NIGHT WATCH
3 x 32
digital night vision
w/ Color lCd
InstructIon
manual
Model #: 263230CL
Lit. #: 98-1588/03-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Congratulations on the purchase of your Bushnell® Night Watch Digital Color Night Vision. Comprised of high quality electronics
and optics, this Bushnell Night Watch unit is a hand-held digital night vision viewing system that utilizes a low-light charge coupled
device (CCD) sensor providing images comparable to generation 2 & 3 resolution. Day and Night time images are magnified and
displayed on a Color LCD micro display screen, which provides a color image when ambient light conditions are high enough,
and a desaturated color or neutral, monochrome image (not the typical "green screen" night vision) under lower ambient
light conditions. The Digital Color Night Vision also contains an RCA video output port which allows live transmission to video
camcorders, computer lap tops / monitors, and television screens.
HoW DIGItal nIGHt VIsIon WorKs
Bushnell Digital Night Vision products collect existing light through the objective lens. The light is then processed through a highly
sensitive CCD sensor and transferred to the micro liquid crystal display (color LCD). Images viewed on the LCD are magnified 3
times. An infrared illuminator provides a light source to enable viewing in total darkness.
The Bushnell Night Watch Digital Color Night Vision unit is ideal for camping, caving, scouting, maritime navigation, and observing
wildlife under the veil of darkness, patrolling warehouses and similar surveillance operations where light is scarce.
oPEratInG InsructIons
1. Slide the battery compartment door (2) open in the direction of the white arrow. Insert two CR123 batteries (3v lithium, not
included) into the battery compartment. Be sure to observe the correct battery polarity, as shown on the left. The "+" end of the
top battery should be facing out (towards the battery door), and the "-" end of the lower battery should be facing out.
2. Remove the front lens cover. When finished using the unit, replace the cover to protect the objective lens (1) and IR light (7).
3. Press the ON/OFF switch (3) to power the device on. A green LED light (4) indicates that the power is on. To extend battery life, the
unit will normally turn off automatically after 2 minutes (if no buttons are pressed). To cancel this auto-off function, briefly press
and release the IR switch (8) on the top of the unit. The power will then remain on until you turn it off manually with the ON/OFF
switch. The orange light on the lower half of the power indicator light (4) will glow if the unit is in auto-off mode (default), and will
turn off if you cancel the auto-off function. If the batteries become weak, the green power indicator LED will blink.
4. View through the eyepiece (5) and select an object to focus on.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. To focus the image, first rotate the eyepiece rubber ring (5) until the edges of the LCD display appear sharp to your vision. Next,
rotate the objective lens focus wheel (6) until the object is in focus and the view is clearest. At this point, the display focus (eyepiece
ring) is set for your individual eyesight and will not require further adjustment when viewing objects at different distances. When
changing the viewing distance, simply rotate the main focus wheel (6) until the image is in focus.
6. The Digital Night Vision has a light level sensor on the front of the unit (14) which detects low light conditions and automatically
turns on an infrared illuminator (7) to improve image quality. When the IR light is on, this is indicated by the red LED (9) above the
power indicator. You can also turn the IR illuminator on manually anytime, even if ambient light levels are high, by pressing and
holding the IR switch (8) for a at least two seconds (when you release the switch, you will see the red IR illuminator LED indicator,
confirming the IR illuminator is on now).
7. To increase the brightness of the IR illuminator, press the "+" key (10). This can be used to extend your viewing distance. To decrease
the brightness of the IR illuminator, press the "-" key. This can be helpful in improving the LCD display viewing quality (by avoiding
"wash out") in very low light conditions or complete darkness.
8. While moving from viewing one object to another object, it might be necessary to rotate the objective lens focus wheel and adjust
the IR illuminator brightness in order to achieve the best image quality.
9. The Digital Night Vision includes a video output ("TV Out") jack (13). This port allows one to transmit images to an external video
monitor or video recorder. Plug the output video cable into the video output jack ("TV Out"). When the Digital Color Night Vision
is connected to compatible (NTSC) video equipment, the image produced by the unit can be monitored and/or recorded.
10. The Digital Color Night Vision also includes a 6 volt auxiliary power input jack (12). To connect the Digital Night Vision to a
household outlet, use the included 6 volt AC power adapter. Note that this feature is not intended to recharge batteries of any type,
and should not be used for that purpose. It simply provides an option for an external power source.
notE: When the batteries are inserted and the external power source is turned on, the device operates on the external power
source. If you unplug the external power source, and you want to use the battery source, you have to press the ON button (3) to
make the device operate.
notE: A standard tripod mounting socket is provided on the bottom of the unit. Remove the round rubber plug near the center of
the bottom face of the unit and set it aside.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
trouBlEsHootInG
unit will not turn on
1. Check that the batteries are installed correctly (2). If the batteries are installed correctly and the batteries are good, then the green
LED indicator light should be on steadily.
2. Check that the power button (3) has been pressed.
Power does not stay on
1. Replace the batteries when they become weak.
2. The unit normally turns off automatically after 2 minutes to conserve battery power. To defeat this, briefly press the IR switch.
Image is not focused.
1. Adjust the objective focus wheel (6) and eyepiece display focus (5).
2. Make sure you are not too close to the object you are viewing.
carE anD maIntEnancE
Your Bushnell Digital Night Vision device was designed to provide many years of reliable service. To ensure that you get the most
enjoyment out of your Digital Night Vision device, always obey the following warnings and precautions.
•
•
•
•
Do not open the body of the device or otherwise attempt to service this device.
Always store the device in a dry, well ventilated room.
Keep the device away from any heating and air conditioning vents or other heating devices, direct sunlight, and moisture.
Avoid dropping or otherwise shocking the unit. Although designed for rugged outdoor use, this device incorporates a sophisticated
digital circuitry which could be damaged in extreme cases of misuse.
•
•
•
•
•
Clean the optical lens with a professional lens cleaning supplies.
Clean the exterior of the device with a soft clean cloth.
Avoid removing the eyepiece as the LCD display could become damaged.
Do not leave the device in direct sunlight or rain.
Remove the batteries if the device will not be used for longer than a few weeks.
For any other problems or questions, please contact Bushnell Customer Service at:
Download from Www.Somanuals.com. All Manuals Search And Download.
5
TWO-Year LIMITED WARRANTY
®
Your Bushnell product is warranted to be free of defects in materials and workmanship for two years after the date of
purchase. In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that
you return the product postage prepaid. This warranty does not cover damages caused by misuse, improper handling,
installation, or maintenance provided by someone other than a Bushnell Authorized Service Department.
Any return made under this warranty must be accompanied by the items listed below:
1) A check/money order in the amount of $10.00 to cover the cost of postage and handling
2) Name and address for product return
3) An explanation of the defect
4) Proof of Date Purchased
5) Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, with return postage
prepaid to the address listed below:
IN U.S.A. Send To:
Bushnell Outdoor Products
Attn.: Repairs
IN CANADA Send To:
Bushnell Outdoor Products
Attn.: Repairs
8500 Marshall Drive
Lenexa, Kansas 66214
25A East Pearce Street, Unit 1
Richmond Hill, Ontario L4B 2M9
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty
information. In Europe you may also contact Bushnell at:
Bushnell Germany GmbH
European Service Centre
Mathias-Brüggen-Str. 80
D-50827 Köln
GERMANY
Tél: +49 221 995568-0
Fax: +49 221 995568-20
This warranty gives you specific legal rights.
You may have other rights which vary from country to country.
©2010 Bushnell Outdoor Products
6
Download from Www.Somanuals.com. All Manuals Search And Download.
sPEcIFIcatIons
Magnification:
Objective Size:
Battery Type:
Viewing Range:
Field of View:
Operating Temperature Range:
Dimensions:
Weight:
3x
32 mm
Two CR123 (3v, lithium) batteries (not included)
1-328 ft. / .3-100m
70 ft @ 100 yds / 23m @ 100m
14-104 / -10 ~ 40 C (Humidity >90%)
5.9 x 3.8 x 2.0 in. / 150 x 95 x 51 mm
13.4 oz. /380g
Tripod Mountable:
Video Out:
Yes
NTSC video standard.
Note: low ambient light operation may create low signal levels.
6V DC, 1A, plug polarity=positive tip
External AC Power Adapter:
FCC Note:
is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. ese limits are designed
to provide reasonable protection against harmful interference in a residential installation. is equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
·
Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cable must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO
THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT.
Specifications and designs are subject to change without any notice or obligation on the part of the manufacturer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
©2010 Bushnell Outdoor Products
Download from Www.Somanuals.com. All Manuals Search And Download.
|