PUB.DIM-618
Digital Video Camcorder
English
Instruction Manual
Camescope vidéo numérique
Françai
s
Manuel d’instruction
Videocámara digital
Español
Manual de Instrucciones
Digital
Video
Cassette
Mini
PUB. DIM-594
Please read also the following instruction
manuals.
DV Network Software
Instruction Manual (Installation and Preparation)
Version
2
E
F
Mode d’emploi (Installation et préparation)
Es
Manual de Instrucciones (Instalación
y
preparativos)
Veuillez lire aussi les modes d’emploi
suivants.
Lea también los manuales de instrucciones
siguientes.
This manual covers the installation and the connection procedures only.
For more operating instructions, refer to the PDF format manual provided
on the DIGITAL VIDEO SOLUTION DISK For Windows.
Ce manuel traite uniquement des procédures d’installation et de connexion.
Pour les instructions d’utilisation, reportez-vous au manuel au format PDF
fourni sur le disque DIGITAL VIDEO SOLUTION DISK For Windows.
Este manual solamente cubre los procedimientos de instalación
y
conexión.
Para más instrucciones de operación, consulte el manual en formato PDF
contenido en el disco DIGITAL VIDEO SOLUTION DISK For Windows.
®
This software is for use with Windows XP only.
Ce logiciel ne peut être employé que sous Windows® XP.
Este software solamente es compatible con Windows® XP.
• Digital Video Software
• DV Network Software
NTSC
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Usage Instructions
WARNING:
E
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING
INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY.
COPYRIGHT WARNING:
Unauthorized recording of copyrighted materials may infringe on the rights of
copyright owners and be contrary to copyright laws.
Digital Video Camcorder, ZR90/ZR85/ZR80 systems
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and use in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual.
If such changes or modifications should be made, you could be required to stop operation of the equipment.
Canon U.S.A. Inc.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
Tel No. (516)328-5600
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
Important Warning
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
the product’s enclosure, that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
The exclamation point, within an
equilateral triangle, is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the product.
SERVICE PERSONNEL.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
In these safety instructions the word “product”
refers to the Canon Digital Video Camcorder
ZR90/ZR85/ZR80 A and all its accessories.
10. Power Sources — The CA-570 Compact
Power Adapter should be operated only
from the type of power source indicated on
the marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
E
1. Read Instructions — All the safety and
operating instructions should be read
before the product is operated.
company. Regarding other power sources
such as battery power, refer to instructions
in this manual.
2. Retain Instructions — The safety and
operating instructions should be retained
for future reference.
11. Polarization — The CA-570 Compact Power
Adapter is equipped with a polarized 2-
prong plug (a plug having one blade wider
than the other).
3. Heed Warnings — All warnings on the
product and in the operating instructions
should be adhered to.
The 2-prong polarized plug will fit into the
power outlet only one way. This is a safety
feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug.
If the plug still fails to fit, contact your
electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the
polarized plug.
4. Follow Instructions — All operating and
maintenance instructions should be
followed.
5. Cleaning — Unplug this product from the
wall outlet before cleaning. Do not use
liquid or aerosol cleaners. The product
should be cleaned only as recommended in
this manual.
12. Power Cord Protection — Power cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them. Pay particular
attention to plugs and the point from
which the cords exit the product.
6. Accessories — Do not use accessories not
recommended in this manual as they may
be hazardous.
7. Avoid magnetic or electric fields — Do not
use the camera close to TV transmitters,
portable communication devices or other
sources of electric or magnetic radiation.
They may cause picture interference, or
permanently damage the camera.
13. Outdoor Antenna Grounding — If an
outside antenna is connected to the
product, be sure the antenna is grounded
so as to provide some protection against
voltage surges and built-up static charges.
Section 810 of the National Electrical Code,
ANSI / NFPA No. 70—1984, provides
information with respect to proper
8. Water and Moisture — Hazard of electric
shock — Do not use this product near
water or in rainy/moist situations.
grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of
grounding conductors, location of antenna
discharge unit, connection to grounding
electrodes, and requirements for the
grounding electrode. See figure 1.
9. Placing or Moving — Do not place on an
unstable cart, stand, tripod, bracket or
table. The product may fall, causing serious
injury to a child or adult, and serious
damage to the product.
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart combination to
overturn.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Damage Requiring Service — Disconnect
this product from the wall outlet and all
power sources including battery, and refer
servicing to qualified service personnel
under the following conditions:
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
Fig. 1
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
a. When the power-supply cord or plug is
damaged.
ANTENNA
DISCHARGE
UNIT
(NEC SECTION
810-20)
b. If any liquid has been spilled onto, or
objects have fallen into, the product.
c. If the product has been exposed to rain
or water.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE
GROUNDING ELECTRODE
SYSTEM
(NEC ART 250. PART H)
NEC - NATIONAL ELECTRICAL CODE
d. If the product does not operate normally
even if you follow the operating
instructions. Adjust only those controls
that are covered by the operation
instructions. Improper adjustment of
other controls may result in damage and
will often require extensive work by a
qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
14. Lightning — For added protection of this
product during a lightning storm, or when
it is left unattended and unused for long
periods of time, disconnect it from the wall
outlet and disconnect the antenna. This will
prevent damage to the product due to
lightning and power-line surges.
15. Overloading — Do not overload wall outlets
and extension cords as this can result in a
risk of fire or electric shock.
f. When the product exhibits a distinct
change in performance. This indicates a
need for service.
16. Objects and Liquid Entry — Never push
objects of any kind into this product
through openings as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Be careful not to spill liquid of any kind
onto the product.
19. Replacement Parts — When replacement
parts are required, be sure the service
technician has used replacement parts that
are specified by Canon or that have the
same characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock or other hazards.
17. Servicing — Do not attempt to service this
product yourself as opening or removing
covers may expose you to dangerous
voltage or other hazards. Refer all servicing
to qualified service personnel.
20. Safety Check — Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in safe
operating order.
When replacement of power supply is required, please return it to the
responsible nearest Canon Service Center and please replace it with the same
type number CA-570.
The Adapter can be used with a power supply between 100 and 240 V AC.
For areas where 120 V AC power is not used, you will need a special plug
adapter. Contact your nearest Canon Service Center for further information.
Use only CSA/UL Certified power supply cord set, Polarized, Type SPT-2 or
heavier, minimum No. 18 AWG copper, rated 125 or 250 V, minimum ‚P A,
minimum 6 ft (1.8 m), maximum 10 ft (3 m) long.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Using this Manual
Thank you for purchasing the Canon ZR90/ZR85/ZR80. Please read this manual
carefully before you use the camcorder and retain it for future reference.
E
Change the display language before you begin (
76).
Symbols and References Used in This Manual
❍
: Precautions related to the camcorder operation.
❍
❍
: Additional topics that complement the basic operating procedures.
: Reference page number.
❍ Capital letters are used to refer to buttons on the camcorder or the wireless controller
(ZR90/ZR85).
❍ [ ] are used to refer to menu items displayed on the screen.
❍ “Screen” refers to the LCD and the viewfinder screen.
❍ Please note that the illustrations mainly refer to the ZR90.
Setting the Time Zone, Date and Time
Set the time zone, date and time when you first start using your camcorder, or when
you have replaced the backup battery.
E
Setting the Time Zone/Daylight Saving Time
Operating modes (see below)
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
Menu item and its default setting.
(
39)
1. Press the MENU button to open the menu.
2. Turn the SET dial to select [SYSTEM] and press the
SET dial.
Button and switches to be operated
3. Turn the SET dial to select [T.ZONE/DST] and press
the SET dial.
The time zone setting appears (see table on the next page). The default setting is New
Operating Mode
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
POWER Switch
CAMERA
PLAY (VCR)
CAMERA
TAPE/CARD Switch
b (TAPE)
b (TAPE)
(CARD)
PLAY (VCR)
(CARD)
Shaded area : ZR90/ZR85 only.
: Function can be used in this mode.
: Function cannot be used in this mode.
CAMERA
CAMERA
Trademark Acknowledgements
• Canon and Bubble Jet are registered trademarks of Canon Inc.
• D is a trademark.
•
is a trademark.
• Windows® is either a registered trademark or trademark of Microsoft Corporation in the United States
and/or other countries.
• Macintosh and Mac OS are trademarks of Apple Computer, Inc., registered in the United States and
other countries.
• Other names and products not mentioned above may be registered trademarks or trademarks of their
respective companies.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Introduction
Important Usage Instructions ........................................................................................2
Important Safety Instructions........................................................................................3
Using this Manual ..........................................................................................................5
Checking Supplied Accessories......................................................................................8
Components Guide ........................................................................................................9
Basic Functions
Preparations
Preparing the Power Supply........................................................................................13
Loading/Unloading a Cassette ....................................................................................16
Installing the Backup Battery ......................................................................................17
Preparing the Camcorder ............................................................................................18
Using the Wireless Controller ............................................................20
Setting the Time Zone, Date and Time......................................................................21
Recording
Recording Movies on a Tape ......................................................................................24
Recording Still Images on a Tape................................................................................29
Zooming ........................................................................................................................30
Tips for Making Better Videos ....................................................................................32
Playback
Playing Back a Tape ......................................................................................................33
Adjusting the Volume ..................................................................................................35
Playing Back on a TV Screen........................................................................................36
Advanced Functions
Menus and Settings ......................................................................................................39
Recording
Using the Recording Programs....................................................................................46
Using the Night Modes ................................................................................................49
Skin Detail Function......................................................................................................50
Adjusting the AE Shift..................................................................................................51
Adjusting the Focus Manually ....................................................................................52
Setting the White Balance ..........................................................................................54
Setting the Shutter Speed............................................................................................56
Using the Self-Timer......................................................................................................58
Changing the Recording Mode (SP/LP)......................................................................59
Audio Recording ..........................................................................................................60
Using Digital Effects......................................................................................................62
Playback
Magnifying the Image..................................................................................................69
Displaying the Data Code ............................................................................................70
End Search......................................................................................................................72
Returning to a Pre-marked Position..................................................73
Photo Search/Date Search ..................................................................74
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Customizing the Camcorder........................................................................................75
Changing the Display Language ................................................................................76
Changing the Remote Sensor Mode ................................................77
Other Camcorder Settings ..........................................................................................78
E
Editing
Recording to a VCR or Digital Video Device ............................................................80
Recording from Analog Video Devices (VCR, TV or Camcorder) ..........................82
Recording from Digital Video Devices (DV Dubbing)..............................................83
Converting Analog Signals into Digital Signals (Analog-Digital Converter) ........84
Replacing Existing Scenes (AV Insert) ................................................86
Audio Dubbing ....................................................................................88
Connecting to a Computer Using a DV (IEEE1394) Cable ......................................91
Using a Memory Card
Inserting and Removing a Memory Card ..................................................................92
Selecting the Image Quality/Size ................................................................................93
File Numbers ..................................................................................................................95
Recording Still Images on a Memory Card................................................................96
Reviewing a Still Image Right after Recording ......................................................100
Recording Motion JPEG Movies on a Memory Card..............................................101
Selecting the Focusing Point ....................................................................................103
Recording Panoramic Images (Stitch Assist Mode) ................................................104
Playing Back a Memory Card ....................................................................................106
Protecting Images ......................................................................................................109
Erasing Images ............................................................................................................110
Combining Images (Card Mix) ..................................................................................111
Copying Still Images....................................................................................................115
Formatting a Memory Card ......................................................................................117
Connecting to a Computer Using a USB Cable ......................................................118
Creating a Start-up Image ........................................................................................119
Direct Printing
Printing Still Images....................................................................................................120
Selecting the Print Settings (Paper/Style) ................................................................123
Printing with Print Order Settings............................................................................126
Additional Information
Screen Displays ............................................................................................................128
List of Messages ..........................................................................................................131
Maintenance/Others ..................................................................................................134
Troubleshooting ..........................................................................................................140
System Diagram ........................................................................................................143
Optional Accessories ..................................................................................................144
Specifications ..............................................................................................................147
Index ............................................................................................................................149
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Supplied Accessories
Lens Cap and Lens
Cap Cord
Lithium Button
Battery CR1616
SS-900 Shoulder Strap BP-508 Battery Pack
CA-570 Compact
Power Adapter
(incl. power cord)
STV-250N Stereo
Video Cable
WL-D82 Wireless
Controller
Two AA (R6) Batteries SDC-8M SD Memory
Card (containing
IFC-300PCU USB Cable
sample images)
DIGITAL VIDEO
SOLUTION DISK
For Windows
For Macintosh
WA-30.5 Wide
Attachment
The serial number of this product can be found on the underside of the viewfinder.
Write down the number and other information here and retain this book as a
permanent record of your purchase to aid identification in case of theft.
Date of Purchase:
Purchased From:
Dealer Address:
Dealer Phone No.:
Model Name: ZR90/ZR85/ZR80 A
Serial No.:
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Components Guide
ZR90/ZR85/ZR80
E
REC SEARCH + button ( 28) /
(fast forward) button ( 34) /
CARD + button* ( 106)
FOCUS button ( 52) /
(play/pause) button ( 33)
REC SEARCH
–
button ( 28) /
NIGHT MODE button ( 49) /
(stop) button ( 33)
(record review) button ( 28) /
(rewind) button ( 33) /
CARD
–
button
*
(
106)
OPEN button ( 24)
Built-in speaker( 35)
LCD screen ( 24)
BATT. RELEASE button ( 13)
Backup battery
compartment ( 17)
Battery attachment unit
(
13)
Program selector ( 47)
Easy recording
Program AE
Memory card slot* ( 92)
DC IN terminal ( 13)
MENU button ( 39)
SET dial ( 39)
CHARGE indicator ( 13) /
DIGITAL EFFECTS
button ( 65)
Card access indicator* ( 96)
DIGITAL EFFECTS
ON/OFF button ( 65)
AE SHIFT/
END SEARCH
(self-timer)
AE SHIFT button ( 51) /
END SEARCH button ( 72)
button ( 58) /
DATA CODE
button ( 70)
/OFF
CARD MIX button* ( 112) /
(stitch assist) button* ( 104) /
SLIDE SHOW button* ( 107) /
REC PAUSE button ( 82)
CARD MIX /
SLIDE SHOW /
REC PAUSE
/
* ZR90/ZR85 only.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dioptric adjustment
lever ( 18)
PHOTO button ( 29, 96)
Accessory shoe ( 145)
Serial number
Viewfinder protect
cover ( 135)
Zoom lever ( 30)
Viewfinder ( 18)
TAPE/CARD switch*( 5)
Using a tape
b
Using a memory card
Strap mount ( 19)
Start/stop button
(
24, 101)
Grip belt ( 18)
Strap mount ( 19)
Power switch ( 5)
ER
W
POWER
CAMERA
OFF
CAMERA
Cassette compartment ( 16)
FF
O
CR)
(VCR)
PLAY
PLAY(VCR)
Cassette compartment
cover ( 16)
* ZR90/ZR85 only.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Terminal cover
Assist lamp (White LED)**
(
49)
Remote sensor*( 20)
Stereo microphone ( 60)
Terminal cover
S-video terminal**( 37)
S
DV
DV terminal ( 80, 91)
AV terminal ( 36) /
(phones) terminal
(
35, 61)
Bottom view
USB terminal*( 118, 120)
OPEN/EJECT 5 switch
(
16)
Tripod socket ( 32)
* ZR90/ZR85 only.
** ZR90 only.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
WL-D82 Wireless Controller
!
!
@
q
w
e
START
/STOP
ZOOM
r
t
W
T
PHOTO
@
SELF T. D.EFFECTS
MENU
SET
@
@
@
y
u
i
ON/OFF
TV SCREEN
DATA CODE SLIDE SHOW
CARD
@
@
@
@
@
SEARCH SELECT
ZERO SET
o
!
REW
PLAY
STOP
SLOW
FF
MEMORY
12bit
AUDIO OUT
!
!
!
AUDIO DUB. PAUSE
2
AV INSERT AV DV REMOTE SET
REC
#
#
PAUSE
-
WIRELESS CONTROLLER WL D82
!
!
!
!
Zoom buttons ( 30)
Select buttons ( 39)
REMOTE SET button ( 77)
Transmitter
!
!
!
@
@
@
@
@
@
@
@
@
@
#
#
q
w
e
r
t
y
u
i
PHOTO button ( 29, 96)
START/STOP button ( 24, 101)
SELF T. button ( 58)
MENU button ( 39)
SET button ( 39)
CARD
SLIDE SHOW button ( 107)
REW button ( 33)
PLAY button ( 33)
buttons ( 106)
D. EFFECTS button, ON/OFF button ( 65)
TV SCREEN button ( 128)
DATA CODE button ( 70)
74)
o -/+ buttons (
FF
button ( 34)
button ( 34)
SEARCH SELECT button ( 74)
!
ZERO SET MEMORY button ( 73)
STOP button ( 33)
button ( 34)
!
12bit AUDIO OUT button ( 89)
!
AUDIO DUB. button ( 88)
PAUSE button ( 34)
SLOW button ( 34)
2 button ( 34)
!
REC PAUSE button ( 82)
!
AV INSERT button ( 86)
!
AV DV button ( 84)
!
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the Power Supply
Attaching the Battery Pack
1. Turn the POWER switch to OFF.
2. Move the viewfinder upward.
3. Attach the battery pack to the
camcorder.
E
q
w
ER
W
PO
CA
FF
RA
ME
O
)
CR
Y
(V
A
PL
• Remove the terminal cover of the battery
pack.
• Press lightly and slide it in the direction of
the arrow until it clicks.
e
Charging the Battery Pack
1. Connect the power cord to the
adapter.
DC IN terminal
2. Plug the power cord into a power
outlet.
DC IN 8.4V
CHARGE
indicator
3. Connect the power adapter to the
camcorder’s DC IN terminal.
CARD/CHARGE
The CHARGE indicator starts flashing. It
e
glows steadily when charging is complete.
q
4. When charging is complete,
disconnect the power adapter from
the camcorder. Unplug the power
cord from the power outlet and
w
disconnect it from the adapter.
5. Remove the battery pack after use.
Press the BATT. RELEASE button to remove the battery.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using a Household Power Source
1. Turn the POWER switch to OFF.
2. Connect the power cord to the
power adapter.
q
ER
W
PO
RA
ME
CA
OFF
)
CR
(V
PLAY
3. Plug the power cord into a power
outlet.
4. Connect the power adapter to the
camcorder’s DC IN terminal.
r
w
e
❍ Turn off the camcorder before connecting or disconnecting the power adapter.
❍ If the adapter is used close to a TV, it may cause picture interference. Move the
adapter away from the TV or the antenna cable.
❍ Do not connect any products that are not expressly recommended to the
camcorder’s DC IN terminal or to the power adapter.
❍ You may hear some noise from the power adapter during use. This is not a
malfunction.
❍ Do not disconnect and reconnect the power cord while charging a battery
pack. The battery pack may not be charged correctly even if the CHARGE
indicator glows steady. The battery pack may also not be charged correctly
when a power outage occurs during charging. Remove the battery pack and
attach it back to the camcorder.
❍ The battery pack may be defective when the CHARGE indicator flashes rapidly.
❍ The CHARGE indicator informs you about the charge status.
0-50%:
More than 50%: Flashes twice every second
100%: Glows steadily
Flashes once every second
❍ Charging, Recording and Playback Times
Below times are approximate and vary according to the charging, recording or
playback conditions.
BP-508
BP-512/
BP-511
BP-514
BP-522
BP-535
(Supplied) (Optional) (Optional) (Optional) (Optional)
Charging Time
110 min. 120 min. 150 min. 210 min. 310 min.
Max. Recording Viewfinder 125 min. 225 min. 260 min. 455 min. 730 min.
Time LCD 85 min. 155 min. 180 min. 320 min. 520 min.
Typical Recording Viewfinder 65 min. 125 min. 145 min. 255 min. 405 min.
Time*
Playback Time
LCD
45 min. 85 min. 100 min. 175 min. 280 min.
90 min. 170 min. 195 min. 345 min. 550 min.
* Approximate times for recording with repeated operations such as start/stop, zooming,
power on/off. Actual time may be shorter.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
• Charge the battery pack in temperatures between 41 ºF and 104 ºF (5 ºC
and 40 ºC).
• A lithium ion battery pack can be charged at any charge state. Unlike
conventional battery packs, you do not need to completely use or discharge
it before charging.
E
• We recommend that you prepare battery packs 2 to 3 times longer than you
think you might need.
• To conserve battery charge, turn off the camcorder instead of leaving it in
record pause mode.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading/Unloading a Cassette
Use only videocassettes marked with the D logo.
1. Slide and hold the OPEN/EJECT
switch and open the cassette
compartment cover.
w
Tape protection tab
q
The cassette compartment opens
automatically.
2. Load/unload the cassette.
• Load the cassette with the window facing
the grip belt.
• Unload the cassette by pulling it straight
out.
e
3. Press the P mark on the cassette
compartment until it clicks.
4. Wait for the cassette compartment to
retract automatically and close the
cassette compartment cover.
r
❍ Do not interfere with the cassette compartment while it is opening or closing
automatically, or attempt to close the cover before the cassette compartment
has fully retracted.
❍ Be careful not to get your fingers caught in the cassette compartment cover.
If the camcorder is connected to a power source, cassettes can be loaded/
unloaded even if the POWER switch is set to OFF.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Backup Battery
The backup battery allows the camcorder to retain date, time (
21) and other
E
camcorder settings while the power source is disconnected. Power the camcorder from
a household power source when replacing the backup battery to retain the settings.
1. Open the backup battery cover.
e
w
q
2. Insert the lithium battery with the
+ side facing outward.
3. Close the cover.
WARNING!
• The battery used in this device may present a fire or chemical burn hazard if
mistreated. Do not recharge, disassemble, heat above 212 °F (100 °C) or
incinerate the battery.
• Replace the battery with a CR1616 made by Panasonic, Hitachi Maxell, Sony,
Toshiba, Varta or Renata. Use of other batteries may present a risk of fire or
explosion.
❍ Do not pick up the battery using tweezers or other metal tools as this will
cause a short circuit.
❍ Wipe the battery with a clean dry cloth to ensure proper contact.
❍ Keep the battery out of reach of children. If it is swallowed, seek medical
assistance immediately. The battery case may break and the battery fluids may
damage stomach and intestines.
❍ Do not disassemble, heat or immerse the battery in water to avoid the risk of
explosion.
The backup battery has a life span of about a year. j flashes in red to inform
you that it needs to be replaced.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing the Camcorder
Adjusting the Viewfinder (Dioptric Adjustment)
1. Turn on the camcorder and keep
the LCD panel closed.
2. Pull out the viewfinder.
3. Adjust the diopter adjustment
lever.
Attaching the Lens Cap
1. Attach the cord to the lens cap.
2. Pass the grip belt through the loop
with the metal fitting on the cord.
Press the buttons on the lens cap when
attaching/removing it. Hook the lens cap on
the grip belt while you are recording, and
place it over the lens when you have
finished.
Metal fitting
Fastening the Grip Belt
Hold the camcorder with your right
hand and adjust the belt with your
left.
Adjust the grip belt so that you can reach the
zoom lever and photo button with your index
finger, and the start/stop button with your
thumb.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Shoulder Strap
Pass the ends through the strap mount and adjust the length of the strap.
E
SS-900
Shoulder strap
Mounting the Wide Attachment
The WA-30.5 Wide Attachment gives you a wide perspective for indoor shots or
panoramic views (0.6×). The wide attachment is for use at maximum wide-angle.
Screw the wide attachment fully into
the lens filter thread.
❍ Do not look directly at the sun or other strong light sources through the wide
attachment. It could damage your eyesight.
❍ If you zoom to telephoto, the picture will not be in focus.
❍ The wide attachment may obstruct the remote sensor (the range of the
wireless controller narrows), or may cause a shadow to appear on the picture
when recording with a video light or the assist lamp (White LED).
❍ Filters cannot be used with the wide attachment.
❍ If dust accumulates on the wide attachment or on the camcorder lens, clean
both lenses gently with a blower brush.
❍ Do not touch the lens to avoid smudges and fingerprints.
❍ Do not store the wide attachment in a humid place as it may mold.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Wireless Controller
Point it at the camcorder’s remote
sensor when you press the buttons.
Inserting Batteries
The wireless controller operates with two AA (R6) batteries.
1. Open the battery cover.
2. Insert the batteries following the +
and – markings.
Replace both batteries.
3. Close the battery cover.
❍ Camcorder and wireless controller are equipped with 2 remote sensor modes
(
77). If the wireless controller does not work, check if camcorder and
wireless controller are set to the same mode.
❍ The wireless controller may not work properly when the remote sensor is
subjected to strong light sources or direct sunlight.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Time Zone, Date and Time
Set the time zone, date and time when you first start using your camcorder, or when
you have replaced the backup battery.
E
Setting the Time Zone/Daylight Saving Time
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
SYSTEM
T.ZONE/DST•••N.Y.
(
39)
1. Press the MENU button to open the menu.
2. Turn the SET dial to select [SYSTEM] and press the
SET dial.
3. Turn the SET dial to select [T.ZONE/DST] and press
the SET dial.
The time zone setting appears (see table on the next page). The default setting is New
York.
4. Turn the SET dial to select the setting option that represents your time
zone and press the SET dial.
To adjust for daylight saving time, select the time zone with the U next to the area.
Setting the Date and Time
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
D/TIME SET•••JAN. 1,2004
12:00 PM
SYSTEM
(
39)
5. Turn the SET dial to select [D/TIME SET] and press
the SET dial.
The year display starts to flash.
6. Turn the SET dial to select the year, and press the
SET dial.
• The next part of the display starts flashing.
• Set the month, day, hours and minutes in the same way.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Press the MENU button to close the menu and to
start the clock.
16
1
4
20
19
2
18
24
3
17
6
7
9
10
15
8
5
21
23
14
12
22
11
13
14 15 16 17 18 19 20 21 22 23 24
1
2
3
4
5
6
7
8
9
10 11 12 13
No.
No.
Time zone
LONDON
PARIS
Time zone
WELLGTN (Wellington)
SAMOA
CAIRO
HONOLU. (Honolulu)
ANCHOR. (Anchorage)
L.A. (Los Angeles)
DENVER
MOSCOW
DUBAI
KARACHI
DACCA
CHICAGO
BANGKOK
H. KONG (Hong Kong)
TOKYO
N.Y. (New York)
CARACAS
RIO (Rio de Janeiro)
SYDNEY
SOLOMON
FERNAN. (Fernando de Noronha)
AZORES
Once you have set time zone, date and time, you do not need to reset the clock
each time you travel to another time zone. Just set the time zone to the one of
your destination, and the camcorder automatically adjusts the clock.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Date and Time during Recording
You can display the date and time in the lower left corner of the screen.
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
E
DISPLAY SETUP/
D/T DISPLAY••OFF
(
39)
1. Press the MENU button to open the menu.
2. Turn the SET dial to select [DISPLAY SETUP/ ] and
press the SET dial.
3. Turn the SET dial to select [D/T DISPLAY] and press
the SET dial.
4. Turn the SET dial to select [ON].
5. Press the MENU button to close the menu.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Movies on a Tape
Before You Begin Recording
Make a test recording first to check if the camcorder operates correctly. Before you
make important recordings, clean the video heads (
135).
Recording
1. Remove the lens cap.
2. Set the camcorder to CAMERA
mode.
q
•
Set the POWER switch to
CAMERA and the TAPE/CARD switch to
b.
w
•
Set the POWER switch to
CAMERA.
R
E
W
O
P
A
ER
M
CA
FF
O
)
CR
(V
PLAY
3. Push the OPEN button at the LCD
panel and open the LCD panel.
4. Press the start/stop button to
begin recording.
r
POWER
A
ER
M
CA
FF
O
)
CR
(V
AY
PL
Press the start/stop button again to pause
recording.
e
When You Have Finished Recording
1. Turn the POWER switch to OFF.
2. Close the LCD panel and return the viewfinder into its initial position.
3. Replace the lens cap.
4. Unload the cassette.
5. Disconnect the power source.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ Wait until the tape counter stops completely before you start recording.
❍ When you do not remove the cassette, you can record the next scene without
producing any noise or blank sections between the recordings even if you turn
the camcorder off.
❍ Bright light may make it difficult to use the LCD screen. In such case, use the
viewfinder instead.
E
❍
You can rotate the LCD panel. Make sure to open
the LCD panel at 90 degrees before rotating it.
❍ When recording near loud sounds (such as fireworks, drums or concerts),
sound may become distorted or may be recorded not in the actual sound level.
❍ The camcorder will shut off after 5 minutes when left in record pause
mode to protect tape and video heads. “
AUTO POWER OFF” appears
20 seconds before shutoff. To continue recording, turn the POWER
switch to OFF and then back to CAMERA.
❍ About the LCD and viewfinder screen: The screens are produced with
extremely high-precision manufacturing techniques, with more than
99.99% of the pixels operating to specification. Less than 0.01% of the
pixels may occasionally misfire or appear as black or green dots. This
has no effect on the recorded image and does not constitute a
malfunction.
Allowing the Subject to Monitor the LCD Screen
You can rotate the LCD panel so that the screen faces in the
same direction as the lens. The viewfinder switches on
allowing you to use the viewfinder while the subject can
monitor the screen.
The image appears mirror reversed (LCD MIRROR ON).
However, you can choose to display the image as it is being
recorded (LCD MIRROR OFF).
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
LCD MIRROR•••ON
DISPLAY SETUP/
(
39)
1. Press the MENU button to open the menu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Turn the SET dial to select [DISPLAY SETUP/ ] and
press the SET dial.
3. Turn the SET dial to select [LCD MIRROR] and press
the SET dial.
4. Turn the SET dial to select [OFF].
5. Press the MENU button to close the menu.
When [LCD MIRROR] is set to [ON], only tape (ZR90/ZR85: or card) operation and
self-timer displays appear on the LCD screen (all displays appear on the viewfinder
screen).
Adjusting the Brightness of the LCD Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
–
+
BRIGHTNESS•••
DISPLAY SETUP/
(
39)
1. Press the MENU button to open the menu.
2. Turn the SET dial to select [DISPLAY SETUP/ ] and
press the SET dial.
3. Turn the SET dial to select [BRIGHTNESS] and press
the SET dial.
4. Turn the SET dial to adjust the brightness level.
5. Press the MENU button to close the menu.
Changing the brightness of the LCD screen does not affect that of the viewfinder
or the recordings.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Displays during Recording
e Remaining battery charge
E
q
w
e
r
The battery symbol indicates the charge
status of the battery pack.
t
• k starts flashing in red when the
battery pack is empty.
• When you attach an empty battery
pack, the power may turn off without
displaying k.
• The actual battery charge may not be
indicated accurately depending on the
condition under which battery pack
and camcorder are used.
q Time code
Indicates the recording time in hours,
minutes and seconds.
r When j flashes
w Remaining tape
j flashes in red when the lithium
button battery is not installed, or when
it runs out.
Indicates the remaining time of the tape
in minutes. b END flashes when the
tape reaches the end.
• When the time left is less than 15
seconds, the remaining tape time may
not appear.
• Depending on the type of the tape,
the indication may not be displayed
correctly.
t Recording reminder
The camcorder counts from 1 to 10
seconds when you start recording. This
is helpful to avoid scenes that are too
short.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching and Reviewing when Recording
REC SEARCH – button/
v (record review) button
REC SEARCH + button
Record Review
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
In record pause mode, this function allows you to review the last few seconds of your
recording to check if it has been recorded properly.
Press and release the c (record review) button.
The camcorder rewinds the tape, plays back the last few seconds,
and returns to record pause mode.
Record Search
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
In record pause mode, this function allows you to play back the tape (forward or
reverse) to locate the point where you wish to begin recording.
Press and hold the REC SEARCH + button (forward) or –
button (reverse).
CARD
• Release the button at the point you wish to begin recording.
• The camcorder returns to record pause mode.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Still Images on a Tape
E
PHOTO button
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
1.
Open the menu and select [CAMERA
SETUP]. Select [PHOTO REC], confirm that [TAPE b]
is selected and close the menu.
2. Press the PHOTO button halfway.
• F appears in green. If it does not appear in green, adjust the
focus with the SET dial.
• Exposure is locked.
•
When you press the PHOTO button on the
wireless controller, recording starts immediately.
3. Press the PHOTO button fully.
• F disappears.
• The camcorder records the still image for approx. 6 seconds.
During this time, the camcorder displays the still image and
keeps recording the sound.
• The camcorder returns to record pause mode.
❍ You can also record a still image while you are recording a movie by pressing
the PHOTO button fully.
❍
Starting your recording with a still image allows you to easily
locate the beginning of the recording with the Photo Search function ( 74).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Zooming
The camcorder automatically switches between optical zooming and digital zooming.
Image resolution is slightly lower with the digital zoom.
Zoom in
T
W
Zoom out
Zoom lever
MENU button
SET dial
Optical Zoom
22× optical zoom
20× optical zoom
PLAY (VCR)
18× optical zoom
CARD PLAY
CAMERA
CARD CAMERA
Move the zoom lever toward W to zoom out (wide-
angle). Move it toward T to zoom in (telephoto).
Press the zoom lever slightly for a slow zoom. Press harder for a
faster zoom.
You can also use the T and W buttons on the wireless controller.
However, you cannot control the zoom speed.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Zoom
88×/440× digital zoom
(88× in CARD CAMERA mode) (80× in CARD CAMERA mode)
80×/400× digital zoom
72×/360× digital zoom
E
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
CAMERA SETUP
D.ZOOM•••••••88X
(
39)
1. Press the MENU button to open the menu.
2. Turn the SET dial to select [CAMERA SETUP] and
press the SET dial.
3. Turn the SET dial to select [D.ZOOM] and press the
SET dial.
4. Turn the SET dial to select a setting option.
5. Press the MENU button to close the menu.
❍ Digital zoom cannot be used in the Night modes.
❍ Digital zoom cannot be used when the multi-image screen is selected.
❍ A zoom indicator appears for 4 seconds. It extends in light blue when the
digital zoom is set to 88× (ZR90), 80× (ZR85) or 72× (ZR80), and extends
further in dark blue when set to 440× (ZR90), 400× (ZR85) or 360× (ZR80).
❍ Keep at least 3.3 ft. (1 m) to the subject. At wide-angle, you can focus on a
subject as close as 0.39 in. (1 cm).
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Tips for Making Better Videos
Holding the Camcorder
For maximum stability, grip the camcorder in your right hand and keep
your right elbow pressed against your body. If necessary, support the
camcorder with your left hand. Be careful that your fingers do not
touch the microphone or lens.
For More Stability
Lean against a wall
Put the camcorder on a table
Lie on your elbow
Use a tripod
Lighting
When recording outdoors, we
recommend recording with the sun
at your back.
❍ When using a tripod, do not leave the viewfinder exposed to direct sunlight as
it may melt (due to concentration of the light by the lens).
❍ Do not use tripods with fastening screws longer than 0.2 inch (5.5 mm) as it
may damage the camcorder.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back a Tape
If the playback picture is distorted, clean the video heads using a Canon Head
Cleaning Cassette or a commercially available digital video head-cleaning cassette
E
(
135).
1. Set the camcorder to PLAY (VCR)
mode.
•
Set the POWER switch to
PLAY (VCR) and the TAPE/CARD switch to
b.
q
•
Set the POWER switch to PLAY
(VCR).
ER
W
PO
CAMERA
OFF
)
CR
(VCR)
A
Y
PL
2. Open the LCD panel.
r
t
You can also close the LCD panel with the
screen facing outward.
e
3. Press the ` button to rewind the
tape.
4. Press the e/a button to begin
playback.
w
5. Press the 3 button to stop playback.
❍ To use the viewfinder, close the LCD panel. The built-in speaker does not
sound. Use headphones when using the viewfinder.
❍ About the screen display: During playback, the time code gives the hours,
minutes, seconds and frames. The remaining tape time may not appear when
the time left is less than 15 seconds.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Playback Modes
` (rewind) button
1 (fast forward) button
FF
+/
REW
–/
PLAY
STOP
× 2
PAUSE SLOW
3 (stop) button
e/a (play/pause)
button
e/a (Playback Pause)
To pause playback, press the e/a button during normal playback.
1 (Fast Forward Playback) / ` (Rewind Playback)
Plays back the tape at 9.5 times normal speed (forward or reverse). Press and hold the
button during normal playback or fast forward.
–/4a (Reverse Playback)
Press the button on the wireless controller during normal playback. Press the e (play)
button to return to normal playback.
+/ae (Frame Advance) / –/4a (Frame Reverse)
Plays back frame-by-frame. Press the button on the wireless controller repeatedly
during playback pause. Press and hold it to play back continuous frame advance/frame
reverse.
SLOW M (Slow Forward)/(Slow Reverse)
Plays back at about 1/3 normal speed. Press the button on the wireless controller
during normal or reverse playback. Press the e (play) button to return to normal
playback.
× 2 (Forward ×2 Playback)/(Reverse ×2 Playback)
Plays back at 2 times normal speed. Press the button on the wireless controller during
normal or reverse playback. Press the e (play) button to return to normal playback.
❍ There is no sound during special playback.
❍ The picture may become distorted during some special playback modes.
❍ The camcorder stops the tape automatically after 5 minutes in playback pause
mode to protect tape and video heads.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Volume
When you use the LCD screen for playback, the camcorder plays back the sound via
built-in speaker. The built-in speaker does not sound when you close the LCD panel.
E
AV
H (phones) terminal
Built-in speaker
SET dial
When Using Headphones
The headphones terminal also serves as AV terminal. Headphones can only be used
when "H" is displayed on the screen. If not, change the setting following the
procedure below.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
VCR SETUP
AV/PHONES
••AV
(
39)
Open the menu and select [VCR SETUP]. Select [AV/PHONES H], set it to
[PHONES H] and close the menu.
❍ The built-in speaker does not sound when “H” is displayed.
❍ Do not connect headphones unless “H” is displayed as it produces noise.
Adjusting the Volume
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY
Turn the SET dial up to increase the volume, and down
to lower the volume.
• A volume bar appears for 2 seconds.
• You can turn off the volume completely by turning the SET dial
down until [OFF] appears. Turn the SET dial up to increase the volume again.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back on a TV Screen
The AV terminal also serves as headphones terminal. When "H" is displayed on the
screen, change the setting following the procedure below.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
VCR SETUP
AV/PHONES
••AV
(
39)
Open the menu and select [VCR SETUP]. Select [AV/PHONES H ], set it to
[AV] and close the menu.
TVs with Audio/Video Terminals
Refer also to the TV or VCR instruction manual.
VIDEO
Signal flow
AUDIO
AV
L
STV-250N Stereo Video Cable
(supplied)
R
1. Turn off all devices before starting the connections.
2. Connect the STV-250N Stereo Video Cable to the camcorder’s AV
terminal and the audio/video terminals on the TV/VCR.
Connect the white plug to the white audio terminal L (left), the red plug to the red
audio terminal R (right) and the yellow plug to the yellow video terminal VIDEO.
3. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
TVs with S (S1)-Video Input Terminal
Refer also to the TV or VCR instruction manual.
E
INPUT
Signal flow
S(S1)-VIDEO
S-150 S-video Cable (optional)
VIDEO
AUDIO
L
Signal flow
AV
R
STV-250N Stereo Video Cable
(supplied)
1. Turn off all devices before starting the connections.
2. Connect the S-150 S-video Cable (optional) to the S-video terminals.
3. Connect the STV-250N Stereo Video Cable to the camcorder’s AV
terminal and the audio terminals of the TV/VCR.
Connect the white plug to the white AUDIO terminal L (left), and the red plug to the
red AUDIO terminal R (right). Do not connect the yellow plug.
4. If connecting to a TV, set the input selector to VIDEO. If connecting to a
VCR, set the input selector to LINE.
❍ We recommend powering the camcorder from a household power source.
❍
For high picture quality, we recommend using a TV with an S (S1)
terminal.
❍ TVs with S1-terminal or Video ID-1 system: Recordings made in the 16:9 mode
78) will be automatically played back in widescreen mode.
(
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Audio Output Channel
You can select the output channels when playing back a tape with audio recorded on
two channels.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
AUDIO SETUP
OUTPUT CH••••L/R
(
39)
1. Press the MENU button to open the menu.
2. Turn the SET dial to select [AUDIO SETUP] and press
the SET dial.
3. Turn the SET dial to select [OUTPUT CH] and press
the SET dial.
4. Turn the SET dial to select a setting option.
• L/R: Stereo: L+R channels, Bilingual: Main+Sub.
• L/L: Stereo: L channel, Bilingual: Main.
• R/R:Stereo: R channel, Bilingual: Sub.
5. Press the MENU button to close the menu.
The setting resets to the L/R setting when you turn the camcorder off.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus and Settings
Many of the camcorder’s advanced functions are selected from menus that appear on
the screen.
E
Menu button
SET dial
Selecting Menus and Settings
1. Press the MENU button to open the menu.
2. Turn the SET dial to select a submenu and press the
SET dial.
3. Turn the SET dial to select a menu item and press the
SET dial.
4. Turn the SET dial to select a setting option.
5. Press the MENU button to close the menu.
When setting the white balance or shutter speed, press the SET
dial first before pressing the MENU button.
❍ Pressing the MENU button at any time closes the menu.
❍ Items that are not available appear in purple.
❍
You may find it more convenient to use the wireless controller
to operate the menu. Press the MENU button on the wireless controller to
open or close the menu. Use the select buttons in place of the SET dial and
press the SET button in place of pressing the SET dial.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu and Default Settings
Default settings are shown in boldface.
CAMERA MENU
PLAY (VCR)
CARD CAMERA
Setting Options
CARD CHROMA, CARD LUMI.,
CAM. CHROMA, C. ANIMATION
CORNER, STRAIGHT, RANDOM
CARD PLAY
CAMERA
Submenu
\CARD MIX*
Menu Item
MIX TYPE
111
ANIMAT. TYPE
MIX LEVEL
CAMERA SETUP SHUTTER
D. ZOOM
AUTO, 1/60, 1/100, 1/250, 1/500, 1/1000,
56
31
1/2000
ZR90
ZR85
OFF, 80 ,
ZR80
OFF, 72 ,
× 360×
OFF, 88 ,
× 440×
× 400×
A.SL SHUTTER
ON, OFF
ON, OFF
ON, OFF
57
79
78
54
49
50
97
59
61
60
60
61
26
IMG STAB i
16:9
WHITE BAL.
NIGHT MODE**
SKIN DETAIL
PHOTO REC*
REC MODE
AUTO, SET W, INDOOR T, OUTDOOR U
NIGHT, NIGHT+, S.NIGHT
SOFT, NORMAL
TAPE , CARD
SP, LP
VCR SETUP
AV/PHONES H
WIND SCREEN
AUDIO MODE
H VOLUME
AV, PHONES H
ON, OFF
AUDIO SETUP
16bit, 12bit
DISPLAY SETUP/ BRIGHTNESS
LCD MIRROR
TV SCREEN
D/T DISPLAY
LANGUAGE
ON, OFF
ON, OFF
ON, OFF
25
128
23
DEUTSCH, ENGLISH, ESPAÑOL, FRANÇAIS,
ITALIANO,
76
,
,
DATE FORMAT
DEMO MODE
76
79
77
78
21
21
ON, OFF
SYSTEM
WL. REMOTE*
BEEP
A1, A2, OFF B
ON, OFF
T.ZONE/DST
D/TIME SET
See list of time zones
* ZR90/ZR85 only.
** ZR90 only.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Submenu
MY CAMERA
Menu Item
S-UP IMAGE**
Setting Options
ON, OFF
75
75
S-UP SOUND
ZR90/ZR85:
OFF, DEFAULT, MY SOUND1, MY SOUND2
E
SHTR SOUND*
OPER. SOUND
SELF-T SOUND
ZR80:
OFF, PATTERN1, PATTERN2, PATTERN3
* ZR90/ZR85 only.
** ZR80 only.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAY (VCR) MENU
CAMERA
CARD CAMERA
Setting Options
CARD CAMERA
PLAY (VCR)
Submenu
VCR SETUP
Menu Item
REC MODE
SP, LP
59
35
84
38
88
60
60
89
89
93
94
95
115
26
128
128
71
70
70
76
76
77
78
21
21
AV/PHONES H
AV \DV OUT
OUTPUT CH
AV, PHONES H
ON, OFF
AUDIO SETUP
L/R, L/L, R/R
AUDIO DUB.*
WIND SCREEN*
AUDIO MODE
12bit AUDIO
MIX BALANCE
IMG QUALITY
MOVIE SIZE
AUDIO IN, MIC. IN
ON, OFF
16bit, 12bit
STEREO1, STEREO2,MIX/FIXED, MIX/VARI.
CARD SETUP*
SUPER FINE, FINE, NORMAL
320 × 240, 160 × 120
RESET, CONTINUOUS
CANCEL, EXECUTE
FILE NOS.
CARD
OPERATIONS*
COPY [
\
]
DISPLAY SETUP/ BRIGHTNESS
TV SCREEN
ON, OFF
DISPLAYS
ON, OFF <PLAYBK>
6SEC. DATE
ON, OFF
DATA CODE
DATE/TIME, CAMERA DATA, CAM. & D/T
DATE, TIME, DATE & TIME
DEUTSCH, ENGLISH, ESPAÑOL, FRANÇAIS,
D/TIME SEL.
LANGUAGE
ITALIANO,
,
,
DATE FORMAT
WL. REMOTE*
BEEP
SYSTEM
A1, A2, OFF B
ON, OFF
T.ZONE/DST
D/TIME SET
See list of time zones
* ZR90/ZR85 only.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Submenu
MY CAMERA
Menu Item
S-UP IMAGE**
Setting Options
ON, OFF
75
75
S-UP SOUND
ZR90/ZR85:
OFF, DEFAULT, MY SOUND1, MY SOUND2
E
SHTR SOUND*
OPER. SOUND
SELF-T SOUND
ZR80:
OFF, PATTERN1, PATTERN2, PATTERN3
* ZR90/ZR85 only.
** ZR80 only.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CARD CAMERA MENU
CAMERA
Submenu
PLAY (VCR)
CARD PLAY
CARD CAMERA
Menu Item
Setting Options
AUTO, 1/60, 1/100, 1/250
CAMERA SETUP SHUTTER
56
31
54
103
49
50
100
93
93
94
95
61
60
61
26
25
128
23
76
76
79
77
78
21
21
75
D.ZOOM
ZR90
OFF, 88×
ZR85
OFF, 80×
WHITE BAL.
AUTO, SET W, INDOOR T, OUTDOOR U
FOCUS PRI.
ON, OFF
NIGHT MODE
SKIN DETAIL
REVIEW
NIGHT,
NIGHT+,
S.NIGHT
SOFT, NORMAL
OFF, 2sec, 4sec, 6sec, 8sec, 10sec
SUPER FINE, FINE, NORMAL
1024 × 768, 640 × 480
320 × 240, 160 × 120
RESET, CONTINUOUS
AV, PHONES H
CARD SETUP
IMG QUALITY
IMAGE SIZE
MOVIE SIZE
FILE NOS.
VCR SETUP
AV/PHONES H
WIND SCREEN
AUDIO SETUP
ON, OFF
VOLUME
H
DISPLAY SETUP/ BRIGHTNESS
LCD MIRROR
ON, OFF
TV SCREEN
ON, OFF
D/T DISPLAY
ON, OFF
LANGUAGE
DEUTSCH, ENGLISH, ESPAÑOL, FRANÇAIS,
ITALIANO,
,
,
DATE FORMAT
DEMO MODE
ON, OFF
SYSTEM
WL. REMOTE
BEEP
A1, A2, OFF B
ON, OFF
T.ZONE/DST
D/TIME SET
S-UP SOUND
SHTR SOUND
OPER. SOUND
SELF-T SOUND
See list of time zones
MY CAMERA
OFF, DEFAULT, MY SOUND1, MY SOUND2
44
Download from Www.Somanuals.com. All Manuals Search And Download.
CARD PLAY MENU
CAMERA
Submenu
CARD
OPERATIONS
PLAY (VCR)
CARD CAMERA
CARD PLAY
E
Menu Item
Setting Options
CANCEL, EXECUTE
COPY [
\
]
116
127
(Single Image
PRINT ORDERS
ALL ERASE
NO,YES
Display)
IMAGE ERASE
FORMAT
CANCEL, SINGLE, ALL
CANCEL, EXECUTE
110
117
109
126
59
\
CARD
OPERATIONS
(Index Screen)
PROTECT
\
PRINT ORDER
VCR SETUP
REC MODE
SP, LP
AV/PHONES H
AV, PHONES H
35
DISPLAY SETUP/ BRIGHTNESS
TV SCREEN
26
ON, OFF
128
128
70
DISPLAYS
ON, OFF <PLAYBK>
DATE, TIME, DATE & TIME
D/TIME SEL.
LANGUAGE
DEUTSCH, ENGLISH, ESPAÑOL, FRANÇAIS,
76
ITALIANO,
,
,
DATE FORMAT
76
SYSTEM
WL. REMOTE
BEEP
A1, A2, OFF A
ON, OFF
77
78
T.ZONE/DST
D/TIME SET
See list of time zones
21
21
MY CAMERA
CREATE START-UP IMAGE
119
75
SEL. S-UP IMG
S-UP SOUND
SHTR SOUND
OPER. SOUND
SELF-T SOUND
NO IMAGE, CANON LOGO, MY IMAGE1,
MY IMAGE2
OFF, DEFAULT, MY SOUND1, MY SOUND2
75
\
PRINT
Appears when connecting a printer with direct print function.
127
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Recording Programs
Easy Recording Program
The camcorder adjusts focus, exposure and other settings
[
automatically, allowing you to just point and shoot.
Program AE Modes
Auto
The camcorder adjusts focus, exposure and other settings
automatically. However, you have the option of adjusting the
settings manually.
Sports
Use this mode to record sports scenes (such as tennis or golf) or
moving objects (such as roller coasters).
Portrait
Use this mode to give accent to your subject by blurring the
background or foreground. The blur effect increases the more you
zoom to telephoto.
Spotlight
Use this mode to record spotlit scenes or fireworks.
Sand & Snow
Use this mode in bright places such as a sunny beach or ski resort. It
prevents the subject from being underexposed.
Low Light
Use this mode to record in dimly lit places.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
E
Program selector
Availability of Functions in Each Mode:
Recording Program
[
h
h
h
Digital Zoom
Image Stabilizer
Focus
h
ON
A
A
A
×
White Balance
Shutter Speed
AE Shift
h
A
h
h
×
h
Digital Effects
16:9
×
h
h
h
×
Card Mix*
×
A: Auto setting h: Available ×: Not available
Shaded area: Can be used only in CAMERA mode.
* ZR90/ZR85 only.
Selecting the Easy Recording Program
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
Set the program selector to [.
[ appears.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Program AE Mode
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
1. Set the program selector to Q.
2. Press the SET dial.
A list of the program AE modes appears.
3. Select a mode and press the SET dial.
The symbol of the mode appears on the upper left corner of the
screen.
❍ The setting resets to the Auto mode when you change the position of the
program selector.
❍ Do not change the mode during recording as the brightness of the image may
change abruptly.
❍ Sports/Portrait mode:
The picture may not appear smooth when played back.
❍ Sand & Snow mode:
-
The subject may become overexposed in dark surroundings. Check the
image on the screen.
-
The picture may not appear smooth when played back.
❍ Low Light mode:
-
-
-
Moving subjects may leave a trailing afterimage.
Picture quality may not be as good as in other modes.
The camcorder may have difficulty to focus automatically.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Night Modes
NIGHT
Allows you to record in dark places where lights cannot be
used, without sacrificing color.
E
NIGHT+
The assist lamp (white LED) lights up and stays on.
SUPER NIGHT Allows you to record in very dark places. The assist lamp
(white LED) lights up automatically responding to the
surrounding brightness.
NIGHT MODE button
Program selector
MENU button
SET dial
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
CAMERA SETUP
NIGHT MODE•••
NIGHT+
(
39)
1. Set the program selector to Q.
2. Open the menu and select [CAMERA SETUP]. Select [NIGHT MODE],
select a setting option and close the menu.
3. Press the NIGHT MODE button.
• The symbol of the selected mode appears on the screen.
• Pressing the NIGHT MODE button again resets the camcorder to the Auto mode.
1. Set the program selector to Q.
2. Press the NIGHT MODE button.
• "
" appears.
• Pressing the NIGHT MODE button again resets the camcorder to the Auto mode.
❍ Moving subjects may leave a trailing afterimage.
❍ Picture quality may not be as good as in other modes.
❍ White points may appear on the screen.
❍ Autofocus may not work as well as in other modes. In such case, adjust the
focus manually.
❍ Digital zoom and multi-image screen cannot be used while a Night mode is
activated.
❍ The program AE mode cannot be changed while a Night mode is activated.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Skin Detail Function
The camcorder detects skin tones and adjusts the picture for a more smooth and
natural appearance of the skin area.
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
CAMERA SETUP
SKIN DETAIL••NORMAL
(
39)
Open the menu and select [CAMERA SETUP]. Select [SKIN DETAIL], set it to
[SOFT] and close the menu.
❍ Skin detail function cannot be used when the program selector is set to [.
❍ To obtain the best effect, use this function when recording a person in
close-up. Note that areas similar to the skin color may lack in detail.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the AE Shift
You can adjust the AE (auto exposure) function to lighten or darken the image. This
allows you to compensate for backlit or overexposed scenes. Available Levels: –2 to +2,
in 0.25 intervals (excluding –1.75 and +1.75).
E
AE SHIFT button
SET dial
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
1. Set the program selector to Q.
2. Set the program AE mode to
Light mode.
Auto,
Sports,
Portrait or
Low
3. Press the AE SHIFT button.
“AE 0” appears in light blue.
AE SHIFT/
END SEARCH
4. Turn the SET dial to adjust the AE shift level.
• Turn the SET dial up to lighten the image and down to darken
the image.
• If “MF” is displayed in light blue, AE shift cannot be adjusted.
Press the AE SHIFT button again to display “AE 0” in light blue.
The camcorder retains the setting even if you turn it off or change the program
AE mode.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Focus Manually
Autofocus may not work well on the following subjects. In such case, focus manually.
Subjects with
Through dirty or
wet windows
Reflective surfaces
low contrast or
Fast Moving Subjects
without vertical lines
Zoom lever
FOCUS button
Program selector
SET dial
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
1. Set the program selector to Q.
2. Adjust the zoom.
When you operate the zoom after adjusting the focus, the
subject may not stay in focus. Adjust the zoom before the focus.
3. Press the FOCUS button.
“MF” appears.
4. Turn the SET dial to adjust the focus.
• Turn the SET dial up or down until the image appears focused.
• Press the FOCUS button to return to autofocus.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ The setting resets to autofocus when you switch the program selector to [.
❍ Readjust the focus when you have turned off the camcorder.
E
Infinity Focus
Use this function when you wish to focus on faraway subjects such as mountains or
fireworks.
Press the FOCUS button more than 2 seconds after step 2 in Adjusting the
Focus Manually.
"MF ∞" appears.
When you operate the zoom or turn the SET dial, "∞" disappears and the
camcorder changes to manual focus.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the White Balance
You can use the preset modes to reproduce colors more accurately, or set a custom
white balance to obtain the optimal setting.
AUTO
Auto white balance
SET W
INDOOR T
Custom white balance setting
Use this mode for recording under changing lighting condition, video
lights or sodium lamps.
OUTDOOR U Use this mode for recording night scenes, fireworks, sunrise or sunset.
Zoom lever
White sheet or paper
MENU button
Program selector
SET dial
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
CAMERA SETUP
WHITE BAL.•••AUTO
(
39)
1. Set the program selector to Q.
2. For custom white balance: Point the camcorder at a white object and
zoom in until it fills the whole screen.
Keep the camcorder zoomed at the white object until step 4 is completed.
3. Open the menu and select [CAMERA SETUP]. Select [WHITE BAL.], select
a setting option and close the menu.
When you have selected [SET W]: “W” flashes and stops flashing when settings is
complete.
4. Close the menu.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ Use the auto setting for normal outdoor scenes.
❍ When the program selector is set to [, white balance is preset to [AUTO].
❍ The camcorder retains the custom white balance setting even if you turn it off.
ZR90/ZR85: However, it resets to [AUTO] when you change the position of the
TAPE/CARD switch.
E
❍ When you have set the custom white balance:
-
Depending on the light source, “W” may keep flashing. The result will still
be better than with the auto setting.
-
-
Reset the white balance when the lighting condition changes.
Turn off the digital zoom.
❍ Custom white balance may provide better results in the following cases:
-
-
-
-
Changing lighting conditions
Close-ups
Subjects in a single color (sky, sea or forest)
Under mercury lamps or certain types of fluorescent lights
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Shutter Speed
You can adjust the shutter speed manually to make stable shots of fast moving
subjects.
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
CAMERA SETUP
SHUTTER••••••AUTO
(
39)
1. Set the program selector to Q.
2. Set the program AE mode to the
(Auto) mode.
3. Open the menu and select [CAMERA SETUP].
4. Select [SHUTTER].
5. Select the shutter speed and press the SET dial.
CAMERA Mode
CARD CAMERA Mode
AUTO
1/60
AUTO
1/60
1/100
1/250
1/500
1/1000
1/2000
1/100
1/250
6. Close the menu.
❍
If the shutter speed is set to 1/500 or higher in CAMERA mode
and you switch to CARD CAMERA mode, it automatically changes to 1/250.
❍ Do not point the camcorder directly at the sun when the shutter speed is set to
1/1000 or higher.
❍ The image may flicker when recording with high shutter speeds.
❍ Recording under fluorescent lights (CAMERA mode): In Easy Recording, Auto
mode or the Night modes, the camcorder automatically detects the flicker of
fluorescent lighting and adjusts the shutter speed accordingly. However, if the
screen starts to flicker, select AUTO mode and set the shutter speed to 1/100.
❍ The setting resets to the auto setting when you switch the program selector to
[, or change the program AE mode.
❍ Guidelines for Recording with High Shutter Speeds:
-
-
-
Outdoor sports such as golf or tennis: 1/2000
Moving objects such as cars or roller coasters: 1/1000, 1/500 or 1/250
Indoor sports such as basketball: 1/100
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto Slow Shutter
In Easy Recording mode and when [SHUTTER] is set to [AUTO] in Auto mode, the
camcorder uses shutter speeds down to 1/30. This allows you to record brightly in
places with insufficient lighting. However, you can set the camcorder not to use the
slow shutter speed of 1/30.
E
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
CAMERA SETUP
A.SL SHUTTER•ON
(
39)
Open the menu and select [CAMERA SETUP]. Select [A.SL SHUTTER], set it
to [OFF] and close the menu.
When set to [ON], moving subjects may leave a trailing afterimage.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Self-Timer
The self-timer can be used for recording movies and still images.
PHOTO button
(self-timer) button
Start/stop button
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
When recording movies
1. Press the (self-timer) button.
“
” appears.
DATA CODE
2. Press the start/stop button.
ER
W
POWER
• The camcorder starts recording after a 10-second countdown
(ZR90/ZR85: 2 seconds when using the wireless controller). The
count down appears on the screen.
A
R
E
M
A
C
F
F
O
)
TR
(V
Y
LA
P
• To record a still image, press the PHOTO button (
29).
❍ To cancel the self-timer, press the (self-timer) button. Once the countdown
has begun, you can also press the start/stop button (when recording movies) or
the PHOTO button (when recording still image) to cancel the self-timer.
❍ The self-timer will be canceled when you turn off the camcorder.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Recording Mode (SP/LP)
You can choose between SP (standard play) and LP (long play). LP extends the tape
usage by 1.5 times.
E
CARD CAMERA
CAMERA
PLAY (VCR)
CARD PLAY
VCR SETUP
REC MODE•••••SP
(
39)
To change to LP mode, open the menu and select [VCR SETUP]. Select [REC
MODE], set it to [LP] and close the menu.
❍
Tapes recorded in LP mode cannot be used for audio
88) or AV insert ( 86).
dubbing (
❍ Depending on the nature and usage condition of the tape, picture and
sound recorded in LP mode may be distorted. We recommend using the
SP mode for important recordings.
❍ If you record in both SP and LP modes on the same tape, the playback picture
may become distorted and the time code may not be written correctly.
❍ If you play back a tape that has been recorded in LP mode with another digital
device on this camcorder, or vice versa, picture and sound may become
distorted.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Recording
Changing the Audio Mode
You can record sound in two audio modes—16-bit and 12-bit. The 12-bit mode records
sound on two channels (stereo 1), leaving 2 channels free (stereo 2) for adding new
sound later. Select the 16-bit mode for higher sound quality.
CARD CAMERA
CARD PLAY
CAMERA
PLAY (VCR)
AUDIO SETUP
AUDIO MODE•••12bit
(
39)
Open the menu and select [AUDIO SETUP]. Select [AUDIO MODE], set it to
[16bit] and close the menu.
“16bit” appears for approximately 4 seconds.
Wind Screen
You can reduce the wind noise when recording in windy places.
CARD PLAY
CAMERA
PLAY (VCR)
*
CARD CAMERA
* ZR90/ZR85 only.
AUDIO SETUP
WIND SCREEN••OFF
(
39)
Open the menu and select [AUDIO SETUP]. Select [WIND SCREEN], set it to
[ON] and close the menu.
“WS O” appears when you turn the wind screen on.
❍ Low sound may be reduced together with the wind noise. We recommend
turning off the wind screen for normal recordings.
❍
The wind screen function can also be used for audio dubbing
(when [AUDIO DUB.] is set to [MIC. IN] in the [AUDIO SETUP] submenu).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Headphones during Recording
The headphones terminal also serves as AV terminal. Headphones can only be used
when "H" is displayed on the screen. If not, change the setting following the
procedure below.
E
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
VCR SETUP
AV/PHONES
••AV
(
39)
Open the menu and select [VCR SETUP]. Select [AV/PHONES H ], set it to
[PHONES H ] and close the menu.
Adjusting the Headphone Volume
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
AUDIO SETUP
HVOLUME•••••
(
39)
Open the menu and select [AUDIO SETUP]. Select [ H VOLUME], adjust the
volume with the SET dial and close the menu.
You can turn off the volume completely by turning the SET dial down until [OFF] appears.
Turn the SET dial up to increase the volume again.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Digital Effects
Faders (
65)
Begin or end scenes with a fade to or from black.
The image gradually fades in.
Fade Trigger (FADE-T)
The image gradually fades out.
The image begins as a vertical line in the
center and expands sideways until it fills
the whole screen.
Wipe (WIPE)
The image is wiped off from the sides of
the screen.
The image appears from the corners until
it fills the whole screen.
Corner Wipe (CORNER)
Jump (JUMP)
The image is wiped off from the corners.
A small image appears from the left,
jumps into the center and enlarges until
it fills the whole screen.
The image shrinks, jumps from the center
to the left and disappears.
The image flips into the screen.
The image flips out of the screen.
Flip (FLIP)
62
Download from Www.Somanuals.com. All Manuals Search And Download.
The image appears in 16 pieces. The
pieces move around until the puzzle is
solved.
Puzzle (PUZZLE)
Zigzag (ZIGZAG)
Beam (BEAM)
Tide (TIDE)
E
The image is divided into 16 pieces. The
pieces move around and disappear.
The image appears in zigzag from the
top of the screen.
Black stripes appear in zigzag from the
bottom of the screen until they cover the
whole image.
The screen turns yellow, forms a beam
that becomes thinner and the image
appears.
A yellow beam appears in the center of
the screen and expands until it covers the
whole image.
The image appears from both sides like
tides.
The image disappears from both sides
like tides.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Effects (
66)
Add flavor to your recordings.
Art (ART)
The image becomes like a
paint (solarization).
Black and White (BLK Sepia (SEPIA)
The image becomes
monochrome with a
brownish tint.
& WHT)
The image becomes black
and white.
Mosaic (MOSAIC)
The image is blurred
Ball (BALL)
Cube (CUBE)
The image becomes like a The image becomes a
through enlarging the size ball.
of some pixels.
cube and rotates.
Wave (WAVE)
Both ends of the image
sway in waves.
Color Masking (COLOR M.) Mirror (MIRROR)
The image becomes a Creates a symmetrical
rhombus surrounded by a image as if there would
masking frame that
changes the colors.
be a mirror in the center
of the screen.
Multi-Image Screen (
67)
Captures moving subjects in 4, 9 or 16 sequences of still images and displays them at
one time. Sound will be recorded normally.
4 Sequences
9 Sequences
16 Sequences
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Availability of Digital Effects by Operating Modes:
CAMERA
PLAY (VCR)
Movies Still Images
CARD CAMERA
CARD PLAY
E
Faders
Effects
h
h
i
h
h
h
i
i
i
h*
Multi-image
screen
h
h
h
i
i
h: Available i: Not available
* : Black and White only.
Selecting a Fader
In CAMERA mode, set the program selector to Q.
CARD CAMERA
CARD PLAY
CAMERA
PLAY (VCR)
1. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
2. Select [FADER].
3. Select the fader option.
4. Press the DIGITAL EFFECTS button.
The name of the selected fader flashes.
CAMERA mode:
5. Fade in: In record pause mode, press the ON/OFF
button and begin recording by pressing the
start/stop button.
ON/OFF
Fade out: During recording, press the ON/OFF button
and pause recording by pressing the start/stop
button.
The fader can be activated/deactivated by pressing the ON/OFF button.
PLAY (VCR) mode:
5. Fade in: In playback pause mode, press the ON/OFF
button and begin playback by pressing the e/a
button.
ON/OFF
Fade out: During playback, press the ON/OFF button
and pause playback by pressing the e/a button.
The fader can be activated/deactivated by pressing the ON/OFF button.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting an Effect
In CAMERA mode, set the program selector to Q.
CARD CAMERA
CARD PLAY
CAMERA
PLAY (VCR)
1. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
2. Select [EFFECT].
3. Select the effect.
4. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
The name of the selected effect flashes.
5. Press the ON/OFF button.
ON/OFF
• The name of the selected effect stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
Selecting an Effect in CARD CAMERA Mode
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
1. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
“BLK&WHT” flashes.
2. Press the ON/OFF button.
ON/OFF
• “BLK&WHT” stops flashing.
• The effect can be activated/deactivated by pressing the ON/OFF
button.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Multi-Image Screen
You can operate the multi-image screen only in the following playback modes:
- When [S.SPEED] is set to [MANUAL]: Playback pause, slow forward/reverse playback
- When [S.SPEED] is set to [FAST], [MOD.] or [SLOW]: Playback pause
In CAMERA mode, set the program selector to Q.
E
CARD CAMERA
CARD PLAY
CAMERA
PLAY (VCR)
1. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
[D.EFFECTS |], [FADER], [EFFECT] and [MULTI-S] appear.
2. Select [MULTI-S].
[S.SPEED] and [S.SPLIT] appears.
3. Select [S.SPEED].
[MANUAL], [FAST], [MOD.] and [SLOW] appear.
4. Select the transition speed.
Following transition speeds can be selected: fast (every 4 frames), moderate (every 6
frames*), slow (every 8 frames*).
* In Low Light mode: moderate (every 8 frames), slow (every 12 frames).
5. Select [MULTI-S] again.
[S.SPEED] and [S.SPLIT] appears.
6. Select [S.SPLIT].
[4], [9], [16] settings appear.
7. Select the number of sequences.
8. Press the DIGITAL EFFECTS button.
DIGITAL
EFFECTS
“MULTI-S” flashes.
9. Press the ON/OFF button.
ON/OFF
• MANUAL: Images will be captured each time you press the
ON/OFF button. The blue frame indicating the next sequence
disappears after the last image. To cancel the last captured
image, press and hold the ON/OFF button. To cancel the
multi-image screen, press and release the ON/OFF button.
• FAST, MODERATE, SLOW: The set number of images will be captured at the set
speed. To cancel the multi-image screen, press the ON/OFF button.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Press the start/stop button to begin recording.
The multi-image screen is recorded on the tape.
❍ Turn off the digital effect when you do not use it.
Press the DIGITAL EFFECTS button to open the menu. Select [D.EFFECTS |]
and press the DIGITAL EFFECTS button.
❍ The camcorder retains the setting even if you turn it off or change the program
AE mode.
❍ Digital effects cannot be used when the program selector is set to [.
❍ Digital effects cannot be used during DV dubbing and photo/date search.
❍ The digital effects can be operated in record or record pause mode.
❍ The multi-image screen cannot be used in the Night modes.
❍ The multi-image screen cannot be used when the 16:9 format is selected.
❍
Faders and multi-image screen cannot be selected when Card
Mix is activated.
❍ In PLAY (VCR) mode: Pressing any tape operation button (such as play or
pause), or performing date/photo search cancels the multi-image screen.
❍ The image quality may be slightly lower with digital effects.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnifying the Image
The playback image can be magnified up to 5 times.
E
Zoom lever
SET dial
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY
1. Move the zoom lever toward T.
• The image is magnified by 2 times.
• A frame appears indicating the position of the magnified area.
• To further enlarge the image, move the zoom lever toward T.
To shrink the image below 2 times magnification, move the
zoom lever toward W.
2. Selected the magnified area with the SET dial.
• Turn the SET dial to move the image to the right and left, or up
and down. Pressing the SET dial switches between the
directions.
• To cancel the magnification, move the zoom lever toward W
until the frame disappears.
Movies played back from a memory card cannot be magnified.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Data Code
The camcorder maintains a data code containing recording date and time and other
camera data such as shutter speed and exposure (f-stop). When you play back a tape,
you can display the data code and select the data code combination you wish to
display.
DATA CODE button
MENU button
SET dial
Selecting the Date/Time Display Combination
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY
D/TIME SEL.••DATE & TIME
DISPLAY SETUP/
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [D/TIME SEL.], set it
to [DATE] or [TIME] and close the menu.
Selecting the Data Code Display Combination
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
DATA CODE••••DATE/TIME
DISPLAY SETUP/
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [DATA CODE], set it
to [CAMERA DATA] or [CAM. & D/T] and close the menu.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Data Code
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY
E
Press the DATA CODE button.
❍ The data code display turns off when you turn the camcorder off.
Only date and time appear in CARD PLAY mode.
❍
Six-Second Auto Date
Date and time appear for 6 seconds when you begin playback, or to indicate that date
or time zone has changed.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
DISPLAY SETUP/
6SEC.DATE••••OFF
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [6SEC.DATE], set it
to [ON] and close the menu.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
End Search
When you have played back a tape, you can use this function to locate the end of the
last recorded scene.
END SEARCH button
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
In stop mode, press the END SEARCH button.
• "END SEARCH" appears.
• The camcorder rewinds/fast forwards the tape, plays back the last few seconds of the
recording and stops the tape.
• Pressing the button again cancels the search.
❍ End search cannot be used once you unload the cassette.
❍ End search may not work properly if a blank section exists on the tape.
❍
You cannot use end search to locate the editing end of AV
insert or audio dubbing.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Returning to a Pre-marked Position
If you wish to return to a particular scene
E
later, mark the point with the zero set
memory and the tape will stop at that point
when you rewind/fast forward the tape.
This function is operated with the wireless
controller.
REW ` button
PLAY e button
ZERO SET
MEMORY
button
STOP 3 button
CARD CAMERA
CARD PLAY
CAMERA
PLAY (VCR)
DATA CODE
SLIDE SHOW
SEARCH SELECT
REW
CARD
1. Press the ZERO SET MEMORY button at the point
you wish to return to later.
ZERO SET
MEMORY
PLAY
STOP
FF
• “0:00:00 ” appears.
12bit
AUDIO OUT
• To cancel, press the ZERO SET MEMORY button again.
2. When you have finished playback, rewind the tape.
• “` RTN” appears.
• The tape stops automatically at “0:00:00”.
• The tape counter changes to time code.
The zero set memory may not function correctly when the time code has not
been recorded consecutively.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Photo Search/Date Search
You can search for a still image recorded
SEARCH SELECT button
anywhere on the tape with the photo search
function, or locate the change of the
date/time zone with the date search function.
This function is operated with the wireless
controller.
+/- (search) buttons
STOP 3 button
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Press the SEARCH SELECT button to choose between
photo search and date search.
DATA CODE
SLIDE SHOW
SEARCH SELECT
REW
CARD
ZERO SET
MEMORY
PLAY
STOP
FF
“PHOTO SEARCH” or “DATE SEARCH” appears.
12bit
AUDIO OUT
2. Press the + or - button to begin searching.
DATA CODE
SLIDE SHOW
SEARCH SELECT
CARD
• Press more than once to search for further still images or date
changes (up to 10 times).
ZERO SET
MEMORY
REW
PLAY
STOP
FF
12bit
AUDIO OUT
• Press the STOP 3 button to stop searching.
❍ Photo search: A still image recorded very close to the point you start the search
may not be detected.
❍ Date search: A recording of longer than a minute per date/area is required.
❍ Date search may not function if the data code is not correctly displayed.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Customizing the Camcorder
You can personalize your camcorder by customizing the start-up image and the sound
E
it makes for start-up, shutter*, operation and self-timer (collectively called the My
Camera settings).
* ZR90/ZR85 only.
Changing the My Camera Settings
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
MY CAMERA
(
39)
SEL.S–UP IMG•CANON LOGO
S–UP SOUND•••DEFAULT
SHTR SOUND•••DEFAULT
OPER.SOUND•••DEFAULT
SELF–T SOUND•DEFAULT
S–UP IMAGE•••ON
S–UP SOUND•••PATTERN1
OPER.SOUND•••PATTERN1
SELF–T SOUND•PATTERN1
1. Open the menu and select [MY CAMERA].
2. Select the menu item you wish to change.
When selecting a start-up image, set the camcorder to CARD PLAY
mode.
3. Select a setting option and close the menu.
❍ You can save your original images, or the images and sounds contained in the
supplied software (ZoomBrowser EX for Windows or ImageBrowser for
Macintosh) to the setting options [MY IMAGE1], [MY IMAGE2], [MY SOUND1]
and [MY SOUND2]. For details, refer to the Digital Video Software Instruction
Manual.
❍ You can also create original start-up images (
119).
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Display Language
The language used in the camcorder displays and menu items can be changed to
German, Spanish, French, Italian, Russian, Simplified Chinese or Japanese.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
DISPLAY SETUP/
LANGUAGE •••ENGLISH
(
39)
To change the display language, open the menu and select [DISPLAY
SETUP/ ]. Select [LANGUAGE ], select a language and close the menu.
If you have mistakenly changed the language, follow the
menu item to change the setting.
mark next to the
Changing the Date Format
You can select between three date formats. For example, [JAN. 1, 2004], [1. JAN. 2004]
and [2004. 1. 1].
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
DISPLAY SETUP/
DATE FORMAT••JAN. 1,2004
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [DATE FORMAT],
select a format and close the menu.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Remote Sensor Mode
Two remote sensor modes and an off setting are available to prevent interference
from other Canon wireless controllers being used nearby.
E
Turning the Remote Sensor Off
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
SYSTEM
WL.REMOTE•••
•
1
(
39)
Open the menu and select [SYSTEM]. Select [WL.
REMOTE], set it to [OFF B] and close the menu.
“B“ appears.
Changing the Remote Sensor Mode
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
SYSTEM
WL.REMOTE••••
1
(
39)
1. On the camcorder, open the menu and select
[SYSTEM]. Select [WL. REMOTE], set it to [A 2] and
close the menu.
The selected mode appears for a few seconds.
2. On the wireless controller, press and hold the
REMOTE SET button. Press the ZOOM T button for
mode 2. Keep the button pressed for over 2 seconds.
AUDIO DUB. PAUSE
SLOW
2
AV INSERT AV DV REMOTE SET
REC
PAUSE
-
WIRELESS CONTROLLER WL D82
If you have set the camcorder to mode 1, press the ZOOM W
button for mode 1.
START
/STOP
ZOOM
W
T
PHOTO
SELF T. D.EFFECTS
MENU
SET
ON/OFF
TV SCREEN
❍ The wireless controller returns to mode 1 when you replace the batteries.
Change the mode if necessary.
❍ Make sure that camcorder and wireless controller are set to the same mode.
Display the camcorder’s mode by pressing any button on the wireless controller
(except of the REMOTE SET button) and set the wireless controller’s mode to
the same mode. Change the batteries if the wireless controller still does not
work.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Camcorder Settings
Beep
You will hear a beep upon camcorder operations such as power on/off, start/stop, self-
timer countdown, and unusual conditions of the camcorder.
If you turn off the beep, all camcorder sounds including the ones of the My Camera
settings will be turned off.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
SYSTEM
BEEP•••••••••ON
(
39)
To turn the beep off, open the menu and select [SYSTEM]. Select [BEEP],
set it to [OFF] and close the menu.
Recording in 16:9 (Widescreen TV Recording)
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
CAMERA SETUP
16:9•••••••••OFF
(
39)
To switch 16:9 on, open the menu and select [CAMERA SETUP]. Select
[16:9], set it to [ON] and close the menu.
”16:9” appears.
❍ The 16:9 mode is an electronically processed effect.
❍ The 16:9 mode cannot be selected in the Easy Recording mode.
❍ The multi-image screen cannot be used when the 16:9 format is selected.
❍
Simultaneous recording on a memory card cannot be used
when the 16:9 format is selected.
❍ If you play back a 16:9 recording on a normal TV, the image appears vertically
“squashed” (compressed).
❍ If you connect the camcorder to a TV with an S1 terminal or Video ID-1
system, recordings made in the 16:9 mode will be automatically played back in
widescreen mode.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning Off the Image Stabilizer
The image stabilizer compensates for camcorder shake even at full telephoto. The
image stabilizer tries to compensate horizontal movements, therefore, we recommend
turning off the image stabilizer when you mount the camcorder on a tripod.
E
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
CAMERA SETUP
IMG STAB
•••ON
(
39)
Open the menu and select [CAMERA SETUP]. Select [IMG STAB i], set it
to [OFF] and close the menu.
i disappears.
❍ The image stabilizer cannot be turned off when the program selector is set to
[.
❍ The image stabilizer is designed to compensate a normal degree of camcorder
shake.
❍ The image stabilizer might not be as effective when using the Night modes.
Demonstration Mode
The demonstration mode displays the camcorder’s main features. It starts
automatically when you leave the camcorder turned on without loading a recording
media for more than 5 minutes. However, you can set the camcorder not to start the
demonstration mode.
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
DEMO MODE••••ON
DISPLAY SETUP/
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [DEMO MODE], set
it to [OFF] and close the menu.
To cancel the demo mode once it has begun, press any button, turn off the
camcorder or load a recording media.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording to a VCR or Digital Video Device
You can copy your recordings by connecting the camcorder to a VCR or a digital video
device. If you connect a digital video device, you can copy recordings with virtually no
generation loss in image and sound quality.
Connecting the Devices
q Connecting a VCR
See Playing Back on a TV Screen (
36).
w Connecting a Digital Video Device
Refer also to the instruction manual of the digital video device.
DV
Signal flow
Commercially available DV cable
Recording
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
If you are connecting via AV terminal, check the setting ( 36).
2. Connected device: Load a blank cassette and set the device to record
pause mode.
3. Locate the scene you wish to copy and pause playback shortly before
the scene.
4. Play back the tape.
5. Connected device: Begin recording when the scene you wish to copy
appears. Stop recording when copying is complete.
6. Stop playback.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ When connecting a VCR, the quality of the edited tape will be slightly lower
than that of the original.
❍ When connecting a digital video device:
-
-
If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
Proper operation cannot be guaranteed for all digital video devices equipped
with a DV terminal. If operation does not work, use the S-video or AV
terminal.
E
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from Analog Video
Devices (VCR, TV or Camcorder)
You can record videos or TV programs from a VCR or analog camcorder on the tape in
the camcorder.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Connect the camcorder to the analog video device.
See Playing Back on a TV Screen ( 36).
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button.
In record pause mode and during recording, you can check the
picture on the screen.
CARD MIX /
/
SLIDE SHOW/
5. Connected device: Play back the tape.
REC PAUSE
6. Press the e/a button when the scene you wish to
record appears.
7. Press the 3 button to stop recording.
• Press the e/a button to pause recording.
• Press the e/a button again to restart recording.
8. Connected device: Stop playback.
Headphones cannot be used during analog line-in recording.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from Digital Video
Devices (DV Dubbing)
E
You can record from other digital video devices equipped with a DV terminal with
virtually no loss in picture and sound quality.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Connect the camcorder to the digital video device.
See Connecting a Digital Video Device ( 80).
2. Set the camcorder to PLAY (VCR) mode and load a blank cassette.
Make sure that [AV\DV OUT] is set to [OFF] ( 85).
3. Connected device: Load the recorded cassette.
4. Press the REC PAUSE button.
In record pause mode and during recording, you can check the
picture on the screen.
CARD MIX /
SLIDE SHOW/
REC PAUSE
/
5. Connected Device: Play back the tape.
6. Press the e/a button when the scene you wish to
record appears.
7. Press the 3 button to stop recording.
• Press the e/a button to pause recording.
• Press the e/a button again to restart recording.
8. Connected Device: Stop playback.
❍ Blank sections may be recorded as anomalous picture.
❍ If the picture does not appear, reconnect the DV cable or turn the camcorder
off and back on again.
❍ You can only record signals from devices with the
logo recording in SD
system in SP or LP format.
Copyright Signal
Certain software tapes are copyright protected. If you attempt to play back such tape,
“COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED” appears and you will not be able
to view the contents of the tape. If you attempt to record from such tape via the DV
terminal, “COPYRIGHT PROTECTED DUBBING RESTRICTED” appears and you will not
be able to record the contents of the tape.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Converting Analog Signals into Digital
Signals (Analog-Digital Converter)
By connecting the camcorder to a VCR or 8mm video camcorder, you can convert
analog video/audio signals to digital signals and output the digital signals via the DV
terminal. The DV terminal serves as output terminal only.
Connecting the Devices
Turn off all devices before starting the connections. Unload the tape from the
camcorder. Refer also to the instruction manual of the connected device.
You can also connect a VCR with S (S1)-VIDEO terminal (
37).
VIDEO
L
Signal flow
AV
AUDIO
R
STV-250N Stereo Video
Cable (supplied)
DV
Signal flow
Commercially available DV cable
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning On the Analog-Digital Converter
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
E
VCR SETUP
AV DV OUT••••OFF
(
39)
Open the menu and select [VCR SETUP]. Select [AV\DV OUT], set it to
[ON] and close the menu.
❍ Headphones cannot be used during analog-digital conversion.
❍ Depending on the signal sent from the connected device, the conversion from
analog to digital signals might not work properly (e.g., signals that include
copyright protective signals or anomalous signals such as ghost signals).
❍ For normal use, set [AV\DV OUT] to [OFF]. If it is set to [ON], digital signals
cannot be input via the camcorder’s DV terminal.
❍ Depending on the software and the specifications of your computer, you may
not be able to transfer converted signals via the DV terminal.
❍ We recommend powering the camcorder from a household power source.
❍
You can also press the AV\DV button on the wireless
controller. The setting changes with each press of the button.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Existing Scenes (AV Insert)
You can insert and replace images and audio on the tape of the camcorder with
images and audio from other video devices connected via AV terminal or DV terminal.
This function is operated with the wireless controller.
Scene to be inserted
Playback tape
Insert start
Insert end
Tape in the
camcorder
before inserting
Tape in the
camcorder after
inserting
Inserted scene
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Connect the camcorder to a video device.
See Playing Back on a TV Screen ( 36).
2. Connected device: Load a recorded cassette. Locate the scene you wish
to insert and pause playback shortly before the scene.
3. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
Use a tape recorded in SP mode and make sure that the tape-protect switch is set to
allow recording.
4. Locate the scene you wish to replace and pause playback shortly before
the scene.
12bit
5. Press the AV INSERT button on the wireless
STOP
AUDIO OUT
AUDIO DUB. PAUSE
SLOW
2
controller.
AV INSERT AV DV REMOTE SET
“AV INSERT” and “2a” appear.
REC
PAUSE
86
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Connected device: Play back the tape.
ZERO SET
MEMORY
7. Press the PAUSE a button on the wireless controller
when the scene you wish to insert appears.
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
E
AV INSERT AV DV REMOTE SET
ZERO SET
MEMORY
8. Press the STOP 3 button on the wireless controller
to stop inserting.
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
Press the PAUSE a button on the wireless controller to pause
inserting.
AV INSERT AV DV REMOTE SET
9. Connected device: Stop playback.
❍ You cannot insert from a TV program when the synchronized signals are
distorted.
Connected device:
❍ AV insert may not work correctly if the tape has a blank section or changes in
the recording mode.
❍ AV insert cannot be performed when the quality of the recording is poor, or
during special playback such as fast forward, rewind, playback pause, slow
playback etc.
Set the zero set memory at the end of the scene you wish to replace. The
camcorder will automatically stop AV insert at that point.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Dubbing
You can add sound from audio devices (AUDIO IN) or with the built-in microphone
(MIC. IN).
This function is operated with the wireless controller.
Connecting an Audio Device
Refer also to the instruction manual of the connected device.
Audio device
(e.g. CD player)
OUTPUT
Signal flow
AUDIO
AV
L
STV-250N Stereo Video Cable
(supplied)
R
Dubbing
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
AUDIO SETUP
AUDIO DUB.•••AUDIO IN
(
39)
1. Set the camcorder to PLAY (VCR) mode and load a recorded cassette.
Use a tape recorded in SP, 12-bit mode with this camcorder.
2. Open the menu and select [AUDIO SETUP]. Select [AUDIO DUB.], set it
to [AUDIO IN] or [MIC. IN] and close the menu.
3. Locate the scene you wish to start audio dubbing.
4. Press the PAUSE a button on the wireless controller.
5. Press the AUDIO DUB. button on the wireless
controller.
ZERO SET
REW
PLAY
STOP
SLOW
FF
MEMORY
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
“AUDIO DUB.” and “ a” appear.
AV INSERT AV DV REMOTE SET
6. Press the PAUSE a button on the wireless controller
to begin dubbing.
ZERO SET
MEMORY
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
• Audio device: Begin playback.
AV INSERT AV DV REMOTE SET
• Microphone: Speak into the built-in microphone.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
ZERO SET
MEMORY
7. Press the STOP 3 button on the wireless controller
to stop dubbing.
REW
PLAY
STOP
SLOW
FF
12bit
AUDIO OUT
AUDIO DUB. PAUSE
2
Audio device: Stop playback.
AV INSERT AV DV REMOTE SET
E
❍ Use only tapes recorded in SP mode 12-bit audio sound with this camcorder.
Audio dubbing will stop if the tape has a blank section or a section recorded in
LP mode or 16-bit mode.
❍ You cannot use the DV terminal for audio dubbing.
❍ If you add sound to a tape not recorded with this camcorder, sound quality
may decrease.
❍ Sound quality may decrease when you add sound to the same scene for more
than 3 times.
❍ When you connect an audio device, check the picture on the LCD screen and
the sound via built-in speaker or audio device. ZR90: You can also connect a
TV via S-video terminal.
❍ When you use the built-in microphone, you can either connect a TV via AV
terminal to check the picture, or headphones to check the sound. ZR90: When
you connect a TV via S-video terminal, you can check the picture on the TV
screen and the sound with headphones connected to the camcorder.
❍ Set the zero set memory at the end of the scene you wish to dub audio. The
camcorder will automatically stop audio dubbing at that point.
Playing Back the Added Sound
You can select to play back Stereo 1 (original sound), Stereo 2 (added sound), or adjust
the balance of both sounds.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
AUDIO SETUP
12bit AUDIO•••STEREO1
(
39)
1. Open the menu and select [AUDIO SETUP]. Select [12bit AUDIO], select
a setting and close the menu.
• STEREO 1: Plays back the original sound.
• STEREO 2: Plays back the added sound.
• MIX/FIXED: Plays back stereo 1 and stereo 2 in the same level.
• MIX/VARI.: Plays back stereo 1 and stereo 2. The mix balance can be adjusted.
2. If you have selected [MIX/VARI.], adjust the mix level: Open the menu
and select [AUDIO SETUP]. Select [MIX BALANCE], adjust the balance
with the SET dial and close the menu.
Turn the SET dial down to increase the volume of Stereo 1 and up to increase the
volume of Stereo 2.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ The camcorder resets to [STEREO 1] when you turn the camcorder off.
However, the mix balance is memorized by the camcorder.
❍ You can also press the 12bit AUDIO OUT button on the wireless controller to
select the audio output. However, the mix balance can only be adjusted in the
menu.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer Using a DV (IEEE1394) Cable
You can transfer recordings to a computer equipped with a DV (IEEE1394) terminal or
IEEE1394 capture board. Optional software is required for transferring recordings
from the tape to a computer. Refer to the instruction manual of the software.
E
DV terminal
DV
IEEE1394 (DV) terminal
Commercially available DV cable
6-pin
4-pin
❍ Operation may not work correctly depending on the software and the
specifications/settings of your computer.
❍ If the computer freezes while you have connected the camcorder, disconnect
and reconnect the DV cable. If the problem persists, disconnect the interface
cable, turn off camcorder and computer, turn camcorder and computer back
on and reconnect them.
❍
Do not disconnect the DV cable, open the memory card cover,
remove the memory card, change the position of the POWER switch or turn off
the camcorder and computer while data is being transferred to the computer
(while the camcorder’s card access indicator is flashing). Doing so may damage
the memory card’s data.
❍
The image files on your memory card and the image files saved
on the hard disk drive of your computer are valuable, original data files. If you
wish to use image files on your computer, make copies of them first, and use
the copied file, retaining the original.
❍ We recommend powering the camcorder from a household power source
while it is connected to the computer.
❍ Refer also to the instruction manual of the computer.
❍
Users of Windows XP can use the DV Network Software
contained on the DIGITAL VIDEO SOLUTION DISK For Windows. For details,
refer to the DV Network Software Instruction Manual.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Inserting and Removing a Memory Card
You can use
SD Memory Cards or
Terminals
commercially available MultiMediaCards with
this camcorder. The SD Memory Card has a
protect switch to prevent accidental erasure.
Inserting the Card
1. Turn off the camcorder.
2. Open the cover.
3. Insert the memory card all the way
into the memory card slot.
4. Close the cover.
Do not close the cover forcefully without
having the card correctly inserted.
Removing the Card
Do not forcefully remove the memory card without first pushing it in.
1. Turn off the camcorder.
Make sure that the card access indicator is
not flashing before you turn off the
camcorder.
Card access
indicator
2. Open the cover.
3. Push the memory card to release it.
Remove the memory card.
4. Close the cover.
❍ This camcorder is compatible with SD Memory Cards or MultiMediaCards only.
Do not use any other types of memory cards.
❍ Turn off the camcorder before inserting or removing the memory card.
Otherwise, it may result in data damage.
❍ If you use memory cards other than the supplied one, make sure to format
them with the camcorder (
117).
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Image Quality/Size
Changing the Still Image Quality
You can choose between Superfine, Fine and Normal.
E
CAMERA
CARD PLAY
PLAY (VCR)
CARD CAMERA
CARD SETUP
IMG QUALITY••FINE
(
39)
Open the menu and select [CARD SETUP]. Select [IMG QUALITY], set it to
[SUPER FINE] or [NORMAL] and close the menu.
Changing the Still Image Size
You can choose between 1024 × 768 pixels and 640 × 480 pixels.
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
CARD SETUP
IMAGE SIZE•••1024× 768
(
39)
Open the menu and select [CARD SETUP]. Select [IMAGE SIZE], set it to
[640 × 480] and close the menu.
❍ Still images are compressed and recorded in the JPEG (Joint Photographic
Experts Group) format.
❍ Estimated Capacity of an 8 MB Memory Card:
640 × 480
Image Size
1024 × 768
No. of
Images
File Size
per Image
No. of
Images
File Size
per Image
Image Quality
Superfine
Fine
13
440 KB
300 KB
160 KB
34
175 KB
120 KB
65 KB
20
50
Normal
38
84
These figures are approximate. They vary according to the recording condition and the
subject. Sample images already recorded on the supplied SD Memory Card are to be
included in the total number.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Movie Size
You can choose between 320 × 240 pixels and 160 × 120 pixels.
CAMERA
CARD PLAY
PLAY (VCR)
CARD CAMERA
CARD SETUP
MOVIE SIZE•••320×240
(
39)
Open the menu and select [CARD SETUP]. Select [MOVIE SIZE], set it to
[160×120] and close the menu.
❍ Movies are recorded in the Motion JPEG format.
❍ Maximum recording time on a 8MB SD Memory Card:
Max. Recording
Time (8 MB)
Image Size
File Size per Second
320 × 240
160 × 120
approx. 20 sec.
approx. 50 sec.
250 KB/sec.
120 KB/sec.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
File Numbers
Images are automatically assigned file numbers from 0101 to 9900 and stored in
folders containing up to 100 images. Folders are assigned numbers from 101 to 998.
(The sample images on the supplied memory card are saved in the [100canon] folder.)
E
You can choose to use consecutive file numbers (CONTINUOUS) or to reset the file
number each time a different memory card is inserted (RESET). We recommend setting
the file numbers to CONTINUOUS.
RESET
The file number will be reset each time a new memory card is
inserted, starting with 101-0101. If the memory card already
contains image files, the consecutive file number will be assigned.
CONTINUOUS
The camcorder memorizes the file number of the last image and
assigns the consecutive file number to the next image, even when a
new memory card is inserted. (If a higher file number already exists
on the memory card, the consecutive number will be assigned.)
There will be no duplication of file numbers. This is useful for
organizing images on a computer.
When you record 3 images.
101-0101
101
101-0102
CONTINUOUS
RESET
101-0103
When you replace the memory
card and record an image.
101-0104
101-0101
101
101
CAMERA
CARD PLAY
PLAY (VCR)
CARD CAMERA
CARD SETUP
FILE NOS.••••CONTINUOUS
(
39)
To change the setting, open the menu and select [CARD SETUP]. Select
[FILE NOS.], set it to [RESET] and close the menu.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Still Images on a Memory Card
You can record still images with the camcorder, from a tape in the camcorder or from
devices connected via the DV terminal or AV terminal. You can also record a still
image on the memory card while you record a movie on the tape.
PHOTO button
Card access
indicator
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
1. Set the camcorder to CARD CAMERA mode.
A white focusing frame appears in the center of the screen. The camcorder will focus on
the subject in the center of the screen. To change the focusing point, see Selecting the
Focusing Point (
103).
2. Press the PHOTO button halfway.
• F and focusing frame turn green when focus is adjusted. The
beep sounds twice. The picture may appear out of focus for a
moment while the camcorder is focusing.
• Exposure is locked.
•
When you press the PHOTO button on the wireless controller, recording starts
immediately.
3. Press the PHOTO button fully.
• F and focusing frame disappear and you hear a shutter sound.
• The card access indicator flashes and the card access display
appears.
• The still image shown on the screen will be recorded on the
memory card.
❍ Do not turn off the camcorder, change the position of the TAPE/CARD switch,
disconnect the power source, open the memory card cover or remove the
memory card while the card access indicator is flashing. Doing so could result
in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch is
set to allow recording.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ To use the self-timer (
58), press the
(self-timer) button before step 2
and press the PHOTO button fully.
❍ When the subject is too bright (overexposed), use the optional FS-30.5U ND
filter.
❍ When the Focus-Priority mode is set to [ON]:
E
When you press the PHOTO button fully before F and focusing frame turn
green, it may take up to 2* seconds until focus is adjusted and the still image
can be recorded to the memory card.
* Up to 4 seconds in the Low Light and the Night modes.
If the subject is not suitable for autofocus, the focusing frame turns yellow and
locks the focus. Adjust the focus manually with the SET dial.
❍ When the Focus-Priority mode is set to [OFF]:
No focusing frame appears.
In step 2, F turns green, and focus and exposure are locked.
❍ The camcorder shuts off when you do not operate it for 5 minutes to save
power. “
AUTO POWER OFF” appears 20 seconds before shutoff. To
continue recording, turn the POWER switch to OFF and then back to CAMERA.
Recording a Still Image on a Memory Card While Recording
Movies on a Tape
When you are recording a movie on a tape, you can record the same picture as a still
image on the memory card.
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
CAMERA SETUP
PHOTO REC••••TAPEb
(
39)
1. Open the menu and select [CAMERA SETUP]. Select [PHOTO REC], set it
to [CARD ] and close the menu.
2. While you are recording a movie, press the PHOTO button.
❍ The size of the still image will be 640 × 480.
❍ The quality of the still image is slightly lower than a still image recorded in
CARD CAMERA mode.
❍ The still image cannot be recorded on a memory card when a fader, effect or
the multi-image screen is activated.
❍ The still image cannot be recorded on a memory card when the 16:9 format is
selected.
❍ Card mix cannot be used.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from a Tape in the Camcorder
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Play back the tape.
2. Press the PHOTO button halfway when the scene you wish to record
appears.
• The camcorder pauses playback. The remaining image capacity and other information
appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
3. Press the PHOTO button fully.
• The card access indicator flashes.
• You can also record a still image by pressing the PHOTO button fully when the tape is
in playback pause mode.
Recording from Other Video Devices
You can record images from devices connected via the S-video terminal (ZR90) or AV
terminal (analog line-in function), or via the DV terminal as still images on a memory
card. For connecting instructions, refer to page 36 and 80.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Set the camcorder to PLAY (VCR) mode.
• If a cassette is loaded, make sure that the tape is stopped.
• When recording via the AV terminal, make sure that “AV \DV” is displayed on the
screen. When recording via the DV terminal, make sure that “AV \DV” is not
displayed. Change the setting as necessary (
85).
2. Connected device: Load a recorded cassette and play back the tape.
3. Press the PHOTO button halfway when the scene you wish to record
appears.
• The still image, remaining image capacity and other information appear.
• When you press the PHOTO button on the wireless controller, recording starts
immediately.
4. Press the PHOTO button fully.
The card access indicator flashes.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
When recording from a tape in the camcorder or other video devices:
❍ A still image recorded from an image in 16:9 format will be vertically
compressed.
❍ The data code of the still image will reflect the date and time it has been
recorded on the memory card.
E
❍ The size of the still image will be 640 × 480.
Screen Displays during Still Image Recording
w Remaining Card Capacity for
q
w
Still Images
e
flashing in red: No card
in green: 6 or more images
in yellow: 1 to 5 images
in red: No more images
• The indication may not decrease
even though a recording has been
made, or may decrease by 2 images
at once.
• All indicators are displayed in green
when a memory card is played back.
q Still Image Quality
Indicates the image quality of the still
image.
"e" Card Access Display
Indicates that the camcorder is writing
on the memory card.
e Image Size
Indicates the still image size.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Reviewing a Still Image Right after Recording
You can select to display a still image for 2, 4, 6, 8 or 10 seconds after it has been
recorded.
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
CAMERA SETUP
REVIEW•••••••2sec
(
39)
Open the menu and select [CAMERA SETUP]. Select [REVIEW], select a
setting option and close the menu.
❍ A still image is displayed as long as you hold the PHOTO button after
recording.
❍ The FILE OPERATION menu appears when you press the SET dial while you are
reviewing a still image, or when you press the SET dial right after recording. In
this menu, you can protect (
109) or erase (
110) the image.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Motion JPEG Movies on a Memory Card
You can record Motion JPEG movies with the camcorder, from a tape in the camcorder
or from devices connected via the DV terminal or the AV terminal. The sound of a
movie recorded on a memory card will be monaural.
E
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
1. Press the start/stop button to begin recording.
WER
O
POWER
A
• You can keep recording until "CARD FULL" appears (max. 60
minutes).
ER
M
A
C
F
F
O
)
TR
(V
Y
LA
P
• With MultiMediaCards, the recording time is limited to 10 sec.
in 320 × 240 pixels and 30 sec. in 160 × 120 pixels.
2. Press the start/stop button to stop recording.
❍ Do not turn off the camcorder, change the position of the TAPE/CARD switch,
disconnect the power source, open the memory card cover or remove the
memory card while the card access indicator is flashing. Doing so could result
in data damage.
❍ When you are using a SD Memory Card, make sure that the protect switch is
set to allow recording.
❍ Do not load/unload a cassette during recording.
❍ We recommend using a SD Memory Card right after you have formatted it
with this camcorder. Recording may be interrupted when you use memory
cards with slow writing speed, or when recording and erasing has been
repeatedly performed on a memory card.
❍ To use the self-timer (
58), press the
(self-timer) button before step 2
and press the start/stop button.
❍ You can select the focusing point when recording a movie on the memory
card.
Recording from a Tape in the Camcorder
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Play back the tape.
2. Press the start/stop button when the scene you wish to record appears.
3. Press the start/stop to stop recording.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording from Other Video Devices
You can record movies from devices connected via the S-video terminal or AV terminal
(analog line-in function), or via the DV terminal on a memory card.
For connecting instructions, refer to page 36 and 80.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
1. Set the camcorder to PLAY (VCR) mode.
• If a cassette is loaded, make sure the tape is stopped.
• When recording via the AV terminal, make sure that “AV \DV” is displayed on the
screen. When recording via the DV terminal, make sure that “AV \DV” is not
displayed. Change the setting as necessary (
85).
2. Connected device: Load a recorded cassette and play back the tape.
3. Press the start/stop button when the scene you wish to record appears.
4. Press the start/stop button to stop recording.
When recording from a tape in the camcorder or other video devices:
❍ A movie recorded from an image in 16:9 format will be vertically compressed.
❍ The data code of the movie will reflect the date and time it has been recorded
on the memory card.
❍ Recording stops at blank sections or recordings in different audio mode
(12bit/16bit).
Screen Displays during Movie Recording
e Image Size
q
w
Indicates the movie size.
e
r Remaining Card Capacity for
Movies
r
Indicates the remaining time in hours
and minutes. At less than 1 minute, the
remaining time will be displayed in 10
second-steps, at less than 10 seconds in
1 second-steps.
q "e" Card Access Display
• The indication varies depending on
the recording condition. The actual
remaining time may be longer or
shorter than indicated.
Indicates that the camcorder is writing
on the memory card.
w Movie recording time
Indicates the recording time of the movie.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Focusing Point
The subject you wish to record is not always in the center of the screen. In the Focus-
Priority mode, you can choose from one of three focusing points to automatically put
the subject you wish into sharp focus.
E
When the program selector is set to [, the Focus-Priority becomes set to ON (only the
center focusing point is available).
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
1. Set the program selector to Q.
2. Turn the SET dial to display all focusing frames.
Three focusing frames appear on the screen, one of it in green.
3. Turn the SET dial to select the focusing point.
Turn the SET dial up to select the frame to the right, down to select the frame to the
left.
❍ The focusing frame gives an indication of the focusing point. Depending on
the size of the subject or the distance, the camcorder may focus outside the
frame.
❍ When you operate the zoom lever, the frames other than the selected one
disappear.
❍ The focusing point can be selected only when Focus-Priority is set to [ON] in
CARD CAMERA mode.
❍ The focusing point returns to the center if you turn off the camcorder, change
from CARD CAMERA mode or move the program selector to [.
❍ The focusing point cannot be selected in the following cases:
-
When using the digital zoom. When you zoom into the digital zoom range,
the focusing frame flashes for 4 seconds and disappears. When you return
to the optical zoom range, the focusing frame reappears.
In Stitch Assist mode.
-
Turning Off the Focus-Priority Mode
Turn off the Focus-Priority mode if you wish to put timing ahead of focus.
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
CAMERA SETUP
FOCUS PRI.•••ON
(
39)
Open the menu and select [CAMERA SETUP]. Select [FOCUS PRI.], set it to
[OFF] and close the menu.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording Panoramic Images (Stitch Assist Mode)
You can shoot a series of overlapping images and merge them into one large
panoramic scene using the supplied software (PhotoStitch) on a computer.
CARD +/– button
PHOTO button
button
When Recording in Stitch Assist Mode:
PhotoStitch detects the overlapping portion of adjoining images and merges them. Try
to include a distinctive item (landmark, etc.) in the overlapping portion.
CAMERA
PLAY (VCR)
CARD PLAY
CARD CAMERA
1. Press the
button.
CARD MIX /
SLIDE SHOW/
REC PAUSE
/
2. Select the direction with the CARD +/– button.
CARD + button: clockwise. CARD – button: counterclockwise.
CARD
3. Select the program AE mode and zoom on the subject.
Adjust focus and AE shift manually as necessary. Once the sequence has started, you
cannot change the program AE mode, AE shift, zoom or focus.
4. Press the PHOTO button to record the first image.
Direction and number of recorded images appear.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Record the second image so that it overlaps a portion of the first image.
• Minor discrepancies in the overlapped area can be corrected with the software.
• You can retake an image by pressing the CARD +/– button to return to the previous
image.
E
• A maximum of 26 images can be recorded.
6. Press the
button after the last image.
For details on how to merge these images, refer to the Digital
Video Software Instruction Manual.
CARD MIX /
SLIDE SHOW/
REC PAUSE
/
❍ Compose each image so that it overlaps 30 to 50% of the adjoining image. Try
to keep the vertical misalignment within 10%.
❍ Do not include moving subject in the overlapping portion.
❍ Do not try to stitch images that include both distant and close subjects. They
may appear warped or doubled up.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing Back a Memory Card
You can display a single image, 6 at one time (index screen
107), or one after
another (slide show
107). Use the Card Jump function to quickly locate an image
without displaying them one by one (
108).
CARD – button
CARD + button
CARD
3 button
e/a button
SLIDE SHOW button
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. Set the camcorder to CARD PLAY mode.
2. Press the CARD +/– button to move between images.
CARD
3. To play back a movie, press the e/a button.
• The first scene appears as a still image when playback is
complete.
• Pressing the e/a button during playback pauses the playback.
Press the e/a button again to restart playback.
• Pressing the 3 button displays the first scene of the movie.
• Press the CARD +/- button (or the REW `/FF 1 button on the wireless controller)
for 8× fast forward/fast rewind playback.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ Images not recorded with this camcorder, uploaded from a computer (except
the sample images 113), edited on a computer and images whose file
names have been changed may not be played back correctly.
❍ Do not turn off the camcorder, change the position of the TAPE/CARD switch,
disconnect the power source, open the memory card cover or remove the
memory card while the card access indicator is flashing. Doing so could result
in data damage.
E
Slide Show
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. Press the SLIDE SHOW button.
Images are played back one after another.
CARD MIX /
SLIDE SHOW/
REC PAUSE
/
2. Press the SLIDE SHOW button to stop the slide show.
Index Screen
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. Move the zoom lever toward W.
Up to 6 images appear.
2. Turn the SET dial to select an image.
• Move the
to the image you wish to view.
• You can switch between the index pages by pressing the CARD
+ or CARD – button.
3. Move the zoom lever toward T.
The index screen is cancelled and the selected image is displayed.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Card Jump Function
You can locate images without displaying them one by one. The number in the upper
right of the screen indicates the image number of the current image by the total
number of images.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
Press and hold the CARD + or CARD – button.
When you release the button, the image of the displayed image
number appears.
CARD
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Protecting Images
You can protect important images from accidental erasure when displaying a single
image or index screen.
E
If a memory card is formatted, all still images and movies, even protected ones,
will be erased permanently.
❍ The sample images recorded on the supplied SD Memory Card are already
protected.
❍ Movies can only be protected when the first scene is displayed as a still image.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. Select the image you wish to protect.
2. Press the SET dial to open the FILE OPERATION menu.
In CARD CAMERA mode, the menu appears when you press the SET dial while you are
reviewing a still image, or when you press the SET dial right after recording.
3. Select [PROTECT
].
• “ ” appears and now the image cannot be erased.
• To cancel the protection, press the SET dial.
4. Select [bRETURN] to close the menu.
Protecting during Index Screen Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
CARD OPERATIONS
PROTECT
(
39)
1. Move the zoom lever toward W.
• Up to 6 images appear.
• Select the image you wish to protect.
2. Open the menu and select [CARD OPERATIONS]. Select [\PROTECT
]
and press the SET dial.
• “
” appears on the image.
• To cancel the protection, press the SET dial.
3. Close the menu.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing Images
You can erase images singly or all at once.
Be careful when erasing images. Erased images cannot be recovered.
❍ Protected images cannot be erased.
❍ Movies can only be erased when the first scene is displayed as a still image.
Erasing a Single Image
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. Select the image you wish to erase.
2. Press the SET dial to open the FILE OPERATION menu.
In CARD CAMERA mode, the menu appears when you press the SET dial while you are
reviewing a still image, or when you press the SET dial right after recording.
3. Select [IMAGE ERASE].
• “ERASE THIS IMAGE?”, [NO] and [YES] appears.
• If an image is protected, [YES] appears in purple.
4. Select [YES].
The image is erased and the previous image appears.
5. Select [bRETURN] to close the menu.
Erasing a Single Image/All Images
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
CARD OPERATIONS
IMAGE ERASE
(
39)
1. Open the menu and select [CARD OPERATIONS].
2. Select [IMAGE ERASE].
3. Select [SINGLE] or [ALL].
• When erasing a single image: “ERASE THIS IMAGE?” [NO] and [YES] appears. If an
image is protected, [YES] appears in purple.
• When erasing all images: “ERASE ALL IMAGES? [EXCEPT FOR
and [YES] appears.
IMAGES]”, [NO]
4. Select [YES] and close the menu.
• When erasing a single image: The image is erased and the previous image appears. To
erase another image, select the image with the CARD +/– button and select [YES].
• When erasing all images: All still images or movies with exception of the protected ones
are erased.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Combining Images (Card Mix)
You can produce effects not possible with just a tape with the Card Mix function.
Choose one of the sample images provided on the supplied SD Memory Card (such as
picture frames, backgrounds and animations) and combine it with the live video
recording.
E
Card Chroma Key (CARD CHROMA)
Combines frames with your recordings. The live video recording will appear in place of
the blue area of the card mix image.
Mix level adjustment: blue area of the still image.
Live video recording
Card mix image
Card Luminance Key (CARD LUMI.)
Combines illustrations or title with your recordings. The live video recording will
appear in place of the light area of the card mix image.
Mix level adjustment: light area of the still image.
Live video recording
Card mix image
Camera Chroma Key (CAM. CHROMA)
Combines backgrounds with your recordings. Record your subject in front of a blue
curtain, and the subject not blue will be superimposed on the card mix image.
Mix level adjustment: blue area of the live video recording.
Live video recording
Card mix image
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Card Animation (C. ANIMATION)
Combines animations with your recordings. You can choose from 3 types of card
animation effects.
• Corner: Animation appears on the upper left and the lower right corner of the screen.
• Straight: Animation appears on the top and bottom of the screen and moves to the right
and left.
• Random: Animation moves randomly in the display.
Mix level adjustment: blue area of the card animation image.
Live video recording
Card mix image
CARD + / – button
Program selector
CARD MIX button
SET dial
MENU button
PLAY (VCR)
CARD CAMERA
CARD PLAY
CAMERA
CARD MIX
MIX TYPE•••••CARD CHROMA
(
39)
–
+
MIX LEVEL••••
1. Set the program selector to Q.
2. Open the menu and select [\CARD MIX].
The card mix menu appears.
3. Select the image you wish to combine with the CARD +/– button.
4. Select [MIX TYPE].
[CARD CHROMA], [CARD LUMI.], [CAM. CHROMA] and [C. ANIMATION] appears.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select the mix type matching the sample image you have selected.
• The screen shows the combined image.
• When you have selected [C. ANIMATION], select [ANIMAT. TYPE] and select between
[CORNER], [STRAIGHT] and [RANDOM].
E
6. To adjust the mix level, select [MIX LEVEL] and adjust it with the SET
dial.
7. Close the menu.
“CARD MIX” flashes.
8. Press the CARD MIX button.
• “CARD MIX” stops flashing.
• The combined image appears.
❍ Card mix cannot be used when [PHOTO REC] is set to [CARD ].
❍ Movies recorded on a memory card cannot be combined with camcorder
recordings.
❍ Additional sample images are provided on the supplied DIGITAL VIDEO
SOLUTION DISK. Refer to Adding Still Images from Your Computer to the
Memory Card in the Digital Video Software Instruction Manual.
Sample Images
Following sample images are pre-recorded on the supplied SD Memory Card.
Card Chroma Key
Card Luminance Key
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Chroma Key
Card Animation
The sample images recorded on the supplied SD Memory Card are intended only
for the personal use with this camcorder. Do not use these sample images for
other purposes.
If you have mistakenly erased the sample images on the supplied SD Memory
Card, they can be downloaded from the homepage http://www.canondv.com.
For details on how to add the downloaded images to the memory card, refer to
Adding Still Images from Your Computer to the Memory Card in the Digital Video
Software Instruction Manual.
PhotoEssentials – Royalty Free Stock Photography
The PhotoEssentials suite of royalty-free images on CD-ROM features premium quality assignment
photography and is ideally suited for use in advertising, brochures, reports, multimedia, websites,
books, packaging and more.
For more information, please visit their website www.photoessentials.com
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying Still Images
You can copy still images from tape to memory card, or from memory card to tape. All
still images from the selected still image onward will be copied.
E
Copying Still Images from Tape to Memory Card
Insert a memory card with enough remaining capacity, and load a recorded cassette.
CAMERA
CARD CAMERA
CARD PLAY
PLAY (VCR)
[
COPY
]
CARD OPERATIONS
(
39)
1. Locate the still image you wish to copy on the tape
and stop the tape shortly before the still image.
CARD
To copy all still images from the tape, rewind the tape to the
beginning.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [b \ ] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• The still image being copied is shown on the screen.
• Copying stops when the tape reaches the end or the memory card is full (“CARD
FULL” appears).
5. Press the 3 (stop) button to end copying.
❍ The size of a still image copied from tape to memory card will be 640 × 480.
❍ The data code of the still image reflects the date and time it has been copied.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Copying Still Images from Memory Card to Tape
Load a cassette with enough free space, and insert a recorded memory card. Make
sure that the protect tab on the cassette is set to allow recording.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
[
COPY
]
CARD OPERATIONS
(
39)
1. Select the first still image you wish to copy with the
CARD +/– buttons.
CARD
To copy all still images from the memory card, select the first still
image.
2. Open the menu and select [CARD OPERATIONS].
3. Select [COPY [
\b] ].
[CANCEL] and [EXECUTE] appears.
4. Select [EXECUTE].
• “NOW COPYING” appears.
• It takes about 6 seconds per still image to be copied to the tape.
• Copying stops when all still images are copied or the tape is full.
5. Press the 3 (stop) button to end copying.
The data code of the still image reflects the date and time it has been copied.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Formatting a Memory Card
Format new memory cards, or when you get the message “CARD ERROR”. You can
also format a memory card to erase all data recorded on it.
E
❍ Formatting a memory card erases all data, including protected images.
❍ Images erased by formatting cannot be recovered.
❍ If you use a memory card other than the supplied one, format it with the
camcorder.
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
CARD OPERATIONS
FORMAT
(
39)
1. Open the menu and select [CARD OPERATIONS].
2. Select [FORMAT].
[CANCEL] and [EXECUTE] appears.
3. Select [EXECUTE].
[ALL DATA WILL BE ERASED. FORMAT THIS CARD?], [NO] and [YES] appears.
4. Select [YES] and close the menu.
• Formatting starts.
• Selecting [NO] brings you back to step 3.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a Computer Using a USB Cable
You can download images from the memory card to a computer using the supplied
USB cable.
“PC CONNECT
” appears to indicate that the camcorder is
connected to the computer via USB cable.
❍ Do not disconnect the USB cable, open the memory card cover, remove the
memory card, change the position of the TAPE/CARD switch or turn off the
camcorder and computer while data is being transferred to the computer
(while the camcorder's card access indicator is flashing). Doing so may damage
the memory card’s data.
❍ Operation may not work correctly depending on the software and the
specifications/settings of your computer.
❍ The image files on your memory card and the image files saved on the hard
disk drive of your computer are valuable, original data files. If you wish to use
image files on your computer, make copies of them first, and use the copied
file, retaining the original.
❍ We recommend powering the camcorder from a household power source
while it is connected to the computer.
❍ Refer also to the computer instruction manual.
❍ Images recorded on a tape cannot be transferred to a computer via USB
interface.
❍ Users of Windows XP and Mac OS X:
Your camcorder is equipped with the standard Picture Transfer Protocol (PTP)
allowing you to download still images (JPEG only) by simply connecting the
camcorder to a computer via USB cable without installing the software from
the DIGITAL VIDEO SOLUTION DISK.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Creating a Start-up Image
You can create 2 start-up images using still images on the memory card.
E
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
MY CAMERA
CREATE START–UP IMAGE
(
39)
1. Select a still image with the CARD +/– buttons.
2. Open the menu and select [MY CAMERA].
3. Select [CREATE START-UP IMAGE].
[SET THIS AS START-UP IMAGE?], [YES] and [NO] appears.
4. Select [YES].
[SAVE AS MY IMAGE1], [MY IMAGE2] and [CANCEL] appears.
5. Select [MY IMAGE1].
[OVERWRITE MY IMAGE1?], [NO] and [YES] appears.
6. Select [YES].
The still image will be saved, and the image that was saved to [MY IMAGE1] is erased.
Retain the original data of the still image you have set as the start-up image on
your computer or removable disk.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing Still Images
You can print still images by connecting the camcorder to a printer with Direct Print
function. You can also use the print order settings for direct printing (
Following printers can be connected to your camcorder:
126).
Canon Printers
PictBridge compliant CP Printer
Bubble Jet Direct compatible Printer
PictBridge compliant Bubble Jet Printer
PictBridge compliant non-Canon Printer
Connecting the Printer to the Camcorder
R
E
W
O
P
A
ER
M
CA
FF
O
)
CR
A
Y
(V
PL
Printer with
direct print function
1. Turn off the camcorder and insert a memory card that contains still images.
2. Turn on the printer.
3. Set the camcorder to CARD PLAY mode.
4. Connect the camcorder to the printer using the cable.
appears and changes to
or
when the printer is properly connected
to the camcorder. (Does not appear with movies, or still images that cannot be played
back with the camcorder.)
If
continues to flash (for more than 1 minute), the camcorder is not correctly
connected to the printer. In such case, disconnect the cable from camcorder and
printer, turn off camcorder and printer, turn both back on and reconnect the
camcorder to the printer.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ Refer to the instruction manual of each printer for information on which
interface cable to use with the camcorder.
❍ We recommend powering the camcorder from a household power source.
❍ Refer also to the instruction manual of the respective printer.
❍ The print setting menu may differ slightly depending on the connected printer.
E
Printing
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. During still image playback, select the still image you wish to print and
press the SET dial.
• The print setting menu appears.
• Depending on the printer, the message “BUSY.” may appear before the camcorder
displays the print setting menu.
2. Make sure that [PRINT] is selected and press the SET
dial.
Printing starts. The print setting menu disappears when printing
is complete.
❍ Observe the following precautions during printing, otherwise printing may not
be performed correctly.
-
-
-
-
Do not turn off the camcorder or the printer.
Do not change the position of the TAPE/CARD switch.
Do not detach the cable.
Do not open the memory card cover or remove the memory card.
❍ Images not recorded with this camcorder, uploaded from a computer, edited
on a computer and images whose file names have been changed may not be
printed correctly.
❍ Cancel Printing
Press the SET dial while "NOW PRINTING" is displayed. A confirmation dialog
appears. Select [OK] and press the SET dial. Printing stops even if it is
incomplete and the paper is fed through.
❍ Printing Errors
If an error occurs during the printing process, an error message appears
(
133).
-
Canon printer: With most errors, printing resumes automatically after you
correct the error. If the error persists, press the SET dial to cancel printing.
Refer also to the printer manual for details.
If the error still persists and printing does not restart, follow below
procedure:
-
1. Disconnect the cable.
2. Turn the POWER switch of the camcorder to OFF and back to PLAY (VCR).
3. Reconnect the cable.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ When you have finished printing:
1. Disconnect the cable from the camcorder and printer.
2. Turn off the camcorder.
Selecting the Number of Copies
A maximum of 99 copies can be selected for one still image.
1. In the print setting menu, turn the SET dial to select
(COPIES) and press the SET dial.
2. Turn the SET dial to select the number of copies and
press the SET dial.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the Print Settings (Paper/Style)
Check which print setting menu your camcorder displays and move to the respective
section. The print setting options vary depending on the printer.
E
Setting the Print Style q (
123) Setting the Print Style w (
125)
Icon that appears when
connecting the printer
Print Setting Menu
Paper Size
h
h
h
h
h
h
h
i
h
i
i
i
Paper Type
Borders
Multiple print (8-UP)
Print effect (Image Optimize)
Date
h: Available ×: Not available
❍ Bordered: The image area remains relatively unchanged from the recorded
image when it is printed.
❍ Borderless/multiple print: The center portion of the recorded image is printed at
an enlarged size. The image’s top, bottom and sides may be cropped slightly.
❍ [8-UP] can be selected when using card size paper (5.3 x 8.6 cm) with
PictBridge compliant CP Printers.
❍ Date print cannot be selected with the CP Printers CP-200 and CP-300.
Setting the Print Style q
The default setting and setting options vary depending on the printer. Refer to the
instruction manual of the printer.
Paper Settings
1. In the print setting menu, turn the SET dial to select
[PAPER] and press the SET dial.
123
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Turn the SET dial to select the paper size and press
the SET dial.
3. Turn the SET dial to select the paper type and press
the SET dial.
4. Turn the SET dial to select a layout option and press
the SET dial.
Setting the Print Effect (Image Optimize)
This function uses the camcorder's recording information to optimize the image data,
yielding high quality prints.
1. In the print setting menu, turn the SET dial to select
(print effect) and press the SET dial.
2. Turn the SET dial to select a setting and press the
SET dial.
Including the Date in the Print
1. In the print setting menu, turn the SET dial to select
(date) and press the SET dial.
124
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Turn the SET dial to select a date print option and
press the SET dial.
E
Setting the Print Style w
Paper Size
CARD #1*, CARD #2*, CARD #3*, LTR, A4
For details on paper type, refer to the Bubble Jet Printer
User Guide.
Borders Borderless Prints right to the edges of the page.
Bordered Prints with a border.
* Recommended paper size
1. In the print setting menu, turn the SET dial to select
[STYLE] and press the SET dial.
2. Make sure that (paper) is selected and press the
SET dial.
3. Turn the SET dial to select the paper size and press
the SET dial.
Pressing the MENU button brings you back to the print settings
menu.
4. Turn the SET dial to select
the SET dial.
(borders) and press
5. Turn the SET dial to select a borders option and
press the SET dial.
Pressing the MENU button brings you back to the print settings
menu.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Printing with Print Order Settings
You can select still images for printing and set the number of copies. These print order
settings are compatible with the Digital Print Order Format (DPOF) standards and can
be used for printing on DPOF compatible printers (
images can be selected.
120). A maximum of 200 still
Selecting Still Images for Printing (Print Order)
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
1. Select the still image you wish to print.
2. Press the SET dial to open the FILE OPERATION menu.
3. Select [ PRINT ORDER].
4. Select the number of copies.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
5. Select [bRETURN] to close the menu.
Selecting in Index Screen Display
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
CARD OPERATIONS
PRINT ORDER
(
39)
1. Move the zoom lever toward W.
• Up to 6 images appear.
• Select the image you wish to print.
2. Open the menu and select [CARD OPERATIONS]. Select [\ PRINT
ORDER].
3. Press the SET dial and set the number of copies with the SET dial.
• “ ” appears on the image.
• To cancel the print order, set the number of copies to 0.
4. Close the menu.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing All Print Orders
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
E
CARD OPERATIONS
PRINT ORDERS ALL ERASE
(
39)
1. Open the menu and select [CARD OPERATIONS].
2. Select [ PRINT ORDERS ALL ERASE].
“ERASE ALL
PRINT ORDERS?”, [NO] and [YES] appears.
3. Select [YES].
All “ ” disappear.
4. Close the menu.
Printing
CAMERA
PLAY (VCR)
CARD CAMERA
CARD PLAY
PRINT
(
39)
1. Connect the printer to the camcorder (
120).
2. Open the menu and select [\ PRINT].
• The print setting menu appears.
• “SET
PRINT ORDER” appears, when you connect a printer with direct print function
and select [\ PRINT] without having set the print order.
3. Make sure that [PRINT] is selected and press the SET dial.
Printing starts. The print setting menu disappears when printing is complete.
❍ With PictBridge compliant printers, you can set paper settings, print effect and
date print before step 3 (
123).
With Bubble Jet Direct compatible printers, you can set paper settings and date
print before step 3 (
125).
❍ Cancel Printing
Press the SET dial while "NOW PRINTING" is displayed. A confirmation dialog
appears. Select [OK] and press the SET dial. Printing stops even if it is
incomplete and the paper is fed through.
❍ Restarting Printing
Open the CARD PLAY menu and select [\ PRINT]. Select [RESUME] in the
print setting menu and press the SET dial. The remaining images will be
printed.
Printing cannot be restarted in the following cases:
-
-
When you change the print order settings.
When you delete a still image with print order settings.
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Displays
Hiding the Displays on the LCD Screen
You can hide the displays on the LCD screen to have a clear screen for playback.
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY
DISPLAYS•••••ON
DISPLAY SETUP/
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [DISPLAYS], set it to
[OFF <PLAYBK>] and close the menu.
• Warning messages still appear, and the data code appears if turned on.
• Tape operation displays appear for 2 seconds.
•
Displays cannot be hidden on the index screen.
Hiding/Showing the Displays on the TV Screen
When you connect a TV for recording, you can select to show the camcorder displays
on the TV screen. For playback, you can hide the camcorder displays on the TV screen.
PLAY (VCR)
CARD PLAY
CAMERA
CARD CAMERA
TV SCREEN••••ON
DISPLAY SETUP/
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [TV SCREEN], set it
to [OFF] and close the menu.
The displays disappear from the TV screen.
CAMERA
CARD CAMERA
PLAY (VCR)
CARD PLAY
TV SCREEN••••OFF
DISPLAY SETUP/
(
39)
Open the menu and select [DISPLAY SETUP/ ]. Select [TV SCREEN], set it
to [ON] and close the menu.
The displays appear on the TV screen.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Displays during Recording/Playback
CAMERA Mode
E
Image stabilizer ( 79)
Recording reminder ( 27)/
Self-timer countdown ( 58)/
Photo recording timer ( 29)
Zoom ( 30)
Skin detail ( 50)
AE shift ( 51)
Recording mode ( 59)
Tape operation
Program AE ( 46)
Shutter speed ( 56)
Manual focus ( 52)
White balance ( 54)
Card mix ( 111)
Time code
Remaining tape
Remaining battery
charge ( 27)
Digital effects ( 62)
Date and time ( 21)
Condensation
warning ( 136)
Remote sensor mode
(
77)
AF/AE locked in
Photo mode ( 29)
Headphones ( 61)
Wind screen ( 60)
Self-timer ( 58)
Audio mode ( 61)
16:9 mode ( 78)
Backup battery ( 17)
Photo recording ( 29)
PLAY (VCR) Mode
/
/
/
: Fast forward playback/
rewind playback ( 34)
:×2 playback ( 34)
:×1 playback ( 34)
:Slow playback ( 34)
: Playback pause
REC
(
34)
PAUSE
STOP
EJECT
:Date search/photo
search ( 74)
2
1
2
1
/
/
/
/
/
/
/
:Zero set memory
RTN
RTN
FF
(
73)
REW
:Frame advance playback/
frame reverse playback
: AV insert editing
86)
: Audio dubbing
88)
(
(
34)
(
12 bit audio
(
89)
End search ( 72)/
Photo search/
Volume level of built-in
speaker or headphones
Date search ( 74)/
AV insert ( 86)/
(
35)
Audio dubbing ( 88)
DV input ( 83)
Data code ( 70)
129
Download from Www.Somanuals.com. All Manuals Search And Download.
CARD CAMERA Mode
Still image quality ( 93)
Remaining card capacity
for still images ( 99)
Stitch assist ( 104)
Still image size ( 93)
Movie size ( 94)
Focusing frame
103)
Remaining card capacity
for movies ( 102)
(
CARD PLAY Mode
Protect mark ( 109)
File number ( 95)
Slide show ( 107)
Data code ( 70)
Current image/
total images
Length of the movie
Lap time
130
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Messages
Message
SET THE TIME ZONE,
DATE AND TIME
Explanation
E
You have not set the time zone, date and time. This message 21
appears each time you turn the power on until you set the
time zone, date and time.
CHANGE THE
Battery pack is exhausted. Replace or charge the battery
pack.
13
138
16
BATTERY PACK
THE TAPE IS SET FOR
ERASURE PREVENTION position of the protect switch.
Cassette is protected. Replace the cassette or change the
REMOVE THE
CASSETTE
Camcorder stopped operating to protect the tape. Unload
and reload the cassette.
CHECK THE DV INPUT DV cable is not connected, or the connected digital device is
turned off.
80
CONDENSATION HAS Condensation has been detected in the camcorder.
BEEN DETECTED
136
–
TAPE END
Tape reached the end. Rewind the tape or replace the
cassette.
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a
[REC MODE] tape recorded in a mode other than the SP mode.
CHECK THE CASSETTE You attempted to perform audio dubbing on a tape
[AUDIO MODE] recorded in 16-bit or 12-bit 4-channel sound.
86
88
88
CHECK THE CASSETTE You attempted to perform audio dubbing or AV insert on a
86
88
[BLANK]
tape with a blank section.
COPYRIGHT PROTECTED
PLAYBACK IS RESTRICTED
You attempted to play back a copyright protected tape.
83
COPYRIGHT
You attempted to dub a copyright protected tape. May also
83
PROTECTED DUBBING appear when an anomalous signal is received during analog
RESTRICTED
line-in recording, or during analog-digital conversion of a
copyright protected tape.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Card Related Messages
Message
NO CARD
Explanation
Memory card not is inserted into the camcorder.
92
92
THE CARD IS SET FOR SD Memory Card is set for erasure prevention. Replace the
ERASURE PREVENTION card or change the position of the protect switch.
NO IMAGES
No images are recorded on the memory card.
–
–
CARD ERROR
A memory card error occurred. The camcorder cannot record
or play back the image.
The error may be temporary. If the message disappears after
4 seconds and flashes red, turn the camcorder off, remove
the card and reinsert the card. If
can continue recording/playback.
changes to green, you
CARD FULL
No remaining capacity on the memory card. Replace with
another card or erase images.
–
NAMING ERROR
File or folder number has reached the maximum value.
95
–
UNIDENTIFIABLE
IMAGE
Image is recorded in a not compatible JPEG format or
another format not compatible with the camcorder, or the
image file is corrupted.
PRINT ORDER
ERROR
You attempted to set more than 200 still images in the print 126
order.
THIS IMAGE CANNOT Some analog images cannot be recorded on the memory
BE RECORDED card depending on the signal.
–
THIS IMAGE CANNOT You attempted to use an image recorded with another
BE USED AS START-UP camcorder, recorded in a format not compatible with this
119
IMAGE
camcorder, or that has been edited on a computer.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Print Related Messages
Message
Explanation
PAPER ERROR
There is a problem with the paper.
Wrong paper size is inserted, or the ink cannot be used with
the selected paper.
E
NO PAPER
Paper is not correctly inserted or there is no paper.
The paper jammed during printing.
PAPER JAM
PAPER HAS BEEN
CHANGED
Paper size has been changed between print setting and start
of printing.
MEDIA TYPE ERROR
You attempted to use a paper size/type that is not
supported by the printer.
INK ERROR
There is a problem with the ink.
NO INK
The ink cartridge is not inserted or is out of ink.
The ink cartridge needs to be replaced soon.
LOW INK LEVEL
WASTE TANK FULL
Waste tank is full. Refer to the instruction manual of your
printer.
FILE ERROR
You attempted to print an image that was made with
another camcorder, has a different format, or was edited on
a computer.
CANNOT PRINT!
You attempted to print an image that was made with
another camcorder, has a different format, or was edited on
a computer.
COULD NOT PRINT X
IMAGES
You attempted to use the print order settings to print X
images that were made with another camcorder, have a
different format or were edited on a computer.
SET PRINT ORDER
PRINTER ERROR
You attempted to print an image from the CARD PLAY
menu [\ PRINT] without having set the print order.
Cancel printing. Turn off the printer and turn it back on.
Check the printer status.
HARDWARE ERROR
Cancel printing. Turn off the printer and turn it back on.
Check the printer status.
COMMUNICATION
ERROR
The printer is experiencing a data transmission error.
Or, you attempted to print from a memory card that
contains a large number of images. Reduce the number of
images.
PRINTER IN USE
The printer is in use. Check the printer status.
PRINTER WARMING
UP
Printer is warming up. If the message does not disappear
after a few seconds, check the printer status.
PAPER LEVER ERROR
Paper lever error occurred. Adjust the paper selection lever
to the proper position.
PRINTER COVER OPEN Close the printer cover securely.
NO PRINTHEAD No print head is installed in the printer.
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance/Others
Camcorder Handling Precautions
❍ Do not carry the camcorder by the LCD panel or viewfinder.
❍ Do not leave the camcorder in places subject to high temperatures, such as a sun-
heated car, and high humidity.
❍ Do not use the camcorder in places subject to magnetic or electric fields such as
near the TV transmitters or portable communication devices.
❍ Do not point the lens or viewfinder at strong light sources. Do not leave the
camcorder pointed at a bright subject.
❍ Do not use the camcorder in dusty or sandy places. Dust or sand getting inside the
cassette or camcorder may cause damage. Dust and sand can also damage the lens.
Attach the lens cap after use.
❍ The camcorder is not waterproof. Water, mud or salt getting inside the cassette or
camcorder may cause damage.
❍ Be careful of heat generated by lighting equipment.
❍ Do not disassemble the camcorder. If the camcorder does not function properly,
consult qualified service personnel.
❍ Handle the camcorder with care. Do not subject the camcorder to shocks or
vibration as this may cause damage.
❍ Avoid sudden changes in temperature. Moving the camcorder rapidly between hot
and cold temperatures may cause condensation to form on its internal surfaces
(
136).
Storage
❍ If you do not intend to use the camcorder for a long time, store it in a place free of
dust, in low humidity, and at temperatures not higher than 86 ˚F (30 ˚C).
❍ After storage, check the functions of your camcorder to make sure that the
camcorder is still working properly.
Cleaning
Camcorder Body and Lens
❍ Use a soft, dry cloth to clean the camcorder body and lens. Never use chemically
treated cloth or volatile solvents such as paint thinner.
LCD Screen
❍ Clean the LCD screen using a commercially available cleaning cloth for glasses.
❍ Condensation may form on the surface of the screen when the temperature
changes suddenly. Wipe it with a soft dry cloth.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ At cold temperatures, the screen may be darker than usual. This is not a
malfunction. The screen returns to normal when the camcorder warms up.
E
Viewfinder
❍ Move the viewfinder upward. Remove the protect cover
and clean the glass with a cotton swab. Reattach the
protect cover when finished.
❍ Be careful not to scratch the glass when cleaning.
Video Heads
❍ When the playback picture becomes distorted, the video heads need to be cleaned.
❍ To maintain the best picture quality, we recommend cleaning the video heads
frequently with the Canon DVM-CL Digital Video Head Cleaning Cassette or a
commercially available dry cleaning cassette.
❍ Do not use wet type cleaning cassettes as this may damage the camcorder.
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Condensation
Moving the camcorder rapidly between hot and cold temperature may cause
condensation (water droplets) to form on its internal surfaces. Stop using the
camcorder if condensation is detected. Continued use may damage the camcorder.
Condensation may form in the following cases:
When the camcorder is moved from an
air-conditioned room to a warm, humid
place
When the camcorder is moved from a
cold place to a warm room
When the camcorder is left in a humid
room
When a cold room is heated rapidly
How to avoid condensation:
❍ Unload the cassette, place the camcorder in an airtight plastic bag and let it adjust
to temperature changes slowly before removing it from the bag.
When condensation is detected:
❍ The camcorder stops operating and the warning message “CONDENSATION HAS
BEEN DETECTED” appears for approx. 4 seconds and h starts flashing.
❍ If a cassette is loaded, the warning message “REMOVE THE CASSETTE” appears and
v starts flashing. Remove the cassette immediately and leave the cassette
compartment open. Leaving the cassette in the camcorder may damage the tape.
❍ A cassette cannot be loaded when condensation is detected.
Resuming use:
❍ It takes about 1 hour until the water droplets evaporate. After the condensation
warning stops flashing, wait for 1 more hour before resuming use.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Pack Handling Precautions
DANGER!
Treat the battery pack with care.
E
• Keep it away from fire (or it might explode).
• Do not expose the battery pack to temperature higher than 140 ºF (60 ºC). Do
not leave it near a heater or inside a car in hot weather.
• Do not try to disassemble or modify it.
• Do not drop or knock it.
• Do not get it wet.
❍ Charged battery packs continue to discharge naturally. Therefore, charge them on
the day of use, or the day before, to ensure a full charge.
❍ Attach the terminal cover whenever a battery pack is not in use. Contact to metallic
objects may cause a short circuit and damage the battery pack.
❍ Dirty terminals may cause a poor contact between the battery pack and the
camcorder. Wipe the terminals with a soft cloth.
❍ Since storing a charged battery pack for a long time (about 1 year) can shorten its
lifecycle or affect performance, we recommend to discharge the battery pack fully
and to store it in a dry place at temperatures no higher than 86 ˚F (30 ˚C). If you do
not use the battery pack for long periods, charge and discharge it fully at least once
a year. If you have more than 1 battery pack, perform these precautions at the
same time for all battery packs.
❍ Although the battery pack’s operating temperature range is from 32 ˚F to 104 ˚F
(0 ˚C to 40 ˚C), the optimal range is from 50 ˚F to 86 ˚F (10 ˚C to 30 ˚C). At cold
temperatures, performance will temporarily decline. Warm it in your pocket before
use.
❍ Replace the battery pack if the usable time after full charge diminishes substantially
at normal temperatures.
About the battery terminal cover
The battery terminal cover has a [ ]-shaped hole. This is useful when you wish to
differentiate between charged and uncharged battery packs. For example, with
charged battery packs, attach the terminal cover so that the [ ]-shaped hole shows
the blue label.
Back side of the battery pack
Terminal cover attached
Charged
Uncharged
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Cassette Handling Precautions
❍ Rewind tapes after use. If the tape becomes slack and damaged, it may cause picture
and sound distortion.
❍ Return cassettes in the case and store them upright.
❍ Do not leave the cassette in the camcorder after use.
❍ Do not use spliced tapes or nonstandard cassettes as they may damage the camcorder.
❍ Do not use tapes that have been jammed as video heads may become dirty.
❍ Do not insert anything into the small holes of the cassette, or cover them with
cellophane tape.
❍ Handle cassettes with care. Do not drop or subject them to severe impact as this may
damage the cassettes.
❍ Rewind tapes from time to time if they are stored for a long time.
❍ With cassettes equipped with a memory function, metal plated terminals may become
dirty with use. Clean the terminals with a cotton swab after about 10 times of
loading/unloading. The memory function is not supported by the camcorder.
Protecting Tapes from Accidental Erasure
To protect your recordings from accidental
erasure, slide the tab on the cassette to the
left. (This switch position is usually labeled
SAVE or ERASE OFF.)
REC
SAVE
REC
SAVE
If you load a protected cassette in CAMERA
mode, the message “THE TAPE IS SET FOR
ERASURE PREVENTION” appears for approx. 4
seconds and v starts flashing. If you wish to record on that cassette, slide the tab
back to the right.
Memory Card Handling Precautions
❍ Format new memory cards with the camcorder. Memory cards formatted with other
devices such as a computer may not operate correctly.
❍ We recommend saving backups of memory card images on your computer’s hard drive
or other external memory device. Image data may be corrupted or lost due to memory
card defects or exposure to static electricity. Canon Inc. makes no warranties for
corrupted or lost data.
❍ Do not turn off the camcorder, disconnect the power source, open the memory card
cover or remove the memory card while the card access indicator is flashing.
❍ Do not use memory cards in places subject to strong magnetic fields.
❍ Do not leave memory cards in places subject to high humidity and high temperature.
❍ Do not disassemble memory cards.
❍ Do not bend, drop, or subject memory cards to shocks and do not expose them to
water.
138
Download from Www.Somanuals.com. All Manuals Search And Download.
❍ Moving a memory card rapidly between hot and cold temperatures may cause
condensation to form on its external and internal surfaces. If condensation forms on
the card, put it aside until the droplets have evaporated completely.
❍ Do not touch or expose the terminals to dust or dirt.
❍ Check the direction before inserting the memory card. Forcing a memory card
backwards into the slot may damage the memory card or the camcorder.
❍ Do not remove the label from the memory card, or affix other labels on the memory
card.
E
Using the Camcorder Abroad
Power Sources
You can use the compact power adapter to operate the camcorder and to charge
battery packs in any country with power supply between 100 and 240 V AC, 50/60 Hz.
Consult the Canon Service Center for information on plug adapters for overseas use.
Playback on a TV Screen
You can only play back your recordings on TVs with NTSC system. The NTSC system is
used in the following countries/areas:
American Samoa, Antigua, Aruba, Bahamas, Barbados, Bermuda, Bolivia, Canada,
Chile, Columbia, Costa Rica, Cuba, Ecuador, El Salvador, Guam, Guatemala, Greenland,
Haiti, Honduras, Jamaica, Japan, Korea, Mexico, Micronesia, Myanmar, Nicaragua,
Panama, Peru, Philippines, Puerto Rico, Saint Kitts and Nevis, Saint Lucia, Saint Vincent
and the Grenadines, Surinam, Taiwan, Trinidad and Tobago, USA, Venezuela, Virgin
Islands.
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have a problem with your camcorder, refer to this checklist. Consult your dealer
or a Canon Service Center if the problem persists.
Power Source
Problem
Cause
Solution
Camcorder will not turn Battery pack is exhausted.
on.
Replace or charge the
battery pack.
13
13
13
25
13
16
13
–
Battery pack is not correctly Attach the battery pack
attached.
correctly.
The camcorder switches Battery pack is exhausted.
off by itself.
Replace or charge the
battery pack.
Power save function has
been activated.
Turn on the camcorder.
Cassette compartment
will not open.
Battery pack is exhausted.
Replace or charge the
battery pack.
Cassette compartment cover Open the cassette
is not fully open.
compartment cover fully.
Cassette compartment
stopped during loading/
unloading.
Battery pack is exhausted.
Replace or charge the
battery pack.
The camcorder
malfunctions.
Consult a Canon Service
Center.
LCD/viewfinder switches Battery pack is exhausted.
on and off.
Replace or charge the
battery pack.
13
Recording/Playback
24
16
16
13
Buttons will not work.
Camcorder is not turned on. Turn on the camcorder.
Cassette is not loaded.
v flashes on the screen. Cassette is not loaded.
Load a cassette.
Load a cassette.
k flashes on the
screen.
Battery pack is exhausted.
Replace or charge the
battery pack.
138
16
h flashes on the screen. Condensation is detected.
See reference page.
“Remove the cassette”
appears on the screen.
Camcorder stopped
operating to protect the
tape.
Unload and reload the
cassette.
77
20
The wireless controller
will not work.
Camcorder and wireless
controller are not set to the modes.
same remote sensor mode.
Change the remote sensor
Batteries of the wireless
controller are exhausted.
Replace the batteries.
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording
Problem
Cause
Solution
Image will not appear
on the screen.
Camcorder is not set to
CAMERA mode.
Set the camcorder to
CAMERA mode.
24
21
E
“Set the time zone, date Time zone, date and time
and time” appears on
the screen.
Set the time zone, date and
time, or replace the backup
battery and reset the date
and time.
are not set, or the backup
battery is exhausted.
Pressing the start/stop
button will not start
recording.
Camcorder is turned off.
Cassette is not loaded.
Turn on the power.
Load a cassette.
24
16
16
Tape reached the end (bEND Rewind the tape or replace
flashes on the screen).
the cassette.
Cassette is protected (v
flashes on the screen).
Replace the tape or change 138
the position of the protect
switch.
Camcorder is set to a mode
Set the camcorder to
24
52
18
other than the CAMERA mode. CAMERA mode.
Camcorder will not
focus.
Autofocus does not work on Focus manually.
that subject.
Viewfinder is not adjusted.
Adjust the viewfinder with
the dioptric adjustment
lever.
Lens is dirty.
Clean the lens.
134
–
A vertical light bar
appears on the screen.
Bright light in a dark scene
may cause a vertical light
bar (smear) to appear. This is
not a malfunction.
– – –
Sound is distorted or
recorded in a lower
volume than the actual
volume.
When recording near loud
sound (such as fireworks,
drums or concerts), sound
may become distorted or
may not be recorded in the
actual sound level. This is
not a malfunction.
–
– – –
Viewfinder picture is
blurred.
Viewfinder is not adjusted.
Adjust the viewfinder with
the dioptric adjustment
lever.
18
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
33
Pressing the playback
button does not start
playback.
Camcorder is turned off, or is Set the camcorder to PLAY
not set to PLAY (VCR) mode. (VCR) mode.
16
33
Cassette is not loaded.
Load a cassette.
Rewind the tape.
Tape reached the end (
flashes on the screen).
36
85
36
Image will not appear
on the TV screen.
[AV/PHONESH] is set to
[PHONESH] in the menu.
Set [AV/PHONESH] to [AV] in
the menu.
[AV \DV OUT] is set to
[ON].
Set [AV \DV OUT] to [OFF].
Tape is running, but
image will not appear
on the TV screen.
TV/VIDEO selector on the TV Set the selector to VIDEO.
is not set to VIDEO.
135
–
Video heads are dirty.
Clean the video heads.
You attempted to play back Stop playback/dubbing.
or dub copyright protected
tape.
35
92
No sound from the built- Speaker volume is turned
Adjust the volume with the
SET dial.
in speaker.
off.
Memory Card Operation
Problem
Cause
Solution
Memory card cannot be Memory card was not facing Turn the memory card over
inserted. the correct direction. and reinsert it.
Memory card cannot be Memory card is full.
recorded.
Replace the memory card or 92
erase images.
Memory card is not
formatted.
Format the memory card.
117
Memory card is not inserted. Insert a memory card.
92
95
File number reached
maximum value.
Set [FILE NUMBERS] to
[RESET] and insert a new
memory card.
SD Memory Card is
protected.
Change the position of the
protect switch.
92
Memory card cannot be Camcorder is not set to
Set the camcorder to CARD
PLAY mode.
106
played back.
CARD PLAY mode.
Memory card is not inserted. Insert a memory card.
92
109
92
Image cannot be erased. Image is protected.
Cancel the protection.
SD memory card is
protected.
Change the position of the
protect switch.
flashes red.
Card error occurred.
Turn off the camcorder.
Remove and reinsert the
memory card. Format the
memory card if flashing
persists.
117
142
Download from Www.Somanuals.com. All Manuals Search And Download.
(Availability differs from area to area)
System Diagram
E
CG-580 Battery Charger
WS-20 Wrist Strap
WA-30.5 Wide
Attachment
BP-500 Series Battery Pack
CB-570
CG-570
Battery Charger
SS-900 Shoulder Strap
Car Battery Cable
WD-30.5/
WD-H30.5
MiniDV
Video Cassette
Wide-converter
CA-570 Compact
Power Adapter
WL-D82 Wireless
Controller
TL-30.5/
TL-H30.5
Tele-converter
CA-570 Compact
Power Adapter
FS-30.5U
Filter Set
BP-500 Series
Battery Pack
S-150 S-video Cable
TV
BP-900 Series
Battery Pack
STV-250N
Stereo Video Cable
VL-10Li
Battery
VCR
Video Light
Commercially available
DV Cable
Digital Device
PC Card Adapter
SDC-128M
SD Memory Card
SC-1000 Soft
Carrying Case
USB Reader/Writer
MultiMediaCard
Computer
IFC-300PCU
USB Cable
SC-2000 Soft
Carrying Case
SC-A50 Soft
Carrying Case
Bubble Jet Direct compatible printers/
PictBridge-compliant printers
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Call or visit your local retailer/dealer for genuine Canon video accessories. You can also
obtain genuine accessories for your Canon camcorder by calling: 1-800-828-4040,
Canon U.S.A. Information Center.
Use of genuine Canon accessories is recommended.
This product is designed to perform optimally when used with genuine Canon
accessories. Canon shall not be liable for any damage to this product and/or
accidents such as fire, etc., caused by the malfunction of non-genuine Canon
accessories (e.g., a leakage and/or explosion of a battery pack). Please note that this
warranty does not apply to repairs arising out of the malfunction of non-genuine
Canon accessories, although you may request such repairs on a chargeable basis.
BP-500 Series Battery Packs
When you need extra battery packs, select from the
following: BP-511, BP-512, BP-514, BP-522 or BP-535.
CG-580 Battery Charger
Use the battery charger for charging BP-500 series battery
packs. It plugs directly into a power outlet without a cable.
CG-570 Battery Charger
The battery charger can be used with the supplied CA-570
Compact Power Adapter or the optional CB-570 Car Battery
Cable to charge BP-500 series battery packs.
Battery Pack
Charging Time
CG-580
60 min.
80 min.
90 min.
150 min.
210 min.
CG-570
55 min.
95 min.
95 min.
140 min.
205 min.
BP-508 (Supplied)
BP-512/BP-511 (Optional)
BP-514 (Optional)
BP-522 (Optional)
BP-535 (Optional)
* Charging time varies according to the charging condition.
CB-570 Car Battery Cable
Use the car battery cable with the CG-570 Battery Charger to
charge battery packs on the move. The car battery cable plugs
into your car’s cigarette lighter and runs off a 12-24 V DC
negative ground battery
144
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-30.5/TL-H30.5 Tele-converter
This Tele-converter lens increases the focal
length of the camcorder lens by a factor of 1.9
(TL-30.5) or 1.7 (TL-H30.5).
• The image stabilizer is not as effective when
the Tele-converter is attached.
E
• The minimum focusing distance with the TL-30.5 is 13.1 ft. (4 m); 1.6 in. (4 cm) at
maximum wide angle. With the TL-H30.5, it is 9.8 ft (3 m); 1.2 in. (3 cm) at maximum
wide angle.
• When the Tele-converter is attached, a shadow may appear in the picture when you
record with video light (ZR90: or assist lamp).
WD-30.5/WD-H30.5 Wide-converter
This lens decreases focal length by a factor of
0.7, giving you a wide perspective for indoor
shots or panoramic views.
• When the Wide-converter is attached, a
shadow may appear in the picture when you
record with video light (ZR90: or assist lamp).
FS-30.5U Filter Set
Neutral density and MC protector filters help
you to control difficult lighting conditions.
VL-10Li Battery Video Light
This compact yet powerful video light can be
used for both indoor and outdoor shooting. It
attaches to the camcorder’s accessory shoe and
is powered by BP-900 series battery packs.
• Approximate usage time: BP-915: 60 min., BP-
930: 120 min., BP-945: 170 min.
• BP-900 series battery packs are charged with the CA-920 Compact Power Adapter or
CH-910 Dual Battery Charger/Holder.
WS-20 Wrist Strap
Use this for extra additional protection for
active shooting.
145
Download from Www.Somanuals.com. All Manuals Search And Download.
SC-1000/SC-2000 Soft Carrying Case
A handy camcorder bag with padded
compartments and plenty of space for
accessories.
SC-A50 Soft Carrying Case
This lightweight bag keeps the camcorder
within easy reach without weighing you down
or getting in the way.
E
N
O
N
This mark identifies genuine Canon video accessories. When you
use Canon video equipment, we recommend Canon-brand
accessories or products bearing the same mark.
U
N
IN
A
C
E
Y
I
D
E
R
O S
O
S
A
C
E
Provided Accessories
Lens Cap
D52-0220-000
8468A002AA
D85-1360-000
CA-570 Compact Power Adapter
BP-508 Battery Pack
STV-250N Stereo Video Cable
SS-900 Shoulder Strap
WL-D82 Wireless Controller
IFC-300PCU USB Cable
WA-30.5 Wide Attachment
3067A002AA (D82-0590-201)
D81-1470-000
D83-0672-000
6906A001AA
D55-0170-000
Optional Accessories
BP-511 Battery Pack
BP-512 Battery Pack
3055A002AA (D85-1112-201)
6760A002AA
BP-514 Battery Pack
9366A002AA
BP-522 Battery Pack
BP-535 Battery Pack
3174A002AA (D85-1122-201)
6741A002AA
S-150 S-Video Cable
3062A002AA (D82-0330-202)
6740A002AA
9064A001AA
6739A002AA
9065A001AA
TL-30.5 Tele-converter
TL-H30.5 Tele-converter
WD-30.5 Wide-converter
WD-H30.5 Wide-converter
FS-30.5U Filter Set
6738A002AA
WS-20 Wrist Strap
3118A002AA (D81-0190-202)
9389A001AA
3083A002AA (D81-1200-201)
D81-1302-201
3140A002AA (D86-0081-201)
3141A002AA (D86-0090-201)
3134A002AA (D36-0032-201)
SC-2000 Soft Carrying Case
SC-1000 Soft Carrying Case
SC-A50 Soft Carrying Case
VL-10Li Battery Video Light
JR 7.2V 10WF Halogen Bulb
DVM-CL DV Cleaning Cassette
146
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
ZR90/ZR85/ZR80
System
E
Video Recording System
2 rotary heads, helical scanning DV system (consumer digital VCR
SD system), digital component recording
Audio Recording System
Television System
Image Sensor
PCM digital sound: 16 bit (48 kHz/2 ch); 12 bit (32 kHz/4 ch)
EIA standard (525 lines, 60 fields) NTSC color signal
1/6-inch CCD, approx. 680,000 pixels
Effective pixels: tape approx. 340,000 pixels
card approx. 447,000 pixels (ZR90/ZR85)
Tape Format
Tape Speed
Videocassettes bearing the “MiniDV” mark.
SP: 0.74 ips (18.81 mm/s), LP: 0.49 ips (12.56 mm/s)
SP: 80 min., LP: 120 min.
Maximum Recording Time
(80 min. cassette)
Fast Forward/Rewind Time
LCD Screen
Approx. 2 min. 20 sec. (with a 60 min. cassette)
2.5-inch. TFT color, approx. 112,000 pixels
0.33-inch. TFT color, approx. 113,000 pixels
Stereo electret condenser microphone
ZR90: f=2.8-61.6 mm, F=1.6-3.6, 22x power zoom
ZR85: f=2.8-56 mm, F=1.6-3.2, 20x power zoom
ZR80: f=2.8-50.4 mm, F=1.6-2.9, 18x power zoom
11 elements in 8 groups
Viewfinder
Microphone
Lens
Lens Configuration
Filter Diameter
30.5 mm
AF system
TTL autofocus, manual focusing possible
3.3 ft. (1 m); 0.39 in. (1 cm) on maximum wide angle
Minimum Focusing Distance
White Balance
Auto white balance, pre-set white balance (indoor, outdoor) or
custom white balance
Minimum Illumination
Recommended Illumination
Image Stabilization
2 lx (using the Night mode)
More than 100 lx
Electronic
Memory Card (ZR90/ZR85)
Recording media
SD Memory Card, MultiMediaCard
Number of Recording Pixels
Still image: 1024 × 768, 640 × 480 pixels
Movie: 320 × 240, 160 × 120 pixels, 15 frames/sec.
File Format
Design rule for Camera File system (DCF), Exif 2.2* compliant,
DPOF compliant (still images only)
*This camcorder supports Exif 2.2 (also called “Exif Print”). Exif Print is a standard for enhancing
the communication between camcorders and printers. By connecting to an Exif Print-compliant
printer, the camcorder’s image data at the time of shooting is used and optimized, yielding
extremely high quality prints.
Image Recording Format
Still image: JPEG (compression: Super Fine, Fine, Normal)
Movie: AVI (image data: Motion JPEG; audio data: WAVE
(monaural))
147
Download from Www.Somanuals.com. All Manuals Search And Download.
Input/Output Terminals
AV Terminal
ø3.5 mm minijack
Video:
1 Vp-p/75 ohms unbalanced
-10 dBV (47 kohm load)/3 kohms or less
-10 dBV/40 kohms or more
Audio output:
Audio input:
DV Terminal
Special 4-pin connector (IEEE 1394 compliant)
ø3.5 mm stereo mini-jack
Headphone Terminal
USB Terminal (ZR90/ZR85)
S-video Terminal (ZR90)
mini-B
1 Vp-p/75 ohms (Y signal), 0.286 Vp-p/75 ohms (C signal)
Power/Others
Power supply (rated)
7.4 V DC
Power consumption (AF on)
Operating temperature
Dimensions (W × H × D)
Weight (camcorder body only)
2.3W (using viewfinder), 3.3W (using LCD screen)
32 – 104 ˚F (0 – 40 ˚C)
2.1 × 3.7 × 5.5 in. (53× 95 × 139 mm) excluding protrusions
1.1 lb. (485 g)
CA-570 Compact Power Adapter
Power supply
Power consumption
Rated output
100 – 240 V AC, 50/60 Hz
17W
8.4 V DC, 1.5 A
Operating temperature
Dimensions
32 – 104 ˚F (0 – 40 ˚C)
2.1 × 3.5 × 1.1 in. (52 × 90 × 29 mm)
4.8 oz. (135 g)
Weight
BP-508 Battery Pack
Battery type
Rechargeable Lithium Ion Battery
7.4 V DC
Rated voltage
Operating temperature
Battery capacity
Dimensions
32 – 104 ˚F (0 – 40 ˚C)
800 mAh
1.5 × 0.83 × 2.2 in. (38 × 21 × 55 mm)
2.3 oz. (65 g)
Weight
SDC-8M SD Memory Card
Capacity
8 MB
Interface
SD Memory Card standard
32 – 104 ˚F (0 – 40 ˚C)
1.3 × 0.94 × 0.08 in. (32 × 24 × 2.1 mm)
0.07 oz. (2 g)
Operating temperature
Dimensions
Weight
Weight and dimensions are approximate. Errors and omissions excepted. Subject to
change without notice.
148
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
12bit audio . . . . . . . . . . . . . . . . . . 89
16:9 widescreen . . . . . . . . . . . . . . 78
6-second auto date . . . . . . . . . . . . 71
DV dubbing. . . . . . . . . . . . . . . . . . 83
DV terminal. . . . . . . . . . . . . . . 80, 91
E
E
Easy recording. . . . . . . . . . . . . . . . 46
Effects . . . . . . . . . . . . . . . . . . . . . . 64
End search. . . . . . . . . . . . . . . . . . . 72
Erasing still images . . . . . . . . . . . 110
A
Abroad, using the camcorder . . . 139
Accessories. . . . . . . . . . . . . . . . 8, 144
AE shift . . . . . . . . . . . . . . . . . . . . . 51
Analog line-in . . . . . . . . . . . . . . . . 82
Analog-digital converter. . . . . . . . 84
Assist lamp . . . . . . . . . . . . . . . . . . 49
Audio dubbing . . . . . . . . . . . . . . . 88
Audio mode . . . . . . . . . . . . . . . . . 60
Auto . . . . . . . . . . . . . . . . . . . . . . . 46
Autofocus . . . . . . . . . . . . . . . . . . . 52
AV insert . . . . . . . . . . . . . . . . . . . . 86
AV -> DV . . . . . . . . . . . . . . . . . . . . 84
AV/headphones terminal . . . . 35, 36
F
Faders . . . . . . . . . . . . . . . . . . . . . . 62
Fast forward . . . . . . . . . . . . . . . . . 34
File numbers . . . . . . . . . . . . . . . . . 95
Focusing . . . . . . . . . . . . . . . . . . . . 52
Focusing point. . . . . . . . . . . . . . . 103
Focus-Priority. . . . . . . . . . . . . . . . 103
Formatting . . . . . . . . . . . . . . . . . 117
G
Grip belt . . . . . . . . . . . . . . . . . . . . 18
B
Backup battery . . . . . . . . . . . . . . . 17
Battery charger . . . . . . . . . . . . . . 144
Battery pack . . . . . . . . . . . . . . . . . 13
Beep . . . . . . . . . . . . . . . . . . . . . . . 78
Brightness . . . . . . . . . . . . . . . . . . . 26
H
Headphones . . . . . . . . . . . . . . 35, 61
I
Image quality . . . . . . . . . . . . . . . . 93
Image stabilizer. . . . . . . . . . . . . . . 79
Index screen . . . . . . . . . . . . . . . . 107
C
Card jump . . . . . . . . . . . . . . . . . . 108
Card mix . . . . . . . . . . . . . . . . . . . 111
Computer . . . . . . . . . . . . . . . 91, 118
Condensation . . . . . . . . . . . . . . . 136
Connections - TV. . . . . . . . . . . . . . 36
Connections - VCR. . . . . . . . . . . . . 36
Copying still images . . . . . . . . . . 115
Copyright signals. . . . . . . . . . . . . . 83
L
Language . . . . . . . . . . . . . . . . . . . 76
LCD mirror mode . . . . . . . . . . . . . 25
LCD screen. . . . . . . . . . . . . . . . . . . 24
Lens cap . . . . . . . . . . . . . . . . . . . . 18
Low light mode. . . . . . . . . . . . . . . 46
LP mode . . . . . . . . . . . . . . . . . . . . 59
D
Data code . . . . . . . . . . . . . . . . . . . 70
Date and time. . . . . . . . . . . . . . . . 21
Date format . . . . . . . . . . . . . . . . . 76
Date search . . . . . . . . . . . . . . . . . . 74
Demo mode . . . . . . . . . . . . . . . . . 79
Digital effects . . . . . . . . . . . . . . . . 62
Digital zoom . . . . . . . . . . . . . . . . . 31
Direct print function . . . . . . . . . . 120
M
Maintenance . . . . . . . . . . . . . . . . 134
Manual focus . . . . . . . . . . . . . . . . 52
Memory card. . . . . . . . . . . . . . . . . 92
Menus . . . . . . . . . . . . . . . . . . . 39-45
Movie size . . . . . . . . . . . . . . . . . . . 94
MultiMediaCard . . . . . . . . . . . . . . 92
Multi-image screen . . . . . . . . . . . . 64
149
Download from Www.Somanuals.com. All Manuals Search And Download.
My Camera settings . . . . . . . . . . . 75
Speaker . . . . . . . . . . . . . . . . . . . . . 35
Sports mode . . . . . . . . . . . . . . . . . 46
Spotlight mode . . . . . . . . . . . . . . . 46
Still image quality . . . . . . . . . . . . . 93
Still image size . . . . . . . . . . . . . . . 93
Stitch Assist mode . . . . . . . . . . . . 104
Super Night mode. . . . . . . . . . . . . 49
N
Night mode. . . . . . . . . . . . . . . . . . 49
Night+ mode. . . . . . . . . . . . . . . . . 49
O
Operating Mode . . . . . . . . . . . . . . . 5
Output channel. . . . . . . . . . . . . . . 38
T
Tape protection. . . . . . . . . . . . . . 138
Time code . . . . . . . . . . . . . . . . . . . 27
Time zone . . . . . . . . . . . . . . . . . . . 21
Tripod . . . . . . . . . . . . . . . . . . . . . . 32
Troubleshooting . . . . . . . . . . . . . 140
TV Screen. . . . . . . . . . . . . . . . 36, 128
P
Photo search . . . . . . . . . . . . . . . . . 74
Playback - Memory card . . . . . . . 106
Playback - Tape . . . . . . . . . . . . . . . 33
Playback pause . . . . . . . . . . . . . . . 34
Portrait mode . . . . . . . . . . . . . . . . 46
Power adapter . . . . . . . . . . . . . . . 13
Print order. . . . . . . . . . . . . . . . . . 126
Program AE. . . . . . . . . . . . . . . . . . 46
Protect. . . . . . . . . . . . . . . . . . . . . 109
U
USB terminal . . . . . . . . . . . . 118, 120
V
Video heads. . . . . . . . . . . . . . . . . 135
Video light . . . . . . . . . . . . . . . . . 145
Videocassettes. . . . . . . . . . . . . . . . 16
Viewfinder . . . . . . . . . . . . . . . . . . 18
R
Record review . . . . . . . . . . . . . . . . 28
Record search . . . . . . . . . . . . . . . . 28
Recording movies (memory card) 101
Recording movies (tape) . . . . . . . . 24
Recording programs . . . . . . . . . . . 46
Recording still images
W
White balance. . . . . . . . . . . . . . . . 54
Wide attachment . . . . . . . . . . . . . 19
Widescreen . . . . . . . . . . . . . . . . . . 78
Wind screen . . . . . . . . . . . . . . . . . 60
Wireless controller . . . . . . . . . . . . 20
(memory card). . . . . . . . . . . . . . . 96
Recording still images (tape) . . . . 29
Remote sensor. . . . . . . . . . . . . . . . 77
Review. . . . . . . . . . . . . . . . . . . . . 100
Rewind . . . . . . . . . . . . . . . . . . . . . 33
Z
Zero set memory. . . . . . . . . . . . . . 73
Zooming . . . . . . . . . . . . . . . . . . . . 30
S
S1 video terminal . . . . . . . . . . . . . 37
Sample images . . . . . . . . . . . . . . 113
Sand & Snow mode. . . . . . . . . . . . 46
Screen displays . . . . . . . . . . . . . . 129
SD Memory Card. . . . . . . . . . . . . . 92
Search select . . . . . . . . . . . . . . . . . 74
Self-timer . . . . . . . . . . . . . . . . . . . 58
Shoulder strap. . . . . . . . . . . . . . . . 19
Shutter speed . . . . . . . . . . . . . . . . 56
Skin detail . . . . . . . . . . . . . . . . . . . 50
Slide show . . . . . . . . . . . . . . . . . . 107
SP mode . . . . . . . . . . . . . . . . . . . . 59
150
Download from Www.Somanuals.com. All Manuals Search And Download.
U.S.A.
CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY FOR
THE UNITED STATES
E
The warranty set forward below is given by Canon U.S.A., Inc. with respect to equipment purchased in the
United States. The limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase.
Canon consumer digital video equipment is warranted under normal, non-commercial, personal use, against defective
materials or workmanship as follows:
Parts:
Defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the
date of original purchase, except for a defective Video Head, which will be exchanged for a period of three months from
the date of purchase.
Labor:
For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by our factory
service centers or designated service facilities located in the United States.
When returning equipment under this warranty, you must pre-pay the shipping charges, and you must enclose the Bill of
Sale or other proof of purchase with a complete explanation of the problem. During your ONE-YEAR warranty period,
repairs will be made and the equipment return-shipped to you free of charge. After your warranty period is over, you will
be given an estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is
incurred. If you approve, repairs will be made and the equipment return-shipped to you. (shipping charges apply). If you
disapprove, we will return-ship the equipment at no charge to you.
Non-Canon brand peripheral equipment and software which may be distributed with Canon DV camcorders are
sold “AS IS” without warranty of any kind by CUSA, including any implied warranty regarding merchantability
or fitness for a particular purpose. The sole warranty with respect to such non-Canon brand items is given by
the manufacturer or producer thereof.
CUSA shall have no responsibility under this limited warranty for use of Canon DV Camcorders in conjunction with
incompatible peripheral equipment and incompatible software.
In order to obtain warranty service, contact the authorized Canon retail dealer from whom you purchased the DV
Camcorder or call the CANON INFORMATION CENTER AT 1-800-828-4040). You will be directed to the nearest service
facility for your product.
This Limited Warranty covers all defects encountered in normal use of the equipment and does not apply in the following
cases:
A) Loss or damage to the equipment due to abuse, mishandling, accident, improper maintenance, or failure to
follow operating instructions;
B) If the equipment is defective as a result of leaking batteries, sand, dirt or water damage;
C) If defects or damages are caused by the use of unauthorized parts or by service other than our authorized
agent;
D) If the equipment is used for commercial or industrial use.
This Limited Warranty does not cover cabinet (exterior finish), video cassette tape, head cleanings, nor does it apply to
equipment purchased outside the United States. This warranty does not cover units sold to rental firms, military operations,
hotels, schools, hospitals or for other commercial, industrial, or institutional applications. These uses are covered only by
such specific warranty as Canon may issue with such sales.
This Limited Warranty does not apply to accessories or consumables for the DV Camcorder, which are sold “AS IS”, without
warranty of any kind by CUSA.
Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This card is most important in
order to be sure you are contacted right away should there be a safety inspection, modification or product recall under
applicable laws or regulations.
NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THIS
EQUIPMENT AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY, EXCEPT AS MENTIONED ABOVE,
GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS EQUIPMENT SHALL BIND THE UNDERSIGNED.
(SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU). CUSA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE
FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OF DATA, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE DV CAMCORDER, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CUSA HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CUSA BE GREATER THAN THE PURCHASE PRICE OF THE
DV CAMCORDER SOLD BY CUSA AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU
ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTYAND TO OTHERS AND
THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE DV CAMCORDER NOT CAUSED DIRECTLY BY
THE NEGLIGENCE OF CUSA. (SOME STATES DO NOT ALLOW THE EXCLUSIN OR LIMITATION OF INCEDENTIAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).THIS WARRANTY SHALL NOT EXTEND
TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS EQUIPMENT OR THE PERSON FOR WHOM IT WAS
PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CANON U.S.A., INC.
151
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADA
CANON CONSUMER DIGITAL VIDEO EQUIPMENT LIMITED WARRANTY
The limited warranty set forth below is given by Canon Canada Inc. (“Canon Canada”) with respect to Canon digital video
equipment purchased in Canada. This limited warranty is only effective upon presentation of a bill of sale or other proof of
purchase for this Canon digital video equipment to a Canon Service Facility when repairs are required.
Canon consumer video digital equipment is warranted under normal, non-commercial, personal use, against defective
materials or workmanship as follows:
Parts: Defective parts will be exchanged for new parts or, at Canon Canada’s option, comparable rebuilt parts for a period
of one year from the date of original purchase, except Video Heads which will be exchanged for a period of 3 months from
the date of purchase.
Labour:
For a period of one year from the date of original purchase, labour will be provided free of charge by our
Canon Service Facilities in Canada.
This limited warranty covers all defects except where:
(a) The loss or damage to the product results from:
i) accident, natural disaster, mishandling, abuse, neglect, unauthorized product modification or failure to follow
instructions contained in the instruction manual;
ii) the use of accessories, attachments, products, supplies, parts or devices with this Canon product that do not
conform to Canon specifications or that cause abnormally frequent service problems;
iii) repairs or services performed by any party other than a Canon Service Facility;
iv) defective batteries or any exposure to water, sand or dirt;
v) shipping (claim must be presented to the shipper);
(b) Any serial number on the video equipment is altered or removed.
(c) The digital video equipment is used for commercial, professional or industrial purposes.
This limited warranty does not cover the cabinet (exterior finish) of the digital video equipment, video cassette tapes, head
cleanings, nor does it apply to digital video equipment purchased outside Canada.
TO OBTAIN WARRANTY SERVICE
Ship your Canon digital video equipment in its original carton, box or equivalent, properly packed, fully insured with
shipping charges prepaid, together with a copy of your bill of sale or other proof of purchase and a description of the
problem to any of the Canon Service Facilities in Canada.
LIMITATIONS
Except as otherwise required by applicable legislation, this warranty is in lieu of all other warranties, conditions, guarantees
or representations, express or implied, statutory or otherwise, relative to this Canon product, including implied warranties
or conditions of merchantability or fitness for a particular purpose.
Canon Canada assumes no liability for special, consequential or incidental damages or loss that may arise, whether on
account of negligence or otherwise, from the use, misuse or inability to use this Canon product (including loss of profit,
revenue, video tapes or enjoyment) or from failure to conform to any express or implied warranties, conditions, guarantees
or representations. Any recovery under this limited warranty shall not exceed the purchase price of the product. Canon
Canada does not assume or authorize any other person to assume for Canon Canada any other liability with respect to this
Canon product.
This warranty does not extend to any person other than the original purchaser of this Canon product or the person for
whom it was purchased as a gift and states your exclusive remedy.
NOTICE TO CONSUMER
If you plan to take important videos or if the product has not been used for some time, please check all functions with the
instruction book before using it.
152
Download from Www.Somanuals.com. All Manuals Search And Download.
CANON INC.
U.S.A.
CANON U.S.A., INC. NEW JERSEY OFFICE
100 Jamesburg Road, Jamesburg, NJ 08831 USA
CANON U.S.A., INC. CHICAGO OFFICE
100 Park Blvd., Itasca, IL 60143 USA
CANON U.S.A., INC. LOS ANGELES OFFICE
15955 Alton Parkway, Irvine, CA 92618 USA
CANON U.S.A., INC. HONOLULU OFFICE
210 Ward Avenue, Suite 200, Honolulu, HI 96814 USA
● If you have any questions, call the Canon U.S.A. Information
Center toll-free at 1-800-828-4040 (U.S.A. only).
CANADA
CANON CANADA INC. NATIONAL HEADQUARTERS
6390 Dixie Road, Mississauga, Ontario L5T 1P7
CANON CANADA INC. CALGARY
2828, 16th Street, N.E. Calgary, Alberta T2E 7K7
CANON CANADA INC. MONTREAL
5990 Côte de Liesse, Quebec H4T 1V7
● If you have any questions, call the Canon Canada Information
Center toll-free at 1-800-828-4040. (Canada only)
● Si vous avez des questions, veuillez téléphoner sans frais au
Canada 1-800-828-4040. (Canada seulement)
MEXICO
CANON MEXICANA, S. DE R.L. DE C.V.
Periferico Sur No. 4124 Col. Ex-Rancho de Anzaldo C.P. 01900
México, D.F., México
CENTRAL Y
SURAMÉRICA
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, FL 33126 USA
ASIA
CANON HONGKONG COMPANY LTD.
19/F, The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong
Printed on 100% reused paper.
Document réalisé avec du papier recyclé à 100%.
El papel aqui utilizado es 100% reciclado.
PRINTED IN JAPAN
IMPRIME AU JAPON
IMPRESO EN JAPÓN
PUB.DIM-618
0000Ni0.0
© CANON INC. 2004
DY8-9120-411-000
Download from Www.Somanuals.com. All Manuals Search And Download.
|
