Telescoping pole saw
Model 96405
seT up and operaTing insTrucTions
Diagrams within this manual are not drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe This Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
saVe This Manual
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
iMporTanT saFeTY inForMaTion
in this manual, on the labeling, and all other information
provided with this product:
This is the safety alert symbol. it is used to alert you to potential
personal injury hazards. obey all safety messages that follow this
symbol to avoid possible injury or death.
danger indicates a hazardous situation
which, if not avoided, will result in death or
serious injury.
warning indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
cauTion, used with the safety alert
symbol, indicates a hazardous situation
which, if not avoided, could result in minor
or moderate injury.
noTice is used to address practices not
related to personal injury.
cauTion, without the safety alert symbol,
is used to address practices not related to
personal injury.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
general saFeTY rules
warning! read all instructions
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury. The term “power tool” in all of the warnings listed
below refers to your mains-operated (corded) power tool.
SAVE THESE INSTRUCTIONS
1.
work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2.
electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d. do not abuse the cord. never use the cord for carrying, pulling or
unplugging the power tool. keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
3.
personal safety
a. Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. use safety equipment. always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, heavy-duty work gloves,
hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Avoid accidental starting. Ensure the switch is in the “OFF” position before
plugging in. Carrying power tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or long
hair can be caught in moving parts.
4.
power tool use and care
a. Always plug this tool into a GFCI equipped 120V electrical outlet.
b. Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it
was designed.
c. Do not use the power tool if the switch does not turn it on and off. Do not use
if the Safety Switch does not operate properly. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
d. disconnect the plug from the power source and/or the battery pack from
the power tool before making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
e. store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained
users.
f. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
g. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
h. Use the power tool in accordance with these instructions and in the manner
intended for the particular type of power tool, taking into account the working
conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
service
a. Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
speciFic saFeTY rules
1.
2.
3.
4.
Only use the Pole Saw to cut wood. Never attempt to cut masonry, metal or any
other material with the Pole Saw.
Clear the work area before beginning a cutting project, and plan a path of retreat
to avoid falling branches.
Only use this tool while standing on a firm, level surface. Do not use this tool
while mounted on a ladder or standing on any unstable platform.
Do not stand directly underneath the branch being cut. Always cut at no more
than a 60° angle to the branch and extend the telescopic arm of the Pole Saw for
best possible clearance.
5.
6.
Be mindful of where the branch will fall. Do not use within 50’ of overhead power
lines or above anything that could be damaged by falling branches.
Use extreme caution when cutting branches. Branches under tension could
spring back and cause severe injury. Slender branches can catch in the chain
and whip back towards the operator.
7.
ꢀ.
Do not address the tip of the Pole Saw to the material being cut, as it can kick
back violently causing severe injury.
Maintain labels and nameplates on the tool. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
9.
Avoid unintentional starting. Prepare to begin work before turning on the tool.
10.
Do not lay the tool down until it has come to a complete stop. Moving parts can
grab the surface and pull the tool out of your control.
11.
12.
When using the Pole Saw, maintain a firm grip on the tool with both hands to
resist torque when cutting.
Do not leave the tool unattended when it is plugged into an electrical outlet. Turn
off the tool, and unplug it from its electrical outlet before leaving.
13.
14.
This product is not a toy. Keep it out of reach of children.
danger! People with pacemakers should not use chain saws. Chain saws
produce strong electromagnetic fields that can cause pacemaker interference or
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
pacemaker failure. People with pacemakers should consult their physician(s) for
advice.
15.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contains chemicals known [to the State of California] to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
Lead from lead-based paints
Crystalline silica from bricks and cement or other masonry products
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that
are specially designed to filter out microscopic particles. (California Health &
Safety Code § 25249.5, et seq.)
kickback precautions
16. Kickback is a dangerous reaction that can lead to serious injury. Kickback may
occur when the moving Chain contacts an object at the upper portion of the tip of
the Guide Bar or when the wood closes in and pinches the Saw Chain in the cut.
Contact at the upper portion of the tip of the Guide Bar can cause the Chain to
dig into the wood and stop the Chain for an instant. The result is a quick, reverse
reaction which kicks the Guide Bar up and back toward the operator. If the Chain
is pinched along the top of the Guide Bar, the Guide Bar can be driven rapidly
back toward the operator. Either of these reactions can cause loss of Pole
Saw control which can result in serious injury. Do not rely only upon the safety
devices built into the Pole Saw. As an operator, you should take several steps to
keep the cutting job free from accident or injury:
• Make sure the area in which you are cutting is free from obstructions. Do not
allow the nose of the Guide Bar to contact a log, branch, fence, or any other
obstruction while you are operating the tool.
• Always cut with the Engine running at full speed. Fully squeeze the Throttle and
maintain a steady cutting speed.
• Always keep the Chain clean and sharp.
• Keep all guards and safety devices in proper working order and properly
adjusted.
• Never use the Pole Saw on a ladder or unstable support.
• Before starting the Engine, make sure the Chain is not contacting any object.
• Shut off the Engine, and make sure the Chain has stopped before setting the
tool down.
17.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
saVe These insTrucTions.
grounding
improperly connecting the grounding wire can result in
electric shock.
Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. do not modify
the power cord plug provided with the tool. never remove
the grounding prong from the plug. do not use the tool if
the power cord or plug is damaged. if damaged, have it
repaired by a service facility before use. if the plug will not
fit the outlet, have a proper outlet installed by a qualified
electrician.
grounded Tools: Tools with Three prong plugs
1.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of electric
shock. (see 3-prong plug and outlet.)
2.
3.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (see 3-prong plug and outlet.)
The tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration.
(see 3-prong plug and outlet.)
3-prong plug and outlet
outlets for 2-prong plug
SKU 96405
For technical questions, please call 1-800-444-3353.
Page ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
double insulated Tools: Tools with Two prong plugs
1.
2.
Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies
with the applicable standards of Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical Code.
(see outlets for 2-prong plug.)
Double insulated tools may be used in either of the 120 volt outlets shown in the
preceding illustration. (see outlets for 2-prong plug.)
extension cords
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(see Table a.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(see Table a.)
4.
5.
When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required. (see Table a.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(see Table a.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure the extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
ꢀ.
Protect the extension cords from sharp objects, excessive heat, and damp or wet
areas.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
recoMMended MiniMuM wire gauge For eXTension cords* (120/240 VolT)
naMeplaTe
eXTension cord lengTh
aMperes
(at full load)
25 Feet
50 Feet
75 Feet
100 Feet
150 Feet
0 – 2.0
2.1 – 3.4
1ꢀ
1ꢀ
1ꢀ
1ꢀ
1ꢀ
14
12
1ꢀ
1ꢀ
1ꢀ
16
14
12
10
1ꢀ
1ꢀ
16
14
12
10
-
1ꢀ
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
Table a
-
-
-
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
symbology
Double Insulated
Volts Alternating Current
Amperes
V~
a
Canadian Standards Association
No Load Revolutions per Minute
(RPM)
Underwriters Laboratories, Inc.
n xxxx/min.
0
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
speciFicaTions
Electrical Requirements
120 V~ / 60 Hz
Motor No Load Amperage
Blade
3.5<->4.0 AMPS
ꢀ” (Cutting Capacity = 6.7”)
3149 Feet Per Minute
Chain Speed
Pitch: 3/ꢀ”
Chain Specs
Gauge” 0.043”
Center Links 33
Oil Capacity
5.07 Ounces
Cord Information
17-5/ꢀ” L 1ꢀ-AWG X 2C
Built in Oiler
Pole Extends from 29” to 6’2”
Polarized Plug
Features
Safety Trigger
®
Oregon Chain
unpacking
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
seT up insTrucTions
read the enTire iMporTanT saFeTY inForMaTion section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
risk of accidental starting; resulting in serious personal
injury. Turn the power switch of the tool to its “oFF”
position and unplug the tool from its electrical outlet before
assembling or making any adjustments to the tool.
note: For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
assembly
oil requirements.
1.
The Chain of the Pole Saw requires oil to function. The Oil Tank of the Pole Saw
must be kept full when in use, and drained before storage. Lubricate the Chain
with a high-quality chain saw oil before each use.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
Always turn the Power Switch of the Pole Saw to the “OFF” position, unplug it
from the outlet, and allow it to cool down completely before adding oil.
To fill the Oil Tank (42), remove the Oil Cap (41) and add up to 5 Ounces of high-
quality chain saw oil. Replace Oil Cap when full.
attaching the chain.
pole saw shown with plastic cover (34) removed.
guide bar (36)
chain (35)
chain Tension
screw (40)
drive sprocket
(31)
1.
2.
3.
Remove the Plastic Cover (34) and align the Chain (35) along the groove in the
Guide Bar (36) and over the Drive Sprocket (31). The directional arrows on the
Chain must correspond with the directional arrows on the Guide Bar or the Pole
Saw will not function.
Adjust the Chain Tension Screw (40) until the Chain is secure. The Chain should
not be adjusted too tightly, since it does have to be able to move. When properly
adjusted, the Chain should be able to be pulled, using light force, about 1/4”
away from the Guide Bar and snap back without sagging.
Replace the Plastic Cover before use.
assembling the Telescopic pole.
1.
2.
Connect Aluminum Tube 1 (45) and Aluminum Tube 2 (52) with Connector 1
(46). Secure Plastic Coupling 1A (4ꢀ) and Plastic Coupling 2A (51) with Screws
(43), and Nuts (ꢀ, 47). Fasten with Locking Knob (50)
Connect Aluminum Tube 2 (52) and Aluminum Tube 3 (57) with Connector 2
(53). Secure Plastic Coupling 1B (55) and Plastic Coupling 2B (56) with Screws
(43), and Nuts (ꢀ, 47). Fasten with Locking Knob (50).
Functions
The Telescoping Pole Saw is designed to trim branches on trees.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
operaTing insTrucTions
read the enTire iMporTanT saFeTY inForMaTion section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
general operating instructions
1.
2.
Turn the Power Switch of the tool to the “OFF” position and unplug the tool from
the electrical outlet before assembling or making any adjustments to the tool.
Maintain a proper grip on the Pole Saw whenever it is running. Hold the tool with
both hands. Always keep your left hand on the Front Handle (61) and your right
hand on the Rear Handle (74, ꢀ6), so that your body is to the left of the Pole Saw.
Never use a left-handed (cross-handed) grip or any stance which would place
your body or arm across the chain line.
3.
4.
5.
Always wear the Shoulder Strap (66) to properly support the Pole Saw when
moving or using unit.
To activate the Saw, push the Safety Switch (72) forward and depress the Power
Switch (75).
safety switch (72)
Allow the Saw Chain to cut for you.
Exert only light downward pressure. If
power
switch
you attempt to force the cut, damage
to the Guard Bar, Chain, or Motor can
result.
(75)
6.
7.
Do not use a back and forth sawing
type motion for cutting.
power
cord
(88)
Release the Power Switch as soon
as the cut is completed. Running
the Pole Saw for long periods without a pause can cause unnecessary wear or
damage to the Guard Bar, Chain, and Motor.
beware kickback! Never cut with tip of blade.
ꢀ.
Cut longer branches down in sections for greater efficiency and safety.
(See example below.)
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
IMPORTANT: After running the Pole Saw for an extended period of time, allow
the Engine to idle for several minutes to dissipate heat. This will prevent the Pole
Saw from being damaged by overheating.
10.
To prevent accidents, turn off the tool and disconnect from the power supply after
use. Clean the Pole Saw, then store the tool indoors out of children’s reach.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
MainTenance and serVicing
risk of serious personal injury from accidental starting
or electric shock. Turn the power switch of the tool to its
“oFF” position and unplug the tool from its electrical outlet
before performing any inspection, maintenance, or cleaning
procedures.
damaged equipment can fail, causing serious personal
injury. do not use damaged equipment. if abnormal noise or
vibration occurs, have the problem corrected before further
use.
cleaning, maintenance, and lubrication
1.
beFore each use, inspect the general condition of the tool. Check for
loose screws, misalignment or binding of moving parts, cracked or broken
parts, damaged electrical wiring, and any other condition that may affect its safe
operation.
2.
3.
aFTer use, clean external surfaces of the tool with clean, moist cloth.
After each use, remove the Plastic Cover (34) and clean oil and sawdust out of
the area underneath, especially the recess of
the Chain Tension Screw (40) and oil duct,
with a damp cloth or compressed air to extend
the life of the Pole Saw.
oil duct
4.
5.
warning! if the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
chain Tension
screw (40)
Any repairs not specifically covered in this
manual MUST be completed by a qualified
service professional.
Troubleshooting
problem
Pole Saw will not start
possible causes
1. No power at outlet.
probable solutions
1. Check power at outlet.
2. Cord not connected.
2. Check that cord is plugged in.
Pole Saw runs, but will
not cut
1. Chain is placed backwards on
Guide Bar
1. Remove Chain and reattach
correctly
Pole Saw only cuts when 1. Chain is dull.
forced. Cutting yields only
sawdust and large chips
1. Have Chain sharpened by
a professional sharpening
service.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
problem
possible causes
probable solutions
Pole Saw runs slowly and 1. Power supply receiving low
1. Extension cord wire size is too
stalls easily
voltage.
small.
Pole Saw does not run
when Power Switch is
depressed.
1. Safety Switch not depressed
enough to release Power Switch.
1. Press Safety Lock in before
squeezing Power Switch.
2. Extension cord connections are
loose.
2. Cord cord connections.
3. Check line fuse and circuit
breaker.
3. Open line fuse or circuit breaker
fault.
4. Have the Pole Saw serviced
4. Open wiring circuit on saw.
1. Chain tension too tight.
2. Gear Train Failure.
by a qualified mechanic.
Motor of Pole Saw runs,
but Chain does not move.
1. Adjust Chain Tension Screw to
lower tension on Chain.
2. Have the Pole Saw serviced
by a qualified mechanic.
Chain is not receiving
enough oil.
1. Clogged oil slot in guide bar.
2. Oil is too thick.
1. Remove Guide Bar and clean
oil slot.
2. Use lighter weight oil.
1. Tighten Chain.
Chain comes off Guide
Bar.
1. Chain is too loose.
2. Guide Bar and Chain are not
assembled correctly.
2. Review unit assembly.
Saw smokes.
Saw leaks oil.
1. Pole Saw is damaged. Do not
use the Pole Saw.
1. Have the Pole Saw serviced
by a qualified mechanic.
1. Oil Cover is not secure.
1. Tighten Oil Cover.
Guard Bar and Chain
running hot and smoking.
1. Chain tension too tight.
2. Oil Tank empty.
1. Adjust Chain Tension Screw to
lower tension on Chain.
2. Refill Oil Tank.
please read The Following careFullY
The ManuFacTurer and/or disTribuTor has proVided The parTs lisT and asseMblY
diagraM in This Manual as a reFerence Tool onlY. neiTher The ManuFacTurer or
disTribuTor Makes anY represenTaTion or warranTY oF anY kind To The buYer ThaT
he or she is qualiFied To Make anY repairs To The producT, or ThaT he or she is
qualiFied To replace anY parTs oF The producT. in FacT, The ManuFacTurer and/or
disTribuTor eXpresslY sTaTes ThaT all repairs and parTs replaceMenTs should
be underTaken bY cerTiFied and licensed Technicians, and noT bY The buYer. The
buYer assuMes all risk and liabiliTY arising ouT oF his or her repairs To The
original producT or replaceMenT parTs ThereTo, or arising ouT oF his or her
insTallaTion oF replaceMenT parTs ThereTo.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
parTs lisT
part
1
description
Screw ST 4x1ꢀ
part
description
Drive Sprocket
part
60
61
62
63
64
65
66
67
6ꢀ
69
70
71
72
73
74
75
76
77
7ꢀ
79
ꢀ0
ꢀ1
ꢀ2
ꢀ3
ꢀ4
ꢀ5
ꢀ6
ꢀ7
ꢀꢀ
description
Washer 16x6x1.5
Front Handle
Screw
31
32
33
34
35
36
37
3ꢀ
39
40
41
42
43
44
45
46
47
4ꢀ
49
50
51
52
53
54
55
56
57
5ꢀ
59
2
Plastic End Cap
Screw M5x5ꢀ
Spring Washer
Washer ꢀx4.2x0.6
Carbon Brush Housing
Carbon Brush
Nut M4
C-ring
3
Nut Mꢀ
4
Plastic Cover
Chain
Retaining Screw
D-ring
5
6
Guide Bar
Screw M3x5
7
Dowel Pin Mꢀ
Plastic Slider
Oil Seal
Shoulder Strap
Wing Nut
ꢀ
9
Motor Housing
Stator
Screw M5x20
Nut M5
10
11
12
13
14
15
16
17
1ꢀ
19
20
21
22
23
24
25
26
27
2ꢀ
29
30
Chain Tension Screw
Oil Cap
Plastic Plate
Plastic Bracket
Spring
Rotor Assembly
Screw M4x65
Key
Oil Tank
Screw M4x15
Mounting Piece
Aluminum Tube 1
Connector 1
Nut M6
Safety Switch
Switch Assembly
Rear Handle Part A
Power Switch
Spring
Gear Box Housing
Gleason Gear
Strain Relief
Strain Relief 2
Ball Bearing
Plastic Coupling 1A
Plastic Slider 1
Locking Knob
Plastic Coupling 2A
Aluminum Tube 2
Connector 2
Plastic Slider 2
Plastic Coupling 1B
Plastic Coupling 2B
Aluminum Tube 3
Soft Handle
Spring Housing Cover
Bushing 1
Output Gleason Gear
Output Shaft
Key 3xꢀ
Screw ST 4x10
Plastic Spool Cover
Spool Assembly
Spool Shaft Assembly
Capacitor
Oil Pump Pin with Gear
Oil Pump Housing
Ball Bearing
Terminal Box
Spiral Spring
Rear Handle Part B
Cable Protection
Power Cord
Adjustment Screw
Main Housing
Bushing
Felt Seal
Plastic Knob for Front
Handle
Washer
record product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
asseMblY diagraM
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
liMiTed 90 daY warranTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection verifies the defect, we
will either repair or replace the product at our election or we may elect to refund the
purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that
the defect resulted from causes not within the scope of our warranty, then you must
bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 96405
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
|