1.888.227.2178
Table of Contents
What to Expect with
Your Installation
Ceiling Bracket
Installation
Tools Needed
Mounting Options
Congratulations on purchasing
your new Casablanca® ceiling
fan! It will provide comfort and
performance in your home or office
for many years. This installation
and operation manual contains
complete instructions for installing
and operating your fan.
30 inches
7 feet
Ladder
3
2
3
7
5
Wiring
Preparation
Downrod
Canopy
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan please visit:
6
10
11
Maintenance &
Cleaning
Blades
Switch Housing
Troubleshooting
?
?
ON
?
12
13
15
16
1
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
O
CEILING
34
Mounting Options
Tools Needed
Use this guide to determine
which mounting option is
appropriate for your ceiling type.
Flat
skip to next page
1. You will need a Longer Downrod
sold separately
2. You may need an Angle Mounting Kit
sold separately
Angled
Use the 3 steps below to determine if
your ceiling angle is greater than 34°
Wire Strippers
Pliers
Ladder
If installing an outlet box, you will also need:
2
3
1
FOLD
PLACE
SLIDE
on dotted line
against wall
toward ceiling
Guide Touches
Guide Touches
Wall
BOTH Ceiling & Wall
but NOT Ceiling
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
9/64” Drill Bit
(optional)
Power Drill
(optional)
Downrod
Screwdrivers
*most common
3
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Mounting Options (continued)
Support Brace
Support Brace
Ceiling
Outlet Box
(required)
8
12
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Use Standard or Low-Profile Mounting
to hang the fan from a flat ceiling by a
standard downrod (included).
Use Angled Mounting to hang the
fan from a vaulted or angled ceiling
(see previous page).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Ceiling Bracket Installation
For angled ceilings, point
opening toward peak.
OFF
Use wood screws
(included) when securing
to support structure with
Use machine screws
(provided with outlet
box) when securing to
Make sure all four (4) bumpers
are still attached.
If you are unable to do this,
call Technical Support at
1-888-227-2178.
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
in support structure to aid
outlet box. Make sure
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
Refer to warning w.1 on pg. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Preparation
Ceiling Bracket Installation (continued)
Time Saver Tip: Get a helper
to insert grommets, found in
the
hardware bag, into the
Remove the shipping blocks from
the motor. Save the five screws.
They will be needed for blade iron
installation.
blades while you’re doing the
next couple of steps.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Downrod
Standard
skip to next page
Downrod
for ceilings 8-10’ high
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
1
2
3
4
5
Shorter
Downrod
for fans installed
close to ceiling
10
9
8
7
6
Steps 6-10 to reassemble with new pipe
7
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Wiring
Note: To connect the wires,
hold the bare metal leads
together and place a wire
connector over them, then twist
clockwise until tight.
Using orange wire
connectors from
green/yellow stripe
Using an orange wire
connector from
the
hardware bag,
connect the black wire
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
(ungrounded) from the
ceiling to the black and
the blue wires from the
fan. Connect the white
wire (grounded) from
the ceiling to the white
wire from the fan.
M
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Insert the two canopy screws
Lift the canopy into place so that
the screw holes are aligned.
found in the
hardware bag.
Note: Fan style may vary.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Blades
Remember the screws that
you kept after removing the
shipping blocks (page 5)? You
need them plus five more from
hardware bag for this step.
Insert grommets found in the
hardware
Lightly attach the blade irons to the
motor with screws found in
bag into the holes in the blades, then
secure each blade to a blade iron with
the
hardware bag, then securely
screws found in the
hardware bag.
tighten after both screws are attached.
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the finishes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Switch Housing
Feed the wire plug through the center
hole of the upper switch housing, then
wrap keyhole slots around the screws and
twist counterclockwise.
Insert the third screw, found in
hardware bag, into place and then
tighten all three (3) screws.
Screw two (2) housing assembly screws
from the hardware bag halfway into
the motor housing. It does not matter
which two screw holes you choose.
the
Make sure the upper switch housing is securely
attached to the mounting plate. Failure to properly
secure all 3 assembly screws could result in the switch
housing fixture falling.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Switch Housing (continued)
Connect the fandangle to the short chain
coming from the switch housing.
Lift the lower switch housing up until the
holes line up with the screw holes in the
upper switch housing. Install the three (3)
switch housing screws, found in
Connect the plugs from the upper and
lower switch housings. Make sure to
line up the colored markings on the
connectors.
the
hardware bag.
Make sure the lower switch housing is securely attached to the
upper switch housing. Failure to properly secure all 3 assembly
screws could result in the switch housing fixture falling.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Switch Housing (continued)
Maintenance & Cleaning
ON
The pull chain controls the fan:
high, medium, low, and off.
To switch the direction of air
flow, move the reverse switch
to the opposite position.
Cleaning the fan - use soft
brushes or cloths to prevent
scratching. Cleaning products
may damage the finishes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
1.888.227.2178
Troubleshooting
?
?
CLICK!
CLICK!
CLICK!
ON
?
Fan doesn’t work
Excessive wobbling
Noisy Operation
• Check the circuit breaker to
ensure the power is turned on.
• Tighten all of the blade and
blade iron screws until they
are snug.
• Tighten the blade and blade
iron screws until they are snug.
• Make sure the blades spin freely.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 10-11.
• Use the provided balancing
kit and instructions to balance
the fan.
• Check the plug connection in
the switch housing.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
M6002-01 • 06/07/12 • Casablanca Fan Company
|