Model No. WCTL2982.0
Serial No.
USER’S MANUAL
Write the serial number in the
space above for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, please call:
1-888-936-4266
Monday through Friday from
8h00 to 17h00 EST (excluding
holidays).
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and properly tighten all parts of the
treadmill regularly.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
22. Never drop or insert any object into any
opening.
17. Never leave the treadmill unattended while it
is running. Always remove the key and
unplug the power cord when the treadmill is
not in use.
23.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 11.) You must be
able to safely lift 20 kg (45 lbs.) in order to
raise, lower, or move the treadmill.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-
erty damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on your treadmill. If a decal is missing, or
if it is not legible, please call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
!
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WESLO® CADENCE DS11 reading this manual, see the front cover of this manu-
treadmill. The CADENCE DS11 treadmill combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
you’re not exercising, the unique CADENCE DS11
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
al. To help us assist you, please note the product
model number and serial number before calling. The
model number of the treadmill is WCTL2982.0. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the
location).
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
Water Bottle Holder
(Bottle not included)
Console
Key/Clip
Handrail
Storage Latch
Upright
FRONT
Walking Belt
Foot Rails
Circuit Breaker
Power Cord
BACK
Incline Leg
RIGHT SIDE
Rear Roller
Adjustment Bolts
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a nor-
mal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply
wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrenches
and your own phillips screwdriver
, adjustable wrench , and needlenose
,
rubber mallet
pliers
, wire cutters
.
To identify small parts during assembly, use the PART IDENTIFICATION CHART in the center of this manual.
1. Make sure that the power cord is unplugged.
1
84
!
31
33
33
!
31
38
With the help of a second person, carefully tip the
treadmill onto one side. Partially fold the Frame (84) so
that the treadmill is more stable. Do not fully fold the
treadmill until it is completely assembled.
33
31
Attach four Base Pads (33) to the Base (38) with four 1”
Tek Screws (31).
2. With the help of a second person, tip the treadmill down
to the position shown.
2
15
14
53
Attach a Wheel (42) to each side of the Base (38) with a
Wheel Bolt (41) and a Wheel Nut (43) as shown.
Identify the Right Upright (15) and the Left Upright (14)
(there are two small holes in the side of the Left
Upright). While a second person holds the Right Upright
near the Wire Harness (53), insert the end of the Wire
Harness into the lower end of the Right Upright and out
of the upper end as shown. If there are plastic ties in the
lower ends of the Uprights, remove them.
Holes
38
43
42
41
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Insert a Plastic Shim (9) into each side of the post on
the right side of the Base (38). Next, hold the Right
Upright (15) so the lower end is turned as shown, and
insert it into the Base. Make sure that the Wire
Harness (53) does not fall into the top of the Right
Upright. Be careful to avoid pinching the Wire
Harness. Note: If necessary, tap the Right Upright with
a rubber mallet until it is fully seated in the Base. If the
Right Upright cannot be fully seated, remove the outer
Plastic Shim and then insert the Right Upright.
3
53
Attach the Right Upright (15) to the Base (38) with three
1” Bolts (16) and three Star Washers (2). Do not tight-
en the Bolts yet.
15
9
Orient the
Upright as
shown.
Assemble the Left Upright (not shown) in the same
way.
2
16
2
38
16
4. If there are plastic ties in the brackets on the Handrails,
remove them. Hold one of the Handrails near the Right
Upright (15) as shown. Insert the Wire Harness (53) up
through the bracket on the Handrail and out of the round
hole in the side of the Handrail. If necessary, use
4
Left Handrail
Right Handrail
53
16
needlenose pliers to pull the Wire Harness out of the
hole. Be careful not to damage the Wire Harness.
Insert the bracket into the top of the Right Uprights (15).
7
Connectors
Bracket
7
Attach the other Handrail as described above. Note:
There are no wires in the Left Upright (14).
14
16
16
7
Hand tighten four 1” Bolts (16) with Handrail Washers
(7) into the Uprights (14, 15) and the Handrails.
16
15
5. Set the Console Base (87) on the Handrails (94, 4).
Thread four 1 1/4” Tek Screws (86) into the Handrails
and the Console Base. After you have started all four
Screws, tighten the Screws until they are snug; do
not overtighten the Screws.
5
Connectors
4
53
94
Firmly tighten, but do not overtighten, the bolts
used in steps 2 through 4.
87
Plastic Ties
86
86
Insert the Wire Harness (53) through the two indicated
plastic ties on the Console Base (87) and up through the
hole in the Console Base.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Insert the Battery Cover (12) into the Console Base (87),
with the hinges in the position shown. The Battery Cover
should pivot down, away from the Console Base.
6
87
Hinges
12
7. Hold the Console (11) near the Console Base (87).
7
Touch the Right Handrail (94) to discharge any static.
11
Locate the two wires in the Wire Harness (53) that have
L-shaped connectors on the ends. Press the connectors
onto the two tabs on the switch shown in inset drawing 7a.
7a
Tabs
87
53
Connect the other two wires in the Wire Harness (53) to
the back of the Console Base (87) in the locations
shown by the arrows in drawing 7. The connectors
should slide easily into the sockets and snap into
place (see drawings 7b and 7c). If the connectors do not
slide easily and snap into place, turn the connectors and
then insert them. IF THE CONNECTORS ARE NOT
INSERTED PROPERLY, THE CONSOLE MAY BE
DAMAGED WHEN THE POWER IS TURNED ON.
7b
7c
53
Ties
94
8. Set the Console (11) in the Console Base (87). Make
sure that no wires are pinched. Insert as much of the
Wire Harness as possible (53) down the hole in the
Right Handrail (94). Securely tighten the plastic tie
nearest the Right Handrail. Pull any excess Wire
Harness between the plastic ties tight and tighten the
other plastic tie. Cut off the ends of the plastic ties.
Cover the Wire Harness with the Wire Cover (10), and
route the Wire Harness out of the hole in the side of the
Wire Cover. Attach the Wire Cover to the back of the
Console Base with two 3/4” Screws (5). Do not over-
tighten the Screws.
8
11
87
53
Ties
10
5
5
Make sure that no wires are pinched before you attach
the Console (11) to the Console Base (87). Tighten the
remaining four 3/4” Screws (5) into the Console Base and
the Console. Do not overtighten the Screws.
5
94
9. Attach the Storage Latch (66) to the left Upright (14)
with two 3/4” Screws (5).
9
14
10.Make sure that all parts used in assembly are prop-
erly tightened before you use the treadmill. Keep the
included allen wrench in a secure place. The allen
wrench is used to adjust the walking belt (see page 13).
To protect the floor or carpet, place a mat under the
treadmill.
5
66
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
grounding plug. Plug the power cord into a surge
suppressor, and plug the surge suppressor into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sili-
cone spray or other substances to the walking belt
or the walking platform. Such substances will dete-
riorate the walking belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed
by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the possi-
bility of your treadmill being damaged, always use
a surge suppressor with your treadmill (see draw-
ing 1 at the right).
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpected-
ly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should mal-
function or break down, grounding provides a path of
least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Displays
Speed Control
Note: If there is a thin sheet of clear plastic
on the face of the console, remove it before
operating the console.
removed from the console, the walking belt
will stop.
CAUTION:
Before operating the
console, read the following precautions.
• Adjust the speed in small increments.
• Do not stand on the walking belt when turning
on the power.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids on
the console. Put only sealable water bottles in
the water bottle holders.
• Always wear the clip (see the drawing below)
while using the treadmill. When the key is
BATTERY INSTALLATION
STEP-BY-STEP CONSOLE OPERATION
The console
requires two
Before operating the console, make sure that the
power cord is properly plugged in (see page 8).
12
“AA” batter-
ies (not includ-
ed). Alkaline
batteries are
recommended.
To install bat-
teries, open
the battery
Note: To prevent damage to the walking platform,
always wear clean shoes when using the treadmill.
Batteries
Step onto the
foot rails of the
12
treadmill. Find
Key
the clip attached
to the key, and
slide the clip
cover (12)
beneath the
console as
Tab
onto the waist-
band of your
shown. Press
Clip
two batteries into the console. Make sure that the
negative (–) ends of the batteries are touching the
springs. Close the battery cover, push up on the tab,
and then push the tab forward as shown in the inset
drawing. Make sure that the tab locks into place.
clothes. Next,
insert the key
fully into the con-
sole. Test the clip by carefully taking a few steps
backward until the key is pulled from the console.
If the key is not pulled from the console, adjust
the position of the clip as needed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow the steps below to operate the console.
speed of the walking belt, in miles per hour. Every
few seconds, the display will change from one
number to the next, as shown the the arrows in
the display.
Insert the key fully into the console.
1
Inserting the key will not turn on the displays. The
displays will turn on when the ON/RESET button
is pressed or when the walking belt is started.
Note: If you just installed batteries, the displays
will already be on.
To reset the displays at any time, press the
ON/RESET button.
When you are finished exercising, stop the
walking belt and remove the key.
4
Reset the speed control and start the walking
belt.
2
Step onto the foot rails, slide the speed control to
the RESET position, and remove the key from the
console. The displays will turn off a few minutes
after the key is removed. Note: Any time that
the walking belt is stopped and the ON/RESET
button is not pressed for a few minutes, the
displays will automatically turn off.
Slide the speed control
down to the RESET
position. Note: Each
time the walking belt
is stopped, the speed
control must be
moved to the RESET
position before the
walking belt can be
restarted.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are four incline lev-
els. Before changing the incline, remove the key
and unplug the power cord. Next, fold the treadmill
to the storage position (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 11).
Next, slowly slide the speed control up until the
walking belt begins to move at slow speed.
Carefully step onto the walking belt and begin
walking. Change the speed of the walking belt as
desired by sliding the speed control.
To change the incline, first remove the incline pin from
one of the incline legs as shown below. Adjust the
incline leg to the desired height and fully reinsert the
incline pin. Make sure that the incline pin is in the
“locked” position shown in the inset drawing. Adjust the
other incline leg in the same way. Make sure that both
incline pins are inserted from the direction shown.
To stop the walking belt, step onto the foot rails
and slide the speed control to the RESET position.
Note: During the first few minutes that the tread-
mill is used, inspect the alignment of the walking
belt and align it if necessary (see page 13).
Monitor your progress with the displays.
Incline
Pin
3
TIME/DISTANCE dis-
Arrow
play—This display
shows the elapsed time
and the distance that
you have walked or run,
Incline
Pin
in miles. Every few sec-
onds, the display will
Incline
Pin
change from one number to the other, as shown
by the arrows in the display.
CALS/FAT CALS/
Arrow
SPEED display—This
display shows the
approximate numbers
of calories and fat calo-
ries you have burned.
CAUTION: Before using the treadmill, make sure
that both incline legs are at the same height. Do
not use the treadmill with the incline pins
removed. After you have adjusted the incline legs,
lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 11).
(See FAT BURNING on
page 14.) In addition, the display shows the
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
in order to raise, lower or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
2
treadmill firmly. Raise the treadmill until the storage latch
closes over the catch. Make sure that the storage
latch is fully engaged over the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30º C (85° F).
Closed
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is fully engaged over the catch.
1. Hold the upper ends of the handrails. Place one foot on
one of the front wheels as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not attempt to move
the treadmill over an uneven surface.
Base
Front
Wheels
3. Place one foot on a front wheel, and carefully lower the
treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Press the stor-
age latch and hold it. Pivot the treadmill until the frame and foot rail are past the storage latch.
2. Refer to drawing 1. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not
drop the treadmill frame to the floor. CAUTION: To decrease the possibility of injury, bend your legs
and keep your back straight.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres-
sor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge sup-
pressor that meets all of the specifications described on page 8. Important: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
c
frame near the power cord. If the switch pro-
trudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console (see page 9). Most problems are the result of drained batteries.
b. Remove the key from the console and UNPLUG THE
b
POWER CORD. Remove the screws from the hood.
3mm
75
Carefully remove the hood. Locate the Reed Switch
(13) and the Magnet (63) on the left side of the Pulley
(75). Turn the Pulley until the Magnet is aligned with
the Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 3 mm
(1/8 in.). If necessary, loosen the Reed Switch Screw
(89) and move the Reed Switch slightly. Retighten the
Screw. Re-attach the hood, and run the treadmill for a
few minutes to check for a correct speed reading.
89
13
63
Top
View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may
5–7 cm
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the allen wrench, turn
both rear roller adjustment bolts counterclockwise,
1/4 of a turn. When the walking belt is properly tight-
ened, you should be able to lift each side of the walk-
ing belt 5 to 7 cm (2 to 3 in.) off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key and run the treadmill
for a few minutes. Repeat until the walking belt is
properly tightened.
Rear Roller
Adjustment Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
a
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 5 to 7 cm (2 to 3 in.) off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key and carefully walk on
the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
Aerobic Exercise
WARNING:
Before beginning
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone. It may also be helpful to set the speed control
on the console to AEROBIC to help you maintain the
proper intensity level. (See page 9.)
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
The following guidelines will help you to plan your
exercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
High Performance Athletic Conditioning
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The prop-
er intensity level can be found by using your heart rate
as a guide. The chart below shows recommended heart
rates for fat burning and aerobic exercise.
If your goal is high performance athletic conditioning,
set the speed control on the console to PERFOR-
MANCE to help you maintain the proper intensity
level. (See page 9.) Note: During the first few weeks
of your exercise program, keep your heart rate near
the low end of your training zone.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, stop exer-
cising and place two
fingers on your wrist
as shown. Take a
six-second heartbeat
count, and multiply
the result by ten to
find your heart rate.
(A six-second count is used because your heart rate
drops quickly when you stop exercising.) If your heart
rate is too high or too low, adjust the speed or incline
of the treadmill accordingly.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers at the
top of your age. The three numbers are your “training
zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
training zone. It may also be helpful to set the speed
control on the console to FAT BURN to help you main-
tain the proper intensity level. (See page 9.)
WORKOUT GUIDELINES
A well-rounded workout includes the following three
important parts:
A Warm-up
Start each workout with 5 to 10 minutes of stretching
and light exercise (see SUGGESTED STRETCHES
on page 15). A proper warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Training Zone Exercise
to cool down. This will increase the flexibility of your
muscles and will help to prevent post-exercise problems.
After warming up, increase the intensity of your exer-
cise until your pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exer-
cise program, do not keep your pulse in your training
zone for longer than 20 minutes.) Breathe regularly
and deeply as you exercise—never hold your breath.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com-
plete up to five workouts each week if desired.
A Cool-down
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
Finish each workout with 5 to 10 minutes of stretching
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees, and
back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back, and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons, and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for both legs. Stretches: Quadriceps and hip muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
• The MODEL NUMBER of the product (WCTL2982.0)
• The NAME of the product (WESLO® CADENCE DS11 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the center of this manual)
WESLO is a registered trademark of ICON IP, Inc.
LIMITED WARRANTY
ICON OF CANADA, INC., (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of one (1) year from the date of purchase.
This warranty extends only to the original purchaser. ICON’s obligation under this warranty is limited to
replacing or repairing, at ICON’s option, the product through one of its authorized service centers. All
repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center, to prod-
ucts used for commercial or rental purposes, or to products used as store display models. No other war-
ranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of
incidental or consequential damages.
Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any
and all other warranties and any implied warranties of merchantability or fitness for a particular purpose
is limited in its scope and duration to the terms set forth herein. Some provinces do not allow limitations
on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF CANADA, INC., 900 de l’Industrie, St. Jerôme, QC J7Y 4B8
Part No. 229815 R0505A
Printed in Canada © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save
this chart and the EXPLODED DRAWING/PART LIST for future reference.
3/4” Screw (5)–8
1” Tek Screw
(31)–4
1 1/4” Screw (86)–4
Star Washer (2)–6
(May be an internal
Star Washer)
1” Bolt (16)–10
Handrail Washer
(7)–4
Wheel Bolt (41)–2
Wheel Nut (43)–2
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WCTL2982.0
R0505A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
4
6
2
1
20
1
2
2
2
1
1
1
1
1
1
10
10
1
1
1
1
1
1
1
1
1
5
17
1
1
4
2
4
1
1
2
2
1
4
3
2
2
6
2
1
1
1
1
1
1
Front Endcap Screw
Star Washer
Plastic Tie
Left Handrail
3/4” Screw
Key/Clip
Handrail Washer
Incline Leg
Shim
Wire Cover
Console
Battery Cover
Reed Switch
Left Upright
Right Upright
1” Bolt
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
#
4
1
1
1
1
1
1
2
1
2
1
1
1
2
2
1
1
3
4
1
1
2
1
1
1
10
1
2
1
1
1
1
1
1
1
4
1
1
1
1
1
1
2
1
1
1
1
1
Platform Screw
Front Roller Adj. Bolt
Wire Harness
Speed Pot
Speed Knob
5/32” Allen Wrench
Choke
Belt Guide
Console Warning Decal
Isolator
Latch Catch
Frame Spacer (Left)
Magnet
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49*
50
Incline Pin
Endcap Washer
Storage Latch
Walking Belt
Cage Nut
Motor Belt
Wire Tie
Motor Tension Bolt
Motor Tension Washer
Tension Star Washer
Motor Pivot Nut
Motor/Pulley/Flywheel/Fan
Pulley/Flywheel/Fan
Motor
Motor Pivot Bolt
8” Cable Tie
Screw
Wire Tie Clamp
Frame Spacer (Right)
Walking Platform
Endcap
Left Foot Rail
Sensor Clip
Front Roller/Pulley
Electronic Screw
Ground Wire
Rear Roller Adj. Bolt
Left Rear Endcap
Upright Grommet
Allen Wrench
Hood
Hood Shield
1” Tek Screw
Isolator Fastener
Base Leg Pad
Motor Belly Pan
Controller
Frame Pivot Bolt
Frame Pivot Washer
Base
Latch Decal
Rear Roller
Frame
Console Lens
1 1/4” Tek Screw
Console Base
Motor Shield
Reed Switch Screw
Right Rear Endcap
Left Front Endcap
Right Front Endcap
Handrail Endcap
Right Handrail
4” Red Wire, Male/Female
Belt Guide Screw
Roller Adj. Washer
Wheel Bolt
Wheel
Frame Nut/Wheel Nut
Base Endcap
Circuit Breaker
Grommet
#
#
#
4” White Wire, Male/Female
4” Blue Wire, Male/Female
User’s Manual
Power Cord
Motor Tension Nut
Console Assembly
Right Foot Rail
* Includes all parts shown in the box
Note: “#” indicates a non-illustrated part.
Specifications are subject to change without notice. See the back cover of the user’s manual for information
about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|