®
Model LSIA & LSIS
Wireless Portable Intercom - Extreme Range
Overview
Channel Select Button: Press the
Channel Select button to set
intercom to one of four secure
channels or the paging channel.
The default channel for the
The Intercom has up to a 1000' range and allows
multiple simultaneous conversations, using a
900 Mhz secure digital radio link. The intercoms form
an exclusive network and respond only to other
intercoms in the network.
intercom is the paging channel
where all four channel lights are lit. An intercom on a
channel can only hear an intercom on the same
channel or on the paging channel.
Carton Inventory
Battery: The AA Alkaline batteries (not provided) will
last up to a year depending on use (Lithium batteries
recommended for colder
environments). When batteries are
low intercom will emit two beeps
every ten minutes.
Rubber Pads
(2 in Model LSIS)
Intercom (2 in Model LSIS)
An AC Adapter (not provided) can
also be used to power the intercom.
In this case, both the power and
OPTIONAL
channel lights will remain on.
Operation & Features
Conference Mode: Conference Mode allows multiple
intercoms to participate in a conversation compared
to Normal Mode in which only two intercoms can
communicate. All intercoms must be set to the same
channel or the paging channel to be in
Channel Lights
Power Light
Talk Button
Active Light
Monitor Button
Conference Mode. To put intercom in
Speaker
Conference Mode set Dipswitch #2 to UP
position.
1
2
Channel
Select
Button
Volume DOWN
Button
Monitor Mode: Monitor Mode is
used to monitor the noise in a
Volume UP
Button
specific room. Place the intercom in
the room that is to be monitored
and press the Monitor button until a
tone is heard. The Active Light will
be lit while the intercom is in Monitor
Dipswitch #1
Dipswitch #2
AC Adapter
Learn Button
On/Off: To turn intercom ON, press Talk button.To
turn intercom OFF, hold down the Volume DOWN
button for 5 seconds.
Mode. Any other networked intercom can listen to
that room. If a specific channel is selected for Monitor
Mode then only other intercoms on that channel or on
the paging channel can listen. Press the Monitor
button again to exit Monitor Mode. A tone will be
heard indicating Monitor Mode is no longer active.
Talk Button: To talk, hold down the
Talk button. All intercoms in the
network that are on the same
channel will receive the signal.
Release the Talk button when done
talking and within 10-15 seconds
press and hold the Talk button of a different intercom
to make a secure channel between the two. Once the
channel is made the other intercoms in the network
cannot hear the conversation.
Voice Activation Mode (VOX): Voice Activation
Mode (VOX) allows a call to be answered without
pressing the Talk button. Once a call is heard on an
intercom which has been set to VOX, a response can
be given by speaking loudly into the intercom. There
will be a slight delay when VOX is first activated by a
voice, but will continue to transmit audio until
Volume: Pressing the Volume DOWN button will
lower the volume and pressing the Volume UP button
will increase the volume.
the speaking stops. To put intercom into VOX,
place Dipswitch #1 to the UP position.
1
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Intercom does not function.
Need to clear intercom’s memory.
Check batteries in intercom. If using an AC Adapter
ensure that it is plugged in.
Ensure intercom is connected to a network.
See Programming Intercom.
Ensure that intercoms are on the same channel. See
Operation & Features.
Press and hold Learn button, an initial beep will be
heard. Continue to hold until a second beep is heard
(about 15 seconds). Ensure other intercoms are not
activated during this time. Intercoms in the network that
are on will signal during the clearing process. Once
memory is clear the intercom can be programmed to a
new network.
Intercom is not getting expected transmission
range.
Keep antenna vertical. Keep intercom away from
trees, metal objects and electrical wiring. Cell phones,
cordless phones, or other radio devices may also
limit range.
Static and feedback is heard in intercom.
The intercoms are too close to each other. A cordless
phone, cell phone, or other radio devices can also
cause static.
Intercom is sending audio while no buttons are
pressed.
Intercom beeps every ten minutes.
The battery is low in the intercom. Replace with AA
Alkaline batteries or operate it with AC Adapter (not
provided). A 9-12 volt, 500mA AC Adapter may be
used (center positive polarity on the round plug).
The sending intercom is set to Monitoring Mode or Voice
Activation Mode and will activate when sound is heard.
It can be taken out of Monitoring Mode by pressing the
Talk button. It can be taken out of Voice Activation Mode
by setting Dipswitch #1 to DOWN position.
See Operation & Features.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
www.chamberlain-DIY.com
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
© 2008, The Chamberlain Group Inc.
All Rights Reserved
114A3576
Download from Www.Somanuals.com. All Manuals Search And Download.
|