OPERATING INSTRUCTIONS
CAMPBELL
HAUSFELD
IMPACT WRENCH
MODELS TL1002, TL1017 AND TL1049
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE
PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMA-
TION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR
PROPERTY DAMAGE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Description
General Safety (Continued)
Do-It-Yourself (DIY) impact wrenches are air tools
designed for removing and installing nuts and bolts
such as lug nuts, exhaust system clamps, etc.
9. Always use attachments designed for use with air
poweredtools. Donotusedamagedorwornattach-
ments.
Unpacking
!
WARNING
!
When unpacking this product, carefully inspect for any
damage that may have occurred during transit. Make
sure any loose fittings, bolts, etc., are tightened before
putting this product into service.
DO NOT USE HAND-TOOL SOCKETS. USE IM-
PACT-QUALITY SOCKETS ONLY. HAND-TOOL
SOCKETS ARE "GLASS-HARD" AND WILL SHAT-
TER AND CAN CAUSE SERIOUS PERSONAL IN-
JURY IF USED WITH AIR TOOLS.
General Safety Information
10. Never trigger the tool when not applied to a work
object. Attachments must be securely attached.
Loose attachments can cause serious injury.
This product is a part of a high pressure system and the
following safety precautions must be followed at all
times along with any other existing safety rules.
11. Protect air lines from damage or puncture.
1. Read all manuals included with this product care-
fully. Be thoroughly familiar with the controls and
the proper use of the equipment.
12. Never point an air tool at oneself or any other
person. Serious injury could occur.
2. Only persons well acquainted with these rules of
safe operation should be allowed to use the
air tool.
13. Check air hoses for weak or worn condition before
each use. Make sure all connections are secure.
!
WARNING
!
!
!
DANGER
RELEASE ALL PRESSURE FROM THE SYSTEM
BEFORE ATTEMPTING TO INSTALL, SERVICE,
RELOCATE OR PERFORM ANY MAINTENANCE.
DO NOT EXCEED MAXIMUM OPERATING PRES-
SURE OF THE AIR TOOL (90 PSI). THE AIR TOOL
COULD EXPLODE AND RESULT IN DEATH OR
SERIOUS PERSONAL INJURY.
14. Keep all nuts, bolts and screws tight and ensure
equipment is in safe working condition.
3. Do not exceed any pressure rating of any compo-
nent in the system.
15. Do not put hands near or under moving parts.
4. Disconnect the air tool from air supply before
changing tools or attachments, servicing and dur-
ing nonoperation.
Operation
LUBRICATION
Proper lubrication is the owner's responsibility. Failure
to lubricate the air tool properly will dramatically shorten
the life of the tool and will void the warranty.
5. Always wear safety glasses during operation.
6. Do not wear loose fitting clothing, scarves, or neck
ties. Loose clothing may become caught in moving
parts and result in serious personal injury.
!
CAUTION
This impact wrench REQUIRES lubrication BE-
FORE the initial use and BEFORE and AFTER each
additional use.
7. Do not wear jewelry when operating any tool.
Jewelry
may become caught in moving parts
and result in serious personal injury.
Impact wrenches require lubrication throughout the life
of the tool and must be lubricated in two separate areas:
8. Do not depress trigger when connecting the air
supply hose.
IN230000AV 9/93
Download from Www.Somanuals.com. All Manuals Search And Download.
IN230000AV
MODELS TL1002, TL1017 AND TL1049
Operation (Continued)
FILTER
QUICK
COUPLER
(OPTIONAL)
QUICK
COUPLER
OILER
AIR SUPPLY
QUICK
CONNECTOR
LEADER
(WHIP)
HOSE
QUICK
CONNECTOR
(OPTIONAL)
REGULATOR
REGULATOR
AIR
DRAIN (WATER TRAP)
HOSE
AIR INLET (OIL HERE
DAILY IF NOT USING
AN AIR TOOL OILER)
DO NOT INSTALL A
QUICK COUPLER HERE
AIR TOOL MANUFACTURERS RECOMMEND THAT AN AIR FIL-
TER AND OILER BE USED TO INCREASE THE LIFE OF THE TOOL.
Figure 2 - Air Hose Hook-up
SPEED ADJUSTMENT
!
WARNING
!
The impact wrench should never be used to set torque.
Use a torque wrench to set the torque. Models TL1002,
TL1017 and TL1049 are equipped with regulators for
speed adjustment (See Figure 2).
NEVER CARRY A TOOL BY THE HOSE OR PULL
THE HOSE TO MOVE THE TOOL OR A COMPRES-
SOR. KEEP HOSES AWAY FROM HEAT, OIL AND
SHARP EDGES. REPLACE ANY HOSE THAT IS
DAMAGED, WEAK OR WORN.
To remove nuts, set the regulator to the maximum
setting. To install nuts, set the regulator to the minimum
to medium setting. Do not overtighten the nuts.
STORAGE
The impact wrench must be lubricated before storing.
Follow the air motor lubrication instructions with an
exception to step 4. Only run the impact wrench for 2
to3secondsinsteadof20to30secondsbecausemore
oil needs to remain in the impact wrench when storing.
AIR HOSE
Figure 2 illustrates a recommended air hose hook-up.
NOTE: It is not recommended to install a quick coupler
between the impact wrench and the leader (whip) hose
(See Figure 2).
Technical Service
Usingfittingsorairhoseswhicharetoosmallcancreate
a pressure drop and reduce the power of the tool. For
models TL1002, TL1017 and TL1049, using 3/8" (I.D.)
fittings with 1/4" NPT threads are recommended. Most
compressors are shipped with a short, 1/4" I.D. hose.
For proper performance and more convenience, use a
3/8" I.D. hose. Hoses longer than 50 feet should have a
1/2" I.D.
For information regarding the operation or repair of this
product, please call 1-800-543-6400. If you are calling
from Ohio or outside the continental United States,
please call collect, 1-513-367-1182.
Specifications & Performance
MODEL
#
AVERAGE MAX
SCFM & PSI RPM
MAX
TORQUE
AIR
INLET
EXTENDED
ANVIL
DRIVE
WEIGHT
TL1002
TL1017
TL1049
5.1 @ 90
2.4 @ 90
2.5 @ 90
7000
230 ft/lb
75 ft/lb
75 ft/lb
1/4" NPT (Female) 1/2" Sq
1/4" NPT (Female) 3/8" Sq
1/4" NPT (Female) 3/8" Sq
5 lb
2 lb
3 lb
NA
N/A
NA
10,000
10,000
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
IN230000AV
MODELS TL1002, TL1017 AND TL1049
General Troubleshooting Guide
SYMPTOM
POSSIBLE CAUSE (S)
CORRECTIVE ACTION
Tool runs slowly or will
not operate.
1. Grit or gum in tool.
1.
Flush the tool with Campbell Hausfeld air tool oil, gum
solvent, or an equal mixture of SAE 10 motor oil and
kerosene. If Campbell Hausfeld oil is not used, lubricate the
tool after cleaning.
2. No oil in tool.
2.
Lubricate the tool according to the lubrication instructions in
this manual.
3. Low air pressure.
3.a. Adjust the regulator on the tool to the maximum setting.
3.b. Adjust the compressor regulator to tool maximum while the
tool is running free.
4.
Tighten and seal hose fittings if leaks are found.
4. Air hose leaks.
5. Pressure drops.
5.a. Besurethehoseisthepropersize. Longhosesortoolsusing
large volumes of air may require a hose with an I.D. of 1/2"
or larger depending on the total length of the hose.
5.b. Do not use a multiple number of hoses connected together
with quick connect fittings. This causes additional pressure
drops and reduces the tool power. Directly connect the
hoses together.
6. Worn rotor blade in motor.
7. Worn ball bearing in motor.
6.
7.
Replace rotor blade.
Remove and inspect bearing for rust, dirt and grit or worn
race. Replace or clean and regrease bearing with bearing
grease.
Moisture blowing out
of tool
1. Water in tank.
1.
Drain tank. (See air compressor manual). Oil tool and run
until no water is evident. Oil tool again and run
1-2 seconds.
2. Water in the air lines/hoses.
2.a. Install a water separator/filter. NOTE: Separators only work
properly when the air passing through the separator is cool.
Locate the separator/filter as far as possible from the
compressor.
2. b. Install an air dryer.
2.c. Iftheoriginalseparatorwillnotseparateallthewaterfromthe
air, install a Campbell Hausfeld belt air filter (MP2121).
Impact Mechanism Troubleshooting Guide
Impacts slowly or
will not impact.
1. Lack of lubrication.
1. Lubricate the air motor and the impact mechanism. (See
Lubrication section of this manual).
2. Tool regulator set in wrong position.
2. Adjust the regulator setting of the tool.
3. Adjust regulators in the air system (See Figure 2).
3. In-line regulator or compressor regulator
set too low.
Limited Warranty
1. DURATION: One year from the date of purchase by the original purchaser.
2. WHO GIVES THIS WARRANTY (WARRANTOR):
Campbell Hausfeld
The Scott Fetzer Company
100 Production Drive
Harrison, Ohio, 45030
Telephone: (513) 367-4811.
3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product.
4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld portable air compressor, air tool or supplementary air accessory supplied or manufactured
by Warrantor.
5. WHAT IS COVERED UNDER THIS WARRANTY: Defects on material and workmanship which occur within the duration of the warranty period.
6. WHAT IS NOT COVERED UNDER THIS WARRANTY:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR FROM THE DATE OF ORIGINAL
PURCHASE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE
CAMPBELL HAUSFELD PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply
to you.
C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied
with product.
D. Pre-delivery service, i.e. assembly, oil or lubricants, and adjustment.
E. Normal adjustments which are explained in the owner’s manual(s) provided with the product, i.e. belts, pressure switch.
F. Items or service that are normally required to maintain the product, i.e. lubricants, filters and gaskets.
G. Electric motor and gasoline engine components are expressly excluded from coverage under this limited warranty. Such components should be returned by the purchaser to
the original manufacturer or to its authorized repair stations for service.
7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or components which have failed within duration of the
warranty period.
8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:
A. Deliver or ship the Campbell Hausfeld product or component to the nearest Campbell Hausfeld Authorized Service Center. Freight costs, if any, must be borne by the purchaser.
B. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY:
A. Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
B. If the purchaser does not receive satisfactory results from the Authorized Service Center, the purchaser should contact the Campbell Hausfeld Product Service Department (see
paragraph 2).
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
|