12V Lithium CordLess driLL
model 69360
set up and operating instruCtions
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this manuaL.
©
®
Copyright 2010 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1‑800‑444‑3353.
manual revised 12a
Download from Www.Somanuals.com. All Manuals Search And Download.
operating a power tool. do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result
in serious personal injury.
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breathing
protection must be NIOSH-approved for
the specific hazards in the work area.
4. power tool use and care
b. use personal protective equipment.
always wear eye protection. Safety
equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing
protection used for appropriate
a. do not force the power tool. use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate
for which it was designed.
conditions will reduce personal injuries.
b. do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must
be repaired.
c. prevent unintentional starting.
ensure the trigger is in the off‑
position before connecting to power
source and/or battery pack, picking
up or carrying the tool. Carrying
power tools with your finger on the
switch or energizing power tools that
have the switch on invites accidents.
c. disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories,
or storing power tools. Such
preventive safety measures reduce
the risk of starting the power tool
accidentally.
d. remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.
d. store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
e. do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool
in unexpected situations.
f. dress properly. do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry
or long hair can be caught in moving
parts.
e. maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. if damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
g. if devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
these devices can reduce dust-related
hazards.
f. Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
h. only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
g. use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of
the power tool for operations different
from those intended could result in a
hazardous situation.
drill and impact drill safety
Warnings
1. hold power tools by insulated
gripping surfaces when performing
an operation where the cutting tool
may contact hidden wiring or its own
cord. Contact with a ″live″ wire will make
exposed metal parts of the tool ″live″ and
shock the operator.
5. Battery tool use and care
a. recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire
when used with another battery pack.
2. Let bit cool before touching, changing
or adjusting it. Bits heat up dramatically
while in use, and can burn you.
3. If the drill bit jams, release the trigger
immediately; drill torque can cause injury
or break bit.
b. use power tools only with
specifically designated battery
packs. Use of any other battery packs
may create a risk of injury and fire.
4. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
c. When battery pack is not in use, keep
it away from other metal objects,
like paper clips, coins, keys, nails,
screws or other small metal objects,
that can make a connection from
one terminal to another. Shorting the
battery terminals together may cause
burns or a fire.
5. Avoid unintentional starting. Prepare to
begin work before turning on the tool.
6. Do not lay the tool down until it has come
to a complete stop. Moving parts can
grab the surface and pull the tool out of
your control.
d. under abusive conditions, liquid
may be ejected from the battery;
avoid contact. if contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
7. When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.
8. Do not leave the tool unattended when
it is plugged into an electrical outlet.
Turn off the tool, and unplug it from its
electrical outlet before leaving.
6. service
a. have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.
9.
The battery charger gets hot
during use. The charger’s
heat can build up to unsafe
levels and create a fire hazard
if it does not receive adequate
ventilation, due to an electrical fault, or if
it is used in a hot environment.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not place the charger on a flammable
surface. Do not obstruct any vents on
the charger. especially avoid placing
the charger on carpets and rugs; they
are not only flammable, but they also
obstruct vents under the charger.
Place the charger on a stable, solid,
nonflammable surface (such as a stable
metal workbench or concrete floor) at
least 1 foot away from all flammable
objects, such as drapes or walls. Keep a
fire extinguisher and a smoke detector in
the area. Frequently monitor the charger
and battery while charging.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)
13. WARNING: Handling the cord on this
product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)
10. This product is not a toy. Keep it out of
reach of children.
11. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure. In addition, people with
pacemakers should:
14. The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
• Avoid operating alone.
• Do not use with trigger locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
12. WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
blood circulation to the hand, past hand
injuries, nervous system disorders,
diabetes, or Raynaud’s Disease
should not use this tool. If you feel any
symptoms related to vibration (such as
tingling, numbness, and white or blue
fingers), seek medical advice as soon as
possible.
Lithium Battery safety Warnings
Lithium Batteries store a
Large amount oF energY and
WiLL Vent Fire or expLode iF
mistreated:
2. Do not smoke during use. Nicotine
reduces the blood supply to the hands
and fingers, increasing the risk of
vibration-related injury.
1. Keep Battery pack dry.
3. Wear suitable gloves to reduce the
vibration effects on the user.
2. do not do anY oF the
FoLLoWing to the BatterY paCK:
a. open,
4. Use tools with the lowest vibration when
there is a choice.
b. drop,
c. short‑circuit,
d. incinerate, or
5. Include vibration-free periods each day
of work.
6. Grip tool as lightly as possible (while still
keeping safe control of it). Let the tool
do the work.
e. expose to temperatures greater than
140°F.
3. Charge Battery Pack only according to
the instructions indicated in the charger
manual.
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
4. Inspect Battery Pack before every use;
do not use or charge if damaged.
saVe these
instruCtions.
Vibration safety
This tool vibrates during use. Repeated
or long-term exposure to vibration may
cause temporary or permanent physical
injury, particularly to the hands, arms
and shoulders. To reduce the risk of
vibration-related injury:
1. Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant
women or people who have impaired
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Double insulated tools may be used in
either of the 120 volt outlets shown in the
preceding illustration. (see outlets for
2‑prong plug.)
grounding
to preVent
eLeCtriC shoCK
and death From inCorreCt
grounding Wire
extension Cords
ConneCtion:
note: Extension cords must not be used with
Check with a qualified electrician
if you are in doubt as to whether
the outlet is properly grounded.
do not modify the power cord
plug provided with the tool.
never remove the grounding
prong from the plug. do not use
the tool if the power cord or plug
is damaged. if damaged, have it
repaired by a service facility
before use. If the plug will not fit
the outlet, have a proper outlet
installed by a qualified
this item’s charger.
symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
V~
electrician.
Amperes
a
n xxxx/min.
double insulated tools: tools with
two prong plugs
No Load Revolutions per Minute
(RPM)
0
outlets for 2‑prong plug
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the National
Electrical Code.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls
speCiFiCations
1. trigger:
Charger Input
120V~ / 60Hz
0-350 RPM (1st gear)
0-1200 RPM (2nd gear)
This is a variable speed tool.
Squeeze the Trigger more to increase
speed, less to reduce speed.
The light will illuminate when the trigger
is pressed.
Motor Speed
Battery
12V, 1300mAh Lithium-Ion
(ITEM 68059)
Chuck Capacity 3/8" (10mm)
2. direCtion setting:
unpaCKing
: (towards front of drill)
Press switch from the right side
of the drill to make the drill turn
clockwise, usually for tightening or
driving screws.
When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon as
possible.
: (away from front of drill)
Press switch from the left side
of the drill to make the drill turn
counterclockwise, usually for
loosening or removing screws.
instruCtions For putting
into use
read the entire important
saFetY inFormation
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
3. CLutCh CoLLar:
1 ‑ 11: These settings control the amount
of torque at the bit to prevent
stripping bolts and screws or
splitting wood.
Settings range from 1 - lowest
torque - to 11 - highest torque.
Functions
: This setting prevents the clutch
from slipping. It is used when
drilling holes.
Clutch
Collar
gear switch
Chuck
Collar
4. gear sWitCh:
1: low gear, higher torque
2: high gear, faster speed
direction
switch
Light
Caution to prevent drill damage,
do not adjust any setting halfway
between options.
trigger
example:
do not use the drill with the Clutch
collar set between settings 11 and .
Battery
pack
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Pack
operating instruCtions
read the entire important
saFetY inFormation
Green
Light
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.
Charging the Battery pack
Red Light
The Battery Pack (ITEM 68059) needs to
be charged before first use. Recharge
the Battery after every use.
Charger
1. Remove the Battery Pack by pressing on
the striped side tabs and sliding it out.
Then set the Pack and Charger on a dry
fireproof surface in a room where the
temperature ranges from 50-104° F.
3. The green light will activate once
Charger is plugged in. The green light
will continue to light and the red light will
flash during charging.
note: Normal charging time after use is
note: Allow a recently used Battery Pack
to cool completely before charging.
Also make sure the Battery Pack is
undamaged; do not charge a cracked or
leaking pack.
about 45 minutes.
4. When Battery Pack is fully charged, both
red and green lights will stay lit.
note: If both the green and red lights of the
charger are blinking simultaneously, the
charger or the battery is defective.
2. Insert Charger’s plug into a grounded,
120V~ outlet. Then slide Battery Pack
into Charger’s battery port, making sure
Battery Pack’s tabs snap into place and
Battery Pack is secure before charging.
note: Batteries will not reach full charge the
first time they are charged. Allow for
several cycles (drilling and recharging)
before the Tool is fully charged.
5. Press Battery Pack’s side tabs and pull
Pack from the Charger and unplug the
Charger from the wall outlet.
note: Do not use a battery pack immediately
after charging. Allow it to cool first. Store
the Charger and Battery Packs not in
use indoors, away from children.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
tool set up
general operating instructions
to preVent
serious injurY
From aCCidentaL
1. Change Direction, Clutch, and Gear
settings as desired, see page 8.
Caution: to prevent damage, do
not adjust any setting while drill is in
motion.
operation:
release the trigger and remove
the Battery pack before adjusting
tool or installing accessories.
2. Install bit as explained to the left.
3. Insert Battery Pack into base of tool until
it clicks in place.
Bit instaLLation:
1. Caution! Let bit cool before
touching, changing or adjusting it.
Bits heat up dramatically while in use,
and can burn you.
4. Place tip of bit against desired location.
Verify that work surface has no
hidden utility lines before drilling or
driving screws.
2. Slide Direction Selector to its mid-
5. Place one hand over top of housing for
greater tool stability. With other hand
grip handle and squeeze Trigger to
activate motor.
position.
3. While holding ring behind collar of
Chuck with one hand, rotate collar
counterclockwise to open jaws.
6. do not force bit. excessive force will
damage tip and lead to tool failure.
drill only as deep as needed.
4. Insert shank of drill bit or other accessory
into chuck.
5. Turn collar clockwise to hand tighten.
Caution! to prevent injury, do not
squeeze trigger to release or tighten
chuck.
7. To prevent accidents: After use, turn off
the tool and remove the Battery Pack
by pressing on the striped side tabs and
sliding it out. Clean, then store the tool
indoors out of children’s reach.
Work piece and Work area set up
1. Designate a work area that is clean and
well-lit. The work area must not allow
access by children or pets to prevent
distraction and injury.
2. Secure loose work pieces using a vise
or clamps (not included) to prevent
movement while working.
3. There must not be objects, such as utility
lines, nearby that will present a hazard
while working.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning, maintenance, and
Lubrication
maintenanCe and
serViCing
1. BeFore eaCh use, inspect the
general condition of the tool. Check for
loose hardware, misalignment or binding
of moving parts, cracked or broken parts,
damaged electrical wiring, and any
other condition that may affect its safe
operation.
Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
to preVent
serious injurY
From aCCidentaL
operation:
release the trigger and remove
the Battery pack before
performing any inspection,
maintenance, or cleaning
procedures.
2. aFter use, wipe external surfaces of
the tool with clean cloth.
3. dispose of Battery pack properly. do
not short, incinerate or open Battery
pack. Keep Charger and Battery pack
dry.
to preVent serious injurY
From tooL FaiLure:
do not use damaged equipment.
if abnormal noise or vibration
occurs, have the problem
corrected before further use.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
problem
Tool will not start.
possible Causes
1. Battery not installed or properly
charged.
Likely solutions
1. Check that battery is properly installed and fully
charged.
2. Internal damage or wear.
(Wiring or Trigger, for example.)
1. Accessory dull or damaged.
2. Have technician service tool.
Performance
decreases over time.
1. Keep cutting accessories sharp. Replace as
needed.
2. Carbon brushes worn or
damaged.
2. Have qualified technician replace brushes.
Excessive noise or Internal damage or wear.
Have technician service tool.
rattling.
Overheating.
(Motor bearings, for example.)
1. Forcing tool to work too fast.
1. Allow tool to work at its own rate.
2. Accessory misaligned.
2. Check and correct accessory to fence and/or
table alignment.
3. Accessory dull or damaged.
4. Blocked motor housing vents.
3. Keep cutting accessories sharp. Replace as
needed.
4. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator while
blowing dust out of motor using compressed air.
Follow all safety precautions whenever diagnosing or servicing the tool.
disconnect battery before service.
pLease read the FoLLoWing CareFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
record product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
parts List and diagram
part
description
Qty.
part
description
Qty.
1
2
3
4
5
6
7
8
9
Keyless Chuck
1
1
3
7
1
1
1
2
1
1
1
12 Rear Cover
1
1
1
1
3
1
1
Front Cover
Screw
13 Wire
14 White LED
15 LED Cover
16 Screw
17 Terminal Board
18 Screw
Screw
Gear Switch
Trigger
Direction Switch
Gear Switch Spring
Left Housing
Battery Pack - ITEM 68059
(12V, 1300mAh Lithium-Ion)
19
1
10 Right Housing
11 Gear Box
20 Motor
21 Charger (not shown)
1
1
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaint must accompany the merchandise.
If our inspection verifies the defect, we
will either repair or replace the product at
our election or we may elect to refund the
purchase price if we cannot readily and
quickly provide you with a replacement. We
will return repaired products at our expense,
but if we determine there is no defect, or that
the defect resulted from causes not within the
scope of our warranty, then you must bear the
cost of returning the product.
Limited 90 daY WarrantY
Harbor Freight Tools Co. makes every
effort to assure that its products meet
high quality and durability standards, and
warrants to the original purchaser that this
product is free from defects in materials and
workmanship for the period of 90 days from
the date of purchase. This warranty does not
apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities,
criminal activity, improper installation, normal
wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries
to persons or property, or for incidental,
contingent, special or consequential damages
arising from the use of our product. Some
states do not allow the exclusion or limitation
of incidental or consequential damages,
so the above limitation of exclusion may
not apply to you. THIS WARRANTY IS
ExPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, ExPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF
This warranty gives you specific legal
rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009
Camarillo, CA 93011 • (800) 444-3353
MERCHANTABILITY AND FITNESS.
SKU 69360
For technical questions, please call 1‑800‑444‑3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|