DCM control card
Servo
Communications Control Module (CCM) optionally
See Figure 2-5 on page 2-7 and Figure 2-6 on page 2-8.
Page 2-6
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
Figure 2-5.
Components Inside the Enclosure of the CS7000 Controller
____________________________________________________________________________________________
December 2005 Page 2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Gen2 Tool Control Module (TCM)
The TCM, shown in Figure 2-6, is a device that controls a single DC electric tool. The TCM and its
attached tool are referred to as a spindle. The TCM houses both the servo amplifier and DCM.
Figure 2-6.
Front View of the TCM
WARNING! This servo contains a fast discharge circuit to discharge
the internal capacitors within a few seconds. However, you
!
should still be careful when handling the TCM. A “bus
voltage present” light on the front of the unit will
extinguish when the bus voltage has dropped below
approximately 70VDC.
Page 2-8
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
The TCM has a small four-digit display, a column of nine indicator LEDs, and two potentiometers.
The LEDs provide status and condition information about the connected nutrunner. The indicator
LEDs are labeled:
•
•
•
•
•
READY
•
•
•
•
•
ANGLE HI
GOOD
ANGLE LOW
BAD
SPINDLE FAULT
SERVO FAULT
MOTOR ENABLE
PEAK TORQUE HI
PEAK TORQUE LOW
•
BUS VOLTAGE PRESENT
To understand the meaning of these LEDs and potentiometers when they are lit, refer to TCM Related
Faults in the Visual Supervisor User s Guide (part number 39-30-34823).
Servo Amplifier
The servo amplifier is a three-phase, brushless DC motor controller that provides electrical power to
the nutrunner motor. It receives control signals from the DCM. Based on the state of these inputs, the
servo amplifier energizes the motor windings to rotate the motor.
The servo amplifier serves as a closed-loop speed controller. It modulates the motor winding currents
in order to maintain a constant motor speed despite changes in load. Additionally, the servo amplifier
can stop the motor quickly by way of dynamic and/or 4-quadrant braking. The servo amplifier boards
are paired with the DCM board and are housed inside the TCM.
Gen2 Device Control Module (DCM)
A 3V lithium battery is located on the DCM board. You must remove the DCM board from the TCM
in order to replace this battery. A generic 3V lithium battery (Duracell DL 2430 or equivalent) can be
used. A jumper JP1 located near the back of the TCM can be removed to disconnect the battery
from the circuitry.
____________________________________________________________________________________________
December 2005
Page 2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Communications Control Module (CCM) “Optional”
The CCM module provides Ethernet (10Base-T) connectivity from the CS7000 Controller. This
interface may be to Visual Supervisor systems on the LAN or possibly custom interfaces to customer
networks. In addition the CCM (in the future) be capable of various communications functions such
as Fieldbus connections. The CCM module will also be capable of handling a keypad/display
function.
Figure 2-7.
Communications Control Module (CCM)
Page 2-10
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
Backplane
The backplane is a printed circuit board into which many of the internal component cables plug.
Figure 2-8.
CS7000 Controller Backplane
Backplane Fuses
F1 and F2 are the main 220V line fuses (MDA-20).
F4 is a 1A Pico fuse used to protect the external 24 VDC. F5 is a spare fuse.
____________________________________________________________________________________________
December 2005
Page 2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
DIP Switch Settings
DIP switch block SW1 is used to configure the SDLC address. These are binary encoded to provide
addresses 1 through 32 (zero is not a valid address). For Ethernet this address should be set to 1.
DIP switch block SW2 is for special options. Position #1 can force the unit into the FLASH program
mode. Position #2 configures the printer port for DaimlerChrysler Plant Floor Communication System
(PFCS) formatting.
Power Supply
A 1.3A, 24V power supply provides power for external I/O use.
Ground Fault Circuit Interrupter (GFCI)
The GFCI is wired in series from the AC power input to the servo amplifier. It monitors both AC
power leads to the servo amplifier, ensuring that current flowing in one lead is the same as the current
flowing out the other lead. If, due to a ground fault, the GFCI detects a net difference in the AC power
exceeding 30 milliamps (30mA or.030 Amps), it shuts off the AC power to the servo amplifier
automatically.
Test
Switch in
ON position
Figure 2-9.
Ground Fault Circuit Interrupter
Page 2-12
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Identifying the Components
Disconnect Switch
The disconnect switch is mechanically interlocked with the rotary actuator to prevent the enclosure
door from opening if the disconnect switch is in the ON position. Refer to Front Panel earlier in this
chapter for details about the rotary actuator.
Circuit Breaker/Fuses
The circuit breaker/Fuses protects the controller circuitry during an overload condition.
____________________________________________________________________________________________
December 2005
Page 2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
(This page is left blank intentionally.)
Page 2-14
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Installing the CS7000 Controller
3. Installing the CS7000 Controller
This chapter shows you how to mount the CS7000 Controller, discusses the basic issues involved in
placing the CS7000 Controller in your facility and shows you how to wire it.
Mounting the CS7000 Controller
The CS7000 Controller is installed vertically with the back flat against the mounting surface. Allow
sufficient space around the controller to attach the power cord, tool cable, I/O cable and printer cable.
Also be sure to allow space to open the door on the enclosure.
CAUTION!
Mount the CS7000 Controller away from moving machinery
and lift trucks on a structure that does not vibrate. Do not
mount the CS7000 Controller near large electrical systems,
motors, welding equipment, or in an area of temperature or
moisture extremes.
i
Figure 3-1 shows the dimensions of the CS7000 Controller (in inches).
December 2005
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Figure 3-1.
CS7000 Controller Dimensions of the Front and Bottom Panel
To mount the controller use four 1/4-20-in bolts or screws.
Emissions and Susceptibility
The CS7000 Controller meets the EC directives IEC 61000-6-2 (1999) and IEC 61000-6-4 (1997). It
does not radiate excessive electromagnetic or noise radiation, or interfere with other controllers and/or
electronic devices in its vicinity.
Page 3-2
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Installing the CS7000 Controller
Meeting the AC Input Power Requirements
For proper operation, the controller must be connected to a stable power source. The supply source
should be capable of delivering at least 1.5 kVA per channel at 220V for 177 Series tools. For the 277
Series tools, at least 2KVA per channel is recommended.
The voltage tolerance for 220V controllers is 208 to 250 VAC.
NOTE:
The maximum no-load speed of a nutrunner is based on a
nominal AC input voltage of 220V depending on the type of
controller; if the actual input voltage is lower, the maximum no
load speed of the nutrunner will be lower than specified.
?
CAUTION!
Failure to provide the proper power source can cause the
following problems in your CS7000 Fastening System:
i
•
•
•
The nutrunner might shut down before it reaches the
target torque during a rundown cycle.
The nutrunner might not operate when a cycle-on
signal is applied to the system.
The maximum free speed of the nutrunner might be
lower than specified.
Input Power Protection
A circuit breaker or fuses positioned between the AC input and the servo amplifier provides the
controller with short circuit protection.
____________________________________________________________________________________________
December 2005
Page 3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Grounding
WARNING! The GFCI cannot protect you against any potential
difference that exists between the nutrunner body and any
other metal fixturing or machinery. You must observe the
grounding requirements below as a safety protection.
Failure to follow this safety guideline can result in serious
personal injury.
!
It is extremely important that you connect the CS7000 Controller enclosure properly to an earth
ground. The CS7000 Controller has a ground prong on the power cord, (if supplied) but the AC outlet
that will be used must be grounded properly, as well.
Also make sure that all other machinery, such as conveyors, which will transport or hold parts that
will come in physical contact with the nutrunner, are properly grounded.
I/O Wiring
The CS7000 Controller is equipped with a 19-pin I/O connector for field I/O. The settings described
in Table 3-1 are VS default settings. The CS7000 Controller is capable of 12 discrete inputs and 12
discrete outputs, however, the standard 19-pin I/O connector does not accommodate I/O 9 through 12.
These extended I/O must be wired to the backplane directly if they are required. DCMII revision 3.00
or higher also supports 128 parameter sets and 16 sequences.
NOTE:
The 14-shell, 19-pin strain relief mating connector for the I/O
connector is part number 23-10-5200 [PT06A-14-19P (SR)].
?
Table 3-1. 19-Position Remote I/O Connector Pinout Signal Names and Descriptions
Pin
A
Signal
Description
Cycle On/Cycle On Enable
Clear Outputs
(Black wire - internal)
(Black wire - external)
This is a dual-purpose input.
When Set Defaults is clicked, VS sets this input to Start, this input
functions as a cycle on input. This means a fastening cycle can be
started by either pressing the throttle/trigger switch on the nutrunner OR
by activating this input.
When remote mode for the spindle is set to enable, this input functions as
a cycle on enable input. This means a fastening cycle can be started only
by pressing both the throttle/trigger switch on the nutrunner and activating
this input.
In addition, it is also set to Clear Outputs.
This is a level-sensitive input. For the fastening cycle to proceed, this
input must remain active. If this input becomes inactive at any time during
the fastening cycle, the cycle will be aborted and the nutrunner will stop
running.
Page 3-4
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Installing the CS7000 Controller
Table 3-1. 19-Position Remote I/O Connector Pinout Signal Names and
Descriptions (Continued)
Pin
B
Signal
Description
Forward/Reverse input
(White wire internal)
(White wire - external)
When Set Defaults is clicked, VS sets this input to the direction the
nutrunner turns in a fastening cycle:
If this input is active when a fastening cycle is started, the nutrunner will
run in the forward (fastening or tightening) direction. If this input is
inactive when a fastening cycle is started, the nutrunner will run in the
reverse (un-fastening or loosening) direction.
After a fastening cycle has started, changing the state of this input has no
effect on the fastening direction until the cycle on command (from either
the nutrunner or the cycle on input or both) is de-activated. This means
the input must be in the desired state BEFORE activation of the cycle
start input.
C
D
E
F
Discrete Input #7
(Gray wire - internal)
(Red wire - external)
Defaults to “Manual Calibration.”
Discrete Input #8
(Yellow wire - internal)
(Green wire - external)
Multi-purpose switch input “OR” function with switch on tool.
Limit Set Select B0 input
(Red wire - internal)
(Orange wire - external)
When Set Defaults is clicked, VS sets these three inputs to select which
of the eight internal limit (or parameter) sets are used for a fastening
cycle, as follows:
Limit Set Select B1 input
(Green wire - internal)
(Blue wire - external)
Limit Set
B2 Input
inactive
inactive
inactive
inactive
active
active
active
active
B1 Input
inactive
inactive
active
B0 Input
inactive
active
inactive
active
inactive
active
inactive
active
1
2
3
4
5
6
7
8
active
inactive
inactive
active
active
G
H
Limit Set Select B2 input
(Orange wire - internal)
(White/Black wire - external))
After a fastening cycle has started, changing the state of these inputs
does not change which limit set the CS7000 Controller uses until the
cycle on command (from either the nutrunner or the cycle on input or
both) is de-activated. This means these inputs must be in the desired
state BEFORE activation of the cycle start input.
+24 VDC
(Blue wire - internal
(Red/Black wire - external))
This pin (and pin T) is connected to the positive (+) terminal of the
internal 24VDC I/O power supply and is normally used as the common
connection for the input signals.
J
K
L
Discrete output #1*
(White/Black wire - internal)
(Green/Black wire - external)
Pins J, K, L, M, N, P, and U are the programmable discrete outputs.
Any one of these outputs will become active when its programmed
Discrete output #2*
(White/Red wire - internal)
(Red/Black wire - external)
Output function becomes true. When Set Defaults is clicked, VS sets
these outputs to:
Discrete output #3*
(White/Green wire - internal)
(Blue/Black wire -external)
____________________________________________________________________________________________
December 2005 Page 3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Table 3-1. 19-Position Remote I/O Connector Pinout Signal Names and
Descriptions (Continued)
Pin
M
Signal
Description
Discrete output #4*
J = Cycle Finish, K = Cycle Good, L = Cycle Bad, N = In Cycle.
(White/Violet wire - internal)
(Black/White wire - external))
N
P
Discrete output #5*
(White/Blue wire - internal)
(Red/White wire - external)
Discrete output #6
(White/Gray wire - internal)
(Green/White wire - external)
R
Synchronization in/out
(White/Orange wire - internal)
(Orange/Red wire - external)
This bi-directional signal is used for synchronizing two or more spindles in
a multi-spindle fastening application. It is connected to both the
synchronization output (Discrete output #8) and the synchronization input
(Discrete input #6).
If Sync is set to On, the synchronization output becomes active when a
fastening cycle is started. When the nutrunner output torque reaches the
Control Reference level, the synchronization output is de-activated. At the
same time, the state of the synchronization input is sampled. If it is still
active because some other spindle has not reached the synchronization
level yet, it stops the nutrunner and waits for the synchronization input to
become inactive. Afterwards, it re-starts the nutrunner and finishes the
fastening cycle.
This pin should be connected to the synchronization in/out pin of all other
spindles for which synchronization is desired.
NOTE:
This feature only functions when JP8 and JP9 are set to
defaults.
?
S
T
Output common
(White/Brown wire - internal)
(Blue/white wire - external)
This feature only functions when JP8 and JP9 are set to defaults.
+24 VDC
(Blue wire - internal)
(Black/Red wire - external)
This pin (and pin H) is connected to the positive (+) terminal of the
internal 24VDC I/O power supply and is normally used as the common
connection for the input signals.
U
Discrete output #7*
(Brown wire - internal)
(White/Red wire - external)
Pins U and J, K, L, M, N, and P are the programmable discrete outputs.
Any one of these outputs will become active when its programmed output
function becomes true. The functions of these outputs are set with VS set
output.
V
Synchronization common
(Violet wire - internal)
(Blue/Red wire - external)
This is the common connection for the synchronization input/output. It
should be connected to the synchronization common pin of all other
spindles for which synchronization is desired.
NOTE:
Active means an input is connected to +24VDC. Inactive
means an input is either not wired or is wired to common.
?
Page 3-6
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Installing the CS7000 Controller
A remote input circuit schematic is shown in Figure 3-2.
Figure 3-2. Remote Input Circuit Schematics
To ensure that you operate the fastening system properly, refer to Table 3-2 for input requirements.
Table 3-2. Guidelines for Proper Operation of the Controller I/O Signals
Discrete Inputs
Highest permissible input voltage
Lowest permissible input voltage
Minimum guaranteed input activation
Maximum guaranteed input deactivation
Discrete outputs
Unit
30 V
-5 V
10 V
1.5 V
Unit
Maximum output current
360 mA
Maximum voltage
28 Volts DC
NOTE:
Installing J8 (supplied 24 VDC to “output-common-bus” and
each of the individual output (J12 and J13 jumpers) eliminates
the need to wire 24VDC to the output terminals for sourcing.
?
____________________________________________________________________________________________
December 2005 Page 3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Connector Pinout Definitions
Pinout definitions are provided for the tool, I/O, TCM network, RS-232 and printer connectors.
Tool Connector “26 pin” (Metal SMC) – Front View
Pin Designation
Wire Color (Ref)
RED
Function
POWER PHASE 2
+ 24 VOLTS
COMMON
CLK -
1
5
ORN/WHT
WHT/ORN
WHT/BR
BR/WHT
BLU/WHT
WHT/GRN
GRN/WHT
GRN
6
12
13
CLK +
14
TXD +
15
RXD -
16
RXD +
19
POWER SHIELD
POWER PHASE 1
POWER PHASE 3
RESOLVER SHIELD
SIG SHIELD
TOOL FRAME GRD
TXD -
20
WHT
21
BLK
22
GRN
23
GRN
25
GRN-YEL
WHT/BLU
--
26
Nos. not listed
No connection
RESOLVER R1
R2
10
11
8
WHT/RED
WHT/BLK
WHT
S1
24
9
WHT/GRN
GRN
S2
S3
7
WHT/YEL
S4
Page 3-8
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Installing the CS7000 Controller
I/O Connector – Front View
Pin Designation
Wire Color (Ref)
Function
A
B
C
D
E
F
BLK
WHT
GRY
CYCLE ON INPUT
FORWARD/REVERSE INPUT
DISCRETE INPUT #7
YEL
DISCRETE INPUT #8
RED
LIMIT SET SELECT B0 INPUT
LIMIT SET SELECT B1 INPUT
LIMIT SET SELECT B2 INPUT
+24V INPUT
GRN
G
H
J
ORN
BLU
WHT/BLK
DISCRETE OUTPUT #1
(FINISHED)
K
L
WHT/RED
WHT/GRN
WHT/YEL
WHT/BLU
WHT/GRY
WHT/GRN
WHT/BRN
BU
DISCRETE OUTPUT #2 (ACCEPT)
DISCRETE OUTPUT #3 (REJECT)
DISCRETE OUTPUT #4
DISCRETE OUTPUT #5
DISCRETE OUTPUT #6
SYNC IN/OUT
M
N
P
R
S
T
OUTPUT COMMON
+24V
U
V
BRN
DISCRETE OUTPUT #7
SYNC COMMON
VIO
TCM (IN and OUT) Network Connectors – Front View
Pin Designation
Wire Color (Ref)
BRN/WHT
WHT/BRN
ORN/WHT
WHT/ORN
GRN/WHT
WHT/GRN
BLU/WHT
GRN
Function
TXD+ OUT
TXD- OUT
RXD+ IN
A
B
C
D
E
F
RXD- OUT
CLK+ OUT
CLK- OUT
G
H
SHIELD COMMON
SHIELD
RS-232 Connector – Front View
Pin Designation
Wire Color (Ref)
Function
RXD
2
3
5
7
8
BLU
GRN
BLK
RED
YEL
TXD
GND
RTS
CTS
____________________________________________________________________________________________
December 2005 Page 3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Printer/Computer/Diagnostics (RS-232) Connector – Front View
Pin Designation
Wire Color (Ref)
Function
RXD
2
3
5
7
8
BLU
GRN
BLK
RED
YEL
TXD
GND
RTS
CTS
Programming the CS7000 Controller (In General)
After you have mounted the controller and become familiar with its basic components, you must
program it with the required fastening strategy and parameter set limits before you can begin fastening
operations. Refer to the Visual Supervisor User s Guide (part number 39-30-34823) for connection
and setup information.
Programming the CS7000 with Ethernet (CCM)
Adding a CCM board to the CS7000 provides ethernet capability and other future functions. The
Initial release supports Visual Supervisor, and subsequent releases will provide interfaces to many
Customer specific networks. Also future capabilities will include Fieldbus and Keypad/displays. A
Null-modem cable that provides an RS-232 connection (Typically 9 pin-d female on both ends) will
be required for setup of the CCM module. This cable will plug into the CS7000
communications/diagnostics port. If using Hyper-terminal, use 9600 baud, 8 data, no parity and one
stop bit. Hit the <Enter key> and a > should appear. Hitting ? will show a list of available
commands.
To configure the CS7000 Controller to link to Visual Supervisor, you must use the ipconfig
command to establish the TCP/IP parameters (IP address etc.). At the Visual-Supervisor-Host, you
must set up VsSystemSettings to use Ethernet and enter the IP address of this controller. Once that is
saved, VS should start up and communicate normally with the controller. If problems occur,
PING ommands and LED s on the CCM that should help guide the user to the problem. It is
necessary to issue a commit command to permanently save settings.
Page 3-10
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Technical Information
4. Technical Information
Maintenance of the CS7000 Controller consists of replacing fuses and cleaning the enclosure window.
Replacement Parts
If, at any time, you need to replace or order new parts for your CS7000 Controller.
Table 4-1.
Replacement Parts
Qty.
Description
Part Number
49-4102-015000
12-20-5007
1
1
1
2
50A TCM GEN2
+24V DC Power Supply
Fuse 1A SB, Littelfuse 39001 5x20 mm
Fuse 20A, MDA-20
13-10-61001
13-10-0555
NOTE:
All part numbers used in Table 4-1 are CP techmotive part
numbers unless otherwise specified.
?
Cleaning the Enclosure Window
Use only water-based cleaners to clean the plastic window. Other solvents may damage the window.
Assembly Drawings
Assembly and wiring diagrams are available for the CS7000 Controller. To request an assembly or
wiring diagram, contact the CP techmotive Technical Service Department. To contact CP techmotive,
refer to Contact Information next.
December 2005
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
Contact Information
NOTE:
You will need to prefix American telephone numbers with the
International Access Code for the U.S. when calling from
another country.
?
If you require additional technical information about the CS7000 Controller, call
1-877-224-7377 from inside the U.S. or Canada, or (001) 248-596-0600 from outside the U.S. or
Alternatively, you can also contact CP techmotive at:
42860, Nine Mile Road,
Novi, MI 48375-4122
Page 4-2
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Index
5. Index
A
F
AC
front panel, 2-1
fuse, 1-3, 4-1
input, 3-3
Input Receptacle, 2-5
address switches, 2-6
pullers, 1-3
substitutes, 1-3
B
G
backplane, 2-11
battery, 2-9
bottom panel, 2-1
ground fault circuit interrupter, 2-6, 2-12
I
I/O
C
cable, 3-1
connector, 2-6, 3-9
Port, 2-6
circuit breaker, 2-6, 2-13
Clear Outputs, 3-4
connector
power, 2-6
input
active, 3-6
inactive, 3-6
Input AC Receptacle, 2-5
I/O, 2-6, 3-9
printer, 2-5, 3-10
RS-232, 2-5, 3-9
SDLC/485, 2-5, 3-9
tool, 2-5, 3-8
Cycle
Bad, 3-6
Finish, 3-6
L
latch, 2-3
LED, 2-9
LED display, 2-3
Good, 3-6
D
Device Control Module
battery, 2-9
M
Manual Calibration, 3-5
multi purpose switch, 3-5
disconnect switch, 1-3, 2-3, 2-6, 2-13
dual-purpose input, 3-4
N
E
nutrunner, 3-4, 3-5
electrical
drawings, 1-3
fires, 1-3
hazards, 1-3
O
output current, 3-7
wiring, 1-3
P
enclosure
Panels
components, 2-7
interior, 2-1
window, 4-1
Bottom, 2-4
Top, 2-4
Panels
extinguishers, 1-3
Front, 2-2
Parameter Set Switch, 2-3
parameter sets, 3-5
PFCS, 2-12
December 2005
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6159939130 CS7000 Controller Hardware Overview Manual
pinout, 3-8
safety,
Plant Floor Communication System, 2-12
potentiometer, 2-9
power supply, 2-6, 2-12, 3-5, 4-1
printer cable, 3-1
electrical, 1-1, 1-3
SDLC/485 I/O network connector, 2-5, 3-9
servo amplifier, 2-6, 2-9, 2-12
spindle, 2-8
printer connector, 2-5, 3-10
programmable discrete output, 3-6
synchronization input/output, 3-6
synchronization output, 3-6
R
T
remote input circuit schematic, 3-7
tool cable, 3-1
Tool Connector, 2-5, 3-8
Tool Control Module, 2-8
top panel, 2-1
repairs, 1-3
rotary actuator, 2-3
RS-232
connector, 2-5, 3-9
port, 2-5
V
voltage, 1-3, 3-7
S
safety glasses, 1-3
Index-5-2
39-30-41365
Download from Www.Somanuals.com. All Manuals Search And Download.
(This page left blank intentionally)
Download from Www.Somanuals.com. All Manuals Search And Download.
Please find your local contact at: www.cp.com
U.S. English
Printed in USA
Copyright 2005
CP techmotive, Novi, MI, USA
Download from Www.Somanuals.com. All Manuals Search And Download.
|