Chicago Electric Clock Radio 97427 User Manual

DUAL DOWEL JOINTER  
120V/60hZ  
Model 97427  
SET Up AND OpERATINg INSTRUcTIONS  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
®
Distributed exclusively by harbor Freight Tools .  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit our website at: http://www.harborfreight.com  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE ThIS MANUAL.  
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
outlets will reduce risk of electric  
shock.  
before plugging in. Carrying power  
tools with your finger on the switch  
or plugging in power tools that have  
the switch on invites accidents.  
b. Avoid body contact with grounded  
surfaces such as pipes, radiators,  
ranges and refrigerators. There is  
an increased risk of electric shock if  
your body is grounded.  
d. Remove any adjusting key or wrench  
before turning the power tool on. A  
wrench or a key left attached to a  
rotating part of the power tool may  
result in personal injury.  
c. Do not expose power tools to rain  
or wet conditions. Water entering a  
power tool will increase the risk of  
electric shock.  
e. Do not overreach. Keep proper  
footing and balance at all times.  
This enables better control of the  
power tool in unexpected situations.  
d. Do not abuse the cord. Never use  
the cord for carrying, pulling or  
unplugging the power tool. Keep  
cord away from heat, oil, sharp  
edges or moving parts. Damaged or  
entangled cords increase the risk of  
electric shock.  
f. Dress properly. Do not wear loose  
clothing or jewelry. Keep your hair,  
clothing and gloves away from  
moving parts. Loose clothes, jewelry  
or long hair can be caught in moving  
parts.  
e. When operating a power tool  
outdoors, use an extension cord  
suitable for outdoor use. Use of  
a cord suitable for outdoor use  
reduces the risk of electric shock.  
g. If devices are provided for the  
connection of dust extraction and  
collection facilities, ensure these are  
connected and properly used. Use  
of these devices can reduce dust-  
related hazards.  
3. personal safety  
a. Stay alert, watch what you are  
doing and use common sense  
when operating a power tool. Do  
not use a power tool while you are  
tired or under the influence of drugs,  
alcohol or medication. A moment  
of inattention while operating power  
tools may result in serious personal  
injury.  
4. power tool use and care  
a. Do not force the power tool. Use  
the correct power tool for your  
application. The correct power tool  
will do the job better and safer at the  
rate for which it was designed.  
b. Do not use the power tool if the  
switch does not turn it on and  
off. Any power tool that cannot  
be controlled with the switch is  
dangerous and must be repaired.  
b. Use safety equipment. Always wear  
eye protection. Safety equipment  
such as dust mask, non-skid  
safety shoes, hard hat, or hearing  
protection used for appropriate  
conditions will reduce personal  
injuries.  
c. Disconnect the plug from the power  
source and/or the battery pack from  
the power tool before making any  
adjustments, changing accessories,  
or storing power tools. Such  
c. Avoid accidental starting. Ensure  
the switch is in the off-position  
preventive safety measures reduce  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
the risk of starting the power tool  
accidentally.  
vibration may cause temporary or  
permanent physical injury, particularly  
to the hands, arms and shoulders. To  
reduce the risk of vibration-related  
injury:  
d. Store idle power tools out of the  
reach of children and do not allow  
persons unfamiliar with the power  
tool or these instructions to operate  
the power tool. Power tools are  
dangerous in the hands of untrained  
users.  
1. Anyone using vibrating tools regularly  
or for an extended period should  
first be examined by a doctor and  
then have regular medical check-  
ups to ensure medical problems are  
not being caused or worsened from  
use. Pregnant women or people  
who have impaired blood circulation  
to the hand, past hand injuries,  
e. Maintain power tools. Check for  
misalignment or binding of moving  
parts, breakage of parts and any  
other condition that may affect the  
power tool’s operation. If damaged,  
have the power tool repaired before  
use. Many accidents are caused by  
poorly maintained power tools.  
nervous system disorders, diabetes,  
or Raynaud’s Disease should not  
use this tool. If you feel any medical  
or physical symptoms related to  
vibration (such as tingling, numbness,  
and white or blue fingers), seek  
f. Keep cutting tools sharp and clean.  
Properly maintained cutting tools  
with sharp cutting edges are less  
likely to bind and are easier to  
control.  
medical advice as soon as possible.  
2. Do not smoke during use. Nicotine  
reduces the blood supply to the  
hands and fingers, increasing the risk  
of vibration-related injury.  
g. Use the power tool, accessories and  
tool bits etc., in accordance with  
these instructions and in the manner  
intended for the particular type of  
power tool, taking into account the  
working conditions and the work to  
be performed. Use of the power tool  
for operations different from those  
intended could result in a hazardous  
situation.  
3. Wear suitable gloves to reduce the  
vibration effects on the user.  
4. Use tools with the lowest vibration  
when there is a choice between  
different processes.  
5. Include vibration-free periods each  
day of work.  
5. Service  
a. Have your power tool serviced by  
a qualified repair person using only  
identical replacement parts. This will  
ensure that the safety of the power  
tool is maintained.  
6. Grip tool as lightly as possible (while  
still keeping safe control of it). Let  
the tool do the work.  
7. To reduce vibration, maintain the tool  
as explained in this manual. If any  
abnormal vibration occurs, stop use  
immediately.  
Vibration hazard  
This tool vibrates during use.  
Repeated or long-term exposure to  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. Use clamps (not included) or other  
practical ways to secure and support  
the workpiece to a stable platform.  
Holding the work by hand or against  
your body is unstable and may lead  
to loss of control.  
Specific Safety Rules  
1. Maintain labels and nameplates on  
the tool. These carry important safety  
information. If unreadable or missing,  
contact Harbor Freight Tools for a  
replacement.  
13. This product is not a toy. Keep it out  
of reach of children.  
2. Always examine the workpiece for  
foreign objects. Never attempt to cut  
into nails or other metal objects.  
14. People with pacemakers should  
consult their physician(s) before  
use. Electromagnetic fields in close  
proximity to heart pacemaker could  
cause pacemaker interference or  
pacemaker failure. In addition,  
people with pacemakers should:  
• Avoid operating alone.  
3. Always keep your hands and fingers  
well away from the chip ejection area  
while the tool is running.  
4. Avoid unintentional starting. Prepare  
to begin work before turning on the  
tool.  
• Do not use with power switch locked  
on.  
• Properly maintain and inspect to  
avoid electrical shock.  
• Any power cord must be properly  
grounded. Ground Fault Circuit  
Interrupter (GFCI) should also be  
implemented – it prevents sustained  
electrical shock.  
5. Begin cutting only when the Bits have  
reached full speed.  
6. Keep the Cutter Head and Drive  
Guards in place and in proper  
working order.  
7. Do not make jointing or planing cuts  
deeper than 1/8 inch.  
15. Some dust created by power  
sanding, sawing, grinding, drilling,  
and other construction activities,  
contains chemicals known [to the  
State of California] to cause cancer,  
birth defects or other reproductive  
harm. Some examples of these  
chemicals are:  
8. Use hold-down/push blocks for  
jointing material narrower than 3  
inches, or planing material thinner  
than 3 inches.  
9. Do not perform jointing or planing  
cuts on pieces shorter than 8 inches  
in length.  
• Lead from lead-based paints  
• Crystalline silica from bricks and  
cement or other masonry products  
• Arsenic and chromium from  
10. Do not lay the tool down until it has  
come to a complete stop. Moving  
parts can grab the surface and pull  
the tool out of your control.  
chemically treated lumber  
Your risk from these exposures  
varies, depending on how often you  
do this type of work. To reduce your  
exposure to these chemicals: work in  
a well ventilated area, and work with  
11. Do not leave the tool unattended  
when it is plugged into an electrical  
outlet. Turn off the tool, and unplug  
it from its electrical outlet before  
leaving.  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
approved safety equipment, such as  
those dust masks that are specially  
designed to filter out microscopic  
particles. (California Health & Safety  
Code § 25249.5, et seq.)  
grounded Tools: Tools with Three  
prong plugs  
16. The warnings, precautions,  
and instructions discussed in  
this instruction manual cannot  
cover all possible conditions and  
situations that may occur. It must  
be understood by the operator that  
common sense and caution are  
factors which cannot be built into this  
product, but must be supplied by the  
operator.  
3-prong plug and Outlet  
1. Tools marked with “Grounding  
Required” have a three wire cord  
and three prong grounding plug.  
The plug must be connected to a  
properly grounded outlet. If the tool  
should electrically malfunction or  
break down, grounding provides a  
low resistance path to carry electricity  
away from the user, reducing the risk  
of electric shock. (See 3-prong plug  
and Outlet.)  
SAVE ThESE  
INSTRUcTIONS.  
gROUNDINg  
TO pREVENT  
ELEcTRIc ShOck  
WARNINg  
2. The grounding prong in the plug is  
connected through the green wire  
inside the cord to the grounding  
system in the tool. The green wire  
in the cord must be the only wire  
connected to the tool’s grounding  
system and must never be attached  
to an electrically “live” terminal. (See  
3-prong plug and Outlet.)  
AND DEATh FROM  
INcORREcT gROUNDINg  
WIRE cONNEcTION:  
Check with a qualified  
electrician if you are in doubt  
as to whether the outlet is  
properly grounded. Do not  
modify the power cord plug  
provided with the tool. Never  
remove the grounding prong  
from the plug. Do not use the  
tool if the power cord or plug  
is damaged. If damaged, have  
it repaired by a service facility  
before use. If the plug will not  
fit the outlet, have a proper  
outlet installed by a qualified  
electrician.  
3. The tool must be plugged into an  
appropriate outlet, properly installed  
and grounded in accordance with all  
codes and ordinances. The plug and  
outlet should look like those in the  
preceding illustration. (See 3-prong  
plug and Outlet.)  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
example, a 14 gauge cord can carry  
a higher current than a 16 gauge  
cord. (See Table A.)  
Double Insulated Tools: Tools  
with Two prong plugs  
3. When using more than one extension  
cord to make up the total length,  
make sure each cord contains at  
least the minimum wire size required.  
(See Table A.)  
4. If you are using one extension cord  
for more than one tool, add the  
nameplate amperes and use the sum  
to determine the required minimum  
cord size. (See Table A.)  
Outlets for 2-prong plug  
1. Tools marked “Double Insulated”  
do not require grounding. They  
have a special double insulation  
system which satisfies OSHA  
requirements and complies with the  
applicable standards of Underwriters  
Laboratories, Inc., the Canadian  
Standard Association, and the  
National Electrical Code. (See  
Outlets for 2-prong plug.)  
5. If you are using an extension cord  
outdoors, make sure it is marked with  
the suffix “W-A” (“W” in Canada) to  
indicate it is acceptable for outdoor  
use.  
6. Make sure the extension cord is  
properly wired and in good electrical  
condition. Always replace a damaged  
extension cord or have it repaired by  
a qualified electrician before using it.  
2. Double insulated tools may be used  
in either of the 120 volt outlets shown  
in the preceding illustration. (See  
Outlets for 2-prong plug.)  
7. Protect the extension cords from  
sharp objects, excessive heat, and  
damp or wet areas.  
Extension cords  
1. Grounded tools require a three wire  
extension cord. Double insulated  
tools can use either a two or three  
wire extension cord.  
2. As the distance from the supply  
outlet increases, you must use a  
heavier gauge extension cord. Using  
extension cords with inadequately  
sized wire causes a serious drop in  
voltage, resulting in loss of power and  
possible tool damage.  
(See Table A.) The smaller the  
gauge number of the wire, the  
greater the capacity of the cord. For  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note: For additional information regarding  
the parts listed in the following pages,  
refer to the Assembly Diagram near  
the end of this manual.  
SpEcIFIcATIONS  
120 V~ / 60 Hz  
3.55 No Load Amps / 710 Watts  
Power Plug Type: 2-Prong, Polarized  
Power Switch Type: Lockable for  
continuous run  
Electrical  
Requirements  
Motor RPM  
16,500  
Drill Bit Diameter 1/4” (Qty 2)  
Assembly  
Maximum Drilling  
1-7/16”  
Depth  
Width Between  
Drilling Holes  
To Install The Drill Bits:  
1-5/16” (On Center)  
Fence  
Adjustments  
1. Rotate the two Chucks (18) so that  
their Hex Screws (19) are on top.  
(See Figure A.)  
22-1/2° / 45° / 67-1/2° / 90°  
UNpAckINg  
2. Use the provided Hex Key (86) to  
loosen the two Hex Screws (19).  
(See Figure A.)  
When unpacking, check to make sure  
that the item is intact and undamaged. If  
any parts are missing or broken, please  
call Harbor Freight Tools at the number  
shown on the cover of this manual as soon  
as possible.  
3. Insert the shafts of the two Bits (17)  
(with flat face of shank facing the  
screw) fully into the two Chucks (18).  
4. Secure the Bits (17) into the Chucks  
(18) by using the Hex Key (86) to  
firmly tighten the Hex Screws (19).  
(See Figure A.)  
INITIAL SET Up  
INSTRUcTIONS  
Read the ENTIRE IMpORTANT  
SAFETY INFORMATION section  
at the beginning of this manual  
including all text under  
subheadings therein before set  
up or use of this product.  
hEX ScREW  
(19)  
hEX ScREW  
(19)  
TO pREVENT  
SERIOUS INJURY  
WARNINg  
chUck (18)  
chUck (18)  
FROM AccIDENTAL  
OpERATION:  
Turn the power Switch of the  
tool to its “OFF” position and  
unplug the tool from its  
electrical outlet before  
assembling or making any  
adjustments to the tool.  
FIgURE A  
(TOp VIEW)  
To Adjust The cutting Depth:  
1. Move the Motor Base (16) as far back  
as it will go. (See Figure B.)  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Loosen the Screw (47), and set the  
cutting depth by sliding the Depth  
Tab (48) along the Depth Ruler (49).  
(See Figure B.)  
3. Retighten the Clamping Lever (12).  
(See Figure D.)  
4. NOTE: The height must correspond  
to half the thickness of the workpiece.  
Also, the groove of the Guide Plate  
(8) must always be in the middle of  
the workpiece.  
3. Retighten the Knob Screw (47) to  
lock the adjustment in place. (See  
Figure B.)  
knob  
ScREW  
(47)  
FIgURE D  
FIgURE B  
hEIghT  
ADJUSTMENT  
(14)  
DEpTh  
TAB  
(48)  
DEpTh RULER  
(49)  
MOTOR BASE (16)  
cLAMpINg  
LEVER  
(12)  
To Adjust The cutting Angle:  
gUIDE  
pLATE  
(8)  
1. Loosen the Knob (59).  
(See Figure c.)  
2. Move the Angle Stop (3) to the  
desired angle. (See Figure c.)  
3. Retighten the Knob (59).  
(See Figure c.)  
FIgURE c  
kNOB  
(59)  
OpERATINg INSTRUcTIONS  
Read the ENTIRE IMpORTANT  
SAFETY INFORMATION section  
at the beginning of this manual  
including all text under  
subheadings therein before set  
up or use of this product.  
ANgLE  
STOp  
(3)  
The power Switch:  
1. To turn on the Dowel Jointer, move  
the Power Switch (74) forward.  
(See Figure E, next page.)  
To Adjust The height:  
1. Loosen the Clamping Lever (12).  
(See Figure D.)  
2. NOTE: The Power Switch (74) is  
lockable for continuous running. To  
lock the Power Switch in its “ON”  
position, move the Switch all the way  
forward until it locks in place.  
2. Move the Height Adjustment Lever  
(14) to the desired height, using the  
Scale on the Guide Plate (8).  
(See Figure D.)  
(See Figure E, next page.)  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. To turn off the Dowel Jointer, move  
the Power Switch (74) all the way  
backward. (See Figure E.)  
5. Push the Motor Base (16) carefully  
forward as far as possible.  
6. When finished cutting, move the  
Motor Base (16) backward, and turn  
the Dowel Jointer off.  
FIgURE E  
To Join The Workpieces:  
1. When the holes in the workpieces  
have been made, the workpieces can  
be joined together.  
2. Place wood glue in both grooves of  
the workpieces.  
pOWER  
SWITch  
(74)  
3. Place a dowel pin in the hole of one  
workpiece.  
4. Insert the other workpiece onto the  
dowel pin.  
To Mark The Workpiece:  
1. Before starting with the Dowel Jointer,  
the workpieces must be marked as  
follows:  
5. Clamp the workpieces together.  
Then wait until the glue is dry. (Read  
glue manufacturer’s instruction.)  
a. Place the two workpieces on top of  
each other.  
b. Secure the workpieces, using a vise  
or clamps (neither included).  
MAINTENANcE & SERVIcINg  
c. Mark the center of the grooves.  
TO pREVENT  
SERIOUS INJURY  
WARNINg  
FROM AccIDENTAL  
OpERATION:  
To position the Dowel Jointer for Large  
Workpieces:  
Turn the power Switch of the  
tool to its “OFF” position and  
unplug the tool from its  
electrical outlet before  
performing any inspection,  
maintenance, or cleaning  
procedures.  
1. Place the Dowel Jointer near the  
workpieces.  
2. The middle of the Motor Base (16),  
which is marked on the Guide Plate  
(8), must face the center of the  
groove in the workpiece.  
3. Move the Motor Base (16) backward.  
4. Hold the Dowel Jointer with both  
hands, and turn the tool on.  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TO pREVENT SERIOUS  
INJURY FROM TOOL  
FAILURE:  
Do not use damaged  
equipment. If abnormal noise  
or vibration occurs, have the  
problem corrected before  
further use.  
2. BEFORE EAch USE, check to make  
sure the Bits (17) are firmly secured  
in place, sharp, and free of cracks or  
bends.  
3. AFTER USE, clean external surfaces  
of the tool with a clean, moist cloth  
and mild detergent. Do not use  
solvents.  
Inspection, Maintenance, and  
cleaning  
4. WhEN STORINg, keep the tool and  
its accessories in its Carrying Case.  
Make sure to store the Carrying  
Case in a clean, dry, safe location  
out of reach of children and other  
unauthorized people.  
1. BEFORE EAch USE, inspect the  
general condition of the tool. Check  
for loose screws, misalignment or  
binding of moving parts, cracked or  
broken parts, damaged electrical  
wiring, and any other condition that  
may affect its safe operation.  
5.  
WARNINg! If the supply cord of  
this power tool is damaged, it must  
be replaced only by a qualified  
service technician.  
TROUBLEShOOTINg  
problem  
possible causes  
possible Solutions  
Tool will not start  
1. No power at outlet.  
1. Check power at outlet.  
2. Cord not connected.  
2. Check that cord is plugged in.  
Tool produces  
unsatisfactory  
cuts.  
1. Bits not firmly secured.  
1. Make sure Bits are firmly secured in the  
Chucks.  
2. Bits are dull.  
2. Use only sharp Bits.  
3. Bits are cracked or bent.  
3. Replace with new Bits.  
Follow all safety precautions whenever diagnosing or servicing the tool.  
Disconnect power supply before service.  
pLEASE READ ThE FOLLOWINg cAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL  
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR  
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT,  
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/  
OR DISTRIBUTOR ExPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY  
CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
pARTS LIST  
46 Wood-ruff key 3×10  
47 Knob Screw  
48 Depth Tab  
49 Depth ruler  
50 square nut M5  
51 spring cap  
52 spring for fixing pin  
53 pin  
54 Slide bush  
55 finger  
56 cross panhead screw M3x6  
57 steel ball Ø5  
58 Spring  
59 short knob  
60 bend tube  
61 cross panhead screw M4x52  
62 rotor  
63 rubber bearing cover  
64 cross panhead screw M4x52  
65 stator  
66 slide switch knob  
67 housing  
68 switch bar  
2
1
1
1
1
2
2
2
2
1
1
1
1
1
1
2
1
1
2
1
1
1
1
4
No Specifications  
Qty  
2
1
1
1
9
3
1
1
1
1
1
1
1
1
2
1
2
2
2
4
1
2
1
1
2
5
4
1
2
3
4
5
6
7
8
9
cross sunk-head screw M4×6  
front plate  
angle stop  
orientation block  
washer 4  
cross panhead screw M4×8  
hexagon bolt M5×25  
guide plate  
fixing spring  
10 lock clamp  
11 hex nut  
12 Clamping Lever  
13 Check ring  
14 Height adjustable level  
15 cross sunk-head screw M4×12  
16 motor base  
17 bit  
18 Chuck  
19 inner hexagon set screw M4×5  
20 cross panhead screw M4×10  
21 Front cap  
22 oil bearing  
23 shaft  
24 middle gear  
25 checking ring 12  
26 big flat washer 5  
27 cross panhead self-tapping screw  
69 cross panhead self-tapping screw  
ST4x12  
70 switch holder  
1
1
1
1
1
1
2
2
4
2
71 cable clamp  
72 switch clamp  
73 spring  
74 power switch  
75 capacitor 0.22uF  
76 brush holder  
77 carbon brush  
78 rivet 3x10  
ST4.2×16  
28 reduction box  
1
1
1
1
1
1
29 wind baffle  
30 handle  
31 flat washer 6  
32 spring washer 6  
33 inner hexagon column-head screw  
79 cross panhead self-tapping screw  
ST4x14  
M6x20  
80 clamp for choke  
1
2
1
1
1
1
1
34 bearing 80101  
1
1
2
2
1
3
2
2
2
1
4
2
81 cross panhead self-tapping ST3x10  
82 back cover  
83 flat washer 4  
84 cable jacket  
85 cable plug  
35 29 bearing cover  
36 cross sunk-head screw M4x8  
37 cross panhead screw M4x16  
38 blocker  
39 bearing 80017  
40 Check Ring 9  
41 gear  
42 bearing 80019  
43 bearing cover for bearing cover  
44 cross sunk-head screw M4x8  
45 circlip  
86 hex key  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY DIAgRAM  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED 1 YEAR / 90 DAY WARRANTY  
Harbor Freight Tools Co. makes every effort to assure that its products meet high  
quality and durability standards, and warrants to the original purchaser that for a period  
of ninety days from date of purchase that the engine/motor, the belts (if so equipped),  
and the blades (if so equipped) are free of defects in materials and workmanship. Harbor  
Freight Tools also warrants to the original purchaser, for a period of one year from date  
of purchase, that all other parts and components of the product are free from defects in  
materials and workmanship (90 days if used by a professional contractor or if used as rental  
equipment). This warranty does not apply to damage due directly or indirectly, to misuse,  
abuse, negligence or accidents, repairs or alterations outside our facilities, normal wear and  
tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons  
or property, or for incidental, contingent, special or consequential damages arising from  
the use of our product. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so the above limitation of exclusion may not apply to you. THIS  
WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR  
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with  
transportation charges prepaid. Proof of purchase date and an explanation of the complaint  
must accompany the merchandise. If our inspection verifies the defect, we will either  
repair or replace the product at our election or we may elect to refund the purchase price  
if we cannot readily and quickly provide you with a replacement. We will return repaired  
products at our expense, but if we determine there is no defect, or that the defect resulted  
from causes not within the scope of our warranty, then you must bear the cost of returning  
the product.  
This warranty gives you specific legal rights and you may also have other rights which  
vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
Record product’s Serial Number here:  
Note: If product has no serial number, record month and year of purchase instead.  
Note: Some parts are listed and shown for illustration purposes only, and are not  
available individually as replacement parts.  
SKU 97427  
For technical questions, please call 1-800-444-3353.  
Page 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bionaire Electric Heater BCH9208 User Manual
Black Decker Iron AS800 User Manual
Briggs Stratton Lawn Mower 1687077 User Manual
Bushnell Binoculars 26 2024 User Manual
Cadillac Automobile 2008 CTS User Manual
Canon Camcorder 2686B001 User Manual
Canon Digital Camera 3814B004 User Manual
Carrier Air Conditioner 38TXA User Manual
Cary Audio Design DJ Equipment Cinema 11a User Manual
Chevrolet Automobile 2008 Corvette User Manual