Quick Reference Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
Operating modes:
9-channel: Pan, tilt, red, green, blue, color/macros, dimmer,
strobe, control
Features
13-channel: Pan, pan fine, tilt, tilt fine, pan/tilt speed, red,
green, blue, color/macros, dimmer, strobe, and
control
Pan: 540
Tilt: 270
RGB static color mixing with or without DMX control
Electronic strobe (1~20 Hz)
Electronic dimmer (0~100%)
High power setting
Remote product reset and vector speed channel
Auto programs
Sound activated programs
255-step fully customizable program
Recall auto or custom programs via control panel or DMX
Color temperature presets (3,200~10,000 K)
Color calibration
Fan speed control
3-pin DMX input and output connectors
LCD screen with password protection
The Q-Wash 260-LED is an RGB LED wash moving head with
multiple narrow beams. The product consists of a base and a moving
head on a yoke. The LEDs are inside ducts, which, along with
special optics, provide a very narrow beam angle.
Product
Description
LCD
Control Panel
Front Panel
Product Overview
Power Input
Fuse Holder
Power Switch
DMX In/Out
Rear Panel
Page 3 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
This product has an auto-ranging power supply that can work with
an input voltage range of 100~240 VAC, 50/60 Hz.
AC Power
Fuse 1. Wedge the tip of a flat head screwdriver into the slot of the fuse
Replacement
holder and pry the safety cap out of its housing. It will pull the
installed fuse with it.
2. Remove the blown fuse from its safety cap and replace it with a
fuse of the exact same type and rating (F 3.15 A, 250 V).
3. Insert the fuse holder back into its place, and reconnect power.
The Q-Wash 260-LED can work with a DMX controller using a
regular DMX serial connection.
DMX Linking
If you are not familiar with the DMX standard, please download the
DMX Primer document from www.chauvetlighting.com.
DMX Connection
The Q-Wash 260-LED uses a regular DMX data connection for
DMX personalities, BASIC, and ADVANCED.
Download the Q-Wash 260-LED User Manual and refer to the Setup
chapter to learn how to connect this product for DMX operation, and
the Operation chapter to learn in detail how to configure this product
for DMX operation.
Master/Slave
Connection
The Q-Wash 260-LED uses the DMX data connection for its
Master/Slave mode.
Download the Q-Wash 260-LED User Manual and refer to the Setup
chapter to learn how to connect this product for Master/Slave
operation, and the Operation chapter to learn in detail how to
configure this product for Master/Slave operation.
Before mounting this product, read the safety notes at the beginning
of this guide and on page 2 of the product’s User Manual. Then,
follow the mounting procedure indicated in the Setup chapter of the
User Manual.
Mounting
C clamps (not included)
Safety cable (included)
Mounting brackets (included)
Product
Mounting
Diagram
Overhead Mounting
Floor Standing
Page 4 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
Programming For details on how to program this product, please refer to the
product’s User Manual.
Control Panel
Description
Button Function
<MENU> Exits from the current menu or function
Enables the currently displayed menu or sets the
currently selected value into the selected function
<ENTER>
Navigates upwards through the menu list and
increases the numeric value when in a function
<UP>
Navigates downwards through the menu list and
decreases the numeric value when in a function
<DOWN>
After being prompted to enter the password, press:
Password
<UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>.
Start Address
To ensure full access to all channels in each DMX mode, the
highest recommended DMX addresses are as follows:
Mode
Address
Mode
Address
BASIC
504
ADVANCED
500
Editing Notes
When in EDIT and CALIB modes, <UP> and <DOWN> only
change the value of the selected option.
To move to the next option press <ENTER> repeatedly. Refer
to
the
Q-Wash 260-LED User Manual for more details.
Page 5 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
Menu Options
1st Level
Programming Levels
Description
Selects a starting DMX address
Resets the product’s custom settings
Select the fan’s operation mode.
ADDRESS
RESET
001~512
NO/YES
HIGH
NORMAL
LOW
AUTO
NOTE: Fixture’s controller will force the fan to High if the
product’s internal temperature becomes too high, despite any
manual or DMX setting
FANS
DMX512
AUTO1
AUTO2
CUSTOM
SOUND1
SOUND2
SLAVE
TEST
Selects DMX running mode
Selects the first automatic program
Selects the second automatic program
Selects the user customizable program
Selects the first sound program
Selects the second sound program
Selects the Slave running mode
RUN
INTRO
Starts the product’s test sequence
BASIC
Selects the 9-channel DMX mode
CHANNELS
ADVANCED Selects the 12-channel DMX mode
60 CLOSE
BRIGHT
NO/YES
Turns off the display after 60 seconds
Keeps the display on
Activates/deactivates the control panel password
DISPLAY
KEYLOCK
DIMMER
DIMMER 4~1 Slow (DIM 4) to fast (DIM1) dimmer curves
DIMMER 0
EDITION
Linear dimmer
Shows the version of the installed S/W
Defines the pan direction
Defines the tilt direction
Defines the direction of the dimmer fader
Activates the changes
INFO
PAN
TILT
DIMMER
USE
NORMAL/
REVERSE
INVERT
RANGE
NO/YES
P/START
P/FINISH
T/START
T/FINISH
USE
Sets the pan start point (restricted range)
Sets the pan end point (restricted range)
Sets the tilt start point (restricted range)
Sets the tilt end point (restricted range)
Activates the changes
000~255
NO/YES
DMX
SYSTEM
Activates the move-in black delay (3 s)
The DMX controller can reset the product
The control panel can reset the product
LEDs illuminate at normal or high intensity
NOTE: The product will return to Normal if the internal
temperature becomes too high
BLACKD
RESET
NORMAL/
HIGH
POWER
UC
RGBTOW
OFF
DMX
SYSTEM
White output matches that of older products
White output set by RGB-W
SPECIAL
COLOR
FAN
White output defined by RGBW faders
The DMX controller can set the fan speed
The control panel can reset the fan speed
In case of lost DMX signal, the product will remain in its current
state
SAVE
BLAK
DMXERROR
In case of lost DMX signal, the product will blackout
STEP
PAN
Selects the program step
Selects the pan position
Selects the tilt position
Selects the pan/tilt speed
EDIT
000~255
TILT
SPEED
1st Level
Programming Levels
Description
RED
GREEN
BLUE
Combines red, green, blue, and white to obtain a custom color
DIMMER
STROBE
DIMSPEED
TIME
000~255
Selects the dimmer value
EDIT (Cont.)
EXTRA
Selects the strobe frequency and mode
Selects the dimmer speed
Selects the step duration
USE
NO/YES
****
Activates the changes
PASSWORD
Opens the Extra menu (see below)
Page 6 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
Extra Menu
1st Level
2nd Level
3rd Level
4th Level
Description
RED
GREEN
BLUE
RED
3200 K
000~255
Sets color temperature for Macro > White 1
3400 K
4200 K
4900 K
5600 K
5900 K
6500 K
7200 K
8000 K
8500 K
10000 K
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
000~255
000~255
000~255
000~255
000~255
000~255
000~255
000~255
000~255
000~255
Sets color temperature for Macro > White 2
Sets color temperature for Macro > White 3
Sets color temperature for Macro > White 4
Sets color temperature for Macro > White 5
Sets color temperature for Macro > White 6
Sets color temperature for Macro > White 7
Sets color temperature for Macro > White 8
Sets color temperature for Macro > White 9
Sets color temperature for Macro > White 10
Sets color temperature for Macro > White 11
CALIB
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
NO/YES
Sets color temperature for SPECIAL > COLOR >
RGBTOW
RGB-W
000~255
DEFAULT
DEFAULT
N/A
Defaults the product to factory settings
Page 7 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
DMX Values
Channel Function
Value
000 255 0~540º
000 255 0~270º
000 255
000 255
000 255
Percent/Setting
BASIC
1
2
3
4
5
Pan
Tilt
Red
Green
Blue
0~100%
0~100%
0~100%
000 005 No function
006 010 High power
011 030 R: 100% G: Up
B: 0%
031 050 R: Down G: 100% B: 0%
051 070 R: 0%
071 090 R: 0%
091 110 R: Up
111 130 R: 100% G: 0%
131 150 R: 100% G: Up
G: 100% B: Up
G: Down B: 100%
G: 0%
B: 100%
B: Down
B: Up
151 170 R: Down G: Down B: 100%
171 200 R: 100% G: 100% B: 100%
201 205 White 1: 3200 K
206 210 White 2: 3400 K
211 215 White 3: 4200 K
216 220 White 4: 4900 K
221 225 White 5: 5600 K
226 230 White 6: 5900 K
231 235 White 7: 6500 K
236 240 White 8: 7200 K
241 245 White 9: 8000 K
246 250 White 10: 8500 K
251 255 White 11: 10,000 K
000 255 0~100%
Power and Color
Macro
6
7
8
Dimmer
Strobe
000 009 No function
010 255 01~20 Hz
000 019 No function
020 039 Pan/tilt black activation
040 059 Pan/tilt black deactivation
060 079 Automatic fan speed
080 099 Slow fan speed
100 119 Normal fan speed
120 139 High fan speed
9
Control
140 149 Auto program 1 (3 s activation delay)
150 159 Auto program 2 (3 s activation delay)
160 169 Test (3 s activation delay)
170 179 Custom program (3 s activation delay)
180 199 No function
200 219 Reset (3 s activation delay)
220 255 No function
Page 8 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
Channel Function
Value
000 255 0~540º
000 255 Fine movement control
000 255 0~270º
000 255 Fine movement control
000 255 Fast~Slow
000 255
000 255
000 255
Percent/Setting
ADVANCED
1
2
3
4
5
6
7
8
Pan
Pan Fine
Tilt
Tilt Fine
Pan/Tilt Speed
Red
Green
Blue
0~100%
0~100%
0~100%
000 005 No function
006 010 High power
011 030 R: 100% G: Up
B: 0%
031 050 R: Down G: 100% B: 0%
051 070 R: 0%
071 090 R: 0%
091 110 R: Up
111 130 R: 100% G: 0%
131 150 R: 100% G: Up
G: 100% B: Up
G: Down B: 100%
G: 0%
B: 100%
B: Down
B: Up
151 170 R: Down G: Down B: 100%
171 200 R: 100% G: 100% B: 100%
201 205 White 1: 3200 K
206 210 White 2: 3400 K
211 215 White 3: 4200 K
216 220 White 4: 4900 K
221 225 White 5: 5600 K
226 230 White 6: 5900 K
231 235 White 7: 6500 K
236 240 White 8: 7200 K
241 245 White 9: 8000 K
246 250 White 10: 8500 K
251 255 White 11: 10,000 K
000 255 0~100%
Power and Color
Macro
9
10
11
Dimmer
Strobe
000 009 No function
010 255 01~20 Hz
000 019 No function
020 039 Pan/tilt black activation
040 059 Pan/tilt black deactivation
060 079 Automatic fan speed
080 099 Slow fan speed
100 119 Normal fan speed
120 139 High fan speed
12
Control
140 149 Auto program 1 (3 s activation delay)
150 159 Auto program 2 (3 s activation delay)
160 169 Test (3 s activation delay)
170 179 Custom program (3 s activation delay)
180 199 No function
200 219 Reset (3 s activation delay)
220 255 No function
Page 9 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-Wash 260-LED QRG
World Headquarters
CHAUVET®
General Information
United Kingdom and Ireland
CHAUVET® Europe Ltd.
General Information
Address:
Contact Us
Address:
5200 NW 108th Avenue
Unit 1C
Sunrise, FL 33351
(954) 929-1115
(954) 929-5560
(800) 762-1084
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice:
Fax:
Toll free:
Voice:
Fax:
+44 (0)1773 511115
+44 (0)1773 511110
Technical Support
Technical Support
Voice:
Fax:
(954) 929-1115 (Press 4)
(954) 756-8015
Email:
Email:
World Wide Web
World Wide Web
Q-Wash 260-LED QRG – Rev. 05
© Copyright 2011 CHAUVET®
All rights reserved
Printed in the P. R. C.
Page 10 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|