Broilmaster Gas Grill AND P48 User Manual

CART, POST, AND BASE  
OWNERS MANUAL  
DC, PC, PB, U26, U26SS, U48, AND P48 MODELS  
OUTDOOR GRILL MOUNTINGS FOR PROPANE AND NATURAL GAS  
®
FOR USE WITH BROILMASTER PREMIUM GAS GRILLS  
FOR OUTDOOR USE ONLY  
RETAIN OWNERS MANUAL FOR FUTURE REFERENCE.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
1
CONGRATULATIONS!  
You have chosen the finest grill for your outdoor cooking pleasure. Please take time to read  
this entire manual before assembling your premium Broilmaster® accessory.  
C22  
Important Information............................................................................................................2  
Cart and Patio Base (DC, PC and PB Models)............................................................3-8  
Patio Post (U26 and U26SS Models) .........................................................................9-13  
In-Ground Post (U48 and P48 Models).......................................................................14-18  
Warranty .............................................................................................................20-21  
Your Broilmaster® accessory is identified by model number, serial number, and gas  
type. This information is provided on a product identification label located on the  
accessory. The grill’s model number, serial number, and gas type must also be provided  
when contacting your Broilmaster® dealer. For your convenience, complete this section  
for future reference when contacting your dealer.  
Grill Information  
Model No.  
Dealer  
Serial No.  
Dealer Phone No.  
Date of Purchase  
Gas Type: Propane  
Natural  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT INFORMATION  
Grill Location  
2
Gas Types  
Broilmaster® Premium Gas Grills are designed  
for outdoor use ONLY.  
Never use liquid propane gas with a grill  
designed for natural gas, or natural gas with a  
grill designed for liquid propane gas. The type  
of gas required for your grill is defined on its  
product identification label. Questions  
regarding different types of gases should be  
directed to your gas supplier.  
These mounting accessories are designed for  
use with Broilmaster® gas grills and must not  
be used with any other grill or for any other  
purpose.  
Never install or operate your grill in any building,  
garage, or other enclosed area.  
Cleaning  
For your safety, the grill should not be installed  
or operated under any combustible materials,  
such as carports, covered porches, awnings,  
or overhangs.  
The exterior of your cart or post may be cleaned  
with hot water and mild detergent as needed.  
Touch-up paint is available through your  
Broilmaster® dealer.  
Never install or use your grill in or on any  
recreational vehicle or boat.  
Stainless steel surfaces may be cleaned with a  
spray-on stainless steel cleaner available at most  
hardware stores.  
CAUTION: THE INSTALLATION AND OPERATION OF  
THIS GRILL AT CLEARANCES LESS THAN SPECIFIED  
BELOW MAY LEAD TO THE POSSIBILITY OF FIRE,  
PROPERTY DAMAGE, OR PERSONAL INJURY.  
Important:  
Do not use harsh or abrasive  
cleaners! Your cart or post has a highly polished  
surface and may be easily scratched.  
A minimum clearance of sixteen (16) inches is  
required from all sides of the grill to any  
combustible material.  
PERIODIC INSPECTION  
MAINTENANCE  
Periodic inspections and maintenance are  
essential. All Broilmaster® Gas Grill products or  
mechanical devices eventually begin to wear  
due to environment, contaminants, corrosion or  
aging. Inspect all components at least twice per  
year and replace any that show wear.  
AND  
A minimum clearance of eighteen (18) inches is  
required from the back of the grill to any combustible  
material.  
Examples of combustible materials are patio  
furniture, fences, or the wall of your home.  
The area surrounding the grill should be clear  
to ensure proper ventilation. Do not obstruct  
the flow of combustion and ventilation air in any  
way. The ventilation openings on the propane  
cylinder enclosure must also remain free and  
clear of debris.  
If any parts are damaged or missing, you may  
order parts from your local Broilmaster® dealer.  
Please refer to the Parts Diagram and Parts List  
section of this manual for more detailed  
information.  
WARNING: DO NOT INSTALL OR OPERATE A GAS  
GRILL WHERE GASOLINE OR OTHER FLAMMABLE  
MATERIALS ARE USED OR STORED. FAILURE TO COMPLY  
WITH THIS WARNING COULD RESULT IN EXPLOSION OR  
FIRE CAUSING PROPERTY DAMAGE OR PERSONAL INJURY.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PC, DC CART AND PB BASE  
INSTALLATION INSTRUCTIONS  
VERIFY THAT ALL PARTS LISTED ON THE EXPLODED VIEW OF THIS MANUAL HAVE BEEN  
INCLUDED IN THIS CART BEFORE BEGINNING INSTALLATION.  
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.  
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.  
KEEP THIS OWNERS MANUAL FOR FUTURE REFERENCE.  
EMPIRE COMFORT SYSTEMS, INC 918 FREEBURG AVE. BELLEVILLE, IL 62220 618-233-7420  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
CART EXPLODED VIEW  
13  
1
2
3
14  
15  
16  
17  
4
5
18  
19  
6
7
20  
8
9
21  
22  
10  
23  
24  
11  
12  
REMOVE PROTECTIVE COATING AND VERIFY THAT ALL PARTS LISTED ON THE EXPLODED VIEW  
OF THIS MANUAL HAVE BEEN INCLUDED BEFORE BEGINNING ASSEMBLY.  
CAUTION: USE CAUTION WHEN HANDLING PARTS, AS THEY MAY CONTAIN SHARP EDGES.  
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.  
TOOLS REQUIRED: PHILLIPS SCREW DRIVER (AN ELECTRIC SCREW DRIVER OR DRILL IS  
RECOMMENDED TO EASE INSTALLATION.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CART PARTS LIST  
5
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in  
your area, contact Broilmaster Customer Service at (618) 233-7420. To ensure prompt and accurate  
service, please provide the following information when placing a repair part order: Model Number,  
Part Name, Part Number, and Quantity of parts needed.  
Key  
No.  
1
2
3
4
5
6
7
PC  
DC  
PB  
Qty.  
1
3
1
1
1
1
1
1
2
1
2
2
2
2
17  
1
1
Part Name  
Drip Pan Drawer  
Wing Nut  
Part No.  
072206  
063097  
076782  
064791  
072221  
072178  
072163  
063103  
072232  
063104  
9130020  
063106  
060337  
HD388  
072217  
072201  
072215  
076783  
076537  
072212  
N/A  
Part No.  
072211  
072181  
076785  
064791  
072222  
072191  
072187  
063103  
072234  
063104  
9130020  
073271  
060337  
HD577  
072220  
072203  
072215  
076787  
076537  
072213  
N/A  
Part No.  
072206  
063097  
076782  
064791  
072221  
072178  
072164  
N/A  
N/A  
N/A  
N/A  
N/A  
060337  
HD388  
072217  
072201  
072215  
076783  
076537  
072212  
070492  
N/A  
Left Assembly  
Cylinder Retainer  
Control Housing  
Front Assembly  
Base Assembly  
Caster with out Brake  
Caster Pad  
Caster with Brake  
Hub Cap  
Hub Cap Cover  
Drip Pan  
10-24x3/8 Phillips Truss Screw  
1/4-20x3/4 Phillips Truss Screw  
Rear Brace  
Drip Pan Bracket  
Right Assembly  
10-32x1/2 Phillips Screw  
Base Channel  
Tie Down Plate  
Axle  
8" Wheel  
8
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
1
6
2
1
1
2
1
063107  
063105  
906236  
063107  
073272  
906236  
N/A  
906236  
Burner Stabilizer Kit*  
*See your grill manual for instructions on how to install the Burner Stabilizer.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
CART ASSEMBLY  
1
FIGURE 1  
Tip: To aid in the assembly process , you may be  
asked to leave certain screws loose until later in  
the assembly process. Please pay close attention  
to each step to determine if you should tighten  
screws at that time.  
1/8"  
Caution: Be careful when handling parts, as  
they may contain sharp edges. Work gloves  
are recommended to prevent injury.  
19  
Insert six #10-32 x 1/2 phillips screws (19) into  
the factory installed clip nuts on the front assembly  
(6). Leave an 1/8" gap beneath the head of the  
3
6
screws as shown by Figure 1.  
Attach front assembly (6) to base (7) with two ˘-20  
x 3/4 phillips screws (15). Figure 2. Do not tighten  
screws at this time.  
FIGURE 2  
2
Fasten side assemblies (3,18) to the front  
assembly (6) by aligning the keyholes on the side  
panels to the three screws installed by Step 1, on  
the front panel, then push down.  
6
15  
Attach the side assemblies to the base (7) with  
two ˘-20 x 3/4 phillips screws. Do not tighten  
screws at this time.  
7
FIGURE 3  
2
17  
3
16  
15  
Attach drip pan bracket (17) to the cart with  
two ˘-20 x 3/4 phillips screws (15) and two ˘-  
20 Wing Nuts (2). Figure 3.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
CART ASSEMBLY  
4
15  
FIGURE 4  
Attach the Rear Brace (16) to the Left and  
Right Side Assemblies with four ˘-20 x 3/4  
screws (15). Figure 4.  
16  
Important: Completely tighten all screws  
at this time.  
FIGURE 5  
5
Install one 1/4-20 x 3/4 phillips screw (15) into  
the factory installed nut on the Left SideAssembly.  
2
Fasten the Cylinder Retainer (4) to the screw with  
a wing nut (2). Adjust height to accommodate  
your LP cylinder. Figure 5.  
4
15  
6
FIGURE 6  
Slide the flanges of the Control Housing (5) behind  
the opening. Allow the Control Housing to rest at  
the bottom of the opening. Figure 6.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
CART ASSEMBLY  
7
15  
FIGURE 7  
Using four ˘-20 x 3/4 screws (15), fasten the  
grill to the cart. Figure 7.  
Note: To ease assembly you may wish to install  
the igniter as shown in your Broilmaster® grill  
manual before attaching the grill to the cart.  
8
FIGURE 8  
Align the holes in the front with the nuts on the  
control housing (5) (with flanges positioned inside  
cart) and fasten with two 10-24 x 3/8 phillips head  
screws (14). Place the drip pan (13) in the drip  
pan drawer (1) and slide onto drip pan bracket  
(17). Figure 8.  
13  
5
1
14  
PB Model: Tie down plate (21) provided to anchor  
post base to patio or deck. Hardware not included.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
U26 AND U26SS PATIO BASE POST  
INSTALLATION INSTRUCTIONS  
1
2
3
4
5
6
3
2
1
7
5
8
2
3
1
WARNING: THIS IN-GROUND POST IS NOT DESIGNED FOR USE WITH AN LP GAS CYLINDER.  
KEEP THIS OWNERS MANUAL FOR FUTURE REFERENCE.  
EMPIRE COMFORT SYSTEMS, INC. 918 FREEBURG AVE. BELLEVILLE, IL 62220 618-233-7420  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
PATIO BASE POST PART LIST  
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer in  
your area, contact Broilmaster Customer Service at (618) 233-7420. To ensure prompt and accurate  
service, please provide the following information when placing a repair part order: Model Number,  
Part Name, Part Number, and Quantity of parts needed.  
U26 PART  
NUMBER  
U26SS PART  
NUMBER  
ITEM  
NUMBER  
QTY.  
16  
12  
16  
4
PART NUMBER  
HD504  
HD545  
HD197  
HD170  
HD125  
878517P  
HD009  
826468  
HD242  
896076P  
HD427  
076518  
065821  
248x6x6  
HD504  
HD545  
HD197  
HD170  
063096  
070283  
HD009  
826468  
HD242  
064854  
068182  
076518  
065821  
248x6x6  
1
2
9/32 ID x 5/8 OD FLAT WASHER  
1/4 LOCK WASHER  
3
1/4-20 HEX NUT  
4
1/4-20 x 1-3/4" EYEBOLT  
1/4-20 x 3/4" BOLT  
8
5
1
6
26" SQUARE POST  
4
7
1/4-20 x 4" EYEBOLT  
1
8
CAST IRON PATIO BASE  
10-24 WING NUT  
1
9
1
10  
11  
12  
13  
14  
CONTROL HOUSING  
2
#10 SCREW/PANEL FASTENER  
STAINLESS STEEL FLEX TUBE ASSEMBLY  
GREASE CUP BRACKET ASSEMBLY  
MALE FLARE FITTING  
1
1
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
PATIO BASE POST ASSEMBLY  
11  
The U26 and U26SS Patio Base Posts are only  
2
for use with Broilmaster® Gas Grills. Before  
proceeding with installation read the Owners  
Manual for the proper location and minimum  
clearances to combustible materials for your grill  
and patio base post.  
Fasten the bottom of the post to the cast iron patio  
base using flat washers (1), lock washers (2), and  
nuts (3). FIGURE 2.  
Anchor the base to your patio using the two holes  
provided in the base. (Hardware not included)  
Verify that all parts listed in the exploded view of  
this product have been included before beginning  
this installation.  
Note: Make sure that the large rectangular cut out  
is facing in the direction that you want your grill to  
face. FIGURE 2.  
Recommended Tools:  
FIGURE 2  
Two adjustable wrenches or a socket set  
A medium Phillips screwdriver  
Pipe thread sealer or Teflon tape (for gas  
connections)  
Soapy water solution (to test for leaks)  
1
Attach four ˘-20 x 4" eyebolts (7) to the bottom of  
the square post using hex head bolts (5), flat  
washers (1), lock washers (2), and nuts (3).  
Figure 1.  
NOTE: The large rectangular cut out is located at  
the front of the post near the top.  
8
1
2
3
FIGURE 1  
3
Insert the flex tubing into the post.  
The inlet side of the gas tubing may protrude from  
the bottom of the patio base or through the large  
circular hole in the back of the square post.  
Note: Do not attempt to cut or alter the flex tube in  
any way.  
3
2
5
1
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PATIO BASE POST ASSEMBLY  
4
Fasten the four ˘-20 x 13/4" short eyebolts (4) to  
the top of the square post using hex head bolts  
(5), flat washers (1), lock washers (2), and nuts  
(3).  
12  
THE GRILL MUST BE ISOLATED FROM THE GAS SUPPLY  
PIPING SYSTEM BY CLOSING ITS INDIVIDUAL MANUAL  
SHUTOFF VALVES DURING ANY PRESSURE TESTING OF  
THE GAS SUPPLY PIPING SYSTEM AT TEST PRESSURES  
EQUAL TO OR LESS THAN ˚ PSIG.  
Position the grill head onto the eyebolts and fasten  
with lock washers (2) and nuts (3). FIGURE 3.  
FIGURE 3  
3
2
12  
FIGURE 4  
4
GRILL  
BOTTOM  
WARNING: DO NOT SUPPLY LP GAS TO A GRILL  
DESIGNED FOR NATURAL GAS OR NATURAL GAS TO A  
GRILL DESIGNED FOR LP GAS.  
6
6
5
Attach the retainer bracket to the slide with a wing  
nut as shown by Figure 5.  
Arrange with your local gas company to have a  
gas supply line connected to the inlet of the flex  
tube. The gas supply must have a shutoff valve  
inside the wall and must be shutoff when the grill  
is not in use.  
FIGURE 5  
13  
13  
Use pipe thread sealant or Teflon tape at the  
threads of each connection being careful to not  
allow any of these materials into the flare seat.  
Test for gas leaks as directed by the grills Owner  
Manual.  
9
9
THE GRILL AND ITS INDIVIDUAL SHUTOFF VALVES MUST  
BE DISCONNECTED FROM THE GAS SUPPLY PIPING  
SYSTEM DURING ANY PRESSURE TESTING OF THAT  
SYSTEM AT TEST PRESSURES IN EXCESS OF ˚ PSIG.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PATIO BASE POST ASSEMBLY  
7
13  
FIGURE 6  
Attach the bracket and slide assembly to the  
factory installed screw located in the bottom of the  
grill housing. Figure 6.  
Loosen the wing nut and move the slide up or  
down to accept the grease cup. Be sure to trap the  
rim of the cup as shown.  
Use only noncombustible containers for the  
grease cup (aluminum or tin cans) do not use  
combustible containers such as Styrofoam or  
paper cups.  
FIGURE 7  
8
Attach the control housing (10) using two #8 x 1/2  
screws (11) or two plastic panel fasteners as  
shown in Figure 7.  
10  
1
11  
11  
9
Continue assembly as directed by the Owners  
Manual packaged with the grill head.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
U48 AND P48 IN-GROUND POST  
INSTALLATION INSTRUCTIONS  
1
3
2
4
5
6
7
WARNING: THIS IN-GROUND POST IS NOT DESIGNED FOR USE WITH AN LP GAS CYLINDER.  
WARNING: SEE YOUR GRILL OWNERS MANUAL FOR PROPER LOCATION, MINIMUM CLEARANCES, AND  
OTHER IMPORTANT SAFETY INFORMATION BEFORE PROCEEDING WITH INSTALLATION OF THIS IN-  
GROUND POST.  
KEEP THIS OWNERS MANUAL FOR FUTURE REFERENCE.  
EMPIRE COMFORT SYSTEMS, INC. 918 FREEBURG AVE. BELLEIVLLE, IL 62220 618-233-7420  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IN-GROUND POST PARTS DIAGRAM  
15  
All repair part orders should be placed through your local Broilmaster® dealer. To locate a dealer  
in your area, contact Broilmaster® Customer Service at (618) 233-7420. To ensure prompt and  
accurate service, please provide the following information when placing a repair part order: Model  
number of your Side Burner, Part Name, Part Number, and Quantity of parts needed.  
U48 PART  
NUMBER  
P48 PART  
NUMBER  
ITEM  
NUMBER  
QTY.  
PART NUMBER  
HD504  
HD582  
HD197  
HD170  
HD125  
076519  
825615P  
896076P  
HD427  
248x6x6  
065821  
HD504  
HD582  
HD197  
HD170  
063096  
076519  
064573  
064854  
068182  
248x6x6  
065821  
1
2
4
8
8
4
4
1
1
1
2
1
1
1/4 FLAT WASHER  
1/4 LOCK WASHER  
3
1/4-20 HEX NUT  
4
1/4-20x1 3/4" EYEBOLT  
1/4-20x3/4" BOLT  
5
6
STAINLESS STEEL FLEX TUBE ASSEMBLY  
48" POST  
7
8
CONTROL HOUSING  
#8 SCREW/PLASTIC PANEL FASTENER  
MALE FLARE FITTING  
GREASE CUP ASSEMBLY  
9
10  
VERIFY THAT ALL PARTS LISTED IN THE EXPLODED VIEW ON THIS PAGE HAVE  
BEEN INCLUDED BEFORE BEGINNING THIS INSTALLATION.  
CAUTION: USE CAUTION WHEN HANDLING PARTS,  
AS THEY MAY CONTAIN SHARP EDGES.  
WORK GLOVES ARE RECOMMENDED TO PREVENT INJURY.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IN-GROUND POST INSTALLATION  
16  
The U48 and P48 In-Ground Posts are only for  
use with Broilmaster® Gas Grills. Before  
proceeding with installation read your Owners  
Manual for the proper location and minimum  
clearances to combustible materials for your grill  
and in-ground post.  
CAUTION: THE CONCRETE MIXTURE MUST NOT  
COVER THE GAS SUPPLY ENTRY HOLE ON THE POST.  
THE GAS SUPPLY ENTRY HOLE (2" DIAMETER HOLE)  
IS LOCATED 18 3/4" FROM THE BOTTOM OF THE  
POST.  
Make a final alignment check with the level, and  
adjust as needed. Allow concrete to set (usually  
24 hours).  
Verify that all parts listed in the exploded view of  
this product have been included before beginning  
this installation.  
Recommended Tools:  
2
Two adjustable wrenches or a socket set  
A medium Phillips screwdriver  
Pipe thread sealer or Teflon tape (for gas  
connections)  
After the concrete has set, insert the tubing (6) in  
the post. Figure 1.  
Note: Do not attempt to cut or alter the flex tube in  
any way.  
Soapy water solution (to test for leaks)  
1
FIGURE 1  
Dig a hole approximately 12" in diameter and 24"  
in depth at the desired grill location.  
Note: Normal Installationheight is achieved  
when the top of the in-ground post (7) is 25 1/4"  
above ground. This height provides a cooking  
surface height of 34 1/2" above ground when  
grids are placed in the high level position.  
8
6
25-1/4"  
7
Carefully lower the in-ground post into the hole  
using the following guidelines:  
GAS  
SUPPLY  
PIPING  
The rectangular cut-out is located near the  
TOP of the post and should be above ground  
after installation.  
SYSTEM  
The rectangular cut-out must face in the  
SAME direction as the front of the grill.  
Hole depth and post measurements should be  
checked to ensure desired height.  
Note: Make any adjustments at this time.  
Prepare concrete or a standard pre-mix  
according to the manufacturers package  
directions.  
Position the post in the center of the hole. A level  
should be used when aligning the post to achieve  
precise vertical alignment. Hold the post in place  
while pouring the concrete mixture into the hole  
around the post.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IN-GROUND POST INSTALLATION  
17  
3
5
Insert a bolt (5) through one of the four holes in  
the top of the post. Fasten an eyebolt (4), flat  
washer (1), lock washer (2), and nut (3) to the bolt  
(5) Inside the post. Repeat this process for the  
three remaining holes. Figure 2.  
Note: See grill Owners Manual for location of the  
grills gas valve.  
Arrange with the gas company to have a gas  
supply piping system installed and connected to  
the bottom end of the copper tubing (6). Figure 2.  
Note: See label on grill for gas pressure  
information. The gas supply piping system MUST  
have a shutoff valve. The valve must remain in  
the OFF position when the gas supply piping  
system is not in use.  
3
2
Gas leak tests should be completed as directed in  
the grill Owners Manual.  
4
Completely fill remaining hole with soil.  
GRILL  
BOTTOM  
FIGURE 2  
6
6
Attach the control housing using two #8 x 1/2  
screws (11) or two plastic panel fasteners as  
shown in Figure 4.  
4
Place the grill bottom on top of the post with the  
four eyebolts (4) protruding through the holes  
located on the grill bottom.  
FIGURE 4  
Secure the grill bottom to the post by placing a  
lock washer (2) and nut (3) onto each of the four  
eyebolts (4). Figure 3.  
8
9
FIGURE 3  
3
2
4
GRILL  
BOTTOM  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
IN-GROUND POST INSTALLATION  
7
18  
Assemble the grease cup bracket using a #10  
Wing Nut. Figure 5.  
FIGURE 5  
8
Use the factory installed screw to fasten the  
grease cup bracket to the bottom of the grill. Slide  
the bracket up or down to install. Figure 6.  
Use only noncombustible containers for the  
grease cup (aluminum or tin cans). DO NOT use  
combustible containers such as paper or  
Styrofoam cups.  
Complete grill assembly as directed in the grill  
Owners Manual.  
FIGURE 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
20  
LIMITED WARRANTY  
Manufactured by: BROILMASTER®, A Division of Empire Comfort Systems, Inc., 918 Freeburg Ave.,  
Belleville, Illinois 62220.  
WHAT IS COVERED AND FOR HOW LONG  
From the date this gas grill is first purchased for use, BROILMASTER® will make available, at our factory,  
a free replacement for any defective part in accordance with the following limitations:  
STAINLESS STEEL CART - Lifetime by original purchaser for as long as grill is, and safely can be used as a  
residential grill.  
STAINLESS STEEL MOUNTINGS - Lifetime, as long as grill is, and safely can be, used as a residential gas grill.  
PAINTED ELECTROGALVANIZED STEEL COMPONENTS - 5 years against perforation.  
ALL OTHER PARTS - 2 years from date of purchase.  
WHAT IS NOT COVERED  
Removal and reinstallation cost.  
Labor costs for replacement or repairs.  
Transportation or shipping cost.  
The cost of a service call to diagnose trouble.  
Finishes on surfaces.  
Damage caused by improper installation, improper storage, accident, misuse, abuse or alteration.  
Unsatisfactory performance due to improper or lack of cleaning.  
LIMITATIONS AND EXCLUSIONS  
1. No one has authority to add to or vary this limited warranty, or to create for BROILMASTER® any other  
obligation of liability in connection with this grill mounting.  
2. ANY IMPLIED WARRANTY APPLICABLE TO THIS GRILL MOUNTING IS LIMITED IN DURATION TO  
THE SAME PERIOD OF TIME AS THIS WRITTEN WARRANTY. Some states do not allow limitations  
on how long an implied warranty lasts, so the above limitations may not apply to you.  
3. BROILMASTER® SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, SPECIAL OR CONTINGENT DAMAGES  
YOU MIGHT SUFFER AS A RESULT OF ITS BREACH OF THIS WRITTEN WARRANTY OR ANY IMPLIED WARRANTY. Some  
states do not allow the exclusion of limitation of incidental or consequential damages, so the above  
limitations may not apply to you.  
4. This warranty applies only to the original purchaser and may not be transferred.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
21  
5. This warranty applies only to gas grill mountings sold and used in the United States or Canada.  
6. This warranty applies only to gas grill mountings.  
7. If you cannot verify the purchase date of the grill mounting the warranty period will begin on the date the  
grill mounting was manufactured.  
8. Replacement or repair parts are warranted for the remaining period of the original part warranty.  
YOUR DUTIES  
This grill mounting must be assembled, installed, operated and maintained in accordance with all applicable  
codes and the instruction manual furnished with the grill mounting. You must keep an invoice, canceled  
check or payment record to verify the purchase date of the grill mounting.  
IF YOU HAVE A PROBLEM WITH YOUR GRILL MOUNTING  
1. Contact your BROILMASTER® dealer. If you cannot locate your dealer, call or write  
BROILMASTER® Technical Service Department as indicated below.  
2. If you do not receive satisfactory service from the dealer within a reasonable time, write  
BROILMASTER® Technical Service Department and include the date you purchased your  
grill mounting, its model number, the name and address of the dealer from whom it was  
purchased, and a description of the problem you are having. Furnish a dated proof of  
purchase if your grill mounting is within its warranty period.  
TechnicalServiceDepartment  
BROILMASTER®  
A Division of Empire Comfort Systems, Inc.  
918 Freeburg Ave.  
Belleville, IL 62220  
Phone: 800-851-3153 Fax: 618-233-7097  
This warranty gives you specific legal rights, and you may also  
have other rights which vary from state to state.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BROILMASTER®  
A DIVISION OF EMPIRE COMFORT SYSTEMS, INC.  
918 FREEBURG AVE.  
BELLEVILLE, ILLINOIS 62220  
PHONE: 618-233-7450 FAX: 618-233-7097  
1-800-851-3153  
VISIT OUR WEB SITE AT WWW.broilmaster.com  
RETAIN OWNERS MANUAL FOR FUTURE REFERENCE.  
FORM NO. 076814-0-0900  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Belkin Computer Hardware F5U502 User Manual
BenQ Thermometer sp870 User Manual
BMW Automobile Parts 733i User Manual
Braun Blender M 810 Duo, M 820 Trio, M 830 Trio, M 870 Quattro, M 880 Quattro User Manual
Briggs Stratton Pressure Washer 020330 0 User Manual
Broan Ventilation Hood 433004 User Manual
Califone Video Game Controller MCFEW1 D User Manual
Cambridge Audio CD Player 740C User Manual
Canon Printer 8746B002 User Manual
Carrier Air Conditioner 40KMC 301 User Manual