Dual fuel
cookers
RC 9000 ..
GB
Users Op era t in g In st ru ct io n s
In st a lla t io n in st ru ct io n s
Before operating this cooker,
please read these instructions carefully
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Model RC 9000 ..
Page Number
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features and technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electronic programmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
How to use the hob burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
How to use the multifunction oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Do’s and do not’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Care and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
For the installer
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fitting the adjustable feet and levelling the cooker . . . . . . . . . . . . . . . . . .30
Stability bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Provision for ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Gas installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Conversion to Natural Gas or to LPG . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Lubrication of the gas taps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Electrical installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Appliance servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
3
Download from Www.Somanuals.com. All Manuals Search And Download.
In t ro d u ct io n
Congratulations on your purchase of this CDA cooker which has been carefully
designed and produced to give you many years of satisfactory use.
Before using this appliance it is essential that the following instructions are carefully
read and fully understood.
We would emphasise that the installation section must be fully complied with for your
safety to ensure that you obtain the maximum benefits from your appliance.
B
Assembling the
backguard
■ Remove the two spacers
“A” and the screw “B”
from the rear of the cook-
top.
■ Assemble the backguard
as shown in figure 1 and
fix it by screwing the cen-
tral screw “B” and the
spacers “A”.
A
Fig. 1
Declaration of CE conformity
✓
This cooker has been designed, constructed and marketed in compliance with:
- Safety requirements of EU Directive "Gas" 90/396/EEC;
- Safety requirements of EU Directive "Low Voltage" 2006/95/EC;
- Protection requirements of EU Directive "EMC" 89/336/EEC;
- Requirements of EU Directive 93/68/EEC.
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Fea t u res a n d t ech n ica l d a t a
Gas burners
1. Auxiliary burner (A)
2. Semi-rapid burner (SR)
3. Semi-rapid burner (SR)
4. Rapid burner (R)
1,00 kW
1,75 kW
1,75 kW
3,00 kW
3,50 kW
5. Triple-ring burner (TR)
5
3
4
1
2
Identification label
When you open the oven
door the indentification label
is at the bottom right hand
side.
Fig. 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro l p a n el
Fig. 3
9
A
U
T
O
1
2
3
4
5
6
7
8
CONTROL PANEL - Controls description
1. Electronic programmer
2. Multifunction oven switch knob
3. Multifunction oven thermostat knob
4. Front left burner control knob
5. Rear left burner control knob
6. Central burner control knob
7. Rear right burner control knob
8. Front right burner control knob
Pilot lamp:
9. Oven thermostat indicator light
Plea se n o t e: This appliance incorporates a safety cooling fan which you will hear
operating whenever the oven or grill are in use. The cooling fan may also operate
when the oven is switched off.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Elect ro n ic p ro g ra m m er
The electronic programmer is a device that groups together the following functions:
– 24 hour clock with illuminated display
– Timer (up to 23 hours and 59 minutes)
– Programme for automatic oven cooking
– Programme for semi-automatic oven cooking.
Description of the buttons:
Automatic cooking taking place
Timer
Timer in operation
Cooking time
and AUTO - flashing - Programme
error.
End of cooking time
(The time of day lies between the
calculated cooking start and end
time).
Manual position and cancellation
o f th e in se rte d co o kin g p ro -
gramme
Note: Select a function by the respec-
tive button and, in 5 seconds, set the
Advancement of the numbers of
all programmes
required time with the
(“one-hand” operation).
/
buttons
Turning back of the numbers of all
programmes and changing the
frequency of the audible signal.
A power cut zeroes the clock and can-
cels the set programmes.
Description of the lighted symbols:
AUTO - flashing - Programmer in auto-
matic position bu t n ot pro-
grammed
AUTO - always lighted - Programmer in
automatic position with pro-
gramme inserted.
A
U
T
O
Fig. 4
Fig. 5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Electronic clock (fig. 5)
Electronic timer
The programmer is equipped with an
electronic clock with lighted numbers
which indicate hours and minutes.
The timer programme consists only of a
buzzer which may be set for a maxi-
mum period of 23 hours and 59 min-
utes.
Upon immediate connection of the
oven or after a blackout, three zeroes
will flash on the programmer panel.
To set the hour it is necessary to push
If the AUTO is flashing push the
button.
To set the time, push the
and the or until you obtain the
desired time (fig. 7).
Having finished the setting, the normal
time will appear on the panel and the
symbol will appear.
The countdown will start immediately
and may be seen at any moment on
the panel by simply pressing the button
.
button
the
button and then the
or
button until you have set the exact
hour (fig. 5).
Alternatively, simultaneously push the
two buttons and at the same
time push the
or
button.
Note: Setting the clock deletes any pro-
gramme.
At the end of the time, the
symbol
will be switched off and an intermittent
buzzer will go off; this can be stopped
by pressing any one of the buttons.
Normal cooking w ithout
the use of the
programmer
To manually use the oven, that is, without
the aid of the programmer, it is necessary
to cancel the flashing AUTO by pushing
Altering the audible
signal
the button
and the symbol
(AUTO will be switched off
will go on - Fig. 6).
Attention: If the AUTO is not flashing
(which means a cooking programme has
already been inserted), by pushing the
By pressing the
button you can
choose from three variations.
button
you have cancelled the pro-
gramme and switched to manual.
A
U
T
O
Fig. 6
Fig. 7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3.Set the temperature and the cooking
programme by using the switch and
thermostat knobs of the oven (see
specific chapters).
Automatic oven
cooking
To cook food automatically in the oven,
it is necessary to:
1.Set the length of the cooking time
2.Set the end of the cooking time
3.Set the temperature and the oven
cooking programme.
Now the oven is prog rammed and
everything will work automatically, that
is the oven will turn on at the right
moment to end the cooking at the
established time.
These operations are done in the fol-
lowing way:
1.Set the length of the cooking time by
During cooking, the
on.
symbol remains
By pushing the
button you can see
the time that remains until the end of
cooking.
pushing the
button to
button and the
advance, or to go back
if you have passed the desired time
The cooking programme may be can-
(fig. 8). The AUTO and the
sym-
celled in any moment by pushing
.
bol will be on.
At the end of the cooking time the
oven will turn off automatically, the
symbol will turn off, AUTO will flash
and a buzzer will sound, which can be
turned off by pushing any of the but-
tons.
2.Set the end of the cooking time by
pressing the button (the cooking
time already added to the clock time
will appear), and the button (fig.
9); if you pass the desired time you
may get back by pushing the
ton.
but-
Turn the switch and thermostat knobs
to zero and put the programmer onto
After this setting, the
symbol will
go off. If after this setting, the AUTO
flashes on the panel and a buzzer
goes off, it means there was an error
in the programming.
In this case, modify the end of cook-
ing time or the cooking time itself by
follow in g th e above in stru ction s
again.
“manual” by pressing the
button.
At t e n t io n : A power cut makes the
clock go to zero and cancels the set
programmes.
After a power cut three zeroes will flash
on the panel.
A
U
T
A
U
T
O
O
Fig. 8
Fig. 9
9
Download from Www.Somanuals.com. All Manuals Search And Download.
At the end of cooking, the oven and
the symbol will turn off, the AUTO
will flash and a buzzer will sound; that
can be stopped by pushing any of the
buttons.
Turn the switch and thermostat knobs
to zero and put the programmer onto
Semi-automatic cooking
This is used to automatically switch off
the oven after the desired cooking time
has elapsed.
There are two ways to set your oven:
1. Set the length of the cooking time by
pushing the
button to ad van ce, or
button and the
to g o
“manual” by pressing the
button.
backwards if you have passed the
desired time (Fig. 10).
or
2. Set the end of the cooking time by
pushing the
bu tton to ad van ce, or
button and the
to g o
backwards if you have passed the
desired time (Fig. 11).
AUTO and the
symbol will be on.
Then set the temperature and the
cooking programme using the oven
switch and thermostat knobs (see
specific chapters).
The oven is switched on and it will
be switched off automatically at the
end of the desired time.
A
U
T
O
Du rin g co o kin g , th e
remains on and by pressing the but-
ton you can see the time that
symb o l
remains till the end of the cooking.
The cooking programme can be can-
celled at any moment by pushing the
button.
Fig. 10
A
U
T
O
Fig. 11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Ho w t o u se t h e h o b b u rn ers
Hob burners
Each hob burner is controlled by a sep-
arate gas tap operated by a control
knob (fig. 12) which has 3 positions
marked on the control panel, these are:
– Symbol ● : tap closed (burner off)
– Symbol
– Symbol
: High (maximum)
: Low (minimum)
Push in and turn the knob anti-clock-
wise to the selected position.
Fig. 12
To turn the burner off, fully rotate the knob clockwise to the off position: ●.
The maximum setting of the control tap is for boiling, the minimum setting is for slow
cooking and simmering.
All working positions must be choosen between the maximum and minimum setting,
never between the maximum setting and the “OFF” position.
Electric ignition
The sparks generated by the electrodes close to the burners will ignite the choosen
burner. Whenever the lighting of the burners is difficult due to peculiar conditions of
the gas features or supply, it is advised to repeat the ignition with the knob on “mini-
mum” position.
Lighting of the hob burners
To ignite the burner, the following instructions are to be followed:
1) Lightly press and turn the knob anti-clockwise, and position the knob indicator to the
symbol
printed on the control panel (fig. 12).
2) Press the knob to operate the electric ignition; or, in the case of a mains failure light
the burner with a match or lighted taper.
3) Adjust the burner according to the setting required.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Choice of burner
The burner must be choosen according to the diameter of the pans and energy
required.
Fig. 13
Burners
Auxiliary
Semi-rapid
Rapid
Pan diameter
12 ÷ 14 cm
16 ÷ 24 cm
24 ÷ 26 cm
26 ÷ 28 cm
max 36 cm
Triple-ring
Wok
do not use pans w ith concave or convex bases
Saucepans with handles which are excessively heavy, in relationship to the weight of
the pan, are safer as they are less likely to tip. Pans which are positioned centrally on
burners are more stable than those which are offset.
It is far safer to position the pan handles in such a way that they cannot be accidentally
knocked.
When deep fat frying fill the pan only one third full of oil.
DO NOT cover the pan with a lid and DO NOT leave the pan unattended.
In the unfortunate event of a fire, leave the pan where it is and turn off all controls.
Place a damp cloth or correct fitting lid over the pan to smother the flames.
DO NOT use water on the fire.
Leave the pan to cool for at least 30 minutes.
Correct use of triple-ring burner
The flat-bottomed pans are to be placed directly onto the pan-support.
To use the WOK you need to place the proper stand in order to avoid any faulty
operation of the triple-ring burner (Fig. 14a - 14b).
IMPORTANT:
The wok pan stand (fig. 14b) MUST BE PLACED ONLY over the pan-rest for the triple-
ring burner.
WRONG
CORRECT
Fig. 14b
Fig. 14a
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Ho w t o u se t h e Mu lt ifu n ct io n o ven
General features
As its name indicates, this is an oven that presents particular features from an opera-
tional point of view.
In fact, it is possible to insert 7 different programmes to satisfy every cooking need.
The 7 positions, thermostatically controlled, are obtained by 4 heating elements which
are:
– Bottom element
– Top element
– Grill element
1725 W
1725 W
2500 W
2500 W
– Circular element
Note:
Upon first use, it is advisable to operate the oven for 30 minutes in the position
and for
another 30 minutes at the maximum temperature (thermostat knob on position 250) in the
positions and , to eliminate possible traces of grease on the heating elements.
Clean the oven and accessories with warm water and washing-up liquid.
ATTENTION - MOST IMPORTANT
WARNING:
Pay special atten tion n ot to touch
the hot heating element inside the
oven cavity.
The door is hot, use the handle.
Operating principles
Heating and cooking in the MULTI-FUNCTION oven are obtained in the following
ways:
a. by normal convection
The heat is produced by the upper and lower heating elements.
b. by forced convection
A fan sucks in the air contained in the oven muffle, which sends it through the circu-
lar heating element and then sends it back through the muffle. Before the hot air is
sucked back again by the fan to repeat the described cycle, it envelops the food in
the oven, provoking a complete and rapid cooking.
It is possible to cook several dishes simultaneously.
c. by semi-forced convection
The heat produced by the upper and lower heating elements is distributed through-
out the oven by the fan.
d. by radiation
The heat is radiated by the infra red grill element.
e. by radiation and ventilation
The irradiated heat from the infra red grill element is distributed throughout the oven
by the fan.
f. by ventilation
The food is defrosted by using the fan only function without heat.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 16
Fig. 15
Thermostat knob (Fig. 16)
This only sets the cooking temperature and does not switch the oven on.
Rotate clockwise until the required temperature is reached (from 50 to 250°C).
The light between the thermostat and the function selector will illuminate when the
oven is switched on and turns off when the oven reaches the correct temperature.
The light will cycle on and off during cooking in line with the oven temperature.
Function selector knob (Fig. 15)
Rotate the knob clockwise to set the oven for one of the following functions.
Oven light
By setting the knob to this position, only the oven light comes on.
It remains on in all the cooking modes.
Traditional convection cooking
The upper and lower heating elements come on. The heat is dispersed by natural con-
vection and the temperature must be set to between 50° and 250°C via the thermo-
stat knob.
The oven must be preheated before cooking.
Recommended for:
Food that requires the same degree of cooking both inside and out, for example
roasts, spare pork ribs, meringues etc.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Grilling
The infrared grill element comes on. The heat is dispersed by radiation.
Use with the oven door closed and the thermostat knob to position 225°C for max
15 minutes, then to position 175°C.
For cooking hints, see the chapter “USE OF THE GRILL”.
Recommended for:
Intense grilling, browning, cooking au gratin and toasting etc.
It is recommended that you do not grill for longer than 30 minutes at any
one time.
Caution: the oven door becomes very hot during operation. Keep children
w ell out of reach.
Defrosting frozen foods
Only the oven fan comes on. Use with the thermostat knob set to “ ” - other positions
have no effect. The food is thawed by ventilation without heating.
Recommended for:
Quick thawing of frozen foods; one kg requires approximately 1 hour.
Thawing times vary according to the quantity and type of food to be thawed.
Hot air cooking
The circular element and fan come on. The heat is dispersed by forced convection and
the temperature can be regulated to between 50° and 250°C via the thermostat knob.
The oven does not require preheating.
Recommended for:
Food which has to be well-cooked outside and soft or rosy inside, for example
lasagne, lamb, roast beef, whole fish etc.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ventilated grill cooking
The infrared grill element and the fan come on. The heat is dispersed mainly by radia-
tion and the fan then distributes it all over the oven.
Use w ith the door closed. The temperature can be regulated via the thermostat
knob to between 50° and 175° max.
The oven must be preheated for approximately 5 minutes. For cooking hints, see the
chapter “GRILLING AND AU GRATIN.
Recommended for:
Grilling where quick browning on the outside is required to keep the juices in.
For example: veal steaks, chops, hamburgers etc.
It is recommended that you do not grill for longer than 30 minutes at any
one time.
Caution: the oven door becomes very hot during operation. Keep children
w ell out of reach.
Maintaining temperature after cooking or slow ly
heating foods
The upper heating element, the circular element and the fan come on.
The heat is dispersed by forced convection with greater intensity in the upper part.
The temperature can be set to between 50° and 140°C via the thermostat knob.
Recommended for:
Keeping food warm after any type of cooking. Slow heating of cooked food.
Convection cooking w ith ventilation
The upper and lower heating elements come on and the fan.
The heat coming from above and below is dispersed by convection with ventilation.
The temperature can be set to between 50° and 250°C via the thermostat knob.
Recommended for:
Voluminous dishes and large quantities which require the same degree of cooking
both inside and out, for example rolled roasts, turkey, roast legs, cakes etc.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooking advice
Sterilization
Sterilization of foods to be conserved, in full and hermetically sealed jars, is done in the
following way:
a. Set the switch to position
.
b. Set the thermostat knob to position 185 °C and preheat the oven.
c. Fill the dripping pan with hot water.
d. Set the jars onto the dripping pan making sure they do not touch each other and
the door and set the thermostat knob to position 135 °C.
When sterilization has begun, that is, when the contents of the jars start to bubble,
turn off the oven and let cool.
Regeneration
Set the switch to position
and the thermostat knob to position 150° C.
Bread becomes fragrant again if wet with a few drops of water and put into the oven
for about 10 minutes at the highest temperature.
Simultaneous cooking of different foods
The MULTI-FUNCTION oven set on position
and
gives a simultaneous heteroge-
neous cooking of different foods. Different foods such as fish, cake and meat can be
cooked together without mixing the smells and flavors together. This is possible since
the fats and vapors are oxidized while passing through the electrical element and there-
fore are not deposited onto the foods.
The only precaution to follow are:
– The cooking temperatures of the different foods must be as close to as possible, with
a maximum difference of 20° - 25 °C.
– The introduction of the different dishes in the oven must be done at different times in
relation to the cooking times of each one.
The time and energy saved with this type of cooking is obvious.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Grilling and “au gratin”
Grilling may be done without the roasting jack on position
the hot air completely envelops the food that is to be cooked.
of the switch, because
Set the thermostat to position 175 °C and after having preheated the oven, simply
place the food on the rack.
Close the door and let the oven operate with the thermostat on position 175 °C, until
grilling is done.
Adding a few dabs of butter before the end of the cooking time gives the golden “au
gratin” effect.
Grilling w ith the oven door closed.
It is recommended that you do not grill for longer than 30 minutes at any
one time.
Caution: the oven door becomes very hot during operation. Keep children
w ell out of reach.
Roasting
To obtain classical roasting, it is necessary to remember:
– that it is advisable to maintain a temperature between 180° and 200 °C.
– that the cooking time depends on the quantity and the type of foods.
Use of the grill
Preheat the oven for about 5 minutes.
Introduce the food to be cooked, positioning the rack as close to the grill as possible.
The dripping pan should be placed under the rack to catch the cooking juices and
fats.
Grilling w ith the oven door closed.
Do not grill for longer than 30 minutes at any one time.
Caution: the oven door becomes very hot during operation. Keep children
w ell out of reach.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Im p o rt a n t n o t es
Installation, and any demonstration, information or adjustments are not included in
the warranty.
The cooker must be installed by a qualified person in accordance with the relevant
Standards.
In the UK C.O.R.G.I registered installers are authorised to undertake the installation and
service work in compliance with the applicable regulations.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Do ’s a n d d o n o t ’s
Do’s and do not’s
• Do always grill with the oven door closed.
• Do read the user instructions carefully before using the cooker for first time.
• Do allow the oven to heat for one and a half hours, before using for the first time, in
order to expel any smell from the new oven insulation, without the introduction of
food.
• Do clean your oven regularly.
• Do remove spills as soon as they occur.
• Do always use oven gloves when removing food shelves and trays from the oven.
• Do not allow children near the cooker when in use.
• Do not allow fat or oils to build up in the oven trays, or oven base.
• Do not place cooking utensils or plates directly onto the oven base.
• Do not grill food containing fat without using the grid.
• Do not cover the grilling grid with aluminium-foil.
• Do not use the oven tray for roasting.
• Do not place hot enamel parts in water. Leave them to cool first.
• Do not allow vinegar, coffee, milk, saltwater, lemon or tomato juice to remain in con-
tact with enamel parts (inside the oven and on the oven tray).
• Do not use abrasive cleaners or powders that will scratch the surface of the stainless
steel and the enamel.
• Do not attempt to repair the internal workings of your oven.
• Do remove the protective film before the first use.
• Fire risk! Do not store flammable material in the oven and in the storage compart-
ment.
For your safety
The product should only be used for its intended purpose which is for the cooking of
domestic foodstuffs.
Under no circumstances should any external covers be removed for servicing or main-
tenance except by suitably qualified personnel.
Attention
Th e applian ce g ets very h ot, main ly aroun d th e cookin g areas. It is very
important that children are not left alone in the kitchen w hen you are cook-
ing.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Ca re a n d m a in t en a n ce
Important:
As a safety measure, before you start cleaning the cooker be sure to disconnect it from
the mains supply.
Do not use a steam cleaner because the moisture can get into the appliance
thus make it unsafe.
Th e use of suitable protective cloth in g/gloves is recommen ded w h en h an -
dling or cleaning of this appliance.
WARNING
When correctly installed, your product meets all safety requirements laid down for this
type of product category.
However special care should be taken around the rear or the underneath of the appli-
ance as these areas are not designed or intended to be touched and may contain
sharp or rough edges, that may cause injury.
Flexible tube
From time to time, check the flexible tube connecting the gas supply to the cooker.
It must be always in perfect condition; in case of damage arrange for it to be replaced
by a C.O.R.G.I. registered installer.
Gas taps
If a tap becomes stiff, do not force; contact your local Service Centre.
Cleaning the hob
Spillage on the hob can usually be removed by a damp soapy cloth. More obstinate
stains can be removed by rubbing gently with a soapy nylon (non metal) scouring pad
or mild household cleaner.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Enamelled parts
All the enamelled parts must be cleaned with a sponge and soapy water only or other
non-abrasive products.
Dry preferably with a microfibre or soft cloth.
Stainless steel, aluminium, painted parts and silk-
screen printed surfaces
Clean using an appropriate product. Always dry thoroughly.
Stainless steel surfaces: can be cleaned with an appropriate stainless steel cleaner.
IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abra-
sion. You are advised to use a soft cloth and neutral soap.
CAUTION: Do not use abrasive substances or non-neutral detergents as these w ill
irreparably damage the surface.
Changing the oven light
1. Disconnect the electrical power supply (for example, by switching off the main
power switch).
2. Unscrew the light cover
3. Fit a new bulb.
4. Refit the cover.
Note:
Use only bulbs designed to resist up to 300°C with the following characteristics: 230 V,
type E14 and same power (check watt power as stamped in the bulb itself) of the
replaced bulb
.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Burners
They can be removed and washed only
with soapy water.
Detergents can be used but must not be
abrasive or corrosive.
C
Do not use abrasive sponges or pads.
Do not put in dishwasher.
After each cleaning, make sure that the
burner-caps, as well as the burners, have
been well wiped off and CORRECTLY
POSITIONED.
It is essential to check that the burner
flame distributor F and the cap C has
been correctly positioned (see fig. 17) -
failure to do so can cause serious prob-
lems.
Check that the electrode “S” (fig. 17) is
always clean to ensure trouble-free spark-
ing.
F
S
Fig. 17
Note:
The electrode “S” must be very carefully cleaned.
To avoid damage to the electric ignition do not use it w hen the burners are not
in place.
Triple ring burner
The triple ring burner must be correctly positioned (see figs. 18-19); the burner rib
must be located correctly in the burner base as shown by the arrow.
The burner correctly positioned must not rotate (fig. 19).
Then position the cap A and the ring B (fig. 19).
B
A
Fig. 18
Fig. 19
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Removal of the inner glass door panel
– The inner glass door panel can easily be removed for cleaning by unscrewing
the four screws (fig. 20).
– When re-assembly ensure that the inner glass is correctly positioned and do not
over tighten the screws.
Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven
door glass since they can scratch the surface, w hich may result in shattering
of the glass.
Fig. 20
Storage compartment
– The storage compartment is accessible through the pivoting panel.
Attention: Do not store flammable material in the oven, or the storage com-
partment.
Fig. 21
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Inside of oven
The oven should always be cleaned
after use when it has cooled down.
The cavity should be cleaned using a
mild d eterg en t solution an d w arm
w ater. Suitable proprietary chemical
cleaners may be used after first consult-
ing with the manufacturers recommen-
dations and testing a small sample of the
oven cavity. Abrasive cleaning agents or
scouring pads/cloths should not be used
on the cavity surface.
NOTE: The manufacturers of this appli-
ance will accept no responsibility for
damage caused by chemical or abrasive
cleaning.
Fig. 22
Let the oven cool dow n and pay spe-
cia l a tten tion n o to tou ch th e h ot
heating elements inside the oven cav-
ity.
Assembling and
dismantling of the side
runner frames
– Fit the side runner frames into the
holes on the side walls inside the
oven (Fig. 22).
– Slide the tray and rack into the run-
ners (Fig. 23).
The rack must be fitted so that the
safety catch, which stops it sliding
out, faces the inside of the oven.
– To dismantle, operate in reverse
order.
Fig. 23
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven tray
The oven tray must be correctly placed on the wire support (fig. 24) then inserted into
the side runners (fig. 25).
Oven floor
The oven floor “F” (fig. 25) can be easily removed to facilitate cleaning.
Remember to replace the floor correctly afterwards.
Be careful not to confuse the tray “L” with the oven floor “F”.
Fig. 24
L
F
Fig. 25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 26a
Fig. 26b
Fig. 26c
Fig. 26d
Removing the oven
door
Please operate as follows:
●
●
Open the door completely.
The swivel retainers of the rh and lh
hinges (fig. 26a) are hooked onto
the metal bar above them (fig. 26b).
●
●
Lift the oven door slightly. The noch
on the bottom of the hinge will dis-
engage (fig. 26c).
Now pull the oven door forwards off
the appliance. Release both hinge
sections from the slots (fig. 26d).
Door assembly
●
Grip the door (as indicated in figure
26) and refit it in reverse order of
removing procedure.
Fig. 26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR THE
INSTALLER
The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but
not in a room or space containing a bath or a shower.
The appliance must not be installed in a bed-sitting room of less than 20 m3.
The appliance is designed and approved for domestic use only and should not be
installed in a commercial, semi commercial or communal environment.
Your product will not be guaranteed if installed in any of the above environments and
could affect any third party or public liability insurances you may have.
.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Lo ca t io n
This cooker has class “2/1” overheating protection so that it can be installed
next to a cabinet.
If the cooker is installed adjacent to furniture which is higher than the gas hob cook-
top, a gap of at least 200 mm must be left between the side of the cooker and the fur-
niture.
The furniture walls adjacent to the cooker must be made of material resistant to heat.
The veneered synthetic material and the glue used must be resistant to a temperature
of 90°C in order to avoid ungluing or deformations.
The cooker may be located in a kitchen, a kitchen/diner or bed-sitting room but not in
a room containing a bath or shower.
Curtains must not be fitted immediatly behind appliance or within 500 mm of the sides.
It is essential that the cooker is positioned as stated below.
The cooker must be installed by a qualified technician and in compliance w ith
local safety standards.
If the cooker is located on a pedestal it is necessary to provide safety measures to pre-
vent falling out.
200 mm
500 mm
A
U
T
O
Fig. 27
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Fit t in g t h e a d ju st a b le feet
The adjustable feet must be fitted
to the base of the cooker before
use.
Rest the rear of the cooker an a
piece of the polystyrene packaging
exposing the base for the fitting of
the feet.
Fit the 4 legs by screwing them
tight into the support base as
shown in picture 29.
Fig. 28
WARNING
When raising cooker to upright
p o sit io n a lw a ys e n su re t w o
people carry out th is man oeu-
vre to preven t d amag e to th e
adjustable feet (fig. 30).
Fig. 29
Fig. 30
30
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Be carefull: do n ot lift th e cooker
by th e d oor h an d le w h en raisin g
to the upright position (fig. 31).
WARNING
When moving cooker to its final posi-
tion DO NOT DRAG (fig. 32).
Lift feet clear of floor (fig. 30).
Fig. 31
Fig. 32
Levelling the cooker
The cooker may be levelled by screw-
ing the lower ends of the feet IN or
OUT (fig. 33).
Fig. 33
31
Download from Www.Somanuals.com. All Manuals Search And Download.
St a b ilit y b ra cket
We recommend a stability bracket is fitted to the cooker.
The type shown in fig. 34 can be purchased from most plumbers merchants and
do it yourself (D.I.Y.) shops.
Existing slot in
rear of cooker
Brackets
Fig. 34
Dotted line showing the
position of cooker when fixed
Outline of cooker
backplate at the
engagement slot
Floor fixing
Wall fixing
Dimension is in millimetres
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Pro viso n fo r ven t ila t io n
✓ The appliance should be installed into a room or space with an air supply in accor-
dance with BS 5440-2: 2000.
✓ For rooms with a volume of less than 5 m3 - permanent ventilation of 100 cm2 free
area will be required.
✓ For rooms with a volume of between 5 m3 and 10 m3 a permanent ventilation of
50 cm2 free area will be required unless the room has a door which opens directly to
the outside air in which case no permanent ventilation is required.
✓ For rooms with a volume greater than 10 m3 - no permanent ventilation is required.
NB. Regardless of room size, all rooms containing the appliance must have
direct access to the outside air via an openable w indow or equivalent.
✓ Where there are other fuel burning appliances in the same room, BS 5440-2: 2000
should be consulted to determine the correct amount of free area ventilation require-
ments.
✓ The above requirements allow also for use of a gas oven and grill but if there are
other gas burning appliances in the same room, consult a qualified engineer.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Ga s in st a lla t io n
IMPORTANT NOTE
This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation
label attached on the appliance).
✓ Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and
cannot be used on any other gas (LPG) without modification. The appliances are
manufactured for conversion to LPG.
✓ Appliances supplied for use on LPG: they are adjusted for this gas only and cannot
be used on any other gas (NATURAL GAS) without modification. The appliances are
manufactured for conversion to NATURAL GAS.
If the NATURAL GAS/LPG conversion kit is not supplied with the appliance this kit can
be purchased by contacting the After-Sales Service.
INSTALLATION & SERVICE REGULATIONS (UNITED KINGDOM)
It is a legal requirement that all gas appliances are Installed & Serviced by a competent
person in accordance with the current editions of the following Standards &
Regulations or those regulations appropriate to the geographical region in which they
are to be installed:
✓ Gas Safety (Installation & Use) Regulations
✓ Building Regulations
✓ British Standards
✓ Regulations for Electrical Installation
Installation and service of any gas product must be made by a suitably qualified person
competent on the type of product being installed or serviced and holding a valid
certificate of competence for the work being carried out. Currently the proof of
competence is the Accredited Certification Scheme (ACS) or S/NVQ that has been
aligned to the ACS.
It is also a requirement that all businesses or self employed installers are members of a
class of person approved by the Health and Safety Executive. Currently the only body
with such approval is CORGI.
Failure to install the appliance correctly could invalidate any manufacturers warranty
and lead to prosecution under the above quoted regulation.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Ga s co n n ect io n
The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a
C.O.R.G.I. registered installer. Installers shall take due account of the provisions of the
relevant British Standards Code of Practice, the Gas Safety Regulations and the Building
Standards (Scotland)(Consolidation) Regulations issued by the Scottish Development
Department.
Installation to Natural Gas
Installation to Natural Gas must conform to the Code of Practice, etc.
The supply pressure for Natural Gas is 20 mbar.
The installation must conform to the relevant British Standards.
Installation to LP Gas
When operating on Butane gas a supply pressure of 28-30 mbar is required. When
using Propane gas a supply pressure of 37 mbar is required.
The installation must conform to the relevant British Standards.
Warning: Only a C.O.R.G.I. registered installer, also with technical knowledge of elec-
tricity should install the appliance. He should observe the Regulations and Codes of
Practice governing such installation of gas appliances.
Note: It is recommended that the gas connection to the appliance is installed with a
flexible connecting tube made to BS5386.
No t es:
✓ Flexible hoses can be used w here the sited ambient temperature of the
h o se d o e s n o t e xce e d 7 0 °C. Th e se h o se s m u st b e m a n u fa ctu re d in
accordance w ith BS669 part 1 and be of the correct construction for the
type of gas being used.
✓ Gas hoses designed for natural gas MUST NOT be used for supplying LPG
gas (LPG gas hoses can be identified by a either a red band or stripe on
the rubber outer coating of the hose).
The hose should not be crushed or trapped or be in contact w ith sharp or
abrasive edges.
Using a suitable leak detection fluid solution (e.g. Rocol) check each gas connection
one at a time by brushing the solution over the connection.
The presence of bubbles will indicate a leak.
If there is a leak, tighten the fitting and then recheck for leaks.
IMPORTANT!
Do not use a naked flame to test for leaks.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
GB
Gas connection
Cat: II 2H3+
The gas supply must use the nearest gas inlet pipe which is located at the left or the
right hand side at the rear of the appliance (figs. 35, 37).
The hose should also be connected in such away that it does not touch the floor.
To screw the connecting tube operate with two spanners (fig. 36).
The unused end inlet pipe must be closed with the plug interposing the gasket.
After connecting to the mains, check that the coupling are correctly sealed,
using soapy solution, but never a flame.
Left gas
inlet pipe
Right gas
inlet pipe
Fig. 36
Plug
1/2” BSP (male)
Fig. 35
36
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRESCRIPTIONS FOR GAS CONNECTION
Rear wall
Suggested area for
gas mains connection
Fig. 37
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n versio n t o Na t u ra l Ga s o r t o LPG
Injectors replacement of top burners
Every cooker is provided with a set of injectors for the various types of gas.
Injectors not supplied can be obtained from the After-Sales Service.
Select the injectors to be replaced according to the table at page 40.
The nozzle diameters, expressed in hundredths of a millimetre, are marked on the
body of each injector.
To replace the injectors proceed as follows:
– Remove the grids and extract the burner bodies.
– Using a wrench, substitute the nozzle injectors “J” (Figs. 38 - 39) with those most
suitable for the kind of gas for which it is to be used (see “Table for the choice of the
injectors”).
The burners are constructed in such a w ay so as not to require the regulation
of the primary air.
J
J
Fig. 38
38
Fig. 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting of the minimum of the top burners
Considering that in the minimum position the flame must have a length of about 4 mm
and must remain lit even with a quick turn from the maximum position to that of
minimum.
The flame adjustment is done in the following way:
– Turn on the burner
– Tum the tap to the MINIMUM position
– Take off the knob
– With a small flat screwdriver turn the screw inside the tap rod to the correct
regulation (fig. 40).
Normally for LPG, tighten up the regulation screw.
Fig. 40
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Table for the choice of the injectors
GB
Cat: II 2H3+
G 30 - 28-30 mbar
G 31 - 37 mbar
G 20
20 mbar
Reduced
Power
Nominal
Power
BURNERS
By-pass
[1/100 mm]
By-pass
[1/100 mm]
Ø injector
[1/100 mm]
Ø injector
[1/100 mm]
[kW]
[kW]
Auxiliary (A)
Semi-rapid (SR)
Rapid (R)
1,00
1,75
3,00
3,50
0,30
0,45
0,75
1,50
27
32
42
65
50
65
85
95
72 (X)
97 (Z)
115 (Y)
135 (T)
Triple-ring (TR)
INCREASE OF AIR NECESSARY FOR GAS COMBUSTION (2 m3/h x kW)
BURNERS
Air necessary for combustion [m3/h]
2,00
Auxiliary (A)
Semi-rapid (SR)
Rapid (R)
3,50
6,00
7,00
Triple-ring (TR)
Lu b rica t io n o f t h e g a s t a p s
The operations must be executed by a qualified technician.
IMPORTANT
All in terven tion regardin g in stallation main ten an ce an d con version of th e
appliance must be fulfilled w ith original factory parts.
The manufacturer declines any liability resulting from the non-compliance of
this obligation.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Elect rica l in st a lla t io n
The appliance must be connected to the electrical network verifying above all that the
voltage corresponds to the value indicated on the specifications plate and that the
cables section of the electrical plant can bear the load which is also indicated on the
plate.
The cooker can be connected directly to the mains placing an omnipolar switch with
minimum opening between the contacts of 3 mm between the appliance and the
mains.
The power supply cable must not touch the hot parts and must be positioned so that it
does not exceed 75°C at any point.
Once the cooker has been installed, the switch must always be accessible.
Before effecting any intervention on the electrical parts the appliance must
be disconnected from the netw ork.
Warning!
Electricity can be extremely dangerous.
This appliance must be earthed.
D
PE
Connecting feeder cable
To connect the feeder cable to the cook-
er it is necessary to:
– Remove the screw that hold shield “A”
behind the cooker (fig. 41).
– Insert the feeder cable of the suitable
section (as described in the next chap-
B
ter) into the cable clamp “D”.
– Connect the phase and earth cables to
the terminal block “B” according to the
A
diagram in figure 42.
Fig. 41
– Pull the feeder cable and block it with
cable clamp “D”.
– Re-mount shield “A”.
230 V
Feeder cable section
TYPE HO5RR-F
L1 N PE
230 V
3 x 1,5 mm2
(L2)
Fig. 42
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p lia n ce servicin g
CDA p rovid e a q u a lity a n d effective a fter-sa les service to cover a ll you r
servicing needs.
Please attach your receipt to this page for safekeeping.
Please h elp us to h elp you by h avin g th e follow in g in formation available
w hen booking a service-call:
1. Model type, make and model – see the product data plate.
2. Evidence of installation / purchase date
3. Retailer where appliance was purchased
4. Clear and concise details of the fault
5. Full address including postcode and any contact phone numbers
Contact telephone numbers
CDA Customer Care Department
• Telephone: 01949 862012
• Fax: 01949 862003
• Email: service@cda.eu
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Gu a ra n t ee
CDA appliances carry a five-year parts and a one-year labour guarantee.
CDA will repair or replace any defect or part attributable to faulty material or workman-
ship. Within the first year this will be free of both labour and parts charges. After the
first year and within five years, the parts will be supplied free of charge provided that
the repair is carried out by an agent authorised by CDA and the labour will be charged
at the commercial rate applicable at the time of repair.
The appliance must have been installed by a suitably qualified person and in accor-
dance with the manufacturer’s instructions and current legislation. The guarantee does
not cover faults caused by the incorrect fitting of appliances.
Limit of Cover
• The guarantee does not cover cosmetic damage e.g. discolouration or oxidisation.
• Proof of purchase or installation date must be produced before a service-call will be
booked.
• The appliance must be used for domestic purposes only. Appliances used for com-
mercial or professional purposes are not covered by the guarantee. Commercial war-
ranty is available at extra cost.
• The appliance must not be modified or tampered with or repair attempted by any
unauthorised person.
• The guarantee does not cover damage caused in transit or by misuse, accident,
abuse or neglect.
• The guarantee does not cover routine maintenance.
• Use of parts not supplied or recommended by |C|D|A| will invalidate the warranty.
• Rubber seals, filters, removable glass parts, control knobs and buttons, fuses and
light bulbs will need replacing periodically and are not covered by the guarantee.
• Second-hand or reconditioned appliances are not covered by the guarantee.
The conditions under which this guarantee is offered are in addition to the statutory
rights of the domestic purchaser and these statutory rights are not affected by this
guarantee.
CDA reserve the right to change specification without prior notice.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Descriptions and illustrations in this booklet are given as simply indicative.
The manufacturer reserves the right, considering the characteristics of the models described here, at
any time and without notice, to make eventual necessary modifications for their construction or for
commercial needs.
Cod. 1103119
ß5
RC 9 0 0 0 .. co o kers
The
Group Ltd
●
●
●
●
Harby Road Langar Nottingham NG13 9HY UK
●
VAT No : 528 7168 19 Registered in England : 2621460
Download from Www.Somanuals.com. All Manuals Search And Download.
|