®
®
®
®
®
®
Absolute COLOR
•
Absolute BLACK • Unidrums • Unirollers • Uniparts • Unicoatings
™
BROTHER HL 1240 • 1650 (TN 430/460)
CARTRIDGE REMANUFACTURING INSTRUCTIONS
®
BROTHER HL 1650
LASER PRINTER
TN 430 TONER CARTRIDGE
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Summit Technologies is a division of UniNet Imaging Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
1. With the use of small flat blade screwdriver, slightly pry up the
white plastic alignment hub located from the non-gear side of
the developer roller and remove it.
2. NOTE: Be aware of the pressure spring behind the white plas-
tic hub and do not lose it.
NOTES
3. On the same side and with the help of a small jeweler screw-
driver release the three (3) clips holding the developer roller
bearing cap to the toner hopper. The first clip is right below the
screw holding the developer blade, the opposite clip is between
the side of the roll and the casing while the third one is accessi-
ble from outside the casing.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGE
4. With a small flat blade screwdriver, pry the bearing cap off the
developer roller axle and the fixing post.
5. Move to the other side of the cartridge and above the white
plastic hub on the gear side, locate the clip that holds the devel-
oper roller cap-bearing. NOTE: Contrary to the other bearing cap
this one is located between the developer roller and the side of
the cartridge.
NOTES
6. Press the clip in towards the developer roller and rotate the
piece up towards the front of the toner hopper, until the bearing
cap is perpendicular to the roller.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UNINET IMAGING INC. • BROTHER 1240/1650 • DISASSEMBLING THE TONER CARTRIDGE
7. Lift the developer roller from the hopper. NOTE: Clean the roller
using a clean lint free cloth. DO NOT USE any solvent or chemi-
cals on the developer roller.
8. Remove the fill plug from the hopper.
9. Discharge any toner from the toner hopper. Use dry com-
pressed air or a vacuum to THOROUGHLY clean out the toner
hopper. Clean the developer blade using a dry lint free cloth.
NOTES
NOTE: DO NOT attempt to re-use any of the toner remaining in
the cartridge and DO NOT complete the charge by adding new or
unused toner from another old cartridge.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UNUINNIENTETIMIAMGAIGNIGNGINICN.C.•• BRBORTOHTEHRER1214204/01/6156050 •• DIASSASSESMEBMLBILNIGNGTHTEHETOTNOENRERCACRATRRTIRDIGDEGE
10. Reassemble cartridge in reverse order.
11. Recap the hopper securely.
Fill cartridge with the adequate load of new toner for 3000 pages
in the TN-430 (110 grams) or 6000 pages in the TN-460 (210
grams).
NOTES
12. Insert the OEM or the compatible yellow seal cover for the
developer roller to protect it during transit.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UNUINNIENTETIMIAMGAIGNIGNGINICN.C.•• BRBORTOHTEHRER1214204/01/6156050 •• DIASSASSESMEBMLBILNIGNGTHTEHETOTNOENRERCACRATRRTIRDIGDEGE
2
1
3
OPC CARTRIDGE
13. With a medium size Phillips screwdriver remove the screws
securing the corona wire assembly. There are two in each corner
holding the plastic top and one, visible thru the hole on the right
hand side securing the electric contact of the control grid and
the cleaning felt.
3
1
4
2
14. Press the four tabs to remove the assembly from the top of
the cartridge starting from the two behind followed by the ones
on each side.
15. Clean the grid surface of any toner with compressed air.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UUNUNINNIINENETETTIMIIMAMGAAGIGNIINGNGGINIINCNC.C..••• BBRBROROTOHTTHEHERERR11212424040/01//16165650500 ••• DDIASISASSAESMESBEMMLBIBLNILGNINGTGHTEHTHETEOTNOENPRECRCCAACRRATTRRRTIRIDDIGDGEGEE
1
2
16. Finish with a dry lint-free cloth.
17. With a Phillips screwdriver remove the screws holding the
drum cleaning assembly. You will notice that it is composed of a
cleaning felt, a recovery blade and a couple of scraper-blades.
18. Remove and clean the assembly thoroughly removing all
remains of old toner.
19. Remove the shaft of the drum by releasing the retaining
washer from the left side of the cartridge.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UUNUNINNIINENETETTIMIIMAMGAAGIGNIINGNGGINIINCNC.C..••• BBRBROROTOHTTHEHERERR11212424040/01//16165650500 ••• DDIASISASSAESMESBEMMLBIBLNILGNINGTGHTEHTHETEOTNOENPRECRCCAACRRATTRRRTIRIDDIGDGEGEE
20. Pull axle out using a pair of needle-nose pliers.
21. Slide the axle away from the cartridge as shown.
22. When the drum is extracted there will be a spring loaded
clutch piece at one end and a drive gear on the other side com-
ing loose.
23. Do not lose these three pieces which will be needed to
assemble the cartridge even if a new drum is installed.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UUNUNINNIINENETETTIMIIMAMGAAGIGNIINGNGGINIINCNC.C..••• BBRBROROTOHTTHEHERERR11212424040/01//16165650500 ••• DDIASISASSAESMESBEMMLBIBLNILGNINGTGHTEHTHETEOTNOENPRECRCCAACRRATTRRRTIRIDDIGDGEGEE
24. NOTE: There is also a plastic stabilizer bearing for the axle
located on the same side of the clutch gear which must be
secured.
25. Extract the transfer roller from the cartridge using a pair of
long nose pliers. Notice that the saddles and the helical gear
will also come out. Clean the roller with compressed air or vacu-
um cleaner. DO NOT USE any solvent or chemicals on the trans-
ference roller.
NOTES
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UNUIUNNNIENITNEETITMIAMIGMAIGANGIGNINGIGNICNI.NC.C•. ••BRBOBRTROHOTEHTRHEER1R21412024/4010/61/516065500•••DIASSAASSESSEMEMBMBLBILLNIINGNGGTHTTHEHEETOTNOPECNRECRACRACTRARTRRITDIRDGIGDEEGE
26. Replace the transfer roller together with its saddles and the
helical gear.
27. Replace the OPC drum by mounting the clutch and spring on
the right side and engage the drive gear on the left. NOTE: Before
inserting the axle lift the spring loaded contact wire located
between the drive gear of the OPC and the side of the cartridge.
29. Insert the drum cleaning assembly and with a Phillips screw-
driver and tighten the screws to secure it to the cartridge. The
screw on the left will pressure the contact between the assem-
bly and the drum axle.
28. Slide the axle from left to right, insert the bearing in place
and the retaining washer to secure the axle in place.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNINET IMAGING INC. • BROTHER HL 1240/165 (TN 430/460) CARTRIDGE REMANUFACTURING INSTRUCTIONS
UNUIUNNNIENITNEETITMIAMIGMAIGANGIGNINGIGNICNI.NC.C•. ••BRBOBRTROHOTEHTRHEER1R21412024/4010/61/516065500•••DIASSAASSESSEMEMBMBLBILLNIINGNGGTHTTHEHEETOTNOPECNRECRACRACTRARTRRITDIRDGIGDEEGE
30. With a Tester check the electrical continuity between the
contact of the assembly and the drum shaft.
31. Insert the lid containing the corona assembly, align the four
clips, and press down to clamp it.
NOTES
32. Tighten the external screws and finally the small internal
one.
www.uninetimaging.com/technical.asp
11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • [email protected]
© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.
Download from Www.Somanuals.com. All Manuals Search And Download.
|