®
BUSH HOG
MP 5/ MP 6
MULCH PRO
Operator’s Manual
ASSEMBLY ꢀꢀOPERATION ꢀꢀMAINTENANCE
798
$4.00
50018726
Download from Www.Somanuals.com. All Manuals Search And Download.
MP 5/6
Operator’s Manual
TABLE OF CONTENTS
SECTION/PARA
PAGE
SECTION/PARA
PAGE
Warranty....................................................3
Dealer Preparation Check List ..................4
Safety Precautions ....................................5
Federal Laws and Regulations..................6
IV MAINTENANCE .......................................12
4-1 Maintenance Check List.....................12
4-2 Lubrication..........................................12
4-3 Belt Adjustment..................................13
4-4 Belt Replacement...............................13
4-5 Blade Replacement............................14
4-6 Blade Spindle Service........................15
4-7 Troubleshooting..................................16
I
INTRODUCTION AND DESCRIPTION......7
1-1 Introduction ..........................................7
1-2 Description ...........................................7
II PREPARATION FOR USE .........................8
2-1 Attaching to Tractor ..............................8
V DEALER ASSEMBLY...............................17
5-1 Base Unit Assembly...........................17
Safety Decals ...........................................19
Torque Specifications ...............................20
III OPERATING INSTRUCTIONS.................10
3-1 General Safety ...................................10
3-2 Cutting Height Adjustment .................10
3-3 Operation ...........................................10
3-4 Transporting .......................................10
Tips On Mulching ................................... 11
RETAIL CUSTOMER’S RESPONSIBILITY
UNDER THE BUSH HOG WARRANTY
It is the Retail Customer and/or Operator’s responsibility to read the Operator’s
Manual, to operate, lubricate, maintain and store the product in accordance with all
instructions and safety procedures. Failure of the operator to read the Operator’s
Manual is a misuse of this equipment.
It is the Retail Customer and/or Operator’s responsibility to inspect the product and to
have any part(s) repaired or replaced when continued operation would cause damage
or excessive wear to other parts or cause a safety hazard.
It is the Retail Customer’s responsibility to deliver the product to the authorized Bush
Hog Dealer, from whom he purchased it, for service or replacement of defective parts
which are covered by warranty. Repairs to be submitted for warranty consideration
must be made within forty-five (45) days of failure.
It is the Retail Customer’s responsibility for any cost incurred by the Dealer for travel-
ing to or hauling of the product for the purpose of performing a warranty obligation or
inspection.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
®
BUSH HOG
LIMITED WARRANTY
✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯
Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an
authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period
of one (1) year for non-commercial, state, and municipalities’ use and ninety (90) days for commercial use from
date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or
replacement of defective parts.
Replacement or repair parts installed in the equipment covered by this limited warranty are warranted
for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equip-
ment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an
authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equip-
ment or parts which are claimed to have been defective in material or workmanship.
DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES
Bush Hog’s obligation under this limited warranty, to the extent allowed by law, is in lieu of all war-
ranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to
the sale or use of the items warranted. Such incidental and consequential damages shall include but not be
limited to: transportation charges other than normal freight charges; cost of installation other than cost
approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of
income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of
equipment or parts resulting from acts beyond the control of Bush Hog.
THIS LIMITED WARRANTY SHALL NOT APPLY:
1. To vendor items which carry their own warranties, such as engines, tires, and tubes.
2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident.
3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judge-
ment of Bush Hog such use affects its performance, stability or reliability.
4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner
which, in the sole judgement of Bush Hog, affects its performance, stability or reliability.
5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid,
worn blades, or to normal deterioration of such things as belts and exterior finish due to use or
exposure.
6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the
company’s sole judgement is a wear item.
NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIM-
ITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE
IN WRITING AND SIGNED BY BUSH HOG’S SERVICE MANAGER, POST OFFICE BOX 1039, SELMA,
ALABAMA 36702-1039.
✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯
Record the model number, serial number and date
purchased. This information will be helpful to your
MODEL NUMBER
dealer if parts or service are required.
SERIAL NUMBER
MAKE CERTAIN THE WARRANTY REGISTRATION
CARD HAS BEEN FILED WITH BUSH HOG/
DATE OF RETAIL SALE
SELMA, ALABAMA
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DEALER PREPARATION CHECK LIST
MP 5/6 Finishing Mowers
BEFORE DELIVERING MACHINE — The following check list should be completed.
Use the Operator’s Manual as a guide.
❒ 1. Assembled completed.
❒ 2. Gearboxes filled with oil.
❒ 3. All fittings lubricated.
❒ 4. All shields in place and in good condition.
❒ 5. All fasteners torqued to specifications given in Torque Chart
❒ 6. All decals in place and readable. (See decal page.)
❒ 7. Overall condition good (i.e. paint, welds)
❒ 8. Operators manual has been delivered to owner and he has been instructed
on the safe and proper use of the cutter.
Dealer’s
Signature
Purchaser’s
Signature
THIS CHECKLIST TO REMAIN IN OWNER’S MANUAL
It is the responsibility of the dealer to complete the procedures listed
above before delivery of this implement to the customer.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY PRECAUTIONS
This symbol is used to call attention to safe-
ty precautions that should be followed by
the operator to avoid accidents. When you
see this symbol, carefully read the message
that follows and heed its advice. Failure to
comply with safety precautions could result
in serious bodily injury.
In addition to the design and configuration of equipment, hazard control and accident prevention are depen-
dent upon the awareness, concern, prudence and proper training of personnel in the operation, transport,
maintenance and storage of equipment. Lack of attention to safety can result in accident, personal injury,
reduction of efficiency and worst of all—loss of life. Watch for safety hazards and correct deficiencies prompt-
ly. Use the following safety precautions as a general guide to safe operations when using this machine.
Additional safety precautions are used throughout this manual for specific operating and maintenance proce-
dures. Read this manual and review the safety precautions often until you know the limitations.
1. Read the Operator’s Manual. Failure to read the Operator’s Manual is considered a misuse of this
equipment.
2. Become familiar with all the machine’s controls and all the caution, warning and danger decals affixed
to the machine before attempting to start or operate.
3. Before starting or operating the machine, make a walk around inspection and check for obvious
defects such as loose mounting bolts and damaged components. Correct any deficiency before
starting.
4. Do not allow children to operate the cutter. Do not allow adults to operate it without proper instruction.
5. Do not carry passengers.
6. Keep the area of operation clear of all persons, particularly small children and pets. The operator
should cease mowing whenever anyone comes within the operating area.
7. Clear the work area of objects which might be picked up and thrown.
8. Use a piece of cardboard or wood rather than hands to search for hydraulic leaks. Escaping hydraulic
oil under pressure can penetrate skin. If fluid is injected into the skin, it must be surgically removed
within a few hours by a doctor familiar with this form of injury or gangrene may result.
9. Do not operate without all guards and shields in place and in good condition.
10. Lower implement to ground, stop tractor engine, apply parking brake, and allow blades to completely
stop before leaving the tractor.
11. Keep hands and feet away from blades.
12. This cutter is not to be operated along highways or in any area where people may be present unless
all sides of the unit are enclosed by permanent bands, safety chains or other factory approved safety
shields that are in good repair.
13. Wear personal protective equipment such as, but not limited to, protection for eyes, ears, feet, hands
and head when operating or repairing the equipment. Do not wear loose clothing or jewelry that may
catch on equipment moving parts.
14. When performing adjustments or maintenance on the cutter, first lower it to the ground or block it
securely at a workable height.
15. Never stand between tractor and cutter while tractor is being backed to the cutter hitch.
16. Reduce speed when transporting cutter to avoid bouncing and momentary loss of steering.
17. Use tractor flashing warning lights, day or night, when transporting cutter on road or highways unless
prohibited by law.
18. It is recommended that tractor be equipped with Rollover Protective System (ROPS) and seat belt be
used in all mowing operations.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING
EMPLOYERS, EMPLOYEES AND OPERATIONS.
*(This section is intended to explain in broad terms the concept and effect of the following federal laws and
regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA
This Act Seeks:
“...to assure so far as possible every working man and woman in the nation safe and healthful working
conditions and to preserve our human resources...”
DUTIES
Sec. 5 (a) Each employer—
(1) shall furnish to each of his employees employment and a place of employment
which are free from recognized hazards that are causing or are likely to cause
death or serious physical harm to his employees;
(2) shall comply with occupational safety and health standards promulgated under
this Act.
(b) Each employee shall comply with occupational safety and health standards
and all rules, regulations and orders issued pursuant to this Act which are
applicable to his own actions and conduct.
OSHA Regulations
Current OSHA regulations state in part: “At the time of initial assignment and at least annually thereafter, the
employer shall instruct every employee in the safe operation and servicing of all equipment with which the
employee is, or will be involved.” These will include (but are not limited to) instructions to:
Keep all guards in place when the machine is in operation;
Permit no riders on equipment;
Stop engine, disconnect the power source, and wait for all machine movement to stop before
servicing, adjusting, cleaning or unclogging the equipment, except where the machine must be
running to be properly serviced or maintained, in which case the employer shall instruct employees
as to all steps and procedures which are necessary to safely service or maintain the equipment.
Make sure everyone is clear of machinery before starting the engine, engaging power, or operating
the machine.
EMPLOYEE TRACTOR OPERATING INSTRUCTIONS:
1. Securely fasten your seat belt if the tractor has a
ROPS.
5. Watch where you are going, especially at row
ends, on roads, and around trees.
2. Where possible, avoid operating the tractor near
ditches, embankments, and holes.
6. Do not permit others to ride.
7. Operate the tractor smoothly - no jerky turns,
starts, or stops.
3. Reduce speed when turning, crossing slopes, and
on rough, slick, or muddy surfaces.
8. Hitch only to the drawbar and hitch points recom-
mended by tractor manufacturers.
4. Stay off slopes too steep for safe operation.
9. When tractor is stopped, set brakes securely and
use park lock if available.
Child Labor Under 16 Years Old
Some regulations specify that no one under the age of 16 may operate power machinery. It is your
responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of
Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION I
INTRODUCTION AND DESCRIPTION
blades continue to cut the grass clippings several
1-1 INTRODUCTION
times before allowing the tiny pieces to fall to the
ground. This eliminates a build up of grass residue
on top of the lawn. The four caster wheel arrange-
ment, along with the floating lift linkage and the stan-
dard front and center rollers, all work together to give
an even cut and minimize scalping.
We are pleased to have you as a Bush Hog cus-
tomer. Your MP Series Rotary Cutter has been care-
fully designed to give maximum service with mini-
mum down time.This manual is provided to give you
the necessary operating and maintenance instruc-
tions for keeping your rotary cutter in top operating
condition. Please read this manual thoroughly.
Understand what each control is for and how to use
it. Observe all safety precautions decaled on the
machine and noted throughout the manual for safe
operation of implement. If any assistance or addi-
tional information is needed, contact your authorized
Bush Hog dealer.
Power from the tractor is transmitted through a trian-
gular, telescoping driveline to the 90 degree gear-
box. It is then passed to the spindle housings and
blades by two, B-section, Kevlar reinforced belts.
Drivetrain protection is provided by belt slippage.
Table 1-1 MTH Specifications
NOTE
MP 5
60
MP 6
72
All references made to right, left, top,
bottom, front or rear are as viewed
facing the direction of travel with
implement properly attached to trac-
tor.
Cutting Width (in.)
Cutting Height (in.)
Horsepower Range
Blade Tip Speed (fpm)
3/4 to 5-3/4
20-35
25-40
Top 17,600
Bottom 18,500
680 702
1-2 DESCRIPTION
The MP cutters (Figure 1-1) are grooming mowers
intended for cutting lawns, golf courses, athletic
fields, or any maintained area where a clean, uni-
form finish is desired. Three sets of counter-rotating
Weight (lbs.)
Figure 1-1 MP 5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION II
PREPARATION FOR USE
D. Hold driveline sections parallel to each other to
determine if too long. Each section should end
approximately 3 inches (76mm) short of reaching
universal joint shield on opposite section. If too
long, measure 3 inches (76mm) back from univer-
sal joint shield and mark opposite section. (Figure
2-1). Do this for both sections.
E. Raise and lower cutter to determine position
with greatest distance between PTO shaft and
gearbox input shaft. Shut down tractor leaving cut-
ter in position of greatest distance. SECURELY
BLOCK CUTTER IN POSITION.
2-1 ATTACHING TO TRACTOR
WARNING
NEVER STAND BETWEEN TRACTOR
AND CUTTER WHILE TRACTOR IS
BEING BACKED TO HITCH.
WARNING
ADDITIONAL
TRACTOR
FRONT
F. Hold down driveline sections parallel to each
other and check for minimum 6 inches (152mm)
overlap. (Figure 2-2) If driveline has been marked for
cutting, overlap will be the distance between two
marks. If driveline has less than minimum overlap,
DO NOT USE. Contact authorized Bush Hog dealer.
BALLAST MAY BE NEEDED FOR
STABLE OPERATION AND TRANSPORT
OF CUTTER. SEE TRACTOR OPERA-
TOR’S MANUAL FOR RECOMMENDED
WEIGHTS. IT IS RECOMMENDED THAT
TRACTOR BE EQUIPPED WITH
ROLLOVER PROTECTIVE SYSTEM
(ROPS) AND SEAT BELTS.
NOTE
If driveline is correct length, omit the fol-
lowing steps “G” through “J” and proceed
to step “K”.
A. Attach to tractor Cat. I three point hitch as
described in tractor operator’s manual.
Figure 2-1
NOTE
Due to the many variations in
tractor/implement hitch points and corre-
sponding differences in distances between
tractor PTO shafts and implement input
shafts, drivelines may need to be short-
ened as described in the following steps:
B. Raise and lower cutter to determine position
with shortest distance between the tractor PTO
shaft and gearbox input shaft. Shut down tractor
leaving cutter in position of shortest distance.
SECURELY BLOCK CUTTER IN POSITION.
C. Pull driveline apart. Attach outer (female) sec-
tion to tractor PTO shaft. Pull on driveline section to
be sure yoke locks into place.
Figure 2-2
Minimum
Overlap
8
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Clamp end of driveline in a vice. Cut off shield
where marked. (Figure 2-3).
Figure 2-5
Figure 2-3
DANGER
MAKE CERTAIN DRIVELINE YOKES
ARE SECURELY FASTENED. FAILURE
TO DO SO MAY RESULT IN SERIOUS
INJURY.
H. Using cut off section of shield as a guide, cut
shaft the same amount. (Figure 2-4)
Figure 2-4
L. Raise cutter off ground and adjust lower lift
arms to level cutter right to left. Refer to tractor oper-
ator’s manual.
M. Lower cutter to work position. Adjust tractor
top link to position cutter top link as shown in Figure
2-6. This allows cutter to “float” during operation.
N. Adjust tractor sway chains, stabilizer bar or
equivalent to prevent side sway.
Figure 2-6 Flex-Link
I. Repeat steps “G” and “H” to other driveline sec-
tion.
J. Deburr ends of driveline sections and clean
away all chips and filings. (Figure 2-5)
K. Apply multi-purpose grease to outside of male
driveline section. Assemble driveline and install on
tractor and cutter. Pull on each driveline section to
be sure yokes lock into place. Make certain driveline
shielding is in place and in good condition.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION III
OPERATING INSTRUCTIONS
FIGURE 3-1 Caster Wheel
3-1 GENERAL SAFETY
Only qualified people familiar with this operator’s
manual and tractor operator’s manual should oper-
ate this machine. Operator should wear hard hat,
safety glasses and safety shoes. The operator
should read, understand and practice all safety mes-
sages shown on the caution, warning and danger
decals affixed to the cutter to avoid serious injury or
death. It is recommended that tractor be equipped
with Rollover Protective System (ROPS) and a seat
belt be used. Before beginning operation, clear work
area of any objects that may be picked up and
thrown. Check for ditches, stumps, holes or other
obstacles that could upset tractor or damage cutter.
Always lower cutter to ground and allow blades to
come to a complete stop, set parking brake and turn
off tractor engine before leaving tractor operator’s
seat.
Spacers
Caster
Wheel
DANGER
STAY CLEAR OF ROTATING DRIVELINE. DO
NOT OPERATE WITHOUT DRIVELINE SHIELDS
IN PLACE AND IN GOOD CONDITION. FAILURE
TO HEED THESE WARNINGS MAY RESULT IN
PERSONAL INJURY OR DEATH.
3-2 CUTTING HEIGHT ADJUSTMENT
The cutter should be operated at the highest position
that will give desired cutting results. (See “TIPS” on
next page) This will help prevent blades from striking
the ground, reducing blade wear and undue strain on
the machine. Cutting too much material may reduce
mulching action and leave visible clippings on the lawn
surface. The more frequently the lawn is mowed, the
better the mulching effect will be. Adjust as follows:
DANGER
STAND CLEAR OF ROTATING CUTTER
BLADES UNTIL ALL MOTION HAS STOPPED.
TO AVOID ACCIDENTAL FALL AND POSSIBLE
INJURY FROM CUTTER,IT IS RECOMMENDED
THAT TRACTOR BE EQUIPPED WITH
ROLLOVER PROTECTIVE SYSTEM AND THAT A
SEAT BELT BE USED FOR ALL OPERATIONS.
A. Raise cutter off ground using tractor 3-point
lift. SECURELY BLOCK CUTTER IN POSITION.
shown in Figure 2-6.
C. With tractor at idle speed, engage PTO drive.
Advance throttle to 540 PTO rpm.
D. Place tractor in low gear and begin cutting.
Tractor forward speed should be controlled by gear
selection, not engine speed. For maximum cutting
efficiency, forward speed should allow cutter to
maintain a constant maximum blade speed.
WARNING
THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH
If tractor engine or cutter stalls, do not slip tractor
clutch to allow engine to retain speed as this will
exert undue strain on the implement drivetrain.
When stalling occurs, disengage PTO drive, move to
a cut area, set tractor throttle to idle, then re-engage
PTO drive.
B. Remove pin securing caster wheel to bracket.
(Figure 3-1) Remove caster wheel from arm.
C. Place amount of spacers on caster wheel to
give desired cutting height. With no spacers on the
bottom, a 3/4” cutting height is given.
D. Reinstall caster wheel into caster arm. Place
remaining spacers on caster wheel and install pin to
retain.
E. Repeat operation for all caster wheels. Make
certain all wheels are adjusted to the same height.
Always cut up and down the face of slopes, never
across.
Check belt tension after first 8 hours
3-3 OPERATION
3-4 TRANSPORTING
A. Perform BEFORE EACH USE maintenance
list in paragraph 4-1.
B. Start tractor. Lower cutter until it is supported
by caster wheels. Position tractor lower lift arms so
cutter lower links are parallel to ground, allowing cut-
ter to “float” during operation. Adjust top link as
Turn off PTO drive and fully raise tractor 3-point lift
before transporting. When implement is transported
on road or highway, day or night, use tractor flashing
warning lights unless prohibited by law. A slow mov-
ing vehicle (SMV) sign on the tractor must be visible
from the rear by approaching vehicles.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TIPS ON MOWING WITH A MULCHER
The Bush Hog MP 5/6 is a finishing mower with counter rotating blade sets designed to do a
superior job of mulching grass clippings. To get the maximum effectiveness from your MP
the tips listed below should be followed:
● Mow often - In general, mulching operations require more frequent mowing than would
conventional mowing procedures.
● Watch your speed - Normal conditions will allow a speed of up to approximately 5 mph,but
thick, heavy, damp conditions will require reduced ground speed.
● Mow at 540 RPM to keep tip speed at its maximum.
● Mow with a clean mower - Avoid grassy build-up under the deck.
● Mow with sharp blades - A sharp blade cuts cleaner.
● Wet grass will decrease distribution effectiveness and increase horsepower require-
ments. Leaves, on the other hand, may be more effectively mulched when they are
slightly damp.
● Mow at higher cutting heights - Remove and mulch no more than 2” - 2-1/2” of grass
length with each mowing. (Experts recommend not cutting off more than 1/3 of the
grass blade length at any given time.)
● Mow twice, at different height settings, (high, then low), if grass is extra tall.
● Keep your lawn clean, healthy and fertilized.
Figure 3-2 Sharp blades and a clean mower enhance mowing performance.
NOTE:
The MP 5/6 mulching mowers are equipped with
adjustable, removable baffles on the rear sides of the
outer blades. These baffles are factory installed in
the intermediate position for the most common grass
conditions. If extra fine mulching in light cutting con-
ditions is desired, the baffles may be installed in the
lower position. When heavy cutting conditions exist,
the baffles may be completely removed to prevent a
grass build-up from occurring.
Removable Baffles
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION IV
MAINTENANCE
8.During operation, listen for abnormal sounds
4-1 MAINTENANCE CHECK LIST
which might indicate loose parts, damaged bearings,
or other damage. Correct any deficiency before con-
tinuing operation.
Perform scheduled maintenance as outlined below.
Lower implement to ground, turn off tractor, and set
parking brake before doing maintenance inspections
or work. Some checks may require raising machine
off ground and supporting with blocks. All bolts
should be torqued as indicated in torque chart
unless otherwise indicated.
AFTER EACH USE
1. Clean all debris from machine especially under-
side of deck, underneath belt shield and off safety
decals. Replace any missing or illegible decals.
2. Inspect cutter for worn or damaged compo-
nents. Repair or replace before next use. Any
replacement components installed during repair shall
include the components’ current safety decals speci-
WARNING
THE CUTTER CAN FALL FROM
HYDRAULIC SYSTEM FAILURE. TO
AVOID SERIOUS INJURY OR DEATH,
SECURELY SUPPORT CUTTER BEFORE
WORKING UNDERNEATH.
fied by the manufacturer to be affixed to the compo-
nent.
3. Store cutter in a dry place.
40 HOURS
1. Check belts for proper tension. Refer to para-
graph 4-3.
BEFORE EACH USE.
1. Check tractor tire air pressure. Refer to
tractor operator’s manual. Check mower tire pres-
sure. Tire pressure should be 30 psi.
2. Check blades and spindles to be sure that no
foreign objects such as wire or steel strapping bands
are wrapped around them.
4-2 LUBRICATION (Figures 4-1A, & B)
NOTE
The multi-purpose grease referenced in this
secftion is an NLGI Grade 2 type grease.
3. Check blade bolts for tightness. Tighten bottom
blade bolt to 76 ft./lbs., top blade bolts to 31 ft./lbs.
4. Inspect blades for wear. Replace if necessary
per paragraph 4-5. Use only genuine Bush Hog
replacement parts. If it is necessary to sharpen the
blades, remove the blades from the spindles before
sharpening. DO NOT sharpen blades while still
attached to mower.
5. Make certain all shields are in place and in
good condition. Repair or replace any missing or
damaged shields.
6. Inspect wheel(s) for wear, damage or foreign
objects. Repair or replace if necessary.
BEFORE EACH USE
1. Driveline Universal Joints - Apply multi-purpose
grease with grease gun.
2. Driveline Guard - Apply 2-3 shots of multi-pur-
pose grease with grease gun to plastic fitting.
3. Wheels - Apply multi-purpose grease wiith
grease gun.
4. Caster Pivot - Apply multi-purpose grease with
grease gun.
20 HOURS
5. Driveline - Disconnect PTO driveline, pull the
two sections apart, thoroughly clean old grease from
tubes and apply thin coat of multi-purpose grease to
outside of inner (male) section. Reassemble sec-
tions and install. Pull each section to be sure drive-
line and shields are securely connected. Make cer-
tain PTO shielding is in good condition.
7. Perform BEFORE EACH USE lubrication per
paragraph 4-2.
Figure 4-1A
40 HOURS
6. Input Gearbox - Add EP80W-90 gear oil, if
necessary, to bring oil level to check plug.
(6) 40 Hours
(5) 20 Hours
Figure 4-1B
(4)
(2) Before Each Use
(1) Before Each Use
(3)
Before Each Use
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4-3 BELT ADJUSTMENT
4-4 BELT REPLACEMENT
Belt tensions should be checked every 40 hours to
get maximum life from drive belts and best perfor-
mance from the cutter. Belt tension is adjusted by
increasing or decreasing the length of the spring on
the moveable idlers. For proper belt tension on the
mower, the spring lengths should be set at 2-7/8”.
(Figure 4-2) To adjust the spring length, loosen or tight-
en the 3/8” hex nuts on the spring adjustment rod until
the correct spring length is reached.
Use only genuine Bush Hog replacement parts. It is
not necessary to replace both belts if only one is
worn.
A. Remove right and left side shields.
B. Relieve spring tension by loosening the two
3/8” hex nuts on each spring adjustment rod. (Figure
4-2)
C. Remove old belts.
D. Install new belts as shown below. (Also refer
to the decal on underside of belt shield)
Figure 4-2 3/8” Hex Nuts - Spring Length Adjustment
1. Belts must be installed at the same time. One
belt cannot be installed and tightened down before
the other.
2. Disconnect the upper adjustment rod from the
upper idler assembly.
3. Place both belts into the respective grooves
on the driving sheave.
4. Work the lower belt over the other sheaves.
After the lower belt is in place, complete the installa-
tion of the upper belt.
5. Connect the upper adjustment rod and the
upper idler assembly.
6. Tighten the compression springs on the upper
and lower drives to 2-7/8” long. Tighten the jam nuts
on the adjustment rods.
7. Replace all shields before operating machine.
Figure 4-3
Upper Idler Assembly
UPPER BELT DIAGRAM
Upper Adjustment Rod
Driving Sheave
At Gearbox
LOWER BELT DIAGRAM
Driving Sheave
At Gearbox
Lower Adjustment Rod
13
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Remove the 3/8” - 24UNF x 7/8” Gr. 8 blade-
bolt and nut for each blade. Inspect the blade nut
shoulder and the blade bolts for wear. Replace if
necessary.
F. When installing new blades on the mulching
assembly, make sure that two blades are installed
on the top side of the assembly 180° from each
other and two on the bottom side of the assembly.
The blades must mount on the rotation “pads” for
proper operation. Assemble the (4) new blades to
the blade holder using the blade nuts, bolts, and flat-
wahsers. Tighten the bolts to 45 ft./lbs. Strike the
blade nut with a heavy hammer to seat, then tighten
again.
G. Insert the blade bushing in the center of the
mulching assembly so that the bushing flange is on
the top side of the assembly. Slide the mulching
assembly and flanged bushing over the spindle shaft
and secure mulching assembly to the upper blade
carrier using the (4) 3/8” - 16UNC x 3/4 Gr. 5 bolts
and belleville washers. Torque all (4) mulching
assembly attaching bolts to 31 ft./lbs.
H. Install the blade washer over the spindle
shaft. Install the bottom blade and torque the 1/2” -
20UNF Gr. 8 bolt to 76 ft./lbs. Note: The concave
side of the belleville washer must be toward the
blades. Do not substitute with a flat washer.
4-5 BLADE REPLACEMENT
CAUTION
WEAR HEAVY WORK GLOVES TO PRO-
TECT HANDS FROM SHARP EDGES.
WHEN TURNING BLADES, BE AWARE OF
OPPOSITE BLADE APPROACHING.
Always replace all (4) blades on an assembly to
retain balance. In addition to replacing blades when
they become worn and dull, they should also be
replaced if the uplift angle on the trailing side of the
blade becomes worn off. As the angle wears down,
the mulching action deteriorates.
A. Raise cutter using tractor hydraulic system
and use transport locks before changing blades.
B. Turn off tractor,set parking brake and remove
key.
C. Remove bolt and Belleville washer securing
bottom blade to spindle. Remove blade. Shaft wash-
er will come off with the blade. (Figure 4-4)
D. Remove the four 3/8” x 1” capscrews and
belleville washers from the upper mulching assembly.
Remove mulching assembly. The blade bushing will
come off with the mulching assembly.
Figure 4-4 MP6 Blade Arrangement
3/8” - 24UNF x 7/8” Gr. 8 Blade Bolt & Blade Nut
3/8” x 1” Capscrew &
Belleville Washer
Rotation Pad
Upper Blade Assembly
Bottom Blade Bolt &
Belleville Washer
Shaft Washer
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-5 Blade And Spindle Assembly
4-6 BLADE SPINDLE SERVICE (Figure 4-5)
Nut for Inner Shaft
Flat Washer
If shaft bearings or other parts require replacement,
proceed as follows:
Drive Sheave for Inner Shaft
NOTE
It is recommended that a Bush Hog dealer or other
qualified person service the blade spindle. If blade
spindles must be disassembled, special Bush Hog
spanner wrenches are supplied for this operation. The
Sheave Wrench is used on the outer shaft drive
sheave. The Shaft Wrench is used in the notches on
either end of the outer shaft. These wrenches are
stored in the tool box on the frame.
Drive Sheave for Outer Shaft
Upper Bearing for Inner Shaft
Woodruff Key
Inner Shaft
Shaft Wrench
A. Wearing heavy gloves to protect hands,
remove blades from spindle, belts from sheaves and
remove complete spindle assembly from deck.
B. Remove lock nut above sheave on end of of inner
shaft.
Upper Bearing for Outer Shaft
Sheave Wrench
Outer Shaft
C. Remove drive sheave from inner shaft. (A gear
puller may be required for this operation.) Remove the
woodruff key from the inner shaft.
Hub
D. Support the assembly on the blade carrier and
press the inner shaft and lower inner bearing out.
E. To remove the bearing from the shaft, support the
inner bearing race and press shaft out.
F. Press upper inner bearing out of the assembly.
G. Unstake sheave from upper end of outer shaft
and unstake blade carrier from lower end of outer shaft
using a blunt punch or chisel. (Use care so as not to
damage threads.) Clamp the blade carrier into a vise and
remove the drive sheave using the sheave wrench
(95778). These threads are left handed - to loosen,
turn clockwise!
Lower Bearing for Outer Shaft
Lower Bearing for Inner Shaft
Blade Carrier
Blade Bushing
Blade Nut
Bolt
Flatwasher
Upper Blade Disc
NOTE: If your vise is not large enough to clamp the
blade carrier, reinstall the blade onto the carrier. Tighten
the bolts only “finger tight”. The blade may then be
clamped in the vise. Also notice that it makes no differ-
ence if the blade carrier loosens first. If the blade carrier
comes off first, remove it from the vise and clamp the
sheave wrench into the vise with “pins” pointing upward.
Turn assembly upside down and place sheave onto
“pins”. The shaft wrench may then be used on the oppo-
site end of the shaft to unscrew it from the sheave.
These threads are left handed - to loosen, turn clock-
wise.
H. Support the housing and press the outer shaft and
lower bearing out.
I. Press the upper bearing out of the housing.
J. Support the lower bearing and press the outer
shaft out.
Upper Blade
Blade Nut
Belleville Washer &
Bolt
Shaft Washer
Lower Blade
Belleville Washer &
Bolt
C. Thread the outer shaft sheave and blade car-
rier onto the assembly. These threads are left
handed - to tighten, turn counter-clockwise.
Clamp the blade carrier in a vise and insert the
sheave wrench pins into the outer drive sheave.
Using a torque wrench in conjunction with the
sheave wrench, tighten the assembly to 200 ft./lbs.
Refer to Fig. 4-6 on following page for the required
torque for your specific torque wrench.
D. Restake the blade carrier and drive sheave
into the notches of the outer shaft.
E. Install the woodruff key, sheave, flat washer
and nut onto the inner shaft and torque the nut to 76
ft./lbs.
F. Place the blade bushing onto the inner shaft
with the ring side toward the bearing (Fig. 4-5)
Install the upper blade disc with bolts and belleville
washers onto the blade carrier.Torque to 31 ft./lbs.
G. Install the shaft washer, lower blade belleville
washer and blade bolt onto the inner shaft and
torque the blade bolt to 76 ft./lbs.
BLADE SPINDLE REASSEMBLY
A. Install the inner shaft into the outer shaft by press-
ing upper and lower inner bearings into place. Press on
the inner and outer race of the bearings simultaneously
until the bearings bottom out on the shoulder of the inner
shaft.
B. Install the outer shaft sub-assembly into the hous-
ing by pressing the upper and lower outer bearings into
place. Press on the inner and outer race of the bearings
simultaneously until the bearings bottom out on the
shoulder of the outer shaft.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4-6 Torque Wrench Operation
A
6”
TORQUE WRENCH CHART
When using a torque wrench in conjunction with a Bush Hog shaft or sheave wrench,
the following chart must be used to achieve the correct torque of 200 ft./lbs.
Torque Wrench
Length (A)
12”
14”
16”
18”
20”
22”
Torque Indicator
Must Show
133
ft./lbs.
140
ft./lbs.
145
ft./lbs.
150
ft./lbs.
154
ft./lbs.
157
ft./lbs.
4-7 TROUBLESHOOTING
Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts
are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model num-
ber, serial number, purchase date and exact cause or description of problem.
Table 4-1 Troubleshooting
PROBLEM
PROBABLE CAUSE
REMEDY
Uneven Cut
Cutter not level side to side
or front to rear.
See SECTION III.
Belt slipping.
Adjust belt per paragraph 4-3.
Replace blade(s).
Worn or bent blade(s).
Streaking or Windrowing
Possible build-up of
material under cutter.
Clean cutter.
Cutter not level.
Worn blades.
See SECTION III.
Replace blades.
Belt slipping.
Adjust belt per paragraph 4-3.
Check all bolts for tightness.
Check oil per paragraph 4-2.
Noisy Cutter
Loose components.
Low oil in gearbox.
Rapid Blade Wear
(cutting edge)
Blade contacting
ground.
Adjust cutting height to
eliminate ground contact.
Rapid Blade
Wear
Cutter not being
operated at rated PTO speed.
Set tractor throttle for
proper PTO speed.
Use lower gear.
Cutter Vibrating
Cutter not being operated
at rated PTO speed.
Set tractor throttle for
proper PTO speed.
Blade(s) bent.
Replace blades.
Remove object.
Foreign object wrapped
around spindle or blade.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION V
DEALER ASSEMBLY
AFTER COMPLETING ANY ASSEMBLY STEP,
CAUTION
THOROUGHLY READ THE NEXT STEP IN THE
ASSEMBLY INSTRUCTIONS BEFORE PRO-
CEEDING WITH THAT STEP.
THE FOLLOWING SAFETY PRECAUTIONS
SHOULD BE THOROUGHLY UNDERSTOOD
BEFORE ATTEMPTING MACHINE ASSEMBLY.
11. After completing assembly, thoroughly inspect
the machine to be sure that all nuts, bolts, hydraulic
fittings or any other fastened assemblies have been
thoroughly tightened.
12. After completing assembly, be sure that all
safety locking devices or guards are in place.
13. Before operating the machine, thoroughly
read the operation section of this manual.
14. Before operating the machine, read the main-
tenance section of this manual to be sure that any
parts requiring lubrication such as gearboxes are full
to avoid any possible damage.
1. Wear personal protective equipment such as,
but not limited to, protection for eyes, ears, feet,
hands, lungs and head when assembling the equip-
ment. Do not wear loose clothing or jewelry that may
catch on equipment moving parts.
2. Do not lift heavy parts or assemblies. Use
crane, jack, tackle, fork trucks or other mechanical
devices.
3. Select an area for assembly that is clean and
free of any debris which might cause persons work-
ing on the assembly to trip.
4. Arrange parts to be assembled neatly in the
work area and have tools or other mechanical assist-
ing devices in easy reach.
5. Inspect all parts and assemblies thoroughly and
remove any sharp edges, grease, oil or dirt which-
might cause pieces to slip when handling.
6. Preview the assembly instructions in your oper-
ator’s manual before proceeding further.
7. If the assembly instructions call for parts or
assemblies to be blocked up, use only blocking
material that is in good condition and is capable of
handling the weight of the assembly to be blocked.
Also, insure that the blocking material is on a clean,
dry surface.
8. Never put hands or any other part of body
under blocked up assemblies if at all possible.
9. Always wear goggles or safety glasses when
hammering, grinding, or drilling metal parts.
10. If the assembly calls for welding or cutting, be
sure that there are no flammable materials close at
hand and that bystanders have taken necessary pre-
cautions.
BEFORE OPERATING THE EQUIPMENT, IF YOU
HAVE ANY QUESTIONS REGARDING THE
PROPER ASSEMBLY OR OPERATION, CON-
TACT YOUR AUTHORIZED BUSH HOG DEALER
OR REPRESENTATIVE.
5-1 BASE UNIT ASSEMBLY
A. Attach lower lift links to deck assembly using
5/8 x 2-1/2 bolts, flatwashers, lockwashers, hex nuts
and pivot bushings. (Figure 5-1)
B. Install lift pins onto lower links, securing with
7/8” lockwashers and hex nuts.
C. Attach mast halves to deck assembly using 1/2
x 1-1/2” bolts, lockwashers and hex nuts.
D. Loosely attach two caster arms to the front of
the mower deck using 5/8 x 3-1/2” bolts, l;ockwash-
ers and hex nuts. Loosely attach the remaining two
caster arms to the rear of the mower deck using 5/8
x 3-1/2” bolts, lockwashers and hex nuts in each
caster arm. Attach mast supports to lugs at the rear
of the mower deck using 1/2 x 1-1/4” bolts, lock-
washers and hex nuts.
Flex Link
Figure 5-1
Mast
Support
Mast Half
Gearbox
Caster Arm
Spacers
Lower Link
17
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Install front roller by securing the right and left
roller mounts to the deck in the holes provided by
using 3/8 x 1” carriage bolts, flatwashers and lock-
washers. (Figure 5-2) Assemble roller, roller shaft,
retaining pin and roll pin as shown.
H. Fill gearbox with EP80W-90 gear oil until oil
level is at check plug on side of gearbox housing.
Allow time for oil to seep through bearings into lower
housing. (Capacity is 1 quart) Replace solid fill plug
with breather plug supplied in operator’s manual
package.
E. Fasten mast supports and upper flex link to
mast halves using 1/2 x 5” bolt,pivot tube and locknut.
F. Place one long spacer on the caster stems
and insert into caster arms. Place three long spacers
and two short spacers on the caster stem above the
caster arms. this arrangement will give a cutting
height of approximately 1-3/4” . Secure with lynch
pin retainers. With weight of cutter resting on all four
wheels, ensure that cutter is level. Tighten all bolts
on mounting brackets.
Figure 5-2 Front Roller
3/8 x 1” Bolt, Lockwasher
and Flatwasher
Roller Mounts
Retaining Pin
Roller Shaft
Roller
Roll Pin
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECALS
To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage
can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide
safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for
more information.
82619
78608
50012615
82617
82618
60873
50012616
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TORQUE SPECIFICATIONS
Proper toque for American fasteners used on Bush Hog equipment.
Recommended Torque in Foot Pounds (Newton Meters).*
AMERICAN
BOLT DIAMETER
Bolt Head Markings
WRENCH
SIZE (IN.) “A”
(IN.) “B” AND
THREAD SIZE
SAE
GRADE 2
SAE
GRADE 5
SAE
GRADE 8
7/16
7/16
1/4 - 2O UNC
1/4 - 28 UNF
5/16 - 18 UNC
5/16 - 24 UNF
3/8 - 16 UNC
3/8 - 24 UNF
7/16 - 14 UNC
7/16 - 20 UNF
1/2 - 13 UNC
1/2 - 20 UNF
9/16 - 12 UNC
9/16 - 18 UNF
5/8 - 11 UNC
5/8 - 18 UNF
3/4 - 10 UNC
3/4 - 16 UNF
7/8 - 9 UNC
6 (7)
8 (11)
10 (13)
12 (16)
14 (18)
6 (8)
1/2
11 (15)
17 (23)
25 (33)
SAE Grade 2
(No Dashes)
1/2
13 (17)
19 (26)
27 (37)
9/16
20 (27)
31 (42)
44 (60)
9/16
23 (31)
35 (47)
49 (66)
5/8
32 (43)
49 (66)
70 (95)
5/8
36 (49)
55 (75)
78 (106)
3/4
49 (66)
76 (103)
106 (144)
120 (163)
153 (207)
172 (233)
212 (287)
240 (325)
376 (509)
420 (569)
606 (821)
668 (905)
909 (1232)
995 (1348)
1019 (1381)
1288(1745)
1444 (1957)
1817 (2462)
2013 (2728)
2382 (3228)
2712 (3675)
3161 (4283)
3557 (4820)
3/4
55 (75)
85 (115)
7/8
70 (95)
109 (148)
122 (165)
150 (203)
170 (230)
266 (360)
297 (402)
430 (583)
474 (642)
644 (873)
705 (955)
721 (977)
795 (1077)
890 (1206)
1120 (1518)
1241 (1682)
1470 (1992)
1672 (2266)
1950 (2642)
2194 (2973)
7/8
79 (107)
97 (131)
110 (149)
144 (195)
192 (260)
166 (225)
184 (249)
250 (339)
274 (371)
280 (379)
354 (480)
397 (538)
500 (678)
553 (749)
655 (887)
746 (1011)
870 (1179)
979 (1327)
SAE Grade 5
(3 Dashes)
15/16
15/16
1-1/8
1-1/8
1-5/16
1-5/16
1-1/2
1-1/2
1-1/2
1-11/16
1-11/16
1-7/8
1-7/8
2-1/16
2-1/16
2-1/4
2-1/4
7/8 - 14 UNF
1 - 8 UNC
1 - 12 UNF
Wrench
Size “A”
SAE Grade 8
(6 Dashes)
1 - 14 UNF
1-1/8 - 7 UNC
1-1/8 - 12 UNF
1-1/4 - 7 UNC
1-1/4 - 12 UNF
1-3/8 - 6 UNC
1-3/8 - 12 UNF
1-1/2 - 6 UNC
1-1/2 - 12 UNF
Proper torque for metric fasteners used on Bush Hog equipment.
Recommended torque in foot pounds (newton Meters).*
METRIC
WRENCH
SIZE
BOLT
DIA.
ASTM
4.6
ASTM
8.8
ASTM
9.8
ASTM
10.9
(mm) “A”
(mm) “B”
8
5
1.8 (2.4)
3 (4)
5.1 (6.9)
8.7 (12)
21.1 (29)
42 (57)
6.5 (8.8)
11.1 (15)
27 (37)
10
13
16
18
21
24
30
33
36
41
46
6
8
7.3 (10)
14.5 (20)
25 (34)
40 (54)
62 (84)
122 (165)
Wrench
Size “A”
10
12
14
16
20
22
24
27
30
53 (72)
8.8
74 (100)
118 (160)
167 (226)
325 (440)
443 (600)
563 (763)
821 (1112)
1119 (1516)
73 (99)
93 (126)
116 (157)
181 (245)
148 (201)
230 (312)
449 (608)
611 (828)
778 (1054)
1138 (1542)
1547 (2096)
Numbers appearing on bolt heads
indicate ASTM class.
*Use 75% of the specified torque value for plated
fasteners. Use 85% of the specificed torque
values for lubricated fasteners.
211 (286)
418 (566)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
P.O. Box 1039
l
Selma, AL 36702-1039
Telephone (334) 874-2700
l
Download from Www.Somanuals.com. All Manuals Search And Download.
|