B3
ESTATE SERIES
MASTER / SLAVE SYSTEMS
MODEL SL 1000-B3, SW 2000-B3 & BG 3000-B3
SLIDE, SWING, AND BARRIER GATE OPERATORS
MODEL SL 1000-B3
MODEL BG 3000-B3
MODEL SW 2000-B3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF FIGURES
Figure 1. Master/Slave Gate Configurations........................................................................................................3
Figure 2. Typical Bi-Parting Gate Installation. .....................................................................................................4
Figure 3. Typical Bi-Parting Latch Gate Installation.............................................................................................5
Figure 4. Typical Trap Gate Installation...............................................................................................................6
Figure 5. Typical Tandem Gate Installation.........................................................................................................8
Figure 6. Biparting Slide Gate Photo-Sensor Layout.........................................................................................10
Figure 7. Biparting Swing Gates Photo-Sensor Layout. ....................................................................................11
Figure 8. Biparting Barrier Gates Photo-Sensor Layout. ...................................................................................12
Figure 9. Control Board Wiring. .........................................................................................................................13
Figure 10. Master Slave Connection and Switch S1 Location...........................................................................15
Figure 11. Switch S1 Settings for Master/Slave Systems..................................................................................16
Figure 12. Bi-Part, Bi-Directional Gate System. ................................................................................................17
Figure 13. Bi-Part, Uni-Directional Gate System (Swing gate, if used, opens in)..............................................17
Figure 14. Bi-Part, Uni-Directional Gate System (Swing gate opens out). ........................................................18
Figure 15. Bi-Part, Bi-Directional Gate System. ................................................................................................18
Figure 16. Bi-Part Latch, Uni-Direction Gate System (Swing gate, if used, opens in).......................................19
Figure 17. Bi-Part Latch, Uni-Directional Gate System (Swing gate opens out). ..............................................19
Figure 19. Bi-Directional Trap Gate System (Swing gate opens out)................................................................21
Figure 20. Uni-Directional Trap Gate System (internal Swing gate, if used, opens in)......................................22
Figure 21. Uni-Directional Trap Gate System (internal Swing gate opens out).................................................23
Figure 22. Uni-Directional Trap Gate System (external Swing gate, if used, opens in).....................................24
Figure 23. Uni-Directional Trap Gate System (external Swing gate opens out)................................................25
Figure 24. Bi-Directional Tandem Gate System (Swing gate, if used, opens in)...............................................26
Figure 26. Uni-Directional Tandem Gate System (Swing gate, if used, opens in).............................................28
Figure 27. Uni-Directional Tandem Gate System (Swing gate opens out)........................................................29
Rev E
Doc 01-20201
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY SUMMARY
It is important for everyone involved in the installation and operation of the LiftMaster models SL 1000,
SW 2000, and BG 3000 Master/Slave systems to read the following warnings.
WARNING!
• A vehicle gate is a large, heavy object that is moved by an electric motor. A moving gate can
cause serious injury or death! The safety and well-being of others depends on the installation
of a safe system.
• READ AND FOLLOW ALL INSTRUCTIONS. Improper installation of a gate operator can result
in a dangerous system. SAVE THESE INSTRUCTIONS
• The entrance is for vehicles only. Pedestrians must use separate entrance.
• Gate operators can present serious hazards to persons in the immediate area when not
controlled in a safe manner. Choose one or more controls which together will allow complete
control of the gate. Most importantly, the gate must be able to be stopped at all times in case
of emergency, and the emergency control should be conveniently located, clearly marked, and
visible.
• All controls must be kept out of reach of small children. Serious injury or death can result
from children playing with the controls.
• Always keep people and objects away from the gate. NO ONE SHOULD CROSS THE PATH OF
THE MOVING GATE.
• All controls should be located so the person operating them can see the full area of gate
movement.
• Use the emergency release only when the gate is not moving.
• KEEP GATES PROPERLY MAINTAINED. Read the Installation and Operation manual. Have a
qualified person make repairs to gate hardware.
• Test the gate operator safety features monthly. The gate MUST reverse on contact with a rigid
object or stop when an object activates the non-contact sensors.
• After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and
retest the gate operator properly can increase the risk of damage, injury or death.
• Gate operators and associated control equipment should be installed by qualified
professional installers who should observe the following safe installation procedures:
1. Power should always be disconnected whenever installing, wiring, or servicing a gate
operator. Moving chains and belts in gate operators can catch clothing or fingers and
cause severe injury.
2. Installation of wiring should comply with all local building and electrical codes.
3. All manual gate locks should be disabled to avoid damage to the gate or gate operator
should the lock become engaged after the operator is installed.
4. All operator controls and safety equipment should be tested at the conclusion of
installation to be sure they are functioning properly.
5. The operation of the gate controls and safety equipment should be reviewed with the
owner and/or end user of the automated gate system. They should also be informed of the
need to maintain control and safety equipment on a regular basis. Safety equipment
should be checked monthly to ensure it is working properly. All installation manuals and
safety information should be left with the owner.
6. Moving gates have pinch points and entrapment zones which can be extremely dangerous
to pedestrians, especially small children.
Rev E
Doc 01-20201
1 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC INSTALLATION HINTS AND RULES
READ THIS SECTION CAREFULLY BEFORE BEGINNING YOUR INSTALLATION
1. UNDERSTAND THE SYSTEM AND INSTALLATION SITE THOROUGHLY. The B3 series are
flexible and reliable gate operator systems, but the quality of service depends directly on the quality
of installation. Please read these instructions and the Installation and Operation instructions for
each gate operator carefully. Study the applicable diagrams before planning your installation. In
particular, understand any site characteristics that may affect the system installation.
WARNING
2. INSTALL PERMANENT WIRING. U.L. specifications require the B3 Series Master/Slave systems
to be permanently wired. Refer to your local wiring code for specific information.
WARNING: Damage caused by faulty wiring is not covered by warranty.
3. GROUND THE SYSTEM. The system contains parts which may be damaged by static discharge.
A proper earth ground connected to the housing will significantly reduce the chances of damage or
improper operation. The shielding in the cables specified for all remote sensors and controls should
also be connected to earth ground at the controller end of the cable only.
To be effective, the ground connection must be made by running 12 AWG copper wire to a good
ground point (e.g., an electrical panel, a metallic cold water pipe that runs into the earth, or a
grounding rod at least 10 feet in length that is driven into the earth) within 12 feet of the system.
Even if you have a good ground, you should try to discharge any static before handling the circuit
boards.
WARNING: Damage caused by static discharge and lightning is not covered by warranty.
4. PROVIDE POWER FROM A DEDICATED SOURCE. The outlet into which you connect the Gate
Operators should be wired to its own circuit breaker. This will reduce the line noise introduced into
system power and minimize the risk of having other equipment interrupt system operation. In a
Master/Slave system, Master and Slave must each have separate circuits.
5. DO NOT OVERLOAD THE TERMINAL BLOCKS. The operator’s terminal blocks are removable
and the pins are soldered into the boards. To connect the wires, remove the “head” from the
correct terminals and open the screws. Insert the wire into the correct opening on the front and
tighten the screw until the wire is held firmly. When you have made all connections for a given
“head”, plug it back onto the pins designated for that terminal block.
Stranded wire must be between 16 and 24 AWG. Solid wire must be between 18 and 24 AWG.
This is the total thickness measurement so, if you are putting two wires in, the combined thickness
must fall within this range. NEVER try to insert more than two wires per terminal.
6. ENSURE GOOD CONNECTIONS. A light tug on the wire will tell you if the connection is secure.
When reconnecting system components, make sure all pins are straight on chips, connectors, and
terminal block heads.
7. READ MARKINGS CAREFULLY. The connection points are marked on the boards clearly.
Before making any connection, be sure to read the marking and check it against the corresponding
figure in these instructions so that you understand the connection you are making.
8. TRAIN YOUR CUSTOMERS THOROUGHLY. Although customer responsibility is limited to proper
installation, the quality of service is determined by the care of system set up. Ensure that the
customer has a copy of this manual to guide them. It will save you and them lots of inconvenience
and aggravation later.
Rev E
Doc 01-20201
2 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
PART 1
MASTER/SLAVE OPERATION
A. WHAT IS MASTER/SLAVE OPERATION?
The easy way to understand master/slave operation is by the computer terms “smart” and “dumb”.
•
•
“Smart” machines are controlled by a computer or dedicated microprocessor, such as microwave
ovens and new-style washing machines.
“Dumb” machines are controlled by simple electronic or physical mechanisms, like old-style washing
machines with their cams and timers.
When your installation requires using two gates together, they can be controlled either by the “dumb”
method of wiring them in parallel and using limit cams and reclose timers for control (see the Installation
and Operation manual for the individual gate operator), or the “smart” method of enabling the
Master/Slave programming built into the gate operators.
LiftMaster gate operators are capable of handling any gate combination you’re likely to need, and we
strongly recommend using the “smart” method for the following reasons:
1. Synchronization: Gate actions (opening, closing, etc.) are synchronized in Master/Slave
operation.
2. Added safety: A fault in one unit affects both units, providing added safety to the system.
3. Reduced wiring: Inputs (radio, exit loops, etc.) need be wired to only one unit in some
Master/Slave configurations.
4. Simplified gate setting: Gate controls (Anti-Tailgate, Reclose Timer, etc.) only need to be
set in one unit in some Master/Slave configurations.
Let’s take a quick look at some Master/Slave gate configurations, cover the wiring and setup procedures,
then go into the details of each type to help plan your installation.
B. MASTER/SLAVE GATE CONFIGURATIONS
LiftMaster models SL 1000-B3 (slide gate), SW 2000-B3 (swing gate), and BG 3000-B3 (barrier gate)
can be teamed as Master/Slave systems in the following configurations:
Figure 1. Master/Slave Gate Configurations.
•
•
In the Master/Slave configuration, one Master unit controls one Slave unit.
Master and Slave units communicate at 9600 baud via a 4-wire interconnection cable.
Rev E
Doc 01-20201
3 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
C. MASTER/SLAVE INSTALLATION DETAILS
1. BI-PARTING GATE DETAILS
The simple Bi-Parting Gate is typically used in low traffic residential sites due to its ease of use. The Bi-
Parting configuration can consist of any combination of models SL 1000-B3 (slide gate),
SW 2000-B3 (swing gate), and BG 3000-B3 (barrier gate).
ADDITIONAL
COMPLEX
INPUTS:
Radio
Cycle
Interrupt Bar
Photo-Sensors
Fire
Exit Loop
MagLock
Manual Inputs
Inside Interrupt
Loop
Gate
Operator
Master
Gate
Operator
Slave
Shadow Loop
(swing gates only)
Master/Slave Cable
Slave Gate
Master Gate
Fence
Fence
Outside Interrupt
Loop
Connect MagLock to one unit only.
STREET
1384F2
Figure 2. Typical Bi-Parting Gate Installation.
HOW IT WORKS:
•
•
The gates in a Bi-Parting configuration are mirror images of each other and act identically.
A Fault in one unit affects both units (see Troubleshooting/Maintenance for Fault List in the
Installation and Operation manual for the individual gate).
•
A Continuous open input in either unit opens the gates and holds them open.
There are 3 different ways to close the gates (entering or exiting):
1. Reclose Timer: When the Reclose Timer expires, gates close automatically.
2. ATG (Anti-Tailgate) and Interrupt Loop: With ATG ON, clearing the Inside Interrupt Loop closes the
gates. NOTE: For safety reasons, ATG does not function with gate type SWING or LINEAR.
3. Alternate Action: With ATG and TIMER OFF, a Radio or CYCLE command will close fully-open
gates.
INPUT CONNECTIONS: Refer to Part 2, Master/Slave Layout and Wiring, for more details.
•
Inputs can be connected to either gate.
Rev E
Doc 01-20201
4 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
2. BI-PARTING LATCH GATE DETAILS
The Bi-Parting Latch Gate is typically used in low traffic residential sites due to ease of use and added
security of magnetic locking. The Bi-Parting Latch configuration can consist of any combination of
models SL 1000-B3 (slide gate), SW 2000-B3 (swing gate), and BG 3000-B3 (barrier gate).
ADDITIONAL
INPUTS:
Radio
COMPLEX
Cycle
Interrupt Bar
Photo Sensors
Fire
Exit Loop
MagLock
Manual Inputs
Inside Interrupt
Loop
Gate
Operator
Master
Gate
Operator
Slave
Shadow Loop
Master/Slave Cable
Fence
Fence
Outside Interrupt
Loop
Connect MagLock to one unit only.
STREET
1384F3
Figure 3. Typical Bi-Parting Latch Gate Installation.
HOW IT WORKS:
•
The Master moves first during opening and the Slave first during closing, with a 2 second delay
between them to prevent gate intercollision and to ensure proper latching. When the gates are fully
closed, the outer edge of the Master gate rests on the outer edge of the Slave gate.
A fault in one unit affects both units (see Troubleshooting/Maintenance for Fault List in the
Installation and Operation manual for the individual gate operator).
•
•
A continuous open input in either unit opens the gates and holds them open.
There are 3 different ways to close the gates (entering or exiting):
1. Reclose Timer: When the Reclose Timer expires, gates close automatically.
2. ATG (Anti-Tailgate) and Interrupt Loop: With ATG ON, clearing the Inside Interrupt Loop closes the
gates. NOTE: For safety reasons, ATG does not function with gate type SWING or LINEAR.
3. Alternate Action: With ATG and TIMER OFF, a RADIO or CYCLE command will close the fully
open gates.
INPUT CONNECTIONS: Refer to Part 2, Master/Slave Layout and Wiring, for more details.
•
Inputs can be connected to either unit.
Rev E
Doc 01-20201
5 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
3. TRAP GATE DETAILS
The Trap gate is typically used in secured sites for screening incoming and/or outgoing traffic. In the
Trap configuration, only one gate opens at a time, “trapping” the vehicle between gates. Due to ease of
use, Slide Gates are the most popular for the Trap configuration. The Trap configuration can consist of
any LiftMaster model for the Master, and a model SL 1000-B3 (slide gate), or BG 3000-B3 (barrier gate)
for the Slave. NOTE: The SW 2000-B3 (swing gate) may not be used for the Slave gate.
ADDITIONAL
INPUTS:
COMPLEX
Radio
Cycle
Interrupt Bar
Photo-Sensors
Fire
MagLock
Manual Inputs
Inside Interrupt
Loop
Gate
Operator
Master
Shadow Loop
(swing gate only)
Master/
Slave
Cable
Outside Interrupt
Loop
ADDTIONAL
INPUTS:
Radio
Cycle
Interrupt Bar
Photo-Sensors
Fire
MagLock
Manual Inputs
Inside Interrupt
Loop
Gate
Operator
Slave
Outside Interrupt
Loop
STREET
1384F4
Figure 4. Typical Trap Gate Installation.
HOW IT WORKS
•
In normal operation, one gate must completely close before the other opens, so only one gate is
open at a time. As soon as one gate closes, the second gate automatically opens. If the second
gate does not open within 10 seconds, the first gate reopens to let the vehicle exit the trap area.
•
ATG (Anti-Tailgate) is always active for both Master and Slave units. Each gate closes as soon as its
Inside Interrupt loop clears.
•
•
•
Faults and Manual Input Commands in one unit affect both units.
A continuous FIRE or Manual OPEN input in either unit opens the gates and holds them open.
If a vehicle stalls between the gates and they close, they can be opened by a CYCLE or RADIO
command, or by driving over the Slave unit Inside Interrupt Loop (gate to SLIDE or BARRIER only).
Rev E
Doc 01-20201
6 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
There are 2 different ways to close the gate (entering or exiting):
1. Reclose Timer: When the Reclose Timer expires, gate closes automatically (Master or Slave).
2. Interrupt Loop: clearing the Inside Interrupt Loops cause the gates to close (Master or Slave).
NOTE: To ensure gate closure, set Reclose Timer = ON in both Master and Slave units.
INPUT CONNECTIONS: Refer to Part 2 Master/Slave Layout and Wiring, for more details
•
•
Master and Slave units require their own separate inputs.
If Radio inputs are used in both units, each requires its own transmitter and entry code.
Rev E
Doc 01-20201
7 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TANDEM GATE DETAILS
The Tandem gate is typically used in high traffic situations where some control of incoming and/or
outgoing traffic is required. The outside gate (slave) is usually a less expensive fast moving
barrier gate (or light slide gate) which protects the more expensive and less mobile Slide or Swing
inside gate (master). The outside gate does this by stopping the vehicle until the inside gate is
completely open. The Tandem configuration can consist of any LiftMaster model for Master, and
a model SL 1000-B3 (slide gate), or BG 3000-B3 (barrier gate) for Slave. NOTE: The SW 2000-
B3 (swing gate) may not be used for Slave.
ADDTIONAL
INPUTS:
Radio
COMPLEX
Cycle
Interrupt Bar
Photo-Sensors
Fire
Exit Loop
MagLock
Manual Inputs
Inside Interrupt
Loop
Gate
Operator
Master
Shadow Loop
(swing gate only)
Master/
Slave
Cable
Outside Interrupt
Loop
ADDITIONAL
INPUTS:
Radio
Cycle
Interrupt Bar
Photo-Sensors
Fire
MagLock
Manual Inputs
Inside Interrupt
Loop
Gate
Operator
Slave
Outside Interrupt
Loop
STREET
1384F5
Figure 5. Typical Tandem Gate Installation.
Rev E
Doc 01-20201
8 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW IT WORKS:
•
When a vehicle is entering or exiting, the inside Master gate opens first. When the Master is
completely open, the outside Slave gate opens, allowing the vehicle to enter or exit.
•
The Master unit Reclose Timer (if enabled) does not start counting down until the Slave gate is fully
closed. Since ATG is not allowed in the Master unit, if the Reclose Timer is not enabled, the Master
gate will remain open.
•
•
•
During high traffic hours, the slower-moving Master gate can be latched open by a continuous
Manual Open input, leaving the faster moving Slave gate to control entering and exiting traffic.
If a vehicle stalls between the gates and they close, they can be opened by a CYCLE or RADIO
command, or by driving over the Slave unit Inside Interrupt Loop (SLIDE ACTION=ON only).
A fault in one unit affects both units (For Fault List, see Troubleshooting/Maintenance in Installation
and Operation manual for individual gate operator).
•
•
A continuous FIRE input in either unit opens both gates and holds them open.
A continuous Manual OPEN in the Slave unit opens both gates and holds them open.
There are 2 different ways to close the gate after entering or exiting:
1. Reclose Timer: When the Reclose Timer expires, the gates close automatically (Slave or Master).
2. ATG (Anti-Tailgate) and Interrupt Loop: When ATG is ON, clearing the Inside or Outside Interrupt
Loop causes the Slave gate to close.
INPUT CONNECTIONS: Refer to Part 2 Master/Slave Layout and Wiring, for more details.
•
Barrier Gate: If the installation requires only one Loop Sensor for the Slave gate:
1. Install the Loop Sensor under the barrier gate arm.
2. Connect to the Outside Interrupt Loop input.
Rev E
Doc 01-20201
9 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
PART 2
MASTER/SLAVE LAYOUTS AND WIRING
A. PHOTO-SENSOR INSTALLATION FOR BIPARTING GATE CONFIGURATION
BIPARTING SLIDE GATES
Figure 6. Biparting Slide Gate Photo-Sensor Layout.
WARNING
Buy only UL-approved photo-sensors made for use with vehicular gate
operators or system. Otherwise, safe gate operation may be compromised.
IMPORTANT NOTE: The installation shown in Figure 6 above is a suggested layout using emitters
and receivers. Any UL-approved photo-sensors are acceptable, but they must cover the entire area
of gate travel to be effective.
Install photo-sensors in three Coverage Areas as shown in Figure 6.
1. Coverage Area A - Inside-Open Coverage:
Install two photo-sensors: Inside the fence line, from the gate operators to the gate fully open
positions.
2. Coverage Area B - Inside-Closed Coverage:
Install one photo-sensor: Inside the fince line, from the Master gate operator to the Slave gate
operator.
3. Coverage Area C - Outside-Closed Coverage:
Install one photo-sensor: Outside the fence line, from one fence edge to the other.
4. Connect the photo-sensors to whichever unit is most convenient. For wiring instructions,
see Section C, Connecting Input Wiring, below.
Rev E
Doc 01-20201
10 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
BIPARTING SWING GATES
Figure 7. Biparting Swing Gates Photo-Sensor Layout.
WARNING
Buy only UL-approved photo-sensors made for use with vehicular gate
operators or system. Otherwise, safe gate operation may be compromised.
IMPORTANT NOTE: The installation shown in Figure 7 above is a suggested layout using emitters and
receivers. Any UL-approved photo-sensors are acceptable, but they must cover the entire area of
gate travel to be effective.
Install photo-sensors in three Coverage Areas as shown in Figure 7.
1. Coverage Area A - Inside-Open Coverage:
Install two photo-sensors: Inside the fence line, from the gate posts to the gate fully open positions.
2. Coverage Area B - Inside-Closed Coverage:
Install one photo-sensor: Inside the fince line, from the gate open position across the full length of
both gates.
3. Coverage Area C - Outside-Closed Coverage:
Install one photo-sensor: Outside the fence line, from gate post to gate post.
4. Connect the photo-sensors to whichever unit is most convenient. For wiring instructions, see
Section C, Connecting Input Wiring, below.
Rev E
Doc 01-20201
11 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
BIPARTING BARRIER GATES
Figure 8. Biparting Barrier Gates Photo-Sensor Layout.
WARNING
Buy only UL-approved photo-sensors made for use with vehicular gate
operators or system. Otherwise, safe gate operation may be compromised.
IMPORTANT NOTE: The installation shown in Figure 8 above is a suggested layout using emitters and
receivers. Any UL-approved photo-sensors are acceptable, but they must cover the entire area of
gate travel to be effective.
Install photo-sensors in three Coverage Areas as shown in Figure 8.
1. Coverage Area A - Inside-Open Coverage: not needed in barrier gate installation.
2. Coverage Area B - Inside-Closed Coverage:
Install one photo-sensor: Inside the fince line, from the Master gate operator to the Slave gate
operator.
3. Coverage Area C - Outside-Closed Coverage:
Install one photo-sensor: Outside the fence line, from one fence edge to the other.
4. Connect the photo-sensors to whichever unit is most convenient. For wiring instructions, see
Section C, Connecting Input Wiring, below.
B. PHOTO-SENSOR INSTALLATION FOR TRAP/TANDEM GATE CONFIGURATION
Photo-sensors must be installed on each gate separately. For instructions see the Installation and
Operation Manual for the gates.
Rev E
Doc 01-20201
12 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
1. Disconnecting the STOP terminal from the COMMON terminal stops the gate and prevents all
commands from having any effect. Manual Open does not activate the Reclose Timer.
2. If gate(s) are used for bi-directional traffic, the Exit Loop should be a directional loop detector.
3. Inside and Outside Interrupt Loops:
♦ For maximum safety, Inside and Outside Interrupt loops require separate loop detectors.
♦ Bipart or Bipart Latch: If only one loop detector is used, the Outside loop must also be
connected to the Inside loop detector.
INPUTS:
MasterSlave I/O
(TB1)
Input/output terminals are used for communication between Master and Slave
gate operators (see Section B below).
INDICATORS:
XMIT
Indicates data is being sent to the other gate operator (Master or Slave).
Indicates data is being received from the other gate operator (Master or Slave).
RECV
CONTROLS (S1):
NOTE: Both gates must be set to same gate type (SLIDE, SWING, BARRIER, or LINEAR). See the
Installation and Operation manual for the specific gate, Part 2 System Installation, Section J Setting Gate
Control Switch S1 for proper settings.
MASTER (S1-5)
BIPART (S1-6)
Sets the gate to MASTER (right) or SLAVE (left).
In conjunction with the switch S1-7, sets configuration for master/slave system
(see Section F below).
LATCH/TRAP (S1-7) In conjunction with the switch S1-6 swith, sets configuration for master/slave
system (see Section F below).
Rev E
Doc 01-20201
14 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
D. MASTER/SLAVE INTERCONNECTION
•
•
A conduit between the Master and Slave units should be provided for the Master/Slave
interconnection cable.
Two shielded twisted pair wire 16 AWG to 24 AWG will be connected between the two units at TB1
on the controller Board
NOTES:
1. Do not run the Master/Slave cable and AC power wires in the same conduit.
2. Master/Slave interconnection cabel should not exceed 3000 feet in length.
E. MASTER/SLAVE WIRING
1. Select the desire gate layout in Section G.
2. Be sure to turn off BOTH gate operator units.
3. Wire all external control devices to their connection on the control board shown. See the Installation
and Operation instructions for the gate operators, Appendix A for details on how each control input
affects the gate operator.
4. Connect the Master/Slave interconnect cable: connect the Receive inputs (RECV1, RECV2) on each
board to the Transmit inputs (XMIT1, XMIT2) on the other board (see Figure 10).
5. Turn on power to the Slave gate operator.
6. Turn on power to the Master gate operator.
7. Set switch S1 on Master and Slave units to your configuration according to section F.
8. Perform the Post Assembly Procedure and the Final Assembly of Gate Operator instructions, as
found in Part 2 of the Installation and Operation instructions for the gate operators.
NOTE
Be sure to connect the two units correctly. Improper wiring of the Master/Slave interconnection
prevents proper operation of the system.
Figure 10. Master Slave Connection and Switch S1 Location.
Rev E
Doc 01-20201
15 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
G. SYSTEM LAYOUTS AND CONTROL WIRING
Additional
Master Wiring
Can use Radio or Cycle if
(if needed):
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Directional Exit Loop
Swing gate open
direction and its
maximum arc.
Warning Relay
Tel. Line
Inside Interrupt Loop
Shadow Loop
Gate
Operator
Master
Gate
Operator
Slave
(swing gates only)
Master/Slave Cable
Slide, Barrier or Swing Gate
Fence
Slide, Barrier or Swing Gate
Fence
Outside Interrupt Loop
Directional Exit Loop
Can use Radio or Cycle if
Exit Loop is not used.
1398F8
Figure 12. Bi-Part, Bi-Directional Gate System.
NOTE: If Radio is used, only one receiver/transmitter is required for both directions.
Additional
Master Wiring
(if needed):
Can use Radio* or Cycle if
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Exit Loop
Swing gate open
direction and its
maximum arc.
Warning Relay
Tel. Line
Inside Interrupt Loop
Shadow Loop
Gate
Operator
Slave
Gate
Operator
Master
(swing gates only)
Master/Slave Cable
Slide, Barrier or Swing Gate
Fence
Slide, Barrier or Swing Gate
Fence
Outside Interrupt Loop
1398F9
Figure 13. Bi-Part, Uni-Directional Gate System
(Swing gate, if used, opens in).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
17 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Fire
Can use Radio or Cycle if
Exit Loop is not used.
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Exit Loop
Outside Interrupt Loop
Warning Relay
Tel. Line
Swing Gate
Swing Gate
Gate
Operator
Master
Gate
Operator
Slave
Master/Slave Cable
Shadow Loop
Fence
Fence
Inside Interrupt Loop
Swing gate open
direction and its
maximum arc.
1398F10
Figure 14. Bi-Part, Uni-Directional Gate System
(Swing gate opens out).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Additional
Master Wiring
(if needed):
Can use Radio or Cycle if
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Directional Exit Loop
Inside Interrupt Loop
Swing gate open
direction and its
maximum arc.
Warning Relay
Tel. Line
Shadow Loop
Gate
Operator
Slave
Gate
Operator
Master
(swing gates only)
Master/Slave Cable
Slide, Barrier or Swing Gate
Slide, Barrier or Swing Gate
Fence
Fence
Outside Interrupt Loop
Directional Exit Loop
Can use Radio or Cycle if
Exit Loop is not used.
1398F11
Figure 15. Bi-Part, Bi-Directional Gate System.
NOTE: If Radio is used, only one receiver/transmitter is required for both directions.
Rev E
Doc 01-20201
18 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Can use Radio* or Cycle if
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensor
MagLock
Exit Loop
Swing gate open
direction and its
maximum arc.
Warning Relay
Tel. Line
Inside Interrupt Loop
Shadow Loop
Gate
Operator
Slave
Gate
Operator
Master
(swing gates only)
Master/Slave Cable
Slide, Barrier or Swing Gate
Fence
Slide, Barrier or Swing Gate
Fence
1398F12
Figure 16. Bi-Part Latch, Uni-Direction Gate System
(Swing gate, if used, opens in).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Additional
Master Wiring
Can use Radio* or Cycle if
(if needed):
Exit Loop is not used.
Fire
Manual Inputs
Exit Loop
Interrupt Bar
Photo-Sensors
MagLock
Outside Interrupt Loop
Swing Gate
Warning Relay
Tel. Line
Swing Gate
Gate
Operator
Slave
Gate
Operator
Master
Master/Slave Cable
Shadow Loop
Fence
Fence
Inside Interrupt Loop
Swing gate open
direction and its
maximum arc.
1398F13
Figure 17. Bi-Part Latch, Uni-Directional Gate System
(Swing gate opens out).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
19 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Can use Radio or Cycle if
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Directional Exit Loop
Inside Interrupt Loop
Tel. Line
Shadow Loop
(swing gates only)
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Slide, Barrier or Swing Gate
Outside Interrupt Loop
Additional
Slave Wiring
(if needed):
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Directional Exit Loop
Can use Radio or Cycle if
Exit Loop is not used.
1398F14
Figure 18. Bi-Directional Trap Gate System
(Swing Gate, if used, opens in).
NOTE: If Radio will be used in both gates, each gate will require a separate receiver/transmitter with a
separate entry code.
Rev E
Doc 01-20201
20 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Can use Radio or Cycle if
Exit Loop is not used.
Additional
Master Wiring
(if needed):
Directional Exit Loop
Outside Interrupt Loop
Slide, Barrier or Swing Gate
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Tel. Line
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Shadow Loop
(swing gates only)
Inside Interrupt Loop
Additional
Slave Wiring
(if needed):
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Directional Exit Loop
Can use Radio or Cycle if
Exit Loop is not used.
1398F15
Figure 19. Bi-Directional Trap Gate System
(Swing gate opens out).
NOTE: If Radio will be used in both gates, each gate will require a separate receiver/transmitter with a
separate entry code.
Rev E
Doc 01-20201
21 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Can use Radio* or Cycle if
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Exit Loop
Inside Interrupt Loop
Tel. Line
Shadow Loop
(swing gates only)
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Slide, Barrier or Swing Gate
Outside Interrupt Loop
Additional
Slave Wiring
(if needed):
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
1398F16
Figure 20. Uni-Directional Trap Gate System
(internal Swing gate, if used, opens in).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
22 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Can use Radio* or Cycle if
Exit Loop is not used.
Additional
Master Wiring
(if needed):
Exit Loop
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Outside Interrupt Loop
Swing Gate
Tel. Line
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Shadow Loop
Inside Interrupt Loop
Additional
Slave Wiring
(if needed):
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
1398F17
Figure 21. Uni-Directional Trap Gate System
(internal Swing gate opens out).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
23 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Outside Interrupt Loop
Tel. Line
Slide, Barrier or Swing Gate
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Shadow Loop
(Swing gate only)
Inside Interrupt Loop
Additional
Slave Wiring
(if needed):
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Exit Loop
Can use Radio* or Cycle if
Exit Loop is not used.
1398F18
Figure 22. Uni-Directional Trap Gate System
(external Swing gate, if used, opens in).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
24 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Inside Interrupt Loop
Shadow Loop
Tel. Line
Gate
Swing gate open
direction and its
maximum arc.
Operator
Master
Swing Gate
Outside Interrupt Loop
Additional
Slave Wiring
(if needed):
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Exit Loop
Can use Radio* or Cycle if
Exit Loop is not used.
1398F19
Figure 23. Uni-Directional Trap Gate System
(external Swing gate opens out).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
25 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Can use Radio or Cycle if
Exit Loop is not used.
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Directional Exit Loop
Inside Interrupt Loop
Warning Relay
Tel. Line
Gate
Operator
Master
Shadow Loop
(swing gates only)
Swing gate open
direction and its
maximum arc.
Slide, Barrier or Swing Gate
Outside Interrupt Loop
Additional
Slave Wiring
(if needed):
Master/
Slave
Cable
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Warning Relay
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Directional Exit Loop
Can use Radio or Cycle if
Exit Loop is not used.
1398F20
Figure 24. Bi-Directional Tandem Gate System
(Swing gate, if used, opens in).
NOTE: If Radio is used, only one receiver/transmitter is required for both directions.
Rev E
Doc 01-20201
26 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Can use Radio or Cycle if
Exit Loop is not used.
Fire
Directional Exit Loop
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Outside Interrupt Loop
Swing Gate
Warning Relay
Tel. Line
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Shadow Loop
Inside Interrupt Loop
Additional
Slave Wiring
(if needed):
Manual Inputs
Interrupt Bar
Photo Sensors
MagLock
Master/
Slave
Cable
Warning Relay
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Directional Exit Loop
Can use Radio or Cycle if
Exit Loop is not used.
1398F21
Figure 25. Bi-Directional Tandem Gate System
(Swing gate opens out).
NOTE: If Radio is used, only one receiver/transmitter is required for both directions.
Rev E
Doc 01-20201
27 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Warning Relay
Tel. Line
Outside Interrupt Loop
Slide, Barrier or Swing Gate
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Shadow Loop
(Swing gates only)
Inside Interrupt Loop
Additional
Slave Wiring
(if needed):
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Master/
Slave
Cable
Warning Relay
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Exit Loop
Can use Radio* or Cycle if
Exit Loop is not used.
1398F22
Figure 26. Uni-Directional Tandem Gate System
(Swing gate, if used, opens in).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
28 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional
Master Wiring
(if needed):
Fire
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Warning Relay
Tel. Line
Inside Interrupt Loop
Shadow Loop
Gate
Operator
Master
Swing gate open
direction and its
maximum arc.
Swing Gate
Outside Interrupt Loop
Additional
Slave Wiring
(if needed):
Master/
Slave
Cable
Manual Inputs
Interrupt Bar
Photo-Sensors
MagLock
Warning Relay
Gate
Operator
Slave
Inside Interrupt Loop
Slide or Barrier Gate
Outside Interrupt Loop
Exit Loop
Can use Radio* or Cycle if
Exit Loop is not used.
1398F23
Figure 27. Uni-Directional Tandem Gate System
(Swing gate opens out).
* WARNING
If Radio is used, gate system becomes bi-directional, compromising safety and security.
Rev E
Doc 01-20201
29 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
H. TROUBLESHOOTING
Units work as stand-alone:
1. Miswired or disonnected Master/Slave interconnect cable.
2. Improper Master/Slave switch S1 setting.
3. Bad Control board.
Units are not synchronized:
Improper Operator Pair setting. See programming step 02, Operator Type.
One gate braking to stop causes a fault in the other (moving) gate:
1. Both units are wired to the same circuit breaker.
2. Undersized power wires.
Rev E
Doc 01-20201
30 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC REQUIREMENTS
INSTALLATION
When you are ready to install this system, call your telephone company and give them the following information:
1. The telephone number of the line to which you will connect the system.
2. The FCC registration number for the system, which is DS83E7 - 17196 - ALE.
3. The ringer equivalence number (REN) which is 0.1B.
This system connects to the telephone line by means of a standard jack called the USOC RJ11C. If this type of
jack is not available where you want to install the system, you will need to order it from the telephone company.
TYPE OF SERVICE
Your LiftMaster operator is designed to be used on standard-device telephone lines. They should not be used on
coin service or party lines. If you have any questions about your telephone line, such as how may pieces of
equipment you can connect to it, the telephone company will provide this information upon request.
TELEPHONE COMPANY PROCEDURES
The goal of the telephone company is to provide you with the best service it can. In order to do this, it may
occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these
changes might affect your service or operation of your equipment, the telephone company will give you notice, in
writing, to allow you to make any changes necessary to maintain uninterrupted service.
IF PROBLEMS ARISE
If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone
line, as it may cause harm to telephone network. If the telephone company notes a problem, they may temporarily
discontinue service. When practical, they will notify you in advance of this documentation. If advance notice is not
feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct
the problem and informed of your right to file a complaint with the FCC.
In the event that any repairs are ever needed on your system, they should be performed only by an authorized
representative of LiftMaster, Inc.
DISCONNECTION
If you should ever decide to permanently disconnect your operator from its present line, please call the telephone
company and let them know of this change.
RADIO FREQUENCY
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet prepared by the FCC helpful: "How to Identify and Resolve
Radio-Television Interface Problems". This booklet is available from the United States Government Printing Office.
Washington, D.C., 20402. Stock No. 004-000-00345-4.
Rev E
Doc 01-20201
31 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE TO CANADIAN USERS
NOTICE: The Industry Canada label identifies certified equipment. This certification means that the
equipment meets telecommunications network protective, operation and safety requirements as
prescribed in the appropriate Terminal Equipment Requirements document(s). The Department does not
guarantee the equipment to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the equipment.
For their own protection, users should ensure that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or an electrician, as appropriate.
Rev E
Doc 01-20201
32 of 33
Download from Www.Somanuals.com. All Manuals Search And Download.
COPYRIGHT 2002
ALL RIGHTS RESERVED
This document is protected by copyright and may not be copied or adapted without the prior written consent of
LiftMaster. This documentation contains information proprietary to LiftMaster and such information may not be
distributed without the prior written consent of LiftMaster. The software and firmware included in the LiftMaster
product as they relate to this documentation are also protected by copyright and contain information proprietary
to LiftMaster.
FOR TECHNICAL SUPPORT OR TO ORDER REPLACEMENT PARTS, CALL OUR TOLL FREE NUMBER:
(800) 528-2806 Tucson, AZ
Monday thru Friday 5 AM – 6 PM, Saturday, 7 AM – 3:30 PM (PST)
Visit us at www.liftmaster.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|