SERVICE MANUAL
KE-430F
BE-438F
Please read this manual before making any adjustments.
ELECTRONIC DIRECT DRIVE LOCKSTITCH BAR TACKER
ELECTRONIC DIRECT DRIVE LOCKSTITCH BUTTON SEWER
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
[1] Safety indications and their meanings
This service manual and the indications and symbols that are used on the machine itself are provided in order to ensure
safe operation of this machine and to prevent accidents and injury to yourself or other people.
The meanings of these indications and symbols are given below.
Indications
The instructions which follow this term indicate situations where failure to follow the
instructions will result in death or serious injury.
DANGER
The instructions which follow this term indicate situations where failure to follow the
instructions could result in death or serious injury.
WARNING
The instructions which follow this term indicate situations where failure to follow the
instructions may result in minor or moderate injury.
CAUTION
Symbols
This symbol ( ) indicates something that you should be careful of. The picture inside the triangle
indicates the nature of the caution that must be taken.
(For example, the symbol at left means “beware of injury”.)
･･････
This symbol ( ) indicates something that you must not do.
･･････
This symbol ( ) indicates something that you must do. The picture inside the circle indicates the
nature of the thing that must be done.
･･････
(For example, the symbol at left means “you must make the ground connection”.)
KE-430F, BE-438F
i
Download from Www.Somanuals.com. All Manuals Search And Download.
[2] Notes on safety
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
before opening the face plate of the control box. Touching areas where high voltages are present will result in
serious injury from electric shocks.
WARNING
Do not allow any liquids to get onto this sewing machine, otherwise fire, electric shocks or operating problems could
occur.
If any liquid gets inside the sewing machine (machine head or control box), immediately turn off the power and
disconnect the power plug from the electrical outlet, and then contact the place of purchase or a qualified
technician.
CAUTION
Environmental requirements
Use the sewing machine in an area which is free from
sources of strong electrical noise such as electrical
line noise or static electric noise.
Sources of strong electrical noise may cause
problems with correct operation.
The ambient temperature should be within the range
of 5°C to 35°C during use.
Temperatures which are lower or higher than this
may cause problems with correct operation.
The relative humidity should be within the range of
45% to 85% during use, and no dew formation should
occur in any devices.
Excessively dry or humid environments and dew
formation may cause problems with correct operation.
Any fluctuations in the power supply voltage should
be within ±10% of the rated voltage for the machine.
Voltage fluctuations which are greater than this may
cause problems with correct operation.
The power supply capacity should be greater than the
requirements for the sewing machine’s power
consumption.
In the event of an electrical storm, turn off the power
and disconnect the power cord from the wall outlet.
Lightning may cause problems with correct operation.
Insufficient power supply capacity may cause
problems with correct operation.
Installation
Machine installation should only be carried out by a
qualified technician.
All cords should be secured at least 25 mm away
from any moving parts. Furthermore, do not
excessively bend the cords or secure them too firmly
with staples, otherwise there is the danger that fire or
electric shocks may occur.
Contact your Brother dealer or a qualified electrician
for any electrical work that may need to be done.
The sewing machine weighs approximately 57 kg.
The installation should be carried out by two or more
people.
Install the safety covers to the machine head and
motor.
If using a work table which has casters, the casters
should be secured in such a way so that they cannot
move.
Do not connect the power cord until installation is
complete, otherwise the machine may operate if the
foot switch is depressed by mistake, which may result
in injury.
Be sure to wear protective goggles and gloves when
handling the lubricating oil and grease, so that they
do not get into your eyes or onto your skin, otherwise
inflammation can result.
Furthermore, do not drink the oil or eat the grease
under any circumstances, as they can cause vomiting
and diarrhoea.
Hold the machine head with both hands when tilting it
back or returning it to its original position.
Furthermore, after tilting back the machine head, do
not push the face plate side or the pulley side from
above, as this may cause the machine head to topple
over, which may result in personal injury or damage
to the machine.
Keep the oil out of the reach of children.
Be sure to connect the ground. If the ground
connection is not secure, you run a high risk of
receiving a serious electric shock, and problems with
correct operation may also occur.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
CAUTION
Sewing
This sewing machine should only be used by
operators who have received the necessary training
in safe use beforehand.
If using a work table which has casters, the casters
should be secured in such a way so that they cannot
move.
The sewing machine should not be used for any
applications other than sewing.
Attach all safety devices before using the sewing
machine. If the machine is used without these
devices attached, injury may result.
Be sure to wear protective goggles when using the
machine.
If goggles are not worn, there is the danger that if a
needle breaks, parts of the broken needle may enter
your eyes and injury may result.
Do not touch any of the moving parts or press any
objects against the machine while sewing, as this
may result in personal injury or damage to the
machine.
Turn off the power switch at the following times,
otherwise the machine may operate if the foot switch
is depressed by mistake, which may result in injury.
If an error occurs in machine operation, or if abnormal
noises or smells are noticed, immediately turn off the
power switch. Then contact your nearest Brother
dealer or a qualified technician.
• When replacing the needle and bobbin
• When not using the machine and when leaving the
machine unattended
If the machine develops a problem, contact your
nearest Brother dealer or a qualified technician.
Use threading mode or turn off the power first in order
to carry out threading.
Cleaning
Turn off the power switch before carrying out
cleaning, otherwise the machine may operate if the
foot switch is depressed by mistake, which may result
in injury.
Be sure to wear protective goggles and gloves when
handling the lubricating oil and grease, so that they
do not get into your eyes or onto your skin, otherwise
inflammation can result.
Furthermore, do not drink the oil or eat the grease
under any circumstances, as they can cause vomiting
and diarrhoea.
Keep the oil out of the reach of children.
Maintenance and inspection
Maintenance and inspection of the sewing machine
should only be carried out by a qualified technician.
Hold the machine head with both hands when tilting it
back or returning it to its original position.
Furthermore, after tilting back the machine head, do
not push the face plate side or the pulley side from
above, as this could cause the machine head to
topple over, which may result in personal injury or
damage to the machine.
Ask your Brother dealer or a qualified electrician to
carry out any maintenance and inspection of the
electrical system.
Turn off the power switch and disconnect the power
cord from the wall outlet at the following times,
otherwise the machine may operate if the foot switch
is depressed by mistake, which may result in injury.
When replacing parts and installing optional
accessories, be sure to use only genuine Brother
parts.
Brother will not be held responsible for any accidents
or problems resulting from the use of non-genuine
parts.
• When carrying out inspection, adjustment and
maintenance
• When replacing consumable parts such as the
rotary hook
If any safety devices have been removed, be
absolutely sure to re-install them to their original
positions and check that they operate correctly before
using the machine.
If the power switch needs to be left on when carrying
out some adjustment, be extremely careful to observe
all safety precautions.
To prevent accidents and problems, do not modify
the machine yourself.
Brother will not be held responsible for any accidents
or problems resulting from modifications made to the
machine.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
[3] Warning labels
The following warning labels appear on the sewing machine.
Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are
difficult to read, please contact your nearest Brother dealer.
1
Touching areas where high voltages are present can result in severe injury.
Turn off the power before removing the cover.
2
*Safety devices
3
Eye guard
Finger guard
Solenoid cover
Thread take-up cover
Side cover
Rear cover, etc.
Be sure to connect the ground. If
the ground connection is not
6
secure, you run a high risk of
receiving a serious electric shock,
and
problems
with
correct
operation may also occur.
Direction of operation
7
8
Be careful to avoid injury from the moving thread
take-up.
Do not hold, otherwise
problems with
4
5
operation or injury may
occur.
Be careful not to get your hands caught when
returning the machine head to its original position
after it has been tilted.
9
KE-430F, BE-438F
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Thread take-up cover
Eye guard
Finger guard
2520B
2522B
Rear cover
Solenoid cover
Side cover
Transformer box
(100V/400V system only)
Oil tank
2521B
2559B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
v
CONTENTS
1. SPECIFICATIONS ............................... 1
2. NOTES ON HANDLING........................ 2
7. USING SD CARDS...............................43
7-1. Notes on handling SD cards
(commercially available) ...................................... 43
3. RELATIONSHIP BETWEEN
7-2. Structure of an SD card folder ............................. 43
7-3. Preparation for reading and writing data.............. 44
PROGRAMS AND PATTERNS ........... 3
4. FUNCTION SETTINGS......................... 6
7-4. Reading additional pattern data........................... 45
7-5. Writing additional pattern data to an SD card ...... 46
7-6. Reading memory switch data .............................. 47
4-1. List of special functions when power is
turned on.............................................................. 6
4-2. List of advanced functions ................................... 8
4-3. Setting memory switches (Advanced).................. 9
4-4. List of memory switches..................................... 10
4-5. Setting the foot switch operation mode.............. 22
4-6. Checking the error history....................................24
4-7. Input checking method.........................................25
4-8. Output checking method......................................28
4-9. Confirming software version ................................30
4-10. Protection settings .............................................31
5. EDITING PATTERN DATA.................. 34
5-1. Tension information in pattern data......................34
5-2. Work flowchart .....................................................35
5-3. Switching to pattern editing mode........................36
5-4. Checking pattern data..........................................36
5-5. Copying pattern data............................................37
5-6. Adding tension codes...........................................38
5-7. Changing tension codes ......................................39
5-8. Deleting tension codes.........................................40
7-7. Writing memory switch data to the SD card......... 48
7-8. Reading program data......................................... 49
7-9. Writing program data to an SD card .................... 50
7-10. Reading sewing machine data .......................... 51
7-11. Writing sewing machine data to an SD card...... 52
7-12. Writing error log data and memory switch log
data to an SD card ............................................ 53
7-13. Updating the control program version ............... 54
8. MECHANICAL DESCRIPTIONS ..........55
8-1. Needle bar and thread take-up mechanisms....... 55
8-2. Lower shaft and shuttle race mechanisms........... 55
8-3. Work clamp lifter mechanism............................... 56
8-4. Thread wiper mechanism .................................... 57
8-5. Feed mechanism................................................. 58
8-6. Thread trimmer mechanism................................. 59
8-7. Tension release mechanism................................ 60
8-8. Thread nipper mechanism (KE-430F -03, -0F,
-0K specifications only)........................................ 60
6. X AND Y PARALLEL MOVEMENT OF
SEWING PATTERNS........................... 41
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
10-14. Work clamp arm mechanism (KE-430F) ....... 100
10-15. Work clamp arm mechanism (BE-438F) ....... 101
10-16. Covers........................................................... 102
11. ADJUSTMENT.................................. 103
9. DISASSEMBLY ................................... 61
9-1. Covers .................................................................61
9-2. Work clamp arm mechanism................................62
9-3. Needle bar mechanism........................................63
9-4. Upper shaft mechanism.......................................64
9-5. Lower shaft mechanism.......................................66
9-6. Lubrication ...........................................................68
9-7. Feed mechanism .................................................69
9-8. Thread wiper mechanism.....................................70
9-9. Work clamp lifter mechanism...............................71
9-10. Threading mechanism .......................................73
9-11. Tension release mechanism..............................73
11-1. Standard thread tension.................................. 103
11-1-1. Upper and lower thread tension................ 104
11-1-2. Thread take-up spring............................... 105
11-1-3. Arm thread guide C................................... 106
11-1-4. Needle bar bush thread guide D............... 106
11-2. Adjusting the needle bar height....................... 106
11-3. Adjusting the needle bar lift amount and the
driver needle guard ......................................... 107
11-4. Adjusting the needle clearance ....................... 107
11-5. Adjusting the shuttle race thread guide ........... 108
11-6. Rotary hook lubrication amount....................... 108
11-7. Adjusting the thread trimming.......................... 109
11-8. Adjusting the position of the movable knife ..... 110
11-9. Replacing the movable knife and fixed knife ... 111
9-12. Thread nipper mechanism (KE-430F -03, -0F,
-0K specifications only)......................................74
9-13. Thread trimmer mechanism...............................75
9-14. Shuttle hook mechanism ...................................77
10. ASSEMBLY ....................................... 78
10-1. Thread trimmer mechanism (1)..........................78
10-2. Tension release mechanism..............................80
10-3. Threading mechanism .......................................80
10-4. Thread wiper mechanism ..................................81
10-5. Thread nipper mechanism.................................82
10-6. Work clamp lifter mechanism.............................83
10-7. Feed mechanism ...............................................86
10-8. Upper shaft mechanism.....................................90
10-9. Needle bar mechanism......................................92
10-10. Lower shaft mechanism...................................94
10-11. Lubrication.......................................................98
10-12. Shuttle hook mechanism .................................98
10-13. Thread trimmer mechanism (2) .......................99
11-10. Adjusting the work clamp lift amount
(KE-430F) ..................................................... 112
11-11. Adjusting the button clamp lift amount
(BE-438F) ..................................................... 112
11-12. Adjusting the holding pressure (BE-438F) .... 113
11-13. Adjusting the position of the button clamp
(BE-438F) ..................................................... 113
11-14. Adjusting the thread trimmer cam position .... 113
11-15. Adjusting the thread wiper............................. 114
11-16. Adjusting the tension release amount ........... 115
11-17. Adjusting the backlash amount (play) of the
lower shaft gear............................................. 116
11-18. Adjusting the home position .......................... 117
11-18-1. X- and Y-feed motor home positions ...... 117
11-18-2. Work clamp lift motor home position....... 119
11-18-3. Thread nipper motor home position........ 121
11-19. Adjusting the main shaft motor standard
position.......................................................... 123
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
11-20. Correcting the digital tension output ..............125
11-21. Checking the machine head switch ...............127
11-22. Setting method for standard depression
strokes (Foot switch) .....................................127
12. APPLYING GREASE........................129
12-1. Applying grease (Work clamp: KE-430F).........129
12-2. Applying grease
(When “GREASEUP” appears)........................129
13. HOW TO INSTALL THE FEED PLATE
FOR KE-430C SERIES IN KE-430F
AND BE-438F ................................. 133
14. INSTALLING THE 2-PEDAL FOOT
SWITCH (OPTION) ...........................134
15. ELECTRIC MECHANISM .................135
15-1. Precautions at the time of adjustment..............135
15-2. Components inside and outside the control box
and in the operation panel ...............................136
15-3. Fuse explanation .............................................137
15-4. Connectors ......................................................138
15-4-1. Connector positions ..................................138
15-4-2. Contact failure...........................................140
15-5. Troubleshooting...............................................144
15-5-1. Troubleshooting flowchart.........................144
15-5-2. Problem solution and measures................148
16. TABLE OF ERROR CODES.............163
17. TROUBLESHOOTING......................168
18. 7-SEGMENT DISPLAY.....................171
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
1. SPECIFICATIONS
1. SPECIFICATIONS
2452B
2278B
KE-430F
BE-438F
Electronic direct drive lockstitch bar tacker Electronic direct drive lockstitch button sewer
Stitch formation
Single needle lock stitch
Maximum sewing speed
Pattern size (X x Y)
3,200 sti/min
2,700 sti/min
40 x 30 mm max.
6.4 x 6.4 mm max.
Dimensions of buttons
that can be sewn
Outer diameter of button 8 - 30 mm (*1)
Feed mechanism
Stitch length
Y-θ intermittent feed mechanism (pulse-motor driven mechanism)
0.05 - 12.7 mm 0.05 – 6.4 mm
Refer to “List of Sewing Patterns” on the CD instruction manual for the number of stitches
in sewing patterns which have already been entered.
Number of stitches
Maximum stitch number
Work clamp lifter
Approx. 5,000 stitches (1 pattern)
Pulse-motor driven mechanism
Work clamp height
Button clamp height
17 mm max.
13 mm max.
Starting method
Hook
Foot switch or 2-pedal foot switch (option)
Shuttle hook (shuttle hook 2, optional)
Standard equipment
Shuttle hook
Digital tension set
Thread wiper device
Thread trimmer device
Standard equipment
Standard equipment
-03, -0K, -0F specifications:
Standard equipment ;
Thread nipper device
Option
-05 specifications: Option
Data storage method
Data recording media
Number of cycle programs
Flash memory (Any sewing pattern can be added using SD card)
SD card (*2)
Up to 30 can be registered (up to 50 steps each)
89 sewing patterns are set already
64 sewing patterns are set already
Number of stored data
(Up to a maximum of 512 additional types of sewing patterns. Total number of stitches of
stored data which can be added is within 500,000.) (*3)
Motor
AC servo motor 550 W
Machine head: approx. 57 kg, Operation panel: approx. 0.4 kg
Control box: approx. 9 kg
Weights
Power source
Single-phase 110V / 220V / 230V, 3-phase 220V / 380V / 400V 400VA
*1 Use the optional button clamp B (S03634-101) for diameters of 20 mm or greater.
*2 No guarantees of operation can be given for any media. Use one with a capacity of 2GB or less.
*3 The number of sewing patterns and the number of stitches that can be recorded will vary depending on the number of
stitches in each sewing pattern.
KE-430F, BE-438F
1
Download from Www.Somanuals.com. All Manuals Search And Download.
2. NOTES ON HANDLING
2. NOTES ON HANDLING
About the machine set-up location
・ Do not set up this sewing machine near other equipment such
as televisions, radios or cordless telephones, otherwise such
equipment may be affected by electronic interference from the
sewing machine.
・ The sewing machine should be plugged directly into an AC wall
outlet. Operation problems may result if extension cords are
used.
2516B
Carrying the machine
・ The machine should be carried by the arm by two people as
shown in the illustration.
・ When holding the machine head, do not hold it by the pulse
motor (1) or the solenoid (2), otherwise it may damage the
pulse motor (1) or the solenoid (2).
2517B
Tilting back the machine head
1. Pack away any tools which are near the table.
2. Secure the foot (A) so that the table will not move, and then pull
the arm with both hands to tilt back the machine head.
* While supporting the arm with both hands, gently lower it.
2518B
Returning the machine head to the upright position
1. Pack away any tools which are near the table.
2. While supporting the arm with both hands, gently return the
machine head to its original position.
2519B
KE-430F, BE-438F
2
Download from Www.Somanuals.com. All Manuals Search And Download.
3. RELATIONSHIP BETWEEN PROGRAMS AND PATTERNS
3. RELATIONSHIP BETWEEN PROGRAMS AND
PATTERNS
Programs specify the way that patterns (stitches) are to be sewn (parameters).
Program
Pattern
Parameter
X-scale
Y-scale
Sewing speed
Slow start pattern
Upper thread tension
etc. *1
2590B
<Programming method>
1. Use a standard pattern which has been registered in the actual sewing machine (430F: No. 1 to 89, 438F: 1 to 64) *2,
and save the pattern that you want to sew into that program number.
2. Set the parameters (such as X-scale, Y-scale, sewing speed and upper thread tension). This completes the program.
* When actually sewing, select the program number and then start sewing.
*1 Depending on the memory switch settings, the height of the work clamp/button clamp can also be set by means of
parameters.
*2 The PS300B can be used to create patterns and load them into actual sewing machines.
KE-430F, BE-438F
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. RELATIONSHIP BETWEEN PROGRAMS AND PATTERNS
・This sewing machine contains programs numbered 1 to 89 (1 to 64 for the 438F) which contain standard patterns, and can
also be programmed with additional programs numbered from 200 to 999.
Program number 1
Pattern
Parameter
number 1
Program number 2
Pattern
Parameter
number 2
Pattern numbers 1 to 89 (1 to 64 for the
438F) are registered (set) into program
Program number 3
Pattern
numbers 1 to 89 (1 to 64 for the 438F), and
only the parameters for these programs can
be set.
Parameter
number 3
Program number 89
Pattern
Parameter
number 89
Program numbers200 to 999
Standard patterns 1 to 89 (1 to 64 for the
Pattern
numbers 200 to 999
Parameter
438F) can be selected as desired for
program numbers 200 to 999. In addition,
patterns which have been created using the
PS300B can also be selected.
* Patterns 1 to 89 (1 to 64 for the 438F) are
listed in “2-2. List of Sewing Patterns
(KE-430F)” and “2-3. List of Sewing
Patterns (BE-438F)” in the CD instruction
manual.
2591B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
4
3. RELATIONSHIP BETWEEN PROGRAMS AND PATTERNS
・ After a program has been finished, you can revise the program by changing the setting details.
・ You can organize the use of program numbers so that, for instance, programs with the same pattern but different sizes or
upper thread tensions to suit the material being sewn are preset. (Refer to “5-2. Program setting method” in the CD
instruction manual.)
Example:
Program No. 200
・Pattern: No. 50
・X- and Y-scale: 150%
・Sewing speed: 2700 sti/min
・Upper thread tension: 100
…
Pattern: No. 50
Program No. 201
・Pattern: No. 50
・X- and Y-scale: 100%
・Sewing speed: 1000 sti/min
・Upper thread tension: 30
…
Program No. 202
・Pattern: No. 50
・X- and Y-scale: 50%
・Sewing speed: 2700 sti/min
・Upper thread tension: 200
…
2592B
The following table shows restrictions for sewing program numbers, pattern numbers and parameters.
Additional available
Standard programs
patterns
Initial value
Preset
Not preset
Set by user
430F / 438F
Model
430F 438F
430F
438F
430F 438F
200 - 999
(800 programs)
Sewing program No.
1 - 89 1 - 64 90 - 199
1 - 89 1 - 64
65 - 199
1 - 999
Number set when
program is created (512
programs from 200 to
999)
Pattern No.
Fixed at same number as sewing
program
X-scale (%)
Y-scale (%)
20 - 200
20 - 200
100
100
Sewing speed (sti/min)
Slow start pattern
430F: 200 - 3200 / 438F: 200 - 2700
2700 2300
Lo1 - 9
Lo8
Lo7
X parallel movement amount (mm)
When memory switch No. 465 is set to 3
Y parallel movement amount (mm)
When memory switch No. 465 is set to 3
-9.9 - 9.9
0.0
0.0
-9.9 - 9.9
Work clamp/button clamp height (high) (mm)
When memory switch No. 470 is set to ON.
430F: 10 - 17 / 438F: 6 - 13
14
1
10
1
Work clamp/button clamp height (medium) (mm)
When memory switch No. 470 is set to ON.
430F: 1 - 17 / 438F: 1 - 13
0 - 300
Upper thread tension setting value
75
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
5
4. FUNCTION SETTINGS
4. FUNCTION SETTINGS
4-1. List of special functions when power is turned on
This list shows the key operations for using special functions.
2593B
2594B
2599B
2595B
Data initialization function
Software version display function
1
2
5
6
Refer to the CD Instruction Manual.
Refer to “4-9. Confirming software version”.
2596B
Memory switch setting mode (Advanced)
Error log display function
2600B
Refer to “4-3. Setting memory switches (Advanced)”.
Refer to “4-6. Checking the error history”.
2597B
2601B
Input check function
Home position adjusting mode
3
4
7
8
Refer to “4-7. Input checking method”.
Refer to “11-18. Adjusting the home position”.
2598B
2602B
Output check function
Treadle position adjustment mode
Refer to “11-22. Setting method for standard
depression strokes (Foot switch)”.
Refer to “4-8. Output checking method”.
KE-430F, BE-438F
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
2603B
2605B
Main shaft motor standard position
adjustment mode
Protect setting mode
9
11
Refer to “11-19. Adjusting the main shaft motor
standard position”.
Refer to “4-10. Protection settings”.
2606B
2604B
Digital tension output correction mode
Version update
10
12
Refer to “7-13. Updating the control program
version”.
Refer to “11-20. Correcting the digital tension output”.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
7
4. FUNCTION SETTINGS
4-2. List of advanced functions
This list shows the key operations for using advanced functions.
2607B
2612B
2608B
Memory switch setting mode (Standard)
Cycle program setting mode
1
5
6
7
Refer to the CD Instruction Manual.
Refer to the CD Instruction Manual.
2613B
2609B
Lower thread counter setting mode
Pattern data editing mode
2
3
Refer to the CD Instruction Manual.
Refer to “5-3. Switching to pattern editing mode”.
2614B
2610B
Production counter setting mode
Parallel movement mode
Refer to “6. X and Y parallel movement of sewing
patterns”.
Refer to the CD Instruction Manual.
2615B
2611B
Program mode
SD data read/write mode
4
8
Refer to “7-3. Preparation for reading and writing
data”
Refer to the CD Instruction Manual.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
8
4. FUNCTION SETTINGS
4-3. Setting memory switches (Advanced)
Change the mode to memory switch setting mode.
While pressing the TEST key and the SELECT key, turn
on the power switch.
1
All indicators switch off
・ The memory switch number will be displayed in the
PROGRAM No. display and the setting value for that
number will be displayed in the menu display.
2420B 2616B
Select the memory switch that you would like to Press the
change the setting for.
number.
or
key to select the memory switch
2
2422B
If you would like to display only the numbers of While pressing the SELECT key, press the
memory switches that have been changed from (1).
or
key
default settings
・ The numbers of memory switches that have been
changed from default settings will appear in order.
2423B
Change the memory switch setting.
3
4
Press the
or
key to change the setting value.
・ The flashing display means that the setting has not yet
been applied.
・ You can make the initial setting appear in the display
by pressing the RESET key.
2424B
Apply the changed setting.
Press the ENTER key.
・ The menu display will change from flashing to
illuminated, and this means that the parameter setting
has been applied.
・ If you press the
or
key (1) or the TEST key
without pressing the ENTER key, you can cancel the
parameter changes.
2414B
Repeat steps 2 to 4 above to set each memory switch.
5
6
Exit setting mode.
Press the TEST key.
・ The changes will be memorized and the sewing
machine will switch to home position detection
standby.
2404B
TEST indicator switches off
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
9
4. FUNCTION SETTINGS
4-4. List of memory switches
NOTE:
In standard memory switch setting mode (refer to the CD Instruction Manual), the bottom two digits only display memory
switch Nos. 00 to 49. The bottom two digits do not display memory switch Nos. 50 to 99.
Work clamp/button clamp settings (001 − 099)
Initial
value
No.
Setting range
Setting units
Setting details
Work clamp/button clamp lift timing when sewing is complete
OFF: Does not lift automatically.
1: Lifts at the final stitch position.
001
1
1
OFF, 1 − 2
2: Lifts after moving to the sewing start position.
Work clamp/button clamp operation before moving to the sewing start
position
ON: The work clamp/button clamp can operate vertically even before
moving to the sewing start position.
OFF: The work clamp/button clamp cannot operate vertically before
moving to the sewing start position.
Work clamp/button clamp operation during pause (split program)
ON: The work clamp/button clamp cannot rise automatically during a
pause (split program).
051
052
ON/OFF
ON/OFF
OFF
OFF
-
-
OFF: The work clamp/button clamp can rise automatically during a
pause (split program).
Time after the work clamp/button clamp drops until the upper shaft
starts rotating
0 − 3000
060
070
0
1
10
1
(ms)
Type of foot switch used
1: Foot switch
2: 2-pedal foot switch (option)
1 − 2
1 − 2
Foot switch operating mode
* Enabled when No. 070 is set to “1”. (Refer to page 22.)
1: (1st step) Drop Æ (2nd step) Start
071
1
1
2: (1st step) Drop to intermediate height Æ (2nd step) Drop and start
2-pedal foot switch operating mode
* Enabled when No. 070 is set to “2”. (Refer to page 23.)
1: (Work clamp switch 1st step) Drop, (Start switch) Start
2: (Work clamp switch 1st step) Drop to intermediate height Æ (Work
clamp switch 2nd step) Drop, (Start switch) Start
3: (While work clamp switch depressed to 1st step) Work clamp/button
clamp rises, (Start switch) Start
072
1
1
1 − 5
4: (Work clamp switch 1st step) Drop Æ (Work clamp switch 2nd step)
Start
5: (Work clamp switch 1st step) Drop to intermediate height Æ (Work
clamp switch 2nd step) Drop and start
KE-430F, BE-438F
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
Sewing machine motor settings (100 − 199)
Initial
value
No.
Setting range
Setting units
Setting details
Slow start pattern setting method
ON: Follows the slow start patterns for each program.
(Refer to “5-2. Program setting method” in the CD Instruction
Manual.)
100
ON/OFF
ON
-
OFF: The sewing speed for the first 1 - 5 stitches is set by
memory switch Nos. 151 – 155.
Highest needle position stop
ON: When the upper shaft stops, the motor operates in
reverse to return the needle bar close to its highest
position.
NOTE:
When the motor operates in reverse to raise the
needle, the thread take-up will stop at a position
which is lower than its normal stopping position. As a
result, the thread take-up will rise slightly at the
sewing start. This may result in the thread pulling out
under certain conditions.
150
ON/OFF
OFF
-
OFF: Disabled
430F: 200 − 3200
(sti/min)
438F: 200 − 2700
(sti/min)
430F: 200 − 3200
(sti/min)
438F: 200 − 2700
(sti/min)
430F: 200 − 3200
(sti/min)
438F: 200 − 2700
(sti/min)
430F: 200 − 3200
(sti/min)
438F: 200 − 2700
(sti/min)
430F: 200 − 3200
(sti/min)
438F: 200 − 2700
(sti/min)
430F: 400 − 3200
(sti/min)
438F: 400 − 2700
(sti/min)
430F: 400 − 3200
(sti/min)
438F: 400 − 2700
(sti/min)
430F: 400 − 3200
(sti/min)
438F: 400 − 2700
(sti/min)
1st stitch sewing speed at the sewing start
* Enabled when No. 100 is set to “OFF”.
151
152
153
154
155
156
157
158
159
*1
*1
*1
*1
*1
*1
*1
*1
*1
100
100
100
100
100
100
100
100
100
2nd stitch sewing speed at the sewing start
* Enabled when No. 100 is set to “OFF”.
3rd stitch sewing speed at the sewing start
* Enabled when No. 100 is set to “OFF”.
4th stitch sewing speed at the sewing start
* Enabled when No. 100 is set to “OFF”.
5th stitch sewing speed at the sewing start
* Enabled when No. 100 is set to “OFF”.
Sewing speed for 5th stitch before the sewing end
Sewing speed for 4th stitch before the sewing end
Sewing speed for 3rd stitch before the sewing end
Sewing speed for 2nd stitch before the sewing end
430F: 400 − 3200
(sti/min)
438F: 400 − 2700
(sti/min)
*1: The initial value will vary depending on the specifications. (Refer to “Initial values for each application” on the following
page.)
KE-430F, BE-438F
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
Initial values for each application
No.
151
152
153
154
155
156
157
158
159
KE-430F-03
800
KE-430F-05
1500
KE-430F-0K
400
KE-430F-0F
800
BE-438F
400
1200
2000
800
1200
400
2500
2500
1200
2500
3200
3200
3200
3200
2400
2500
600
3200
3200
3200
900
3200
3200
3200
2700
2700
2700
2700
2700
3200
3200
3200
3200
3200
3200
3200
3200
3200
2400
2700
2400
Initial
value
No.
161
Setting range
Setting units
Setting details
Effective hammer operation when needle does not pierce
ON: Enabled
ON/OFF
OFF
-
OFF: Disabled
Regulation of sewing speed changes due to sewing pitch
changes
ON: Restricted (Speed is fixed at the minimum sewing speed
for the maximum pitch of the sewing data.)
* Set to ON if there may be a problem with sewing
speed changes as a result of pitch changes.
OFF: Not restricted (Sewing speed varies depending on
sewing pitch of the sewing data.)
162
ON/OFF
OFF
-
430F: 1200 − 3200
(sti/min)
438F: 1200 − 2700
(sti/min)
3200
2700
Sewing speed limit value
* When setting the sewing speed, the speed will be limited by
this value.
163
164
100
-
Thread trimming operation prevention
ON: All thread trimming operations are disabled.
OFF: Thread trimming is carried out in accordance with the
sewing data.
ON/OFF
OFF
Stop position at highest needle position stop
−: Becomes higher
-20 − 20
165
166
167
0
1
10
-
(degrees)
+: Becomes lower
Delay time until reverse operation starts during highest needle
position stop operation
10 − 500
(ms)
150
OFF
Servo lock operation
ON: Used
ON/OFF
OFF: Not used
Servo lock timer setting
* Enabled when No. 167 is set to “ON”.
OFF: No timer operation
1 to 120: Timer operation (1 to 120 secs.)
OFF, 1 − 120
168
169
170
OFF
45
1
1
(seconds)
Servo lock release rotation angle
* Enabled when No. 167 is set to “ON”.
30 − 89
(degrees)
430F: 0 − 2800
(sti/min)
438F: 0 − 2300
(sti/min)
Lowers the allowable speed for the sewing pitch by the
amount set.
However, the minimum allowable speed value is 400 sti/min.
0
100
Automatic needle lifter operation
ON: If the needle bar is not at the needle up stop position
during work clamp/button clamp home position detection,
it moves automatically to the needle up stop position.
OFF: An “UP” error is displayed without the needle bar moving
automatically.
171
ON/OFF
ON
-
(No. 655 can also be used to ignore this sensor.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
12
4. FUNCTION SETTINGS
Feed settings (200 − 299)
No.
Setting range Initial value Setting units
Setting details
Single stitch test feed
ON: During test feeding, the mechanism moves one stitch at a time
when the foot switch is depressed to the 2nd step (for a
2-pedal foot switch, when the start switch is depressed).
In addition, when the test indicator is illuminated, test feeding
will move forward one stitch at a time when the machine pulley
is turned by hand.
OFF: During test feeding, sewing starts and automatically
continues to the last stitch when the foot switch is
depressed to the 2nd step (for a 2-pedal foot switch, when
the start switch is depressed).
430F:OFF
200
ON/OFF
-
438F:ON
Home position detection at the sewing end
ON: At the sewing end, the work clamp/button clamp will detect the
home position and then move to the sewing start position.
OFF: At the sewing end, the work clamp/button clamp will move to
the sewing start position.
Feeding speed
1: 100 mm/s (Slow)
2: 200 mm/s
250
251
ON/OFF
OFF
-
3
1
1 − 5
3: 300 mm/s
4: 400 mm/s
5: 500 mm/s (Fast)
High-speed test feed method
* Enabled when No. 200 is set to “OFF”.
ON: High-speed feeding starts at the same time test feeding starts.
OFF: Normally slow, but becomes faster when the foot switch is
depressed to the 1st step (for a two-pedal foot switch, when
the work clamp switch is depressed).
252
ON/OFF
OFF
-
Moving method to the sewing start point
0: Depress the foot switch to the 2nd step (for a two-pedal foot
switch, depress the start switch) while the program number is
flashing.
1: Press the RESET key while the program number is flashing.
2: Press the special external input switch (option input (IN3)) while
the program number is flashing.
253
*1
0
1
0 − 2
Changes the overall feed timing
−: Feed timing becomes earlier.
+: Feed timing becomes later.
Changes the feed timing for the 1st stitch at the sewing start
−: Feed timing becomes earlier.
+: Feed timing becomes later.
Changes the feed timing for the 2nd stitch at the sewing start
−: Feed timing becomes earlier.
+: Feed timing becomes later.
Changes the feed timing for the 3rd stitch at the sewing start
−: Feed timing becomes earlier.
+: Feed timing becomes later.
Changes the feed timing for the 3rd stitch before the sewing end
−: Feed timing becomes earlier.
+: Feed timing becomes later.
Changes the feed timing for the 2nd stitch before the sewing end
−: Feed timing becomes earlier.
+: Feed timing becomes later.
Changes the feed timing for the 1st stitch before the sewing end
−: Feed timing becomes earlier.
+: Feed timing becomes later.
-80 − 80
260
261
262
263
264
265
266
*2
*2
*2
*2
*2
*2
*2
1
1
1
1
1
1
1
(degrees)
-80 − 80
(degrees)
-80 − 80
(degrees)
-80 − 80
(degrees)
-80 − 80
(degrees)
-80 − 80
(degrees)
-80 − 80
(degrees)
*1: This is not initialized during initialization mode.
*2: The initial value will vary depending on the specifications. (Refer to “Initial values for each application” on the following
page.)
KE-430F, BE-438F
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
Initial values for each application
No.
260
261
262
263
264
265
266
KE-430F-03
KE-430F-05
KE-430F-0K
KE-430F-0F
BE-438F
10
-15
45
45
45
0
-15
50
45
45
25
35
0
-15
45
45
45
0
-15
45
45
45
0
-80
-50
-50
0
35
35
35
35
35
35
15
15
Initial
value
No.
267
Setting range
Setting units
Setting details
If the overall feed timing (setting No. 260) has been changed
from the default value, this specifies the effective number of
stitches.
OFF, 1 − 99
(stitches)
OFF: No limit
OFF
1
1
1 to 99: When the specified number of stitches from the
sewing start is exceeded, the feed timing returns to
the standard timing.
Changes the overall feed timing reference.
0: [Feed start reference] Makes the timing uniform at the start
of feed.
1: [Needle up reference] Changes the timing at the start of
feed so that the feed moves half the feed width when the
needle bar is at its highest position.
2: [Feed end reference] Makes the timing uniform at the end
of feed.
Changes the feed timing reference for the first three stitches at
the sewing start.
0: [Feed start reference] Makes the timing uniform at the start
of feed.
1: [Needle up reference] Changes the timing at the start of
feed so that the feed moves half the feed width when the
needle bar is at its highest position.
268
269
1
0 − 2
430F: 0
438F: 1
1
0 − 2
2: [Feed end reference] Makes the timing uniform at the end
of feed.
Moving method to the sewing start point after the program is
changed
* However, operation for the "0" setting is always carried out
when No. 273 is set to ON.
0: Moves to sewing start position and then stops.
2: Home position detection is carried out, then moves to the
sewing start position and stops.
Work clamp/button clamp standby position
ON: For the 430F, the center of the sewing area is the standby
position (escape point).
270
271
2
2
-
0 − 2
ON/OFF
OFF
For the 438F, the front is the standby position (escape
point).
OFF: The sewing start position becomes the standby position.
Reduced feed noise
272
273
ON/OFF
ON/OFF
OFF
OFF
-
-
ON: Enable (Operating speed is limited to 2500 sti/min.)
OFF: Disable
Start switch operation after program is changed
ON: Moves to sewing start position and starts (program No.
illuminates)
OFF: Only moves to sewing start position (program No.
flashes)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
14
4. FUNCTION SETTINGS
Operation panel settings (300 − 399)
No.
Setting range
Initial value Setting units
Setting details
Production counter display
300
ON/OFF
OFF
OFF
OFF
-
-
-
ON: Production counter display
OFF: Lower thread counter display
Production counter counting units
ON: Counted for each cycle program.
OFF: Counted for each item of sewing data.
* Counted for each individual split when No. 451 is set to
“ON”.
Lower thread counter counting operation
ON: Counted at the sewing start.
OFF: Counted at the sewing end.
352
353
ON/OFF
ON/OFF
Program settings (400 − 499)
No.
Setting range
Initial value Setting units
Setting details
Button hole distance display
* Enabled when No. 402 is set to “ON” and (for the BE-438F)
when pattern No. 1 to 64 (buttonhole data) is selected.
ON: X-scale and Y-scale will be displayed as button hole
distances (mm).
OFF: X-scale and Y-scale will be displayed as pattern outer
dimensions (mm).
401
ON/OFF
OFF
OFF
-
-
X-scale/Y-scale mm display
* The mm display may vary from actual sewing dimensions.
ON: Displayed as mm.
402
404
ON/OFF
ON/OFF
OFF: Displayed as %.
Display for program numbers 1 to 89 (1 to 64 for BE-438F)
ON: Program numbers 1 to 89 (1 to 64 for the BE-438F) are
displayed during program number selection operations.
OFF: Program numbers 1 to 89 (1 to 64 for the BE-438F) are
skipped during program number selection operations so
that these numbers cannot be selected.
* If no other programs have been recorded, the setting will
return to “ON”.
Cycle program No. display (C01 to C30)
ON: Cycle program numbers are displayed during program
number selection operations.
OFF: Cycle program numbers are skipped during program
number selection operations so that these numbers
cannot be selected.
ON
ON
-
-
405
ON/OFF
Program numbers switched by F keys
0: When the F1 to F4 keys are pressed, operation switches to
program numbers 1 to 4.
1: When the F1 to F4 keys are pressed, operation switches to
program numbers 201 to 204.
2: When the F1 to F4 keys are pressed, operation switches to
cycle program numbers C01 to C04.
3: When the F1 to F4 keys are pressed, operation switches to
the program number which has been pre-assigned to the
respective key.
406
0
1
0 − 3
Assignment to F1 key: Memory switch No. 407
Assignment to F2 key: Memory switch No. 408
Assignment to F3 key: Memory switch No. 409
Assignment to F4 key: Memory switch No. 410
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
15
4. FUNCTION SETTINGS
No.
407
Setting range
1 − 999,
C01 − C30
1 − 999,
C01 − C30
1 − 999,
C01 − C30
1 − 999,
Initial value Setting units
Setting details
Program No. assigned to the F1 key
* Enabled when No. 406 is set to “3”.
Program No. assigned to the F2 key
* Enabled when No. 406 is set to “3”.
Program No. assigned to the F3 key
* Enabled when No. 406 is set to “3”.
Program No. assigned to the F4 key
1
2
3
4
-
-
-
-
408
409
410
C01 − C30
* Enabled when No. 406 is set to “3”.
Split mode selection
451
ON/OFF
OFF
-
ON: Independent split mode
OFF: Continuous split mode
430F: 40.0
438F: 6.4
430F: 40.0
438F: 6.4
0.0 − 40.0
460
461
0.1
0.1
X direction sewing area limitation
Y direction sewing area limitation
(mm)
0.0 − 30.0
(mm)
Enlargement/reduction reference point
0: Center of sewing frame
1: Sewing start point
2: Center of pattern
3: Front of pattern center
4: Back of pattern center
5: Back-left corner of sewing area
6: Front-left corner of sewing area
7: Back-right corner of sewing area
8: Front-right corner of sewing area
Enlargement/reduction of bar tacking
ON: Bar tacking stitch lengths (pitch less than approx. 1 mm)
are also enlarged or reduced.
462
463
0
1
0 − 8
ON/OFF
OFF
-
OFF: Bar tacking stitch lengths (pitch less than approx. 1 mm)
are not enlarged or reduced.
Setting parallel movement amount for sewing pattern
1: The parallel movement amount for the currently-selected
program can be set in parallel movement mode.
The movement amount is initialized when the power is
turned off and when the program number, pattern number,
X-scale or Y-scale is changed.
2: The parallel movement amount for the currently-selected
program can be set in parallel movement mode.
The movement amount is retained when the power is
turned off, but is initialized when the program number,
pattern number, X-scale or Y-scale is changed.
3: The movement amount can be set for each program using
parameters.
465
1
1
1 − 3
The movement amount is retained when the power is
turned off and when the program number, X-scale or
Y-scale is changed, but is initialized when the pattern
number is changed.
Tension value setting
ON: A common tension value is set for all programs.
* Uniform correction operations are not possible.
OFF: Set separately for each program.
Work clamp/button clamp height setting for each program
ON: Work clamp/button clamp height is set separately for each
program.
469
470
471
ON/OFF
ON/OFF
OFF
OFF
-
-
OFF: A common work clamp/button clamp height is set for all
programs.
* The work clamp/button clamp height is set by Nos. 471
and 472.
430F: 10 − 17
(mm)
438F: 6 − 13
(mm)
14
10
Work clamp/button clamp raise position setting
* Enabled when No. 470 is set to “OFF”.
1
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
16
4. FUNCTION SETTINGS
No.
472
Setting range
430F: 1 − 17
(mm)
438F: 1 − 13
(mm)
Initial value Setting units
Setting details
Work clamp/button clamp intermediate drop position setting
* Enabled when No. 470 is set to “OFF”.
1
1
<Work clamp lifting height>
* When memory switch No. 470 is set to “ON”, the following parameters are displayed during program mode and sewing
standby mode.
Setting range
Item
Display during program mode
Display during sewing standby mode
and initial value
430F：
10 − 17mm
438F：
6 − 13mm
Setting units: 1mm
Work
clamp/button
clamp height
(raised)
(Initial settings are:
430F: 14mm,
438F: 10mm)
For example,
initial value for
430F
2780B
2781B
430F：
1 − 17mm
438F：
1 − 13mm
Setting units: 1mm
Work
clamp/button
clamp height
(intermediate
drop)
(Initial setting is 1mm)
* This is displayed
when memory switch
No. 071 is set to “2”
or when memory
switch No. 072 is set
to “2” or “5”.
Initial value
2782B
2783B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
17
4. FUNCTION SETTINGS
<X and Y parallel movement amounts>
* When memory switch No. 465 is set to “3”, the following parameters are displayed during program mode and sewing
standby mode.
Setting range
and initial value
Item
Display during program mode
Display during sewing standby mode
-9.9 − 9.9mm
Setting units: 0.1mm
(Initial setting is 0.0mm)
+ direction:
X
parallel
Work clamp/button
clamp moves to
the left.
movement
amount
Initial value
2784B
2785B
-9.9 − 9.9mm
Setting units: 0.1mm
(Initial setting is 0.0mm)
+ direction:
Y
parallel
Work clamp/button
clamp
forward.
movement
amount
moves
Initial value
2786B
2787B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
18
4. FUNCTION SETTINGS
Device settings (500 − 599)
No.
Setting range
Initial value
OFF
Setting units
Setting details
Thread nipper operation
ON: Used
* However, all of the following conditions must be
satisfied.
500
ON/OFF
-
Memory switch No. 100 = ON
Memory switch No. 566 = ON
Slow start speed is Lo8 or Lo9
Sewing speed is 1500 sti/min. or more
OFF: Not used
Output continue time for needle cooler device when sewing
machine is stopped
OFF: Needle cooler device is not used
OFF,
100 − 2000
(ms)
550
551
OFF
100
1
100 to 2000: Output is continued for the specified time.
430F-03:OFF
430F-05:1
430F-0K:OFF
430F-0F:OFF
438F:OFF
Upper thread tension release at the sewing start
* Only enabled when the thread nipper is not operating.
OFF: Not released
OFF, 1 − 3
(stitches)
1 to 3: Released during the specified number of stitches.
Use of the thread breakage sensor (available by special order)
ON: Used
OFF: Not used
Sewing start sensing sensitivity for thread breakage sensor
(available by special order)
ON: 10 stitches at sewing start
OFF: 5 stitches at sewing start
Thread nipper device installation
ON: Installed
554
*1
ON/OFF
ON/OFF
OFF
-
-
555
*1
OFF
430F-03:ON
430F-05:OFF
430F-0K:ON
430F-0F:ON
438F:OFF
* The thread nipper device only operates when all of the
following conditions are satisfied.
Memory switch No. 100 = ON
Memory switch No. 500 = ON
Slow start speed is Lo8 or Lo9
Sewing speed is 1500 sti/min. or more
566
*2
ON/OFF
ON/OFF
-
-
OFF: Not installed
NOTE:
If the thread nipper device is installed, do not set this to
“OFF”. If this is not observed, damage may occur.
Upper thread tension during feeding while upper shaft is
stopped
ON: Not released
OFF: Released
567
OFF
-80 − 115
580
581
0
0
5
5
Nip timing offset for thread nipper device
(degrees)
-160 − 110
(degrees)
Release timing offset for thread nipper device
*1: These functions can be used if the main PCB version is 1.5.00 or later.
*2: This is not initialized during initialization mode.
KE-430F, BE-438F
19
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
No.
582
Setting range
ON/OFF
Initial value
ON
Setting units
1
Setting details
Upper thread tension tightening at the sewing start
ON: Enabled
OFF: Disabled
Upper thread tension change (tightening) angle offset at the
sewing start
-150 − 150
583
584
585
587
588
589
590
591
592
593
594
0
0
5
5
(degrees)
-110 − 40
(degrees)
Upper thread tension release angle offset at the sewing end
Upper thread tension value (tightening) at the sewing start
Upper thread tension value (release) at the sewing start
Thread trimmer solenoid ON timing
470
0
1
0 − 500
0 − 300
1
0 − 50
(ms)
35
20
5
1
0 − 50
(ms)
1
Thread trimmer solenoid ON time
1
Thread trimmer solenoid holding force
5 − 10
430F: 270
438F: 260
0 − 300
(degrees)
5
Specified final speed output angle offset
200 − 700
(sti/min)
600
8
100
1
Last stitch sewing speed for upper shaft motor
Speed change delay until thread nipper operation is complete
* If the thread nipper device is not to operate, set to “0”.
0 − 15
(ms)
-160 − 20
(degrees)
0
5
Needle up stop signal output angle offset
Error processing settings (600 − 699)
Initial
value
No.
Setting range
Setting units
1
Setting details
Error release method when operation has stopped
0: Press the RESET key on the operation panel.
1: Press the STOP switch (available by special order).
2: Press the external input switch (EXIN2).
Needle stop position when sewing is interrupted by the STOP
switch (available by special order)
ON: Needle stops in the up position.
OFF: Needle stops in the down position.
Thread trimming operation when sewing is paused
ON: Thread trimming is not carried out when the pause is
canceled.
650
*1
*2
0
0 − 2
651
*2
ON/OFF
ON/OFF
OFF
-
-
652
*2
OFF
OFF: Thread trimming is carried out when the pause is
canceled.
Use of STOP switch (available by special order)
ON: Used
OFF: Not used
Disables needle up stop position monitoring.
ON: Disabled
OFF: Enabled (If the needle up stop position is incorrect, “UP”
will be displayed.)
Time from error occurring to buzzer stopping
OFF: Buzzer does not stop.
2 – 30: Buzzer stops after the specified time.
654
*2
ON/OFF
ON/OFF
OFF
OFF
OFF
-
-
655
657
OFF, 2 − 30
(seconds)
2
*1: This is not initialized during initialization mode.
*2: These functions can be used if the main PCB version is 1.5.00 or later.
KE-430F, BE-438F
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
Maintenance settings (700 − 799)
Initial
value
No.
Setting range
Setting units
Setting details
Continuous operation mode (for administrator)
ON: Continuous operation is repeated while the foot switch is
being depressed to the 2nd step (for a 2-pedal foot
switch, while the start switch is being depressed).
NOTE:
750
ON/OFF
OFF
-
This setting is for use by an administrator in test
running mode. It is dangerous to set it to “ON” for
normal sewing, so it should always be set back to
“OFF” after use.
OFF: Disabled
Continuous operation cycle time adjustment timer (for
administrator)
* Enabled when No. 750 is set to “ON”.
0 − 3000
751
752
200
0
10
1
(ms)
Sewing machine ID code (for specifying SD card folder)
Thread winding speed limit
0 − 99
ON: Upper limit is limited to 2000 sti/min.
* If the speed specified at the operation panel exceeds
2000 sti/min, thread winding will be limited to 2000
sti/min.
756
ON/OFF
ON
-
OFF: Upper limit is not limited to 2000 sti/min.
* Thread winding is carried out at the speed specified at
the operation panel.
Specification and destination settings (800 − 899)
Initial
value
No.
Setting range
Setting units
Setting details
430F-03: 3, 5, K, F
430F-05: 3, 5, K, F
430F-0K: 3, 5, K, F
430F-0F: 3, 5, K, F
438F-03: 3
3
Specification code setting
* The 438F has only -03 specifications.
3: -03 specifications (medium-weight material)
5: -05 specifications (heavy-weight material)
K: -0K specifications (knitted wear)
5
K
F
3
850
*1
-
F: -0F specifications (foundation garments)
*1: This is not initialized during initialization mode.
Unique settings for each model (900 − 999)
Initial
value
No.
Setting range
Setting units
1
Setting details
Eyelet bar tack closing device (old 432 series)
OFF: Disable
1: Eyelet bar tacker closing device operates after the work
951
OFF
OFF, 1 − 2
clamp has dropped.
2: Eyelet bar tack closing device operates at the sewing start.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
21
4. FUNCTION SETTINGS
4-5. Setting the foot switch operation mode
● When using a foot switch
The following table describes the operation of the work clamp/button clamp during sewing standby mode when using the foot
switch.
Neutral
1st step
2nd step
4441Q
1. Set memory switch No. 070 to “1”.
2. Use memory switch No. 071 to select the desired operation mode from the following.
* In the following table, the term “work clamp” refers to the work clamp/button clamp.
Foot switch
Neutral
1st step
1st step
2nd step
Setting
value
No. 071
Depress
1st step
2nd step
Neutral
Depressed further
Release
Work clamp
maximum drop
Sewing machine
start
1
2
Work clamp raised
Work clamp raised
Work clamp
maximum drop +
sewing machine
start
Work clamp
intermediate drop
2984B 2985B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
22
4. FUNCTION SETTINGS
● When using a 2-pedal foot switch (option)
The following table describes the operation of the work clamp/button clamp during sewing standby mode when using a
2-pedal foot switch.
Work clamp switch (2-step)
Start switch
4923Q
1. Set memory switch No. 070 to “2”.
2. Use memory switch No. 072 to select the desired operation mode from the following.
* In the following table, the term “work clamp” refers to the work clamp/button clamp.
Work clamp switch (left side)
1st step
Neutral
1st step
Setting
value
Start switch
(right side)
2nd step
No. 072
Depress
Release
Depressed further
Release slightly
1st step
2nd step
Neutral
Work clamp raised
Work clamp
maximum drop
Sewing
machine
start *1
Work clamp
maximum drop
1
1
*
Work clamp
raised
Work clamp raised
Work clamp
intermediate drop
Work clamp raised
Work clamp
intermediate drop
Sewing
machine
start *1
Work clamp
maximum drop
2
Work clamp
Work clamp
maximum drop
1
maximum drop
*
Work clamp raised
Work clamp
raised
Sewing
machine
start *1
Work clamp
maximum drop
Work clamp
raised
1
3
4
5
*
Work clamp
maximum drop
Sewing
machine start
Work clamp raised
Work clamp raised
Work clamp
maximum drop
+ sewing
Work clamp
intermediate
drop
machine start
*1 Enabled when the work clamp switch is at neutral and the work clamp/button clamp is fully lowered.
2986B 2987B
KE-430F, BE-438F
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
4-6. Checking the error history
The past error history can be checked by the following procedure.
2617B
1. While pressing the
key (1), turn on the power switch.
The error history number will appear in the PROGRAM No. display (2) and the error code will appear in the menu display
(3).
NOTE:
E025, E035, E065, E705 and error codes which can be reset do not remain in the error history, and so they will not be
displayed.
2. Press the
or
key (4) to change the order of the error history number.
The history stores 99 entries (01 to 99) in order starting from the most recent. No. 01 is the most recent entry. (If there are
no error codes, “E---“ will be displayed.
The production counter when the error occurred will appear in the PROGRAM No. display (2) and the menu display (3) in
units of 100 stitches while the
key (6) is being pressed.
3. Press the TEST key (5) to return to the normal display. The sewing machine will switch to home position detection
standby.
KE-430F, BE-438F
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
4-7. Input checking method
This is used at the following times.
・When you would like to check for problems with the operation panel
・When you would like to check for broken cords
・When you would like to adjust a sensor position
This lets you check if the CPU is reading signals from the keys and the sensors correctly.
2618B
1. While pressing the
key (1), turn on the power switch.
The item number will appear in the PROGRAM No. display (2), the item name will appear in the tension display (3), and
the input status will appear in the menu display (4).
2. Press the
key (1) or the
key (5) to select the desired item number.
3. Refer to the input check list to check the key and sensor responses.
4. When returning to normal operation, turn power off and then on again.
< Input check list >
Item No.
Item name
Input status
on] / [ oFF]
Check items and checking methods
X-feed motor home position sensor position
Move the work clamp/button clamp manually in the X direction.
Left = ON, right = OFF.
X-feed motor encoder counter value
Move the work clamp/button clamp manually in the X direction.
[
[
1]
2]
[orX]
[
[EnX]
[-999] − [ 999]
Right = down, and left = up.
* When the power is turned on, the position will be “0”.
Y-feed motor home position sensor position
Move the work clamp/button clamp manually in the Y direction.
Back = ON, and forward = OFF.
Y-feed motor encoder counter value
Move the work clamp/button clamp manually in the Y direction.
* Back = down, and forward = up.
[
[
3]
4]
[orY]
[
on] / [ oFF]
[EnY]
[-999] − [ 999]
* When the power is turned on, the position will be “0”.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
25
4. FUNCTION SETTINGS
Item No.
Item name
Input status
on] / [ oFF]
Check items and checking methods
Work clamp motor home position sensor position
Remove the side cover and raise the work clamp/button clamp
[
5]
[orP]
[
manually.
* ON when raised, OFF when lowered.
Work clamp motor encoder counter value
Remove the side cover and raise the work clamp/button clamp
manually.
* Back = down, and forward = up.
* When the power is turned on, the position will be “0”.
Upper shaft 360 rotation segment signal
Turn the pulley by hand.
* The forward direction (the direction of the arrow) = up.
Needle up signal
Turn the pulley by hand.
* ON in the needle up region, OFF in any other region.
Shows the input voltage.
Operation panel key input check
The key name will be displayed while a key is pressed.
Key name
[
[
6]
7]
[EnP]
[-999] − [ 999]
[ 000] − [ 359]
[dEG]
[ UP]
[
[
8]
9]
[
on] / [ oFF]
[voL]
[PnL]
[ ***]
[ 10]
[*] / [ oFF]
* ON display
[rESt]
RESET key
[tESt]
TEST key
[tHrE]
THREAD/CLAMP key
[ tEn]
TENSION key
[SELE]
[UP-M]
[dn-M]
[UP-S]
[dn-S]
[UP-t]
SELECT key
key
key
SECTION + key
SECTION - key
TENSION + key
[dn-t]
TENSION - key
[
[
[
[
F1]
F2]
F3]
F4]
Function key F1
Function key F2
Function key F3
Function key F4
[ Ent]
ENTER key
Foot switch analog value
Depress the foot switch.
* When depressed forward, the value increases.
* Should normally display somewhere around 102 when at the
neutral position.
Foot switch signal
bAck: Depressed backward
oFF：Neutral
CLnP：1st step (Work clamp signal)
[ 11]
[ 12]
[FtA]
[FtS]
[
0] − [ 255]
[bAck] / [oFF] /
[CLnp] / [Strt]
Strt：2nd step (Start signal)
Work clamp switch 1st step for 2-step foot switch
Depress the work clamp switch to the 1st step.
Work clamp switch 2nd step for 2-step foot switch
Depress the work clamp switch to the 2nd step.
Start switch for 2-step foot switch
[ 13]
[ 14]
[ 15]
[CL1]
[CL2]
[Stt]
[
[
[
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
Depress the start switch.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
26
4. FUNCTION SETTINGS
Item No.
[ 16]
Item name
[EMC]
Input status
no] /
[ oFF] / [ on]
Check items and checking methods
Stop switch (option)
* [ no] is displayed when not connected.
[
Machine head switch
[ oFF] is displayed when the machine head is tilted back.
Thread nipper home position sensor
[ 17]
[HEd]
[
on] / [ oFF]
Press the
direction.
Press the
direction.
key to move the thread nipper in the home position
[ 18]
[orn]
[
on] / [ oFF]
key to move the thread nipper in the retract
* [ on] is displayed for the retract direction.
Thread nipper motor encoder counter value
Press the
direction.
Press the
direction.
key to move the thread nipper in the home position
key to move the thread nipper in the retract
[ 19]
[Enn]
[-999] − [ 999]
* Retract direction = down, home direction = up
* When the power is turned on, the position will be “0”.
Option input (IN1)
Option input (IN2)
Option input (IN3)
Option input (IN4)
Option input (IN5)
Option input (IN6)
Option input (IN7)
[ 20]
[ 21]
[ 22]
[ 23]
[ 24]
[ 25]
[ 26]
[ 27]
[ 28]
[ 29]
[in1]
[in2]
[in3]
[in4]
[in5]
[in6]
[in7]
[in8]
[in9]
[i10]
[
[
[
[
[
[
[
[
[
[
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
on] / [ oFF]
Option input (IN8)
Option input (IN9)
Option input (IN10)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
27
4. FUNCTION SETTINGS
4-8. Output checking method
This is used at the following times.
・When you would like to check for problems with the operation panel
・When you would like to check for a problem with the drive mechanism
・When you would like to check for broken cords
You can check whether the signals being output by the CPU are driving the mechanisms correctly.
2619B
1. While pressing the
The item number will appear in the PROGRAM No. display (2), and the item name will appear in the menu display (3).
2. Press the key (4) or the key (1) to select the desired item number.
3. For item numbers 51 to 54, press the or key (5) to check the operation.
* The operation for that check item will be carried out while the key is being pressed.
key (1), turn on the power switch.
4. For item numbers 55 onward, depress the foot switch to the 2nd step. (For a 2-pedal foot switch, depress the start
switch.)
* The operation for that check item will be carried out while the foot switch is being depressed.
5. When returning to normal operation, turn power off and then on again.
Item No.
[ 51]
Item name
Operation
When the
When the
When the
When the
When the
When the
key is pressed, the work clamp/button clamp will move to the left.
key is pressed, the work clamp/button clamp will move to the right.
key is pressed, the work clamp/button clamp will move forward.
key is pressed, the work clamp/button clamp will move back.
key is pressed, the work clamp/button clamp will lift.
key is pressed, the work clamp/button clamp will drop.
[PM−X]
[ 52]
[ 53]
[ 54]
[PM−y]
[PM−P]
[PM−n]
When you press the
When you press the
key, the thread nipper moves toward the home position.
key, the thread nipper moves toward the retract position.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
28
4. FUNCTION SETTINGS
Item No.
[ 55]
[ 56]
[ 57]
[ 58]
Item name
[CL−r]
[CL−L]
[Foot]
Operation
The valve for the right work clamp turns on. (*)
The valve for the left work clamp turns on. (*)
The valve for the stepping foot turns on. (*)
Inner clamping valve is turned ON (*)
[FLiP]
[ 59]
[CooL]
Needle cooler valve is turned ON. (*)
Panel indicators illuminate in sequence, and then the 7-segment display turns on one
digit at a time.
[ 60]
[7SEG]
Blank Æ 0 Æ 1 Æ 2 . . . . Æ 8 Æ 9 Æ 8. Æ Blank
Thread trimmer solenoid is turned ON for the specified period.
Remove the rear cover and check the operation.
The digital tension solenoid is turned ON for the specified period.
The external wiper solenoid is turned ON for the specified period. (*)
Option output 1 turns on. (*)
Option output 2 turns on. (*)
Option output 3 turns on. (*)
Option output 4 turns on.
Option output 5 turns on.
Option output 6 turns on.
Option output 7 turns on.
Option output 8 turns on.
Option output 9 turns on.
Option output 10 turns on.
Option output 11 turns on.
Option output 17 turns on.
Option output 18 turns on.
[ 61]
[ CUt]
[ 62]
[ 63]
[ 64]
[ 65]
[ 66]
[ 67]
[ 68]
[ 69]
[ 70]
[ 71]
[ 72]
[ 73]
[ 74]
[ 75]
[ 76]
[ 77]
[ 78]
[dtEn]
[ WiP]
[oP 1]
[oP 2]
[oP 3]
[oP 4]
[oP 5]
[oP 6]
[oP 7]
[oP 8]
[oP 9]
[oP10]
[oP11]
[oP17]
[oP18]
[oP19]
[oP20]
Option output 19 turns on.
Option output 20 turns on.
* Cannot be used with the KE-430F and BE-438F.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
29
4. FUNCTION SETTINGS
4-9. Confirming software version
2620B
1. If you turn on the power while pressing the
key (1), the software version will be displayed in the menu display (2).
2. The PROGRAM No. display (4) will change as follows each time the
or
key (3) is pressed.
PROGRAM No. display (4)
Software
Main control program
Motor control program
Panel control program
Main IPL
Menu display (2) example
[1.Mn]
[2.Mt]
[3.PL]
[4.in]
[5.it]
[1.0.00]
[1.00 ]
[1.00 ]
[1.00 ]
[1.00 ]
[1.00 ]
Motor IPL
Panel IPL
[6.iL]
3. Press the TEST key (5) to return to the normal display. The sewing machine will switch to home position detection standby.
KE-430F, BE-438F
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
4-10. Protection settings
There are two ways which can be used to switch to protect setting mode: Method A (which does not require an SD card) and
Method B (which requires an SD card).
If you want to set up the sewing machine so that these modes cannot be distinguished, it is recommended that you set the
method to Method B.
* If using an SD card, read the section titled “7-1. Notes on handling SD cards (commercially available)”.
● Method A
1. While pressing the RESET key (1) and the TEST key (2) and the ENTER key (3), turn on the power switch.
* The previous protection level (OFF, 1 to 7) will appear in the menu display (4).
* The protection level is set to OFF at the time of shipment from the factory.
2621B
* If a beeping sound is heard and “ Pr” “diFF” is displayed, it means that the method has been set to method B.
In this case, start by means of method B. (Refer to the next page.)
2. Press the
or
key (5) to select the protection level.
Nothing is disallowed.
Protection level
OFF
Details
1 – 6
Certain operations are disallowed depending on the protection level.
* Protected items have been preset for each level. Refer to “Table of protection levels
and corresponding protected items” on page 33.
7
You can change the protection setting for each of the 21 items individually.
* Set to ON (disallowed) or OFF (allowed) for each item.
* All items are set to OFF at the time of shipment from the factory.
3. Press the ENTER key (3) to store the protection level.
* If setting to a protection level other than level 7, proceed to step 4. If setting to level 7, proceed to step 5.
4. Press the TEST key (2).
* The display will return to the normal display and the sewing machine will change to home position standby.
5. The item number will appear in the PROGRAM No. display (6), and the setting (ON/OFF) will appear in the menu display
(4).
6. Press the
7. Press the
or
or
key (7) to select the item number (1 to 21). (Refer to page 33.)
key (5) to change the setting (ON/OFF).
8. Press the ENTER key (3) to store the setting (ON/OFF).
9. Repeat steps 6 to 8 above for each item, and then press the TEST key (2).
* The protect setting mode will be exited and the sewing machine will change to home position standby.
* If you would like to return to protection level setting (2 above), press the F1 key (8).
KE-430F, BE-438F
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
● Method B
Have an SD card ready.
* The SD card is only used at the step of selecting protect setting mode, so any type of SD card can be used as long as it
can be accessed. In addition, if making the setting two or more times, a different SD card from the one used before can be
used.
1. Insert the SD card, and then while pressing the RESET key (1) and the TEST key (2) and the ENTER key (3), turn on the
power switch.
* The previous starting method (A or b) will be displayed in the menu display.
* The method is set to A at the time of shipment from the factory.
2622B
2. Press the
or
key (5) to select the next starting method.
Starting method
Details
A
B
Protect setting mode can be started using either Method A or Method B.
Protect setting mode can only be started using Method B.
3. Press the ENTER key (3) to store the starting method.
4. For the method of operation from this point onward, refer to steps 2 to 9 in “Method A” (previous page).
KE-430F, BE-438F
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4. FUNCTION SETTINGS
Table of protection levels and corresponding protected items
× : Operation disallowed
Level
Item
No.
Protection
details
OFF
7 (Individual settings)
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Data
initialization
Memory switch
(Advanced)
Memory switch
(Standard)
<Home position,
upper
reference>
position
adjustment
×
×
×
×
×
×
×
1
2
3
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
shaft
×
4
×
5
6
Program No.
XY
enlarge
change during
wait (Possible if
100% or less)
XY
enlarge/reduce
change during
wait
×
×
×
7
Sewing speed
during wait
×
×
×
×
×
×
×
8
9
Slow
start
×
during wait
Work
clamp/button
×
×
×
×
10
clamp
height
during wait
Tension during
wait
×
×
×
11
12
Lower
thread
counter change
during wait
×
Production
counter
during wait
Lower
counter setting
mode
Production
counter setting
mode
clear
×
×
13
14
15
thread
×
×
Program setting
mode
Cycle program
setting mode
×
×
×
×
×
×
×
×
×
×
×
16
17
18
19
×
Pattern
data
×
editing mode
Data read/write
mode
×
Sewing
after
start
pause
using the STOP
switch (available
by special order)
Parallel
movement
mode
×
20
21
×
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
33
5. EDITING PATTERN DATA
5. EDITING PATTERN DATA
5-1. Tension information in pattern data
Tension codes are recorded in the pattern data to provide tension information.
The tension codes indicate the type of tension (T1 to T9).
In addition, the units which tension codes are divided into are called sections, and sequential numbers are assigned to them
starting from the first stitch. Up to a maximum of 99 sections are possible.
* The tension values for the tension codes are set in program mode for each program.
Example: Pattern No. 200
Final stitch
1st stitch
28th stitch
10th stitch
2nd stitch
2623B
Section <1>
Section <2>
Section <3>
Section <4>
Needle Drop No. <1>
Tension Code <T1>
Needle Drop No. <2>
Tension Code <T6>
Needle Drop No. <10>
Tension Code <T4>
Needle Drop No. <28>
Tension Code <T1>
Upper thread tension <75>
Upper thread tension <125> Upper thread tension <110>
Upper thread tension <75>
Example: When sewing program No. 900 into which pattern No. 200 has been programmed
Example: Editing in pattern editing mode
Pattern No. 200
Example: Program mode editing
Program No. 900
Needle Drop No.
1st stitch
Section No.
Tension Code
Pattern No.
X-scale
200
100
100
2700
Lo8
75
1
2
3
4
T1
T6
T4
T1
2nd stitch (to 9th stitch)
10th stitch (to 27th stitch)
28th stitch (to final stitch)
Y-scale
Sewing speed
Slow start pattern
Upper thread tension T1
Upper thread tension T4
Upper thread tension T6
110
125
Tension Code
* Of all the tension codes (T1 to T9), only the
tension codes which have been programmed
into pattern No. 200 will be displayed.
Section
No.
Final stitch
2624B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
34
5. EDITING PATTERN DATA
5-2. Work flowchart
2922B
KE-430F, BE-438F
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5. EDITING PATTERN DATA
5-3. Switching to pattern editing mode
While pressing the TEST key, press the
key.
1
・The pattern number will flash in the PROGRAM No.
display.
・The number of stitches remaining until the final stitch
will be displayed in the menu display.
・The section number will be displayed in the section
No. display. “. ” means the start of a section.
・The tension code will be displayed in the tension
display.
2626B 2627B
Press the
number.
or
key to select the desired pattern
2
* Only the pattern numbers which are currently
registered will be displayed.
2628B
Depress the foot switch to the 2nd step.
・Home position detection will be carried out.
・The pattern number will changed to illuminated.
3
2nd step
From this point on, the condition is referred to as pattern
editing mode.
4441Q
5-4. Checking pattern data
You can check the tension information (section numbers and tension codes) in pattern data.
Carry out steps 1 to 3 in “5-3. Switching to pattern editing
mode” to switch to pattern editing mode.
When you press the or key, the work clamp/button
1
clamp will move one stitch at a time.
・The section number and tension code and the number
of stitches remaining until the final stitch are displayed
at the current position.
While holding down the SELECT key, press the
SECTION [+ -] key to automatically move the work
clamp/button clamp to the beginning of a section.
+: Moves in the forward direction
-: Moves in the reverse direction
2629B 2630B
End pattern editing mode
Press the TEST key.
・The display will return to the normal display and the
sewing machine will change to home position standby.
2
2404B
TEST indicator switches off
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
36
5. EDITING PATTERN DATA
5-5. Copying pattern data
Editing (adding, changing or deleting) of the tension codes within pattern data is limited to pattern numbers within the range of
200 to 999.
Because of this, if you would like to edit pattern data which has already been registered, you will need to copy the pattern to a
number that is 200 or higher.
* If you would like to delete pattern data which has already been registered, this can be done using initialization mode. Refer
to “6-7. Resetting all settings to their defaults” in the CD Instruction Manual.
Carry out steps 1 to 3 in “5-3. Switching to pattern editing
mode” to switch to pattern editing mode.
1
Press the F1 key and the F4 key at the same time.
・The pattern number which is to be copied will be
displayed in the PROGRAM No. display.
・“Copy” will be displayed in the menu display.
・“ Pt” will be displayed in the section No. display.
・The pattern number for the copy destination will be
displayed in the tension display.
2631B 2632B
2
Press the TENSION (
) keys to select the
pattern number for the copy destination.
* Only patterns numbers which have not yet been
recorded will be displayed.
For example, if copying to
pattern No. 204.
2633B
To do the copying, press the ENTER key.
・The pattern will be copied and the sewing machine will
then return to pattern editing mode.
3
or
If you would like to return to pattern editing mode without
copying the pattern, press the RESET key.
2414B 2634B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
37
5. EDITING PATTERN DATA
5-6. Adding tension codes
<If adding a T5 code at the 5th stitch in section 2>
Final stitch
Final stitch
2639B
1
Carry out steps 1 to 3 in “5-3. Switching to pattern editing
mode” to switch to pattern editing mode.
Press the
or
key to move the work clamp/button
clamp to the desired position.
* Move it to a position other than the start of the section
(so that “.” is not displayed).
2635B 2636B
2
Press the TENSION (
desired tension code (T1 to T9).
) keys to select the
・The tension code will flash.
For example, tension code T5
2637B
To add a tension code, press the ENTER key.
3
・ A new tension code will be added and the sewing
machine will return to pattern editing mode. As well
as this, a section will be added and the numbers for
subsequent sections will be incremented by 1.
or
If you would like to return to pattern editing mode without
adding a tension code, press the
or
key.
or
If you would like to end pattern editing mode without
adding a tension code, press the TEST key.
2414B 2638B 2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
38
5. EDITING PATTERN DATA
5-7. Changing tension codes
<If changing T6 to T3 in section 2>
Final stitch
Final stitch
2642B
1
Carry out steps 1 to 3 in “5-3. Switching to pattern editing
mode” to switch to pattern editing mode.
While pressing the SELECT key, press the SECTION
[+ -] keys. Each time a key is pressed, the work
clamp/button clamp automatically moves to the start of
the next or the previous section.
Move the work clamp/button clamp to the start of the
section you would like to change.
2630B 2641B
2
Press the TENSION (
desired tension code (T1 to T9).
) keys to select the
・The tension code will flash.
For example, change the tension
code to T3 in section 2.
2640B
To change the tension code, press the ENTER key.
・The tension code will be changed and the sewing
machine will then return to pattern editing mode.
3
or
or
If you would like to return to pattern editing mode without
changing a tension code, press the
or
key.
If you would like to end pattern editing mode without
changing a tension code, press the TEST key.
2414B 2638B 2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
39
5. EDITING PATTERN DATA
5-8. Deleting tension codes
<Deleting section 2>
Final stitch
Final stitch
2647B
1
Carry out steps 1 to 3 in “5-3. Switching to pattern editing
mode” to switch to pattern editing mode.
While pressing the SELECT key, press the SECTION
[+ -] keys. Each time a key is pressed, the work
clamp/button clamp automatically moves to the start of
the next or the previous section.
Move the work clamp/button clamp to the start of the
section you would like to delete.
2630B 2641B
While pressing a TENSION key, press the RESET key.
The delete selection display will appear.
2
・The TEST indicator will turn off.
・“ dEL” will be displayed in the menu display.
2643B 2644B
When you press the SECTION [+ -] keys, the delete
selection display will switch between all sections and an
individual section.
3
For example, when an
individual section is selected
Tension code T6
For example, when all
sections are selected
2645B 2646B
To delete the section, press the ENTER key.
4
・ The specified tension code will be deleted and the sewing
machine will return to pattern editing mode. As well as
this, the section will also be deleted and the numbers
for subsequent sections will be decremented by 1.
* The tension code in section 1 is the only tension code
which cannot be deleted.
or
If you would like to return to pattern editing mode without
deleting the tension code, press the RESET key.
2414B 2634B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
40
6. X AND Y PARALLEL MOVEMENT OF SEWING PATTERNS
6. X AND Y PARALLEL MOVEMENT OF SEWING
PATTERNS
The work clamp/button clamp can be moved to any desired position so that sewing patterns which have already been
programmed can be moved in parallel directions forward, back or to the left or right.
Use this when you would like to correct the sewing position with respect to the work clamp/button clamp.
Press the
or
key to select the program number.
1
* If a cycle program has been selected, the following
operation cannot be carried out. Select a program
from 1 to 999.
For example, program
No. 1
2776B
While holding down the TEST key, press the
switch to parallel movement mode.
key to
2
・The amount of parallel movement in the horizontal
direction which has currently been set will be
displayed in the menu display in mm units.
* The sewing machine will not switch to parallel
movement mode if memory switch No. 465 is set to
“3”.
Set it to “1” or “2”.
2777B 2648B
Depress the foot switch to the 2nd step.
・Home position detection will be carried out.
・The pattern number will change to illuminated.
3
4
2nd step
4441Q
Each time the
or
key is pressed, the work
clamp/button clamp will move by 0.05 mm.
・In X-scale parallel movement mode, the work
clamp/button clamp will move to the left when the
key is pressed, and to the right when the
pressed.
key is
・The range of movement is a maximum of -9.95 mm to
+9.95 mm. However, the sewing pattern cannot be
moved outside the sewing area.
For example, set to 0.05.
2778B
2414B
Confirm the movement amount.
Press the ENTER key.
5
・The amount of parallel movement in the horizontal
direction will be confirmed, and the menu display will
change to illuminated.
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
41
6. X AND Y PARALLEL MOVEMENT OF SEWING PATTERNS
Press the SELECT key so that the Y-scale indicator
flashes.
6
Y-scale
X-scale
Parallel movement mode
Parallel movement mode
2401B
* When the SELECT key is pressed, the X-SCALE
indicator and the Y-SCALE indicator will flash
alternately.
2649B
7
Each time the
or
key is pressed, the work
clamp/button clamp will move by 0.05 mm.
・In Y-scale parallel movement mode, the work
clamp/button clamp will move forward when the
key is pressed, and backward when the
pressed.
key is
・The range of movement is a maximum of -9.95 mm to
+9.95 mm. However, the sewing pattern cannot be
moved outside the sewing area.
For example, set to -0.05.
2779B
2414B
Confirm the movement amount
Ending parallel movement mode
Press the ENTER key.
8
9
・The amount of parallel movement in the vertical
direction will be confirmed, and the menu display will
change to illuminated.
Press the TEST key.
・The display will return to the normal display and the
sewing machine will change to home position standby.
* If you would like to return to step 4, press the SELECT
key instead of the TEST key.
TEST indicator switches off
NOTE:
・If you change the program number, the pattern number, the X-scale or the Y-scale, the movement amount which has
been stored will be reset.
・When the power switch is turned off, the movement amount which has been stored will be reset. However, if memory
switch No. 465 is set to “2”, the movement amount will remain stored and will not be reset.
KE-430F, BE-438F
42
Download from Www.Somanuals.com. All Manuals Search And Download.
7. USING SD CARDS
7. USING SD CARDS
7-1. Notes on handling SD cards (commercially available)
•
•
•
•
•
•
Use an SD card or a multimedia card with a capacity of 2GB or less.
Do not disassemble or alter SD cards.
Do not bend, drop, scratch or place heavy objects on top of the SD cards.
Do not allow the SD cards to become wet, such as with water, oil, solvents, drinks or any other liquids.
Do not use or store the SD cards in a locations exposed to strong static electricity or electrical interference.
Do not use or store the SD cards in a locations exposed to vibrations or impacts, direct sunlight, extreme dust (or lint), high
temperatures, high humidity, severe temperature fluctuations, or strong magnetic forces (such as from speakers).
Do not subject the SD cards to vibration or shocks or remove them from the sewing machine while data reading or writing
is in progress.
•
•
Data on the SD cards may be lost or damaged due to some malfunction or accident. We recommend backing up important
data.
•
•
The SD cards that you purchased is already formatted. We recommend that the SD cards not be reformatted.
The recommended SD cards are those sold by SanDisk and Panasonic. Cards from other manufacturers may use different
formatting methods and may not work correctly as a result.
For additional information, refer to the instruction manual included with the SD cards that you have purchased.
* This product is compatible with SD cards that have been formatted using the FAT16/32 method. Cards that have
been formatted using other formatting methods cannot be used.
* All other company and product names mentioned in this instruction manual are trademarks or registered trademarks
of their respective companies. However, the explanations for markings such as TM are not clearly described within
the text.
7-2. Structure of an SD card folder
Data type
Folder name
\BROTHER\ISM\ISMSYS\
File name
ISM08MN.BVP (Main control program)
ISM08MT.BVP (Motor control program)
ISM08PL.BVP (Panel control program)
Control program
\BROTHER\ISM\ISMDA**\
* ‘**’ represents the value for memory switch No.
752. If storing additional pattern data from
other sewing machines in the same SD card,
change the name of the folder.
ISMS0***.sew
* ‘***’ represents the pattern data number.
Pattern data
Memory switch
Same as above
ISMMSW.SEW
Parameter
Same as above
Same as above
ISMUPG.SEW
ISMCYC.SEW
Cycle program
Error log
\BROTHER\ISM\ISMLDT\
Stores the files which relate to error logs.
KE-430F, BE-438F
43
Download from Www.Somanuals.com. All Manuals Search And Download.
7. USING SD CARDS
7-3. Preparation for reading and writing data
Insert the SD card into the SD slot.
1
NOTE:
•
•
Make sure the SD card is facing the correct way.
The cover should be closed at all times except when
the SD card is inserted and removed, otherwise dust
may cause trouble
2650B
Turn on the power switch.
2
3
While pressing the TEST key, press the ENTER key.
Switching to SD data read/write mode
2652B
・“ sd” will appear in the PROGRAM No. display and
“read” will appear in the menu display while the SD
card is being read.
・Once reading of the SD card is complete, the mode
number will appear in the PROGRAM No. display and
the setting for that mode number will appear in the
menu display.
・The initialization mode is additional pattern data read
mode. (Refer to “Read/write mode list” below.)
TEST indicator flashes
2651B
Press the
or
key to select the mode.
4
For example mode No. w2
2653B
[Read/write mode list]
PROGRAM No.
Menu display
Setting items
display
r 1
[-Ptn]
[Ptn-]
Reads additional pattern data from the SD card. *
w 2
r 3
Writes additional pattern data to the SD card.
[-MEM]
[MEM-]
[-PrG]
[PrG-]
Memory switch settings are read from the SD card.
Memory switch settings are written to the SD card.
w 4
r 5
Reads sewing program data and cycle program data from the SD card.
Writes sewing program data and cycle program data to the SD card.
w 6
Reads all sewing machine data (sewing program data, cycle program data, memory
switch settings and additional pattern data) from the SD card.
r 7
[-ALL]
Writes all sewing machine data (sewing program data, cycle program data, memory
switch settings and additional pattern data) to the SD card.
w 8
W9
[ALL-]
[LoG-]
Error log data is written to the SD card.
* The additional pattern data that can be used with this sewing machine is data which has been created for the
KE-430F/BE-438F or for the KE-430D/BE-438D.
KE-430F, BE-438F
44
Download from Www.Somanuals.com. All Manuals Search And Download.
7. USING SD CARDS
7-4. Reading additional pattern data
Select the “ r 1” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
・The number of the additional pattern data in the SD
card folder will appear in the tension display.
(The initial value displayed is “ALL”.)
2651B
2
Press the
or
key to select the number for the
additional pattern that you would like to be read (ALL,
200 to 999).
・When “ALL” is displayed, all of the additional pattern
data will be read at once.
For example, to read pattern
number 200
・The additional pattern numbers displayed will only be
those that are in the SD card folders. (If there is no
data on the card, “ALL” will be the only thing
displayed.)
2656B
Press the ENTER key.
3
2414B
・The buzzer will sound and the selected pattern data
will be read from the folder on SD card and copied into
the sewing machine’s memory.
While reading
・If no additional pattern data exists, an error buzzer will
sound.
Pattern number being read
appears in the tension display
2657B 2658B
When the display returns to the status in step 1, reading
of the additional pattern data is complete.
4
5
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2654B
Ending read/write mode
Press the TEST key.
* To sew a pattern that you want to add, register a
program while referring to “5-2. Program setting
method” in the CD Instruction Manual.
TEST indicator switches off
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
45
7. USING SD CARDS
7-5. Writing additional pattern data to an SD card
Select the “ w2” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
・The numbers for the additional pattern data in the
sewing machine memory will appear in the tension
display.
(The initial value displayed is “ALL”.)
2901B
2
Press the
or
key to select the number for the
additional pattern that you would like to write (ALL, 200
to 999).
・When “ALL” is displayed, all of the additional pattern
data will be read at once.
・The additional pattern numbers displayed will only be
those that are in the sewing machine memory. (If
there is no data in the memory, “ALL” will be the only
thing displayed.)
For example, writing pattern
number 200
2656B
Press the ENTER key.
3
2414B
・The buzzer will sound and the selected pattern data
will be written to the SD card.
・If no additional pattern data exists, an error buzzer will
sound.
While writing
Pattern number being written
appears in the tension display
2660B 2658B
When the display returns to the status in step 1, writing
of the additional pattern data is complete.
4
5
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2659B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
46
7. USING SD CARDS
7-6. Reading memory switch data
Select the “ r3” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2661B
Press the ENTER key.
2
2414B
・The buzzer will sound and the memory switch data will
be read from the SD card and stored in the sewing
machine memory, and the memory switch settings will
then be applied.
While reading
・If no memory switch data exists, an error buzzer will
sound.
“MEM” appears in the tension
display
2662B 2663B
When the display returns to the status in step 1, reading
of the memory switch data is complete.
3
4
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2661B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
47
7. USING SD CARDS
7-7. Writing memory switch data to the SD card
Select the “ w4” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2664B
Press the ENTER key.
2
2414B
・The buzzer will sound and the memory switch data will
be copied to the SD card.
While writing
“MEM” appears in the tension
display
2902B 2663B
When the display returns to the status in step 1, writing of
the memory switch data is complete.
3
4
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2664B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
48
7. USING SD CARDS
7-8. Reading program data
Select the “ r5” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2665B
Press the ENTER key.
2
2414B
・The buzzer will sound and the sewing program data
and cycle program data will be read from the SD card
and stored in the sewing machine’s memory, and the
sewing programs and cycle programs will then be set.
・If no program data or cycle program data exists, an
error buzzer will sound.
While reading
“PrG” appears in the tension
display
2903B 2668B
When the display returns to the status in step 1, reading
of the program data is complete.
3
4
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2665B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
49
7. USING SD CARDS
7-9. Writing program data to an SD card
Select the “ w6” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2666B
Press the ENTER key.
2
2414B
・The buzzer will sound and the memory switch data will
be copied to the SD card.
While writing
“PrG” appears in the tension
display
2667B 2668B
When the display returns to the status in step 1, writing of
the program data is complete.
3
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2666B
Ending read/write mode
Press the TEST key.
4
TEST indicator switches off
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
50
7. USING SD CARDS
7-10. Reading sewing machine data
Select the “ r7” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2669B
Press the ENTER key.
2
2414B
・The buzzer will sound and the sewing program data,
cycle program data, memory switch settings and
additional pattern data will be read from the SD card
and stored in the sewing machine's memory.
・If no program data or cycle program data exists, an
error buzzer will sound.
While reading
“MEM” appears in the tension
display while memory switch
settings are being read, the
pattern number appears while
additional pattern data is being
read, and “PrG” appears while
program data is being read
2670B 2663B
When the display returns to the status in step 1, reading
of the sewing machine data is complete.
3
4
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2669B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
51
7. USING SD CARDS
7-11. Writing sewing machine data to an SD card
Select the “ w8” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2671B
Press the ENTER key.
2
2414B
・The buzzer will sound and the sewing program data,
cycle program data, memory switch settings and
additional pattern data will be read from the SD card
and stored in the sewing machine's memory.
While writing
“MEM” appears in the tension
display while memory switch
settings are being written, the
pattern number appears while
additional pattern data is being
written, and “PrG” appears while
program data is being written
2672B 2663B
When the display returns to the status in step 1, writing of
the sewing machine data is complete.
3
4
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2671B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
52
7. USING SD CARDS
7-12. Writing error log data and memory switch log data to an SD card
Select the “ w9” SD data read/write mode.
(Refer to “7-3. Preparation for reading and writing data”.)
1
2673B
Press the ENTER key.
2
2414B
・The buzzer will sound and the error log data and
memory switch log data will be copied to the SD card.
While writing
“LoG” appears in the tension
display while log data is being
written
2674B 2675B
When the display returns to the status in step 1, writing of
the log data is complete.
3
4
・If you would like to use any other read/write modes,
press the
run it.
or
key to select the mode and then
2673B
Ending read/write mode
TEST indicator switches off
Press the TEST key.
2404B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
53
7. USING SD CARDS
7-13. Updating the control program version
Place the control program that you would like to update into the folder of the SD card as specified in “7-2. Structure of
a SD card folder”.
1
With the power switch turned off, insert the SD card into the SD card slot.
(Refer to step 1 in “7-3. Preparation for reading and writing data”.)
2
While holding down the RESET, TEST and ▲ keys, turn
on the power switch.
3
2677B
The same “bro”, “ther”, “-F” (may vary depending on
specifications) and “430” (“438” as appear in the
PROGRAM No. display, menu display, section No.
display and tension display will appear. Keep holding
down the keys until you hear a beep.
2676B
“1.Mn”will appear in the PROGRAM No. display and
“*.*.**” (control program version stored on the SD card)
will appear in the menu display.
4
2678B
Press the
updated.
or
key to select the program to be
5
PROGRAM No.
display
Menu
display
Control program
Main
[1.Mn]
[*.*.**]
Motor
Panel
[2.Mt]
[3.PL]
[*.**]
[*.**]
・If there is no program to be updated which is stored on
the SD card, “----” will appear in the menu display.
2679B
Press the ENTER key.
6
2414B
・The buzzer will sound and updating of the program
version will start.
・When “End” appears in the menu display, updating is
complete.
・To continue updating another program, return to step
5 and select the next program to be updated.
“WAIT” will appear in the menu
display and the value in the
tension display will increment
while the program version is
being updated.
2680B 2681B
Turn off the power switch.
7
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
54
8. MECHANICAL DESCRIPTIONS
8. MECHANICAL DESCRIPTIONS
The mechanisms operate in the order of the numbers given in the illustrations.
* <number> and [number] indicates the flow of each operations given.
* (number) indicates part names only. (They do not represent the flow of operations.)
8-1. Needle bar and thread take-up mechanisms
2523B
1. Pulley
2. Upper shaft
3. Thread take-up crank
4. Needle bar crank
5. Needle bar connecting <5> Thread take-up
rod assembly
6. Needle bar clamp
7. Needle bar
lever assembly
8-2. Lower shaft and shuttle race mechanisms
2524B
1. Pulley
2. Upper shaft
3. Crank rod assembly
4. Rock gear
5. Lower gear
6. Lower shaft assembly
7. Driver
8. Shuttle hook
KE-430F, BE-438F
55
Download from Www.Somanuals.com. All Manuals Search And Download.
8. MECHANICAL DESCRIPTIONS
8-3. Work clamp lifter mechanism
1. Pulse motor T assembly
2. Gear 16
3. Cam gear
4. Driving lever
5. Link
6. Lifter lever assembly
7. Work clamp lifter plate assembly
8. Work clamp arm lever plate
9. Work clamp arm lever shaft
10. Work clamp arm lever
11. Work clamp
2525B
* When the work clamp pulse motor is turned off, the work
clamp lifter plate rises, and work clamps lower.
2526B
BE-438F
7. Button clamp rod
8. Button clamp lever
9. Button clamp holder hook assembly
10. Button clamp holder shaft
* When the work clamp pulse motor is turned off, the button
clamp rod rises, and button clamps lower.
11. Button clamp
KE-430F, BE-438F
56
Download from Www.Somanuals.com. All Manuals Search And Download.
8. MECHANICAL DESCRIPTIONS
8-4. Thread wiper mechanism
When the work clamp pulse motor is turned off, the
thread wiper operates in the opposite direction.
2527B
1. Pulse motor T assembly
2. Gear 16
3. Cam gear
4. Cam shaft
5. Thread wiper cam
6. Thread wiper driving lever
7. Thread wiper rod assembly
8. Connecting plate
9. Thread wiper arm assembly
KE-430F, BE-438F
57
Download from Www.Somanuals.com. All Manuals Search And Download.
8. MECHANICAL DESCRIPTIONS
8-5. Feed mechanism
Sewing patterns are created through combinations of X and Y movements.
X direction
2528B
1. Pulse motor X assembly
2. Feed gear
3. X-feed gear
4. X-feed lever
5. Regulator block assembly
6. Feed bracket sub assembly
Y direction
2529B
1.Pulse motor Y assembly
2.Feed gear
3.Y-feed rack shaft
4.Y-feed rack shaft clamp
5.Feed bracket sub assembly
KE-430F, BE-438F
58
Download from Www.Somanuals.com. All Manuals Search And Download.
8. MECHANICAL DESCRIPTIONS
8-6. Thread trimmer mechanism
2530B
1. Upper shaft
13. Thread trimmer lever H
2. Pulse motor T assembly
3. Gear 16
4. Cam gear
(1) Fixed knife
14. Thread trimmer rod H assembly <14>Thread trimmer link
15. Movable knife lever
16. Movable knife connecting plate
17. Movable knife
5. Cam shaft
6. Thread trimmer driving cam
7. Cam lever thread trimmer
8. Thread driving lever
9. Thread trimmer collar
10. Thread trimmer cam
11. Thread trimmer rod V assembly
12. Thread trimmer lever V
<Pulse motor ON>
18. Gear
<Thread trimmer solenoid ON>
[18] Thread trimmer solenoid assembly
[19] Thread trimmer link
[20] Thread trimmer rod H assembly
[21] Movable knife lever
19. Thread trimmer driving cam
20. Cam lever thread trimmer
21. Thread trimmer collar
[22] Movable knife connecting plate
[23] Movable knife
KE-430F, BE-438F
59
Download from Www.Somanuals.com. All Manuals Search And Download.
8. MECHANICAL DESCRIPTIONS
8-7. Tension release mechanism
1. Tension solenoid
2. Bolt
2531B
3. Tension release bar
4. Tension release pin
8-8. Thread nipper mechanism (KE-430F -03, -0F, -0K specifications only)
2532B
1. Pulse motor P assembly
2. Motor lever
3. TR-link
4. Thread driving lever
5. Connecting plate R
6. TN-Connecting plate assembly F
7. Thread nipper D assembly
8. Thread nipper U
KE-430F, BE-438F
60
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9. DISASSEMBLY
CAUTION
When replacing parts and installing optional
accessories, be sure to use only genuine Brother
parts.
Brother will not be held responsible for any
accidents or problems resulting from the use of
non-genuine parts.
Disassembly should only be carried out by a
qualified technician.
Turn off the power switch before disassembly,
otherwise the machine may operate if the foot switch
is depressed by mistake, which may result in injury.
Be sure to wear protective goggles and gloves when
handling the lubricating oil and grease, so that they
do not get into your eyes or onto your skin,
otherwise inflammation can result.
Furthermore, do not drink the oil or eat the grease
under any circumstances, as they can cause
vomiting and diarrhea.
If any safety devices have been removed, be
absolutely sure to re-install them to their original
positions and check that they operate correctly
before using the machine.
To prevent accidents and problems, do not modify
the machine yourself.
Brother will not be held responsible for any
accidents or problems resulting from modifications
made to the machine.
Keep the oil out of the reach of children.
Disassemble each part in order of the numbers.
9-1. Covers
2533B
7. Bolts [2 pcs]
8. Eye guard assembly
9. Screws [3 pcs]
10. Face plate assembly
11. Shoulder screws 8-2 [2 pcs]
12. Washer, wave springs [2 pcs]
13. Shuttle race cover assembly
1. Screws [4 pcs]
2. Top cover
3. Screws [4 pcs]
4. Rear cover
5. Screws [4 pcs]
6. Side cover
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
61
9. DISASSEMBLY
9-2. Work clamp arm mechanism
KE-430F
1. Set screw
2. Needle
3. Needle bar thread guide
4. Bolts [2 pcs]
5. Plain washers [2 pcs]
6. Work clamp arm assembly
7. Screws [2 pcs]
8. Feed plate
2534B
BE-438F
2535B
1. Set screw
5. Set screws [2 pcs: Loosen]
2. Needle
3. Needle bar thread guide
4. Nuts [2 pcs]
6. Button clamp holder shaft
7. Button clamp holder
8. Screws [2 pcs]
9. Feed plate
Adjusting screw
Compression spring [Push upward and remove horizontally]
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
62
9. DISASSEMBLY
9-3. Needle bar mechanism
2536B
Left-hand thread
2537B
Do not remove the slide block guide if
possible to prevent the machine from
overheating due to needle bar rubbing.
1. Rubber cap
11. Screw [Loosen]
2. Screw
12. Needle bar connecting rod assembly
13. Rubber cap
14. Set screws [3 pcs: Loosen]
15. Needle bar crank
16. Washer
17. Thread take-up lever assembly
18. Washer
19. Bolts [2 pcs]
3. Needle bar [Pull out]
4. Needle bar clamp
5. Slide block
6. Rubber caps [3 pcs]
7. Set screws [2 pcs: Loosen]
8. Set screws [2 pcs: Loosen]
9. Thread take-up support
10. Set screw collar
20. Slide block guide
KE-430F, BE-438F
63
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9-4. Upper shaft mechanism
2538B
1. Screws [2 pcs]
2. Grease support F
3. Bolt
4. Crank rod washer
5. Crank rod base
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
64
9. DISASSEMBLY
If the motor assembly cannot be
removed, insert the bolts 23 into these
two tapping holes and gradually tighten
them to remove the motor assembly.
Be careful not to drop the balancer.
(Remove)
(Loosen)
2539B
6. Screw
17. Set screws [2 pcs: Loosen]
18. Set screws [2 pcs: Loosen]
19. Screws [2 pcs]
20. Plain washers [2 pcs]
21. Bobbin winder unit
22. Set screws [2 pcs: Loosen]
23. Bolts [4 pcs]
7. Set screw [Loosen]
8. Thread take-up crank
9. Bolts [2 pcs]
(Remove one, loosen one.)
10. Balancer plate
11. Balancer
12. Set screws [2 pcs: Loosen]
13. Rubber cap
14. Set screws [2 pcs: Loosen]
15. Set screws [2 pcs: Loosen]
16. Set screws [2 pcs: Loosen]
24. Motor assembly
25. Thread trimmer cam
26. Joint assembly
27. Upper shaft
28. Pulley gear R
KE-430F, BE-438F
65
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9-5. Lower shaft mechanism
2540B
If the adjusting stud 3 will not pull
out, screw a M3 or similar screw (1)
into the tap hole and then pull on the
M3 or similar screw (1) so that the
adjusting stud 3 can be removed.
1. Bolt [Loosen]
2. Driver
3. Adjusting stud [Pull out]
4. Set screw [Loosen]
5. Screw
6. Oil tube support
7. Screw
8. Cord holder U3
9. Shuttle race base assembly
Do not remove the gear cover if at all
possible, otherwise grease will leak out.
2541B
10. Screws [5 pcs]
11. Gear cover
12. Screws [2 pcs]
13. Positioning plate
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
66
9. DISASSEMBLY
2547B
The rubber seal and the oil seal cannot be reused, so have new parts ready for use.
2549B
14. Rubber caps [2 pcs]
22. Lower shaft assembly
15. Set screws [4 pcs: Loosen]
16. Set screws [2 pcs]
17. Set screws [2 pcs]
18. Rock gear shaft R [Pull backward]
19. Rock gear shaft assembly [Pull forward]
20. Rock gear
23. Rubber seal L
24. Bearing bush assembly
(Tap out the rubber seal L 23 and the bearing bush
together toward the rear.)
25. Oil seal
26. Bearing bush assembly
(Tap out the oil seal 25 and the bearing bush
together toward the front.)
21. Set screws [4 pcs: Loosen]
KE-430F, BE-438F
67
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9-6. Lubrication
2542B
1. Bolts [2 pcs]
2. Bolts [2 pcs]
3. Plain washers [2 pcs]
4. Oil tank plate
5. Oil tank nut
6. Oil tank assembly
KE-430F, BE-438F
68
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9-7. Feed mechanism
2543B
1. Set screw [Loosen]
2. Retaining ring, E
3. Y-feed rack shaft cramp [Pull upward]
4. Screws [6 pcs]
5. Feed bracket cover
6. Set screw [Loosen]
7. Regulator block assembly
8. Feed bracket sub assembly
9. Bolts [4 pcs]
2544B
10. Feed bracket support plate
11. Bolt sockets (S/P washers) [3 pcs]
12. Y-motor setting plate [Pulse motor Y assembly]
13. Y-feed rack shaft
14. Bolt
15. X-feed gear
16. Bolt sockets (S/P washers) [3 pcs]
17. X-motor setting plate [Pulse motor X assembly]
18. X-feed lever [Pull upward]
2545B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
69
9. DISASSEMBLY
9-8. Thread wiper mechanism
2546B
1. Set screw [Loosen]
2. Retaining ring, E
3. Screws [2 pcs]
4. Plain washers [2 pcs]
5. Thread wiper arm assembly
6. Retaining ring, E
7. Plain washer
8. O rings [2 pcs]
9. Connecting plate [Pull upward]
10. Set screw [Loosen]
11. Retaining ring, E
12. Plain washer
13. Wiper shaft
14. Thread wiper rod assembly [Pull forward]
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
70
9. DISASSEMBLY
9-9. Work clamp lifter mechanism
2548B
1. Link shoulder screw
2. Bolts [3 pcs]
11. Cam lever thread trimmer
12. Plain washer
21. Thread wiper driving lever
22. Plain washer
3. Motor bracket assembly
4. Bolts [4 pcs]
13. Springs [2 pcs]
14. Bolts [2 pcs]
23. Set screws [2 pcs: Loosen]
24. Set screw collar
5. Pulse motor T assembly
6. Set screws [2 pcs: Loosen]
7. Gear 16
8. Set screws [2 pcs: Loosen]
9. Retaining ring, E
15. Spring hook
25. Set screws [6 pcs: Loosen]
26. Cam shaft
27. Cam gear
28. Thread wiper cam
29. Thread trimmer driving cam
16. Set screws [2 pcs: Loosen]
17. Retaining ring, E
18. Lever shaft
19. Drive lever w-clamp lifter
20. Plain washer
10. Driving thread trimmer shaft
(Continued on next page.)
KE-430F, BE-438F
71
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
KE-430F
30. Rubber cap
31. Link shoulder screw
32. Link
33. Set screw [Loosen]
34. Retaining ring, E
35. Lever shaft
36. Plain washer
37. Lifter lever assembly
38. Needle bar guide slide block
39. Work clamp lifter plate assembly
NOTE:
Hold the work clamp lifter plate
when removing the lifter lever
assembly 37, otherwise the work
clamp lifter plate assembly may fall
down.
2550B
BE-438F
30. Rubber cap
31. Link shoulder screw
32. Link
33. Set screw [Loosen]
34. Retaining ring, E
35. Lever shaft
36. Plain washer
37. Lifter lever assembly
38. Needle bar guide slide block
39. Nuts [2 pcs]
40. Button clamp roller shaft
41. Plain washer
42. Roller
43. Button clamp rod [Pull upward]
44. Set screw [Loosen]
45. Button clamp lever shaft [Pull out]
46. Retaining ring, E
47. Plain washer
48. Button clamp lever
49. Bolts [2 pcs]
50. Button clamp lever holder
2551B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
72
9. DISASSEMBLY
9-10. Threading mechanism
2552B
1. Set screw [Loosen]
2. Tension bracket [Pull out]
3. Tension release pin
4. Nut
5. Plain washer
6. Set screw [Loosen]
7. Tension stud assembly [Pull out]
8. Thread take-up spring
9-11. Tension release mechanism
1. Screws [2 pcs]
8. Solenoid setting plate
2. Solenoid cover
9. Bolt
3. Screws [2 pcs]
10. Nut
4. Tension solenoid
5. Bolts [2 pcs]
6. Spring washers [2 pcs]
7. Plain washers [2 pcs]
11. Plain washer
12. Solenoid cushion
13. Tension release bar
2553B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
73
9. DISASSEMBLY
9-12. Thread nipper mechanism (KE-430F -03, -0F, -0K specifications only)
2554B
1. Link shoulder screws [2 pcs]
2. TR-Ling
3. Set screws [2 pcs: Loosen]
4. Motor lever
17. Washers [2 pcs]
18. TN-connecting plate R
19. TN-connecting plate F assembly
20. Shoulder screw
5. Bolts [4 pcs]
6. Pulse motor P assembly
7. Bolts [3 pcs]
21. Thread nipper D assembly
22. Collar
23. Spacer
8. Motor bracket rear assembly
9. Link shoulder screw
10. Washer, wave spring
11. Set screws [2 pcs: Loosen]
12. Thread nipper lever shaft
13. Retaining ring, E
14. Washer
24. Shoulder screw, 6-0.9
25. Thread nipper U
26. Spring
27. Screws [2 pcs]
28. Plain washers [2 pcs]
29. Spring hook plate
30. Set screw [Loosen]
31. Eccentric shaft
2584B
15. Thread nipper lever
16. Bolts [2 pcs]
(The ball bearing (1) can be removed at the same time.)
KE-430F, BE-438F
74
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9-13. Thread trimmer mechanism
2555B
1. Set screws [2 pcs: Loosen]
2. Thread trimmer cam
3. Screws [3 pcs]
4. Fan
5. Set screws [2 pcs: Loosen]
6. Guide shaft
7. Spring
8. Nut
9. Shoulder screw B
10. Driving lever
11. Set screws [2 pcs: Loosen]
12. Retaining ring, C
13. Collar shaft
14. Thread trimmer collar
15. Screws [2 pcs]
16. Flat screws [2 pcs]
17. Needle plate
2556B
(Continued on next page.)
KE-430F, BE-438F
75
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
2557B
18. Nut
19. Shoulder screw B
20. Thread trimmer rod V assembly 35. Nut
33. Thread trimmer lever V
34. Washer, wave spring
47. Thread trimmer rod H assembly
48. Movable knife shoulder screw
49. Thrust washer
21. Nut
36. Solenoid shaft
50. Movable knife collar
51. Movable knife assembly
52. Movable knife spacer
53. Screws [2 pcs]
22. Shoulder screw B
23. Washer, wave spring
24. Bolt
37. Thread trimmer link
38. Set screws [2 pcs: Loosen]
39. Bolts [3 pcs]
25. Spring washer
40. Thread trimmer solenoid assembly 54. Spring washers [2 pcs]
26. Plain washer
41. Shoulder screw
55. Plain washers [2 pcs]
27. Set screws [2 pcs: Loosen]
28. Thread trimmer lever shaft
29. Retaining ring, C
30. Washers [2 pcs]
31. Thread trimmer lever H
32. Link shoulder screw
42. Connecting plate 6-1.8
43. Set screw [Loosen]
44. Movable knife lever shaft
45. Shoulder screw 6.35-6
46. Movable knife lever
56. Fixed knife
* 57. Screws [2 pcs] [KE-430F only]
* 58. Spring washers [2 pcs] [KE-430F only]
* 59. Plain washers [2 pcs] [KE-430F only]
* 60. Bobbin thread clamp spring [KE-430F only]
For the BE-438F, parts marked with * are supplied as accessories. Install
them if necessary.
KE-430F, BE-438F
76
Download from Www.Somanuals.com. All Manuals Search And Download.
9. DISASSEMBLY
9-14. Shuttle hook mechanism
2558B
1. Bobbin case assembly
2. Shuttle race base setting claw
[Open to right and left]
3. Shuttle race base
4. Shuttle hook
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
77
10. ASSEMBLY
10. ASSEMBLY
CAUTION
When replacing parts and installing optional
accessories, be sure to use only genuine Brother
parts.
Brother will not be held responsible for any
accidents or problems resulting from the use of
non-genuine parts.
Disassembly should only be carried out by a
qualified technician.
Turn off the power switch before disassembly,
otherwise the machine may operate if the foot switch
is depressed by mistake, which may result in injury.
Be sure to wear protective goggles and gloves when
handling the lubricating oil and grease, so that they
do not get into your eyes or onto your skin,
otherwise inflammation can result.
Furthermore, do not drink the oil or eat the grease
under any circumstances, as they can cause
vomiting and diarrhea.
If any safety devices have been removed, be
absolutely sure to re-install them to their original
positions and check that they operate correctly
before using the machine.
To prevent accidents and problems, do not modify
the machine yourself.
Brother will not be held responsible for any
accidents or problems resulting from modifications
made to the machine.
Keep the oil out of the reach of children.
Assemble each part in order of the numbers.
* (number) indicates part names only. (The numbers do not indicate the order of assembly.)
* Apply grease to the required places when reassembling the parts and once every two years.
10-1. Thread trimmer mechanism (1)
Apply grease to the portions indicated by the white arrows.
When the ball joint assembly of the thread
trimmer rod assembly has been
disassembled, assemble it so that the distance
between the centers of the holes is 290.1 ± 0.5
mm.
Tighten the set screw 5 on the screw stop
while lightly pressing the thread trimmer
lever shaft.
H
2
2831B
1. Movable knife lever
2. Thread trimmer rod H assembly
3. Shoulder screw 6.35-6
4. Movable knife lever shaft
5. Set screw (Tighten)
6. Thread trimmer lever H
7. Washer, wave spring
8. Shoulder screw B
9. Nut
10. Thread trimmer lever V
11. Washers [2 pcs]
12. Button clamp holder shaft
13. Retaining ring, C
14. Set screws [2 pcs: Tighten]
Tighten the two set screws 14 on the screw
stop while lightly pressing the thread trimmer
lever shaft.
2832B
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
78
10. ASSEMBLY
Tighten the two set screws 19 on
the screw stop while lightly
pressing the collar shaft 17 in the
direction shown in the illustration.
Check that the thread trimmer
collar 16 turns smoothly.
Apply grease.
2833B
Push the thread
trimmer solenoid
assembly 38 downward
gently to install it.
2834B
When the ball joint assembly of the
thread trimmer rod V assembly 20
has been disassembled, assemble
it so that the distance between the
centers of the holes is 309.5 ± 0.5
mm.
15. Driving lever
16. Thread trimmer collar
17. Collar shaft
18. Retaining ring, C
19. Set screws [2 pcs: Tighten]
20. Thread trimmer rod V assembly
21. Shoulder screw B
22. Nut
28. Plain washer
29. Spring washer
30. Bolt
31. Thread trimmer link
32. Solenoid shaft
33. Set screws [2 pcs: Tighten]
34. Thread trimmer link
35. Washer, wave spring
36. Link shoulder screw
37. Nut
23. Guide shaft
24. Spring
25. Set screws [2 pcs: Tighten]
26. Shoulder screw B
27. Nut
38. Thread trimmer solenoid assembly
39. Bolts [3 pcs]
40. Connecting plate
41. Shoulder screw, 6-1.8
2835B
KE-430F, BE-438F
79
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-2. Tension release mechanism
Adjust while referring to “11-16.
Adjusting the tension release amount”.
1. Tension release bar
2. Tension solenoid
3. Solenoid setting plate
4. Plain washers [2 pcs]
5. Spring washers [2 pcs]
6. Bolts [2 pcs]
9. Nut
10. Bolt
11. Screws [2 pcs]
12. Solenoid cover
13. Screws [2 pcs]
7. Solenoid cushion
8. Plain washer
2836B
10-3. Threading mechanism
While gently pushing the tension stud assembly 3
in the direction shown in the illustration, tighten the
set screw 6 until there is no clearance between the
tension bracket 1 and the nut 5.
1. Tension bracket
2. Thread take-up spring
3. Tension stud assembly
4. Plain washer
2837B
5. Nut
6. Set screw [Tighten]
7. Tension release pin
8. Set screw [Tighten]
Adjust the thread take-up spring height while
referring to “11-1-2. Thread take-up spring”.
KE-430F, BE-438F
80
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-4. Thread wiper mechanism
Apply grease to the portions indicated by the white arrows.
Gently push the wiper shaft 2 while
tightening the set screw 5.
Adjust while referring to “11-15.
Adjusting the thread wiper”.
少量
2838B
1. Thread wiper rod assembly [Insert from the front]
2. Wiper shaft
3. Plain washer
4. Retaining ring, E
5. Set screw [Tighten]
6. O rings [2 pcs]
7. Connecting plate
8. Plain washer
9. Retaining ring, E
10. Thread wiper arm assembly
11. Plain washers [2 pcs]
12. Screws [2 pcs]
13. Retaining ring, E
14. Set screw [Tighten]
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
81
10. ASSEMBLY
10-5. Thread nipper mechanism
Apply grease to the portions indicated by the white arrows.
Set so that the hole (4) in the needle hole
plate is near the center of the hole in the
thread nipper D assembly (3), and also set so
that the screw stop of the pulse motor P
assembly 26 is facing the same way as the
harness connector (5); then tighten the two
set screws 31.
Screw stop
2839B
1. Eccentric shaft (Install the ball bearing (2) at the same time.)
2. Set screw [Tighten]
18. Bolts [2 pcs]
3. Spring hook plate
19. Lever shaft
4. Plain washers [2 pcs]
20. Washer
21. Retaining ring, E
22. Thread nipper lever
23. Set screws [2 pcs: Tighten]
5. Screws [2 pcs]
6. Spring extension
7. Thread nipper U
8. Shoulder screw, 6-0.9
24. Washer, wave spring
9. Thread nipper spacer
25. Link shoulder screw
10. Thread nipper collar
26. Pulse motor P assembly
11. Thread nipper D assembly
27. Bolts [4 pcs]
2900B
12. Thread nipper shoulder screw
28. Motor lever
1) Loosen the set screw 2 about 1/3 of a turn
from its fully-tightened position so that the
eccentric shaft 1 can rotate.
2) Insert the Y-feed rack shaft (1), and then
turn the eccentric shaft 1 so that it is lightly
touching the ball bearing (2); then tighten
the set screw 2.
13. TN-connecting plate F assembly
29. TR-Link
14. TN-connecting plate R
30. Link shoulder screws [2 pcs]
31. Set screws [2 pcs: Tighten]
15. Bolts [3 pcs]
16. Motor bracket rear assembly
17. Washers [2 pcs]
3) Temporarily remove the Y-feed rack shaft
(1).
KE-430F, BE-438F
82
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-6. Work clamp lifter mechanism
Apply grease to the portions indicated by the white arrows.
* Refer to the next page for the points to note during reassembly.
D on next page
B on next page
Set so that the worn surface is on the inside, and align with
the screw stop. Tighten the two set screws 10 so that there is
no play in the axial direction. Check that the cam shaft 7
rotates smoothly.
A on next page
C on next page
C, D on next page
A on next page
B, D on next page
2840B
1. Spring hook
11. Plain washer
21. Retaining ring, E
2. Bolts [2 pcs]
3. Springs [2 pcs]
12. Thread wiper driving lever
13. Plain washer
22. Set screws [2 pcs: Tighten]
23. Gear 16
4. Cam gear
14. Drive lever w-clamp lifter
15. Lever shaft
16. Retaining ring, E
17. Set screws [2 pcs: Tighten]
18. Plain washer
19. Cam lever thread trimmer
20. Driving thread trimmer shaft
24. Pulse motor T assembly
25. Set screws [2 pcs: Tighten]
26. Bolts [4 pcs]
27. Motor bracket assembly
28. Bolts [3 pcs]
5. Thread wiper cam
6. Thread trimmer driving cam
7. Cam shaft
8. Set screws [6 pcs: Tighten]
9. Set screw collar
10. Set screws [2 pcs: Tighten]
29. Link shoulder screw
(Continued on next page.)
KE-430F, BE-438F
83
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
Set so that the clearance between
drive gear 16 23 and the edge of the
pulse motor T assembly 24 is 0.5 mm.
Reference line
Align
(Screw stop side)
2841B
2863B
Set the first two set screws 25 in the
clockwise direction to the screw stop
position.
Set the first set screws 8 and 10 in the clockwise
direction to the screw stop position.
The cam gear 6 also has a slot c in it, so make sure the correct hole is used.
Motor bracket
Align the positions of hole a in the cam gear
6 and hole b in the motor bracket 27.
2864B
2842B
Make sure the harness connector is
facing the correct way.
2865B
1) While maintaining the condition in C, install drive gear 16 23 to the motor bracket 27 so that the index
mark is facing directly upward. Make sure that the harness connector is facing the correct way at this
time.
2) Engage drive gear 16 23 and the cam gear 6, and while taking up the backlash (play), install the pulse
motor T assembly 24.
(Continued on next page.)
KE-430F, BE-438F
84
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
KE-430F
30. Work clamp lifter plate assembly
31. Needle bar guide slide block
32. Lifter lever assembly
33. Plain washer
34. Lever shaft
35. Retaining ring, E
36. Set screw [Tighten]
37. Link
38. Link shoulder screw
39. Rubber cap
BE-438F
2843B
30. Button clamp lever holder
31. Bolts [2 pcs]
32. Button clamp lever
33. Plain washer
34. Button clamp lever shaft
35. Retaining ring, E
36. Set screw [Tighten]
37. Button clamp roller shaft
38. Roller
39. Button clamp roller shaft
40. Plain washer
41. Nuts [2 pcs]
42. Needle bar guide slide block
43. Lifter lever assembly
44. Plain washer
45. Lever shaft
46. Retaining ring, E
47. Set screw [Tighten]
48. Link
49. Link shoulder screw
50. Rubber cap
2844B
Align the set screw 36 (430F) or 47 (438F) with the screw stop on the
lever shaft 34 (430F) or 45 (438F), and then tighten the set screw while
gently pushing the lifter lever assembly 32 (430F) or 43 (438F) so that
there is no play in it.
Check that the lifter lever assembly 32 (430F) or 43 (438F) moves
smoothly.
NOTE:
When the work clamp lifter plate assembly 30 (430F)/button clamp rod 37
(438F) is lowered, the needle bar guide slide block 31 (430F) or 42
(438F) moves away, so hold the work clamp lifter plate assembly 30
(430F)/button clamp rod 37 (438F) in place until the link shoulder screw
38 (430F) or 49 (438F) is tightened.
2845B
KE-430F, BE-438F
85
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-7. Feed mechanism
Apply grease to the portions indicated by the arrows.
Set so that the clearance between
the feed gear 1 and the pulse motor
X assembly 2 is 0.5 mm, and then
align the two set screws 3 with the
screw stops as shown in the
illustration and tighten them.
Grease
Screw stop
2866B
Apply grease to the grease hole on the inside.
2846B
2847B
2848B
Adjust the X-motor setting plate 2 so that the
backlash amount (play) of the feed gear 1 is 0 to
0.05 mm, and then tighten the bolts with washer 4.
Make sure that the harness faces correctly.
Index marks
1. Feed gear
2. X-motor setting plate [Pulse motor X assembly]
3. Set screws [2 pcs: Tighten]
4. Bolt sockets (S/P washers) [3 pcs]
5. X-feed lever
6. X-feed gear
7. Bolt
2849B
Engage the feed gear 1 and the X-feed gear 6 so that the
index marks are as close together as possible, and then
tighten the bolt 7 so that the gears move smoothly in the
axial direction with no play.
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
86
10. ASSEMBLY
Set screw
Grease
Remove the set screw and
apply grease, and then
retighten the set screw.
8. Y-feed rack shaft
2851B
9. Retaining ring, E
10. Feed bracket support plate
11. Bolts [4 pcs: Temporarily tighten]
12. Feed bracket sub assembly
13. Regulator block assembly
14. Set screw
15. Feed bracket cover
16. Screws [6 pcs]
17. Y-feed rack shaft cramp
18. Bolt
2852B
Move the feed bracket sub assembly 12 back and forth so that the Y-feed rack
shaft 8 and the feed bracket sub assembly 12 move smoothly, and then tighten
the four bolts 11.
(Continued on next page.)
KE-430F, BE-438F
87
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
Align the set screw 21 with the screw
stop and tighten it so that the
clearance between the feed gear 1
and the pulse motor Y assembly 20 is
0.5 mm as shown in the illustration.
Screw stop
2846B
2847B
19. Feed gear
20. Pulse motor Y assembly (Y-motor setting plate)
21. Set screws [2 pcs]
2853B
22. Bolt sockets (S/P washers)
[3 pcs: Temporarily tighten]
Make sure that the harness faces correctly.
1) Provisionally tighten the three bolts with
washer 22 so that the distance shown in the
illustration is 95 mm with the screw stop of the
pulse motor Y assembly 20 is facing the same
way as the harness connector.
Harness
connector
2) Move the pulse motor Y assembly 20 up or
down so that the Y-feed rack shaft 8 moves
with a force of 16 to 22 N, and then tighten the
three bolts with washer 22.
Screw stop
* For the BE-438F, be particularly careful that the
mechanism is in the correct position shown in
the illustration.
Approx. 95 mm
2854B
After installing, carry out the steps in "Feed mechanism home position adjustment"
on the following page.
(Continued on next page.)
KE-430F, BE-438F
88
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
<Feed mechanism home position adjustment>
2855B
2856B
1. Install the home position standard plate (1) to the feed bracket sub assembly (2) with the two screws (3).
2. Gently tilt back the machine head.
3. Switch the sewing machine to home position adjustment mode. (See "11-18-1. X- and Y-feed motor home positions".)
4. Press and hold the RESET key (4) for 2 seconds or more.
* The offset value will be cleared and reset to " 0".
4640Q
2857B
2858B
5. Turn the pulley by hand in the direction of the arrow and check at what point the needle drops to the home position
standard plate. If the needle does not drop to point (A), carry out the following adjustments.
NOTE:
Be careful not to let the needle touch the home position standard plate.
6. Loosen the bolt (5) and move the home position standard plate (1) to the left or right to adjust so that the needle drops to
point A.
* If play occurs in the axial direction, tighten the M6 or similar bolt (7) on the X-feed lever (6), and adjust while pulling the
M6 or similar bolt (7).
7. Tighten the bolt (5).
8. Turn off the power switch and check that there is no play in the X-feed gear (8) in the axial direction.
9. Make fine adjustments while referring to "11-18-1. X- and Y-feed motor home positions".
KE-430F, BE-438F
89
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-8. Upper shaft mechanism
Apply grease <GREASE BZL-300P> specified by Brother to the portions indicated by the white arrows.
* 17, 18 and 19 should be installed after carrying out the installations in “10-10. Lower shaft mechanism”.
* Set screws marked with * in the illustration are on the screw stop side.
* Refer to the next page for the points to note during reassembly.
1) Tighten the screw 5 of the thread take-up crank 4 so that it
is aligned with the hole in the upper shaft 1.
2) While pressing the thread take-up crank 4 so that there is
no play in it, tighten the two set screws 7.
Apply adhesive (Threebond 1401 or similar) to the thread
section of the screw 5.
C on next page
・A on next page
・Adjust while referring
to “11-14. Adjusting
the thread trimmer
cam position”.
B on next page
Apply adhesive (Threebond
1324 or similar) to the outer
circumference of the joint
assembly bearing 10.
・D on next page
・Be careful not to drop the
balancer 20.
E on next page
2860B
1. Upper shaft
11. Set screws [2 pcs: Tighten]
21. Balancer plate
2. Crank rod base
3. Pulley gear R
4. Thread take-up crank
5. Screw
6. Set screw [Tighten]
7. Set screws [2 pcs: Tighten]
8. Set screws [2 pcs: Tighten]
9. Set screws [2 pcs: Tighten]
10. Joint assembly
12. Thread trimmer cam
13. Motor assembly
14. Bolts [4 pcs]
15. Set screws [2 pcs: Tighten]
16. Set screws [2 pcs: Tighten]
17. Crank rod washer
18. Bolt
22. Bolts [2 pcs]
23. Rubber cap
24. Bobbin winder unite
25. Plain washers [2 pcs]
26. Screws [2 pcs]
(1) Eccentric wheel
(2) Rock gear shaft assembly
19. Set screws [2 pcs: Tighten]
20. Balancer
(Continued on next page.)
KE-430F, BE-438F
90
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
Tighten the set screw so that the screw stop a on the
motor shaft is in the same phase as the screw stop b on
the upper shaft 1.
Tighten the set screw so that the screw stop c on the
thread trimmer cam 12 is at a phase of approximately 180
degrees from the screw stop a on the motor shaft.
2859B
Reference line
2868B
2891B
With the motor assembly 13 provisionally installed, turn
it in the direction of the arrow and then tighten the four
bolts 14.
Install pulley gear R 3 so that it is aligned with the
reference line on the upper shaft 1.
Grease
Approx. 0.2 mm
Approx. 0.2 mm
2892B
2893B
1) Apply grease to the rock gear shaft assembly (2).
2) Tighten the two set screws 19 so that there are
gaps of 0.2 mm at both the front and rear of the
crank rod assembly 2.
With the edge of the balancer 20 pushed up against
the edge of the cam (1), tighten the two bolts 22. In
addition, check that there are gaps at section d (crank
rod assembly 2 and balancer 20).
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
91
10. ASSEMBLY
10-9. Needle bar mechanism
Apply grease <GREASE BZL-300P> specified by Brother to the portions indicated by the white arrows.
When tightening the two set screws
11, first turn the pulley approximately
Inside hole
10 times to the position where it turns
smoothly.
0.1mm
clearance
Horizontal
Screw stop
Align the set screw 11
with the screw stop.
3006B
Left-hand thread
Fit the beveled side of the
slide block into the groove
on the slide block guide 1.
After securing the needle bar, position
the slide block guide 1 so that the
machine pulley turns smoothly, and then
tighten the two bolts 2.
Align the set screw 9 with
the screw stop.
1. Slide block guide
2. Bolts [2 pcs: Temporarily tighten]
3. Washer
4. Thread take-up lever assembly
5. Washer
6. Needle bar crank
9. Set screws [3 pcs: Tighten]
10. Set screws [2 pcs: Tighten]
11. Set screws [2 pcs: Tighten]
12. Rubber caps [3 pcs]
13. Rubber cap
14. Needle bar connecting rod assembly
15. Screw [Tighten]
16. Slide block
7. Set screw collar
8. Thread take-up support shaft assembly
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
92
10. ASSEMBLY
17. Needle bar clamp
18. Needle bar [Insert from above]
19. Screw
With the needle bar 18 near
its highest position, apply
grease inside the holes.
20. Rubber cap
Inside
hole
2862B
Cut section
Align the needle bar 18 so that reference line A (the second lowest
reference line on the needle bar 18) or reference line a (top
reference line) is aligned with the lower edge of the needle bar bush
when the machine pulley is turned to lower the needle bar 18 to its
lowest position, and then set the cut section so that it is facing
forward and tighten the screw 19.
Needle bar
bush
4647Q
KE-430F, BE-438F
93
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-10. Lower shaft mechanism
Apply grease < GREASE BZL-300P > or < GREASE BZL-302R > specified by Brother to the portions indicated by the white
arrows.
1. Shuttle race base assembly
2. Oil tube support
3. Screw
4. Cord holder U3
5. Screw
6. Adjusting stud
7. Set Screw [Tighten]
GREASE BZL-302R
GREASE BZL-302R
2869B
(Continued on next page.)
KE-430F, BE-438F
94
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
* Set screws marked with * in the illustration are on the screw stop side.
While pushing the rock gear shaft assembly 9 and rock gear shaft
R 10 so that there is no play in the axial direction, tighten the two
set screws 11.
GREASE BZL-300P
Notch facing
straight down
2870B
Take up
the play
Take up
the play
Align the
angles of
the grooves
Gap distribution
2871B
8. Rock gear
9. Rock gear shaft assembly
10. Rock gear shaft R
11. Set screws [2 pcs: Tighten]
12. Set screws [2 pcs: Tighten]
(Continued on next page.)
KE-430F, BE-438F
95
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
Adjust while referring to “11-17. Adjusting
the backlash amount (play) of the lower
shaft gear”.
While pushing the bearing bush
assemblies 14 and 17 so that
there is no play in the axial
direction, tighten the four set
screws 18.
2872B
Gap distribution
Align
Align
13. Oil seal
14. Bearing bush assembly
15. Lower shaft assembly
16. Rubber seal L
17. Bearing bush assembly
18. Set screws [4 pcs: Tighten]
19. Driver
Take up
the play
Take up
the play
20. Bolt [Temporarily tighten]
21. Set screws [4 pcs]
22. Positioning plate
23. Screws [4 pcs]
1) The oil seal 13 and rubber seal L 16 cannot be reused, so have new parts
ready for use.
2) Make sure that the installation directions for the oil seal 13 and rubber seal
L 16 are correct.
3) Apply grease (BZL-500 grease) to the outer circumferences of the oil seal
13 and rubber seal L 16 when inserting the oil seal 13 and rubber seal L
16 into the holes in the bed.
(Temporarily tighten)
2873B
2874B
(Continued on next page.)
KE-430F, BE-438F
96
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
After applying sealant (Threebond 1215) to the
shaded area, install the gear cover 24 by tightening
the five screws 25 at a torque of 1 Nm.
24. Gear cover
25. Screws [5 pcs]
26. Grease support F
27. Screws [2 pcs]
28. Rubber caps [2 pcs]
(1) Rubber cap
2875B
2876B
Remove the rubber cap (1) and apply grease,
and then reinstall the rubber cap (1).
1) Turn the pulley to set the needle bar to
near its lowest position.
2) Insert the grease nozzle (3) into the
gear box as far as the lower shaft gear
(2), and apply 16g of grease (BZL-500
grease).
16g of grease
Insert as far as this
2877B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
97
10. ASSEMBLY
10-11. Lubrication
Adjust while referring to “11-6.
Rotary hook lubrication amount”.
1. Oil tank assembly
2. Oil tank nut
3. Oil tank plate
4. Plain washers [2 pcs]
5. Bolts [2 pcs]
6. Bolts [2 pcs]
2878B
10-12. Shuttle hook mechanism
2879B
2880B
1. Needle bar thread guide
2. Needle
3. Set screw
4. Shuttle hook
5. Shuttle race base
6. Shuttle race base setting claw [Close]
7. Bobbin case assembly
After installing the shuttle hook 4, carry out the adjustments in “11-3. Adjusting
the needle bar lift amount and the driver needle guard” and “11-4. Adjusting the
needle clearance”.
KE-430F, BE-438F
98
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-13. Thread trimmer mechanism (2)
Apply grease to the portions indicated by the white arrows.
<Seen from the right>
<Seen from below>
2881B
1) Apply grease to the pin (1) of the movable knife, and
then insert it into the hole in the movable knife
connecting plate (2), and then while inserting the pin
(3) of TN-connecting plate assembly F into the hole in
the thread nipper D assembly (4), install the needle
plate 14.
2) Check that the center of the needle hole and the tip of
the needle are aligned.
2883B
2882B
1. Fixed knife
9. Movable knife shoulder screw
2. Plain washers [2 pcs]
3. Spring washers [2 pcs]
4. Screws [2 pcs]
5. Movable knife spacer
6. Movable knife assembly
7. Movable knife collar
8. Thrust collar
* 10. Bobbin thread clamp spring [KE-430F only]
* 11. Plain washers [2 pcs] [KE-430F only]
* 12. Spring washers [2 pcs] [KE-430F only]
* 13. Screws [2 pcs] [KE-430F only]
14. Needle plate
15. Screws [2 pcs]
16. Flat screws [2 pcs]
For the BE-438F, parts marked with * are supplied as accessories. Install
them if necessary.
KE-430F, BE-438F
99
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-14. Work clamp arm mechanism (KE-430F)
Push the work clamp arm lever plate (3) in the direction
of the arrow to raise the work clamp (4) by about 5
mm, set so that there is a clearance of 0.1 mm
between the underside of the work clamp arm support
plate (5) and the slider (1), and then secure the slider
(1) of the work clamp support shaft (6) with the set
screw (2).
2885B
1. Feed plate
2. Screws [2 pcs]
3. Work clamp arm assembly
4. Plain washers [2 pcs]
5. Bolts [2 pcs]
(1) Slider
(2) Set screw
(3) Work clamp arm lever plate
(4) Work clamp
(5) Work clamp arm support plate
(6) Support shaft
(7) Needle hole
2884B
After installing, carry out test feeding and check that the needle hole (7) is not inside the work clamp (4) and the
frame of the feed plate 1. If the needle hole (7) is inside the frame, adjust the position of the work clamp arm
assembly 3 and the feed plate.
Apply grease to all sliding parts during assembly.
It is recommended that you
use commercially-available
SHIN
NISSEKI
Power
Knock WB2 as the grease
to be applied to the sliding
part of the work clamp.
Grease
2887B
a. Sliding portion of the work clamp
(Apply small amount of grease.)
b. Sliding portion of the work clamp arm lever shaft
and the work clamp arm levers R and L
c. Round portion of the work clamp arm lever plate
d. Slider of work clamp support shaft
2886B
KE-430F, BE-438F
100
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-15. Work clamp arm mechanism (BE-438F)
1. Feed plate
2. Screws [2 pcs]
3. Button clamp holder
4. Button clamp holder shaft
5. Set screws [2 pcs]
6. Nuts [2 pcs]
Adjusting screw
Compression spring
2888B
After installing, check that the needle passes into the button hole without touching the button. (Refer to “11-13.
Adjusting the position of the button clamp (BE-438F)”.)
Apply grease to the portions indicated by the arrows during assembly.
2889B
KE-430F, BE-438F
101
Download from Www.Somanuals.com. All Manuals Search And Download.
10. ASSEMBLY
10-16. Covers
2890B
1. Shuttle race cover assembly
2. Washer, wave spring [2 pcs]
3. Shoulder screws, 8-2 [2 pcs]
4. Face plate assembly
5. Screws [3 pcs]
8. Side cover
9. Screws [4 pcs]
10. Rear cover
11. Screws [4 pcs]
12. Top cover
6. Eye guard assembly
7. Bolts [2 pcs]
13. Screws [4 pcs]
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
102
11. ADJUSTMENT
11. ADJUSTMENT
CAUTION
Maintenance and inspection of the sewing machine
Hold the machine head with both hands when tilting
should only be carried out by a qualified technician.
it back or returning it to its original position.
Furthermore, after tilting back the machine head, do
not push the face plate side or the pulley side from
above, as this may cause the machine head to
topple over, which may result in personal injury or
damage to the machine.
Ask your Brother dealer or a qualified electrician to
carry out any maintenance and inspection of the
electrical system.
Turn off the power switch and disconnect the power
cord from the wall outlet at the following times,
otherwise the machine may operate if the foot
switch is depressed by mistake, which may result in
injury.
If the power switch needs to be left on when carrying
out some adjustment, be extremely careful to
observe all safety precautions.
If any safety devices have been removed, be
absolutely sure to re-install them to their original
positions and check that they operate correctly
before using the machine.
・When carrying out inspection, adjustment and
maintenance
・When replacing consumable parts such as the
rotary hook
11-1. Standard thread tension
KE-430F
Use
BE-438F
Medium-weight
materials (-03)
#50 or
equivalent
#50 or
Knitted wear
(-0K)
Foundation
garments (-0F)
#60 or
Heavy-weight
materials (-05)
#60 or
equivalent
#80 or
equivalent
0.8 - 1.2
[80 - 120]*1
Upper thread
Lower thread
#30 or equivalent #60 or equivalent
#50 or equivalent #60 or equivalent
equivalent
#60 or
equivalent
equivalent
Upper thread tension (N)
[Tension value]
1.2 – 1.8
0.5 - 1.2
[70 - 130]*1
[50 - 150]*1
Lower thread tension (N)
Pre-tension (N)
Needle
0.2 - 0.3
0.05 - 0.3
DP x 5KN #11
0.2 - 0.3
0.1 - 0.4
DP x 5 #14
DP x 5 #9
DP x 17NY #19
DP x 17NY #12
*1: This is the tension value when the pretension is 0.05 N.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
103
11. ADJUSTMENT
11-1-1. Upper and lower thread tension
2318B
2319B
<Foot switch>
Backward depression position
Neutral
<2-pedal foot switch(option)>
Work clamp switch (2-step)
Start switch
2923B
2924B 2925B
<Operating the upper thread tension>
● When using a foot switch
In the sewing standby condition and during test operation standby, the thread tension in the TENSION display (2) which has
been set for the section appearing in the SECTION No. display (1) on the operation panel will be output while the foot switch
is being depressed backward.
When the foot switch is returned to the neutral position, the thread tension will be released.
* If the work clamp/button clamp is lowered when the foot switch is returned to the neutral position, the thread tension output
will be maintained.
● When using a 2-pedal foot switch (option)
In the sewing standby condition and during test operation standby, the thread tension which has been set in the SECTION No.
1 (sewing start section) will be output while the work clamp/button clamp is lowered (while the work clamp switch is being
depressed) regardless of the section which appears in the SECTION No. display (1) on the operation panel.
When the work clamp switch is released, the thread tension will be released.
* If the work clamp/button clamp is lowered when the work clamp switch is released, the thread tension output will be
maintained.
* The above operations are enabled when memory switch No. 072 is set to “1” or “2”.
KE-430F, BE-438F
104
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-1-2. Thread take-up spring
KE-430F
Foundation
garments (-0F)
6 - 11
Use
BE-438F
Medium-weight
Knitted wear
(-0K)
Heavy-weight
materials (-05)
materials (-03)
Thread take-up spring
height (mm)
6 - 11
Thread take-up spring
tension (N)
0.2 - 0.4
0.6 - 1.0
0.15 – 0.35
<Thread take-up spring height>
Lower
Higher
Loosen the set screw (1) and turn the tensioner body to
adjust the thread take-up spring height.
2320B
<Thread take-up spring tension>
Stronger
Weaker
2321B
Adjust by turning the shaft (2) with a screwdriver.
NOTE:
When the spring height (stroke) is great or the spring tension is insufficient, it may cause the thread end length to vary after
thread trimming.
KE-430F, BE-438F
105
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-1-3. Arm thread guide C
The standard position of arm thread guide C (1) is when the
screw (2) is aligned with the position of the reference line.
To adjust the position, loosen the screw (2) and then move
arm thread guide C (1).
・ When sewing heavy-weight materials, move arm thread
guide C (1) to the left. (The thread take-up amount will
increase.)
Increase
Decrease
・ When sewing light-weight materials, move arm thread
guide C (1) to the right. (The thread take-up amount will
decrease.)
Reference
line
2322B
11-1-4. Needle bar bush thread guide D
Check that needle bar bush thread guide D (1) is at the
middle of the needle bar (2).
NOTE:
If needle bar bush thread guide D (1) is not in the correct
position, the thread may pull out or skipped stitches may
occur.
2325B
11-2. Adjusting the needle bar height
2326B
2904B
1. Loosen the two bolts (1), and then remove the eye guard assembly (2).
2. Turn the pulley in the direction of the arrow to move the needle bar to the lowest position. Then remove the rubber cap (4),
loosen the screw (5) and then move the needle bar up or down to adjust so that the second reference line from the bottom
of the needle bar (reference line A) is aligned with the lower edge of the needle bar bush (3).
* If using a DP x 5 needle, use the highest reference line (reference line a).
KE-430F, BE-438F
106
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-3. Adjusting the needle bar lift amount and the driver needle guard
2926B
2544Q
Center of the needle
Tip
2927B
0135Q
1. Turn the pulley in the direction of the arrow to raise the needle bar from the lowest position until the lowest reference line
on the needle bar (reference line B) is aligned with the lower edge of the needle bar bush (1).
* If using a DP x 5 needle, align with reference line b which is the second reference line from the top.
NOTE:
Check that the wiper and the needle do not touch when lowering the needle bar. If the wiper is in a position where it will
touch the needle, move the wiper to the right by hand so that it does not touch the needle.
2. Loosen the bolt (2).
3. Move the driver (3) back and forth to adjust so that it is touching the needle when the tip of the rotary hook is aligned with
the center of the needle, and then tighten the bolt (2).
NOTE:
If the needle contact pressure from the driver (3) is too great, skipped stitches may occur. On the other hand, if the
driver (3) is not touching the needle, the tip of the inner rotary hook will obstruct the needle, resulting in an excessively
high amount of friction.
11-4. Adjusting the needle clearance
0.01 - 0.08mm
0138Q
2328B
Turn the pulley in the direction of the arrow to align the tip of the rotary hook with the needle center line. Then loosen the set
screw (1) and turn the rotary hook adjustment shaft (2) to adjust so that the clearance between the tip of the needle and the
rotary hook is 0.01 to 0.08 mm.
KE-430F, BE-438F
107
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-5. Adjusting the shuttle race thread guide
2329B
Install the shuttle race thread guide (1) by pushing it in the direction of the arrow so that the needle groove is aligned with the
center of the needle plate hole.
NOTE:
If the shuttle race thread guide is in the wrong position, thread breakages, soiled thread or thread entanglements may
occur.
The position of the shuttle race thread guide is adjusted at the time of shipment from the factory. It should not be changed if
at all possible.
11-6. Rotary hook lubrication amount
KE-430F (-05 specifications)
KE-430F (-03, -0K, -0F specifications), BE-438F
More
oil
More
oil
Less
oil
Less
oil
2729B
1. Tilt back the machine head.
2. Loosen the two bolts (1), and then adjust by moving the oil tank assembly (2) up or down.
KE-430F (-05 specifications)
The standard position is when the centers of the two bolts (1) are aligned with the reference line on the oil tank plate (3).
KE-430F (-03, -0K, -0F specifications), BE-438F
The standard position is when the oil tank assembly (2) is as far forward as possible as shown in the illustration.
<If you would like to increase the lubrication amount
further>
Remove the two rubber caps 5.5 (4).
* Keep the two rubber caps 5.5 (4) safely so that they do
get lost.
2905B
KE-430F, BE-438F
108
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-7. Adjusting the thread trimming
Push
down
A
2730B
1. Remove the top cover, side cover and rear cover.
2. Turn the pulley in the direction of the arrow to move the needle bar to its lowest position.
3. Loosen the three bolts (1), and then set the clearance (section A) between the rubber and the plunger to 0.65 mm. While
holding them in this position, move the thread trimmer solenoid assembly (2) back and forth.
4. Set the thread trimmer collar (3) so that it is touching against the outside of the thread trimmer cam (4), and then while
pushing the thread trimmer solenoid assembly (2) down, tighten the three bolts (1).
5. Install the top cover, side cover and rear cover.
B
A
2957B
* Set so that the clearance (section A) is 0 mm, and then check that there is a clearance of 0.1 to 0.3 mm between the thread
trimmer collar (3) and the outside of the thread trimmer cam (4) (section B).
KE-430F, BE-438F
109
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-8. Adjusting the position of the movable knife
2732B
<Thread trimmer cam seen from the side>
Reverse position
2733B
1. Remove the top cover and the side cover.
2. Turn the pulley by hand in the direction of the arrow to move the needle bar to its lowest position, and then turn the cam
shaft (1) so that the thread trimmer collar (2) goes into the groove in the thread trimmer cam (3).
3. Tilt back the machine head.
4. With the thread trimmer collar (2) inserted into the groove of the thread trimmer cam (3), turn the pulley by hand in the
direction of the arrow to set the thread trimmer driving lever (4) to the reverse position (when the thread take-up (5) is close
to its lowest position).
Touching
2734B
2958B
5. Loosen the bolt (6).
6. Move thread trimmer rod H assembly(7) back and forth to adjust so that the ridge line on the movable knife (8) is touching
the edge of the index mark (9), and then while keeping the parts in this position, tighten the bolt (6).
7. Turn the pulley so that the thread trimmer driving lever (4) is in the reverse position, and then while pushing thread trimmer
rod V assembly (10) in the direction of the arrow so that the thread trimmer collar (2) is touching the inside of the thread
trimmer cam (3), check if the ridge line on the movable knife (8) is touching the edge of the index mark (9).
8. Return the machine head to its original position, and then install the top cover and the side cover.
KE-430F, BE-438F
110
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-9. Replacing the movable knife and fixed knife
2331B
1. Open the shuttle race cover, remove the two screws (1), and then remove the feed plate (2).
2. Remove the two screws (3) and the two flat screws (4), and then remove the needle plate (5).
3. Remove the movable knife (6) and the fixed knife (7).
2332B
2333B
4. Install new fixed knife (7) in the position shown in the illustration.
5. Apply grease to the outside of the movable knife collar (8) and to the movable knife shoulder screw (9), and then install the
new movable knife (6) together with the thrust washer (10) and movable knife spacer (11).
6. Check that the movable knife (6) and the fixed knife (7) cut the thread cleanly.
7. Apply grease to the pin (12) of the movable knife, and then insert it into the hole in the movable knife connecting plate (13),
and then while inserting the pin (15) of TN-connecting plate assembly F into the hole in the thread nipper D assembly (14),
install the needle plate (5).
8. Check that the center of the needle hole and the tip of the needle are aligned.
Select an accessory movable knife spacer (11) which allows
the movable knife (6) to cross over the fixed knife (7) with a
force that is as gentle as possible while still allowing the
thread to be trimmed.
* Move the movable knife (6) as shown in the illustration and
check that it trims the thread cleanly.
NOTE:
If the movable knife spacer (11) is too thick, it will not be
possible to trim the thread.
2334B
KE-430F, BE-438F
111
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-10. Adjusting the work clamp lift amount (KE-430F)
Adjust so that the actual maximum lift amount for the work clamp is 17 mm above the top of the needle plate when the
maximum work clamp height has been set to 17 mm using the operation panel (refer to “Work clamp lifting height” on P.17).
2385B
1. Loosen the bolt (1) and move the work clamp arm lever plate (2) up or down to adjust.
2. Apply grease to the bottom of the work clamp lifter plate assembly (3), to the top of the work clamp arm lever plate (2) and
to the sliding part of the work clamp (4) (grease is already applied at the time of shipment), and check that the movement
becomes easier.
11-11. Adjusting the button clamp lift amount (BE-438F)
Adjust so that the actual maximum lift amount for the button clamp is 13 mm above the top of the needle plate when the
maximum work clamp height has been set to 13 mm using the operation panel (refer to “Work clamp lifting height” on P.17).
2386B
Remove the compression spring (1), loosen the screw (2) and adjust the button clamp holder hook assembly (3) by moving it
up and down.
* If the button clamp lift amount is too large, the button clamp will not be raised.
KE-430F, BE-438F
112
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-12. Adjusting the holding pressure (BE-438F)
Loosen the nut (1) and turn the nut (2) to the point where it is
just tight enough that the material will not slip out of place
when it is slightly pulled (keeping pressure as slight as
possible).
2387B
11-13. Adjusting the position of the button clamp (BE-438F)
1. Loosen the two bolts (1) and adjust the button clamp
base (2) by moving it.
2. Carry out test feeding to check that the needle will go
through the button hole with no contact.
2388B
11-14. Adjusting the thread trimmer cam position
1. Remove the top cover.
2. Loosen the two set screws (1), and then adjust the
position of the thread trimmer cam (3) so that the distance
between the edge of the collar shaft (2) and the edge of
the thread trimmer cam (3) is 0.5 - 0.7 mm. After adjusting,
tighten the two set screws (1).
2736B
KE-430F, BE-438F
113
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-15. Adjusting the thread wiper
<Thread wiper height adjustment>
Loosen the two screws (2) and adjust
the thread wiper (1) so that the
clearance between the top of the thread
wiper (1) and the tip of the needle is
approximately 2 mm when the thread
wiper (1) is aligned with the center of
the needle at the needle bar stop
position.
NOTE:
Check that the needle bar thread guide
(3) and the thread wiper base shaft (4)
are not touching at this time.
Approx. 2 mm
2338B
2906B
<Thread wiper racking width adjustment>
1. Remove the side cover.
2. Loosen the set screw (1) and
adjust so that the distance from the
thread wiper to the center of the
needle is as shown in the
illustration.
Approx. 25 mm Approx. 20 mm
2336B
4683Q
KE-430F, BE-438F
114
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-16. Adjusting the tension release amount
2737B
A
B
2738B
2928B
2739B
1. Remove the two screws (1), and then remove the solenoid cover (2).
2. Remove the two screws (3).
3. With the plunger (5) of the tension solenoid (4) pushed all the way in, loosen the nut (8) and turn the bolt (6) to adjust so
that the end of the bolt (6) is 11.5 m from the side of the solenoid setting plate (7). (Figure A)
4. With the tension solenoid (4) installed to the arm with the two screws (3), insert spacers or similar to operate the thread
tension so that distance (a) is 1.9±0.1 mm. (Figure B)
* Select a spacer that can maintain the distance (a) without becoming bent when the tension solenoid (4) operates.
* Refer to “11-1-1. Upper and lower thread tension” for details on operating the thread tension.
5. Loosen the bolt (9) and adjust the sideways position of the set collar (10) so that the opening amount (b) for the tension
discs is 0 mm. After adjusting, retighten the bolt (9).
* Make sure that the movement range for the set collar (10) does not pass the edge of the shaft (11) at this time.
6. Release the thread tension.
Check that the opening about (b) for the tension discs is 0.8 to 1.5 mm.
7. Install the solenoid cover (2) with the two screws (1).
KE-430F, BE-438F
115
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-17. Adjusting the backlash amount (play) of the lower shaft gear
1. Tilt back the machine head.
2. Open the shuttle race base cover.
3. Remove the shuttle race base, shuttle hook and bobbin
case.
4. Remove the two screws (with washer) (1), and then
remove grease holder F (2).
2998B
Backlash amount
becomes smaller
Backlash amount
becomes greater
2959B
5. Remove the two rubber caps (3).
6. Loosen the two set screws (4) and the two set screws (5).
7. Use the tip of a screwdriver or similar to adjust the front and back rock gear collars (6) so that the backlash amount (play)
is 0.05 to 0.2 mm.
*
Alternately move the phase of the front and back rock gear collars (6) slightly to adjust so that the phase of the front
and back rock gear collars (6) is about the same (within ±10 degrees).
・ If the backlash amount (play) is small, it will result in wear in the rock gear (7) and the lower shaft gear (8).
・ If the backlash amount (play) is large, it will result in wear in the rock gear (7) and the lower shaft gear (8) and also
result in increased noise during sewing.
8. First tighten the two set screws (4), and then tighten the two set screws (5).
9. Recheck that the backlash amount (play) which was adjusted in step 7 above is correct.
10. Install any parts which were removed from step 5 onward by carrying out the removal procedure in reverse.
KE-430F, BE-438F
116
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-18. Adjusting the home position
11-18-1. X- and Y-feed motor home positions
With the power switch turned off, turn the pulley in the direction of the arrow to set the needle to the needle up stop
position (near the highest thread take-up position).
1
2
While pressing the
the power switch.
keys simultaneously, turn on
・ "orG" will flash in the PROGRAM No. display and the
currently-recorded offset value will be displayed in the
menu display.
2788B 2789B
Press the SELECT key so that either the X-SCALE
indicator or the Y-SCALE indicator illuminates.
3
4
2790B 2401B
Depress the foot switch to the 2nd step (for a 2-pedal foot switch,
depress the start switch). (*1)
・ Home position detection for the X-feed or Y-feed motor will be
2nd step
carried out based on the currently-displayed offset value.
・ "orG" will illuminate in the PROGRAM No. display.
*
If you press the RESET key for 2 seconds or more at this time, the
offset value will be reset to "0" and home position detection for the
X-feed or Y-feed motor will be carried out.
4441Q 2791B 2634B
(*1) When “UP” appears in the menu display and the CAUTION indicator flashes and the buzzer sounds, turn the pulley in
the direction of the arrow to move the needle bar to the up stop position (near the highest thread take-up position).
(Continued on next page.)
KE-430F, BE-438F
117
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
Use the home position standard plate and press the
keys to change the offset value (-50 to 50) so that the
needle drops at the home position.
or
5
・ The X-feed or Y-feed motor will operate according to
the offset value.
・ The offset value in the menu display will flash, and
“JoG” will illuminate in the TENSION display.
For example, if the offset value is 5
2792B 2793B 2794B 2795B
Depress the foot switch to the 2nd step (for a 2-pedal foot
switch, depress the start switch) to provisionally confirm
the offset value. (*1)
・ Feed motor home position detection will be carried out
based on the currently-displayed offset value. Check
the home position.
6
2nd step
・ “JoG” will disappear from the TENSION display.
4441Q 2796B
Repeat steps 5 and 6 to set the home position to the correct position.
Press the ENTER key to confirm the offset value.
7
8
・The offset value will illuminate in the menu display.
* If the offset value has not been provisionally confirmed
(if “JoG” is illuminated), the invalid buzzer will sound.
2414B
End adjustment mode.
Press the TEST key.
9
・ The display will return to the normal display and the
sewing machine will switch to home position detection
standby.
2404B
TEST indicator switches off
(*1) When “UP” appears in the menu display and the CAUTION indicator flashes and the buzzer sounds, turn the pulley in
the direction of the arrow to move the needle bar to the up stop position (near the highest thread take-up position).
KE-430F, BE-438F
118
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-18-2. Work clamp lift motor home position
With the power switch turned off, turn the pulley in the direction of the arrow to set the needle to the needle up stop
position (near the highest thread take-up position).
1
2
While pressing the
the power switch.
keys simultaneously, turn on
・ "orG" will flash in the PROGRAM No. display and the
currently-recorded offset value will be displayed in the
menu display.
2797B 2789B
Press the SELECT key until the THREAD/CLAMP indicator
illuminates.
3
4
2798B 2401B
Depress the foot switch to the 2nd step (for a 2-pedal foot switch,
depress the start switch).
・ Home position detection for the work clamp lift motor will be carried
out based on the currently-displayed offset value.
・ "orG" will illuminate in the PROGRAM No. display.
2nd step
*
If you press the RESET key for 2 seconds or more at this time, the
offset value will be reset to "0" and home position detection for the
work clamp lift motor will be carried out.
4441Q 2634B
1. Remove the top cover. Press the
key until the
5
TR-driving lever (1) is at the position where it starts
moving backward to set the offset value (-80 to 20).
(The TR-driving lever (1) will operate according to the
offset value.)
The offset value in the menu display will flash, and
“JoG” will illuminate in the TENSION display.
2. Press the
key once to reduce the offset value by 1.
For example, if the offset value is -2
3007B 2800B 2801B 2899B
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
119
11. ADJUSTMENT
Depress the foot switch to the 2nd step (for a 2-pedal foot switch,
depress the start switch) to provisionally confirm the offset value.
6
・ Work clamp lift motor home position detection will be carried out
based on the currently-displayed offset value. Check the home
position.
2nd step
・ “JoG” will disappear from the TENSION display.
4441B
Repeat steps 5 and 6 to set the home position to the correct position.
7
8
Press the ENTER key to confirm the offset value.
・The offset value will illuminate in the menu display.
* If the offset value has not been provisionally confirmed
(if “JoG” is illuminated), the invalid buzzer will sound.
2414B
End adjustment mode.
Press the TEST key.
9
・The display will return to the normal display and the
sewing machine will switch to home position detection
standby.
2404B
TEST indicator switches off
Turn off the power switch and install the top cover.
10
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
120
11. ADJUSTMENT
11-18-3. Thread nipper motor home position
With the power switch turned off, turn the pulley in the direction of the arrow to set the needle to the needle up stop
position (near the highest thread take-up position).
1
Open the shuttle race base cover and remove the shuttle race base, shuttle hook and bobbin case assembly.
2
3
While pressing the
the power switch.
keys simultaneously, turn on
・ "orG" will flash in the PROGRAM No. display and
the currently-recorded offset value will be displayed
in the menu display.
2802B 2789B
Press the SELECT key until the TENSION indicator
illuminates.
4
5
2803B 2401B
Depress the foot switch to the 2nd step.
・ Home position detection for the thread nipper motor will be carried out
based on the currently-displayed offset value.
・ "orG" will illuminate in the PROGRAM No. display.
2nd step
*
If you press the RESET key for 2 seconds or more at this time, the
offset value will be reset to "0" and home position detection for the
thread nipper motor will be carried out.
4441Q 2634B
Press the
or
key to change the offset value (-50 to 50) so that
6
the hole (2) in the needle hole plate is near the center of the hole in
the thread nipper D assembly (1).
For example, if the offset value is 8
・ The thread nipper will operate in accordance with the offset
value.
・ The offset value in the menu display will flash, and “JoG” will
illuminate in the TENSION display.
2804B 2805B
(Continued on next page.)
KE-430F, BE-438F
121
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
Depress the foot switch to the 2nd step to provisionally confirm the
offset value.
7
・ Thread nipper motor home position detection will be carried out
based on the currently-displayed offset value. Check the home
position.
2nd step
・ “JoG” will disappear from the TENSION display.
4441Q 2806B
Press the F1, F2 and F3 keys and check the respective positions.
・ When the F1 key is pressed, the thread nipper D assembly (1)
will move to the home position.
8
* “F1” will illuminate in the SECTION No. display.
・ When the F2 key is pressed, the thread nipper D assembly (1)
will move to the thread nipping position.
* “F2” will illuminate in the SECTION No. display.
Check that the thread is being firmly held at this time. If the
thread is not being held, adjust the home position (F1) so that the
hole in the thread nipper D assembly (1) is not inside the hole (2)
in the needle hole plate.
・ When the F3 key is pressed, the thread nipper D assembly (1)
will move to the thread release position.
* “F3” will illuminate in the SECTION No. display.
2807B 2808B 2809B
Depress the foot switch to the 2nd step to return the thread nipper
motor to the home position.
9
・ The SECTION No. display will stop illuminating.
2nd step
4441Q 2810B
Repeat steps 6 to 9 to set the home position.
10
11
Press the ENTER key to confirm the offset value.
・The offset value will illuminate in the menu display.
* If the offset value has not been provisionally
confirmed (if “JoG” is illuminated), the invalid buzzer
will sound.
2414B
End adjustment mode.
Press the TEST key.
12
13
・The display will return to the normal display and the
sewing machine will switch to home position
detection standby.
TEST indicator switches off
2404B
Turn off the power switch, install the shuttle race base, shuttle hook and bobbin case assembly, and then close the
shuttle race base cover.
KE-430F, BE-438F
122
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-19. Adjusting the main shaft motor standard position
Remove the needle, the needle bar thread guide and the feed plate.
1
While pressing the [+ -] keys simultaneously, turn on the
power switch.
2
・ "Mot" will illuminate in the PROGRAM No. display and
"Set" will illuminate in the menu display.
2811B 2818B
Turn the pulley one full turn in the direction of the arrow.
・ " UP" will flash in the SECTION No. display and
3
"
dn" will flash in the TENSION display.
*
If nothing is displayed, turn the pulley by hand until
the displays appear.
2813B
Turn the pulley in the direction of the arrow to lower the
needle bar from its highest position to the height shown in
the illustration at left.
4
2814B
Press the ENTER key.
5
・ " UP" will illuminate in the SECTION No. display and
"
dn" will illuminate in the TENSION display.
*
If the displays are still flashing, carry out step 4 once
more.
2414B 2815B
(Continued on next page.)
KE-430F, BE-438F
123
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
End adjustment mode.
Press the TEST key.
6
・ The display will return to the normal display and the
sewing machine will switch to home position detection
standby.
2404B
TEST indicator switches off
Turn off the power switch and install the needle, the needle bar thread guide and the feed plate.
7
KE-430F, BE-438F
124
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
11-20. Correcting the digital tension output
・ The procedure for correcting the tension (output) from the
digital tension involves carrying out the procedure of measuring
the actual upper thread tension and entering the measured
value using the operation panel four times.
No. of
measurement
Standard tension value
for digital tension (gf)
1st
2nd
3rd
20
80
・ The standard values for the four tensions for the digital tension
vary for each measurement as shown in the table at right.
By entering the actual measurement values each time, the
digital tension output will be automatically corrected, and the
tension that corresponds to the setting can then be obtained
when sewing.
180
4th
330
1. Adjust the pretension to 5 to 7 gf (0.05 to 0.07 N).
* At this time, use the TOYOBO polyester #50 (white) thread
which is recommended by Brother.
1
2. Thread the upper thread as shown in the illustration at left.
NOTE:
Do not thread the thread through the thread take-up spring.
* If you do not observe the above note, the digital tension output
correction may not be carried out correctly.
2816B 2817B
2
While pressing the
switch.
keys simultaneously, turn on the power
* Keep pressing the
key until the model name is displayed
and the buzzer beeps once.
The tension discs will close, and “tEn” will illuminate in the
PROGRAM No. display, “ 1” will illuminate in the SECTION No.
display, and a value from “0” to “39” will illuminate in the menu display
respectively.
* The value in the menu display may vary for individual sewing
machines.
2819B 2818B
(Continued on next page.)
KE-430F, BE-438F
125
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ADJUSTMENT
Use a tension gauge to measure the upper thread tension as shown
in the illustration at left.
3
Press the
or
key to increase or decrease the value appearing
in the menu display until it corresponds with the measurement value.
For example, if the upper thread
tension is 28 gf
*
*
Round off any decimal places in the measurement value.
The units for the measurement values which are input to the
operation panel are “gf”. If the values are measured using units of
“N”, convert using a factor of 1 N ≒ 100 gf.
*
The value will illuminate in the menu display, and it will change to
flashing if it is increased or decreased.
2820B 2821B
1. Press the ENTER key.
2. Open the tension discs and then close them again.
4
・ "tEn" will illuminate in the PROGRAM No. display, the number of
the measurement will illuminate in the SECTION No. display, and
the allowable setting range will illuminate in the menu display.
(Refer to the table below.)
* The value in the menu display may vary for individual sewing
machines.
NOTE:
If you need to enter a value which is greater than the allowable setting
range in the table, problems may occur with the digital tension.
Refer to “11-16. Adjusting the tension release amount” and then
repeat the procedure from step 1.
2414B
Repeat steps 3 and 4 to set the 2nd to 4th measurements of the upper thread tension.
5
6
When the ENTER key is pressed after the 4th measurement, “END”
will appear in the menu display and the tension discs will open.
2822B
Turn off the power switch.
7
Standard
value (gf)
Allowable setting
range (gf)
SECTION No. display
Setting value
1st
2nd
3rd
4th
20
[0～39]
80
[40～119]
[120～239]
[240～419]
180
330
Number of measurement
2819B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
126
11. ADJUSTMENT
11-21. Checking the machine head switch
1. Turn on the power switch.
2. Check that no error numbers appear on the operation
panel.
<If error [E050], [E051] or [E055] is displayed>
If the machine head switch (1) is not turned on, error [E050],
[E051] or [E055] will occur.
Use the screw (2) to adjust the installation position of the
machine head switch as shown in the illustration.
2295B
11-22. Setting method for standard depression strokes (Foot switch)
Use the following procedure to set the operating positions for the depression stroke.
Signal setting entry
While pressing the
switch.
and
key, turn on the power
1
・ "PdL" will illuminate in the PROGRAM No. display
and “1.Frt” will illuminate will illuminate in the menu
display.
2826B
Memorizing the maximum forward position
With the foot switch depressed all the way forward, wait
until the value in the TENSION display stabilizes and
then press the ENTER key.
2
* XXX indicates the treadle depression voltage.
2827B
Memorizing the neutral position
With your foot released from the foot switch, wait until the
value in the TENSION display stabilizes and then press
the ENTER key.
3
4
2828B
Memorizing the maximum backward position
With the foot switch depressed all the way backward,
wait until the value in the TENSION display stabilizes and
then press the ENTER key.
2829B
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
127
11. ADJUSTMENT
Completion of setting
“ END” will be displayed in the menu display.
5
NOTE:
If the foot switch operations are not carried out correctly,
“ END” will not be displayed and the buzzer will sound.
After “1.Frt” is displayed in the menu display, repeat the
operation from step 2.
2830B
Turn off the power switch.
6
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
128
12. APPLYING GREASE
12. APPLYING GREASE
CAUTION
Be sure to wear protective goggles and gloves when handling the lubricating oil and grease, so that they do not get
into your eyes or onto your skin, otherwise inflammation can result.
Furthermore, do not drink the oil or eat the grease under any circumstances, as they can cause vomiting and
diarrhoea.
12-1. Applying grease (Work clamp: KE-430F)
Periodically apply grease to the sliding parts of the work
clamp (1) and the work clamp arm (2).
NOTE:
Viewed from directly above
After replacing the work clamp (1), be sure to apply
grease before using it.
Grease
* It is recommended that you use commercially-available
NIPPON OIL CORPORATION Powernoc WB 2 grease for
the work clamp (1).
2312B
12-2. Applying grease (When “GREASEUP” appears)
If “GrE” and “AS.UP" flash on the PROGRAM No. display (1) and the menu display (2) respectively, and a buzzer sounds
when the power switch is turned on, it means that grease needs to be applied. (The sewing machine will not operate at this
time, even if the foot switch is depressed.)
Apply grease as required, while referring to the following for details.
2907B
<To continue sewing temporarily without applying grease>
1. Press the RESET key (3).
2. The PROGRAM No. display (1) and the menu display (2) will change to the normal displays, and sewing can be carried
out by depressing the foot switch.
KE-430F, BE-438F
129
Download from Www.Somanuals.com. All Manuals Search And Download.
12. APPLYING GREASE
NOTE:
• "GrE" and "AS.UP" will continue to be displayed each time the power is turned on until grease is applied and the notification
is reset by carrying out the procedure on page 131.
• If you continue to use the sewing machine after the “GrE” and “AS.UP" notification appears without applying grease (or
without carrying out the reset procedure), “E100” will appear after a certain period of time and the sewing machine will be
forcibly prevented from operating for safety reasons.
If this happens, apply grease and carry out the reset procedure.
* If you continue to use the sewing machine after carrying out the reset procedure but without applying grease,
problems with the sewing machine may result.
<Applying grease>
Use Brother-specified “Grease unit (SB1275-001)”.
1. Removing the grease assembly
1. Remove the four screws (1), and
then remove the rear cover (2).
2. Remove the grease assembly (3)
from inside the rear cover (2).
2458B
2. Using the tube
2313B
Use in “B. Applying grease to the rock gear shaft
F assembly”.
KE-430F, BE-438F
130
Download from Www.Somanuals.com. All Manuals Search And Download.
12. APPLYING GREASE
3. Applying grease
< A. Applying grease to the eccentric wheel >
2314B
1. Turn off the power switch.
2. Remove the four screws (1), and then remove the top cover (2).
3. Remove the bolt (4) from the eccentric wheel (3).
* Be careful not to drop the bolt (4) when removing it.
4. Loosen the two bolts (5), and slide the grease cover (6) in the direction of the arrow.
* To prevent the bolts (5) from being dropped, do not remove them completely.
5. Wipe away any grease which is remaining inside the
eccentric wheel (3).
6. Insert the grease nozzle into the holes in the eccentric
wheel (3), and apply the grease.
* Insert the grease nozzle into both holes to apply the
grease, in order to make sure that the grease is applied
evenly without missing any parts.
7. Check that enough grease has been applied so that it is
overflowing slightly from the edges.
8. Return the grease cover (6) to its original position, and
then secure it by tightening the bolt (4) and the two bolts
(5).
Grease
NOTE:
Securely tighten the bolt (4) and the two bolts (5). If any of
these bolts are loose, grease may leak out and problems
with sewing machine operation such as seizing may occur.
2316B
KE-430F, BE-438F
131
Download from Www.Somanuals.com. All Manuals Search And Download.
12. APPLYING GREASE
< B. Applying grease to the rock gear shaft F assembly >
1. Tilt back the machine head.
2. Loosen the two screws (1), and then remove grease
holder F (2).
3. Turn the pulley in the direction of the arrow to move the
rock gear shaft F assembly (3) to the most forward
position.
4. Remove the bolt (4) and the crank rod washer (5).
5. Insert the grease nozzle (6) into the hole in the rock gear
shaft F assembly (3) as far as it will go as shown in the
illustration, and apply grease until it is overflowing slightly
from the edges.
6. Pull out the grease nozzle (6) while adding the grease.
7. Install the bolt (4) and the crank rod washer (5).
8. Install grease holder F (2) with the two screws (1).
9. Install the rear cover with the four screws.
2317B
NOTE:
• Once the grease tube has been opened, remove the nozzle from the tube, attach the cap securely and store the tube in a
cool dark place.
• The grease should be used as quickly as possible.
• When using the grease again, remove any old grease from inside the nozzle first.
(Store the tube away carefully once the tube has been opened, otherwise the grease remaining inside the tube may
deteriorate, and this may affect its lubricating performance.)
<Resetting the grease up counter>
Once the grease has been applied, follow the procedure
below to reset the cumulative number of stitches between
grease applications.
1. While pressing the F1 key (1), turn on the power switch.
“GCt” will appear in the PROGRAM No. display (2), and
the cumulative number of stitches until grease should be
applied will be displayed in the total of six columns in the
section No. display (3) and the menu display (4) in units of
10,000 stitches.
2. Press and hold the RESET key (5) for 2 seconds or more.
(This completes the reset procedure.)
3. When you press the TEST key (6), the displays will return
to their normal displays.
2344B
KE-430F, BE-438F
132
Download from Www.Somanuals.com. All Manuals Search And Download.
13. HOW TO INSTALL THE FEED PLATE FOR KE-430C SERIES IN KE-430F AND BE-438F
13. HOW TO INSTALL THE FEED PLATE FOR
KE-430C SERIES IN KE-430F AND BE-438F
If using the feed plate for the KE-430C and BE-438C, install it as follows.
<KE-430F>
4868Q
For KE-430F
For KE-430C
4870Q
Countersink
Do not use the screws for feed
plate that is used for the KE-430C.
4869Q
Install using the two screws (1) and the accessory feed plate cover (2), screw (3) and washer (4) as shown in the illustration.
<BE-438F>
For BE-438F
For BE-438C
4871Q
Install using the two screws (1) and the accessory feed plate cover (2) and screw (3) as shown in the illustration.
KE-430F, BE-438F
133
Download from Www.Somanuals.com. All Manuals Search And Download.
14. INSTALLING THE 2-PEDAL FOOT SWITCH (OPTION)
14. INSTALLING THE 2-PEDAL FOOT SWITCH (OPTION)
The foot switch conversion harness (SB1565001) that is sold separately is required.
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
before opening the face plate of the control box. Touching areas where high voltages are present will result in
serious injury from electric shocks.
Be sure to connect the ground.
If the ground connection is not secure, you run a high risk of serious injury from electric shocks, and problems with
correct operation will also occur.
No. 2-pedal foot switch
10P connector
1
2
3
4
5
6
7
8
9
10
-
-
-
-
Start
0V
0V
Clamp
Option
0V
2825B
1. Insert the foot switch conversion harness (1) into connector <P15> on the main PCB.
2. Connect the connector (2) for the 2-pedal foot switch to the foot switch conversion harness (1).
3. Temporarily remove the screw (4) from the ground terminal of the control box, and then connect the two ground wires (3)
in the 2-pedal foot switch harness to the ground terminal and retighten the screw to the ground terminal.
4. Close the cord presser plate (5) in the direction of the arrow, and secure it by tightening the two screws (6).
NOTE:
・Make sure that the ground connections are secure in order to ensure safety.
・Close the cord presser plate (5) securely so that no foreign objects, insects or small animals can get inside the control
box.
KE-430F, BE-438F
134
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
15. ELECTRIC MECHANISM
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
before opening the face plate of the control box. Touching areas where high voltages are present will result in
serious injury from electric shocks.
15-1. Precautions at the time of adjustment
Pay attention to the following when opening the control box for maintenance.
Electric shock
Some large capacitors may have a high voltage remaining in them for up to 5 minutes after the power is turned off. To prevent
electric shock, wait at least 5 minutes after the power is turned off before doing the following:
• Opening and closing the control box
• Replacing fuses
• Separating and joining connectors
• Measuring resistance
• Doing anything with a possibility of touching something inside the control box
Some adjustments require measuring the voltage while the power is turned on with the control box kept open.
In such a case, be careful not to touch any place other than that for the measurement. In addition, always keep in mind that a
high voltage remains for about 5 minutes after power is turned off.
Injury
When separating or rejoining connectors, and measuring something, be careful not to cut your fingers on metal parts such as
heat sinks and covers.
KE-430F, BE-438F
135
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
15-2. Components inside and outside the control box and in the operation panel
Main PCB
Secured to the rear. This PCB drives the pulse motor and solenoids.
Motor PCB
Secured to the side. This PCB drives the main shaft motor. There are two fuses on this PCB.
Power PCB
Secured to the base. This PCB generates the voltages which are required for control operations.
Conversion transformer box (100V, 110V, 380V, 400V AC specifications only)
Steps-down the power supply voltage and generates the voltages that are required for the control box.
NF box (For Europe)
Eliminates electrical noise that is transmitted along the power supply line.
Panel PCB
Secured inside the operation panel. This PCB controls indications of the machine status and the input operation.
Control box
Operation panel
Main PCB
Panel PCB
Motor PCB
Transformer box
Power PCB
NF box
2682B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
136
15. ELECTRIC MECHANISM
15-3. Fuse explanation
When replacing a fuse, be sure to use the specified ones listed below.
If a component on a PCB is damaged, the fuses may blow again soon even after they have been replaced.
No.
Part name
Fuse 15AFB
(glass tube fuse, 15A-250V)
Part code
When a fuse has blown
F1
F2
The power indicator is not illuminated, and
nothing operates.
A10193-001
Motor PCB
2930B
KE-430F, BE-438F
137
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
15-4. Connectors
Most of the machine trouble is due to connector problems including improper connection or sufficient contact. Therefore, be
sure to check if each connector is correctly inserted and that there is no contact failure between pins and wires before starting
troubleshooting procedures.
15-4-1. Connector positions
Main PCB
2931B
Motor PCB
(Refer to the diagram in “15-3. Fuse explanation”.)
KE-430F, BE-438F
138
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Power PCB
2932B
Panel PCB
2687B
KE-430F, BE-438F
139
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
15-4-2. Contact failure
The connectors functions are divided into five categories. Some connectors may belong to more than one group. Be sure to
investigate another category if a problem is not found in one category.
Feed mechanism
Problem
Connector No. and position
• The work clamp/button clamp operates for a moment but the
home position is not detected correctly.
• Error E200 or E210 is displayed.
2933B
2934B
2935B
• Problem with work clamp/button clamp operation in the
forward-back (Y) direction.
• Error E210, E211, E214, E215 or E216 is displayed.
• Problem with work clamp/button clamp operation in the
sideways (X) direction.
• Error E200, E201, E204, E205 or E206 is displayed.
• The feed motor does not operate for home position detection
immediately after the power is turned on.
• Error E300 is displayed.
2936B
Work clamp mechanism
Problem
Connector No. and position
• The work clamp pulse motor rotates but the home position is not
detected correctly.
• Error E300 is displayed.
2937B
• The work clamp pulse motor does not rotate correctly.
• Error E300, E301, E330 or E331 is displayed.
2938B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
140
15. ELECTRIC MECHANISM
Thread trimmer mechanism
Problem
Connector No. and position
• Thread trimming is not performed. (There is no error display.)
• Digital tension does not operate. (There is no error display.)
• Error E690 is displayed.
2939B
2940B
2941B
Sewing operation
Problem
Connector No. and position
• The power indicator is not illuminated, and nothing operates.
• Machine operation is unstable.
2942B
• The main shaft motor does not operate correctly.
• Error E130 is displayed.
2943B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
141
15. ELECTRIC MECHANISM
Others
Problem
Connector No. and position
• Panel indication is strange.
• The power indicator is not illuminated.
• Any operation panel key does not have any effect.
2944B
• The sewing machine does not operate when the foot switch is
depressed. (No error display.)
2945B
• Error E055 is displayed after the power is turned on.
2946B
• Error E452 is displayed after the power is turned on.
2947B
• The machine does not start up with the “brother” display
appearing.
2948B
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
142
15. ELECTRIC MECHANISM
Problem
Connector No. and position
• Only the power indicator illuminates.
• Nothing appears on the operation panel display.
2949B
• The sewing machine does not operate when the foot switch is
depressed.
• Error E130 is displayed.
2950B
• Error E131 is displayed.
2951B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
143
15. ELECTRIC MECHANISM
15-5. Troubleshooting
15-5-1. Troubleshooting flowchart
Symbols and their meanings
Set-up operation or
condition
Switch operation
The
procedure
to
Yes-or-no
decision-making process
follow continues on the
next page
The error status number
in the first column of the
table of “15-5-2. Problem
solution and measures”
Turning-off
power switch
of
the
2707B
2952B
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
144
15. ELECTRIC MECHANISM
2953B
KE-430F, BE-438F
145
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
2954B
KE-430F, BE-438F
146
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
2955B
KE-430F, BE-438F
147
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
15-5-2. Problem solution and measures
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
before opening the face plate of the control box. Touching areas where high voltages are present will result in
serious injury from electric shocks.
1. Pay attention to the following when opening the control box for maintenance.
Electrical shock
Some large capacitors may have a high voltage remaining in them for up to 5 minutes after the power is turned off.
To prevent electrical shock, wait at least 5 minutes after the power is turned off before doing the following:
• Opening and closing the control box
• Replacing fuses
• Separating and joining connectors
• Measuring resistance
• Doing anything with a possibility of touching something inside the control box
Some adjustments require measuring the voltage while the power is turned on with the control box kept open.
In such a case, be careful not to touch any place other than that for the measurement. In addition, always keep in
mind that a high voltage remains for about 5 minutes after power is turned off.
Injury
When separating or rejoining connectors, and measuring something, be careful not to cut your fingers on metal parts such
as heat sinks and covers.
2. When replacing a fuse, be sure to use a new one of the same quality and capacity as the old one.
Before adjustment
1. While the power is turned off, check each connector is securely plugged in by referring to “15-4. Connectors”.
2. Find the error status number in the troubleshooting flowchart.
3. From the applicable part of the flowchart, take the reference number to find the correspondingly numbered details of the
problem in the following table.
KE-430F, BE-438F
148
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #1 The power indicator does not light when the power is turned on.
Probable causes
1. (Check the LEDs)
Check/ repair/ adjust
Turn on the power switch and check that the
various LEDs illuminate in the following order.
a. LD2 (red) on motor PCB does not illuminate.
→＃1－2、＃1－3、＃1－4
Parts to be replaced
b. LD2 (red) on power PCB does not illuminate.
→＃1－5、＃1－6、＃1－7、＃1－8
c. LD3 (green) on motor PCB does not
illuminate.
→＃1－9
d. Power indicator on panel does not illuminate.
→＃1－10
2. Malfunction of power cord
Disconnect the power supply connector which
links the power cord for the power switch and the
motor PCB, turn on the power switch, and then
measure the voltage between terminals 1 and 3 of
the cord-side connector.
OK if the voltage is the same as mains voltage.
In addition, check that the power supply voltage at
the wall outlet is within the range of the
specification voltage +/- 10%.
After inspecting, turn off the power switch and
connect the power supply connector.
2712B
3. Blown fuse
Remove fuses F1 and F2 from the motor PCB GFUSE15A
and check the continuity.
OK if there is continuity.
(15A-250V)
4. Malfunction of motor PCB 1
Remove P2 (DCIN) from the power PCB, turn the Motor PCB assembly
power back on, and then check LD2 (red) on the
motor PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
five minutes or more, and then insert P2 into the
power PCB.
Turn the power back on, and then with P2
inserted into the power PCB, check the voltage
between terminals 1 and 3 of P2.
OK if 170 to 270 V DC.
5. Malfunction of power PCB
Disconnect connector P1 (POWER2) from the Power PCB assembly
main PCB and connectors P4 (POWER3) and P6
(POWER2) from the motor PCB, and then turn on
the power switch and check LD2 (red) on the
power PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 into the
main PCB and P4 and P6 into the motor PCB.
(Continued on next page.)
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
149
15. ELECTRIC MECHANISM
Error status #1 The power indicator does not light when the power is turned on.
Probable causes
Check/ repair/ adjust
Parts to be replaced
6. Malfunction of main PCB
Disconnect connectors P4 (POWER3) and P6 Main PCB assembly
(POWER2) from the motor PCB, and then turn on
the power switch and check LD2 (red) on the
power PCB.
OK if illuminated.
(LD1 (red) on power PCB does not illuminate)
After checking, turn off the power switch, wait for
one minute or more, and then insert P4 and P6
into the motor PCB.
7. Malfunction of main PCB 2
8. Malfunction of panel PCB
9. Poor harness connection
Disconnect connector P1 (POWER2) from the Motor PCB assembly
main PCB and connectors P1 (MT-ENC), P2
(MAIN) and P3 (PANEL) from the motor PCB, and
then turn on the power switch and check LD2
(red) on the power PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 into the
main PCB and P1, P2 and P3 into the motor PCB.
Disconnect connector P1 (POWER2) from the Panel PCB assembly
main PCB and connectors P1 (MT-ENC) and P2 Panel harness
(MAIN) from the motor PCB, and then turn on the
power switch and check LD2 (red) on the power
PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 into the
main PCB and P1 and P2 into the motor PCB.
Check that connector P4 (POWER3) of the motor Power PCB assembly
PCB is inserted, and then turn on the power
switch and check the voltage between terminals 1
and 4 of P4.
OK if approximately 24 V DC.
2713B
10. Malfunction of operation panel
Check that connector P3 (PANEL) of the motor Operation panel assembly
PCB is inserted.
Panel PCB assembly
Panel harness
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
150
15. ELECTRIC MECHANISM
Error status #2 Error code appears on the display when the power is turned on.
Probable causes Check/ repair/ adjust
1. If “E025” or “E035” is displayed, a. Check if the foot switch is still depressed.
Parts to be replaced
Treadle unit
the foot switch is still depressed.
b. Check if there is a short-circuit in the harness.
c. Check if connector P12 (PEDAL) is connected
to the motor PCB.
d. Reset the depression stroke for the foot switch
while referring to “11-22. Standard setting for
depression stroke (foot switch)”.
* For a 2-pedal foot switch, the connector for the 2-pedal foot switch assembly
main PCB will be P15 (PEDAL).
2. If "E055" is displayed, there is a a. Check if the machine head switch is off.
malfunction of the machine head b. Check if there is a broken wire in the harness.
Switch assembly machine
head
switch.
c. Check if connector P14 (HEAD-SW) is
connected to the main PCB.
3. If "E065" is displayed, one of the a. Check that there is no incorrect sensitivity Operation panel assembly
keys on the operation panel is still
depressed.
when the surface of the panel sheet and the Panel PCB assembly
keys are pressed.
Panel harness
b. Check that connector P3 (PANEL) is
connected to the motor PCB, and that
connector P1 (MAIN) is connected to the
panel PCB.
4. If “E131” is displayed, there is a Check that connector P11 (RESOLVER) and P1
poor
synchronizer.
connection
of
the (MT-ENC) is connected to the motor PCB, and
that connector P6 (MT-ENC) is connected to the
main PCB.
5. If "E400" and "E401" is displayed, a. Check LD3 (green) on the main PCB.
there is connection fault OK if illuminated.
between the main PCB , motor b. Check LD3 (green) on the motor PCB.
PCB and the panel PCB. OK if illuminated.
Main PCB assembly
Motor PCB assembly
Panel PCB assembly
Connection harness
a
c. Check that connector P5 (MOTOR) is Panel harness
connected to the main PCB, and that
connector P2 (MAIN) is connected to the
motor PCB.
d. Check that connector P3 (PANEL) is
connected to the motor PCB, and that
connector P1 (MAIN) is connected to the
panel PCB.
e. Check if there is a broken wire in the harness.
6. If "E450" or "E452" is displayed, a. Check if connector P3 (HEAD-M) is connected
the machine head memory cannot
be recognized.
to the main PCB.
b. Check if there is a broken wire in the harness.
7. If "E700" is displayed, the power a. Check that the power supply voltage at the
supply voltage is abnormally high.
mains is at the specification voltage plus or
minus 10%.
b. See #1-2.
8. If "E705" is displayed, the power a. Check that the power supply voltage at the
supply voltage is abnormally low.
mains is at the specification voltage plus or
minus 10%.
b. See #1-2.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
151
15. ELECTRIC MECHANISM
Error status #3 No keys on the operation panel are not activated.
Probable causes
1. Malfunction of panel PCB
Check/ repair/ adjust
Parts to be replaced
Check that connector P3 (PANEL) is connected to Operation panel assembly
the motor PCB, and that connector P1 (MAIN) is Panel PCB assembly
connected to the panel PCB.
Panel harness
2. Main
software
not
installed Carry out the restore operation by referring to
"7-13. Updating the control program version ".
correctly
Error status #4 Work clamp does not return to the home position even after the foot switch is depressed.
Probable causes
1. Incorrect depression
adjustment
Check/ repair/ adjust
position Adjust the position while referring to “11-22.
Setting method for standard depression strokes
(Foot switch)”.
Parts to be replaced
2. Malfunction of treadle unit
With the motor PCB connector P12 (PEDAL) Foot switch
connected, turn on the power and measure the
voltage between pins 3-4 of the cord connector
(No. 3 +, No. 4 -).
OK if the voltage is approximately 2 V at neutral,
approximately 4 V when the foot switch is
depressed as far as it will go, and approximately
0.5 V when it is depressed backward.
2714B
3. Malfunction of foot switch and cord (Check that the power is turned off.)
(option) Disconnect the foot switch from the foot switch
Foot switch
adapter harness, and measure the voltage
between pins 5-6 and 7-8 of the foot switch
connector. (Check between pins 9-10 if using a
2-pedal foot switch.)
OK if the resistance is normally ∞ ohms but 0
ohms when depressed.
2956B
4. Malfunction of foot switch adapter After checking the foot switch in step 3, connect Foot switch
harness (option)
the foot switch adapter harness to the foot switch Foot switch cord
and measure the voltage between pins 1-2 and
3-4 of connector P15 (PEDAL) of the main PCB.
(Check between pins 5-6 if using a 2-pedal foot
switch.)
(Touch the ohmmeter against the lead wires
without disconnecting the connector.)
OK if the resistance is normally ∞ ohms but 0
ohms when depressed.
2716B
KE-430F, BE-438F
152
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #5 Error code appears on the display when the foot switch is depressed.
Probable causes Check/ repair/ adjust
1. If “E130”, “E131” or “E132” is Refer to inspection #2-4.
displayed, there is poor
connection of the synchronizer.
Parts to be replaced
a
2. If “E130”, “E131” or “E132” is Check the connection of the relay connector
displayed, there is poor between the machine motor and the motor PCB.
connection of the machine motor.
a
3. If “E130”, “E131” or “E132” is a. Remove fuses F1 and F2 from the motor PCB GFUSE15A
displayed, there is a blown fuse.
and check the continuity.
OK if there is continuity.
(15A-250V)
b. If fuse F1 or F2 is blown, check the resistance
values between each pin of the relay
connector between the machine motor and the
motor PCB and between each terminal of the
fuses.
OK if ∞ ohms.
Motor PCB assembly
c. If the fuses blow again after they are replaced,
replace the motor PCB.
4. If “E130”, “E131” or “E132” is a. Check the synchronizer input while referring to Resolver stator 430 assembly
displayed, there is a malfunction of
the motor PCB.
“4-7. Input checking method”.
OK if the signal turns on and off.
b. If step a. (above) is OK, there is a malfunction
of the motor PCB.
Motor PCB assembly
KE-430F, BE-438F
153
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #6 Error code appears on the display when the foot switch is depressed.
Probable causes
Check/ repair/ adjust
Parts to be replaced
1. If the X feed does not move and Disconnect connectors P1 (POWER2) and P24 Power PCB assembly
"E200" is displayed, there is a (POWER1) from the main PCB, and then turn on
malfunction of the power PCB.
the power switch and check LD1 (red) on the
power PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 and P24
into the main PCB.
2. If the X feed does not move and a. Disconnect connector P24 (POWER1) from Main PCB assembly
"E200" is displayed, there is a
malfunction of the main PCB.
the main PCB, and check the continuity
between terminals 1 and 2 of P24.
OK if ∞ ohms.
b. Disconnect connector P21 (XPM) from the
main PCB, and check the continuity between
terminals 1 and 2, 3 and 4 of P21.
OK if ∞ ohms.
c. Insert P21 and P24 into the main PCB, turn on
the power switch and then check LD1 (red) on
the power PCB.
OK if illuminated.
If LD1 is illuminated during the check in step 1
but it does not illuminate when P1 and P24
are connected, there is a malfunction of the
main PCB.
d. Check LD1 (orange) on the main PCB.
OK if illuminated.
2717B
2718B
3. If the X feed moves slightly and a. Check that connector P17 (X-ENC) is inserted Pulse motor X assembly
"E200" is displayed, there is a
malfunction of the encoder.
into the main PCB and that the color matches.
Main PCB assembly
b. Check the encoder input while referring to
"4-7. Input checking method".
4. If the X feed does not move and a. Disconnect the main PCB connector P21 Pulse motor X assembly
"E200" is displayed, there is a
malfunction of the pulse motor and
cord.
(XPM) and measure the resistance between
pins 1-2 and 3-4 of the cord connector.
OK if 2-3 ohms.
b. If step a. (above) is OK, there is a malfunction
of the main PCB.
Main PCB assembly
2719B
KE-430F, BE-438F
154
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #7 Error code appears on the display when the foot switch is depressed.
Probable causes Check/ repair/ adjust
Parts to be replaced
1. If the Y feed does not move and Disconnect connectors P1 (POWER2) and P24 Power PCB assembly
"E210" is displayed, there is a (POWER1) from the main PCB, and then turn on
malfunction of the power PCB.
the power switch and check LD1 (red) on the
power PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 and P24
into the main PCB.
2. If the Y feed does not move and a. Disconnect connector P24 (POWER1) from Main PCB assembly
"E210" is displayed, there is a
malfunction of the main PCB.
the main PCB, and check the continuity
between terminals 1 and 2 of P24.
OK if ∞ ohms.
b. Disconnect connector P22 (YPM) from the
main PCB, and check the continuity between
terminals 1 and 2, 3 and 4 of P22.
OK if ∞ ohms.
c. Insert P22 and P24 into the main PCB, turn on
the power switch and then check LD1 (red) on
the power PCB.
OK if illuminated.
If LD1 is illuminated during the check in step 1
but it does not illuminate when P1 and P24
are connected, there is a malfunction of the
main PCB.
d. Check LD1 (orange) on the main PCB.
OK if illuminated.
2717B
2720B
3. If the Y feed moves slightly and a. Check that connector P18 (Y-ENC) is inserted Pulse motor Y assembly
"E210" is displayed, there is a
malfunction of the encoder.
into the main PCB and that the color matches.
Main PCB assembly
b. Check the encoder input while referring to
"4-7. Input checking method".
4. If the Y feed does not move and a. Disconnect the main PCB connector P22 Pulse motor Y assembly
"E210" is displayed, there is a
malfunction of the pulse motor and
cord.
(YPM) and measure the resistance between
pins 1-2 and 3-4 of the cord connector.
OK if 2-3 ohms.
b. If step a. (above) is OK, there is a malfunction Main PCB assembly
of the main PCB.
2721B
KE-430F, BE-438F
155
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #8 Error code appears on the display when the foot switch is depressed.
Probable causes
Check/ repair/ adjust
Parts to be replaced
1. If the work clamp pulse motor Disconnect connectors P1 (POWER2) and P24 Power PCB assembly
does not operate and "E300" is (POWER1) from the main PCB, and then turn on
displayed, there is a malfunction of the power switch and check LD1 (red) on the
the power PCB.
power PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 and P24
into the main PCB.
2. If the work clamp pulse motor a. Disconnect connector P24 (POWER1) from Main PCB assembly
does not move and "E300" is
displayed, there is a malfunction of
the main PCB.
the main PCB, and check the continuity
between terminals 1 and 2 of P24.
OK if ∞ ohms.
b. Disconnect connector P23 (PPM) from the
main PCB, and check the continuity between
terminals 1 and 2, 3 and 4 of P23.
OK if ∞ ohms.
c. Insert P23 and P24 into the main PCB, turn on
the power switch and then check LD1 (red) on
the power PCB.
OK if illuminated.
If LD1 is illuminated during the check in step 1
but it does not illuminate when P1 and P24
are connected, there is a malfunction of the
main PCB.
d. Check LD1 (orange) on the main PCB.
OK if illuminated.
2717B
2722B
3. If the work clamp pulse motor a. Check that connector P19 (P-ENC) is inserted Pulse motor P assembly
moves slightly and "E300" is
displayed, there is a malfunction of
the encoder.
into the main PCB and that the color matches.
Main PCB assembly
b. Check the encoder input while referring to
"4-7. Input checking method".
4. If the work clamp pulse motor a. Disconnect the main PCB connector P23 Pulse motor P assembly
does not move and "E300" is
displayed, there is a malfunction of
the pulse motor and cord.
(PPM) and measure the resistance between
pins 1-2 and 3-4 of the cord connector.
OK if 2-3 ohms.
b. If step a. (above) is OK, there is a malfunction Main PCB assembly
of the main PCB.
2723B
KE-430F, BE-438F
156
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #9 Error code appears on the display when the foot switch is depressed.
Probable causes Check/ repair/ adjust
1. If "E690" is displayed during home a. Check the position of the thread nipper driving
Parts to be replaced
position detection, there is
malfunction of the thread nipper.
a
lever.
b. Remove any thread scraps from behind the
needle plate.
2. If "E960" is displayed during home Adjust the home position while referring to
position detection, the thread "11-18-3. Thread nipper motor home position".
nipper home position adjustment is
incorrect.
3. If the thread nipper pulse motor Disconnect connectors P1 (POWER2) and P24 Power PCB assembly
does not operate and “E690” is (POWER1) from the main PCB, and then turn on
displayed, there is a malfunction of the power switch and check LD1 (red) on the
the power PCB.
power PCB.
OK if illuminated.
After checking, turn off the power switch, wait for
one minute or more, and then insert P1 and P24
into the main PCB.
4. If the thread nipper pulse motor a. Disconnect connector P1 (POWER2) from the Main PCB assembly
does not move and "E690" is
displayed, there is a malfunction of
the main PCB.
main PCB, and check the continuity between
terminals 1 and 2 of P1.
OK if ∞ ohms.
b. Disconnect connector P4 (TPM) from the main
PCB, and check the continuity between
terminals 1 and 2, 3 and 4 of P4.
OK if ∞ ohms.
c. Insert P1 and P4 into the main PCB, turn on
the power switch and then check LD1 (red) on
the power PCB.
OK if illuminated.
If LD1 is illuminated during the check in step 1
but it does not illuminate when P1 and P24
are connected, there is a malfunction of the
main PCB.
d. Check LD2 (green) on the main PCB.
OK if illuminated.
2717B
2724B
5. If the thread nipper pulse motor a. Check that connector P20 (T-ENC) is inserted Pulse motor T assembly
moves slightly and "E690" is
displayed, there is a malfunction of
the encoder.
into the main PCB and that the color matches.
Main PCB assembly
b. Check the encoder input while referring to
"4-7. Input checking method".
6. If the thread nipper pulse motor a. Disconnect the main PCB connector P4 (TPM) Pulse motor T assembly
does not move and "E690" is
displayed, there is a malfunction of
the pulse motor and cord.
and measure the resistance between pins 1-2
and 3-4 of the cord connector.
OK if 2-3 ohms.
b. If step a. (above) is OK, there is a malfunction Main PCB assembly
of the main PCB.
2725B
KE-430F, BE-438F
157
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #10 Work clamp does not rise.
Probable causes
Check/ repair/ adjust
Parts to be replaced
1. Incorrect work clamp home position a. Adjust the home position while referring to
adjustment
"11-18. Adjusting the home position".
b. Check if the work clamp/button clamp is
touching anything.
2. Incorrect mechanism adjustment
Check if the work clamp arm moves smoothly.
Work clamp arm assembly
Parts to be replaced
Error status #11 Work clamp does not lower.
Probable causes
Check/ repair/ adjust
1. Incorrect work clamp home position a. Adjust the home position while referring to
adjustment
"11-18. Adjusting the home position".
b. Check if the work clamp/button clamp is
touching anything.
2. Incorrect mechanism adjustment
Check if the work clamp arm moves smoothly.
Work clamp arm assembly
Parts to be replaced
Error status #12 The TEST indicator does not light when the TEST key is pressed.
Probable causes
Check/ repair/ adjust
Malfunction of panel PCB
Check that connector P3 (PANEL) is connected to Panel PCB assembly
the motor PCB, and that connector P1 (MAIN) is Panel harness
connected to the panel PCB.
Error status #13 The feed mechanism does not slowly move stitch by stitch during test feeding.
Probable causes
1. Incorrect memory switch setting
Check/ repair/ adjust
Set memory switch No. 200 to OFF.
(The default setting is ON for the BE-438F.)
Parts to be replaced
2. Malfunction of foot switch and cord
See #4.
Error status #14 Quick feeding cannot be performed during test feeding.
Probable causes
Malfunction of foot switch and cord
Check/ repair/ adjust
Parts to be replaced
Parts to be replaced
See #4.
Error status #15 The machine does not operate correctly for the set program during test feeding.
Probable causes
Check/ repair/ adjust
Malfunction of foot switch and cord
See #4.
KE-430F, BE-438F
158
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #16 The machine does not operate during sewing, and the error code [E130], [E131] or [E132] appears on the display.
Probable causes
Check/ repair/ adjust
Parts to be replaced
Malfunction of synchronizer, machine Refer to steps 1 to 4 in #5.
motor, fuses or motor PCB.
Error status #17 Error code appears on the display after the machine operates.
Probable causes
Check/ repair/ adjust
Parts to be replaced
1. If “E111”, “E130”, “E131”, “E132” or Check that connectors P11 (RESOLVER) and P1
“E133” is displayed after the (MT-ENC) of the motor PCB and connector P6
sewing machine operates, there is (MT-ENC) of the main PCB are inserted.
a
poor
connection
of
the
synchronizer.
2. If “E111”, “E130”, “E131”, “E132” or Check the connection of the relay connector
“E133” is displayed after the between the machine motor and the motor PCB.
sewing machine operates, there is
a poor connection of the machine
motor.
3. If “E111”, “E130”, “E131”, “E132” or Check that the ground wire is securely connected
“E133” is displayed after the and that the sewing machine is not close to any
sewing
machine
operates, equipment that generates strong electrical
interference is causing operating interference.
errors.
4. If “E111”, “E130”, “E131”, “E132” or Refer to steps 1 to 4 in #5.
“E133” is displayed after the
Resolver stator assembly
Motor PCB assembly
sewing machine operates, there is
a malfunction of the motor PCB.
5. If "E111", "E130", "E132"or "E133" If an error occurs after inspection steps 1 to 4 Motor 430 assembly
is displayed after the sewing above have been carried out, there is
machine operates, there is malfunction of the machine motor.
a
a
malfunction of the motor PCB or of
the machine motor.
6. If "E121" is displayed after the Check if the blades of the fixed knife and movable
sewing machine operates, there is knife are damaged or worn.
a malfunction of a component.
7. If "E121" is displayed after the Adjust the home position while referring to “11-18.
sewing machine operates, the Adjusting the home position”.
home
position
is
incorrectly
adjusted.
8. If "E121" is displayed after the Refer to steps 3 to 6 in #9.
sewing machine operates, there is
Power PCB assembly
Main PCB assembly
Pulse motor T assembly
a problem with the operation of the
thread nipper pulse motor.
9. If "E121" is displayed after the Refer to steps 3 to 4 in #8.
sewing machine operates, there is
Main PCB assembly
Pulse motor P assembly
a problem with the operation of the
work clamp pulse motor.
(Continued on next page.)
KE-430F, BE-438F
159
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #17 Error code appears on the display after the machine operates.
Probable causes
Check/ repair/ adjust
Parts to be replaced
10. If "E150" is displayed after the a. Turn off the power and let the motor stand for Resolver stator 430 assembly
sewing machine operates, the
motor is abnormally overheating.
30 minutes or more.
Motor PCB assembly
Motor 430 assembly
b. Turn the power back on, and OK if operation
is normal.
c. If the area around the motor is not hot, carry
out steps 1 to 5 in #17.
* Avoid repeated sewing of sewing data that
contains 15 stitches or less.
Error status #18 The machine cannot produce correct stitches.
Probable causes
1. Malfunction of synchronizer
Check/ repair/ adjust
Refer to step 1 in #17.
Parts to be replaced
2. If uneven seams are being sewn, a. Refer to step 4 in #6.
there is a malfunction of the pulse
motor or the mechanism is b. If the uneven seams are due to insufficient
incorrectly adjusted.
work clamp pressure, adjust while referring to
"11-10. Adjusting the work clamp lift amount
(KE-430F)" or "11-11. Adjusting the button
clamp lift amount (BE-438F)".
c. If there is play in the feed mechanism, adjust
the feed mechanism.
KE-430F, BE-438F
160
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #19 The thread trimmer does not operate.
Probable causes
Check/ repair/ adjust
Parts to be replaced
1. Incorrect memory switch setting
Set memory switch No. 164 to OFF.
* If it is set to ON, thread trimming will not be
carried out.
2. Incorrect mechanism adjustment
Adjust the thread trimmer mechanism while
referring to "11-14. Adjusting the thread trimmer
cam position".
* If it seems that the thread trimming mechanism
is not operating properly, carry out steps 3 to 6
below.
3. Poor connector connection
Check that main PCB connector P2 (SOL1) and
P3 (SOL2) is connected.
4. Malfunction of thread trimmer Disconnect main PCB connector P2 (SOL1) and Thread trimmer solenoid
solenoid
measure the resistance between pins 3-6 of the assembly
cord connector.
OK if 6-8 ohms.
2726B
5. Malfunction of tension solenoid
Disconnect main PCB connector P3 (SOL2) and Tension solenoid
measure the resistance between pins 1-2 of the
cord connector.
OK if 6-8 ohms.
2727B
6. Malfunction of main PCB.
a. Turn on the power switch and check LD2 Main PCB assembly
(green) on the main PCB.
OK if illuminated.
b. Turn off the power switch, and with connector
P2 (SOL1) disconnected from the main PCB,
check the continuity between terminals 3 and
6 of connector P2 on the main PCB.
OK if ∞ ohms.
c. With connector P3 (SOL2) disconnected from
the main PCB, check the continuity between
terminals 1 and 2 of connector P3 on the main
PCB.
OK if ∞ ohms.
d. With connector P2 (SOL1) inserted into the
main PCB, turn on the power switch, carry out
sewing and measure the voltage between
terminals 3 and 6 of connector P2.
OK if voltage is output momentarily at the
sewing end.
e. With main PCB connector P3 (SOL2)
connected, turn on the power and carry out
sewing, and measure the voltage between
pins 1-2 of connector P3 (SOL2).
OK if there is voltage output momentarily after
sewing stops.
2728B
KE-430F, BE-438F
161
Download from Www.Somanuals.com. All Manuals Search And Download.
15. ELECTRIC MECHANISM
Error status #20 The machine does not stop at the needle up stop position. (“UP” is frequently displayed after sewing)
Probable causes
1. Incorrect adjustment
Check/ repair/ adjust
Adjust while referring to "11-18. Adjusting the
home position”.
Parts to be replaced
2. Problem with machine motor Refer to steps 1 to 5 in #17
operation
Resolver stator assembly
Motor PCB assembly
Motor 430 assembly
Error status #21 SD card read/write mode cannot be activated.
Probable causes
Check/ repair/ adjust
Parts to be replaced
1. If “E420” is displayed, the SD card a. Check the direction of insertion of the SD
is incorrectly inserted.
card.
(Insert the card so that it matches the direction
of the pattern on the card cover.)
b. Check the insertion of the SD card.
2650B
2. If “E420” is displayed, the SD card Check the format of the SD card.
is incorrectly formatted.
(Carry out 16-sector formatting.)
3. Malfunction of SD card
Use a PC to check if the contents of the SD card
can be read.
4. Malfunction of operation panel
See #12.
Panel PCB assembly
Panel harness
KE-430F, BE-438F
162
Download from Www.Somanuals.com. All Manuals Search And Download.
16. TABLE OF ERROR CODES
16. TABLE OF ERROR CODES
DANGER
Wait at least 5 minutes after turning off the power switch and disconnecting the power cord from the wall outlet
before opening the face plate of the control box. Touching areas where high voltages are present will result in
serious injury from electric shocks.
If a malfunction should occur with the sewing machine, a buzzer will sound and an error code will appear in the display
window. Follow the remedy procedure to eliminate the cause of the problem.
Warnings displayed as symbols
Code
Cause and remedy
The sewing machine started when the work clamp/button clamp was not lowered.
First lower the work clamp/button clamp.
CLdn
The needle bar is not in the needle up stop position.
Turn the pulley until this error display disappears.
UP
Switch-related errors
Code
Cause and remedy
The STOP switch was pressed.
Press the RESET key (*1) to clear the error.
E010
The STOP switch was pressed.
Press the RESET key (*1) to clear the error.
E011
You can press the
key to move the work clamp so that you can continue sewing.
The STOP switch was pressed.
Press the RESET key (*1) to clear the error, and then depress the foot switch to the 2nd step to carry out home
E012
position detection.
The STOP switch was still being pressed when the power was turned on, or there is a problem with the STOP
switch connection.
E015
E016
E025
Turn off the power, and then check that connector P9 on the main PCB is properly connected.
Problem with the STOP switch connection when the power was turned on.
Turn off the power, and then check that connector P9 on the main PCB is properly connected.
The foot switch was depressed to the 2nd step when the power was turned on.
(Start switch for a two-pedal foot switch).
Turn off the power and check the foot switch.
The foot switch was depressed to the 1st step when the power was turned on.
(Work clamp switch for a two-pedal foot switch).
E035
Turn off the power and check the foot switch.
Machine head tilting was detected after the power was turned on.
Turn off the power, and then return the machine head to its original position.
Check that connector P14 on the main PCB is properly connected.
Machine head tilting was detected while the sewing machine was operating.
Turn off the power, and then check that connector P14 on the main PCB is properly connected.
Machine head tilting was detected when the power was turned on.
Turn off the power, and then return the machine head to its original position.
Check that connector P14 on the main PCB is properly connected.
An operation panel key was still being pressed when the power was turned on, or key is faulty.
Turn off the power and check the operation panel.
E050
E051
E055
E065
(*1) If the main PCB version is 1.5.00 or later, press the key or switch which has been set by memory switch No. 650.
KE-430F, BE-438F
163
Download from Www.Somanuals.com. All Manuals Search And Download.
16. TABLE OF ERROR CODES
Upper shaft motor-related errors
Code
Cause and remedy
Sewing machine has continued to be used for a certain period after the “GREASEUP” notification appears
without the grease being applied (without the reset procedure being carried out).
Apply grease and then carry out the reset procedure. (Refer to the service manual for the reset procedure.)
Upper shaft did not stop at the needle up stop position when the sewing machine stopped.
Turn off the power, and then check that there are no problems with the thread trimming mechanism and the
machine motor mechanism.
Thread trimming was not completed.
Turn off the power, and then check if the cutting edges of the fixed knife and movable knife are damaged or worn.
Sewing machine motor stopped abnormally, or synchronizer is faulty.
Turn off the power, and then turn the machine pulley to check if the machine has locked up.
Check that connector P11 on the motor PCB and the 4-pin upper shaft motor connector are properly connected.
Synchronizer is not connected correctly.
Turn off the power, and then check that connector P11 on the motor PCB is properly connected.
Problem detected with sewing machine motor operation.
Turn off the power, and then check that connector P11 on the motor PCB is properly connected.
Sewing machine motor stopping position is incorrect.
Turn off the power, and then check that connector P11 on the motor PCB is properly connected.
E100
E111
E121
E130
E131
E132
E133
Sewing machine motor is overheating, or temperature sensor is faulty.
Turn off the power, and then check the sewing machine motor.
(When sewing data with a small number of stitches (15 stitches or less) is sewn repeatedly (short cycle
E150
operation), the upper shaft motor may overheat and the “E150” error code may be displayed.)
Feed mechanism-related errors
Code
Cause and remedy
X feed motor home position cannot be detected. Problem with X feed motor or poor X encoder connection.
Turn off the power, and then check that connectors P17 and P21 on the main PCB are properly connected.
X feed motor stopped abnormally.
Turn off the power and check that there is no problem with the X feed direction.
X feed motor stopped abnormally during sewing.
Turn off the power and check that there is no problem with the X feed direction.
X-feed motor stopped abnormally while moving to the sewing start position.
Turn off the power and check that there is no problem with the X feed direction.
X feed motor stopped abnormally during test feeding.
Turn off the power and check that there is no problem with the X feed direction.
Y feed motor home position cannot be detected. Problem with Y feed motor or poor Y encoder connection.
Turn off the power, and then check that connectors P18 and P22 on the main PCB are properly connected.
Y feed motor stopped abnormally.
Turn off the power and check that there is no problem with the Y feed direction.
Y feed motor stopped abnormally during sewing.
Turn off the power and check that there is no problem with the Y feed direction.
Y-feed motor stopped abnormally while moving to the sewing start position.
Turn off the power and check that there is no problem with the Y feed direction.
Y feed motor stopped abnormally during test feeding.
E200
E201
E204
E205
E206
E210
E211
E214
E215
E216
Turn off the power and check that there is no problem with the Y feed direction.
Work clamp-related errors
Code
Cause and remedy
Work clamp home position cannot be detected. Problem with work clamp motor or poor work clamp encoder
connection.
Turn off the power, and then check that connectors P19 and P23 on the main PCB are properly connected.
Work clamp/button clamp raised or lowered position cannot be detected.
Turn off the power, and then check that there is no problem with the vertical work clamp/button clamp position.
E300
E301
164
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
16. TABLE OF ERROR CODES
Communication and memory-related errors
Code
Cause and remedy
Communication error detected between the main PCB and the panel PCB when the power was turned on.
Turn off the power, and then check that connector P1 on the panel PCB and connector P3 on the motor PCB are
properly connected.
Communication error detected between the main PCB and the motor PCB when the power was turned on.
Turn off the power, and then check that connector P5 on the main PCB and connector P2 on the motor PCB are
properly connected.
E400
E401
Communication error between main PCB and panel PCB detected.
Turn off the power, and then turn it back on again.
Communication error between main PCB and motor PCB detected.
Turn off the power, and then turn it back on again.
No media is inserted.
E410
E411
E420
Press the RESET key (*1) to clear the error.
Data contents are incorrect and cannot be used, or no data.
Press the RESET key (*1) to clear the error.
Check that data for this pattern number is present in the media.
Error occurred while reading from media.
Press the RESET key (*1) to clear the error.
Check the data in the media.
Insufficient space in media.
Press the RESET key (*1) to clear the error.
E421
E422
E424
Use different media.
Error occurred while writing to media.
Press the RESET key (*1) to clear the error.
Use the specified type of media.
E425
Check if the media is write-protected and if it has enough free space.
A pattern registered in a cycle program has been erased.
Press the RESET key (*1) to clear the error.
Re-register the cycle program, or add the pattern.
A pattern registered in a program has been erased.
Press the RESET key (*1) to clear the error.
E427
E428
Re-register the program, or add the pattern.
Data cannot be backed up to main PCB.
Turn off the power, and then turn it back on again.
Data memory error on main PCB.
Turn off the power, and then turn it back on again.
Model selection has not been loaded from the machine head memory.
Turn off the power and check that connector P16 on the main PCB is properly connected.
Machine head memory is not connected.
Turn off the power, and then check that connector P16 on the main PCB is properly connected.
Internal memory is full and copying is not possible.
Press the RESET key (*1) to clear the error.
E430
E440
E450
E452
E474
Clear any unnecessary additional patterns.
(*1) If the main PCB version is 1.5.00 or later, press the key or switch which has been set by memory switch No. 650.
KE-430F, BE-438F
165
Download from Www.Somanuals.com. All Manuals Search And Download.
16. TABLE OF ERROR CODES
Data editing-related errors
Code
Cause and remedy
The enlargement ratio setting caused the sewing data to extend outside the sewing area.
Press the RESET key (*1) to clear the error.
Set the enlargement ratio or the sewing area again.
The enlargement ratio caused the data pitch to exceed the maximum pitch of 12.7 mm.
Press the RESET key (*1) to clear the error.
Set the enlargement ratio again.
Error in pattern data.
E500
E502
E510
E511
E512
Press the RESET key (*1) to clear the error.
Re-read the pattern data from the media, or recreate the pattern data.
No end code has been input into pattern data.
Press the RESET key (*1) to clear the error.
Recreate the pattern data containing the end code, or change the pattern number being read.
Number of stitches exceeds allowed maximum.
Press the RESET (*1) key to clear the error.
Change the number of the pattern being read.
Memory switch file cannot be read correctly.
Copy source model and copy destination model are incorrect. (Maybe the 430F is attempting to read data for the
438F.)
E581
Press the RESET key (*1) to clear the error.
Read data for the same sewing machine model.
Memory switch version does not match.
Press the RESET (*1) key to clear the error.
Read data for the same version.
Parameter version does not match.
E582
E583
Press the RESET key (*1) to clear the error.
Read data for the same version.
(*1) If the main PCB version is 1.5.00 or later, press the key or switch which has been set by memory switch No. 650.
Device-related errors
Code
Cause and remedy
Upper thread breakage occurred.
Press the RESET key (*1) to clear the error.
E600
Thread nipper motor home position cannot be detected. Problem with thread nipper motor or poor thread nipper
encoder connection.
Turn off the power, and then clean underneath the needle plate to remove any dust and thread scraps.
Check that connector P20 on the main PCB is properly connected.
Thread nipper motor stopped abnormally.
E690
E692
Check if the upper thread trailing length is too long.
Turn off the power, and then clean underneath the needle plate to remove any dust and thread scraps.
Check that connectors P20 and P4 on the main PCB are properly connected.
(*1) If the main PCB version is 1.5.00 or later, press the key or switch which has been set by memory switch No. 650.
166
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
16. TABLE OF ERROR CODES
PCB-related errors
Code
Cause and remedy
Abnormal rise in power supply voltage.
Turn off the power and check the input voltage.
Abnormal rise in sewing machine motor drive voltage.
Turn off the power, and then check the voltage.
Abnormal drop in power supply voltage.
Turn off the power and check the input voltage.
Abnormal current detected in sewing machine motor.
Turn off the power, and then check if there are any problems with the sewing machine.
Abnormal current detected in pulse motor.
Turn off the power, and then check if there are any problems with the work clamp/button clamp operation.
E700
E701
E705
E710
E711
Version update errors
Code
Cause and remedy
No control program is present.
Repeat the version update procedure.
Version update requests cannot be received.
Turn off the power, and then turn it back on again.
E870
E880
E881
Version updating did not complete normally.
Turn off the power, and then repeat the version update procedure.
Communication error between main PCB and panel PCB detected.
Turn off the power, and then check that connector P1 on the panel PCB, connector P5 on the main PCB and
connectors P2 and P3 on the motor PCB are properly inserted.
No control program is present on the SD card.
Check that the control program has been saved into the correct folder.
There is a problem with the control program.
E882
E883
E884
Save the correct file onto the SD card.
E885
-887
Version updating could not be carried out.
Turn off the power, and then turn it back on again.
If an error code that is not listed above appears or if carrying out the specified remedy does not solve
the problem, contact the place of purchase.
KE-430F, BE-438F
167
Download from Www.Somanuals.com. All Manuals Search And Download.
17. TROUBLESHOOTING
17. TROUBLESHOOTING
• Please check the following points before calling for repairs or service.
• If the following remedies do not fix the problem, turn off the power switch and consult a qualified technician or the place of
purchase.
CAUTION
Turn off the power switch and disconnect the power cord before carrying out troubleshooting, otherwise the
machine may operate if the foot switch is depressed by mistake, which may result in injury.
Problem
Cause
Remedy
Ref.
Work clamp does not
rise. (KE-430F)
Grease the sliding part of the work
clamp.
Work clamp operation is sluggish.
P. 112
Too much friction between work clamp
lifter plate and work clamp arm lever
plate.
Grease the work clamp lifter plate and
work clamp arm lever plate.
P. 112
Work clamp is contacting thread wiper.
Work clamp is contacting thread wiper.
Adjust the position of the thread wiper.
Adjust the position of the thread wiper.
Adjust the work clamp lift amount.
P. 114
P. 114
P. 112
Button clamp does not
rise. (BE-438F)
Work clamp lift amount
is incorrect. (KE-430F)
Incorrect position of work clamp arm
lever plate
Button clamp lift
amount is incorrect.
(BE-438F)
Incorrect position of button clamp holder
hook.
Adjust the button clamp lift amount.
Adjust the height of the thread wiper.
P. 112
P. 114
P. 114
P. 114
Thread wiper does not
operate correctly.
The thread wiper is obstructing the
needle.
Adjust the operating distance of the
thread wiper.
Adjust the operating distance of the
thread wiper.
Thread wiper position is incorrect.
CD
Instruction
manual
Lower thread winds to
one side.
Height of bobbin winder tension Adjust the height of the bobbin winder
assembly is incorrect.
tension assembly.
CD
Instruction
manual
Lower thread winding
amount is incorrect.
Adjust the position of the bobbin
presser.
Bobbin presser position is incorrect.
Thread comes
unthreaded.
Stitches being skipped at the sewing
start.
Refer to “Skipped stitches occur”
Adjust the sub-tension.
P. 169
CD
Instruction
manual
Uneven needle thread.
CD
Instruction
manual
Needle thread is too short.
Use a thread nipper device.
168
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
17. TROUBLESHOOTING
Problem
Cause
Remedy
Ref.
CD
Instruction
manual
Upper thread breaks.
Upper thread tension is too strong.
Adjust the upper thread tension.
CD
Instruction
manual
Needle is installed incorrectly.
Install the needle correctly.
Thread is too thick for the needle.
Use the correct thread for the needle.
P. 103
P. 105
Thread take-up spring tension and Adjust the tension and height of the
height are incorrect. thread take-up spring.
Damaged or burred rotary hook, needle File smooth or replace the affected
hole plate or needle.
part.
CD
Instruction
manual
Thread melting (synthetic thread)
Use the needle cooler.
CD
Instruction
manual
Lower thread breaks.
Lower thread tension is too strong.
Adjust the lower thread tension.
Corners of needle hole plate or bobbin File smooth or replace the affected
case are damaged.
part.
Skipped stitches occur.
Clearance between needle and rotary
hook tip is too great.
Adjust the needle clearance.
P. 107
P.107
P. 107
Incorrect needle and rotary hook timing. Adjust the needle bar lift amount.
Driver is contacting needle more than is
Adjust the driver needle guard.
necessary.
Needle is bent.
Replace the needle.
CD
Instruction
manual
Needle is installed incorrectly.
Install the needle correctly.
Adjust the needle clearance.
Adjust the needle bar lift amount.
Replace the needle.
Needle breaks.
P. 107
P. 107
Needle is touching the rotary hook.
Needle is bent.
Needle is too thin.
Use the correct needle for the material.
Refer to “5-5. Checking the sewing
P. 103
CD
Instruction
manual
Needle is striking the button. (BE-438F) pattern (BE-438F)” in the CD instruction
manual.
Button breaks.
(BE-438F)
Refer to “5-5. Checking the sewing
pattern (BE-438F)” in the CD instruction
manual.
CD
Instruction
manual
Needle is striking the button.
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
169
17. TROUBLESHOOTING
Problem
Cause
Remedy
Ref.
Upper thread is not
trimmed.
Movable knife is blunt.
Replace the movable knife.
P. 111
Fixed knife is blunt.
Sharpen or replace the fixed knife.
P. 111
P. 108
P. 107
P. 169
P. 110
Adjust the position of the shuttle race
thread guide.
Movable knife does not pick up the
thread.
Adjust the needle bar lift amount.
The movable knife does not pick up the
thread because of skipped stitches at Refer to “Skipped stitches occur”.
the sewing end.
Adjust the position of the movable
Movable knife position is incorrect.
knife.
CD
Instruction
manual
Turn the sub-tension nut to adjust the
Sub-tension is too weak.
tension.
Thread jamming.
Thread take-up spring tension and Adjust the tension and height of the
P. 105
P. 107
P. 108
P. 108
height are incorrect.
thread take-up spring.
Incorrect needle and rotary hook timing. Adjust the needle bar lift amount.
Shuttle race thread guide is not Adjust the position of the shuttle race
separating the threads.
thread guide.
Poor seam finish on
Shuttle race thread guide is separating Adjust the position of the shuttle race
reverse
side
of
the threads insufficiently.
thread guide.
material.
CD
Instruction
manual
Upper thread is not properly tight.
Adjust the upper thread tension.
CD
Instruction
manual
Uneven needle thread.
Adjust the sub-tension.
Adjust the sub-tension.
CD
Instruction
manual
<When using the thread nipper
device>
Turn the tension nut to adjust the upper
thread trailing length to 35 – 38 mm.
Needle thread is too long.
Refer to “5-5. Checking the sewing
Needle is striking the button. (BE-438F) pattern (BE-438F)” in the CD instruction
manual.
CD
Instruction
manual
CD
Incorrect thread
tightness.
Instruction
manual
Upper thread tension is too weak.
Lower thread tension is too weak.
Adjust the upper thread tension.
Adjust the lower thread tension.
CD
Instruction
manual
Thread take-up spring tension and Adjust the tension and height of the
P. 105
height are incorrect.
thread take-up spring.
CD
Instruction
manual
Machine does not
operate when power is
turned on and foot
Check if the machine head switch cord
is disconnected.
switch is depressed.
Adjust the position of the switching
plate.
Machine head switch does not work.
P. 127
Replace the machine head switch if it is
broken.
170
KE-430F, BE-438F
Download from Www.Somanuals.com. All Manuals Search And Download.
18. 7-SEGMENT DISPLAY LIST
18. 7-SEGMENT DISPLAY LIST
4268M
KE-430F, BE-438F
171
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
KE-430F, BE-438F
172
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
KE-430F, BE-438F
173
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE MANUAL
KE-430F, BE-438F
I0070967B
© 2011 Brother Industries, Ltd. All Rights Reserved.
2011.04. B (2)
Download from Www.Somanuals.com. All Manuals Search And Download.
|