PROFESSIONAL 1000
TRADITIONAL 1000
Use and Installation Instructions
This appliance must be installed in accordance with the regulations in force and
only used in a well ventilated space.
The data badge is fitted on the rear panel. The model/serial number can also be found
on a badge located below the left-hand oven door beneath the door seal.
Read these instructions before installing or using the appliance and retain them for
future reference.
Part No. 195050411.00
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
To help you make the best use of your cooker, PLEASE READ THIS BOOKLET
CAREFULLY.
Your new cooker is guaranteed and will give lasting service. The guarantee is only
applicable if the cooker has been installed in accordance with the Installation
Instructions.
The cooker is designed specifically for domestic use and responsibility will not be
accepted for use in any other installation.
When first using the cooker ensure that the room is well ventilated (e.g. open a
window or use an extractor fan) and that persons who may be sensitive to the odour
avoid any fumes. It is suggested that any pets be removed from the room until the
smell has ceased. This odour is due to any temporary finish and also any moisture
absorbed by the insulation.
Our policy is one of continual improvement in design and development,
therefore strict accuracy of illustrations and descriptions cannot be
guaranteed.
This appliance conforms to the following EEC Directive:
Gas Appliances
90/396/EEC
Low Voltage Equipment
73/23/EEC
93/68/EEC
Electromagnetic Compatibility
89/336/EEC
92/31/EEC
93/68/EEC
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
Please read the precautions below before using your cooker.
ALWAYS . . .
ALWAYS make sure you understand the controls before using the cooker.
ALWAYS check that all controls on the cooker are turned off after use.
ALWAYS stand back when opening an oven door to allow heat to disperse.
ALWAYS use dry, good quality oven gloves when removing items from the ovens.
ALWAYS take care when removing items from the grill when the main oven is on, as
the contents may be hot.
ALWAYS keep the oven and grill doors closed when the cooker is not in use.
ALWAYS place pans centrally over the hotplate burners and position them so that
the handles cannot accidentally be caught or knocked or become heated
by other burners.
ALWAYS keep the cooker clean, as a build up of grease or fat from cooking can
cause a fire.
ALWAYS allow the cooker to cool before cleaning.
ALWAYS follow the basic principles of food handling and hygiene to prevent the
possibility of bacterial growth.
ALWAYS keep ventilation slots clear of obstructions.
ALWAYS turn off the electricity supply before cleaning or replacing the oven lamp.
ALWAYS refer servicing to CORGI registered appliance service engineers.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
NEVER . . .
NEVER leave children unsupervised where the cooker is installed as all surfaces will
get hot during and after use.
NEVER allow anyone to sit or stand on any part of the cooker.
NEVER store items that children may attempt to reach above the cooker.
NEVER heat up unopened food containers as pressure can build up causing the
container to burst.
NEVER store chemicals, food stuffs, pressurised containers in or on the cooker, or in
cabinets immediately above or next to the cooker.
NEVER fill a deep fat frying pan more than 1/3 full of oil, and never use a lid.
DO NOT LEAVE UNATTENDED WHILE COOKING.
NEVER place flammable or plastic items on or near the hotplate.
NEVER use proprietary spillage collectors on the hotplate.
NEVER use the cooker as a room heater.
NEVER dry clothes or place other times over or near to the hotplate or oven/ grill
doors.
NEVER wear garments with long flowing sleeves whilst cooking.
NEVER operate the grill with the grill doors closed. This may cause overheating of
your cooker.
NEVER line the shelves, floor or sides of the oven or grill with aluminium foil as over
heating and damage can result.
NEVER use steam cleaners.
NEVER touch the heating elements inside the oven or grill even when off.
NOTE: The use of a gas cooking appliance results in the production of heat and
moisture in the room in which it is installed. Always ensure that the kitchen is well
ventilated; keep natural ventilation holes open or install a mechanical ventilation device
(mechanical extractor hood).
In particular, when using more than one hotplate burner, open a window if a
mechanical ventilation device is not operating.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN TIMER OPERATION
The oven timer offers you the following features:
1. Time of Day
2. Automatic Cooking
3. Minute Minder
AUTOMATIC COOKING
The fanned oven can be controlled automatically.
GUIDANCE ON AUTOMATIC COOKING
1. Select foods which will take the same time to cook.
2. Set the oven timer so that the food has just finished or is just about to finish
cooking on your return to the oven. This will ensure the food has not cooled
down and does not require reheating before serving.
3. Food should be as cold as possible when it goes into the oven, ideally
straight from the refrigerator. Frozen meat and poultry should be thawed
thoroughly before it is put in the oven.
4. Warm food should never be placed in the oven if there is to be a
delay period. Stews prepared by frying the meat and vegetables should be
cooked as soon as possible.
5. Dishes containing left-over cooked poultry or meat, for example
Shepherds Pie, should not be cooked automatically if there is to be a delay
period.
6. Stews and joints should be cooked by the long slow method, so that the delay
period is kept to a minimum.
7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry,
joints, etc) the delayed start should be kept to a minimum.
8. Wine or beer may ferment and cream may curdle during the delay period, so it
is best to add these ingredients just before serving.
9. Foods which discolour should be protected by coating in fat or tossing in water
to which lemon juice has been added, prior to placing food in the oven.
10. Dishes containing liquid should not be filled too full to prevent boiling over.
11. Food should be well sealed (but not airtight) in a container to prevent the loss
of liquid during cooking. Aluminium foil gives a good seal.
12. Ensure food is cooked thoroughly before serving.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN TIMER OPERATION
CLOCKFACE
The timer incorporates a 24 hour clock.
Ensure the correct time of day is always set, before using your cooker.
SYMBOLS
A ‘bell’ symbol will light up when you select a Minute Minder Period and will
remain lit for the period set.
At the end of the Minute Minder Period, the timer will emit an audible tone and
the ‘bell’ symbol will disappear.
The ‘cookpot’ symbol will light up either:–
–
–
When the timer is in manual mode, or
During the actual Cook Period.
‘AUTO’ will light up:–
–
When the timer is first turned on it will flash. It will go out when a time of day
is set or when the timer is set to manual.
The ‘AUTO’ symbol will flash at the end of an Auto Cooking programme to indi-
cate that the programme has finished.
(When the ‘AUTO’ symbol is flashing, to return the oven to Manual operation,
turn the oven controls off, ensure that the correct time of day is set, and press
the “Manual” button – The ‘AUTO’ symbol will go out).
TIMER FUNCTION BUTTONS
Minute Minder
Button
Here you can set a time period of up to 23 hours 59 minutes, that will count down.
When it reaches zero, the timer will emit an audible tone.
For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.
AUTO COOKING PROGRAMME
Cook Period Button Cook Period is the actual length of time for which, the timer will switch the oven(s)
on as part of an “Auto Cooking” programme.
(e.g. If you set 2 hours, the food will be cooked for 2 hours).
End Time Button
The time of day at which you want an “Auto Cooking” programme to end.
For Example: If you set a “Cook Period” for 2 hours, and “End Time” of 11:00. The
timer will switch the oven(s) on at 9:00 and turn the oven(s) off at 11:00. You will hear
a audible tone at 11:00, to indicate that the Auto Cooking Programme has finished.
Notes:
-
When setting an Auto Cooking programme you will need to set the oven
control(s) to the required temperature(s) when you set the timer.
If an Auto Cooking programme has been set the oven(s) will only operate during
the pre-programmed time.
-
Manual Button
Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to
Manual operation.
“+” and “–” Buttons Used to adjust the various timer function settings.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN TIMER OPERATION
SETTING THE TIME OF DAY
Step 1 Make sure all oven controls are turned Off.
Step 2 Check the electricity supply to the cooker is turned on.
Step 3 When switched on the display will show 0.00 and the Auto symbol,
flashing intermittently.
Step 4 Press & hold in both the Cook Period & End Time buttons together.
Step 5 With the Cook Period & End Time buttons still held in, press either the “+”
or “–” buttons to set the correct time of day.
Step 6 Release all the buttons simultaneously.
THE TIME OF DAY IS NOW SET.
To change the time of day repeat Steps 4, 5 & 6 above.
Note: You cannot adjust the time of day if the timer has been set for an
Auto Cooking Programme.
SETTING THE MINUTE MINDER
Step 1 Ensure the time of day is set correctly.
Step 2 Press and hold the Minute Minder button.
Step 3 With the Minute Minder button held in, set the required Minute Minder
period using the “+” and “–” buttons. A ‘bell’ symbol will light up.
Release all buttons and the timer display will revert back to the time of day.
The ‘bell’ symbol will remain lit to signify that a Minute Minder period has been
set.
At the end of the set time an audible tone will be heard, and the ‘bell’ symbol will
disappear.
Step 4 To cancel the audible tone press the Minute Minder button.
Note 1 When the Minute Minder has been set, the time remaining can be checked at any
time by simply pressing the Minute Minder button.
Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by
pressing and holding the Minute Minder button and then at the same time
pressing the “–” button until 0.00 appears in the display window.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN TIMER OPERATION
AUTO COOKING PROGRAMMES
There are two Auto Cooking programmes that can be selected using your timer:–
(a) To set the timer to switch the oven(s) On and Off Automatically
(b) To set timer to switch on immediately and OFF automatically after a set cook period.
a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY
This allows you to cook at a specified time for a chosen period before the oven switches
off Automatically.
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Press and hold in the Cook Period button.
The display will read 0.00 with the ‘cookpot’ symbol lit.
Step 4 With the Cook Period button still held in, set the required Cook Period
using the “+” and “–” buttons.
Release the buttons and the timer display will revert to the time of day with the
‘Auto’ symbol and ‘cookpot’ symbol lit.
Step 5 Press and hold in the End Time button.
The display will read the earliest possible end time for the Cook Period
that you have set above.
The ‘Auto’ symbol and ‘cookpot’ symbol will be lit.
Step 6 With the End Time button still held in, use the “+” and “–” buttons to set
the ‘End Time’ (i.e. The time you require the oven to switch off).
Release all the buttons and the timer will revert back to the time of day.
The ‘Auto’ symbol will remain lit to signify that an Auto Cooking Programme has
been set. The ‘cookpot’ symbol will go out.
Step 7 Turn the oven control(s) to the required temperature, and if necessary
select the appropriate oven function.
At the end of the Automatic Cook Period the Auto Symbol will flash and an
intermittent bleeping sound will be heard.
The audible tone will continue unless cancelled.
The ‘Auto’ symbol will continue to flash until the timer is returned to Manual
operation (see below).
Step 8 Press the Manual button, the audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN TIMER OPERATION
Note 1 When cooking automatically the Cook Period can be checked at any time by simply
pressing the Cook Period button.
Note 2 When cooking automatically the End Time can be checked at any time by simply
pressing the End Time button.
b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET COOK
PERIOD
Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.
Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).
Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven
function.
Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the
‘cookpot’ symbol will light up.
With the Cook Period button still held in set the required Cook Period using the
“+” and “–” buttons. Example: 1hr 30 minutes (as shown).
Note: Cook Period is the length of time the food requires to cook.
Step 5 Release all buttons.
The timer display will revert to the time of day with the ‘Auto’ symbol lit &
‘cookpot‘ symbol remaining lit.
At the end of the Cook Period the ‘Auto’ symbol will flash and an intermittent
audible tone will be heard.
NOTE: The Cookpot symbol disappears
The audible tone will continue until cancelled. The ‘Auto’ symbol will continue to
flash until the timer is returned to Manual operation (see below).
Step 6 Press the Manual button. The audible tone will be cancelled and the
oven(s) will be returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OVEN TIMER OPERATION
TO CANCEL AN AUTO COOKING PROGRAMME BEFORE
THE COOK PERIOD HAS FINISHED.
Step 1 Turn the oven control(s) to the OFF position.
Step 2 Press the Manual button to return the oven(s) to “Manual” operation.
The ‘Auto’ symbol will go out.
Note 1
When cooking automatically the Cook Period can be checked at any time by simply pressing
the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook
Period button.
2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time
button.
3. Having set a Cook Period and End Time an electronic device stores the information. The device within the
timer will switch the oven(s) on and off at the required times.
4. When setting an Auto Cooking Programme and a mistake is made, to clear:–
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero’s 0.00 and ‘Auto’, it is likely that the electricity supply to
the oven has been interrupted. Reset the timer to the correct time of day.
Food in the oven may, therefore, not have been cooked, before serving check food is thoroughly heated
and completely cooked.
6. To set each function always press and hold the required function button and at the same time press “+” or
“–” buttons.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOTPLATE
The hotplate has one dual control wok burner, one large high speed burner, three
normal simmering burners and one small simmering burner. The dual control wok
burner consists of a smaller inner and a larger outer burner that can operate either
together or separately. Use of the two burners together with large pans on maximum
setting gives a very high input and reduces cooking times with respect to
conventional burners. Use of the two burners together provides a more uniform
distribution of heat on the bottom of the pan. Cookware of all sizes can be used above
the dual control wok burner. For small pans it is recommended that only the inner
burner is used.
❍
❍
❍
❍
❍
❍
The knob situated below the symbol
The knob situated below the symbol
on the fascia panel operates the outer burner.
on the fascia panel operates the inner burner.
❍
❍
❍
❍
❍
ꢀ
TO USE THE HOTPLATE
1. Press the ignition button and then push in and turn the control knob of the
chosen burner anti-clockwise to the large flame symbol. Continue to press
the ignition button until the spark lights the gas. When operating the dual
control burner there is a separate control knob for the inner and outer
burners.
2. Turn the control knob anti-clockwise to the desired setting.
Only turn the control knob between the large flame symbol and the small
flame symbol for adjusting the setting.
3. To turn off, turn the control knob fully clockwise to the O position.
DO NOT use mis-shapen pans which may be unstable.
DO NOT use round base woks directly on the pan supports.
Each burner is fitted with a spark ignition electrode for lighting the gas.
To ensure rapid lighting of the burners every time they are used, the electrodes must be
kept clean and dry. Remove any food spillage or cleaning materials from the electrodes
using a small nylon brush such as a tooth brush.
Access to the ignitor can be achieved by lifting off the loose burner parts carefully when
the burners are cool.
If aluminium based pans are used, a silvery deposit may appear on the top edge of the
pan support fingers. See ‘Care and Cleaning’ section for further information.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOTPLATE
SAFETY REQUIREMENTS FOR DEEP FAT FRYING
1. Never fill chip pans more than one third full with oil or fat.
2. Never leave oil or fat unattended during the heating or cooling period.
3. Never heat fat or fry with a lid on the pan.
4. Always dry food thoroughly before frying, and lower it slowly into the hot oil
or fat. Frozen foods in particular will cause frothing and spitting if added too
quickly.
5. Always keep the outside of the pan clean and free from streaks of oil or fat.
HOW TO DEAL WITH A FAT FIRE
1. Do not move the pan.
2. Turn off the hotplate burners.
3. Smother the flames with a fire blanket or damp cloth to extinguish the fire.
Do not use water or a fire extinguisher as the force of it may spread the
burning fat or oil over the edge of the pan.
4. Leave the pan for at least 60 minutes before moving it.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TWIN GRILL
CAUTION – ACCESSIBLE PARTS MAY BECOME HOT WHEN THE GRILL IS IN USE.
YOUNG CHILDREN SHOULD BE KEPT AWAY.
GRILLING SHOULD NEVER BE UNDERTAKEN WITH THE GRILL DOOR CLOSED.
The grill control is designed to provide variable heat control of either the full width of
the grill or just the grill half. Turning the control knob clockwise will switch on the full
width and turning anticlockwise will switch on just the grill half.
A gentle flow of air will be blown from underneath the control panel when the grill is
in use.
If the fan fails to blow air beneath the control panel when the grill is in use, you
should contact your service engineer immediately (see Key Contacts, back page).
GRILL PAN HANDLE
The grill pan handle is detachable from the pan to facilitate cleaning. The handle can
be either detachable from or fixed to the pan.
Remove the screw and washer from the grill pan bracket, tilt the handle over the
recess adjacent to the bracket (A). Slide the handle towards the centre of the pan (B)
and let the handle locate over the bracket (C).
For a detachable handle: Remove the screw and washer from the grill pan and keep
safe.
For a fixed handle: Replace the screw and washer and ensure they are fully tightened.
Warning: Ensure when using grill pan handle in the detachable manner it is
centralised and secure.
TO USE THE GRILL
1. Open the grill door.
2. Turn the grill control knob clockwise to 4 for full width grilling or anticlockwise for
half width grilling.
3. Slide the grill pan toward the back of the grill compartment until it stops.
4. Leave the control at 4 for toast and for sealing and for fast cooking of foods. For
thicker foods requiring longer cooking, turn the control to a lower setting after
sealing on both sides at 4.
Grilling can be started from cold but for best results preheat for approximately 2
minutes.
DO NOT cover the grill pan or grid with aluminium foil as this can hold fat,
intensify the heat and create a fire hazard.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FAN OVEN
The heating of the oven is achieved by turning the control knob clockwise to the
required temperature as recommended in the temperature charts. The pilot light will
immediately come on and will automatically go off and on during cooking as the oven
thermostat maintains the correct temperature.
It should be noted that at the end of a cooking period there may be a momentary puff
of steam when the oven door is opened, this will disperse in a few seconds and is a
perfectly normal characteristic of an oven with a good seal.
Since a fan oven heats up more quickly and generally cooks food at a lower temperature
than a conventional oven, pre-heating the oven is often unnecessary. However, foods
such as bread, scones, Yorkshire pudding do often benefit from being placed in a pre-
heated oven.
The charts on pages 20 and 21 are a guide only, giving approximate cooking tempera-
tures and times. To suit personal taste and requirements, it may be necessary to increase
or decrease temperatures by 10˚C.
Unless otherwise indicated in the charts, food is placed in a cold oven ie. without pre-
heating. If food is placed in an already hot oven, the suggested cooking time should be
reduced, depending on the type and quantity of food being cooked.
OVEN POSITIONS
Since the distribution of heat in the fan oven is very even, most foods will cook satisfac-
torily on any shelf position, but the shelves should be evenly spaced.
To ensure even circulation do not use meat pans larger than 390 x 300mm (15ins x 12ins)
and baking trays no larger than 330 x 255mm (13ins x 10ins), these should be positioned
centrally on the oven shelf.
-
-
-
Do not fit shelves upside down.
Never use more than 3 shelves in the oven as air circulation will be restricted.
Food or cooking utensils should not be placed on the floor of the oven.
To avoid unnecessary cleaning, rod shelves which are not in use should be removed
from the oven.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FAN OVEN
TEMPERATURE AND TIME
When all three shelves are used to cook large quantities of food for home freezing or
parties, it may be necessary to increase the cooking times given in the charts by a few
minutes to allow for the loss of heat due to the extra time taken to load the oven, and
the larger mass of food. Baking trays should allow an equal gap on all sides of the
oven.
NB. Recipes in cookery books give times and temperatures for cooking in ordinary
ovens. The fan oven makes it possible in most cases to:
-
-
-
Reduce the recommended temperatures 25˚C (45˚F).
Reduce the recommended time by approximately 10 minutes per hour.
Make pre-heating the oven unnecessary for certain foods.
TO PREPARE MEAT AND POULTRY FOR ROASTING IN YOUR FAN OVEN
a. Wipe the meat or poultry, dry well and weigh it. Meat which has been stored in a
refrigerator should be allowed to come to room temperature before cooking and
frozen meat or poultry must be completely defrosted before placing in the oven.
b. The weight of any stuffing used should be added before calculating the cooking
time.
c. Place meat / poultry in the main oven meat pan supplied with your cooker. Small
joints weighing less than 1.75kg (31/2lb) should be roasted in a smaller meat pan
/ tin - or they may be ‘pot roasted’ - a small joint in a large meat pan causes
unnecessary oven splashing and evaporation of meat juices.
d. Additional fat should not be added, except for veal, very lean meat or poultry
which can be ‘larded’ with bacon fat or brushed very sparingly with cooking oil
or melted fat.
e. Beef, lamb, mutton and poultry may be dusted lightly with seasoned flour to give
a crisp outer surface. The skin of duck and goose should be pricked to release
excess fat during cooking and the rind of pork should be scored, brushed lightly
with oil and rubbed with salt to give crisp crackling.
f.
Meat and poultry wrapped in, or covered with a tent of aluminium foil will be
juicy and tender. Roasting bags offer the same advantage. Always follow the
manufacturer’s packing instructions and remember to reduce the temperatures
given for conventional ovens by approximately 25˚C and the time by approxi
mately 10 minutes per hour.
g. Potatoes for roasting only require to be brushed with cooking oil or melted fat.
h. It is not necessary to baste when roasting in an electric oven and stock or liquid
should not be added to the meat pan since this only causes unnecessary soiling,
steam and condensation.
FROZEN MEAT AND POULTRY
Joints of meat and whole birds should be defrosted slowly, preferably in a domestic
refrigerator (allowing 5-6 hours per 450g, 1lb), or at room temperature (allowing 2-3
hours per 450g, 1lb). Frozen meat or poultry must be completely defrosted before
placing in the oven. It is essential to wash thoroughly and cook meat and poultry
immediately after defrosting.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVENTIONAL OVEN
OVEN CONTROL
Heating of the oven is achieved by turning the control clockwise to the required oven tempera-
ture scale on the control panel, as recommended in the temperature charts. The pilot light will
immediately come on and off during cooking as the thermostat maintains the correct tempera-
ture.
The charts on pages 20 and 21 are a guide only, giving approximate cooking temperatures and
times. To suit personal taste and requirements, it may be necessary to increase and decrease
temperatures by 10˚C.
The oven is fitted with ‘heat clean’ liners and two rod shelves. The heating of the oven is
achieved by turning the control knob clockwise to the required temperature as recommended
in the temperature charts. The pilot light will immediately come on and will automatically go off
and on during cooking as the oven thermostat maintains the correct temperature.
It should be noted that at the end of a cooking period there may be a momentary puff of steam
when the oven door is opened. This will disperse in a few seconds and is a perfectly normal
characteristic of an oven with a good seal.
The correct positioning of food is indicated on the temperature charts.
TO PREPARE MEAT FOR ROASTING IN YOUR CONVENTIONAL OVEN
Wipe the joint, dry well with a clean cloth, kitchen tissue etc. and weigh it. Meat which has been
stored in a refrigerator should be allowed to come to room temperature for approximately 30
minutes before cooking and frozen meat or poultry must be completely defrosted beforehand.
Beef, lamb, mutton and poultry may be lightly floured, but pork should be scored, brushed
lightly with oil and rubbed with salt to give crisp crackling. Place joint in the main oven meat
pan supplied with your cooker. (Small joints weighing less than 1.75kg (31/2lb) should be
roasted in a smaller meat pan / tin - or they may be ‘pot roasted’ - a small joint in a large meat
pan causes unnecessary oven splashing and evaporation of meat juices). Additional fat should
not be added, except for veal, very lean meat or poultry which can be ‘larded’ with bacon fat or
brushed very sparingly with cooking oil or melted fat. It is not necessary to baste, when roast-
ing in an electric oven and liquid / stock should not be added to the pan.
For optimum cooking performance, there must be clearance between meat pan and oven sides.
The meat pan must be placed lengthways in the oven to allow for air circulation.
TIMES AND TEMPERATURES FOR ROASTING
The secret of succulent, tender meat, is not to roast it too quickly at too high a temperature.
Best results are obtained when roasting is carried out at a low temperature. When a lower tem-
perature is used, the joint loses less weight, is more tender (too high a temperature causes meat
to be tough and dry) and the splashing of fat onto oven interior is reduced to a minimum.
When a complete meal is being cooked in the oven, cooking time may need to be increased and
temperature may need to be raised for approximately the last 30 minutes of the cooking period
(for instance when cooking Yorkshire pudding to serve with roast beef). The suggested times
and temperatures given below should be used as a guide, but may vary according to:-
1. Whether you prefer meat rare, medium or well done.
2. The size and shape of your joint.
(a)
(b)
A short thick joint requires a longer cooking period than a long thin joint.
A small joint under 1.5kg (3lbs) takes longer per 450g (1lb) cook in the time given for
‘minutes’ per 450g (1lb) without the ‘minutes’ over added.
Boned/rolled and stuffed joints take longer to cook through than those with a bone.
The weight of stuffing should be added to the oven ready weight of the meat /
poultry to calculate roasting times.
(c)
NOTE:
Remember to switch off the oven control after cooking is finished. If the door of the
oven is left open for long periods of time with the control switch ON, then the grill
element will become hot. The correct positioning of food is indicated in the
temperature charts.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If soft margarine is used for cake making, temperatures recommended by the
manufacturers should be followed. Temperatures recommended in this chart refer to cakes
made with block margarine or butter only.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
THE ‘SLOW COOK’ SETTING
With the fanned oven thermostat set to 90˚ the oven can be used for slow cooking - The
‘Slow Cook’ setting.
PREPARING FOOD FOR SLOW COOKING
1. All dishes cooked by the ‘Slow Cook’ setting should be cooked for a minimum 6
hours. They will ‘hold’ at this setting for a further hour but marked deterioration in
appearance will be noticed in some cases.
2. Joints of meat and poultry should be cooked at 170˚ for 30 minutes before
turning to the ‘Slow Cook’ setting and never be cooked lower than the middle shelf
position.
3. Joints of meat over 6 lbs (2.7kg) and poultry over 4 lbs 8oz (2 kg) should not
be cooked using the ‘Slow Cook’ setting.
4. Always stand covered joints on a rack over the meat tin to allow good air
circulation.
5. A meat thermometer should be used when cooking pork joints and poultry.
The internal temperature of the food should reach at least 88˚C.
6. This method is unsuitable for stuffed meat and stuffed poultry.
7. Always bring soups, casseroles and liquids to the boil before putting in the
oven.
8. Cover casseroles with foil and then the lid to prevent loss of moisture.
9. Always thaw frozen food completely before cooking.
10. Root vegetables will cook better if cut into small pieces.
11. Adjust seasonings and thickenings at the end of the cooking time.
12. Use the zones of heat in the oven, e.g. meringues and milk puddings can be
cooked lower in the oven whilst other dishes requiring greater heat can be
cooked above them.
13. Egg and fish dishes need only 1-5 hours cooking and should be included in
day cooking sessions, when they can be observed from time to time.
14. Dried red kidney beans must be boiled for a minimum of ten minutes after
soaking, before inclusion in any dish.
STORAGE COMPARTMENT
Take care as accessible surfaces inside the storage compartment will become hot
when the oven is in use. The storage compartment is ideal for storing saucepans meat
pans, etc.
Do not use it for storing combustible materials, flammable liquids or aerosols.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
WARNING: NEVER USE STEAM CLEANERS.
Switch off the electricity supply and allow to cool before cleaning the cooker.
Clean the cooker regularly and wipe up spills soon after they occur to prevent
them from becoming burnt on. Never use biological washing powder, caustic
cleaners, harsh abrasives, scouring pads, steam cleaners, aerosol cleaners or oven
chemical cleaners of any kind.
Before moving your cooker ensure that it is cool and note that it is heavy so you
may require assistance. The cooker is fitted with rear wheels and will slide in and out
of position easily. Movement of your cooker is most easily achieved as follows:
Open the grill/oven door sufficiently to allow a comfortable grip on the underside
front edge of the oven roof, avoiding contact with any grill or oven furniture and then
lift and slide at the same time.
When repositioning the cooker, ensure that it is level. Take care to ensure that any floor
covering is not damaged.
‘HEAT CLEAN’ LINERS
The oven linings are coated with a special enamel which has a continuous cleaning
action. The higher the oven temperature the more effective the action. In most cases
this cleaning operation will proceed during normal cooking.
However, if high temperatures are not used regularly it may be necessary to run the
oven empty at maximum setting for one hour. If desired, they can be wiped over with
a soapy cloth followed by a wipe with a clean, damp cloth.
REPLACEMENT OF OVEN LIGHT BULB
CAUTION: DISCONNECT THE APPLIANCE FROM THE ELECTRICITY SUPPLY BEFORE
REPLACING THE LAMP TO AVOID THE POSSIBILITY OF AN ELECTRIC SHOCK
Light bulbs are not covered by the manufacturer’s guarantee.
A new 15W, 300˚C rated SES bulb can be obtained from your cooker supplier or any
major electrical retailer.
1. Remove the shelves from the oven.
2. Unscrew the lens using a thick cloth to protect your fingers in the unlikely
event of a lens fracture.
3. Unscrew bulb.
4. Fit new bulb and refit lens.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
COOKER FINISH
Vitreous Enamel
Hotplate (Traditional), pan
supports, burner caps,
roasting dish, grill pan, oven
base, rear and roof, door
inner panels, grill and
storage compartment.
CLEANING METHOD
Cloth wrung out in warm soapy water. Stubborn
stains can be removed with a cream paste,
liquid cleaner or by rubbing with fine steel wool
soap pads e.g. Brillo, Ajax.
Check that the cleaning agent is approved by the
Vitreous Enamel Association.
Similar to paint cleaning above. Use a nylon brush to
remove any cleaning materials, water or dirt from
the hotplate burner ports. Care should be taken
when refitting the bodies over the electrodes.
Aluminium
Burner bodies, door handles.
Glass
As for enamel cleaning. Polish with a clean dry cloth
or kitchen roll.
Chromium Plating
Oven shelves, grill pan grid,
grill pan handle support
Wipe with a cloth wrung out in warm soapy water.
A fine steel wool soap pad e.g. Brillo, Ajax, or a
chrome or stainless steel cleaner may be used.
Wipe with a cloth wrung out in warm soapy water.
Plastic
Grill pan handle, control
knobs, door handle supports.
Stainless Steel (Professional)
Door trims, control panel,
hotplate.
Wipe with a cloth wrung out in warm soapy water.
Polish with a clean dry cloth or kitchen towel. For
stubborn stains, use a proprietary stainless steel
cleaner and follow the instructions on the container.
Paint
Wipe with a cloth wrung out in warm soapy water
Control panel and doors
(Traditional), side panels
only.
DO NOT USE ABRASIVES.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SOMETHING WRONG
WITH YOUR COOKER
Before contacting your Service Centre or Installer, check the problem guide
below, there may be nothing wrong with your cooker.
PROBLEM
CHECK
Slight odour or small
amount of smoke when
grill/oven used for first
time.
This is normal and should cease after a short period.
Check that the oven setting and shelf positions are as
recommended in the Cooking Charts.
Oven cooks too fast or too
slow.
However, it may be necessary to increase or decrease
the recommended setting slightly to suit your taste.
Ignition does not work.
If all burners fail to ignite:
Check that sparks appear at the burners; a clicking
noise should be heard.
If not
(i)
Check that the electricity supply is turned on.
(ii) Check other appliances to see if you have had a
power cut.
If only one burner fails to ignite:
(i)
Check the burner cap is seated correctly.
(ii) Check the slots in the burner bodies are not
blocked with any soap residue or cooking soil
(see care and cleaning).
(iii) Check, if the burners have recently been
cleaned using a wire wool pad eg. “Brillo Pad’,
ensure that no stray strands are caught on the
ignitor or burner body.
NOTE. Satisfactory ignition will only be achieved if all
the hotplate burners are fitted.
In the event of an electricity failure, all burners can be
lit with a match.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SOMETHING WRONG
WITH YOUR COOKER
CHECK
PROBLEM
Cannot set an ‘Auto Cook’
programme or cannot get
the Timer to turn the oven
on or off at the required
times.
Read the Timer instructions in this book carefully
remembering that the Cook period is the length of
time that the timer will switch the oven(s) on as part
of an Auto Cooking Programme.
The electricity supply to the cooker may have been
interrupted, but has now come back on again. Set
the correct time of day by following the instructions
given in the Timer section of this book.
Timer display shows ‘0:00’
with ‘AUTO’ flashing.
The Timer may be set for an Auto Cooking
programme. Check the Timer to see if “AUTO” is
illuminated. If it is, follow the instructions given in
the Timer section of this book to cancel the Auto
Cooking programme.
Fanned oven does not work,
but the grill, top oven and
hotplate burners work.
The oven lamp is not covered by the guarantee. The
part is easily changed (see the section on oven lamp
replacement). A new lamp may be obtained from
our Parts Department (see Key Contacts, back page).
Oven lamp does not work.
If there is still a problem contact your local Service office
(see KEY CONTACTS, back page).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Prior to installation, ensure that the local distribution conditions (nature of the gas and
gas pressure) and the adjustment conditions are compatible. The adjustment
conditions for this appliance are stated on the data badge which is fitted on the rear
panel.
This appliance is not designed to be connected to a combustion products evacuation
device. It must be installed and connected in accordance with current installation
regulations. particular attention should be given to the relevant requirements
regarding ventilation.
MODEL NUMBERS 10850G, 10855G, 10856G
Category II2H3+ (GB. IE)
This model is set to burn NATURAL GAS (G20) at 20 mbar but can be converted for use
on BUTANE (G30) at 28-30mbar or PROPANE (G31) at 37mbar with the use of a service
kit supplied with the appliance or available from our Service and Genuine Parts and
Accessories department (see KEY CONTACTS, back cover).
GAS SAFETY (INSTALLATION & USE) REGULATIONS
It is the law that all gas appliances are installed by competent persons in
accordance with the current edition of the above regulations. It is in your interest and
that of safety to ensure compliance with the law.
In the UK, CORGI registered installers work to safe standards of practice.
The cooker must also be installed in accordance with BS 6172.
Failure to install the cooker correctly could invalidate the warranty liability claims and
could lead to prosecution.
LOCATION
The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in
a room containing a bath or shower. The cooker must not be installed in a bed-sitting
room of less than 20m3.
When adjusted for use on BUTANE (G30) or PROPANE (G31) the cooker must not be
installed in a room or internal space below ground level, eg. in a basement.
PROVISION FOR VENTILATION
The room containing the cooker should have an air supply in accordance with
BS 5440: Part 2.
The room must have an opening window or equivalent; some rooms may also require
a permanent vent. If the room has a volume between 5 and 10m3, it will require an air
vent of 50cm2 effective area unless it has a door which opens directly to outside. If the
room has a volume of less than 5m3, it will require an air vent of 100cm2 effective area.
If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be
consulted to determine air vent requirements.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
TECHNICAL DATA
DIMENSIONS
Height
900 - 915mm
Width
1000mm
Depth
600mm (excluding door handles)
GENERAL
Gas connection
1
1
2
2
Rp / ( / ” BSP female)
Hotplate burner injector
None
Pressure test point
Gas rate adjustment
Aeration adjustment
Electrical connection
Total electrical heat input
None
230/240V a.c. 50Hz.
7.2 kW
Cat II2H3+
G30 at 28 - 30 mbar
G31 at 37 mbar
Cat II2H3+
G20 at 20 mbar
240V a.c.
HEAT
INPUT
HEAT
INPUT
INJECTOR
GAS RATE
INJECTOR
HEAT INPUT
BURNER
HOTPLATE
Front Left
102
128
1.80 kW
130g/hr
205g/hr
2.0 kW
3.0 kW
65
82
HOTPLATE
Rear Left
2.80 kW
4.75 kW
HOTPLATE
Wok Inner
Centre Front
44
2 x 70
50
70
2 x 114
72
5.10 kW
345g/hr
HOTPLATE
Wok Outer
Centre Front
HOTPLATE
Auxiliary
1.00 kW
75g/hr
1.02 kW
Centre Rear
HOTPLATE
Front Right
102
102
1.8 kW
1.8 kW
130g/hr
130g/hr
2.0 kW
2.0 kW
65
65
HOTPLATE
Rear Right
2.66 kW
2.50 kW
2.00 kW
0.22 kW
TWIN GRILL
L/H OVEN
R/H OVEN
WARMING
DRAWER
26
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
CONVERSION FOR USE ON BUTANE OR PROPANE
Each hob burner requires the injector to be replaced and each burner gas tap to have
the by-pass screw adjusted according to the following procedure:
1. Lift off the burner cap and the burner body and place it to one side.
2. Remove the injector from the burner base with a suitable box spanner and
discard.
3. Replace the injector with the appropriate replacement (see Table on page 28).
4. Repeat for each burner.
5. Replace the burner bodies and caps, taking care that they are positioned
correctly.
6. Remove the tap knob from the left hand hotplate tap. Insert a narrow flat
screwdriver centre of the tap spindle and turn fully clockwise. Replace the tap
knob. Repeat this procedure with the other six hotplate taps.
7. Position and fix the self-adhesive LPG conversion label over the gas details on the
rating plate label.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
SPACE FOR FIXING
The cooker can be close fitted below hotplate level. This requires a minimum
distance of 1000mm between cupboard units of hotplate height.
When installing next to a tall cupboard, partition or wall, for a minimum distance of
400mm above hotplate level, allow a side clearance of at least 65mm.
The diagram below illustrates the minimum clearance between the cooker and
adjacent walls, cupboards etc.
The wall behind the cooker between the hotplate and 450mm above, and the width of
the cooker, must be a non-combustible material such as ceramic wall tiles.
If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a
clearance to adjacent base cabinets of at least 50mm to allow the main oven door to
open fully for removing oven shelves.
COOKER HOODS
If a cooker hood is to be installed, refer to the cooker hood manufacturers’ instructions
regarding fixing height.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
UNPACKING
Unpack the components from inside the grill and ovens: Check that the following parts
are present.
Meat pan
Pan supports (3)
LPG conversion kit
Oven shelves (4)
Literature pack
Grill pan, grid and handle
Loose burner parts (14)
Aluminium burner bodies (6)
After unpacking your cooker, make sure that you remove all the packing from the oven
and grill, and any stickers from the oven door and the hob.
LEVELLING
Your cooker is heavy, so it would be advisable for two people to move it. The cooker is
fitted with rear wheels and will slide into position easily. Movement of your cooker is
most easily achieved as follows. Open the grill/oven door sufficiently to allow a com-
fortable grip on the underside front edge of the oven roof, avoiding any grill or oven
interior furniture, and then lift and slide back at the same time.
Your cooker must stand on a flat surface so that the hob is perfectly level, and the
cooker is stable and cannot be rocked, this is easily achieved by adjusting the three
feet which are under the front of the cooker and the 3 castors under the rear of the
cooker, if necessary.
STABILITY CHAIN
The cooker must be fitted with a stability device firmly secured to the fabric of the build-
ing. The M6 bolt at the top of the rear of the cooker can be used to engage a stability
chain. Keep the chain clear of controls and pipes on the rear of the cooker.
The chain must be fitted to the wall behind the cooker.
NOTE: If the cooker is to be placed on a base, precautions must be taken to prevent it
from slipping off the base.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
The cooker is designed to match the depth of standard 600mm worktops.
An adaptor backplate should, therefore, be fitted within the shaded area shown to
allow the cooker to be pushed fully to the wall. If a forward facing backplate is used,
it must be chased into the wall.
180
450
370
Connection to the cooker should be made with an approved appliance flexible
connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose
chosen should be such that when the cooker is in situ, the hose does not touch the
floor.
The temperature rise of areas at the rear of the cooker that are likely to come in
contact with the flexible hose do not exceed 70˚C.
LPG cookers should be connected with a hose suitable for LPG and capable of
withstanding 50mbar pressure.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL CONNECTION
WARNING - THIS APPLIANCE MUST BE EARTHED
Your cooker should have been checked to ensure that the voltage corresponds with
your supply voltage, which is stated on the data badge fitted on the rear panel.
The cooker must be connected by a contractor/engineer who is registered with the
National Inspection Council for Electrical Installation Contracting (NICEIC), to a suitable
double - pole control unit with a minimum rating of 30A and a minimum contact
clearance of 3mm, which should be fitted adjacent to (but not above) the cooker, in
accordance with IEE regulations.
2
The power supply cable should conform to BS6004 with a conductor size of 4mm .
The control unit should be easily accessible in the event of an emergency.
This appliance conforms to EN55014 regarding suppression of radio and television
interference.
Access to the mains terminals is gained by removing the rear access cover.
The mains cable must pass through the cable clamp adjacent to the terminal block.
Sufficient cable should be used to allow the cooker to be pulled out for servicing.
INSTALLATION & OPERATIONAL CHECKS
After installation, check for gas soundness.
Fit the hotplate burner bodies, burner port rings, enamelled discs and pan supports
referring to the instructions for use where necessary.
1.
2.
Check that the hotplate burners ignite correctly and burn with a steady flame.
Check for a steady flame on the low setting.
Check that with the left hand oven set at 230˚C, the oven fan operates and the
oven heats up.
3.
4.
5.
Check that with the right hand oven set at 230˚C, the oven heats up.
Check that the twin grill heats up.
Check operation of clock.
Instruct the user on the operation of the cooker.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, to ensure that you can have
complete confidence in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
Republic of Ireland: 1850 302 200
Note: Our operators will require the following information:
Model number
Serial number
Extended Warranties
UK 08709 088 088
Monday to Sunday, 8am to 8pm
Republic of Ireland: 1850 502 200
Genuine Parts & Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
Republic of Ireland: (01) 842 6836
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
.
PRINTED BY: SIMLEX FOUR ASHES, WOLVERHAMPTON.
Download from Www.Somanuals.com. All Manuals Search And Download.
|