Brother Sewing Machine XL5050NTC User Manual

Winding the bobbin. (Your machine may be supplied with a fully wound  
Step 3  
bobbin, but you may want to fill another bobbin with your own thread.)  
figure 3a  
GETTING STARTED:  
XL series Sewing Machines  
Set the power switch to on (I).  
Place a spool of thread on the spool pin (figure 3a).  
tension  
disk  
XL5050NTC  
XL5060NTC  
XL5070NTC  
Unwind some thread and pass the thread around the  
tension disk.  
To help you get started, please follow these simple instructions in the order shown below.  
However, before you do so, read the safety instructions in the Instruction Manual.  
Take one of the bobbins from the accessory pack.  
Pass the thread through the hole in the bobbin from  
Unpack the sewing machine, and familiarise yourself with all the parts  
and controls that are mentioned in these instructions.  
the inside.  
Step 1  
Clip the bobbin onto the bobbin winding shaft.  
Push the bobbin winding shaft firmly to the right until  
it clicks into place against the stop (figure 3b).  
Tension  
Dial  
Spool Pin  
Balance  
Wheel  
Figure 1a  
Figure 1b  
Bobbin Winding  
Shaft  
Tension Disk and  
Thread Guide  
Hold the end of the thread and press the foot controller  
to wind the thread around the bobbin a few times.  
figure 3b  
figure 3d  
figure 3c  
Take-up  
Lever  
Guide  
Trim the excess thread (figure 3c), and continue  
winding until the winding shaft stops automatically.  
Pattern  
Dial  
Power  
Switch  
Push the bobbin winding shaft back to the left, cut the  
thread, and remove the bobbin from the shaft (figure 3d).  
Stitch  
Length  
Dial  
Thread  
Cutter  
Mains  
Plug  
Unwind the thread from the tension disk.  
Reverse  
Lever  
Presser Foot and  
Needle Assembly  
Presser Foot  
Lever  
Lower threading. (Your machine may be supplied with a threaded bobbin,  
but you may want to use another bobbin with your own thread.)  
Foot  
Controller  
Connection  
Step 4  
Extension Table  
(accessories and  
bobbins inside)  
Set the power switch to off (O).  
Foot  
Controller  
Raise the needle to its highest position by turning the balance wheel towards you (counter-clockwise).  
Open the shuttle cover behind the extension table.  
figure 4b  
figure 4a  
Bobbin and  
Bobbin Case  
Remove the bobbin case from the shuttle, by pulling  
the latch (marked in red on figure 4a).  
Using the fingerhold on the left-hand side, pull firmly  
upwards and forwards to remove the extension table.  
latch  
Leaving about 10 cm (4 in) of thread trailing, insert  
the bobbin into the bobbin case (figure 4b).  
Inside the extension table is the storage compartment.  
Open the storage compartment with a sharp tug, to  
find various accessories and a number of bobbins.  
Shuttle  
Cover  
figure 4c  
figure 4d  
spring  
Hold the bobbin case in your left hand with the  
bobbin case finger pointing towards you (figure 4c).  
bobbin  
case  
finger  
slot  
With your right hand, pull the trailing thread into the  
slot in the bobbin case (figure 4c).  
Prepare the sewing machine for use.  
Step 2  
Draw the thread down under the spring into the  
delivery eye (figure 4d).  
delivery  
eye  
figure 4e  
• Plug in the foot controller connector at the right hand side of the machine, as shown in figure 1a. Connect the  
mains plug into a wall socket, and place the controller on the floor.  
Hold the bobbin case by the latch, with the finger  
pointing upwards (figure 4e).  
Grip the top of the spool pin, and pull it upwards as shown in figure 1b until it clicks into place at a height of  
about 50 mm (2 in). Be careful not to pull the pin off the machine.  
Insert the bobbin back into the shuttle, release the  
latch, and push the bobbin in until it clicks.  
Set the tension dial to 5.  
Make sure the bobbin case goes in all the way, or the  
latch will not hold the bobbin properly.  
Set the pattern dial to straight stitch.  
Set the stitch length dial to between 2 and 3.  
Leave the shuttle cover open.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Server 5000HQ User Manual
Black Box Network Hardware LWE100A User Manual
Black Decker Vacuum Cleaner 90521333 User Manual
Bolens Log Splitter 248 645A User Manual
Breville Kitchen Grill BGR400XL User Manual
Briggs Stratton Power Supply 18000 User Manual
Brinkmann Charcoal Grill 810 3810 S User Manual
Britax Car Seat Roundabout User Manual
Chauvet Baby Accessories LED PAR 56 24UVB User Manual
Chevrolet Automobile 2010 Impala User Manual