Chauvet Work Light TFX 950CM User Manual

TFX-950CM  
Stage Wash950  
USER MANUAL  
Chauvet, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A  
(800) 762-1084 (954) 929-1115  
FAX (954) 929-5560  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BEFORE YOU BEGIN  
What is included  
1 x Stage Wash950CM (TFX-950CM)  
Power cord with plug  
3 x EHM 300w 120v or 3 x EHM2 300w 230v lamps  
Warranty Card & Manual  
Unpacking Instructions  
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that  
all parts are present, and have been received in good condition. Notify the shipper immediately and  
retain packing material for inspection if any parts appear damaged from shipping or the carton itself  
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture  
must be returned to the factory, it is important that the fixture be returned in the original factory box  
and packing.  
AC Power  
To determine the power requirements for a particular fixture, see the label affixed to the back plate of  
the fixture or refer to the fixtures specifications chart. A fixtures listed current rating is its average  
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and  
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer  
channel is used solely for a 0% to 100% switch. Before applying power to a  
AC Voltage Switch  
fixture, check that the source voltage matches the fixtures requirement. Check  
the fixture or device carefully to make sure that if a voltage selection switch  
exists that it is set to the correct line voltage you will use.  
Warning!  
Verify that the power select switch on your unit matches the  
line voltage applied. All fixtures must be connected to circuits  
with a suitable Earth Ground.  
Safety Instructions  
Please read these instructions carefully, which includes important information about the installation,  
usage and maintenance?  
Please keep this User Guide for future consultation. If you  
sell the unit to another user, be sure that they also receive  
this instruction booklet.  
Secure fixture to fastening device using a safety chain.  
Never carry the fixture solely by its head. Use its carrying  
handles.  
Maximum ambient temperature is Ta: 40°. Do not operate  
fixture at temperatures higher than this.  
In the event of serious operating problem, stop using the  
unit immediately. Never try to repair the unit by yourself.  
Repairs carried out by unskilled people can lead to  
damage or malfunction. Please contact the nearest  
authorized technical assistance center. Always use the  
same type spare parts.  
Dont connect the device to a dimmer pack.  
Make sure power cord is never crimped or damaged.  
Never disconnect power cord by pulling or tugging on the  
cord.  
Always make sure that you are connecting to the proper  
voltage and that the line voltage you are connecting to is  
not higher than that stated on decal or rear panel of the  
fixture.  
This product is intended for indoor use only!  
To prevent risk of fire or shock, do not expose fixture to  
rain or moisture. Make sure there are no flammable  
materials close to the unit while operating.  
The unit must be installed in a location with adequate  
ventilation, at least 50cm from adjacent surfaces. Be sure  
that no ventilation slots are blocked.  
Always disconnect from power source before servicing or  
replacing lamp or fuse and be sure to replace with same  
lamp source.  
Avoid direct eye exposure to lamp while it is on.  
Caution!  
There are no user serviceable parts inside the unit. Do not open the housing or  
attempt any repairs yourself. In the unlikely event your unit may require service,  
please contact CHAUVET.  
TFX-950CM User Manual  
3
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
INTRODUCTION  
Features  
2-4 channel DMX RGB color wash fixture  
Operating modes:  
RGB Mode: Full RGB mix plus dimmer (4 channels)  
C&B Mode: Color selection (40 presets) and dimmer (2 channels)  
RGB & Chase Mode: 7 distinct operating modes (4 channels)  
- RGB mix, 8-pattern auto, 8-pattern sound, auto-chase, sound-chase, 40-color auto or sound  
Individual channel controls may include;  
- Red 0-100%, color selection or mode select  
- Green or Red 0-100%, dimmer 0-100%  
- Blue or Green 0-100%, fade time  
- Dimmer 0-100%, speed time  
900 watts of total brightness  
Built in beat activated and automatic programs (stand-alone)  
Barn doors  
Sound sensitivity knob  
Double bracket yoke doubles as floor stand  
Linkable via Master/Slave  
Fan cooled  
DMX Channel Summary  
RGB Mode  
Channel  
Function  
Red  
1
2
3
4
Green  
Blue  
Dimmer  
C&B (Color & Brightness) Mode  
Channel  
Function  
1
2
Color Selection  
Dimmer  
Combined RGB & Chase Mode  
Channel  
Function  
1
2
3
4
Control Mode  
Red or Dimming  
Green or Fade  
Blue or Speed  
For complete channel listing see DMX Values in the Appendix section.  
TFX-950CM User Manual  
4
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Introduction  
Product Overview  
LED status  
window  
DMX channel  
values and brief  
instructions  
Control panel  
buttons  
Fan  
DMX Input  
connector  
Sound  
sensitivity knob  
Built in  
microphone  
Voltage  
Selector Switch  
IEC power  
connector for  
power cable  
Fuse  
compartment  
DMX Output  
connector  
Foot controller  
connector for  
TFX-SWF  
TFX-950CM User Manual  
5
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
SETUP  
Lamp  
You will need to install a lamp prior to the initial operation of the fixture. Three EHM 300W halogen  
lamps are included.  
Warning!  
When replacing the lamp, please wait 15 minutes after powering down to allow the  
unit to cool down! Always disconnect from main power prior to lamp replacement.  
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp  
with alcohol and wipe it with a lint free cloth before installation.  
LAMP INSTALLATION  
TFX-950CM Lamp Installation  
1) Remove the 2 screws as illustrated in Figure 3,  
located on the front of the fixture and lift the entire  
cover plate until lamp reflectors are exposed.  
2) The linear lamp is held in place by tension provided by  
springs inside of both ceramic socket ends. It is  
important to proceed with lamp removal and  
Remove these 2 screws  
replacement very delicately.  
3) Hold linear lamp with a napkin and push in the  
direction of either of the two ends to relieve tension on  
the opposite end. Then pull end of lamp upwards to  
remove from socket.  
4) To replace lamp, follow the same procedure as above  
to insert lamp into the socket.  
5) Lower the cover plate and replace both screws.  
6) No lamp alignment is necessary for this fixture.  
Lamps exposed  
Power  
Your product is equipped with switch-selectable AC power  
Slide switch up or down  
setting.  
depending on your line voltage.  
Warning!  
Verify that the power select switch on your unit  
matches the line voltage applied. All fixtures must  
be connected to circuits with a suitable Earth  
Ground.  
To determine the power requirements for a particular fixture,  
see the label affixed to the back plate of the fixture or refer to  
the fixtures specifications chart.  
A fixtures listed current rating is its average current draw under normal conditions.  
All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable  
resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%  
switch.  
Before applying power to a fixture, check that the source voltage matches the fixtures requirement.  
All fixtures must be connected to circuits with a suitable Earth Ground.  
TFX-950CM User Manual  
6
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Setup  
Mounting  
ORIENTATION  
This fixture may be mounted in any position provided there is adequate room for ventilation.  
RIGGING  
Hanging Clamp  
It is important never to obstruct the fan or vents pathway. Mount the  
fixture using, a suitable Cor Otype clamp. Adjust the angle of the  
fixture by loosening both knobs and tilting the fixture. After finding  
the desired position, retighten both knobs.  
When selecting installation location, take into consideration lamp  
replacement access and routine maintenance.  
Safety cables should always be used.  
Note!  
Never mount in places where the fixture will be exposed to rain, high  
humidity, extreme temperature changes or restricted ventilation.  
Clamp is sold separately.  
DOUBLE BRACKET YOKE (FLOOR STAND)  
The TFX-950CM can also be positioned on the floor using its double bracket yoke. This product gets  
extremely hot under normal operation and you should take extreme care to avoid any contact what  
so ever with the fixture while in use. Be sure to keep all traffic at least 4 feet away from the fixtures  
position.  
TFX-950CM User Manual  
7
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
OPERATING INSTRUCTIONS  
Operating Modes  
The TFX-950CM can be operated in three ways.  
A stand-alone mode will listen to sound and run through its diverse range of built in programs. An  
optional TFX-SWF wired controller provides simple remote control.  
Master/Slave mode will allow the command of up to as many units you want in a synchronized light  
show to the sound.  
DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be controlled  
individually using any universal DMX-512 controller.  
Stand Alone Mode  
The Stand Alone mode is  
activated by setting the TFX-  
950CM to either AUDIO  
(Sound Active) or AUTO  
(Automatic) mode. The built in  
programs consist of a color  
chase and depending on the  
mode, two or three parameters  
can be modified as described  
next.  
AUDIO  
RGB&D  
C & B  
DMX Signal  
Received  
F:0:0:0
 
AUTO  
MODE  
UP  
DOWN  
AUDIO MODE (ALSO SOUND-ACTIVE)  
1) A steady hold of the MODE button will change the operating mode once then release the button.  
2) Repeat step 1 until you arrive at the AUDIO operating mode, as indicated by the LED next to the  
label.  
3) Two parameters will now become available for the AUDIO mode. Press the MODE button  
quickly to toggle between parameters.  
- F (for Fade time 0 ~ 100%)  
- D (for Dimming 0 ~ 100%)  
4) Use the UP and DOWN buttons to change values for each respective parameter.  
AUTOMATIC MODE  
1) A steady hold of the MODE button will change the operating mode once then release the button.  
2) Repeat step 1 until you arrive at the AUTO operating mode, as indicated by the LED next to the  
label.  
3) Three parameters will now become available for the AUTO mode. Press the MODE button  
quickly to toggle between parameters.  
- F (for Fade time 0 ~ 100%)  
- D (for Dimming 0 ~ 100%)  
- S (for Speed 0 ~ 100%)  
4) Use the UP and DOWN buttons to change values for each respective parameter.  
TFX-950CM User Manual  
8
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Operating Instructions  
Master/Slave  
The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In  
this mode, the first unit in the daisy chain will automatically command all other units following. An  
optional TFX-SWF controller connected to the first unit in the chain will allow enhanced control  
functions.  
MASTER/SLAVE SETTINGS  
1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector  
of the first fixture.  
2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin  
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,  
proceed to connect from the output as stated above to the input of the following fixture and so on  
as illustrated below in figure Daisy Chain Connection.  
Daisy Chain Connection  
Optional Controller  
Controller not required for  
Master/Slave operation  
Note!  
For additional information on linking fixtures read under section DMX Primer”  
DMX Mode  
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to  
customizing or creating a show. In this mode you will be able to control each individual trait of the  
fixture independently.  
SETTING THE STARTING ADDRESS  
This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start  
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data  
on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels  
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,  
102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate  
the start address selected for future reference.  
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping  
to the Appendix Section and read the heading DMX Primer. It contains very useful information that  
will help you understand its use.  
There are three different DMX  
channel configurations on the  
AUDIO  
RGB&D  
C & B  
Stage Wash. Each mode or  
configuration allows the user to  
control the fixure in a different  
manner using a universal DMX  
controller.  
DMX Signal  
Received  
A:0:0:1
 
AUTO  
MODE  
UP  
DOWN  
TFX-950CM User Manual  
9
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Operating Instructions  
RGB&D MODE  
All three lamps are individually dimmable giving the user  
the ability to customize or create the color of choice. This  
mode offers the user complete freedom.  
Channel  
Function  
1
2
3
4
Red  
Green  
Blue  
1) A steady hold of the MODE button will change the  
operating mode once then release the button.  
Dimmer  
2) Repeat step 1 until you arrive at the RGB&D  
operating mode, as indicated by the led next to the  
label.  
3) The display will now read parameter A: which represents the DMX channel address value. Use  
the UP and DOWN buttons to change values.  
C&B MODE  
This is called the Color and Brightness mode. Use channel  
Channel Function  
1 to move across the RGB spectrum.  
1
2
Spectrum Color Mix  
Dimmer  
1) A steady hold of the MODE button will change the  
operating mode once then release the button.  
See Color Mix Table in the  
appendix section.  
2) Repeat step 1 until you arrive at the C&B operating  
mode, as indicated by the led next to the label.  
3) The display will now read parameter A: which  
represents the DMX channel address value. Use the UP and DOWN buttons to change values.  
RGB & CHASE MODE  
This is the most diverse operating mode the Stage Wash  
Channel Function  
has to offer. It allows individual RGB mix control when  
1
2
3
4
Control Mode  
Red or Dimming  
Green or Fade  
Blue or Speed  
needed while still maintaining the ability to run built in  
automated chase programs.  
1) A steady hold of the MODE button will change the  
operating mode once then release the button.  
2) Repeat step 1 until both the RGB&D and the C&B led  
turn on.  
3) The display will now read parameter A: which represents the DMX channel address value. Use  
the UP and DOWN buttons to change values.  
TFX-950CM User Manual  
10  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Instructions  
TFX-SWF Easy Controller (Optional)  
The TFX-SWF Foot Controller is used only in master/slave mode. Connect the 8-pin connector of the  
foot controller into its respective connector on the first unit in the daisy chain. The table below  
describes the functions of the TFX-SWF Controller.  
TFX-SWF BUTTONS  
TFX-SWF Foot Controller  
Stand By Mode  
Function  
TFX-SWF  
Blackout Auto  
Fixtures will run built in programs  
Led 1: Off  
Led 2: Off  
automatically  
STAND-BY  
FUNCTION  
MODE  
Audio  
Led 1: Off  
Led 2: On  
Fixtures will run built in programs to  
the sound.  
Manual  
Full/CB:  
Led 1: On  
Led 2: Off  
Hold: pedal to set to Full On  
Bump: Pedal to set dimming levels  
Manual  
Full/CB:  
Led 1: On  
Led 2: On  
Hold: pedal to set dimming levels  
Release: Pedal to set to Full On  
TFX-CONPK Stage WashController Pack (Optional)  
The TFX-CONPK is a package that includes the TFX-32CON which is an enhanced dedicated  
controller for the TFX-950CM, TFX-64CM and TFX-1550CM fixtures. The TFX-32F foot controller is  
also included for hands-free operation.  
The TFX-32CON provides the following features:  
9 different hold-color buttons for  
immediate color access  
fader access to 40 predefined  
mixed colors  
TFX-32CON  
fade time control  
12 different chase patterns to  
choose from  
chase speed control  
master dimmer level  
blackout button  
full on button  
sound button  
The TFX-32F provides the following features:  
Selectable modes:  
1. Blackout  
2. Color Hold  
3. Chase  
TFX-32F  
Mode  
Up and down pedal buttons select  
colors and chase patterns  
Please refer to the TFX-32CON and TFX-32F user manuals for more in depth information.  
TFX-950CM User Manual  
11  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
APPENDIX  
DMX Primer  
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A  
fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user  
must assign a starting address on the fixture that indicates the first channel reserved in the controller.  
There are many different types of DMX controllable fixtures and they all may vary in the total number  
of channels required. Choosing a start address should be planned in advance. Channels should  
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is  
set incorrectly. You can however, control multiple fixtures of the same type using the same starting  
address as long as the intended result is that of unison movement or operation. In other words, the  
fixtures will be slaved together and all respond exactly the same.  
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is  
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which  
the fixtures are connected is not important and has no effect on how a controller communicates to  
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures  
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The  
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET  
carries 3-pin XLR DMX compliant cables, DMX-10 (33), DMX-4.5 (15) and DMX-1.5 (5)  
FIXTURE LINKING  
Figure 1 - DMX connector configuration  
Resistance 120  
1
ohm 1/4w between  
pin 2 (DMX -) and  
pin 3 (DMX +) of  
the last fixture.  
3
2
COMMON  
DMX +  
1
3
1
3
INPUT  
OUTPUT  
2
2
Termination reduces signal errors  
and to avoid signal transmission  
problems and interference, it is  
DMX -  
Note!  
If you use a controller with a 5 pin DMX output connector, you will need to use a 5  
pin to 3 pin adapter. Chauvet Model No: DMX5M.  
The chart below details a proper cable conversion:  
3 Pin to 5 Pin Conversion Chart  
Conductor  
3 Pin Female (output)  
5 Pin Male (Input)  
Pin 1  
Ground/Shield  
Data ( - )signal  
Data ( + ) signal  
Do not use  
Pin 1  
Pin 2  
Pin 3  
Pin 2  
Pin 3  
Do not use  
Do not use  
Do not use  
TFX-950CM User Manual  
12  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix  
DMX Channel Values  
RGB&D Mode (RGB and Dimmer)  
Channel  
Value  
Function  
Notes  
Red  
1
000 255  
000 255  
000 255  
000 255  
Intensity: 0% ~ 100%  
Green  
Intensity: 0% ~ 100%  
Blue  
Intensity: 0% ~ 100%  
Dimmer  
0 100%  
2
3
4
C&B Mode (Color and Brightness)  
Channel  
Value  
Function  
Notes  
Spectrum Color Mix  
See Color Mix Table  
Dimmer  
Intensity: 0% ~ 100%  
See Color Mix table on the next  
page  
1
000 255  
000 255  
2
RGB and Chase Mode  
Mode  
Ch 1 (Mode) Ch 2  
Ch 3  
Ch 4  
RGB Mode  
000 029  
030 094  
Red: 0 ~ 100% Green: 0 ~ 100% Blue: 0 ~ 100%  
Speed  
8 Built-in Programs (Auto)  
8 Built-in Programs (Sound) 094 159  
Chase (Auto)  
160 184  
185 209  
210 234  
235 255  
Dimming:  
0 ~ 100%  
Speed  
Speed  
Fade Time  
Chase (Sound)  
40 Color Chase (Auto)  
40 Color Chase (Sound)  
TFX-950CM User Manual  
13  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Appendix  
Color Mix Table (Preset)  
DMX Value  
Red Intensity  
0% ~ 100%  
0
Green Intensity  
0% ~ 100%  
0
Blue Intensity  
0% ~ 100%  
0
Notes  
0
Blackout  
1
2
100  
100  
0
0
0
0
Red @ Full only  
3
4
5
6
7
8
9
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
3
6
9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Red @ Full  
Proportional Green  
12  
15  
18  
21  
24  
27  
30  
33  
36  
39  
42  
45  
48  
51  
54  
57  
60  
63  
66  
69  
72  
75  
78  
81  
84  
87  
90  
93  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
100  
100  
0
Red & Green @ Full  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
97  
94  
91  
88  
85  
82  
79  
76  
73  
70  
67  
64  
61  
58  
55  
52  
49  
46  
43  
40  
37  
34  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Green @ Full  
Proportional Red  
TFX-950CM User Manual  
14  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
57  
58  
59  
60  
61  
62  
63  
64  
65  
31  
28  
25  
22  
19  
16  
13  
10  
7
100  
100  
100  
100  
100  
100  
100  
100  
100  
0
0
0
0
0
0
0
0
0
Green @ Full  
Proportional Red  
66  
67  
68  
69  
0
0
0
0
100  
100  
100  
100  
0
0
0
0
Green @ Full only  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
100  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
3
6
9
Green @ Full  
Proportional Blue  
12  
15  
18  
21  
24  
27  
30  
33  
36  
39  
42  
45  
48  
51  
54  
57  
60  
63  
66  
69  
72  
75  
78  
81  
84  
87  
90  
93  
101  
0
100  
100  
Green & Blue @ Full  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
97  
94  
91  
88  
85  
82  
79  
76  
73  
70  
67  
64  
61  
58  
55  
52  
49  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
Blue @ Full  
Proportional Green  
TFX-950CM User Manual  
15  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
119  
120  
121  
122  
123  
124  
125  
126  
127  
128  
129  
130  
131  
132  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
46  
43  
40  
37  
34  
31  
28  
25  
22  
19  
16  
13  
10  
7
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
Blue @ Full  
Proportional Green  
133  
134  
135  
136  
0
0
0
0
0
0
0
0
100  
100  
100  
100  
Blue @ Full only  
137  
138  
139  
140  
141  
142  
143  
144  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
3
6
9
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
Blue @ Full  
Proportional Red  
12  
15  
18  
21  
24  
27  
30  
33  
36  
39  
42  
45  
48  
51  
54  
57  
60  
63  
66  
69  
72  
75  
78  
81  
84  
87  
90  
93  
168  
100  
0
100  
Red & Blue @ Full  
169  
170  
171  
172  
173  
174  
175  
176  
177  
178  
179  
180  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
0
0
0
0
0
0
0
0
0
0
0
0
97  
94  
91  
88  
85  
82  
79  
76  
73  
70  
67  
64  
Red @ Full  
Proportional Blue  
TFX-950CM User Manual  
16  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
191  
192  
193  
194  
195  
196  
197  
198  
199  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
61  
58  
55  
52  
49  
46  
43  
40  
37  
34  
31  
28  
25  
22  
19  
16  
13  
10  
7
Red @ Full  
Proportional Blue  
200  
201  
202  
203  
204  
205  
206  
100  
100  
100  
100  
100  
100  
100  
6
12  
24  
36  
48  
60  
72  
84  
Red @ Full  
Proportional Green and Blue  
12  
18  
24  
30  
36  
42  
207  
100  
50  
100  
Red & Blue @ Full, Green @  
50%  
208  
209  
210  
88  
76  
64  
62  
74  
86  
100  
100  
100  
Blue @ Full  
Proportional Red and Green  
211  
50  
100  
100  
Green & Blue @ Full, Red @  
50%  
212  
213  
214  
215  
216  
217  
218  
219  
220  
221  
222  
223  
224  
225  
226  
227  
228  
44  
38  
32  
26  
19  
13  
7
12  
18  
24  
30  
38  
44  
50  
62  
74  
86  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
88  
76  
64  
52  
44  
38  
32  
25  
19  
13  
7
12  
18  
24  
31  
37  
43  
Green @ Full  
Proportional Red and Blue  
229  
100  
100  
50  
Red and Green @ Full, Blue @  
50%  
230  
231  
232  
100  
100  
100  
88  
76  
64  
62  
74  
86  
Red @ Full  
Proportional Green and Blue  
233  
100  
50  
100  
Red and Blue @ Full, Green @  
50%  
TFX-950CM User Manual  
17  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
234  
235  
236  
237  
238  
239  
240  
241  
242  
243  
244  
245  
246  
247  
248  
249  
250  
251  
88  
76  
64  
50  
44  
38  
32  
25  
19  
13  
7
12  
18  
24  
31  
37  
43  
49  
44  
38  
32  
25  
19  
13  
7
12  
18  
24  
30  
36  
42  
48  
62  
74  
86  
98  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
100  
Blue @ Full  
Proportional Red and Green  
252  
253  
254  
62  
74  
86  
100  
100  
100  
100  
100  
100  
Blue and Green @ Full  
Proportional Red  
255  
100  
100  
100  
Red,Green,Blue @ FULL  
(White)  
Maintenance  
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage  
and environment are contributing factors in determining frequency. As a general rule, fixtures should  
be cleaned at least twice a month. Dust build up reduces light output performance and can cause  
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off  
fixture before conducting maintenance.  
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust  
collected on external vents and internal components. Clean all glass when the fixture is cold with a  
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply  
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical  
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil  
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or  
becomes dirty, clean the lamps with an alcohol wipe.  
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to  
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:  
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the units  
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean  
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.  
TFX-950CM User Manual  
18  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Returns Procedure  
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.  
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products  
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the  
fixture. Be prepared to provide the model number, serial number and a brief description of the cause  
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate  
packaging is the customers responsibility. CHAUVET reserves the right to use its own discretion to  
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe  
method to use.  
Claims  
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be  
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and  
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim  
for items such as missing component/part, damage not related to shipping, and concealed damage,  
must be made within seven (7) days of receiving merchandise.  
TFX-950CM User Manual  
19  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Appendix  
General Troubleshooting  
Applies to  
Foggers  
& Snow  
Dimmers&  
Chaser  
Symptom  
Solution(s)  
Lights  
Controllers  
Auto shut off  
Check fan thermal switch reset  
Beam is very dim or  
not bright  
Clean optical system or replace lamp  
Check 220/110v switch for proper setting  
Breaker/Fuse keeps  
blowing  
Check total load placed on device  
Chase is too slow  
Check users manual for speed adjustment  
Device has no power  
Check for power on Mains.  
Check devices fuse. (internal and/or external)  
Fixture is not  
responding  
Check DMX Dip switch settings for correct  
addressing  
Check DMX cables  
Check polarity switch settings  
Fixture is on but there  
is no movement to the  
audio  
Make sure you have the correct audio mode on the  
control switches. If audio provided via ¼jack, make  
sure a live audio signal exists  
Adjust sound sensitivity knob  
Lamps cuts off  
sporadically  
Possible bad lamp or fixture is overheating.  
Lamp may be at end of its life.  
Light will not come on  
after power failure  
Some discharge lamps require a cooling off period  
before the electronics in the fixture can kick start it  
again, wait 5 to 10 minutes before powering up  
Loss of signal  
Use only DMX cables  
Install terminator  
Note: Keep DMX cables separated from power  
cables or black lights.  
Moves slow  
No flash  
Check 220/110v switch for proper setting  
Re-install bulb, may have shifted in shipping  
No laser output  
Bounce mirror motor may have shifted during  
shipping, readjust  
No light output  
Check slip ring & brushes for contact  
Install bulb  
Call service technician  
Relay will not work  
Check reset switch  
Check cable connections  
Remote does not work Make sure connector is firmly connected to device  
Stand alone mode  
All Chauvet lighting fixtures featuring stand-alone  
functions do not require additional settings, simply  
power the fixture and it will automatically enter into  
this mode  
TFX-950CM User Manual  
20  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Technical Specifications  
WEIGHT & DIMENSIONS  
Length...........................................................................................................................305 mm (12 in)  
Width...............................................................................................................................229 mm (9 in)  
Height .............................................................................................................................152 mm (6 in)  
Weight.........................................................................................................................5.9 Kg (13.2 lbs)  
POWER  
Switch-selectable power settings.................................................................115V 60 Hz or 230V 50 Hz  
European version............................................................................................................... 240V 50 Hz  
AC input.......................................................................................................... 3-prong IEC 60320 C14  
LAMPS  
3 x EHM (115V)............................................................................................................ 2,000 hr, 300W  
3 x EHM2 (230V) ......................................................................................................... 2,000 hr, 300W  
.
THERMAL  
Maximum ambient temperature......................................................................................... 40° (104° F)  
FUSE  
Main................................................................................................. 30mm Glass 10A 125V Fast Blow  
PCB ............................................................................................................ 20mm Glass 2A Fast Blow  
CONTROL & PROGRAMMING  
Data input ............................................................................................. locking 3-pin XLR male socket  
Data output ........................................................................................ locking 3-pin XLR female socket  
Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)  
Protocols.....................................................................................................................DMX-512 USITT  
DMX Channels.............................................................................................................................2 to 4  
ORDERING INFORMATION  
Stage Wash950............................................................................................................ TFX-950CM  
Stage WashController Pack......................................................................................... TFX-CONPK  
CA-32F Colormix foot Controller............................................................................................TFX-SWF  
Fuse 2A ........................................................................................................................ P170FUSE002  
Fuse 10A ...................................................................................................................... P170FUSE010  
TFX-950CM User Manual  
21  
Revision: 2006-01-20/16:37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Belshaw Brothers Oven BARO 2E User Manual
Black Decker Pressure Washer 598667 00 User Manual
Brother All in One Printer DCP J725DW User Manual
Brother Fax Machine FAX2580C 2480C User Manual
Bryan Boilers Boiler CFS 15 20 20D User Manual
Califone Music Pedal KMFT User Manual
Campbell Hausfeld Air Cleaner PA208503 User Manual
Chamberlain Home Security System CWV1000 User Manual
Christie Digital Systems Projector XENON CONSOLE User Manual
Cisco Systems IP Phone OL 11524 01 User Manual