1.888.227.2178
Table of Contents
What to Expect with
Your Installation
Congratulations on purchasing your new
Casablanca® ceiling fan! It will provide
comfort and performance in your home
or office for many years. This installation
and operation manual contains complete
instructions for installing and operating
your fan.
Tools Needed
Mounting Options
Ceiling Bracket
30 inches
4
2
3
9
5
We are proud of our work and appreciate
the opportunity to supply you with the
best ceiling fan available anywhere in the
world.
Downrod
Wiring
Canopy
Blades
To register your fan, please visit:
Save your receipt for proof of purchase.
6
10
11
Operation, Maintenance
& Cleaning
Light Kit
Remote Control
Troubleshooting
?
?
?
12
13
14
15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Tools Needed
Pliers
Wire Strippers
Screwdrivers
Ladder
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
O
34
CEILING
1.888.227.2178
Mounting Options
If you have a flat ceiling:
Hang your fan by a standard downrod (included).
Standard
Mounting
Support
Structure
Support
Structure
If you have an angled ceiling:
Ceiling
Outlet Box
(required)
1. You will need a longer downrod (sold separately).
Angled
Mounting
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Ceiling
Angled
(required)
Standard
Mounting
Style
Outlet Box
Mounting
Style
Use the three steps below to determine if your ceiling angle is greater than 34°
1
2
3
34°
PLACE
SLIDE
toward ceiling
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Guide Touches
but NOT Ceiling
Wall
Use Standard Mounting
or Low-Profile Mounting
Use Angled Mounting
to hang the fan from a
to hang the fan from a flat ceiling.
vaulted or angled ceiling.
You need BOTH
a Longer
You need ONLY
a Longer
Downrod &
an Angled
Downrod
Mounting Kit
*most common
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Ceiling Bracket
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
to support structure with
(provided with outlet
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
If you are unable to do this,
call Technical Support at
1-888-277-2178.
still attached.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Downrod
Standard
skip to next page
Downrod
for ceilings 8-10’ high
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
1
2
3
4
5
Shorter
Downrod
for fans installed
close to ceiling
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Put the wires and downrod through the canopy.
Let the canopy sit loosely on top of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
Using an orange wire
connector from
Using orange wire
connectors from
Green/Yellow
Stripe
the
hardware bag,
the
hardware bag,
connect the three
grounding wires
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the fan.
Connect the white wire
(grounded) from the
ceiling to the white wire
from the fan.
(green, green/yellow
stripe, or bare copper)
coming from the ceiling,
downrod, and hanging
bracket.
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Canopy
Screw
Holes
Position the canopy so that, when
Lift the canopy into place so that
Insert the two canopy screws
lifted into place, the canopy fits into
the screw holes are aligned.
found in the
hardware bag.
the hanging bracket as shown.
Note: Fan style may vary.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Blades
Attach a blade tip to each blade using
two blade tip screws, found in
Insert four blade assembly screws and four
blade washers, found in the hardware
the
hardware bag.
bag, into each blade as shown. Install the
screws into the posts in each blade arm.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Light Kit
Tab
Notch
Bulb
Install a halogen bulb in the light
socket. When necessary, replace
with bulbs of the same type and
wattage.
Position the notches in the outer
rim of the globe so they line up
with the tabs on the inside of the
rim on the light kit.
Carefully lift the globe up inside the
light kit as far as it will go, then rotate
the globe clockwise until it is held
tightly in place by the four tabs.
See next page for fan
operation instructions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Remote Control
Battery
Door
ON
Once the power
is turned on, the
remote must be
paired within 60
seconds. Pairing
is only required
once after initial
installation.
ON ECE
SET
1
2
3
4
ON ECE
1
2
3
4
Set
ON ECE
SET
1
2
3
4
Battery
Remove battery door. Change the
dip switch settings if the frequency
matches a previously installed remote
transmitter. Install A23 or MN21
alkaline battery in the proper polarity
and replace the battery door. To pair
the remote, hold down the Set button
for 5 seconds. Pairing is complete
when LED button flashes twice.
If a light kit is installed on your
fan, choose the light bulb
mode by moving the toggle
switch. For halogen bulbs, set
the switch to “ON.” Replace the
battery door.
To install the transmitter
cradle, hand-tighten the
provided screws to mount the
cradle to the wall.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Operation, Maintenance & Cleaning
LED
Fan
Speed
Dial
Off
(High)
(Low)
Reverse
Light
ON ECE
SET
1
2
3
4
_
+
For cleaning the fan, use soft
To select fan speed press one of
the numbers on the Fan Speed
Dial. To calibrate the fan speed,
run the fan on “6” for 90 seconds
after each AC power reset. The
LED light flashes to indicate a
signal has been sent to the fan.
To reverse the air flow direction,
press the Reverse button while
fan is running. Press Light button
to turn lights off/on. To dim the
lights, press the light button for
more than one second. Light will
cycle from brightest to dimmest.
Release the light button when
desired brightness is achieved.
To change the battery, remove
the battery door. Remove battery
and replace with A23 or MN21
alkaline battery. Please observe
proper polarity placement.
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
1.888.227.2178
Troubleshooting
Fan doesn’t work
Noisy Operation
Excessive wobbling
• Press a fan speed button (1-4).
• Tighten the blade and blade
• Tighten all of the blade screws
iron screws until they are snug.
AUTHORIZED SERVICE
CENTERS
until they are snug.
• Check the circuit breaker to
ensure the power is turned on.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
For the most updated list of
Casablanca Authorized Service
Centers, visit
• Check the wall control battery.
• Make sure that you have paired
call toll free 1-888-227-2178.
the wall control.
• Use the provided balancing
kit and instructions to balance
the fan.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 9.
Remote doesn’t work
Fan speeds are incorrect
• Install a fresh battery in the wall
control.
• Turn power from the circuit
breaker off and back on, then
run the fan on speed “6” for at
least 90 seconds and check the
fan speeds again.
• Make sure you have paired the
remote.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M8517-01 • 11/11/13 • © Casablanca Fan Company
|