Casablanca Fan Company Fan 59060 User Manual

1.888.227.2178  
Table of Contents  
To register your fan, please visit:  
What to Expect with  
Your Installation  
Tools Needed  
Mounting Options  
Ceiling Bracket  
Save your receipt for proof of purchase.  
Congratulations on purchasing your new Casablanca®  
ceiling fan! It will provide comfort and performance in  
your home or office for many years. This installation and  
operation manual contains complete instructions for  
installing and operating your fan.  
30 inches  
4
2
3
5
We are proud of our work and  
appreciate the opportunity  
to supply you with the best  
Preparation  
Downrod  
Wiring  
Wall Control  
Canopy  
ceiling fan available anywhere  
in the world.  
6
7
10  
18  
12  
13  
Maintenance  
& Cleaning  
Blades  
Light Kit  
Operation  
Troubleshooting  
?
?
?
14  
15  
20  
21  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Tools Needed  
Pliers  
Wire Strippers  
Screwdrivers  
Ladder  
9/64” Drill Bit  
(optional)  
Power Drill  
(optional)  
If mounting to a support structure, you will also need these tools.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
O
34  
CEILING  
Mounting Options  
If you have a flat ceiling:  
Hang your fan by a standard downrod (included).  
Standard  
Mounting  
Support  
Structure  
Support  
Structure  
If you have an angled ceiling:  
Ceiling  
Outlet Box  
(required)  
1. You will need a longer downrod (sold separately).  
Angled  
Mounting  
2. If your ceiling angle is greater than 34°, you will  
also need an Angled Mounting Kit (sold separately).  
Ceiling  
Angled  
(required)  
Standard  
Mounting  
Style  
Outlet Box  
Mounting  
Style  
Use the three steps below to determine if your ceiling angle is greater than 34°  
1
2
3
34°  
PLACE  
SLIDE  
toward ceiling  
FOLD  
against wall  
on dotted line  
Guide Touches  
BOTH Ceiling & Wall  
Guide Touches  
but NOT Ceiling  
Wall  
Use Standard Mounting  
to hang the fan from a flat ceiling.  
Use Angled Mounting  
to hang the fan from a  
vaulted or angled ceiling.  
You need BOTH  
a Longer  
You need ONLY  
a Longer  
Downrod &  
an Angled  
Downrod  
Mounting Kit  
*most common  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.888.227.2178  
Ceiling Bracket  
For angled ceilings, point  
opening toward peak.  
OFF  
Use wood screws  
(included) when securing  
to support structure with  
Use machine screws  
(provided with outlet  
box) when securing to  
Make sure all four bumpers are  
If you are unable to do this,  
call Technical Support at  
1-888-227-2178.  
still attached.  
approved electrical outlet existing ceiling fan-rated  
box. Drill 9/64” pilot holes  
outlet box. Make sure  
in support structure to aid  
it is securely installed  
in securing ceiling bracket and is acceptable for fan  
with hardware found in support of 31.8 kg (70 lbs)  
the  
hardware bag.  
or less.  
To avoid possible electrical shock, before  
installing your fan, disconnect the power by  
turning off the circuit breakers to the outlet  
box associated with the wall switch location.  
Refer to warning w.1 on pg. 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Preparation  
Ceiling Bracket (continued)  
Remove the shipping blocks from the  
motor. Discard the screws.  
Note: Some fans will have a shipping ring  
instead of shipping blocks. Please remove  
the ring and discard the screws.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Downrod  
Standard  
skip to next page  
Downrod  
for ceilings 8-10’ high  
If you need a different downrod length follow these steps:  
Steps 1-5 to remove standard downrod pipe  
Longer  
Downrod  
for angled  
ceilings or  
ceilings 10’ or  
higher  
1
2
3
4
5
10  
9
8
7
6
Steps 6-10 to reassemble with new pipe  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Downrod (continued)  
Remove the pre-installed  
setscrew so that the downrod  
can be inserted.  
The wires can be cut, but  
leave at least 8” extending  
from the top of the  
downrod.  
Slide the adapter cover onto  
the downrod, then hand  
tighten the downrod (at least  
4-5 full turns) until it stops.  
Tighten the setscrew  
with pliers. DO NOT  
HAND TIGHTEN.  
8”  
3/8”  
If the setscrew is not tightened  
securely, the fan may fall.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Downrod (continued)  
Lower the adapter cover until it rests  
flush against the motor housing.  
Align the screw holes on the adapter  
cover with the screw holes on the  
motor housing and install the  
Put the wires and downrod  
through the canopy. Let the  
canopy sit loosely on top of  
the fan.  
DO NOT PICK THE FAN UP BY  
THE CANOPY OR WIRES. Place  
the downrod ball into the slot  
in the ceiling bracket.  
three adapter cover screws found in  
the  
hardware bag.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Wiring  
Note: To connect the wires, hold  
the bare metal leads together and  
place a wire connector over them,  
then twist clockwise until tight.  
C
Receiver  
Using an orange wire connector  
from the hardware bag:  
Connect the 3 grounding wires  
(green, green/yellow stripe, or bare  
copper) coming from the ceiling,  
downrod, and ceiling bracket.  
green/yellow stripe  
Place the receiver on top of the downrod  
assembly as shown.  
Turn the splices upward and push them carefully back through the hanger bracket  
into the outlet box. Spread the wires apart, with the grounded wires on one side of  
the outlet box and the ungrounded wires on the other side of the outlet box.  
Refer to CAUTION c.1 on pg. 2  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Wiring (continued)  
Using an orange wire connector from  
Use wire strippers to remove the  
the  
hardware bag:  
crimp connector from the end of the  
red wire on the receiver.  
Connect the black wire  
(ungrounded) from the ceiling to  
the black wire from the receiver  
(marked “live in”).  
Using the wire connectors from the  
remote control hardware bag:  
Connect the white wire from the  
receiver (marked “common out”)  
to the white wire from fan.  
Connect the white wire (grounded)  
from the ceiling to the white wire  
from the receiver (marked “neutral  
in” or “common in”).  
Connect the black wire from the  
receiver (marked “fan out”) to  
the black wire from the fan.  
Connect the blue wire from the  
receiver (marked ”light 1 out”) to  
the blue wire from the fan  
Connect the red wire from the  
receiver (marked ”light 2 out”) to  
the red wire from the fan.  
M
Turn the splices upward and push them carefully back through the hanger bracket  
into the outlet box. Spread the wires apart, with the grounded wires on one side of  
the outlet box and the ungrounded wires on the other side of the outlet box.  
Refer to CAUTION c.1 on pg. 2  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Wall Control  
Screw  
Cut-Out  
Drywall  
Drill Holes  
Before  
Drywall  
Anchors  
Painters  
Tape  
Cover Plate  
Template  
Template  
Template  
After  
1. Tape the provided wall control  
template with painter’s tape at  
the desired installation area.  
2. Drill holes inside the four  
corners of the template.  
Note: Make sure the wall  
control template is level before  
proceeding to the next step.  
1. Using a 9/64 drill bit, drill a hole  
in each screw cut-out on the wall  
control template.  
2. Using a hammer, tap a drywall  
anchor found in the wall control  
hardware bag into each hole  
until the drywall anchor is flush  
with the wall.  
1. Using a drywall punch saw,  
cut out the interior shape of  
the template using one of  
the four drilled corners as a  
starting point.  
2. Remove the template and the  
cut-out section of drywall.  
1. Insert the wall control into the  
dry wall cut out.  
2. Align the screw holes in the wall  
control with the drywall anchors.  
3. Install the cover plate using  
a Phillips Head screwdriver  
to secure the two cover plate  
screws found in the wall control  
hardware bag through the wall  
control and into the drywall  
anchors.  
If you are using a outlet box for wall control installation, the wires coming from the wall  
control must be grounded using the attached green wire. If not placed in an outlet box, cap  
the green wire coming from the wall control with an included wire nut.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Canopy  
Screw  
Holes  
Position the canopy so that, when  
lifted into place, the canopy fits into  
the hanging bracket as shown.  
Lift the canopy into place so that  
the screw holes are aligned.  
Insert the two canopy screws  
found in the  
hardware bag.  
Note: Fan style may vary.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Blades  
Place each blade between a blade iron  
Once the blade and medallion are  
attached, insert the blade iron into  
the slot on the blade ring and install  
the blade iron armature screws, found  
Once all five blades have been  
assembled, lift the blade assembly  
and align the screw holes and  
rubber grommets on the blade ring  
with the screw holes on the motor.  
Install the blade ring screws, found  
and blade medallion. Install the blade  
screws, found in the hardware bag,  
to attach the medallion to the blade  
iron. Repeat for all blades.  
in the  
hardware bag.  
in the  
hardware bag.  
Your blades are shielded with Dust Armor® which  
is a nanotechnology coating that repels dust. For  
cleaning the fan, use soft brushes or cloths to prevent  
scratching. Cleaning agents may damage the finishes.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Light Kit  
Screw three housing assembly screws  
Feed the wires from the bottom of the  
fan through the center hole of the light  
kit, then wrap keyhole slots around  
the screws and twist counterclockwise.  
Tighten all three screws securely.  
from the  
hardware bag halfway into  
the motor housing.  
Make sure the light kit is securely attached to the  
motor housing. Failure to properly secure all three  
assembly screws could result in the light kit falling.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Light Kit (continued)  
Install a halogen bulb in each socket.  
When necessary, replace with bulbs of  
the same type and wattage.  
Using the ceramic wire connectors, connect  
Tuck the wires into the light kit, then lift the  
light fixture and align the screw holes in  
the light fixture with the screw holes in the  
light kit. Install the three light fixture screws,  
the blue wire from the fan to the blue wire  
from the light kit. Connect the white wire from  
the fan to the white wire from the light kit.  
found in the  
hardware bag.  
Note: Be sure to use the CERAMIC wire  
connectors to avoid fire hazard.  
Make sure the light fixture is securely attached to the light kit.  
Failure to properly secure all 3 assembly screws could result  
in the light fixture falling.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Light Kit (continued)  
Globe  
Finial Cap  
Finial  
Carefully lift the globe so the threaded rod  
on the light fixture goes through the hole  
in the globe. With the other hand, install  
the finial cap and finial onto the threaded  
rod and tighten securely.  
Install an E12 bulb in each upper socket.  
Note: Do not use CFL bulbs to replace your light  
bulbs. Your lights may flicker or fail to work.  
See next page for fan  
operation instructions.  
Note: Glass shade style and number of lights may vary.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Operation  
Battery  
Battery  
Holder  
ON  
4
Fan  
Power  
Battery  
Door  
Before operating the wall control, press on the  
battery door to eject it. Unscrew the battery  
holder. Insert the battery, found in the control  
hardware bag, with the positive (+) side facing  
downward. Reinstall the battery holder and  
reinsert the battery door into the wall control.  
The remote transmitter should already be  
paired to the receiver and ready to use.  
Note: If your need to pair your remote, turn  
fan power off and back on at the circuit  
breaker. Within three minutes, press and  
hold both the Fan Off button and the 4  
button for four seconds to pair the remote.  
To prevent faulty operation, please  
disconnect power from all other ceiling  
fans within range while pairing.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Operation (continued)  
Reverse  
Button  
The Safe-Exit Program gives  
you about thirty seconds of  
light when you turn the lights  
off to exit the room before the  
(Low)  
Fan  
Speed  
(a)  
Fan  
Speed  
lights go out.To use Safe-Exit:  
• Press the fan power button  
off for at least three seconds to  
initiate the Safe-Exit Mode.  
(High)  
• The lights will flash for visual  
confirmation.  
Downlights  
Uplights  
• The lights will stay on 50%  
brightness for 20 seconds and  
then begin to dim. After a total  
of 30 seconds, the lights will be  
completely off.  
(b)  
Reverse  
Fan  
Note: For CFL lighting, the lights  
will stay on 100% brightness  
for 30 seconds. After a total of  
30 seconds, the lights will be  
completely off.  
Power  
Battery  
Holder  
Quickly press the uplights or  
downlights button to turn the lights off  
and on. Press and hold the appropriate  
button to raise or dim the light level of  
the uplights or downlights. The reverse  
button changes the direction that the  
blades turn. The power button turns  
the fan off and on.  
The reverse button on the wall  
control changes the air flow  
pattern. In warm weather, use  
(a) downward air flow pattern.  
In cold weather, use (b) upward  
air flow pattern.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Maintenance & Cleaning  
Globe  
Finial Cap  
Finial  
OFF  
Be sure to turn off  
power to the fan  
before performing  
any maintenance or  
relamping.  
Changing the bulbs - unscrew the finial and  
remove it from the threaded rod. Remove the  
finial cap while supporting the globe with your  
other hand. Carefully remove the globe. Unscrew  
bulbs and replace with bulbs of the same type  
and wattage. Reinstall the globe assembly.  
Cleaning the fan - use soft brushes or cloths  
to prevent scratching. Cleaning products may  
damage the finishes.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  
1.888.227.2178  
Troubleshooting  
Fan doesn’t work  
Noisy Operation  
Lights dim when turned on or  
do not turn on at all.  
Excessive wobbling  
• Press a fan speed button (1-4).  
• Tighten the blade and blade  
iron screws until they are snug.  
• Tighten all of the blade and  
blade iron screws until they  
are snug.  
Make sure the wattage of the  
light bulbs installed matches  
the specifications on the  
light sockets (see page 19 for  
instructions on changing the  
bulbs).  
Check the circuit breaker to  
ensure the power is turned on.  
Check to see if any of the  
blades are cracked. If so, replace  
all of the blades.  
• Turn the power off, support  
the fan carefully, and check  
that the hanger ball is  
properly seated.  
• Check the wall control battery.  
Make sure that you have paired  
the wall control.  
• Use the provided balancing  
kit and instructions to balance  
the fan.  
• Make sure the blades spin freely.  
• Turn off power from the circuit  
breaker, then loosen the canopy  
and check all the connections  
according to the wiring diagram  
on pages 10-11.  
If you have multiple remotes or  
multiple remote-controlled fans  
installed on the same circuit  
breaker and you are experiencing  
interference or faulty operation of  
your remote controls, please go to  
and click “How do I properly install  
multiple remote-controlled fans?” for  
information on how to correct this  
issue.  
Remote doesn’t work  
AUTHORIZED SERVICE  
Install a fresh battery in the wall  
CENTERS  
For the most updated list of  
Casablanca Authorized Service  
Centers, visit  
control.  
Check the plug connection in  
the switch housing.  
Make sure you have paired the  
remote.  
call toll free 1-888-227-2178.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M8505-01 • 10/30/14 • © Casablanca Fan Company  

Belkin Network Router F6D6230XX4 User Manual
Belson Hair Dryer CM2938 User Manual
Billion Electric Company Network Card BIPAC 2AB 20 User Manual
Bosch Appliances Electric Pressure Cooker 5650 028 820 User Manual
Bosch Appliances Range HEI8054U User Manual
Bosch Power Tools Clock Radio PB360S User Manual
Bose Car Speaker 51 User Manual
Bowens Camera Flash BW7630 User Manual
Char Broil Charcoal Grill 12301719 User Manual
Char Broil Gas Grill 4638220 User Manual