Quick Setup Guide
HL-4570CDW
HL-4570CDWT
Start Here
Before using this machine for the first time, read this Quick Setup Guide to setup and install your machine.
Note
Not all models are available in all countries.
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injuries.
WARNING
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injuries.
CAUTION
Unpack the machine and check the components
1
Drum Unit
Waste Toner Box
Belt Unit
(pre-installed)
(pre-installed)
(pre-installed)
Documentation/Installation CD-ROM(s)
Quick Setup Guide
Starter Toner Cartridges
(pre-installed)
(Black, Cyan, Magenta and
Yellow)
Safety and Legal Booklet
AC Power Cord
ENG Version 0
1
Download from Www.Somanuals.com. All Manuals Search And Download.
d
e
Hold the green handle of the drum unit a and
pull it out until it stops.
Remove the packing
material from the
machine
2
IMPORTANT
DO NOT connect the AC power cord yet.
a
Remove the packing tape from the outside of
the machine.
b
Open the MP tray a, and remove the plastic
sheet b from the MP tray support, then close
the MP tray.
Hold the orange packing material, and remove
it.
c
Press the front cover release button and open
the front cover. Remove the silica gel pack a.
f
Remove the 4 orange packing pieces.
CAUTION
DO NOT eat Silica Pack. Discard immediately.
g
h
Push the drum unit firmly back into the
machine.
Close the front cover of the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
d
Put paper in the tray and make sure:
The paper is below the maximum paper
mark (bbb) a.
Load paper in the paper
tray
3
Over filling the paper tray will cause paper
jams.
a
b
Pull the paper tray completely out of the
machine.
The side to be printed on must be face down.
The paper guides touch the sides of the
paper so it will feed properly.
While pressing the green paper-guide release
lever a, slide the paper guides to fit the paper
size you are loading in the tray. Make sure that
the guides are firmly in the slots.
e
Put the paper tray firmly back in the machine.
Make sure that it is completely inserted into the
machine.
For more information about recommended
paper, see Recommended paper and print
media in the User's Guide.
c
Fan the stack of paper well to avoid paper jams
and misfeeds.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
d
Press Go. The machine will print a test page.
Check that the test page has printed correctly.
Print a test page
4
IMPORTANT
DO NOT connect the interface
cable yet.
a
Connect the AC power cord to the machine and
then connect it to an AC power outlet.
b
Remove the label covering the machine's
power switch, and then switch the machine on.
Note
This function will not be available after the first
print job you send from your computer.
c
After the machine has finished warming up, the
LCD will show Ready.
Note
You can adjust the angle of the display by lifting it.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Set your language
5
a
Press + or - to choose General Setup.
Press OK.
b
c
Press OK to choose Local Language.
Press + or - to choose your language.
Press OK.
Now go to
Next page to install the printer driver.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Choose your connection type
6
For USB Interface Users
Macintosh, go to page 9
For Wired Network
Macintosh, go to page 14
For Wireless Network
Windows® and Macintosh,
go to page 16
Note
You can download the latest drivers and utilities for your machine from the Brother Solutions Center at
7
Download from Www.Somanuals.com. All Manuals Search And Download.
®
USB
Windows
For USB Interface Cable Users for Windows®
Note
Before you install
®
®
• For Windows Vista and Windows 7 users,
when the User Account Control screen
appears, click Allow or Yes.
7
• If you want to install the PS driver (BR-Script3
printer driver), choose Custom Install and then
follow the on-screen instructions.
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
IMPORTANT
c
d
Follow the on-screen instructions until this
screen appears.
• If there are any programs running, close
them.
• The screens may differ depending on your
operating system.
b
Turn off the machine and make sure the USB
interface cable is NOT connected to the
machine, and then begin installing the printer
driver. If you have already connected the cable,
disconnect it.
Connect the USB cable to the USB connector
on the machine marked with the
symbol,
and then connect the cable to your computer.
Install the printer driver
8
e
Turn the machine on, and follow the on-screen
instructions to complete setup.
a
Put the installation CD-ROM into your
CD-ROM drive. If prompted, select your model
and language.
The installation is now
Finish
complete.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
Note
• Depending on your security settings, a
Windows Security or antivirus software window
may appear when using the machine or its
software. Please allow or permit the window to
continue.
b
Click Install Printer Driver, and click Yes if
you accept the license agreement.
• XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is
the most suitable driver when printing from the
applications that use the XML Paper
Specification documents. Please download the
latest driver by accessing the Brother Solutions
8
Download from Www.Somanuals.com. All Manuals Search And Download.
USB
Macintosh
For USB Interface Cable Users for Macintosh
Before you install
Install the printer driver
7
8
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
a
b
Put the installation CD-ROM into your
CD-ROM drive.
Double-click the Start Here OSX icon. Follow
the on-screen instructions.
IMPORTANT
For Mac OS X 10.4.10 users, upgrade to
Mac OS X 10.4.11 - 10.6.x. (For the latest
drivers and information on the Mac OS X you
Note
If you want to setup the PS driver (BR-Script3
printer driver), please go to the Brother Solutions
Downloads on your model page to download the
driver and visit FAQ's for installation instructions.
Note
It may take a few minutes for installation to
complete.
c
Follow the on-screen instructions until this
screen appears. Choose your machine from
the list, and then click OK.
b
Connect the USB cable to the USB connector
on the machine marked with the symbol,
and then connect the cable to your Macintosh.
d
When this screen appears, click Next.
c
Make sure the machine power switch is on.
Note
When the Brother Support screen appears,
make your selection and follow the on-screen
instructions.
The installation is now
complete.
Finish
9
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Wired Network
Windows
For Wired Network Interface Cable Users for Windows®
(For Peer-to-Peer network users)
c
Connect the network interface cable to the LAN
connector marked with a symbol and then
Before you install
7
connect it to a free port on your hub.
TCP/IP
TCP/IP
d
a
Make sure the machine power switch is on.
a Router
b Machine
Install the printer driver
Note
If you are going to connect the machine to your
network, we recommend that you contact your
system administrator prior to installation.
8
Put the installation CD-ROM into your
CD-ROM drive. If prompted, select your model
and language.
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
IMPORTANT
• If there are any programs running, close
them.
• The screens may differ depending on your
operating system.
b
Click Install Printer Driver, and click Yes if
you accept the license agreement.
b
Remove the protective cap from the LAN
connector.
Note
®
®
• For Windows Vista and Windows 7 users,
when the User Account Control screen
appears, click Allow or Yes.
• If you want to install the PS driver (BR-Script3
printer driver), choose Custom Install and then
follow the on-screen instructions.
c
Follow the on-screen instructions to complete
setup.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Wired Network
Windows
Note
You can find your machine’s IP Address and the
node name by printing out the Printer Settings
Page. See Print the Printer Settings
The installation is now
complete.
Finish
Note
• If you use a specified IP Address for the
machine, you must set the Boot Method to
Static by using the control panel. For more
information, see Network menu in the Network
User's Guide.
• Depending on your security settings, a
Windows Security or antivirus software window
may appear when using the machine or its
software. Please allow or permit the window to
continue.
• XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is
the most suitable driver when printing from the
applications that use the XML Paper
Specification documents. Please download the
latest driver by accessing the Brother Solutions
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Wired Network
Windows
For Wired Network Interface Cable Users for Windows®
(For shared network users)
Before you install
Install the printer driver
7
8
a
Put the installation CD-ROM into your
CD-ROM drive. If prompted, select your model
and language.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
TCP/IP
b
Click Install Printer Driver, and click Yes if
you accept the license agreement.
a Client computer
b Also known as “Server” or “Print server”
c TCP/IP or USB
d Machine
Note
If you are going to connect the machine to your
network, we recommend that you contact your
system administrator prior to installation.
Note
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
®
®
• For Windows Vista and Windows 7 users,
when the User Account Control screen
appears, click Allow or Yes.
IMPORTANT
• If you want to install the PS driver (BR-Script3
printer driver), choose Custom Install and then
follow the on-screen instructions.
• If there are any programs running, close
them.
• The screens may differ depending on your
operating system.
c
Follow the on-screen instructions until this
screen appears. Choose your machine’s
queue, and then click OK.
b
Make sure the machine power switch is on.
Note
Contact your administrator if you do not know the
location or the name of the machine queue on the
network.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Wired Network
Windows
d
Follow the on-screen instructions to complete
setup.
The installation is now
complete.
Finish
Note
• Depending on your security settings, a
Windows Security or antivirus software window
may appear when using the machine or its
software. Please allow or permit the window to
continue.
• XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is
the most suitable driver when printing from the
applications that use the XML Paper
Specification documents. Please download the
latest driver by accessing the Brother Solutions
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Wired Network
Macintosh
For Wired Network Interface Cable Users for Macintosh
Before you install
Install the printer driver
7
8
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
a
b
Put the installation CD-ROM into your
CD-ROM drive.
Double-click the Start Here OSX icon. Follow
the on-screen instructions.
IMPORTANT
For Mac OS X 10.4.10 users, upgrade to
Mac OS X 10.4.11 - 10.6.x. (For the latest
drivers and information on the Mac OS X you
Note
If you want to setup the PS driver (BR-Script3
printer driver), please go to the Brother Solutions
Downloads on your model page to download the
driver and visit FAQ's for installation instructions.
Note
It may take a few minutes for installation to
complete.
c
Follow the on-screen instructions until this
screen appears. Choose your machine from
the list, and then click OK.
b
Remove the protective cap from the LAN
connector.
Note
• If there is more than one of the same model
connected on your network, the MAC Address
(Ethernet Address) will be displayed after the
model name.
c
d
Connect the network interface cable to the LAN
connector marked with a
symbol and then
connect it to a free port on your hub.
• You can find your machine’s MAC Address
(Ethernet Address) and IP Address by printing
out the Printer Settings Page. See Print the
d
When this screen appears, click Next.
Make sure the machine power switch is on.
Note
When the Brother Support screen appears,
make your selection and follow the on-screen
instructions.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Wired Network
Macintosh
The installation is now
complete.
Finish
Note
If you use a specified IP Address for the machine,
you must set the Boot Method to Static by using
the control panel. For more information, see
Network menu in the Network User's Guide.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
For Wireless Network Interface Users
Before you begin
7
First you must configure the wireless network settings of your machine to communicate with your network access
point/router. After the machine is configured to communicate with your access point/router, computers on your
network will have access to the machine. To use the machine from these computers, you will need to install the
printer driver. The following steps will guide you through the configuration and installation process.
IMPORTANT
• If you are going to connect the machine to your network, we recommend that you contact your
system administrator prior to installation. You must know your wireless network settings before you
proceed with this installation.
• If you have previously configured the wireless settings of the machine, you must reset the print
server back to its factory default settings.
1. On your machine, press + or - to choose Network, and press OK.
2. Press + or - to choose Network Reset, and press OK.
3. Press + to choose Reset. When Reboot OK? appears, press + to choose Yes.
Note
• To achieve optimum results with normal everyday document printing, place the Brother machine as close to
the network access point/router as possible with minimal obstructions. Large objects and walls between the
two devices as well as interference from other electronic devices can affect the data transfer speed of your
documents.
Due to these factors, wireless may not be the best method of connection for all types of documents and
applications. If you are printing large files, such as multi-page documents with mixed text and large graphics,
you may want to consider choosing wired Ethernet for a faster data transfer or USB for the fastest throughput
speed.
• Although the Brother HL-4570CDW(T) can be used in both a wired and wireless network, only one of the
connection methods can be used at a time.
Infrastructure Mode
a Access point/router
b Wireless Network machine (your machine)
c Wireless capable computer connected to
the access point/router
d Wired computer connected to the access
point/router
16
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
Confirm your network environment (Infrastructure Mode)
8
The following instructions will offer two methods for installing your Brother machine in a wireless network
environment.
Note
To setup your machine in any other wireless environment, you can find instructions in the Network User's
Guide.
a
If your WLAN access point/router supports automatic wireless mode
(Wi-Fi Protected Setup or AOSS™)
Now go to
b
If your WLAN access point/router does not support Wi-Fi Protected Setup or AOSS™, write down
the wireless network settings of your WLAN access point/router.
IMPORTANT
Please do not contact Brother Customer Service for assistance without the wireless security
information. We cannot assist you in locating your network security settings.
Network name (SSID/ESSID)
Network Key
For example:
Network name (SSID/ESSID)
HELLO
Network Key
12345678
Note
• If you do not know this information (Network Name (SSID/ESSID) and Network Key), you cannot
continue the wireless setup.
• How can I find this information (Network Name (SSID/ESSID) and Network Key)
1. You should see the documentation provided with your WLAN access point/router.
2. The initial network name could be the manufacturer’s name or the model name.
3. If you do not know the security information, please consult the router manufacturer, your system
administrator or internet provider.
Now go to
17
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
Connecting the Brother machine to the wireless network
Wireless setup is now complete. A four
Configure the wireless
settings using the
automatic wireless mode
level indicator at the right of your
machine’s LCD will show the wireless
signal strength of your access
point/router.
9
a
Confirm your WLAN access point/router has
the Wi-Fi Protected Setup or AOSS™ symbol
as shown below.
To install the printer driver, continue to
®
For Windows Users:
Now go to
b
c
Place the Brother machine within range of your
Wi-Fi Protected Setup or AOSS™ access
point/router. The range may differ depending
on your environment. Refer to the instructions
provided with your access point/router.
For Macintosh Users:
Now go to
On your machine, press + or - to choose
Network and press OK.
Press + or - to choose WLAN and press OK.
Press + or - to choose WPS/AOSS and press
OK.
When WLAN Enable? is displayed, press + to
accept. This will start the wireless setup wizard.
Otherwise press Cancel to exit from the
wireless setup wizard.
When Press Key on rtr appears, press
the Wi-Fi Protected Setup or AOSS™ button
on your WLAN access point/router. See the
user’s guide for your WLAN access point/router
for instructions. And then press +.
This feature will automatically detect which
mode (Wi-Fi Protected Setup or AOSS™) your
access point/router uses to configure your
machine.
Note
If your WLAN access point/router supports Wi-Fi
Protected Setup (PIN Method) and you want to
configure your machine using the PIN (Personal
Identification Number) Method, see Using the PIN
Method of Wi-Fi Protected Setup in the Network
User's Guide.
d
A connection result message appears on the
LCD and a WLAN report will automatically be
printed.
If the connection failed, check the error code on
the printed report and refer to
18
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
c
Enter the Network Key you wrote down in
To enter a letter or number, hold down or
repeatedly press the + or - key until the letter
you want appears, and then press OK.
Configure the wireless
settings (typical Wireless
Setup in infrastructure
mode)
9
To delete the letters you have entered, press
the Back key.
IMPORTANT
You must have the wireless settings you
page 17 before you proceed.
For more information, see Entering Text for
Press OK when you have entered all the
characters, then press OK for Yes to apply
a
On your machine, press + or - to choose
Network and press OK.
Press + or - to choose WLAN and press OK.
Press + or - to choose Setup Wizard and
press OK.
d
e
Your machine will now try to connect to your
wireless network using the information you
have entered.
A connection result message appears on the
LCD and a WLAN report will automatically be
printed.
When WLAN Enable? is displayed, press + to
accept. This will start the wireless setup wizard.
Otherwise press Cancel to exit from the
wireless setup wizard.
If the connection failed, check the error code on
the printed report and refer to
b
The machine will search for available SSIDs. If
a list of SSIDs is displayed, use the + or - key
Wireless setup is now complete. A four
level indicator at the right of your
machine’s LCD will show the wireless
signal strength of your access
point/router.
If you are using an authentication and
encryption method that requires a Network
To install the printer driver, continue to
If your authentication method is Open System
If your WLAN access point/router supports
Wi-Fi Protected Setup, WPS is available
appears. Press +. To connect your machine
using the automatic wireless mode, press + to
the Network Key.) When Press WPS on rtr
appears, press the Wi-Fi Protected Setup
button on your WLAN access point/router, and
®
For Windows Users:
Now go to
For Macintosh Users:
Now go to
Note
• It will take several seconds to display a list of
available SSIDs.
• If a list of SSIDs is not displayed, make sure
your access point is on. Move your machine
closer to the access point and try starting from
a again.
If you use your machine in an IEEE 802.1x
supported wireless network, see Using IEEE
802.1x authentication in the Network User's
Guide.
If your access point is set to not broadcast the
SSID you will have to manually add the SSID
name. For details, see Configuring your
machine when the SSID is not broadcast in the
Network User's Guide.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
Troubleshooting
IMPORTANT
Please do not contact Brother Customer Service for assistance without the wireless security
information. We cannot assist you in locating your network security settings.
How can I find the wireless settings (Network Name (SSID/ESSID) and Network Key)
1. You should see the documentation provided with your WLAN access point/router.
2. The initial network name could be the manufacturer’s name or the model name.
3. If you do not know the security information, please consult the router manufacturer, your system
administrator or internet provider.
* The Network Key may also be described as the Password, Security Key or Encryption Key.
* If the WLAN access point/router is set to not broadcast the SSID, the SSID will not automatically be detected.
You will have to manually enter the SSID name. See Configuring your machine when the SSID is not broadcast
in the Network User's Guide.
WLAN report
If the WLAN report that printed shows that the connection failed, check the error code on the printed report and
refer to the following instructions.
Error code
Recommended Solutions
The wireless setting is not activated, turn the wireless setting to ON.
- If a LAN cable is connected to your machine, disconnect it and turn the wireless setting of
your machine to ON.
1. On your machine, press + or - to choose Network and press OK.
2. Press + or - to choose WLAN and press OK.
TS-01
3. Press + or - to choose Setup Wizard and press OK.
4. When WLAN Enable? is displayed, press + to accept. This will start the wireless setup
wizard.
The WLAN access point/router cannot be detected.
1. Check the following 4 points.
- Make sure that the WLAN access point/router is powered on.
- Move your machine to an obstruction-free area, or closer to the wireless access
point/router.
- Temporarily place your machine within about one meter (3.3 feet) from the WLAN
access point when you are configuring the wireless settings.
TS-02
- If your WLAN access point/router is using MAC address filtering, confirm the MAC
address of the Brother machine is allowed in the filter.
2. If you manually entered the SSID and security information (SSID/authentication
method/encryption method/Network Key) the information may be incorrect.
Reconfirm the SSID and security information and reenter the correct information as
necessary.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
Error code
Recommended Solutions
The wireless network and security setting you entered may be incorrect.
Reconfirm the wireless network settings.
* Check if the entered or selected SSID/authentication method/encryption
method/UserID/Userpass are correct.
TS-03
The Authentication/Encryption methods used by the selected WLAN access point/router are
not supported by your machine.
For infrastructure mode, change the authentication and encryption methods of the WLAN
access point/router. Your machine supports the following authentication methods WPA,
WPA2, OPEN and Shared key. WPA supports TKIP or AES encryption methods. WPA2
supports AES for the encryption method. OPEN and Shared key correspond to WEP
encryption.
If your problem is not solved the SSID or network settings you entered may be incorrect.
Reconfirm the wireless network settings.
Combined table of authentication and encryption methods
Authentication method
WPA-Personal
WPA2-Personal
OPEN
Encryption method
TS-04
TKIP
AES
AES
WEP
NONE (without encryption)
WEP
Shared key
For ad-hoc mode, change the authentication and encryption methods of your computer for
the wireless setting.
Your machine supports OPEN authentication method only, with optional WEP encryption.
The security information (SSID/Network Key) is incorrect.
Reconfirm the SSID and security information (Network Key).
If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother
machine supports the use of the first WEP key only.
TS-05
The wireless security information (Authentication method/Encryption method/Network Key)
is incorrect.
Reconfirm the wireless security information (Authentication method/Encryption
method/Network Key) in the table of TS-04.
TS-06
If your router uses WEP encryption, enter the key used as the first WEP key. Your Brother
machine supports the use of the first WEP key only.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
For Wireless Network Users
Error code
Recommended Solutions
The machine cannot detect a WLAN access point/router that has WPS or AOSS™ enabled.
If you would like to configure your wireless settings using WPS or AOSS™, you must operate
both your machine and the WLAN access point/router.
Confirm your WLAN access point/router supports WPS or AOSS™ and try starting again.
TS-07
If you do not know how to operate your WLAN access point/router using WPS or AOSS™,
see the documentation provided with your WLAN access point/router, ask the manufacturer
of your WLAN access point/router or ask your network administrator.
Two or more WLAN access points that have WPS or AOSS™ enabled are detected.
- Confirm that only one WLAN access point/router within range has the WPS or AOSS™
method active and try again.
TS-08
- Try starting again after a few minutes in order to avoid interference from other access
points.
Entering Text for Wireless Settings
Hold down or repeatedly press the + or - key to select a character from the list below:
(space) !"#$%&'()*+,-./0123456789:;<=>?@
ABCDEFGHIJKLMNOPQRSTUVWXYZ[?]^_\abcdefghijklmnopqrstuvwxyz{|}~
Press the Back key to delete the letters you have entered.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Wireless Network
Windows
Install the Printer Driver for Windows®
Note
Before you install
If you want to install the PS driver (BR-Script3
printer driver), choose Custom Install and then
follow the on-screen instructions.
10
a
Make sure that your computer is ON and you
are logged on with Administrator rights.
d
Choose your machine from the list, and then
click Next.
IMPORTANT
• If there are any programs running, close
them.
• The screens may differ depending on your
operating system.
b
Make sure the machine power switch is on.
IMPORTANT
DO NOT cancel any of the screens during the
installation.
Install the printer driver
11
e
Follow the on-screen instructions to complete
setup.
a
Put the installation CD-ROM into your
CD-ROM drive. If prompted, select your model
and language.
The installation is now
Finish
complete.
Note
If the Brother screen does not appear
automatically, go to My Computer (Computer),
double-click the CD-ROM icon, and then
double-click start.exe.
Note
• If you use a specified IP Address for the
machine, you must set the Boot Method to
Static by using the control panel. For more
information, see Network menu in the Network
User's Guide.
b
Click Install Printer Driver, and click Yes if
you accept the license agreement.
• Depending on your security settings, a
Windows Security or antivirus software window
may appear when using the machine or its
software. Please allow or permit the window to
continue.
• XML Paper Specification Printer Driver
The XML Paper Specification Printer Driver is
the most suitable driver when printing from the
applications that use the XML Paper
Specification documents. Please download the
latest driver by accessing the Brother Solutions
Note
®
®
For Windows Vista and Windows 7 users,
when the User Account Control screen
appears, click Allow or Yes.
c
Choose Wireless Network Connection.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Network
Macintosh
Install the Printer Driver for Macintosh
IMPORTANT
DO NOT cancel any of the screens during the
installation.
Before you install
10
a
Make sure your machine is connected to the
power and your Macintosh is ON. You must be
logged on with Administrator rights.
Note
It may take a few minutes for installation to
complete.
IMPORTANT
d
Choose your machine from the list, and then
click OK.
For Mac OS X 10.4.10 users, upgrade to
Mac OS X 10.4.11 - 10.6.x. (For the latest
drivers and information on the Mac OS X you
Note
If you want to setup the PS driver (BR-Script3
printer driver), please go to the Brother Solutions
Downloads on your model page to download the
driver and visit FAQ's for installation instructions.
Note
• If there is more than one of the same model
connected on your network, the MAC Address
(Ethernet Address) will be displayed after the
model name.
Install the printer driver
• You can find your machine’s MAC Address
(Ethernet Address) and IP Address by printing
out the Printer Settings Page. See Print the
11
a
Put the installation CD-ROM into your
CD-ROM drive.
e
When this screen appears, click Next.
b
Double-click the Start Here OSX icon. Follow
the on-screen instructions.
Note
When the Brother Support screen appears,
make your selection and follow the on-screen
instructions.
c
Choose Wireless Network Connection.
The installation is now
complete.
Finish
Note
If you use a specified IP Address for the machine,
you must set the Boot Method to Static by using
the control panel. For more information, see
Network menu in the Network User's Guide.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
For Network Users
Web Based Management
(web browser)
Reset the network settings to the
factory default
The Brother print server is equipped with a web server
that allows you to monitor its status or change some
of its configuration settings, using HTTP (Hyper Text
Transfer Protocol).
To reset all network settings of the print server to its
factory default, follow the steps below.
a
b
Press + or - to choose Network.
Press OK.
Note
• The login name for the Administrator is ‘admin’
(case sensitive) and the default password is
‘access’.
Press + or - to choose Network Reset.
Press OK.
®
• We recommend Microsoft Internet
c
d
Press + to choose Reset.
®
Explorer 6.0 (or greater) or Firefox 3.0 (or
greater) for Windows and Safari 3.0 (or
®
Press + to choose Yes for reboot.
greater) for Macintosh. Please also make sure
that JavaScript and Cookies are always
enabled in whichever browser you use. To use
a web browser, you will need to know the IP
Address of the print server. The IP Address of
the print server is listed on the Print Setting
Page.
The machine will re-start.
Print the Printer Settings Page
The Printer Settings Page lists all the current printer
settings, including network settings.
a
b
Open your browser.
a
b
Press + or - to choose Machine Info..
Press OK.
your browser (where machine_ip_address
is the IP address or the print server name).
Press OK to choose Print Settings.
Note
If the IP address on the Printer Settings Page
shows 0.0.0.0, wait for one minute and try again.
See Web Based Management in the Network
User's Guide.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Color Correction (if needed)
Color Calibration
The output density for each color may vary depending
on the environment the machine is in, such as
temperature and humidity. Calibration helps you to
improve the color density.
Color Registration
Auto Registration
You can adjust the print position of each color
automatically.
a
b
Press + or - to choose Color Correction.
Press OK.
Note
Press + or - to choose Auto Regist..
Press OK.
• If you print using the Direct Print feature or the
BR-Script printer driver, you need to perform
the calibration from the control panel. See
c
d
Press OK to choose Registration.
Press + to choose Yes.
®
• If you print using the Windows printer driver,
the driver will get the calibration data
To adjust the print position of each color
manually, see Manual Registration in the
User's Guide.
automatically if both Use Calibration Data and
Get Device Data Automatically are on. See
Advanced tab in the User's Guide.
• If you print using the Macintosh printer driver,
you need to perform the calibration using
Status Monitor. After turning Status Monitor
on, choose Color Calibration from Control
menu. See Color Calibration in the User's
Guide.
Brother CreativeCenter Icon
Get inspired. Double-click the Brother CreativeCenter
icon on your desktop to access a FREE web site with
many ideas and resources for personal and
professional use.
Using the control panel
a
b
Press + or - to choose Color Correction.
Press OK.
Press + or - to choose ColorCalibration.
Press OK.
c
d
Press OK to choose Calibrate.
Press + to choose Yes.
You can reset the calibration parameters back to
those set at the factory.
a
b
c
d
Press + or - to choose Color Correction.
Press OK.
Press + or - to choose ColorCalibration.
Press OK.
Press + or - to choose Reset.
Press OK.
Press + to choose Reset.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Options and Consumables
Options
The machine has the following optional accessories. You can expand the capabilities of the machine by adding
these items. For more information about the optional Lower Tray Unit and compatible SO-DIMM Memory, visit us
For installing the SO-DIMM Memory, see Installing extra memory in the User's Guide.
Lower Tray Unit for HL-4570CDW (LT-300CL)
SO-DIMM Memory
Second lower paper tray unit can hold up to
500 sheets of paper. When the tray is installed, the
machine expands total input capacity up to
800 sheets.
You can increase the memory by installing one
SO-DIMM (Small Outline Dual In-line Memory
Module).
Consumables
When the time comes to replace consumable items, an error will be indicated by the LCD on the control panel. For
more information about the consumables for your machine, visit us at http://solutions.brother.com/ or contact your
local Brother reseller.
Toner cartridges
Drum unit
Belt Unit (BU-300CL)
Waste Toner Box (WT-300CL)
For replacing the consumable items, see Replacing consumable items in the User's Guide.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Microsoft, Windows, Windows Server and Internet Explorer are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
Windows Vista is either a registered trademark or a trademark of Microsoft Corporation in the United States and other countries.
Apple, Macintosh, Safari and TrueType are trademarks of Apple Inc., registered in the United States and other countries.
Wi-Fi and Wi-Fi Alliance are registered trademarks of the Wi-Fi Alliance.
AOSS is a trademark of Buffalo Inc.
Any trade names and product names of companies appearing on Brother products, related documents and any other
materials are all trademarks or registered trademarks of those respective companies.
Compilation and Publication
Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and
specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for
any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other
errors relating to the publication.
Copyright and License
©2010 Brother Industries, Ltd.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC.
©2010 Devicescape Software, Inc.
This product includes the “KASAGO TCP/IP” software developed by ZUKEN ELMIC, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|