Casablanca Fan Company Fan 54036 User Manual

1.888.227.2178  
Table of Contents  
To register your fan, please visit:  
What to Expect with  
Your Installation  
Tools Needed  
Mounting Options  
Ceiling Bracket  
Save your receipt for proof of purchase.  
Congratulations on purchasing your new Casablanca®  
ceiling fan! It will provide comfort and performance in  
your home or office for many years. This installation and  
operation manual contains complete instructions for  
installing and operating your fan.  
30 inches  
4
2
3
5
We are proud of our work and  
appreciate the opportunity  
to supply you with the best  
Preparation  
Downrod  
Wiring  
Wall Control  
Canopy  
ceiling fan available anywhere  
in the world.  
6
7
10  
18  
12  
13  
Maintenance  
& Cleaning  
Blades  
Switch Housing  
Light Kit  
Operation  
Troubleshooting  
?
?
?
14  
15  
16  
20  
21  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Tools Needed  
Pliers  
Wire Strippers  
Screwdrivers  
Ladder  
9/64” Drill Bit  
(optional)  
Power Drill  
(optional)  
If mounting to a support structure, you will also need these tools.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
O
34  
CEILING  
1.888.227.2178  
Mounting Options  
If you have a flat ceiling:  
Hang your fan by a standard downrod (included).  
Standard  
Mounting  
Support  
Structure  
Support  
Structure  
If you have an angled ceiling:  
Ceiling  
Outlet Box  
(required)  
1. You will need a longer downrod (sold separately).  
Angled  
Mounting  
2. If your ceiling angle is greater than 34°, you will  
also need an Angled Mounting Kit (sold separately).  
Ceiling  
Angled  
(required)  
Standard  
Mounting  
Style  
Outlet Box  
Mounting  
Style  
Use the three steps below to determine if your ceiling angle is greater than 34°  
1
2
3
34°  
PLACE  
SLIDE  
toward ceiling  
FOLD  
against wall  
on dotted line  
Guide Touches  
BOTH Ceiling & Wall  
Guide Touches  
but NOT Ceiling  
Wall  
Use Standard Mounting  
or Low-Profile Mounting  
Use Angled Mounting  
to hang the fan from a  
to hang the fan from a flat ceiling.  
vaulted or angled ceiling.  
You need BOTH  
a Longer  
You need ONLY  
a Longer  
Downrod &  
an Angled  
Downrod  
Mounting Kit  
*most common  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Ceiling Bracket  
OFF  
For angled ceilings, point  
opening toward peak.  
Use wood screws  
Use machine screws  
(included) when securing  
to support structure with  
(provided with outlet  
box) when securing to  
approved electrical outlet existing ceiling fan-rated  
box. Drill 9/64” pilot holes  
outlet box. Make sure  
in support structure to aid  
it is securely installed  
in securing ceiling bracket and is acceptable for fan  
with hardware found in support of 31.8 kg (70 lbs)  
the  
hardware bag.  
or less.  
Make sure all four bumpers are  
If you are unable to do this,  
call Technical Support at  
1-888-277-2178.  
still attached.  
To avoid possible electrical shock, before  
installing your fan, disconnect the power by  
turning off the circuit breakers to the outlet  
box associated with the wall switch location.  
Refer to warning w.1 on pg. 2  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Preparation  
Time Saver Tip: Get a helper  
to insert grommets, found in  
the  
hardware bag, into the  
Remove the shipping blocks from the  
motor. Save the screws. They will be  
needed for blade iron installation.  
blades while you’re doing the  
next couple of steps.  
Note: Some fans will have a shipping  
ring instead of shipping blocks. Please  
remove the ring and save the screws.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Downrod  
Standard  
skip to next page  
Downrod  
for ceilings 8-10’ high  
If you need a different downrod length follow these steps:  
Steps 1-5 to remove standard downrod pipe  
Longer  
Downrod  
for angled  
ceilings or  
ceilings 10’ or  
higher  
1
2
3
4
5
Shorter  
Downrod  
for fans installed  
close to ceiling  
10  
9
8
7
6
Steps 6-10 to reassemble with new pipe  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Downrod (continued)  
Remove the pre-installed  
setscrew so that the downrod  
can be inserted.  
Hand tighten the downrod (at  
least 4-5 full turns) until it stops.  
The wires can be cut, but  
leave at least 8” extending  
from the top of the downrod.  
Tighten the setscrew  
with pliers. DO NOT  
HAND TIGHTEN.  
8”  
3/8”  
If the setscrew is not tightened  
securely, the fan may fall.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Downrod (continued)  
Put the wires and downrod through the canopy.  
Let the canopy sit loosely on top of the fan.  
DO NOT PICK THE FAN UP BY THE  
CANOPY OR WIRES. Place the downrod  
ball into the slot in the ceiling bracket.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Wiring  
Note: To connect the wires, hold  
the bare metal leads together and  
place a wire connector over them,  
then twist clockwise until tight.  
C
Receiver  
Using an orange wire connector  
from the hardware bag:  
Connect the 3 grounding wires  
(green, green/yellow stripe, or bare  
copper) coming from the ceiling,  
downrod, and ceiling bracket.  
green/yellow stripe  
Place the receiver on top of the downrod  
assembly as shown.  
Turn the splices upward and push them carefully back through the hanger bracket  
into the outlet box. Spread the wires apart, with the grounded wires on one side of  
the outlet box and the ungrounded wires on the other side of the outlet box.  
Refer to CAUTION c.1 on pg. 2  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Wiring (continued)  
C
Using the orange wire connectors  
from the remote control hardware bag:  
Using the orange wire connectors  
from the hardware bag:  
Connect the yellow wire from  
the receiver to the black wire  
from the fan.  
Connect the black (ungrounded)  
wire from the ceiling to the black  
wire from the receiver.  
white  
Connect the blue wire from the  
receiver to the blue wire (or  
possibly black with white stripe  
wire) from the fan.  
Connect the white (grounded)  
wire from the ceiling to both the  
white wire from the receiver and  
the white wire from the fan.  
M
Turn the splices upward and push them carefully back through the hanger bracket  
into the outlet box. Spread the wires apart, with the grounded wires on one side of  
the outlet box and the ungrounded wires on the other side of the outlet box.  
Refer to CAUTION c.1 on pg. 2  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Wall Control  
Screw  
Cut-Out  
Drywall  
Drill Holes  
Before  
Drywall  
Anchors  
Painters  
Tape  
Cover Plate  
Template  
Template  
Template  
After  
1. Tape the provided wall control  
template with painter’s tape at  
the desired installation area.  
2. Drill holes inside the four  
corners of the template.  
Note: Make sure the wall  
control template is level before  
proceeding to the next step.  
1. Using a 9/64 drill bit, drill a hole  
in each screw cut-out on the wall  
control template.  
2. Using a hammer, tap a drywall  
anchor found in the wall control  
hardware bag into each hole  
until the drywall anchor is flush  
with the wall.  
1. Using a drywall punch saw,  
cut out the interior shape of  
the template using one of  
the four drilled corners as a  
starting point.  
2. Remove the template and the  
cut-out section of drywall.  
1. Insert the wall control into the  
dry wall cut out.  
2. Align the screw holes in the wall  
control with the drywall anchors.  
3. Install the cover plate using  
a Phillips Head screwdriver  
to secure the two cover plate  
screws found in the wall control  
hardware bag through the wall  
control and into the drywall  
anchors.  
If you are using a outlet box for wall control installation, the wires coming from the wall  
control must be grounded using the attached green wire. If not placed in an outlet box, cap  
the green wire coming from the wall control with an included wire nut.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Canopy  
Screw  
Holes  
Position the canopy so that, when  
lifted into place, the canopy fits into  
the hanging bracket as shown.  
Lift the canopy into place so that  
the screw holes are aligned.  
Insert the two canopy screws  
found in the  
hardware bag.  
Note: Fan style may vary.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Blades  
Remember the screws that  
you kept after removing the  
shipping blocks (page 6)? You  
need them plus five more from  
the hardware bag for this step.  
Lightly attach the blade irons to the  
Insert grommets found in the  
hardware  
motor with screws found in  
bag into the holes in the blades, then  
secure each blade to a blade iron with  
the  
hardware bag, then securely  
tighten after both screws are attached.  
screws found in the  
hardware bag.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Switch Housing  
Feed the wire plug through the center  
hole of the upper switch housing, then  
wrap keyhole slots around the screws and  
twist counterclockwise.  
Insert the third screw, found in  
Screw two housing assembly screws  
from the hardware bag halfway into  
the motor housing. It does not matter  
which two screw holes you choose.  
the  
hardware bag, into place and  
then tighten all three screws.  
Make sure the upper switch housing is securely  
attached to the mounting plate. Failure to properly  
secure all 3 assembly screws could result in the switch  
housing fixture falling.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Light Kit  
Connect the plugs from the upper and  
Lift the lower switch housing up until the  
screw holes line up with the screw holes in  
the upper switch housing.  
Install the three switch housing screws,  
found in the hardware bag.  
lower switch housings. Make sure to line  
up the colored markings on  
the connectors.  
Want to install your fan without a light kit?  
“How do I install my fan without the light kit?”  
Make sure the lower switch housing is securely attached to the  
upper switch housing. Failure to properly secure all 3 assembly  
screws could result in the switch housing fixture falling.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Light Kit (continued)  
Globe  
Globe  
Keeper  
Finial Cap  
Finial  
Install a bulb into each of the sockets.  
When necessary, replace with bulbs of the  
Press the globe flush against the metal plate.  
With other hand, press the globe keeper over  
the threaded rod until it cups the glass and  
immediately install the finial cap and screw  
the finial onto the threaded rod.  
same type and wattage.  
See next page for fan  
operation instructions.  
Note: In compliance with US federal energy regulations, this ceiling  
fan contains a device that restricts its light output. Exceeding the  
wattage limit marked on the MAX wattage sticker affixed to the  
light socket(s) may result in fire hazard or improper operation.  
Note: Glass shade style and number of lights may vary.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Operation  
Battery  
Battery  
Holder  
ON  
Battery  
Door  
Before operating the wall control, press on the  
battery door to eject it. Unscrew the battery  
holder. Insert the battery, found in the control  
hardware bag, with the positive (+) side facing  
downward. Reinstall the battery holder and  
reinsert the battery door into the wall control.  
The remote transmitter is already paired  
to the receiver and ready to use.  
Note: If you would like to operate  
multiple fans or multiple remotes,  
or if your remote is not working,  
please see the Troubleshooting  
section at the end of this manual.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Operation (continued)  
Reverse  
Button  
The Safe-Exit Program gives  
you about thirty seconds of  
light when you turn the lights  
off to exit the room before the  
(Low)  
Fan  
Speed  
(a)  
Fan  
Speed  
lights go out.To use Safe-Exit:  
• Press the fan power button  
off for at least three seconds to  
initiate the Safe-Exit Mode.  
(High)  
• The lights will flash for visual  
confirmation.  
Lights  
Down  
Lights  
Up  
• The lights will stay on 50%  
brightness for 20 seconds and  
then begin to dim. After a total  
of 30 seconds, the lights will be  
completely off.  
(b)  
Reverse  
Fan  
Note: For CFL lighting, the lights  
will stay on 100% brightness  
for 30 seconds. After a total of  
30 seconds, the lights will be  
completely off.  
Power  
Battery  
Holder  
Quickly press the up or down arrow to turn the lights off  
and on. Hold the up or down arrow to raise or dim the light  
level. The reverse button changes the direction that the  
blades turn. The power button turns the fan off and on.  
The reverse button on the wall  
control changes the air flow  
pattern. In warm weather, use  
(a) downward air flow pattern.  
In cold weather, use (b) upward  
air flow pattern.  
Dimming Mode: To enable dimming, you must first set  
your remote to Dimming Mode. To toggle Dimming  
Mode on or off, hold down the Fan Power button while  
pressing the Light Down arrow twice.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Maintenance & Cleaning  
Globe  
Globe  
Keeper  
OFF  
Finial Cap  
Finial  
Be sure to turn off  
power to the fan  
before performing  
any maintenance or  
relamping.  
Changing the bulbs - unscrew the finial and  
remove it from the threaded rod. Remove  
the finial cap and the globe keeper while  
supporting the globe with your other hand.  
Carefully remove the globe. Unscrew bulbs  
and replace with bulbs of the same type and  
wattage. Reinstall the globe assembly.  
Cleaning the fan - use soft brushes or cloths  
to prevent scratching. Cleaning products may  
damage the finishes.  
For questions regarding removing a light kit, call  
customer service 1-888-227-2178.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Troubleshooting  
Remote does not work  
Excessive wobbling  
Fan doesn’t work  
Make sure the battery is installed  
correctly.  
• Tighten all of the blade and  
blade iron screws until they  
are snug.  
• Press a fan speed button (1-4).  
AUTHORIZED SERVICE  
CENTERS  
For the most updated list of  
Casablanca Authorized Service  
Centers, visit  
• Check the wall control battery.  
• Install a new battery.  
Check the circuit breaker to  
ensure the power is turned on.  
• Turn the power off, support  
the fan carefully, and check  
that the hanger ball is  
properly seated.  
If the remote still does not  
work, you may need to pair  
your remote. To prevent faulty  
operation, please disconnect  
power (at the wall switch,  
call toll free 1-888-227-2178.  
• Make sure the blades spin freely.  
• Turn off power from the circuit  
breaker, then loosen the canopy  
and check all the connections  
according to the wiring diagram  
on page 10-11.  
• Use the provided balancing  
kit and instructions to balance  
the fan.  
breaker, or fan) from all other  
ceiling fans within range while  
pairing. To pair: cycle power  
to the fan by turning power off  
and back on at the wall switch  
(or circuit breaker if necessary).  
Within three minutes, press and  
hold both the Fan Off button and  
the 4 button for four seconds to  
pair the remote. If applicable, the  
fan will turn on and the lights  
will flash and stay on to indicate  
successful pairing.  
Lights will not dim  
• To enable dimming, you  
must first set your remote to  
Dimming Mode. To toggle  
Dimming Mode on or off, hold  
down the Fan Power button  
while pressing the Light Down  
arrow twice.  
Lights dim when turned on or  
do not turn on at all.  
Check the plug connection in  
the switch housing.  
Make sure the wattage of the  
light bulbs installed matches  
the specifications on the  
light sockets (see page 20 for  
instructions on changing the  
bulbs).  
Ensure each bulb you are using  
supports dimming.  
Noisy Operation  
• Tighten the blade and blade  
iron screws until they are snug.  
Check to see if any of the  
blades are cracked. If so, replace  
all of the blades.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  
1.888.227.2178  
Troubleshooting (continued)  
Installing Multiple Fans with Independently Operating Remote Controls  
Installing One Fan Operating on Multiple Remote Controls  
To install multiple fans with independently operating remote controls, there is no need to  
perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply  
install each receiver into a fan and use the appropriate transmitter to operate each fan.  
To have multiple remote controls operate one fan, you must pair each additional transmitter  
to the receiver in the fan. The transmitter that shipped with your fan is already paired.  
Note: To prevent faulty operation, please disconnect power (at the wall switch,  
breaker, or fan) from all other ceiling fans within range while pairing.  
If your remote is not working, see the “Remote does not work” section on the previous page.  
For each additional transmitter, cycle power to the fan by turning power off and back on at  
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both  
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the  
fan will turn on and the lights will flash and stay on to indicate successful pairing.  
Installing Multiple Fans Operating on a Single Remote Control  
“Unpairing” Procedure for Faulty Operation of Remote Controls  
X
To have multiple fans operated by a single remote control, you must pair the transmitter to each  
additional receiver. The receiver that shipped with your fan is already paired to the transmitter.  
If a transmitter is mistakenly operating a fan, you need to “unpair” the transmitter from that  
fan’s receiver. The “unpairing” procedure is the same as the pairing procedure.  
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,  
breaker, or fan) from all other ceiling fans within range while pairing each fan.  
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch,  
breaker, or fan) from all other ceiling fans within range while “unpairing” a fan.  
For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all  
other fans while pairing. To pair: cycle power to the fan by turning power off and back on at  
the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both  
the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the  
fan will turn on and the lights will flash and stay on to indicate successful pairing.  
Disconnect power from all other fans while “unpairing.” Then, cycle power to the fan you  
wish to “unpair” by turning power off and back on at the wall switch (or circuit breaker  
if necessary). Within three minutes, press and hold both the Fan Off button and the 4  
button for four seconds to “unpair” the remote. If applicable, the fan will turn off and the  
lights will flash and turn off to indicate successful “unpairing.”  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
M6003-01 • 04/16/15 • © 2012–2015 Casablanca Fan Company  

Belkin Network Card F5U252 User Manual
Blomberg Dishwasher DWT37300NBL00 User Manual
Briggs Stratton Portable Generator 260700 User Manual
Brother Sewing Machine 882 U10 User Manual
Bush Hog Compact Loader 1947 User Manual
Canon Camera Lens EF17 40MM F 4L USM User Manual
Canon Photo Printer CDP E063 010 User Manual
Carrier Heat Pump 50RTP03 20 User Manual
Cecilware Coffeemaker BC2 IT User Manual
Chromalox Electric Heater CAF 20215 User Manual