Cateye Bicycle Accessories CC ED300 User Manual

• Pay attention to the road or trail! Do not be distracted by the  
computer.  
• Be sure to securely mount the magnet, the sensor, and the  
bracket on your bicycle. Periodically check to insure they are  
mounted securely and the screws are not loosen.  
CAT EYE ENDURO 8  
CYCLOCOMPUTER CC-ED300  
E: Owner’s Manual  
®
Warning  
• Keep batteries out of reach of small children. Dispose of batter-  
ies according to local regulations.  
• Avoid unnecessary prolonged exposure to the sun. Never at-  
tempt to disassemble the computer head.  
• Don’t use thinner, benzene or alcohol to wipe the surface of the  
computer. They may damage the surface of computer.  
ENDURO8  
Important  
Note  
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending  
Copyright © 2002 CAT EYE Co. Ltd.  
CCMED3-021210 066600240  
1
Please read these instructions carefully before attempting to  
install and use your CAT EYE ENDURO 8 computer so that you  
understand the functions of this product.  
Computer Set-up (For 1st use or after replacing the battery)  
Please don’t throw away this manual, Keep the manual at a place easily accessible.  
All Clear  
Installation of the Computer on Your Bike  
1 Push three buttons (MODE, START/  
The computer is combined with the following parts.  
STOP and SET) at the same time.  
* Do this procedure without fail for  
stable measurement when you use  
this system for the first time and every  
time the battery is replaced.  
3
3
2
1
4
8
7
SET Button  
5
6
7
8
SET Button  
Contact Point  
START/STOP Button  
MODE Button  
START/STOP  
Button  
2
1
1 Bracket  
2 Cord  
3 Sensor  
5 Magnet  
MODE Button  
You need to know the tire  
circumference (L cm) be-  
forehand.  
6 Bracket Rubber Pad  
7 Five Nylon Ties  
8 Spiral Tube  
Select The Measurement Unit  
!
2 Select the measurement unit, kilometer  
4 Sensor Rubber Pad  
or mile, by pushing the MODE button.  
5
Mount the magnet  
1
5 on a spoke of the front wheel so that the surface  
Sensor Side  
Mile  
Kilometer  
of the magnet will face the sensor.  
Spoke  
MODE  
Choose Either of The Followings.  
L cm  
• When you want to input the reading of the currently  
used odometer, keep pressing the MODE button for  
two seconds and input the reading.  
• When you want to start the odometer from zero,  
push the START/STOP button.  
Front Fork  
Mount sensor and adjust the gap between the  
You can refer to the guide  
chart to roughly know the  
tire circumference.  
2 magnet and the sensor.  
Secure the sensor 3 with the larger nylon ties 7 at  
the appropriate place and in the right direction.  
3
7
Starting the odom- Retaining the current odometer reading  
Tire size  
L(cm)  
eter from zero.  
(the odometer starts from the reading you  
inputted)  
14 x 1.50  
14 x 1.75  
16 x 1.50  
16 x 1.75  
18 x 1.50  
18 x 1.75  
20 x 1.75  
20 x 1-3/8  
22 x 1-3/8  
22 x 1-1/2  
24 x 1  
102  
106  
119  
120  
134  
135  
152  
162  
177  
179  
175  
Front Fork  
Important Note  
For two seconds.  
Marked Line  
Mount the sensor 3 at the appropri-  
ate position so that the center of the  
magnet 5 will align with the  
MODE  
ST/STOP  
Input the current reading of odometer.  
5
marked line on the sensor when the  
wheel is rotated.  
3
24 x 3/4Tubular 178  
Increase the  
number.  
3
24 x 1-1/8  
24 x 1-1/4  
24 x 1.75  
24 x 2.00  
24 x 2.125  
26 x 7/8  
179  
191  
189  
192  
196  
192  
191  
195  
195  
190  
207  
210  
200  
201  
202  
205  
206  
207  
207  
208  
217  
215  
216  
216  
217  
209  
212  
211  
207  
208  
209  
210  
211  
214  
217  
216  
213  
217  
218  
220  
Important Note  
MODE  
5
Rotate the sensor on the front fork to  
adjust the gap between the sensor  
and the magnet 5 within 5 mm, and  
secure it with the nylon ties.  
Move the  
decimal point.  
26 x 1(59)  
26 x 1(65)  
26 x 1.25  
26 x 1-1/8  
26 x 1-3/8  
26 x 1-1/2  
26 x 1.40  
26 x 1.50  
26 x 1.75  
26 x 1.95  
26 x 2.00  
26 x 2.10  
26 x 2.125  
26 x 2.35  
26 x 3.00  
27 x 1  
27 x 1-1/8  
27 x 1-1/4  
27 x 1-3/8  
650 x 35A  
650 x 38A  
650 x 38B  
700 x 18C  
700 x 19C  
700 x 20C  
700 x 23C  
700 x 25C  
700 x 28C  
700 x 30C  
700 x 32C  
700C Tubular  
700 x 35C  
700 x 38C  
700 x 40C  
Within 5 mm  
Center  
ST/STOP  
Mount The Bracket  
3 Secure the cord on the fork with the nylon ties 7 and lead to the handle bar along the outer  
SET  
cable of the bicycle by means of the spiral tube 8.  
Put the rubber pad 6 on the bracket 1 and secure the bracket on the handle bar with the  
screw. Slide the computer into the bracket 1 until you hear the click sound.  
The contact points are automatically closed. When you need to detach the computer, slide  
forward the computer with the lever pushed simultaneously.  
Note  
Set The Tire Circumference  
Set the tire circumference in cm.  
Note  
3
Allow enough wire clearance in the area marked with an  
turn the handlebar from left to right without pulling the wire.  
to insure that you can  
You can easily set it by referring to the chart shown  
right.  
Setting is completed by pushing the SET button.  
1
1
Lever  
Increase the  
number.  
Max. 300 cm  
8
6
MODE  
1
SET  
7
Decrease  
the number  
Min. 100 cm  
Rotate the front wheel.  
ST/STOP  
Test The Basic Functions  
4 Rotate the front wheel gently and see if the computer indicates the  
Preparation Complete.  
Tire size is usually shown  
on the sidewall of tires.  
running speed.  
OK  
(the screen will show the time measurement in this state)  
Note  
When the computer does not indicate the speed, check  
the position of the magnet and the sensor.  
* The auto mode is ON in this state.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Berkel Mixer FMS60 User Manual
Black Decker Can Opener EC75 User Manual
Bosch Appliances Mixer MUM 4405 UC User Manual
Bosch Appliances Security Camera NBN 921 User Manual
Brookstone Wheelchair OSIM USTYLE2 User Manual
Cables to Go Computer Drive 29345 User Manual
Casio Calculator fx 101 User Manual
Casio Watch MA0503 EA User Manual
Cisco Systems Car Video System OL 20811 01 User Manual
Cisco Systems IP Phone OL 21851 01 User Manual