20” HigH velocity Air
circulAtor
66878
Set up And operAting inStructionS
®
distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
reAd And SAve tHeSe inStructionS.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
cAution, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
manual cannot cover all conditions
and situations that may occur. It must
be understood by operator that com-
mon sense and caution are factors
which cannot be built into this prod-
uct, but must be supplied by operator.
Additional Safety instructions
1. Maintain labels and nameplates on
the tool. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
2. Do not run Power Cord under car-
peting. Do not cover cord with throw
rugs, runners or similar coverings. Ar-
range cord away from traffic area and
where it will not be tripped over. Do
not let cord hang over edge of table
or counter, or touch hot surfaces. Do
not pull on cord.
3. Use only in dry environments. Do not
use in bathrooms, laundry area, near
sinks or other sources of water.
4. This product is not a toy. Keep it out
of reach of children.
5. WARNING: Handling cord on this
product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
6. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure.
7. The warnings, precautions, and in-
structions discussed in this instruction
rev 09f
SKU 66878
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SpeciFicAtionS
Electrical Requirements 120 V~ / 60 Hz / 1.6A
Low: 1225 RPM
Speeds (approx.)
Medium: 1360 RPM
High: 1480 RPM
HouSeHold uSe only
e144918
unpAcking
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon
as possible.
Save this Manual
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
ASSeMBly
read the entire ruleS For
SAFe operAtion section at
the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
SKU 66878
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
to prevent
SeriouS injury
4. Insert the ends of the Stand Base (3)
into the Stand Arms.
FroM AccidentAl
operAtion or electric
SHock:
Before assembly, cleaning or
adjustment, make sure the
switch is turned off, the cord
is unplugged, and the unit has
cooled.
5. Align the holes in the sides of the
Stand pieces and thread the Screws
in place.
6. Adjust the body of the fan to the de-
sired angle, then Tighten the Adjust-
ment Knobs.
note: For additional information regarding
parts listed, refer to Assembly dia-
gram at the back of the manual.
operAtion
read the entire ruleS For
SAFe operAtion section at
the beginning of this manual
including all text under
Fan Body (1)
Adjustment
Knob (4)
subheadings therein before set
up or use of this product.
1. Turn the knob on the back of the Fan
Body (1) to Off.
2. Set the Fan on a dry, stable surface.
Stand
Arm (2)
3. Plug the power cord into a standard
120V AC outlet.
4. Turn the Knob on the back of the fan
to the desired setting: Low, Medium
or High.
Screw (5)
5. Adjust the tilt of the Fan Body by
loosening the Adjustment Knobs (4),
changing the tilt of the body, then
tightening the Adjustment Knobs.
Stand Base (3)
Figure 1
1. Place the Fan Body (1) on a flat and
6. When done, turn the Knob on the
back of the Fan Body to Off and un-
plug.
stable surface.
2. Remove the Screws (5) and set
aside.
note: It is normal for the motor of the
Fan to feel warm to the touch dur-
ing operation. The motor is thermally
protected and will automatically shut
off when it overheats for any reason.
If this happens, immediately discon-
nect the Fan from the power outlet.
3. Slide the Adjustment Knobs (4) onto
the bolts on the Stand Arms (2) and
loosen the Stand Arms slightly by
turning the Adjustment Knobs counter
clockwise.
SKU 66878
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Allow to completely cool down before
turning on again.
inSpection And
MAintenAnce
The motor bearings are permanently
lubricated at the factory and do not
require any additional lubrication.
to prevent
SeriouS injury
FroM AccidentAl
operAtion or electric
SHock:
Before appliance inspection
or maintenance, make sure
the appliance’s switch is
turned off, the cord is
unplugged, and the unit has
cooled completely.
to prevent SeriouS
injury FroM AppliAnce
FAilure:
do not use damaged
appliances. if abnormal
noise or vibration occurs,
have the problem corrected
before further use.
1. BeFore eAcH uSe, inspect con-
dition of the Fan. Check for loose
screws, misalignment or binding of
moving parts, cracked or broken
parts, and any other condition that
may affect its safe operation.
2. Clean regularly to prevent dust from
accumulating on Blades and Grill. To
clean:
a. Unthread the screws along the outer
edge of the Grill (6) and remove the
front of the Grill.
b. Use a damp cloth with water and a
soft brush to clean the blades and
the Grill. Do not use harsh chemical
cleaners. Do not bend the blades.
3. DO NOT IMMERSE MOTOR.
4. Allow Fan to dry completely before
use.
SKU 66878
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
pleASe reAd tHe FolloWing cAreFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED
TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN By CERTIFIED AND LICENSED
TECHNICIANS, AND NOT By THE BUyER. THE BUyER ASSUMES ALL RISK AND LIABILITy ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
pArtS liSt And ASSeMBly diAgrAM
part
description
Qty
part
description
Qty
1
2
3
Fan Body
1
2
1
4
5
6
Adjustment Knob
Screw
Grill
2
2
1
Stand Arm
Stand Base
Grill (6)
Fan Body (1)
Adjustment
Knob (4)
Stand
Arm (2)
Screw (5)
Stand Base (3)
record product’s Serial number Here:
note:If product has no serial number, record month and year of purchase instead.
note:Some parts are listed and shown for illustration purposes only, and are not available individually as
replacement parts.
SKU 66878
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
liMited 90 dAy WArrAnty
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTy IS ExPRESS-
Ly IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 66878
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|