MO0603-EA
Operation Guide 2639 2819
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
• The actual level at which some functions are disabled depends on the watch model.
• Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to recover from a
single illumination operation.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately 50 minutes exposure to indoor fluorescent lighting
• Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
• The initial factory default Home City setting is TYO (Tokyo).This means that the
watch is initially configured to receive the time calibration signals transmitted in
Japan. If you are planning to use the watch in North America, be sure to change
the Home City setting.“To set your Home City” for more information.
• This watch does not have a time zone that corresponds to the Greenwich
Mean Time differential of –3.5 hours. Because of this, the radio-controlled
timekeeping and World Time functions will not display the correct time for
Newfoundland, Canada.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
Keep the watch exposed to bright light
The electricity generated by the solar cell of the watch is
Bright Light
l
l
l
• See “Power Saving Function” for more information.
l
stored by a built-in battery. Leaving or using the watch
where it is not exposed to light causes the battery to run
down. Make sure the watch is exposed to light as much as
possible.
l
About This Manual
• The operational procedures for Modules 2639 and 2819
are identical. All of the illustrations in this manual show
Module 2819.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
Solar cell
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
• You should try to keep the watch outside of your sleeve
as much as possible. Even if the face of the watch is
only partially blocked from light, charging will be reduced
significantly.
mode. Further details and technical information can be
found in the “Reference” section.
(Light)
Module 2639
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will cause some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light.
Battery discharges in the dark.
(Light)
Module 2819
Bright Light
Solar cell
Electrical
energy
(Converts light to
electrical power.)
All
functions
enabled
LEVEL 1
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 2
LEVEL 3
Dis-
charge
Some
functions
disabled
Charge
Rechargeable battery
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Time Recorder Mode
World Time Mode
Timekeeping Mode
L
Stopwatch Mode
Press C.
Alarm Mode
Radio-controlled Atomic Timekeeping
• Note that this watch does not have a city code that corresponds to Newfoundland.
4. Press A twice to exit the setting screen.
• The first press of A displays the 12/24-hour setting screen. Pressing A again exits
the setting screen.
This watch receives a time calibration signal and updates
its time setting accordingly. The time calibration signal
includes both Standard Time and Daylight Saving Time
(summer time) data.
PM
indicator
Day of week
• This watch is designed to pick up the time calibration
signal transmitted in the United States (Fort Collins,
Colorado) and the time calibration signals transmitted in
Japan.
Important!
• Normally, your watch should show the correct time as soon as you select your Home
City code. If it does not, it should adjust automatically after the next auto receive
operation (in the middle of the night).You can also perform manual receive or you
can set the time manually.
• The U.S. time calibration signal can be picked up by the
watch while in North America
.
*
• If you are in an area that does not use Daylight Saving Time (summer time), turn off
the DST setting.
The term “North America” in this User’s Guide refers
to the area that consists of Canada, the continental
United States, and Mexico.
Month – Day
*
Hour : Minutes Seconds
Time Calibration Signal Reception
There are two different methods you can use to receive the time calibration signal:
auto receive and manual receive.
Current Time Setting
This watch automatically adjusts its time setting in accordance with a time calibration
signal.You can also perform a manual procedure to set the time and date, when
necessary.
• The first thing you should do after purchasing this watch is to set your Home City,
which is the city where you will normally use the watch. For more information, see
“To set your Home City” below.
• When using the watch outside of the range of the U.S. and Japanese time signal
transmitters, you need to adjust the time manually as required. See “Timekeeping”
for information about manual settings.
• Auto Receive
With auto receive, the watch automatically picks up the time calibration signal four
times a day at 2:00 a.m., 3:00 a.m., 4:00 a.m., and 5:00 a.m. For more information,
see “About Auto Receive”.
• Manual Receive
Manual receive lets you start a time calibration receive operation with the press of a
button. For more information, see “To perform manual receive”.
Important!
• When getting ready to receive the time calibration signal, position the watch as
shown in the nearby illustration, with its 12 o’clock side facing towards a window.
Make sure there are no metal objects nearby.
To set your Home City
1. In the Timekeeping Mode, hold down A until the
transmitter indicator starts to flash, which indicates the
setting screen.
2. Press C once so the city code is flashing on the display.
3. Use D(east) and B(west) to select the city code you
want to use as your Home City.
• The following are the city codes for major cities in
Resin Band Metal Band
North America.
Transmitter indicator
City code
(P (Pacific) indicator):
LAX
Los Angeles, San Francisco, Las Vegas, Seattle,
Vancouver, Tijuana
(M (Mountain) indicator):
DEN
Denver, El Paso, Edmonton, Culiacan
CHI
• The watch should not be on its side or facing the wrong way.
(C (Central) indicator):
Chicago, Houston, Dallas/Fort Worth, New Orleans,
Winnipeg, Mexico City
(E (Eastern) indicator):
NYC
E/C/M/P indicator
New York, Detroit, Miami, Boston, Montreal
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide 2639 2819
To toggle a city code time between Standard Time and Daylight Saving Time
To turn an alarm on and off
1. In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
1. In the Alarm Mode, use D to select an alarm.
2. Press B to toggle it on and off.
DST indicator
• Turning on a one-time alarm (AL1, AL2, AL3,
AL4) displays the alarm on indicator on its Alarm
Mode screen, and in all modes. Turning on the snooze
alarm (SNZ) displays the alarm on indicator and
snooze alarm indicator on its Alarm Mode screen, and in
all modes.
Module 2639
• The DST indicator is on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
Alarm on indicator
Snooze alarm indicator
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
• Daylight Saving Time (DST) advances the time setting by one hour from Standard
Time. Remember that not all countries or even local areas use Daylight Saving Time.
• The watch will perform a signal receive operation even if it is in the World Time Mode
when a calibration time is reached. If this happens, the World Time Mode time
settings will be adjusted in accordance with the Home City time.
Module 2819
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly Time
Signal ( ).
2. Press B to toggle it on (Hourly Time Signal on
indicator displayed) and off (Hourly Time Signal on
indicator not displayed).
• The Hourly Time Signal on indicator is displayed in all
modes when the Hourly Time Signal is turned on.
Hourly time signal
on indicator
Time Recorder
SIG
The Time Recorder lets you store up to 30 records of the
Time record number
current time (month, day, hour, minutes, seconds, and
DST on/off setting) with the touch of a button. One way
you can use the Time Recorder is to record the start time
and the end time of a particular event.
To record a Time Recorder time
In the Timekeeping Mode, hold down B to record the
current Home City time (month, day, hour, minutes,
seconds, and DST on/off setting).
Recorded date
Stopwatch
• The recorded time flashes for about two seconds, and
(Month – Day)
then it is assigned a record number. After that, the
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
Hours
Seconds
Recorded time
(Hour : Minutes Seconds)
Timekeeping Mode screen appears.
• Records are assigned numbers sequentially from #01
through #30.
Minutes
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Storing a new time record when there are already 30 records stored in memory
automatically deletes record #01, shifts the remaining records upwards by 1, and
stores the new record as #30.
To recallTime Recorder times
In the Time Recorder Mode, use B (+) and D (–) to scroll through times stored in
memory.
• If you recorded a new Time Recorder time since you last entered the Time Recorder
Mode, the newest record appears first. If you have not recorded a new time, the
record you were viewing when you last exited the Time Recorder Mode appears first.
Home city time
1/100 second
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
To delete all Time Recorder times
In the Time Recorder Mode, hold down A to delete all Time Recorder times.
ElapsedTime
D
➤
➤B
Clear
D
Start
➤D
Stop
➤D
Re-start
Stop
Alarms
Split Time
The Alarm Mode gives you a choice of four one-time
Alarm number
alarms and one snooze alarm.
B
B
➤D
Stop
➤
D
Start
➤B
Split
(SPL displayed)
➤
Also use the Alarm Mode to turn the Hourly Time Signal
(SIG) on and off.
Split release
Clear
• There are five alarms numbered AL1 through AL4,
and SNZ.You can configure SNZ as a snooze alarm
only. Alarms AL1 through AL4 can be used as one-
time alarms only.
• Alarm settings (and Hourly Time Signal settings) are
available in the Alarm Mode, which you enter by
pressing C.
Two Finishes
B
D
➤B
Split release
Display time of
second runner.
➤
D
Start
➤B
Split
➤
Stop
Second runner
finishes.
Clear
Home city time
First runner
Alarm time (Hour : Minutes)
finishes.
Display time of
first runner.
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Backlight
The backlight uses an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch automatically turns on
the backlight when you angle the watch towards your face
in the dark.
• The auto light switch must be turned on (indicated by
auto light switch on indicator) for it to operate.
• See “Backlight Precautions” for other important
information about using the backlight.
AL1
SIG
AL2
SNZ
AL3
AL4
Module 2639
Auto light switch on indicator
2. After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3. Use C to move the flashing between the hour and
minute settings.
To turn on the backlight manually
In any mode, press L to illuminate the display for about
one second.
• The above operation turns on the backlight regardless of
the current auto light switch setting.
4. While a setting is flashing, use D (+) and B (–) to change it.
5. Press A to exit the setting screen.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. or p.m.
Module 2819
About the Auto Light Switch
Alarm Operation
Turning on the auto light switch causes the backlight to turn on for about one second,
whenever you position your wrist as described below in any mode. Note that this
watch features a “Full Auto EL Light,” so the auto light switch operates only when
available light is below a certain level. It does not turn on the backlight under bright
light.
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Moving the watch to a position that is parallel to the ground and then tilting it
towards you at more than 40 degrees causes the backlight to turn on.
• Wear the watch on the outside of your wrist.
Displaying the snooze alarm setting screen
To test the alarm
In the Alarm Mode, hold down B to sound the alarm.
Parallel to
ground
More than
40°
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide 2639 2819
Warning!
Charging Precautions
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it to
become quite hot. Take care when handling the watch to avoid burn injury. The watch
can become particularly hot when exposed to the following conditions for long periods.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
To turn the auto light switch on and off
In any mode, hold down L for about two seconds to toggle the auto light switch on
(auto light switch on indicator displayed) or off (auto light switch on indicator not
displayed).
• Under direct sunlight
Charging Guide
• The auto light switch on indicator is displayed in all modes while the auto light switch
is turned on.
After a full charge, timekeeping remains enabled for up to about six months.
• The following table shows the amount of time the watch needs to be exposed to light
each day in order to generate enough power for normal daily operations.
Power Supply
Exposure Level (Brightness)
Approximate
Exposure Time
This watch is equipped with a solar cell and a special rechargeable battery
(secondary battery) that is charged by the electrical power produced by the solar cell.
The illustration shown below shows how you should position the watch for charging.
Outdoor Sunlight (50,000 lux)
Sunlight Through a Window (10,000 lux)
Daylight Through a Window on a Cloudy Day (5,000 lux)
Indoor Fluorescent Lighting (500 lux)
5 minutes
24 minutes
48 minutes
8 hours
Solar cell
Example: Orient the watch so its face
is pointing at a light source.
• The illustration shows how to position
a watch with a resin band.
• Since these are the specs, we can include all the technical details.
•
•
•
•
•
Watch is not exposed to light
• Note that charging efficiency drops
when any part of the solar cell is
blocked by clothing, etc.
• You should try to keep the watch
outside of your sleeve as much as
possible. Even if the face of the watch
is only partially blocked from light,
charging will be reduced significantly.
Display on 18 hours per day, sleep state 6 hours per day
1 backlight operation (1.5 seconds) per day
10 seconds of alarm operation per day
4 times calibration reception per day
• Stable operation is promoted by frequent charging.
RecoveryTimes
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Exposure Level
(Brightness)
Approximate Exposure Time
Important!
Level 4
Level 3
Level 2
Level 1
3 hours
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Make sure that the watch is normally exposed to bright light
whenever possible.
Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy
Day (5,000 lux)
Indoor Fluorescent
Lighting (500 lux)
1 hour
14 hours
3 hours
5 hours
70 hours
14 hours
28 hours
• This watch uses a special rechargeable battery to store power produced by the solar
cell, so regular battery replacement is not required. However, after very long use, the
rechargeable battery may lose its ability to achieve a full charge. If you experience
problems getting the special rechargeable battery to fully charge, contact your
dealer or CASIO distributor about having it replaced.
143 hours
•
Never try to remove or replace the watch’s special battery yourself. Use of the wrong
type of battery can damage the watch.
57 hours
------------
------------
• The current time and all other settings return to their initial factory defaults whenever
battery power drops to Level 4 and when you have the battery replaced.
• Turn on the watch’s Power Saving function and keep it in an area normally exposed
to bright light when storing it for long periods. This helps to keep the rechargeable
battery from going dead.
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
Timekeeping
Battery Power Indicator
The battery power indicator on the display shows you the current status of the
rechargeable battery’s power.
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to set the current date and time manually.
• The watch is equipped with a Time Recorder feature that lets you record the current
Home City time (month, day, hour, minutes, seconds, and DST on/off setting) with
the touch of a button. See “To record a Time Recorder time” for more information.
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C.
Battery Power Indicator
Module 2639 Module 2819
Function Status
All functions enabled.
Level
1
Receive time
Day of week
PM
indicator
Module 2639
All functions enabled.
2
3
Press D.
Battery power
indicator
Beeper tone, backlight, calibration
signal reception, display, and
buttons are disabled.
Month – Day
Charge Soon Alert
Receive date
Hour : Minutes Seconds
All functions, including
timekeeping, are disabled.
4
Last Signal Screen
Module 2819
Setting the Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
• The Level 3 charge warning indicator tells you that battery power is very low, and
that exposure to bright light for charging is required as soon as possible.
• At Level 4, all functions are disabled and settings return to their initial factory
defaults. Functions are enabled once again after the rechargeable battery is
charged, but you need to set the time and date after the battery reaches Level 3
from Level 4.You will not be able to configure any of the other settings until the
battery reaches Level 2 after dropping to Level 4.
• The Home City reverts to TYO (Tokyo), which means that the watch is configured
to receive the Japanese time calibration signal, whenever battery power drops to
Level 4. If you are using the watch in North America, you will need to configure your
Home City code setting whenever battery power recovers after dropping to Level 4.
• Leaving the watch in direct sunlight or some other very strong light source can
cause the battery power indicator to temporarily show a reading that is actually
higher than the battery level. The correct battery power indicator should appear after
a few minutes.
• If you use the backlight or the alarms a number of times during a short period, the
recover indicator (RECOVER / RECOV) appears on the display and the following
operations become disabled until battery power recovers.
Backlight
Beeper tone
Calibration reception
To set the current time and date manually
1. In the Timekeeping Mode, hold down A until the
transmitter indicator starts to flash, which indicates the
setting screen.
2. Use A or C to move the flashing in the sequence
shown below to select other settings.
Transmitter indicator
Press C.
/ Press A.
Transmitter/
City Settings
C
Auto
Receive
Transmitter
City Code DST
A
After some time, battery power will recover and the recover indicator (RECOVER / RECOV)
will disappear, indicating that the above functions are enabled again.
Time/Date/
Power Saving
Settings
C
12/24-Hour
Format
Seconds
Day
Hour
Minutes
Year
Power
Saving
Month
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide 2639 2819
3. Use C to display the transmitter screen.
Radio-controlled Atomic Timekeeping Precautions
• The transmitter indicator that appears indicates whether the currently selected
• Strong electrostatic charge can result in the wrong time being set.
• The time calibration signal is bounced off the ionosphere. Because of this, such
factors as changes in the reflectivity of the ionosphere, as well as movement of the
ionosphere to higher altitudes due to seasonal atmospheric changes or the time of
day may change the reception range of the signal and make reception temporarily
impossible.
Home City code is one that supports time calibration signal reception.
This indicator:
Means this:
The currently selected Home City code supports signal reception.
The currently selected Home City code does not support signal
reception.
• Even if the time calibration signal is received properly, certain conditions can cause
the time setting to be off by up to one second.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
• The watch is designed to update the date and day of the week automatically for the
period January 1, 2000 to December 31, 2099. Setting of the date by the time
calibration signal cannot be performed starting from January 1, 2100.
• This watch can receive signals that differentiate between leap years and non-leap
years.
• Though this watch is designed to receive both time data (hour, minutes, seconds)
and date data (year, month, day), certain signal conditions can limit reception to time
data only.
• Normally, the signal reception date shown by the Last Signal screen is the date data
included in the received time calibration signal. When only time data is received,
however, the Last Signal screen shows the date as kept in the Timekeeping Mode at
the time of signal reception.
• If you are in an area where proper time calibration signal reception is impossible, the
watch keeps time within 15 seconds a month at normal temperature.
• If you have problems with proper time calibration signal reception or if the time
setting is wrong after signal reception, check your current city code, DST (summer
time), and auto receive settings. The following are the initial factory defaults for these
settings.
• 60 appears for the transmitter while
,
,
,
,
, or
NYC CHI DEN LAX ANC HNL
is selected as the Home City. In this case, there is not need to select a transmitter.
, or is selected as the
• You can change the transmitter when
,
HKG TYO
SEL
Home City. For details, see “To configure auto receive settings for Japan”.
4. Use C and A to select the other time and date settings, and change the settings
as described above.
5. When the setting you want to change is flashing, use B and/or D to change it as
described below.
City Settings
Screen:
To do this:
Do this:
Change the city code
Use D (east) and B (west).
Cycle between Daylight Saving Time Press D.
(ON), Standard Time (OFF), and
Auto DST (AUTO)
Toggle between auto receive on
(ON) and off (OFF)
Press D.
• See “City Code Table” for a complete list of available city codes.
Time/Date/Power Saving Settings
Setting
Transmitter
City code
Initial Factory Default
AUTO (Auto switching)
TYO (Tokyo)
Screen:
To do this:
Do this:
Toggle between 12-hour (12H) and Press D.
24-hour (24H) timekeeping
Reset the seconds to 00
Change the hour or minutes
Change the month, day, or year
DST (summer time) DST (Auto switching)
AUTO
Press D.
Use D (+) and B (–).
Use D (+) and B (–).
Auto receive
(Auto receive)
ON
To configure auto receive settings for Japan
Toggle the Power Saving on (ON)
and off (OFF)
Press D.
Note
• The following procedure applies when you have TYO (Tokyo) selected as your
Home City. If you are using the watch in the U.S., see “To configure the auto receive
setting for the U.S.”.
6. Use A to exit the setting screen.
• If a Transmitter/City Setting screen is displayed, press A twice.
• If a Time/Date/Power Saving Setting screen is displayed, press A once.
1. In the Timekeeping Mode, hold down A until the
transmitter indicator starts to flash, which indicates the
setting screen.
2. Use D to select the transmitter you want to use.
• Each press of D cycles through the available auto
receive settings as described below.
Note
• Auto DST (AUTO) can be selected only while HNL, ANC, LAX, DEN, CHI,
NYC, HKG, TYO, or SEL is selected as the Home City code. For more
information, see “Daylight Saving Time (DST)” below.
• The auto receive setting is used for time calibration signal reception only. See “About
Auto Receive” for details.
AUTO : The watch automatically selects the
frequency that has the strongest signal.
Daylight Saving Time (DST)
40 :
Receives the signal from Fukushima
(40kHz).
Receives the signal from Fukuoka/Saga
(60kHz).
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
Transmitter indicator
60 :
The time calibration signal transmitted from Fort Collins includes both Standard Time
and DST data. When the Auto DST setting is turned on, the watch switches between
Standard Time and DST (summer time) automatically in accordance with the received
time signal.
• The time calibration signals transmitted from Fukushima and Fukuoka/Saga do not
include summer time data.
• The default DST setting is Auto DST (AUTO) whenever you select HNL, ANC,
LAX, DEN, CHI, NYC, HKG, TYO, or SEL as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
3. Press C three times to move the flashing to the auto
receive on/off setting.
4. Press D to toggle auto receive on (ON) and off (OF).
5. Press A twice to exit the setting screen.
• Reception can take up to 12 minutes when the AUTO
option is selected.
Timekeeping
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced or when battery power drops to
Level 4.
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
calculated in accordance with the Greenwich Mean Time (GMT) differential for each
city, based on the your Home City time setting.
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the transmitter indicator starts to
flash, which indicates the setting screen.
2. Press C twice and the DST setting screen appears.
3. Use D to cycle through the DST settings in the sequence shown below.
Auto DST (AUTO)
DST off (OFF)
DST on (ON)
• GMT differential is calculated by this watch based on UTC data.
*
The letters “UTC” stands for “Universal Time Coordinated,” which is the world-wide
*
scientific standard of timekeeping. It is based upon carefully maintained atomic
4. When the setting you want is selected, press A twice to exit the setting screen.
(cesium) clocks that keep accurate to within microseconds. Leap seconds are
added or subtracted as necessary to keep UTC in sync with the Earth’s rotation.
The reference point for UTC is Greenwich, England.
Reference
12-hour/24-hour Timekeeping Formats
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also
applied in all other modes.
• When 12-hour timekeeping is selected, the P (p.m.) indicator is displayed from noon
to 11:59 p.m.
• Module 2639 also displays an A (a.m.) indicator from midnight until 11:59 a.m.
Module 2819 does not display any indicator during a.m. times.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Auto Return Features
• If you leave the watch in the Time Recorder Mode or Alarm Mode for two or three
minutes without performing any operation, it automatically returns to the
Timekeeping Mode.
• If you leave a screen with flashing digits on the display for two or three minutes
without performing any operation, the watch automatically saves anything you have
input up to that point and exits the setting screen.
Power Saving Function
When turned on, the Power Saving function automatically enters a sleep state
whenever the watch is left in an area where it is dark for a certain period. The table
below shows how watch functions are affected by the Power Saving function.
Data and Setting Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
ElapsedTime
in Dark
Display
Operation
60 to 70 minutes Blank, with Sleep indicator
All functions enabled, except
for the display
SLEEP
(
/ SLEEP) flashing
Initial Screens
When you enter the Alarm or World Time Mode, the data you were viewing when you
last exited the mode appears first.
6 or 7 days
Beeper tone, backlight, display,
and auto receipt of the
calibration signal are disabled.
Blank, with Sleep indicator
SLEEP
(
/ SLEEP) not flashing
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
• The watch will not enter the sleep state between 6:00 AM and 10:59 PM. If the
watch is already in the sleep state when 6:00 AM arrives, however, it will remain in
the sleep state.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation Guide 2639 2819
To recover from the sleep state
Perform any one of the following operations.
Move the watch to a well-lit area. It can take up to two seconds for the display to turn on
•
.
• Press any button.
• Angle the watch towards your face for reading.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A. This causes
the transmitter indicator to flash, which indicates the
setting screen.
|
|
|
2. Press A again.
3. Press C seven times until the Power Saving on/off
screen appears.
Module 2639
Power saving on indicator
4. Press D to toggle Power Saving on (ON) and off
(OFF).
|
5. After the setting is the way you want, press A to exit
the setting screen.
• The Power Saving on indicator is on the display in all
modes while the Power Saving is turned on.
|
Module 2819
Backlight Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight shortens the battery operating time.
Auto light switch precautions
• Wearing the watch on the inside of your wrist as well as movement or vibration of
your arm can cause the auto light switch to activate and illuminate the display. To
avoid running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
• Note that wearing the watch under your sleeve while the auto light switch is turned
on can cause frequent illumination of the face and can run down the battery.
• The backlight may not light if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• The backlight turns off in about one second, even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If the backlight
does not light, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back
towards you again. If this does not work, drop your arm
all the way down so it hangs at your side, and then bring
it back up again.
• Under certain conditions, the backlight may not light until about one second after you
turn the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
City Code Table
City
Code
– – –
HNL
GMT
Differential
–11
City
Other major cities in same time zone
Pago Pago
Papeete
Honolulu
Anchorage
–10
ANC
–9
Nome
San Francisco, Las Vegas, Vancouver,
Seattle/Tacoma, Dawson City, Tijuana
El Paso, Edmonton, Culiacan
Houston, Dallas/Fort Worth,
New Orleans, Mexico City, Winnipeg
Montreal, Detroit, Miami, Boston,
Panama City, Havana, Lima, Bogota
La Paz, Santiago, Port Of Spain
Sao Paulo, Buenos Aires, Brasilia, Montevideo
LAX
DEN
CHI
Los Angeles
Denver
–8
–7
–6
Chicago
NYC
New York
–5
CCS
RIO
Caracas
Rio De Janeiro
–4
–3
–2
–1
– – –
– – –
GMT
LON
PAR
BER
ATH
CAI
Praia
Dublin, Lisbon, Casablanca, Dakar, Abidjan
+0
+1
London
Paris
Berlin
Athens
Cairo
Milan, Rome, Madrid, Amsterdam, Algiers, Hamburg,
Frankfurt, Vienna, Stockholm
Helsinki, Istanbul, Beirut, Damascus,
Cape Town
+2
JRS
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
Jerusalem
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Dhaka
Yangon
Bangkok
+3
+3.5
+4
+4.5
+5
+5.5
+6
Kuwait, Riyadh, Aden, Addis Ababa, Nairobi, Moscow
Shiraz
Abu Dhabi, Muscat
Male
Mumbai, Kolkata
Colombo
+6.5
+7
Jakarta, Phnom Penh, Hanoi, Vientiane
Singapore, Kuala Lumpur, Beijing, Taipei, Manila, Perth,
Ulaanbaatar
HKG
Hong Kong
+8
SEL
TYO
ADL
SYD
NOU
WLG
Seoul
Tokyo
Adelaide
Sydney
Noumea
Wellington
Pyongyang
+9
+9.5
+10
+11
+12
Darwin
Melbourne, Guam, Rabaul
Port Vila
Christchurch, Nadi, Nauru Island
• Based on data as of June 2005.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|