®
Models PIRV400R
Wireless Pedestrian & Vehicle Sensor with Voice
AOSV
Wireless Office Alert Add-On Sensor
Overview
The PIR Motion Sensor only works with
Chamberlain's Wireless Pedestrian & Vehicle Alert
with Voice (Model RWV400R) and Office Alert
(Model CWV1000). The PIR Motion Sensor can be
used to monitor motion up to 30' away and can
transmit a signal up to 1000' away from the Base
Station (not included). The Passive Infra-Red sensor
detects movement of people and vehicles, while
allowing small animals to pass through undetected.
The PIR Motion Sensor has a built-in microphone and
speaker that allows for communication between the
Base Station and the Sensor. When the PIR Motion
Sensor detects movement a signal is sent to the base
station which alerts the homeowner with sounds and
lights. The Alert can also remotely control a low
voltage electrical device near the PIR Motion Sensor
like a light or a camera (See Advanced Features).
To prevent possible SERIOUS INJURY or DEATH from
electrocution, outputs are suitable ONLY for controlling low
voltage devices, 24V max, ac or dc.
Intercom Feature: When PIR Motion Sensor has
detected motion, the Base Station will allow you to
listen through the PIR Motion Sensor for 10 seconds.
If you wish to talk to the person on the other end,
hold down the Talk button and speak, releasing it to
hear.
Volume: Pressing the Volume button repeatedly will
cycle through volume levels.
Mute: To temporarily mute Base Station, hold the
Volume and Talk buttons down for three seconds.
The Base Station will reactivate after one hour, or by
pressing the Talk button.
Carton Inventory
Remote Button: If there is an accessory device
connected to the relay on the PIR Motion Sensor, it
can be activated by pressing the Remote button
within 30 seconds of the signal from the alert buzzer.
Swivel Bushing
Switch #1:
OFF
ON
Buzzer Off
Buzzer On (Default)
Mounting Plate
Passive Infra-Red (PIR)
Motion Sensor
OFF
ON
1
2
Switch #2:
OFF
ON
Long Buzz
Short Buzz (Default)
Operation & Features
Battery: The AA Alkaline batteries (not provided) will
last up to 2 years depending on use (Lithium batteries
recommended for colder environments). If PIR Motion
Sensor batteries are low Base Station will emit three
high-pitch beeps every ten minutes. If Base Station
batteries are low it will emit two high-pitch beeps.
Base Station
(not provided)
PIR Motion
Sensor
PIR Sensor/Test Light
Volume Button
Talk
(Power - On)
Clear Memory: Press and hold the Learn button on
the Base Station until 3 beeps are heard. If the PIR
Motion Sensor signals while Learn button is pressed,
repeat the procedure.
Relay Output
Contacts
Remote
Activation
Button
AC Adapter
Learn
Button
Switch #1: Mute
Switch #2: Tone
Programming Additional PIR Motion Sensors:
Each Base Station can learn the code of up to 8 PIR
Motion Sensors, responding with multiple buzzes. To
program additional PIR Motion Sensors see Step 6.
Speaker
On/Off: To turn Base Station OFF hold down the
Volume button until a beep is heard and light goes
out. To turn Base Station ON press the Talk button.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Features
Troubleshooting
Both the PIR Motion Sensor and Base Station have
relays which can activate other electrical devices. The
accessory device will need a separate power supply.
NOTE: Output switching capacity is low voltage (24V
max, ac or dc).
The Alert does not function.
Check batteries in PIR Motion Sensor. Ensure Base
Station has power. Ensure PIR Motion Sensor is
programmed to Base Station.
The Alert is not getting expected transmission
range.
Ensure Base Station antenna is vertical and keep PIR
Motion Sensor away from trees and metal objects.
Ensure Base Station is in clearest possible range of
PIR Motion Sensor. The less objects between
devices, the longer the range.
Base Station: The relays can be
used to activate louder alarm bells,
lights, cameras, or other accessories.
PIR Motion Sensor: The relays will
only activate when the remote button
is pressed on the Base Station. To
prevent access to these relays flush
mount the PIR Motion Sensor.
Base Station is not very loud.
Adjust the volume of speaker. An accessory such as
a low voltage bell, buzzer or light can be attached to
the relay switch. The accessory device will need
separate power supply.
NOTE: Output switching capacity is low voltage
(24V max, ac or dc).
Static and feedback is heard in Base Station.
PIR Motion Sensor is too close to the Base Station.
The PIR Motion Sensor is detecting motion only
part of the time.
To detect cars, it is best to mount PIR Motion Sensor
at height of car’s motor and have it between ten and
twenty feet from the road. Swivel sensor as needed.
The Alert is giving false alarms.
Check for moving tree branches or insects in sensor
window. PIR sensor can also be triggered by light
shining directly in sensor window, such as reflected
sunlight, or motion in front of a light source.
Base Station beeps every ten minutes.
If there are two beeps the battery is low in the Base
Station. Replace with AA Alkaline batteries or operate
it with AC Adapter. If there are three beeps the battery
is low in the PIR Motion Sensor. Replace with AA
Alkaline batteries.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
© 2008, The Chamberlain Group Inc.
All Rights Reserved
114A3516C
Download from Www.Somanuals.com. All Manuals Search And Download.
|