Casio Watch MA1106 EA User Manual

MA1106-EA  
Operation Guide 5244  
Your watch may differ somewhat from the one shown in the illustration.  
For a watch with an elapsed time bezel  
Rotate the elapsed time bezel to align the  
minute hand.  
After certain amount of time elapsed, read the graduation on  
the elapsed time bezel which the minute hand points to.  
The elapsed time is indicated.  
mark with the  
Hour hand  
To set the time  
1. When the second hand is at  
12 o’clock, pull out the crown  
to the second click to stop it.  
2. Set the hands by rotating the  
crown. Rotate the crown to  
move the hands clockwise.  
Move the minute hand four or  
five minutes past the time you  
want to set, and then back it  
up to the proper setting.  
Minute hand  
Elapsed time bezel  
First click  
Some water resistant models are equipped with a screw  
lock crown.  
(Setting Day)  
With such models, you must unscrew the crown in the  
direction noted in the illustration to loosen it before you can  
pull it out. Do not pull too forcibly on such crowns.  
Also note that such watches are not water resistant while  
their crowns are loosened. Be sure to screw the crowns  
back in as far as they will go after making any setting.  
ꢀꢁ  
Second click  
(Setting Time)  
3. Push the crown back in to  
the normal position to restart  
timekeeping.  
Crown  
(Normal position)  
Specifications  
Day  
Second hand  
Accuracy at normal temperature: 20 seconds a month  
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),  
To set the day  
3 dials (timekeeping seconds, stopwatch minutes and 1/20 seconds), day  
1. Pull the crown out to the first click.  
2. Set the day by rotating the crown.  
Stopwatch function: Measuring capacity: 59'59.95"  
Measuring unit: 1/20 second  
Measuring mode: Elapsed time  
Battery: One silver oxide battery (Type: SR927W)  
Approximately 3 years on type SR927W (assuming one stopwatch operation 60 min./day)  
3. Push the crown back in to the normal position.  
Avoid changing the date setting while the current time is between 9:00 p.m. and  
1:00 a.m.  
Using the Stopwatch  
Stopwatch 1/20 second hand  
* This hand rotates and  
indicates the second count  
during the first 30 seconds.  
Stopwatch minute hand  
ꢀꢁ  
Stopwatch second hand  
The stopwatch lets you measure elapsed time up to 59 minutes, 59.95 seconds.  
To measure elapsed time (First 30 seconds)  
1. Press A to start the stopwatch.  
2. Press A to stop the stopwatch.  
You can resume the measurement operation by pressing A again.  
3. Check the elapsed time.  
The example below shows an elapsed time of 24.65 seconds.  
Stopwatch 1/20 second hand  
[.65]  
ꢀꢁ  
Stopwatch second hand  
[24 seconds]  
Press B to reset the stopwatch.  
This will enter the Timekeeping Mode.  
To measure elapsed time (After the first 30 seconds)  
1. Press A to start the stopwatch.  
During elapsed time measurement, the stopwatch 1/20 second hand  
automatically rotates for the final second of each minute.  
2. Press A to stop the stopwatch.  
You can resume the measurement operation by pressing A again.  
3. Press A and the stopwatch 1/20 second hand will move to the  
1/20 second count.  
If the elapsed time operation was stopped during the final second of each  
minute, the stopwatch 1/20 second hand will already be pointing at the  
1/20 second count. Do not press A at this time, because doing so will restart  
the elapsed time operation.  
4. Check the elapsed time.  
The example below shows an elapsed time of two minutes, 24.65 seconds.  
Stopwatch 1/20 second hand  
[.65]  
Stopwatch minute hand  
[2 minutes]  
ꢀꢁ  
Stopwatch second hand  
[24 seconds]  
Press B to reset the stopwatch.  
This will enter the Timekeeping Mode.  
Notes:  
Do not try to perform stopwatch operations while the crown is pulled out either  
to the first or second click. If you try to press a button, you might accidentally  
cause the crown to rotate and change the current time or day setting.  
If the starting positions of the stopwatch second hand and 1/20 second hand  
become misaligned, use the following procedures to adjust the positions of the  
hands so they point to 12 o’clock when the stopwatch is reset.  
To adjust the positions of the stopwatch hands  
1. Press B to reset the stopwatch, and check the stopwatch second hand,  
1/20 second hand, and minute hand. They all should be at 12 o’clock.  
2. To adjust the hands, pull out the crown to the second click.  
3. Press A to move the stopwatch second hand to 12 o’clock.  
Holding down A will move the second hand at high speed, until you release  
the button.  
4. Press B to move the stopwatch 1/20 second hand to 12 o’clock.  
Holding down B will move the 1/20 second hand at high speed, until you  
release the button.  
5. After making the adjustments you want, push the crown back in to its normal  
position. The stopwatch minute hand will move automatically to 12 o’clock.  
Note that pulling the crown out also stops the timekeeping second hand. After  
performing the above procedure, you should also adjust the timekeeping setting.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  

Billion Electric Company Network Router 7402VL User Manual
Black Decker MP3 Player 90535776 User Manual
Bose Speaker System 336 User Manual
Bravetti Cookware CW23HCH User Manual
Bravetti Food Processor BP100 User Manual
Briggs Stratton Air Cleaner 124L00 User Manual
Bushnell Digital Camera 11 9000 User Manual
Cadet Thermostat SBFT2 User Manual
Cadillac Washer Dryer XLR V User Manual
Cecilware Coffeemaker 2 QB User Manual