1.888.227.2178
Table of Contents
Congratulations on purchasing your new
Casablanca® ceiling fan! It will provide
comfort and performance in your home
or office for many years. This installation
and operation manual contains complete
instructions for installing and operating
your fan.
What to Expect with
Your Installation
Preparation
Tools Needed
Ceiling Bracket
5
2
3
4
8
We are proud of our work and appreciate
the opportunity to supply you with the
best ceiling fan available anywhere in the
world.
Hanging the Fan
Wiring
Motor Housing
Blades
To register your fan, please visit:
Save your receipt for proof of purchase.
6
7
9
Maintenance
& Cleaning
Switch Housing
Light Kit
Troubleshooting
?
?
?
10
11
13
14
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Tools Needed
9/64” Drill Bit
(optional)
Power Drill
(optional)
Screwdrivers
Ladder
If mounting to a support structure, you will also need these tools.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Ceiling Bracket
Bumper
OFF
Use wood screws
(included) when securing
to support structure with
Use machine screws
(provided with outlet
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
Make sure all four bumpers are still attached.
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the
outlet box associated with the wall switch location.
Refer to warning w.1 on pg. 2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Preparation
Ceiling Bracket (continued)
Time Saver Tip: Get a helper
to insert grommets, found in
the hardware bag, into the
blades while you’re doing the
next couple of steps.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Hanging the Fan
Ground
Wire
Screw
Hole
Locking
Screw
While holding the wires out of the way, lift
the motor assembly and place the square
hanger into the opening in the ceiling
bracket. Be sure the ground wire attached
to the hanger faces out of the large
opening in the ceiling bracket.
Once the motor is in the ceiling
bracket, use the two locking screws
found in the
hardware bag to secure
the motor to the ceiling bracket.
Note: Fan style may vary.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
M
I
N
O
R
G
F
For Dual Switches
Using the orange wire
connectors from
Green/Yellow
Stripe
the
hardware bag,
connect the white wire
(grounded) from the
For a Single Switch
Using an orange wire
connector from
the hardware
bag, connect the 3
grounding wires (green,
green/yellow stripe, or
bare copper) coming
from the ceiling, fan,
and hanging bracket.
Using the orange wire
connectors from
ceiling to the white wire
from the fan.
the
hardware bag, connect
Connect the black wire
(ungrounded) from the
ceiling to the black wire
from the fan. Connect the
second (ungrounded) wire
from the ceiling to the blue
wire from the fan.
the black wire (ungrounded)
from the ceiling to the black
and the blue wires from the
fan. Connect the white wire
(grounded) from the ceiling to
the white wire from the fan.
F
N
A
O
M
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Motor Housing
Notch
Motor
Housing
Screw
Screw
Holes
Indentation
Raise the motor housing up over the motor
and ceiling bracket. Turn the motor housing
so the screw holes align and the indentation
in the housing locks into place with the notch
in the ceiling bracket. The motor housing is
not secured until the next step is complete.
Do not leave unattended.
With a Phillips head screwdriver, install
the four motor housing screws found
in the
hardware bag. Tighten all four
screws securely.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Blades
Insert grommets found in the
hardware
Lightly attach the blade irons to the
bag into the holes in the blades, then
secure each blade to a blade iron with
motor with screws found in
the
hardware bag, then securely
screws found in the
hardware bag.
tighten after both screws are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Switch Housing
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Screw two housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
Insert the third screw, found in
hardware bag, into place and then
tighten all three screws.
the
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Light Kit
Lift the lower switch housing
up until the screw holes line up
with the screw holes in the upper
switch housing.
Install a CFL bulb into each socket.
Connect the plugs from the
Insert three switch
housing screws, found in
upper and lower switch housings.
Make sure to line up the colored
markings on the connectors.
the
hardware bag.
Want to install your fan without a light kit?
“How do I install my fan without the light kit?”
Make sure the lower switch housing is securely attached to
the upper switch housing. Failure to properly secure all three
assembly screws could result in the light fixture falling.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Light Kit (continued)
Fan
Pull
Chain
Bowl
Light
Pull
Chain
Glass
Holder
Finial Cap
Finial
ON
Be sure to turn the
power back on at
the breaker and the
switch before trying
to operate fan.
Press the bowl and glass holder
flush against the metal plate.
Thread the light pull chain
through the hole in the center of
the finial cap and thread the fan
pull chain through the grommet
hole in the side of the finial cap.
Thread the light pull chain
through the hole in the finial and
screw the finial onto the threaded
rod. Connect the pull chain
pendants to the short chains
coming from the fan.
See next page for fan
operation instructions.
Note: Glass shade style and number of lights may vary.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Maintenance, Operation & Cleaning
Bowl
Glass
Holder
Finial Cap
Finial
OFF
Be sure to turn off
the power to the fan
before performing
any maintenance or
relamping.
Reverse
Switch
Changing the direction of air
flow - Move the reverse switch
to the opposite position.
Cleaning the fan - Use soft
Changing the bulbs - Unscrew
the finial and remove it from the
threaded rod. Remove the finial cap
and unscrew the globe keeper while
supporting the globe with your other
hand. Carefully remove the globe.
Unscrew bulbs and replace with
bulbs of same type and wattage.
Reinstall the globe assembly.
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
For questions regarding removing a light kit, call
customer service 1-888-227-2178.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
1.888.227.2178
Troubleshooting
Fan doesn’t work
Noisy Operation
Excessive wobbling
• Make sure power switch is on.
• Tighten the blade and blade
iron screws until they are snug.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Pull the pull chain to make sure
it is on.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Use the provided balancing
kit and instructions to balance
the fan.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 7.
• Check the plug connection in
the switch housing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M6017-01 • 04/11/13 • © Casablanca Fan Company
|