Brocade VA-40FC QuickStart Guide
5. Click Next. The Connect Cables screen is displayed.
Complete the steps in this guide to install and setup your Brocade VA-40FC switch using EZSwitchSetup. Refer to the Brocade
VA-40FC Hardware Reference Manual and the Fabric OS Administrator’s Guide (located on the Brocade VA-40FC
Documentation CD) if you want to choose a different set up.
3
ATTENTION
Power up and connect cables to the switch
The Brocade VA-40FC comes pre-configured in Access Gateway mode with the default F_Port-to-N_Port mappings (shown in Step
5 of this guide). You do not need to configure Access Gateway if you use the default F_Port-to-N_Port mappings. You can change
the default configuration using command line interface (CLI) or WebTools, after launching EZSwitchSetup as described below to
configure an IP address that is reachable on your network.
The Connect Cables screen shows you the connections you need to make.
1.Connect the power cord to the switch and then to the
power source (1). The power and status LEDs display
amber then green. This can take from one to 3 minutes.
Access Gateway mode can only be enabled or disabled when the VA-FC40 is in a disabled state. To deploy the Brocade VA-40FC
as a traditional fabric switch with all fabric services enabled but without Access Gateway functionality, enter the switchDisable
and then ag --modeDisable commands or perform the equivalent operations in WebTools. To deploy the switch in Access Gateway
mode, enter the switchDisable command on the VA-40FC and enter the ag –modeEnable command or its WebTools equivalent.
These operations are data disruptive and trigger an automatic reboot of the VA-40FC before it comes up in the new mode.
2.Connect the switch and the set up computer to the
same LAN, using Ethernet cables (3, 5) and an Ethernet
hub or switch (2). Be sure the Ethernet hub or switch is
connected to a power source (6).
3.If you want to use a serial connection for setup,
connect your set up computer COM port (7) to the serial
port on the switch, using the serial cable shipped with
the switch (4). The serial connections settings are as
follows:
1
Getting Ready
Before you start the installation and setup of your switch, ensure the following items are available.
•Bits per second: 9600
•Databits: 8
•Parity: none
•Stop bits: 1
•Flow control: none
Fixed IP address (IPv4 or IPv6) for the switch (no DHCP server): _________________________________________________________________
Subnet mask value: ___________________________________________________________________________________________________
Default Gateway value: ________________________________________________________________________________________________
Brocade switch World Wide Name (WWN) located on the switch ID pullout: ________________________________________________________
Ethernet connection (hub or switch)
EZSwitchSetup CD
Browser that allows pop-up windows
Ethernet and Fibre Channel cables
Set up computer
Optical transceivers (SFPs)
4. Click Next.
•
If you chose the Ethernet connection, the Discover Switch screen is displayed. Enter the switch WWN, following the
instructions on the Discover Switch screen. After completing switch discovery, the Set Switch IP Address screen is
displayed.
•
If you chose to use the serial port connection, the Set Switch IP Address screen is immediately displayed.
2
Installing and starting EZSwitchSetup
4
1. Insert the EZSwitchSetup CD into the CD-ROM drive of your set up computer. The installer will autostart in about a minute.
2. Follow the EZSwitchSetup directions for installation. Installation will take a few minutes after you click OK.
3. Wait for EZSwitchSetup to start, which should happen automatically after it is installed.
Setting the switch IP address
1. Enter the required information on the Set Switch IP Address screen.
2. Click Next.
For Windows and Linux instructions, refer to the EZSwitchSetup Administrator’s Guide.
The Confirm IP Address screen is displayed.
3. Click Next to confirm the addresses.
4. On the EZSwitchSetup Introduction screen, choose the option that matches your set up configuration:
•
•
Ethernet connection. This option uses the Ethernet LAN connection used for running EZSwitchSetup Manager.
Direct connection to the switch with a serial cable.
Download from Www.Somanuals.com. All Manuals Search And Download.
|