Product
Instructions
IP Ready™ Series
FDW75C12N & FDP75C12N
Before attempting to connect or operate this product,
please read these instructions completely.
81-IN5329
04/28/06
Download from Www.Somanuals.com. All Manuals Search And Download.
FDW75C12N, FDP75C12N
IP Ready Network Housing
ASSEMBLING THE UNIT:
Remove content from all boxes. Contents should include:
IP Ready Network Housing with 12Vdc input, wall mount or
pendant mounting, heater & blowers, ready for standard IP
PTZ cameras.
ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):
Power 12Vdc, Class 2 Only
!
Total Power: 21 watts Housing only
Accessories (Heater/Blower): 21 watts
Heater: 20 watts
Blower: 1 watt
NOTE: This unit is designed for operation in an
upright position. Installing the housing
upside down may cause damage to
the internal equipment, and will void the
warranty.
Main Housing Assembly
Either with wall mount or pendant bracket
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding
!
the weight of the entire unit.
Dome Assembly - Clear or Tinted
CARE AND CLEANING OF DOMES:
Do not remove the protective film until the product is
assembled and installed.
All FDW75 and FDP75 units include an optically clear
polycarbonate dome. The dome is an optical device and
should be handled with extreme care. Leave protective film
on dome until product is fully assembled and installed. Even
though the dome is virtually unbreakable, it can be easily
scratched.
Clean only with a clean cotton cloth and warm water.
DO NOT use a strong solvent or cleanser!
3 Packet Assemblies
- ꢁ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION OF PTZ CAMERA
See model for specific instruction.
Listed on the following pages are the specific instructions
for each of the individual network cameras. See specific
instruction for the model that matches the unit you have.
INDEX OF CAMERAS
AXIS 213
5
6
AXIS 214
CANON VB-C10R
CANON VB-C50iR
CANON VC-C4R / VC-C50iR
ELMO PTC-200C
ELMO PTC-201
7
8
9
10
11
12
13
14
15
16
17
18
19
ELMO PTC-400C
ELMO PTC-401
JVC VN-C30U
PANASONIC BB-HCM381 / KX-HMC280
PIXORD 261 / 262
SONY SNCRZ30
SONY SNCRZ50
TOSHIBA IK-WB21A
- ꢂ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
AXIS 213
2539 Mounting Plate:
Attach camera using these (2) holes
½"
1"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
2"
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Axis 213 camera requires 3.5" of spacing for optimal
position within the housing. Use (4) 2" spacer(s), plus
(4) 1" spacer(s) and (4) ½" spacer(s) provided in the (2)
hardware packets.
(3) screws
in housing
- ꢃ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
AXIS 214
2685 Mounting Plate:
Attach camera using these (3) holes
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
2"
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Install the AXIS 214 camera to the 2685 mounting
plate using the (3) 3mm x 12mm bolt and lock washers
provided.
2. The AXIS 214 camera requires 2” of spacing for optimal
position within the housing. Use the 4 (2”) spacers
provided in the packet.
- ꢄ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
CANON VB-C10R
2539 Mounting Plate:
Attach camera using these (2) holes
½"
1"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
2"
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Canon VB-C10R camera requires 4" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
(3) screws
in housing
- ꢅ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
CANON VB-C50iR
2539 Mounting Plate:
Attach camera using these (2) holes
½"
1"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
2"
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Canon VB-C50iR camera requires 3.5" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
(3) screws
in housing
- ꢆ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
CANON VC-C4R / VC-C50iR
2539 Mounting Plate:
Attach camera using these (2) holes
1"
1"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
2"
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Canon VC-C4R / VC-C50iR camera requires 4" of
spacing for optimal position within the housing. Use (4)
2" spacer(s), plus (8) 1" spacer(s) provided in the (2)
hardware packets.
(3) screws
in housing
- ꢇ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-200C
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in the unit
before proceeding.
2539 Mounting Plate:
Attach camera using these (4) holes
½"
1"
2. The Elmo PTC-200C camera requires 3.5" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
2"
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
- ꢀ0 -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-201
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in
the unit before proceeding.
2539 Mounting Plate:
Attach camera using these (4) holes
½"
2. The Elmo PTC-201 camera requires 2½" of spacing for
optimal position within the housing. Use (4) 2" spacer(s)
plus (4) ½" spacer(s) provided in the (2) hardware
packets.
2"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
- ꢀꢀ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-400C
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in the unit
before proceeding.
2539 Mounting Plate:
Attach camera using these (4) holes
½"
1"
2. The Elmo PTC-400C camera requires 3.5" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
2"
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
- ꢀꢈ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-401
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in
the unit before proceeding.
2539 Mounting Plate:
Attach camera using these (4) holes
1"
2. In the packet, there will be a number of 2 inch and 1
inch spacers. Take four of the 1 inch spacers and screw
them onto the spacers that are on the base bracket
(to make a 3 inch spacer). Place two 8/32 X s Philips
head screws on the three inch spacer in the dome. Be
sure to place the screws so they line up with the two
open screw slots on the quick release bracket. Place
the Elmo PTC-401C pan/tilt and quick release bracket
in the housing, sliding the two open screw slots over the
screws in the housing. Slide the bracket forward, and
then tighten the captive screw on the bracket.
2"
1. Remove the mounting plate from the camera and
place it onto the quick release bracket using the (4)
metric 3M Phillips head screws provided with the kit.
Then place the ELMO mounting plate back onto the
Elmo PTC-401C.
- ꢀꢁ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
JVC VN-C30U
2539 Mounting Plate:
Attach camera using these (3) holes
½"
2. In the packet, there will be a number of 2 inch and
½ inch spacers. Take four of the ½ inch spacers and
screw them onto the spacers that are on the base
bracket (to make a 2½ inch spacer). Place two 8/32
X s Philips head screws on the two and a half inch
spacer in the dome. Be sure to place the screws so
they line up with the two open screw slots on the quick
release bracket. Place the JVC VN-C30U pan/tilt and
quick release bracket in the housing, sliding the two
open screw slots over the screws in the housing. Slide
the bracket forward, and then tighten the captive
screw on the bracket.
2"
1. Remove the mounting plate from the camera and
place it onto the quick release bracket using the (3)
metric 3M Phillips head screws provided with the kit.
Then place the mounting plate back onto the
JVC VN-C30U.
- ꢀꢂ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
PANASONIC BB-HCM381 / KX-HMC280
2539 Mounting Plate:
Attach camera using this hole
½"
1"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
2"
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Install the camera to the 2539 mounting plate using the
¼ x 20, washer and lockwasher provided.
2. The Panasonic BB-HCM381 / KX-HMC280 requires 3½"
of spacing to properly position the camera within the
housing.
- ꢀꢃ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
PIXORD 261 / 262
2630 Mounting Plate:
Attach camera using these (3) holes
½"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Install the camera to the 2630 mounting plate using
the (3) 8 x 32 x .5 flat head screws, nuts and washers
provided.
2. The PIXORD 261/262 cameras require ½“ of spacing to
properly position the camera within the housing. Use
(4) ½” spacers provided in the hardware packets.
- ꢀꢄ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
SONY SNCRZ30
2539 Mounting Plate:
Attach camera using this hole
2"
2. The SNCRZ30 require 2” of spacing to properly position
the camera within the housing. Use (4) 2” spacers
provided in the hardware packets.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Attach the camera to the 2539 mounting plate using
the (1) ¼ x 20 bolt, washer and lockwasher provided.
- ꢀꢅ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
SONY SNCRZ50
2539 Mounting Plate:
Attach camera using this hole
½"
2"
2. The SONY SNCRZ50 require 2 ½ ” of spacing to properly
position the camera within the housing. Use (4) 2”
spacers plus (4) ½ “ spacers provided in the hardware
packet.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Attach the SNCRZ50 camera to 2539 mounting plate
using 3mm x 8mm bolt lockwashers provided.
- ꢀꢆ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING QUICK RELEASE BRACKETS
TOSHIBA IK-WB21A
2539 Mounting Plate:
Attach camera using these (4) holes
1"
2"
2. The Toshiba 1K-WB21A requires 3” of spacing to properly
position the camera within the housing. Use (4) 2”
spacers plus (4) 1” spacers provided in the hardware
packets.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1. Remove the quick release bracket from the camera.
Using (4) 8 x 32 x 3/8 bolts and star washers attach the
quick release place to the 2539 mounting plate.
- ꢀꢇ -
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING THE HOUSING ASSEMBLY:
WIRING INSTRUCTIONS
Be sure the bracket is properly and securely mounted
RJ45
BNC
to a supporting structure capable of rigidly holding
!
the weight of the entire unit.
NOTE: This unit is designed for operation in an
upright position. Installing the housing
upside down may cause damage to
the internal equipment, and will void the
warranty.
(Large)
Power
(Small)
Alarms
INSTALLING PENDANT MOUNT
1. This unit includes a 1½" NPT housing for a standard 1½"
NPT pipe. The housing can be used with other brackets
designed with 1½" male pipe threads, such as the WM20G
wall mount bracket.
Wiring Color Code Power and Control Inputs
AFTER CAMERA INSTALLATION
2. Attach the housing coupling.
Make inside housing wiring connections following Chart B
below.
NOTE: Pipe threads should be clean and rust-
free. Use the Teflon™ tape included with
the housing on the threads.
Chart A Wiring Color Code
Power and Control Inputs (Outside of housing)
POWER
Add thread
sealing tape
1
2
3
4
Camera Power (+12 VDC)
Camera Power (-12 VDC)
Accessory Power (+12 VDC)
Accessory Power (-12 VDC)
Red
Orange
Yellow
Green
CONTROL RJ45 Ethernet Connector
ALARMS
1
2
3
4
Alarm 1
Alarm 2
Alarm 3
Common
Blue
Violet
Gray
White
Chart B Power and Control Outputs (Inside of housing)
A small roll of Teflon tape is provided with all pendant units.
Teflon Tape
POWER
1
2
Camera Power (+12 VDC)
Camera Power (-12 VDC)
Red
Orange
ALARMS
1
2
3
4
Alarm 1
Blue
Alarm 2
Alarm 3
Common
Violet
Gray
White
- ꢈ0 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Mount the housing assembly to the mounting bracket
and housing coupling. A safety cable is included with
the housing to temporarily hold it while making wiring
connections. Loop the safety cable over one of the set
screws on the housing coupling and make the appropriate
connections using the (2) screw-down connectors supplied.
2. The wall mount bracket provided with the FDW7 includes
a location for conduit entry. If you wish to install conduit to
the bracket remove the conduit hole plug. Install fitting from
below the wall mount and secure with conduit nut from
inside the bracket.
4. Undo the safety cable and twist the housing onto the
housing coupling. Secure all (3) setscrews provided on the
housing coupling.
3. Open the access door on the bottom of the wall mount by
loosening the screw nearest the mounting plate.
Set screws
INSTALLING WALL MOUNT
A wall mount bracket comes standard with this unit, and
a template is included to use as a guide for mounting the
bracKet to a wall.
1. Choose the desired location for installation and mark
the drill holes using the template. Screw (2) bolts (not
provided) about ¾ of the way into the (2) top holes. Run
approximately 8 of wiring out of the wall.
Access panel
4. Attach the wires from the wall to the connector provided.
using the wiring color code chart as a guide.
NOTE: Be sure the hardware and the mounting surface
can support the weight of the wall mount bracket
plus the weight of the housing and drive unit.
The load will be subjected to vibration from the
camera motor and wind.
5. Once all wiring connections are made, place the wires
inside the wall mount bracket and close the access door.
Secure with the screw removed earlier.
2. There is a safety lanyard that is attached to the inside of
the dome assembly. Take the open end of the lanyard and
loop it around the lanyard tab that is located inside the
housing top.
CONNECTING THE TRIM RING ASSEMBLY TO THE
HOUSING TOP:
1. Open the access door on the bottom of the wall mount by
loosening the screw nearest the mounting plate.
3. The safety lanyard is now attached to the housing.
- ꢈꢀ -
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View for Replacement Parts
12
Not included
on 12Vdc
housings
13
16
14
6
ꢀꢅ
(1)
11
10
(1)
(2)
9
8
(4)
(1)
ꢀꢆ
7
6
(2)
(2)
(3)
(2)
(2)
(1)
4
1
(4)
(8)
3
2
(1)
(1)
5
ꢀꢇ
(3)
(1)
(1)
(1)
(4)
(1)
(1)
(4)
1
(4)
(4)
(4)
(3)
(4)
(3)
- ꢈꢈ -
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts List
Part Number
Description
1
2
RPFD7501
FD7T
LOWER TRIM RING
TINTED REPLACEMENT CAPSULE
CLEAR REPLACEMENT CAPSULE
DOME CLAMPING BRACKET
24 VAC HEATER
FD7C
3
4
5
6
7
RPFD703
RPFD072
RPFD080
(12 VDC) BLOWER (USED IN 24V HOUSINGS)
CAMERA BRACKET
RPFD060
RPFD050 (MODEL FD7HB)
CONNECTION PCB (24VAC ONLY)
RPRH707 (MODEL FD7NHB) CONNECTION PCB (NETWORK MODELS) (24VAC ONLY)
8
RPFD040
RPFD709
RPFD2612
WM10
HOUSING HARDWARE
9
HOUSING TOP
10
11
12
13
14
15
16
17
18
19
HOUSING TOP - GASKET
WM10 WALL MOUNT
RPNET02
RPNET04
SD0170
NETWORK HOUSINGS POWER BOARD (NOT INCLUDED ON 12VDC UNITS)
NETWORK CAMERA BRACKETS
PENDANT HOUSING COUPLING
QUICK RELEASE PIPE COUPLING
PENDANT MOUNT BRACKET
SD0180
SD0160
RPPKH2090
RPPKH2071
RPPKE1100
HOUSING HARDWARE PACKET A
HOUSING HARDWARE PACKET B
ELECTRICAL PACKET
N/S RPPKE1125
N/S RPTRAN02
ELECTRICAL PACKET, HB, FIXED NETWORK
40VA WALL TRANSFORMER
- ꢈꢁ -
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Template
R .733
2.132
5.500
1.537
2.981
2.000
3.250
- ꢈꢂ -
Download from Www.Somanuals.com. All Manuals Search And Download.
|