OPERATING MANUAL
FOR THE AQUATICA PRO DIGITAL
HOUSING FOR THE CANON 5D Mk II
PRODUCT # 20062
Download from Www.Somanuals.com. All Manuals Search And Download.
1-
Shutter Release lever
2-
Main Dial access knob
3-
4-
5-
6-
7-
8-
9-
LCD Panel Illuminator lever
ISO / Flash exposure compensation button
AF / Drive selector button
Metering / WB selector button
Main Bulkhead Connector
Secondary Bulkhead Connector
Hydrophone
10-
11-
12-
13-
14-
15-
16-
17-
18-
19-
20-
21-
22-
23-
24-
25-
26-
27-
28-
29-
30-
31-
32-
33-
34-
35-
36-
37-
38-
39-
40-
41-
42-
43-
Focus/Zoom Control knob
Focus/Zoom Control pinion gear
Lateral Accessory Bulkhead port
Lens Release knob
Lens Release knob lever
Hot shoe connector
Grips (x2)
Port Release mechanism button
Removable Camera Tray
Bayonet Flange
Top Accessory Bulkhead port
Grip’s Accessories mounting holes (1/4”-20)
Mode Dial port window
Latches (x2)
Quick Control Dial access knob
AF-ON / AF-Start & Star access lever
Top LCD panel Window
Accessory mounting hole (1/4”-20)
Viewfinder Eyepiece
Mode Dial access knob
AF Point / Magnifier button
Set / Movie Shooting button
On/Off & Quick Control Dial switch lever
Rear LCD window
Erase button
Playback button
INFO activation button
Picture Style button
Menu button
Live View activating button
Rubber Anti Skid pad
Sacrificial Anodes (x2)
Accessories mounting holes (x3)
Moisture Alarm LED
page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS IN DETAIL
1.
2.
SHUTTER RELEASE LEVER: Pulling the shutter release lever back part way activates the camera meter and auto focus. Pulling the lever back all
the way fires the camera.
MAIN DIAL ACCESS KNOB: Rotates clockwise and counterclockwise. Use alone or in combination with other controls to select
or set various camera functions or modes. In “Manual” the exposure mode controls the shutter speed settings (see camera manual).
3.
4.
LCD PANEL ILLUMINATOR BUTTON: Press to engage the top LCD panel illuminator.
ISO / FLASH EXPOSURE COMPENSATION: Press to select ISO speed or to select exposure correction of the flash*
* (please note this is only in the event a Canon flash in a housing would be used)
5.
6.
7.
8.
9.
AF/ DRIVESELECTOR BUTTON: press to select either AF Mode or the DRIVE modes
METERING PATTERN / WHITE BALANCE MODE BUTTON: Press to select the appropriate metering mode and/or White Balance mode.
MAIN BULKHEAD CONNECTOR: To connect Flash Sync Cord. (Manual Nikonos Type by default other option available on request).
SECONDARY BULKHEAD CONNECTOR: For Flash Sync Cord. (Manual Nikonos Type by default other option available on request).
HYDROPHONE: This will record sound while video recording underwater, it is design to be effective underwater and will not function
properly if not immersed.
10.
11.
12.
13.
14.
15.
FOCUS/ZOOM KNOB: Turning allows manual focus of a single focus lens or rotation of the zoom mechanism of a lens.
FOCUS/ZOOM PINION GEAR: Engages and operates the focus or zoom gear attached to the lens.
LATERAL ACCESSORY BULKHEAD CONNECTOR: For additional accessories or control connector.
LENS RELEASE KNOB: activates the lens release button on the camera allowing easy removal of the lens.
LENS RELEASE KNOB LEVER: Applies pressure on the camera lens lock button
HOT SHOE CONNECTOR: connects the camera to the Flash Bulkhead. Slide this Connector into the camera Hot Shoe.
When detaching do not pull the cord as this might damage the electrical connections.
16.
17.
18.
19.
20.
21.
HAND GRIPS (X2): Left and right grip allowing the mounting of strobe arms and accessories.
PORT RELEASE MECHANISM BUTTON: Press down to release the locking mechanism when installing or removing a port or extension.
REMOVABLE CAMERA TRAY: Used to attach camera and slide in housing.
BAYONNET MOUNTING FLANGE: allows the mounting of different ports and extension rings on the housing.
ACCESSORY BULKHEAD CONNECTOR: For additional strobe or remote control connector.
GRIP’S ACCESSORIES MOUNTING HOLES: Two 1/4-20 TPI holes on each grip are ready to accept TLC Base Brackets or TLC Base Ball
for strobe arms or accessories.
22.
23.
24.
MODE DIAL PORT WINDOW: Enables viewing of the different release options
LATCHES: Two heavy duty latches with safety locks to protect against accidental opening.
QUICK CONTROL DIAL ACCESS KNOB: It rotates clockwise and counterclockwise. It can be used alone or in combination with other
controls to select or set various camera functions or modes. Refer to camera manual for in depth use.
25.
26.
AF-ON / AF-START / STAR ACCESS LEVER: This lever can be pull outward or inward to access both the AF-ON feature and the Star
customizable button, theses are important controls for video shooting and care should be taken to fully understand their working and subtleties.
TOP LCD WINDOW: displays essential camera operating data.
27
.
MOUNTING HOLE FOR ACCESSORY: a 1/4”-20 TPI hole is supplied to accept a TLC accessory or TLC base ball for mounting a
strobe arm or a modeling light.
28.
REMOVABLE VIEWFINDER: A full view of the illuminated camera viewfinder displays all necessary information.
This viewfinder be removed and replaced with optional Aqua View Finder for a larger displayed image.
page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS IN DETAIL, CONTINUED
MODE DIAL ACCESS KNOB: Rotate to select the proper shooting mode, C1, C2 and C3 can pre programmed with personal parameter
and care should be taken to understand the various combination available
29.
30.
AF POINT SELECTOR / MAGNIFIER BUTTON: Push to select the AF pattern desired or to magnify the image on the rear LCD,
Spot, Center Weighted or Matrix metering options.
31.
32.
33.
SET / MOVIE SHOOTING BUTTON Press to approve selection of menu or to engage the video recording mode.
ON/OFF & QUICK CONTRONL DIAL SWITCH LEVER: Rotate to turn on the camera and quick control dial
REAR WINDOW LCD: This port window allows viewing of the recorder images and is used in the Live View as well as the Video mode
for framing, a cutaway in the upper right corner allows the users to see the recording pilot light. Allow viewing of menus as well.
34.
35.
36.
37.
ERASE BUTTON: Press to delete images.
PLAYBACK BUTTON: Press to activate the monitor and review images.
INFO BUTTON: This button will activate the rear LCD and display all pertinent shooting information.
PICTURE STYLE BUTTON: Press to select the desired feature. (note: It is somewhat recommended to shoot in RAW format and
concentrate on these option in post production).
38.
39.
MENU BUTTON: Press to activate menu display, scroll using main or quick dial control knob and select using SET function button
LIVE VIEW ACTIVATING BUTTON: Press to engage the LIVE VIEW feature of your camera, this is the first step in setting up the camera
for video shooting.
40.
41.
RUBBER ANTI SKID PADS: Four rubber pads are provided to protect the housing and preventing it from sliding on wet decks.
SACRIFICIAL ANODES: (2X) zinc anodes are installed to protect your housing against salt water corrosion; theses are made to deteriorate
easier than the other strategic part of your housing, hence the name sacrificial anodes. These anodes need to be replaced by the user
as needed.
42.
43.
MOUNTING HOLES: Three 1/4” X 20 holes are provided for mounting strobes trays or accessories.
MOISTURE ALARM WARNING DIODE: Warning LED will light up in the unlikely event of water penetrating the housing.
page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
The Aquatica Pro Digital housing serie is issued from the world’s most technologically advanced underwater housing lineage, ergonomically
designed to place all the essential camera controls under your finger tips and features the following:
A.
B.
C.
D.
A port locking mechanism to prevent accidental rotation of the port or extension mounted on the housing
A Lens Lock Release control that will activate the lens release button of camera from the outside of the housing.
A quick release tray, allowing fast and easy removal of camera.
Large ergonomic and easy to operate controls for most of the manual and computerized
camera functions.
E.
F.
A flexible strobes connector circuitry that allows evolution according to ones needs.
The following controls can be easily manipulated or accessed underwater:
- Mechanical shutter release.
- Shutter speed through the Main-Command Dial
- Aperture through the Sub-Cmd Dial
- Focus / Zoom
- AE-L/AF-L & AF-ON and * (star) access
- LCD panel illumination & information display.
- Top LCD windows
- Metering system selector
- Exposure mode (Mode)
-.Exposure Compensation
- Focus Area Selector
- ISO sensitivity
- Delete button access
- Live view & Video recording access
G.
H.
A complete selection of bayonet mounted ports including an 6”, 8” and 9.25 diameter dome, two flat ports, various extension
rings to preserve the image quality of your EF mount lenses as well as various port adapter for other makes of housings.
A complete line of lens gears including Auto/Manual focus selector gears and related accessories.
PREPARATION OF THE HOUSING
1. Attach Grip Bracket to the housing:
The housing comes with two Grips for both right and left hand grips which should be installed on the sides of the housing with the
supplied screws and Allen key. Occasionally remove the grips and lubricate the screws (see Care and Maintenance: of the housing.)
Depending on which strobe system you are using, you can mount the necessary shoes or brackets onto the 1/4”-20 threaded holes on
the top of the hand grips. The AQUATICA TLC strobe arm system is recommended.
There are also three (3) 1/4”-20 threaded holes on the bottom of the housing that can be used for various mounting application trays or
tripod. As well there is another hole on top rear half of the housing for mounting accessories such as a video or focusing light.
Mount your strobe and connect the sync cord to the housing’s strobe bulkhead. Be sure to read the
section titled “Care and Maintenance: of the O-rings.”
2. Lubricate the Main O-ring Seal:
Before use, carefully inspect the Main O-ring seal from in its groove on the front half of the housing to confirm that it is free from
scratches or foreign material. Lubricate the O-ring with a light coat of silicone grease.
When replacing the O-ring place the entire O-ring over the O-ring groove and start by pushing the Oring in the corners. Work your way
around the O-ring making sure the O-ring is snugly sitting in the groove.
For proper handling and maintenance of O-rings be sure to read the section titled “Care and Maintenance: of the O-rings.”
page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION OF THE PORTS
1. Select the correct port:
Depending on whether you’ve decided to shoot macro or wide angle photography, you will be installing either a flat Macro Port (product
# 18426 or 18428), or a Dome Port (Product # 18405, 18407 or 18409). See lens chart for the suggest port and accessories.
Macro Port Extension Rings: If you intend to use a Macro lens you will require an additional extension ring. These extension rings fit
between the Macro Port and the housing to provide the extra space necessary for the longer lens.
Dome Port Extension Rings: When using a wide angle or zoom lens, the Dome Port may require the uses of an extension ring to
closely match the optical center of both the dome and the lens.
In order to reduce glare, maximize contrast and offer physical protection to the dome, the use of a dome shade is highly recommended.
See lens chart for the suggested dome shade.
A comprehensive list of the lenses supported and their required extensions and/or accessories is supplied at the end of this manual. For
the latest uptdated version of this lens chart, you can refer to the Lens Chart for the Aquatica 5D Mk II housing on www.aquatica.ca
2. Clean the port:
Dirt, grease or fingerprints on the port especially on the inside, can adversely affect the quality of the image. Acrylic ports should be
cleaned with plastic cleaner and the glass ports should be cleaned with lens cleaner. For more details be sure to read the section titled
“Care and Maintenance: of the Ports.”
3. Lubricate the port O-ring seal:
Before using the port, remove the O-ring on the rear of the port and lightly coat it with silicone grease. For more details be sure to read
the section titled “Care and Maintenance: of the O-rings.”
PREPARATION OF THE LENS
Depending on the lens used, there are a number of gear options possible. Using the right gear (s) and correctly mounting
them on the lens is very important for a smooth housing operation. Follow the installation directions included with each gears carefully.
The use of EF types lenses is mandatory.
A comprehensive list of the lenses supported and their required gears is supplied at the end of this manual. For the latest uptdated
version of this lens chart, you can refer to the Lens Chart on www.aquatica.ca
Notes: If the camera is set in manual focus a focus gear must be mounted on the lens. If you are using a zoom lens with a
zoom ring the camera must be on auto focus, also note that if using a dome port you may need to install a closeup diopter on the
lens to correct the minimum focusing distance of the lens so that it will be able to focus on the virtualimage created by the dome.
See lens chart for the suggested diopter, if required for your lens/port combination.
Gear installation:
Mount the focus gear over the focus ring of the lens.
(a) For Slip-on gears (gears without mounting screws): Slide the gear over the lens and align the gear with the front of the lens focusing ring.
(b) For gears with mounting screws:Tighten the three set screws evenly. Tighten each screw approximately ½ a turn working around the
gear until all the three (3) screws are tightened, and the gear is concentric with the lens body.
CAUTION: Do not over-tighten these screws, as this might bind the lens, thus restricting the rotation of the focus ring and/or damaging
the lens. Conversely under-tightening these screws might cause the gear to slip or loose alignment.
Rotate the focus ring several times to make sure it moves smoothly and the gear does not slip before closing the housing
WARNING: If the lens is a not of the USM type, never attempt to operate it with the camera in autofocus mode and with a mounted
focus gear engaged. This might cause serious damage to your camera or to the lens focusing motor.
Zoom lenses: When using a zoom lens, the gear should be mounted on the zoom lens control. The housing focus control then
becomes the zoom control. Focusing of lens is achieved by using the camera’s autofocus system.
page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA PREPARATION AND INSTALLATION
1.
Important Note: prior to installing the camera in the housing, remove the camera strap, “D” Clips and/or any object that might
obstruct installation or get in the way of that attach the strap should be removed or tucked away
3.
4.
Make sure the ON / OFF (key # 32) is in the ON position and that the lens lock lever is in the proper position
Remove the saddle from the housing and carefully place the camera on it and ensure
the camera is properly installed and aligned as follows:
a) The camera is properly aligned and secured against rotation or movement.
b) Align the Tripod Socket of the camera with the mounting screw. Tighten the
mounting screw securely while ensuring that the camera position is not altered.
set arresting block as per drawing at right.
c) Align the ON/OFF lever to the ON position
d) Slide the quick release tray back into place as per drawing at right.
CLOSING OF THE HOUSING
Once the camera is secure on the saddle inside the front half of the housing, simply:
1.
Slide the housing’s hot shoe connector onto the hot shoe base of the camera,
as seen in photo at right.
Before closing the housing always ensure that:
1.
2.
3.
4.
The main O-ring on the front half of the housing is clean,lubricated and properly seated for a positive seal.
The sealing surface on the rear half of the housing is clean and free from any scratches or physical damage.
All cords or wires are tucked in so that they do not interfere with the closing of the housing.
The ON/OFF lever is in the same position on both the camera and the housing .
To close the housing simply:
i.
Join the front and rear halves of the housing using the two dowel pins at the bottom of the housing as a guide.
ii.
Hold the housing with both hands and look around the sealing surface to ensure that the O-ring remained properly seated and
that no cords, wires or “D-rings” are caught between the edges.
iii.
Close the two sides latches simultaneously. Reverse the process to open housing
CAUTION: if you feel any resistance as you attempt to close the latches, do not force the closure. Check for an obstruction
and try again.
iv.
Verify that the safety locking mechanisms of the latches are properly engaged to avoid any accidental opening.
page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
LENS INSTALLATION
With the camera inside the housing, install the lens prepared with the gears through the port opening in the front of the
housing. Ensure that the lens mounted gears are properly installed and aligned. Rotate the focus / zoom control knob to
ensure that the gears are properly meshed, do not grind and that their rotation is smooth.
Note: To avoid damaging the auto-focus mechanism of the camera when using standard EF type lenses, you should
always set the Focus Control to “M” Manual for testing the proper meshing of a focusing gears. this procedure is not
required with USM type lenses.
CHANGING A LENS (REMOVING A LENS)
The lens mounted gears may restrict the view and ease of access to the lens release button of camera. The AQUATICA
Pro Digital Housing features a Lens Release Lever (key # 13) that is designed to trigger the lens release button of camera
to allow easy removal of lens.
To remove a lens, simply rotate Lens Release Lever (key # 13) to press the camera lens release, hold and turn the lens
clockwise.
MOUNTING THE PORT
Before mounting the Port on the Housing always ensure that the port O-ring is clean, lubricated and properly seated in its
groove and that he sealing surface on the Housing is clean and free of physical damage.
The AQUATICA Pro Digital Housing System features a locking bayonet mount (#17). To mount the port or extension ring
simply:
1. Place the housing on its back on a soft steady surface.
2. Place the port or extension ring inside the main port of the housing. Align one of the four alignment notches with the
opening of the housing.
3. Place your hands on opposite sides of the port or extension ring.
4. Push with even force on both sides of the port or extension ring until you feel it snap into place. Make sure the bayonet
is completely inside the housing.
5. Finally press the port lock button down, turn the Port clockwise
until it stops and then release the port lock button. Do not force it.
If there is too much resistance take the port off, check the O-ring
and retry.
6. Check to ensure for the proper seating and sealing of the port
or extension and that it is safely locked on the housing.
Note : It is recommended that you familiarize yourself with this
mount by trying it without the camera, this will allowyou to see
the inside view of the bayonet mount and of the ports or extension
rings in the housing.
page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNTING AND ATTACHING FLASHES
Depending on which strobe system you are using, you can mount the necessary shoes or brackets or Base Ball onto the
threaded holes on the top of the hand grips. Use of the Aquatica TLC Strobe Arm System is recommended.
There are also three 1/4”-20 threaded holes on the bottom of the housing that can be used for various mounting applica-
tions. For example, A mounting tray can be fitted on the bottom of the housing. A 1/4”-20 threaded hole on top of the rear
half of the housing will accept an Aquatica bracket or Base Ball that can hold a small dive light or a strobe arm.
Internal switch board circuit:
Your Aquatica 5D Mk II Pro Digital housing is supplied with two Nikonos type connectors which are in turn connected to a
switch board circuit. Optional Ikelite bulkheads connectors are also available.
When preparing the sync cord be sure to lubricate the O-ring on the sync cord’s connector with a light coat of Aquatica O-
ring lubricant, Also advisable is to put a light coat of O-ring lubricant on the threads of this connector.
Your Canon Digital camera design does not allow flashes to be connected directly to the camera and be used in eTTL in-
less they are original Canon flashes in third party housing with the required connector and cords.
On your housing you will find two bulkhead connectors, the main and secondary connectors are wired through a switch
board that will allow you to eventualy evolves as underwater strobes technology evolves. By default you housing is deliv-
ered with the switch board set to full manual, if the eTTL exposure is desired then it can be made in either of two methods:
1) By using a single flash from Canon or other brand (that is eTTL compatible with your camera) in a underwater housing
connected with a proper 6 pins TTL cord to a compatible 6 pins connectors on your Aquatica housing.
2) By using an external eTTL converter connected to a 6 pins connector on your Aquatica housing to which one or two
underwater strobes with compatible TTL cords are then connected to this converter, (check strobe and converter
manufacturer for compatibility).
Set up instruction for eTTL operation
Using the tip of a pen push the switches 1, 2, 3 & 4 to the ON (up) position, this will activate the connections on your main
6 pins bulkhead connector allowing eTTL communication between the camera and the housed flash or eTTL converter.
Set up instruction for manual operation
All switches must be in the OFF (lower) position, in this case all eTTL connections are disabled and only the ground and
sync are left active, this will allow two underwater strobes or housed flashes to be connected directly via the main and
secondary bulkhead.
page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
TAKING A PICTURE
Following are the basic techniques. For more information and advanced photography please study the Canon 5D Mk II
instruction manual.
NOTE *The quick and main dial control can access a wide range of modification to the current functions allowing the
users to conveniently position vital controls at their fingertip.
1.
Rotate the Mode dial knob (key # 29) and select the desired exposure mode the can be seen from the Top LCD
window (key # 22). Exposure Mode options in sequence are: Programmed AE (P), Shutter Priority AE (Tv),
Aperture Priority AE (Av) or Manual Exposure (M).
Note: When using a flash, it is reccomended that the camera be used only in Single Frame Motor Drive or
there is the possibillity that the camera will fire before the flash can recycle.
3.
Push the Metering Pattern Knob (key# 6) and select the metering system symbol you wish to use in the
LCD panel.
4.
5.
6.
Pull the Shutter Release Lever partially back. This will activate the camera’s meter and autofocus system.
If using manual focus use the Focus Knob (key # 10) on the housing or on the flat port to focus.
If using the Manual or Shutter mode adjust the main dial knob (key # 2) or Quick dial (key # 24) to set the
exposure.
7.
Pull the Shutter Release Lever (key # 1) the rest of the way until the camera fires.
Shooting tip:
The lever in the rear right portion of the housing (key #25) can be used to access the AF-ON and/or the * (star) buttons,
just pull outward or inward to access the desiresd one, theses two buttons can be modified to conform to your personal
style of image making, careful reading of the Canon 5D Mk II manual is recommended to pull the maximum out of theses
features
page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE HOUSING
Whenever changing ports or O-rings, it is highly advisable to perform a simple seal test without the camera inside. Strapping a weight to
the housing and lowering the unit to a depth of 30 to 50 feet of water for at least 10 minutes will assure you that the seating of the new
port or o-ring is proper. This test, though time consuming and often considered unnecessary, may save your camera equipment from
irreparable water damage.The housing is now ready for the dive.
CAUTION: Never jump into the water with the housing. It is best to have the system handed to you after you have made your entry, or
have it lowered to you on a rope. Make certain that ropes of other equipment stay clear of the system.
When photographing, be sure to respect the environment. Avoid damaging marine life or manipulating sea creatures to obtain a pleasing
photo. The housing is slightly negatively buoyant so that you can lay it down on the bottom, but avoid laying it on living coral or other
delicate marine life.
Changing the memory card
Always take care to thoroughly dry the housing before opening it to change memory card. Wipe the housing off with a dry towel. If
possible it is suggested that the housing be blown dried by directing an air nozzle around the main o-ring before opening.
Rest the housing on its front with the lens facing down, be carefull to protect the port surface, release the two side latches simultane-
ously. Lift the rear part of the housing and place it in a secure location. This minimizes the possibility of any residual water falling into
the housing and on to the camera when the housing is opened or damage to the sealing surface
.
TRANSPORTING THE AQUATICA Pro Digital housing
Store the AQUATICA Pro Digital housing in a sturdy, shock proof container. When travelling by air, remove or loosen the port. This al-
lows for equalization of the air pressure inside the housing to the external air pressure. Failure to do so may cause serious damage to
the acrylic ports. Avoid travelling with the camera mounted in the housing. If you must do so, remove the lens as external pressure can
damage the camera.
CARE AND MAINTENANCE
Of the housing:
After each and every salt water dive, your housing system should be soaked or rinsed in fresh water. The housing system should soak
in fresh water for at least 30 minutes. During this soaking period reach into the water and operate all the controls several times.
Be sure to remove the housing’s main o-ring and clean it after every use. Refer to Maintenance: Of the O-rings. To ensure that the hand
grips won’t fuse on to the housing due to the exposure to salt water, it is also a good practice to occasionally remove the hand grips.
Clean and lubricate the bolts with a small amount of WD-40.
WARNING: Use WD-40 carefully, sparingly and only on metal to metal surfaces. WD-40 can damage the acrylic on the ports, the
optical surfaces on lens as well as the O-rings.
Of the Ports:
Care should be taken with the Dome Port and Macro Port to avoid scratches on the lens surface. The acrylic port is softer than glass
so minor exterior scratches are often unavoidable. However, since the indices of refraction for acrylic and water are almost equal the
scratches will not seriously impair image quality. Internal scratches(air side) must be avoided as they do not fill in with water and will
affect the quality of the image.
Clean the dome using only products recommended for cleaning acrylic and a soft lint free cloth. Dust on the interior surfaces of the port
can be removed with a soft camel hair brush or a blower brush. Caution must be taken when using aerosol devices as not to spray the
lens material with the liquid propellant as this may seriously affect the optical properties of the port. Use of pressurize air from a dive
tank is not recommended, the force of the air stream may easily dislodge a port or O-ring, It is advisable that ports should be removed
and serviced after avery dive.
page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Of the Latches:
The two latches of the AQUATICA Pro Digital are designed to have a locking action to prevent accidental opening.Always
ensure that the locking mechanism is secure. Watch for the build-up of corrosion or salt residue around the latches. This
will appear as a white material. Lubricate the latches with a small amount of WD-40 to remove the corrosion
or salt residue build-up.
Of the O-Rings:
The O-rings that need to be maintained on a regular basis are the main housing O-ring and the O-ring on the lens port
The main O-ring should be cleaned on a daily basis and the port O-ring should be cleaned daily or each time the port is
changed.
Of the sacrificial anodes:
The two anodes attached to the bottom parts of the housing are there to prevent corrosion due to electrolysis, as time
goes they will deteriorates and need replacement, contact your dealer for replacement (parts # 19220).
TO SERVICE O-RINGS ON THE HOUSING MAIN O-RING, PORTS AND EXTENSION RINGS
1.
Remove the O-ring. It is important never to use a sharp instrument when removing an O-ring as this may damage
the O-ring groove or the O-ring itself. A bobby pin or edge of a credit card works well.
2.
Once the O-ring is removed, it should be examined for damage. Check to make sure that the O-ring is free of
nicks and cuts and that it retains its original round profile. O-rings that appear to be damaged should be discarded
immediately and replaced with new O-rings.
3.
4.
5.
6.
Rinse the O-ring with fresh water and dry it with a clean lint free cloth.
Clean the O-ring groove (where the O-ring sits) with a Q-tip. Be sure to remove any lint the Q-tip may leave
behind. Inspect the groove for damage.
Wipe the part of the housing that the O-ring seals against with a clean lint-free cloth.
Re-grease the O-ring with a thin layer of O-ring grease until it appears to be smooth and shiny. Do not over
grease it. Use just enough grease so the O-ring will pull smoothly through your fingers. Excessive amounts of
grease will only serve to attract dirt to the o-ring.
7.
Make sure that the O-ring is properly (envenly) installed in the O-ring groove.
8.
To reinstall the clean and lubricated O-ring, place the entire O-ring over the groove and start by pushing theO-ring
in at each corner then, push the O-ring at each side and finally, work in the rest of the O-ring. Never start at one
end and work your way around the O-ring. This places uneven tension on the O-ring which may cause the O-ring
to stretch resulting in excess O-ring, which will have no place to go.
There are internal O-rings on the housing controls as well. These O-rings are not as susceptible to damage as they are
not exposed but they do require yearly maintenance and are not user serviceable. The housing should be returned to
AQUATICA or to an authorized AQUATICA service facility for this annual maintenance. Check for the closest service cen-
An internal moisture alarm is installed in your AQUATICA Pro Digital housing (Product # 20023). This moisture alarm is
powered by an easily replaced CR 2032 battery. Please read the instruction sheet provided for your moisture alarm prior
to installing the battery.
page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOMMENDED AQUATICA ACCESSORIES
18407 9.25” GLASS DOME
18405 8” ACRYLIC DOME
18426 FLAT MACRO PORT
20054 AQUA VIEW FINDER
18409 6” ACRYLIC DOME
EXTENSION RINGS
18790 PORT REAR CAP
19216 HARD TRANSPORT CASE
FOR AQUA VIEW FINDER
18789 HOUSING BODY CAP
19300 BASIC REMOTE CONTROL
18480 8” DOME SHADE F.E.
18484 6” DOME SHADE F.E.
ZOOM & FOCUS GEARS
18480 8” DOME SHADE W.A..
MAINTENANCE & REBUILT
O-RING KITS
of our Technical Lighting Control line of strobe arms and supports.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
PLEASE READ CAREFULLY
One year Limited Warranty.
Thank you for purchasing an AQUATICA manufactured product! Your AQUATICA housing is handcrafted by a
small group of specially trained individuals - each of whom takes the most pride and satisfaction in offering you
the best underwater camera housings in the world. All AQUATICA products are guaranteed against defects in
material or workmanship for (1) one full year from the date of purchase for consumer use. these same products
when used commercially will carry a 90-day warranty. No statutory warranty applies. Camera housed inAQUATICA
housings are not covered under this warranty andANY WATER DAMAGE SUSTAINED DUE TO INSTALLATION
ERROR OR ANY OTHER REASON IS NOT THE RESPONSABILLITY OF AQUATICA. Therefore the appropriate
insurance should be maintained by the user.
Warranty does not apply to replaceable seals or damages to impacts or abrasive surfaces. Warranty applies
only to products purchased from authorized AQUATICA dealers and does not extend beyond the original retail
purchaser. Unauthorized modifications or repairs will automatically void this warranty. this applies to removal of
serial numbers and AQUATICA identification labels.
To obtain service during or after the warranty period you must notify AQUATICA at 514-737-9481
and ship BY REGISTERED MAIL (INSURED) ONLY, enclosing your proof of purchase to:
AQUATICA
3025 De Baene
Montreal (Quebec)
H4S 1K8
Mark clearly on your package “Canadian goods returned for repair”
Do not ship by any other means.
Unauthorized packages will be refused.
YOUR SERIAL NUMBER_______________________________
page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
|