Brinkmann Smoker 140 7085 K User Manual

7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 2  
OWNER’S MANUAL / MANUAL DEL PROPIETARIO  
ASSEMBLY AND OPERATING INSTRUCTIONS  
INSTRUCCIONES DE ARMADO Y OPERACIÓN  
SAVE THIS MANUAL FOR FUTURE REFERENCE  
GUARDE ESTE MANUAL PARA REFERENCIA FUTURA  
WARNING/ADVERTENCIA  
HAZARDOUS EXPLOSION MAY RESULT IF THESE WARNINGS AND INSTRUCTIONS  
ARE IGNORED. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS IN THIS  
MANUAL TO AVOID PERSONAL INJURY, INCLUDING DEATH OR PROPERTY DAMAGE.  
SE PUEDE PRODUCIR UNA EXPLOSIÓN PELIGROSA SI SE HACE CASO OMISO A  
ESTAS ADVERTENCIAS E INSTRUCCIONES. LEA Y SIGA TODAS LAS ADVERTENCIAS  
E INSTRUCCIONES EN ESTE MANUAL PARA EVITAR LESIONES PERSONALES,  
INCLUSO LA MUERTE, O LOS DAÑOS MATERIALES.  
NOTICE TO INSTALLER:  
LEAVE THESE INSTRUCTIONS  
WITH THE GRILL OWNER FOR  
FUTURE REFERENCE.  
AVISO PARA EL  
INSTALADOR:  
ENTREGUE ESTAS  
INSTRUCCIONES AL PROPIETARIO  
DE LA PARRILLA PARA  
REFERENCIA FUTURA.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 4  
WARNING  
Use caution when reaching into or under smoker. Always wear oven mitts/gloves to protect your hands from burns. Avoid  
touching hot surfaces.  
Base pan should never be touched or moved while smoker is in operation or if still hot.  
The side door is for viewing purposes and adding water to water pan ONLY. Never add wood or any other material through the  
side door. When opening door, stand back and use caution to avoid burns from steam, flame flare-ups or splashes from hot  
water.  
Do not wear loose clothing or allow hair to hang freely when operating smoker.  
Always wear shoes when operating smoker.  
When in operation, smoker contains hot liquid in water pan. Extreme caution should be used at all times. Do not move smoker  
when water pan contains hot liquids. Tilting or other slight movement could cause hot liquid to spill from water pan causing  
serious bodily injury.  
When lifting the dome lid, keep hands, face and body safe from hot steam or possible flame flare-ups. Always lift the dome lid  
off the smoker by tilting the dome lid toward you to allow hot steam to escape away from your face. Should a flame flare-up  
occur, replace dome lid and unplug smoker to smother flame. Do not use water to extinguish flames.  
Use extreme caution when adding liquid to water pan being careful not to spill any liquid onto electric element. Always unplug  
smoker before adding water. Follow instructions in “Adding Water During Cooking" section of this manual.  
Water pan should always be used when smoking. Do not allow liquid in water pan to completely evaporate. Check water pan  
every 2 hours and add water if level is low (a sizzling sound may indicate a need for water). Follow instructions in “Adding  
Water During Cooking” section of this manual.  
Use a sufficient amount of flavoring wood to avoid having to remove smoker body from base pan during the cooking process.  
This will limit the danger of spilling hot liquid from the water pan which could cause serious bodily injury.  
Use caution when assembling or operating your smoker to avoid cuts or scrapes from sharp edges of metal parts.  
Never add charcoal, lighter fluid, fuel or material of any kind, other than flavoring wood to the base pan where the electric  
element and lava rocks are housed. Place wood chunks on lava rocks away from the electric element.  
Unplug the smoker from electric outlet when not in use. Allow smoker to cool completely before cleaning. Make sure embers  
are completely extinguished. Dispose of remaining embers and ashes in a noncombustible container. Do not allow ashes to  
build up in smoker.  
Do not use the smoker if the electric element has been exposed to moisture, grease and drippings, or if there is excessive ash  
buildup on the lava rock. Do not clean electric element with a water spray or the like. Failure to adhere to this safety warning  
could result in the electric element shorting out and in some cases, exploding. Clean the Electric element and lava rocks as  
instructed in the “Proper Care and Maintenance” section of this manual.  
Store the smoker indoors in a dry location when not in use–out of the reach of children.  
Accessory attachments not manufactured by The Brinkmann Corporation for this smoker are not recommended and may lead to  
personal injury or property damage.  
Use caution when lifting or moving smoker to prevent strains and back injuries.  
We advise that you have a fire extinguisher designed for use with electrical appliances on hand. Refer to your local authority to  
determine proper size and type of fire extinguisher.  
Do not attempt to service smoker other than normal maintenance as explained in “After-Use Safety and Proper Care &  
Maintenance” sections of this manual. Repairs should be performed by The Brinkmann Corporation only.  
Properly dispose of all packaging material.  
USE CAUTION AND COMMON SENSE WHEN OPERATING YOUR SMOKER.  
FAILURE TO ADHERE TO SAFETY WARNING AND GUIDELINES IN THIS MANUAL COULD RESULT  
IN BODILY INJURY OR PROPERTY DAMAGE.  
SAVE THESE INSTRUCTIONS  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 5  
ASSEMBLY INSTRUCTIONS  
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY  
BEFORE ASSEMBLING OR OPERATING YOUR SMOKER.  
FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 800-527-0717.  
(Proof of purchase will be required.)  
11  
10  
Inspect contents of the box to ensure all parts  
are included and undamaged.  
Tools required to assemble your  
Gourmet Electric Smoker and Grill:  
1
Flathead Screwdriver  
Pliers  
PARTS LIST:  
3
1
2
3
4
5
6
7
8
9
1
1
2
1
1
1
1
1
1
3
6
3
3
1
Dome Lid  
4
Smoker Body  
11  
152" Chrome Cooking Grills  
Porcelain Water Pan  
Base Pan  
12  
11  
9
Lava Rock Pan  
13  
Electric Element  
10  
Door with Latch  
Door Hinge  
10  
11  
12  
13  
14  
Metal Brackets for Handles  
Wooden Handle Halves  
Upper Support Brackets (Single Clip)  
Lower Support Brackets (V Clip)  
Bag Lava Rocks  
2
8
7
12 10-24 x s" Screws and Square Nuts  
6
6
6-32 x 4" Screws and Nuts (for Door)  
8-32 x w" Screws and Nuts (for Handles)  
Wood Chunk (sample)  
6
5
14  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 6  
STEP 1  
a. Attach wooden handle halves to metal brackets using 8-32 x w"  
screws and nuts as illustrated.  
b. Attach two handle assemblies to side of smoker body using  
10-24 x s" screws and square nuts as illustrated.  
c. Attach the three lower support brackets (V-clips) to inside of smoker  
body through the three 4" holes that are located about halfway down  
the smoker body (lower level). Mount each bracket with notched side  
facing up using 10-24 x s" screws and square nuts. Tighten screws  
securely.  
d. Attach the three upper support brackets (single clips) to inside of  
smoker body through the three 4" holes located near the top edge.  
Mount each bracket with notched side facing up using 10-24 x s"  
screws and square nuts. Tighten screws securely.  
Lower support bracket  
(V-clip) with notched  
side facing up.  
Upper support bracket  
with notched side  
facing up.  
STEP 2  
a. Attach hinge to inside of smoker body as illustrated. Use  
6-32 x 4" screws and nuts to attach hinge to smoker body.  
NOTE: Attach the hinge so pin is facing out of smoker as illustrated.  
b. Attach door to hinge using the remaining 6-32 x 4" screws and nuts.  
Pin Facing Out  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 7  
STEP 3  
a. Place lava rock pan inside base pan and align the hole in the side of  
each pan.  
b. Working from the inside of the lava rock pan, feed the cord of the  
electric element through the aligned holes until the back plate of the  
electric element is resting against the wall of the lava rock pan. Empty  
the entire bag of lava rocks into the pan and spread evenly.  
c. Lift the electric element up and position it on top of lava rocks. Keep the  
back plate of the electric element flush against wall of lava rock pan.  
STEP 4  
a. Place water pan inside smoker body on top of lower support brackets.  
Position water pan so the rim is resting securely on notched out step of  
all three support brackets. Place smoker body on base pan.  
b. Place a cooking grill on the lower support brackets directly above  
water pan.  
c. Place a cooking grill on the upper support brackets so the outer rim is  
resting securely on notched out step of all three support brackets.  
STEP 5  
a. Attach the handle assembly on top of dome lid using 10-24 x s"  
screws and square nuts.  
b. Place dome lid on upper support brackets of smoker body.  
NOTE: The dome lid is not designed to fit snugly in the smoker body.  
The gap between dome lid and smoker body allows  
proper air draft.  
YOUR GOURMET ELECTRIC SMOKER IS NOW COMPLETELY ASSEMBLED.  
Before first use and after cleaning, apply a light coat of vegetable oil or  
vegetable cooking spray to the interior surface of the dome lid, smoker  
body, cooking grills and water pan. This simple process will help reduce  
interior rusting. DO NOT apply oil to the base pan or electric element.  
READ ALL SAFETY WARNINGS AND OPERATING INSTRUCTIONS  
PRIOR TO USING YOUR SMOKER.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 8  
OPERATING INSTRUCTIONS  
PLACE THE SMOKER OUTDOORS ON A HARD, LEVEL, NON-COMBUSTIBLE SURFACE  
AWAY FROM ROOF OVERHANG OR ANY COMBUSTIBLE MATERIAL. NEVER USE ON WOODEN OR OTHER SURFACES THAT  
COULD BURN. PLACE THE SMOKER AWAY FROM OPEN WINDOWS OR DOORS TO PREVENT SMOKE FROM ENTERING YOUR  
HOUSE. IN WINDY WEATHER, PLACE THE SMOKER IN AN OUTDOOR AREA THAT IS PROTECTED FROM THE WIND.  
READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY  
BEFORE OPERATING YOUR SMOKER.  
Prior to first use, cure your smoker to minimize damage to the exterior  
Curing Your Smoker  
finish as well as rid the smoker of paint odor that can impart unnatural  
flavors to the first meal prepared. Cure your smoker periodically  
throughout the year to protect against rust.  
1. Remove water pan from smoker and leave out during curing process.  
Lightly coat all interior surfaces of the smoker, dome lid and cooking  
grill’s with vegetable oil or vegetable oil spray. Do not coat lava rock  
pan, lava rock or electric element.  
NOTE:  
Do not use flavoring wood while curing your smoker.  
2. With the dome lid on smoker, plug the smoker into electric outlet.  
WARNING: Always use a 3-wire grounded outlet wired for 120-volts  
which is GFCI protected at 15 or 20 amps. If in doubt, contact  
a qualified electrician. Do not operate this smoker with any  
other appliance or electrical device on the same circuit.  
BRINKMANN  
DALLAS,TX 75244  
3. Cure smoker for three hours, then unplug smoker from electric outlet.  
Allow smoker to cool completely. It is important that the exterior of the  
smoker is not scraped or rubbed during the curing and cooling  
process.  
IMPORTANT: To protect your smoker from excessive rust, the unit must  
be cured periodically and covered at all times when not in  
use. A smoker cover may be ordered directly from  
Brinkmann by calling 1-800-468-5252.  
FOLLOW THESE STEPS BEFORE PLUGGING SMOKER INTO ELECTRIC OUTLET.  
1. remove dome lid and smoker body from base pan.  
1" (2.5 cm)  
2. Place flavoring wood on lava rock near the electric element. Refer to  
“Flavoring Wood” section for recommended amount of flavoring wood  
to use.  
NOTE: Do not place the flavoring wood directly on the electric element.  
This could cause flame flare-up and failure of the electric  
element.  
3. Place empty water pan inside smoker body on the lower support  
brackets. Position water pan so rim is resting securely on notched out  
step of all three support brackets.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 9  
CAUTION: Before each use, check handles and support brackets to make  
sure they are securely fastened.  
4. Place the smoker body on base pan, making sure the water pan is  
still in place.  
5. Carefully, fill water pan with warm water or marinade to 1" below the  
rim. A full pan holds 4 quarts of water and will last for approximately  
2-3 hours. Do not overfill or allow water to overflow from water pan.  
WARNING: Do not spill water or liquid onto electric element.  
6. Place a cooking grill on the lower support brackets directly above the  
water pan.  
7. Place food on the cooking grill in a single layer with space between  
each piece. This will allow smoke and moist heat to circulate evenly  
around all pieces.  
8. Place the other cooking grill on the upper support brackets. Make sure  
the rim is resting securely on notched out step of all three support  
brackets. Place food on the cooking grill.  
9. With the dome lid on smoker, plug the smoker into electric outlet.  
WARNING: Always use a 3-wire grounded outlet wired for 120-volts  
which is GFCI protected at 15 or 20 amps. If in doubt, contact  
a qualified electrician. Do not operate this smoker with any  
other appliance or electrical device on the same circuit.  
10. Allow food to cook. After 2-3 hours of cooking, check water level and  
add water if level is low. Follow instructions in the “Adding Water  
During Cooking” section of this manual.  
11. Always use a meat thermometer to ensure food is fully cooked before  
removing from smoker.  
20  
0
180  
POULTRY  
LAMB  
85  
80  
1
6
0
BEEF WELL  
PORK  
VEAL  
77  
140  
12. After cooking, always unplug the smoker from electric outlet. Allow  
smoker to cool completely, then follow instructions in the “After-Use  
Safety and Proper Care & Maintenance” sections of this manual.  
HAM  
BEEF  
MED. 70  
0
2
1
BEEF RARE  
HAM 60  
COOKED  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 10  
1. Remove dome lid and smoker body from base pan.  
Grilling  
2. Place a cooking grill on the base pan.  
3. Place food on the cooking grill in a single layer with space between  
each piece.  
4. Place dome lid on base pan and plug the grill into electric outlet.  
For best results, the dome lid should be placed on base pan when  
grilling food.  
WARNING: Always use a 3-wire grounded outlet wired for 120 volts  
which is GFCI protected at 15 or 20 amps. If in doubt, contact  
a qualified electrician. Do not operate this grill with any other  
appliance or electrical device on the same circuit.  
5. Always use a meat thermometer to ensure food is fully cooked before  
removing from smoker.  
WARNING: When grilling, drippings from meat may cause flame flare-up.  
Use extreme caution when removing the dome lid. Lift dome  
lid by tilting it toward you to allow heat and flame to escape  
away from your face. If flame flare-ups occur, replace the  
dome lid and unplug the grill to smother flame. Do not use  
water to extinguish a grease fire.  
6. After cooking, always unplug the grill from electric outlet. Allow grill to  
cool completely, then follow instructions in the “After-Use Safety and  
Proper Care & Maintenance” sections of this manual.  
To obtain your favorite smoke flavor, experiment by using chunks, sticks  
or chips of flavor producing wood such as hickory, pecan, apple, cherry,  
or mesquite. Most fruit or nut tree wood may be used for smoke  
flavoring. Do not use resinous woods such as pine as it will produce an  
unpleasant taste.  
Flavoring Wood  
Wood chunks or sticks 3" to 4" long and 2" to 1" thick work best. Unless  
the wood is still green, soak the wood in water for 20 minutes or wrap  
each piece in foil and tear several small holes in the foil to produce more  
smoke and prevent the wood from burning too quickly. A lot of wood is  
not required to obtain a good smoke flavor. A recommended amount is 3-  
4 wood chunks or sticks. Experiment by using more wood for stronger  
smoke flavor or less wood for milder smoke flavor.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 11  
Additional flavoring wood should not have to be added during the cooking  
process, however, it may be necessary when cooking very large pieces of  
meat. Follow the instructions and cautions below to avoid injury while  
adding wood.  
Adding Wood  
During Cooking  
1. Unplug smoker from electric outlet. Remove dome lid by tilting the  
dome lid toward you to allow heat and steam to escape away from your  
face. Use caution since flames can flare-up when fresh air suddenly  
comes in contact with grease fire.  
2. Wearing oven mitts, remove food from cooking grills, then smoker body  
from base pan.  
WARNING: The water in water pan will be extremely HOT. When lifting  
smoker body from base pan, use extreme caution and make  
sure the water pan is securely in place on the three lower  
support brackets. Keep legs and feet out from under the  
smoker body to avoid being scalded by hot liquids spilling  
from water pan. Be extremely careful not to tilt or jar smoker  
so hot water does not spill out of water pan.  
3. Set the smoker body with the water pan aside on a hard, level,  
noncombustible surface.  
4. Stand back a safe distance and use long cooking tongs to place  
flavoring wood on the lava rock. Do not allow flavoring wood to come in  
contact with the electric element.  
5. Replace smoker body with the water pan on base pan.  
WARNING: The water in water pan will be extremely HOT. When lifting  
smoker body from ground, use extreme caution and make  
sure the water pan is securely in place on the three lower  
support brackets. Keep legs and feet out from under the  
smoker body to avoid being scalded by hot liquids spilling  
from water pan. Be extremely careful not to tilt or jar smoker  
so hot water does not spill out of water pan.  
6. Replace food on cooking grills then place the dome lid on smoker body.  
7. Plug the smoker back into electric outlet and allow food to  
continue cooking.  
Check the water level in water pan if the complete cooking process takes  
longer than 2 hours. A low water level can be detected by listening for the  
sound of water sizzling. Water can be added to the water pan through the  
top of smoker or side door. Use caution and follow instructions carefully.  
Adding Water  
During Cooking  
WARNING: Do not spill water onto the electric element.  
OPTION 1: Adding Water Through Top of Smoker  
1. Unplug the smoker from electric outlet.  
2. Lift the dome lid off the smoker body by tilting the dome lid toward  
you to allow heat and steam to escape away from your face. Use  
caution since flames can flare-up when fresh air suddenly comes in  
contact with fire. Inspect the water level in pan.  
3. If water level is low, add water to water pan. If food is on top cooking  
grill only, water may be added to the water pan by moving food aside  
on cooking grill and pouring water down through the cooking grill. Fill  
water pan to 1" below the rim. Pour slowly to avoid splashing or  
overfilling.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 12  
If using both cooking grills, wear oven mitts to remove food and the top  
cooking grill. Move food aside on the lower cooking grill and pour water  
into water pan through the lower cooking grill. Pour slowly to avoid  
splashing or overfilling.  
1" (2.5 cm)  
4. Set the top cooking grill on the upper support brackets and place food  
back on the cooking grill.  
5. Place the dome lid on smoker body. Plug smoker back into electric  
outlet and allow food to continue cooking.  
OPTION 2: Adding Water Through the Side Door  
1. Unplug the smoker from electric outlet.  
2. Stand back and carefully open side door. Use caution since flames can  
flare-up when fresh air suddenly comes in contact with fire. Inspect the  
water level in pan.  
3. If water level is low, add water to water pan. Stand back and carefully  
add water using a funnel or a container with a spout. Fill water pan to 1"  
below the rim. Pour slowly to avoid splashing or overfilling.  
4. Close side door and plug smoker back into electric outlet. Allow food to  
continue cooking.  
Variation in flavor can be achieved by adding wine, soft drinks, herbs,  
spices, bits of citrus peel, fruit juice, onion or marinades to the water  
pan.  
Cooking Tips  
Brush poultry and naturally lean meats with cooking oil, butter or  
margarine before cooking.  
Meat should be completely thawed before cooking.  
When cooking more than one piece of meat, the cooking time is  
determined by the largest single piece being cooked.  
The meat bastes itself while cooking in the smoker. No basting or  
turning is necessary after the meat is placed on the grill. For added  
variety, barbecue sauce or marinade may be applied on meat before  
placing on grill.  
There is very little difference in temperature and cooking time between  
top and bottom grill levels. When cooking different types or cuts of meat  
at the same time, place the meat that requires the least cooking time on  
the top cooking grill so that it may be easily removed first. If only one  
cooking grill is required, use the upper grill level for best results.  
During the smoking process, avoid the temptation to lift dome lid to  
check food. Lifting the dome lid allows heat to escape, making additional  
cooking time necessary.  
Always use a meat thermometer to determine the proper degree of  
doneness. Many variables (outdoor temperature, the number of times  
the dome lid is removed, proximity of food to heat source, etc.) will  
affect actual cooking times. When using a meat thermometer, place  
probe midway into the thickest part of the meat, making sure that it does  
not touch any fat or bone. Allow five minutes for the thermometer to  
register temperature properly.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 13  
AFTER-USE SAFETY  
WARNING  
There is no ON/OFF control switch. Always turn the smoker “OFF” by unplugging cord from electric outlet when adding water  
and wood, or when finished cooking.  
Always allow the smoker and all components to cool completely before handling.  
Before smoker can be left unattended, remaining embers and ashes must be removed. Use caution to protect yourself and your  
property. Place remaining embers and ashes in a noncombustible metal container and completely saturate with water. Allow  
ashes and water to remain in metal container for 24 hours prior to disposing.  
Extinguished embers and ashes should be placed a safe distance from all structures and combustible materials.  
Cover and store the smoker indoors in a dry location, out of the reach of children.  
Wash water pan and cooking grills with hot, soapy water, rinse well  
Proper Care  
and dry. Lightly coat water pan and cooking grills with vegetable oil  
or vegetable cooking spray.  
& Maintenance  
Clean inside and outside of smoker by wiping off with a damp cloth.  
Apply a light coat of vegetable oil or vegetable cooking spray  
to the interior surfaces of the dome lid and smoker body to  
prevent rusting.  
After the electric element has completely cooled, clean with a damp  
cloth after each use. Allow electric element to air dry outside of base  
pan so that all moisture evaporates completely before storing.  
Clean lava rocks and lava rock pan periodically with baking soda  
and water solution. Rinse well and allow to air dry thoroughly  
before storing.  
If rust appears on the exterior surface of your cooker, clean and buff  
the affected area with steel wool or fine grit emery cloth. Touch-up  
with a good high-temperature resistant paint.  
Never apply paint to the interior surface. Rust spots on the interior  
surface can be buffed, cleaned, then lightly coated with vegetable oil  
or vegetable cooking spray to minimize rusting.  
Always keep your smoker covered when not in use to protect against  
excessive rusting. The Smoke’N Grill cover may be ordered directly  
from Brinkmann by calling 800-468-5252.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 14  
MEDIDAS DE PRECAUCIÓN IMPORTANTES  
DESEAMOS QUE USTED ENSAMBLE Y USE SU AHUMADOR DE LA MANERA MÁS SEGURA POSIBLE.  
EL PROPÓSITO DE ESTE SÍMBOLO DE ALERTA DE SEGURIDAD ES LLAMAR SU ATENCIÓN A POSIBLES PELIGROS  
MIENTRAS ENSAMBLA Y USA SU AHUMADOR. ¡CUÁNDO VEA EL SÍMBOLO DE ALERTA DE SEGURIDAD, PRESTE ATENCIÓN  
A LA INFORMACIÓN QUE APARECE DESPUÉS!  
LEA TODAS LAS ADVERTENCIAS DE SEGURIDAD E INSTRUCCIONES CUIDADOSAMENTE  
ANTES DE ENSAMBLAR Y UTILIZAR SU AHUMADOR.  
ADVERTENCIA  
Este ahumador debe ser usado únicamente en exteriores. No lo utilice en interiores ni en áreas cerradas.  
No use este ahumador bajo la lluvia ni en superficies mojadas. No sumerja el cable, enchufe o elemento eléctrico en agua u otros  
líquidos. Mantenga este ahumador y todos los aparatos eléctricos lejos de piscinas, bañeras de hidromasaje, etc. Hay peligro de  
descarga eléctrica si se usa en una superficie mojada, bajo la lluvia o si el aparato ha sido expuesto a la humedad.  
Para uso en el hogar únicamente. No use este producto para propósitos distintos a los indicados.  
Para evitar descargas eléctricas accidentales, siempre debe de conectar este ahumador a un enchufe o interruptor de circuito de  
falla conectado a tierra (GFCI, por sus siglas en inglés).  
Use siempre un tomacorriente de 3 cables con conexión a tierra cableado para 120 voltios que esté protegido por un interruptor de  
circuito de falla conectado a tierra (GFCI, por sus siglas en inglés) a 15 ó 20 amperios. En caso de duda, contacte a un electricista  
calificado. No opere este ahumador con otro electrodoméstico o aparato eléctrico en el mismo circuito.  
El ahumador se “enciende” al conectarlo a un tomacorriente. No hay interruptor de ENCENDIDO/APAGADO. Antes de conectar la  
unidad al tomacorriente, el ahumador debe estar totalmente preparado con la madera saborizante en su lugar, el líquido en la  
bandeja para agua, la carne en las rejillas y la tapa de domo sobre el ahumador. Apague siempre la unidad desconectándola del  
tomacorriente cuando agregue agua o termine de cocinar.  
No use un cable de extensión a menos que sea absolutamente necesario. Si tiene que usar uno, debiera ejercitar ciertos cuidados:  
a. Que sea lo más corto posible. Use un cable de extensión con conexión a tierra de 12/3 ó 14/3 con una clasificación de  
por lo menos 15 amperios.  
b. El cable debiera estar marcado con el sufijo “W-A” y una etiqueta que diga “apropiado para usar con electrodomésticos  
para exteriores”.  
c. Mantenga la conexión del cable de extensión seca y elevada. El aparato y/o el cable de extensión debieran estar puestos  
de tal manera que nadie se tropiece con ellos, ni los puedan tironear niños o mascotas. No permita que el cable toque las  
superficies calientes.  
No utilice este ahumador si:  
a. El cable o enchufe están dañados.  
b. El elemento eléctrico ha sido dañado de cualquier manera.  
c. El ahumador ha fallado.  
d. El ahumador ha sido expuesto a la humedad o si la grasa y el goteo no han sido limpiados del elemento después de cada  
uso. Refiérase a la sección de “Mantenimiento y cuidado adecuados” de este manual.  
e. Si el ahumador tiene cualquier daño. (Devuelva el ahumador tras la previa obtención del Número de Autorización de  
Devolución a The Brinkmann Corporation para su examen, reparación o reemplazo.)  
f. Si el interruptor de circuito de falla conectado a tierra (GFCI, por sus siglas en inglés) se activa cuando el elemento  
eléctrico es conectado al tomacorriente.  
Una distancia apropiada de 5 pies entre el ahumador y cualquier construcción inflamable debiera mantenerse todo el tiempo  
cuando el producto está en uso.  
En clima ventoso, este producto debería ser colocado en un área de exteriores que esté protegida del viento.  
No deje desatendido el ahumador mientras lo utiliza.  
No coloque el ahumador sobre o cerca de un quemador de gas o eléctrico, ni de un horno caliente.  
No almacene ni utilice el ahumador cerca de gasolina u otros líquidos inflamables, gases ni donde pudiera haber vapores  
inflamables.  
Use este ahumador únicamente en una superficie dura, nivelada, no inflamable y estable (concreto, tierra, etc.). Nunca lo use sobre  
superficies de madera ni sobre otras que pudieran quemarse.  
Una bandeja recogegotas/guarda cenizas no evitará que ocurra un incendio en madera u otra superficie inflamable. Una bandeja  
recogegotas/guarda cenizas está diseñada para ser utilizada con un ahumador para una fácil limpieza de los goteos que pueden  
causar decoloración de la superficie y para atrapar cenizas y brasas.  
El ahumador debiera ser colocado en un área en la que niños y mascotas no puedan entrar en contacto con la unidad. Es necesaria  
una atenta supervisión mientras este ahumador está en uso.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 15  
ADVERTENCIA  
Tenga precaución cuando alcance cosas dentro o debajo del ahumador. Use siempre mitones o guantes resistentes al calor para  
proteger sus manos de quemaduras. Evite tocar superficies calientes.  
La bandeja de base nunca debe ser tocada o movida mientras el ahumador está funcionando o si aún está caliente.  
La puerta lateral es ÚNICAMENTE para observar el contenido y para agregar agua a la bandeja para agua. Nunca agregue madera ni  
cualquier otro material a través de la puerta lateral. Cuando abra la puerta, aléjese y tenga precaución para evitar quemaduras por  
el vapor, llamaradas o salpicaduras de agua caliente.  
No vista ropa floja ni use el cabello suelto cuando use el ahumador.  
Use siempre zapatos cuando utilice el ahumador.  
Cuando está funcionando, el ahumador contiene líquido caliente en la bandeja para agua. Debe tomar medidas de precaución  
extremas todo el tiempo. No mueva el ahumador cuando la bandeja para agua contenga líquidos calientes. Ligeros movimientos o  
inclinaciones podrían causar que el líquido caliente se derrame de la bandeja para agua provocando serias lesiones corporales.  
Cuando levante la tapa de domo, mantenga sus manos, cara y cuerpo seguros del vapor caliente o de posibles llamaradas.  
Siempre levante la tapa de domo del ahumador inclinándola hacia usted para permitir que el vapor caliente escape en la dirección  
opuesta a la suya. Si ocurriera una llamarada, vuelva a poner la tapa de domo en su lugar y desconecte el ahumador para sofocar  
la llama. No use agua para extinguir las llamas.  
Sea extremadamente precavido cuando agregue líquidos a la bandeja para agua, teniendo cuidado de no derramar ningún líquido  
sobre el elemento eléctrico. Siempre desconecte el ahumador antes de agregar agua. Siga las instrucciones contenidas en la  
sección de “Para agregar agua mientras cocina” de este manual.  
La bandeja para agua siempre debe ser utilizada mientras ahuma. No permita que el líquido en la bandeja para agua se evapore  
totalmente. Revise la bandeja para agua cada dos horas y agregue agua si su nivel es bajo (un sonido siseante podría indicar que  
se necesita más agua). Siga las instrucciones que aparecen en la sección de “Para agregar agua mientras cocina” de este manual.  
Use una cantidad suficiente de madera saborizante para evitar tener que quitar la unidad principal del ahumador de la bandeja de  
base durante el proceso de cocción. Esto limitará el peligro de derramar líquidos calientes de la bandeja para agua, lo que podría  
causar serias lesiones corporales.  
Tenga precaución cuando ensamble o utilice su ahumador para evitar raspones o cortaduras causados por las esquinas filosas de  
las partes de metal.  
Nunca agregue carbón, líquido encendedor, combustible ni materiales de cualquier tipo que no sean madera saborizante, a la  
bandeja de base donde se encuentran alojados el elemento eléctrico y las piedras volcánicas. Coloque los pedazos de madera  
sobre las piedras volcánicas alejados del elemento eléctrico.  
Desconecte el ahumador del tomacorriente cuando no lo esté usando. Permita que el ahumador se enfríe completamente antes de  
limpiarlo. Asegúrese que las brasas estén totalmente apagadas. Deseche las brasas y cenizas restantes dentro de un contenedor no  
inflamable. No permita que las cenizas se acumulen en el ahumador.  
No use el ahumador si el elemento eléctrico ha sido expuesto a humedad, grasa y goteos, o sí hay una cantidad excesiva de ceniza  
en las piedras volcánicas. No limpie el elemento eléctrico con un rociador de agua o algo similar. No adherirse a esta advertencia  
de seguridad podría tener por resultado que el elemento eléctrico haga corto circuito y, en algunos casos, hasta explote. Limpie el  
elemento eléctrico y las piedras volcánicas según lo indica la sección de “Mantenimiento y cuidado apropiados” de este manual.  
Cuando no lo esté usando, guarde el ahumador adentro en un lugar seco—fuera del alcance de los niños.  
El uso de accesorios no fabricados por The Brinkmann Corporation para este ahumador no se recomienda y podría resultar en  
lesiones personales o daños a la propiedad.  
Tenga precaución cuando levante o mueva el ahumador para prevenir estirones y lesiones a su espalda.  
Le recomendamos que tenga a mano un extinguidor diseñado para usarse en aparatos eléctricos. Refiérase a sus autoridades  
locales para determinar el tamaño y tipo apropiados de extinguidor.  
No intente dar otros servicios al ahumador distintos a los normales, según como se explica en la sección de “Seguridad para  
después del uso y Mantenimiento y cuidado adecuados” de este manual. Las reparaciones deben ser hechas únicamente por The  
Brinkmann Corporation.  
Deseche el material de empaque de la manera adecuada.  
TENGA PRECAUCIÓN Y HAGA USO DEL SENTIDO COMÚN CUANDO UTILICE SU AHUMADOR  
NO SEGUIR LAS ADVERTENCIAS DE SEGURIDAD Y LOS LINEAMIENTOS DE ESTE MANUAL PODRÍA RESULTAR EN  
LESIONES CORPORALES O DAÑOS A LA PROPIEDAD.  
GUARDE ESTAS INSTRUCCIONES  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 16  
INSTRUCCIONES DE ENSAMBLAJE  
LEA TODAS LAS ADVERTENCIAS DE SEGURIDAD E INSTRUCCIONES DE ENSAMBLAJE  
CUIDADOSAMENTE ANTES DE ENSAMBLAR U OPERAR SU AHUMADOR.  
PARA PIEZAS FALTANTES, POR FAVOR LLAME A SERVICIO AL CLIENTE AL 800-527-0717.  
(Se requerirá prueba de compra.)  
11  
10  
Inspeccione el contenido de la caja para asegurarse que todas  
las partes estén incluidas y sin daños.  
Herramientas requeridas para ensamblar su  
Ahumador y parrilla eléctrica Gourmet  
1
Destornillador plano  
Alicates  
LISTA DE PIEZAS:  
3
4
1
2
3
4
5
6
7
8
9
1
1
2
1
1
1
1
1
1
3
6
3
3
1
Tapa de domo  
Unidad principal del ahumador  
Rejillas para cocinar cromadas de 152" (39.37 cm)  
Bandeja para agua de porcelana  
Bandeja de base  
11  
12  
11  
9
Bandeja para piedras volcánicas  
Elemento eléctrico  
13  
10  
Puerta con pestillo  
Bisagra de puerta  
10  
11  
12  
13  
14  
Soportes de metal para las manijas  
Mitades de manijas de madera  
Soportes de apoyo superiores (una sola pinza)  
Soportes de apoyo inferiores (pinza en V)  
Bolsa de piedras volcánicas  
2
8
7
12 Tornillos y tuercas cuadradas de 10-24 x s"  
6
6
Tornillos y tuercas de 6-32 x 4" (para la puerta)  
Tornillos y tuercas de 8-32 x w" (para las manijas)  
Bloque de madera (muestra)  
6
5
14  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 17  
PASO 1  
a. Fije las mitades de la manija de madera a los soportes de metal  
utilizando tornillos y tuercas de 8-32 x w" como se ilustra.  
b. Fije dos conjuntos de manijas a los lados de la unidad principal del  
ahumador usando tornillos y tuercas cuadradas de 10-24 x s" como  
se ilustra.  
c. Fije los tres soportes de apoyo inferiores (pinza en V) a la parte interior  
de la unidad principal del ahumador a través de los 3 agujeros de 4"  
que se encuentran ubicados más o menos a la mitad de la unidad  
principal del ahumador (nivel inferior). Instale cada soporte con el lado  
muescado hacia arriba usando los tornillos y tuercas cuadradas de 10-  
24 x s". Apriete bien los tornillos.  
d. Fije los tres soportes de apoyo superiores (una sola pinza) a la parte  
interior de la unidad principal del ahumador a través de los agujeros de  
4" ubicados cerca del borde superior. Coloque cada soporte con el lado  
muescado hacia arriba usando tornillos y tuercas cuadradas de  
10-24 x s". Apriete bien los tornillos.  
Soporte de apoyo inferior (pinza en V)  
con el lado muescado hacia arriba.  
Soporte de apoyo superior con el lado  
muescado hacia arriba.  
PASO 2  
a. Fije la bisagra a la parte interior de la unidad principal del ahumador  
como se ilustra. Use tornillos y tuercas de 6-32 x 4" para fijar la  
bisagra a la unidad principal del ahumador.  
NOTA: Fije la bisagra para que la pinza de hacia afuera del ahumador  
como se ilustra.  
Pinza hacia afuera.  
b. Fije la bisagra a la puerta usando los tornillos y tuercas de 6-32 x 4"  
restantes.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 18  
PASO 3  
a. Coloque la bandeja para piedras volcánicas dentro de la bandeja de base y  
alinee el agujero en el lado de cada bandeja.  
b. Trabaje desde adentro de la bandeja para piedras volcánicas alimentando el  
cable del elemento eléctrico a través de los agujeros ya alineados hasta que  
la placa trasera del elemento eléctrico esté apoyada contra la bandeja para  
piedras volcánicas. Vacíe toda la bolsa de piedras volcánicas dentro de la  
bandeja y espárzalas de manera uniforme.  
c. Levante el elemento eléctrico hacía arriba y póngalo sobre las piedras  
volcánicas. Mantenga la placa trasera del elemento eléctrico al ras de la  
pared de la bandeja para piedras volcánicas.  
PASO 4  
a. Coloque la bandeja para agua dentro de la unidad principal del ahumador  
sobre los soportes de apoyo inferiores. Ponga la bandeja para agua de tal  
modo que el borde esté apoyado seguramente en la parte muescada de los  
tres soportes de apoyo. Coloque la unidad principal del ahumador sobre la  
bandeja de base.  
b. Coloque una rejilla para cocinar en los soportes de apoyo inferiores que  
están directamente sobre la bandeja para agua.  
c. Coloque una rejilla para cocinar en los soportes de apoyo superiores de  
modo que el borde esté apoyado seguramente en la parte muescada de los  
tres soportes de apoyo.  
PASO 5  
a. Fije el conjunto de manija sobre la tapa de domo usando tornillos y tuercas  
cuadradas de 10-24 x s".  
b. Coloque la tapa de domo sobre los soportes de apoyo superiores de la  
unidad principal del ahumador.  
NOTA: La tapa de domo no está diseñada para casar perfectamente en la  
unidad principal del ahumador. El espacio entre la tapa de domo y la  
unidad principal del ahumador permite una corriente de aire apropiada.  
SU AHUMADOR ELÉCTRICO GOURMET ESTÁ AHORA COMPLETAMENTE  
ENSAMBLADO.  
Antes del primer uso y después de limpiar, aplique una delgada capa de  
aceite vegetal o aerosol vegetal para cocinar a la superficie interior de la  
tapa de domo, la unidad principal del ahumador, las rejillas para cocinar y a  
la bandeja para agua. Este sencillo proceso ayudará a reducir la oxidación  
interna. NO aplique aceite a la bandeja de base ni al elemento eléctrico.  
LEA TODAS LAS ADVERTENCIAS DE SEGURIDAD E INSTRUCCIONES DE  
USO PREVIO A UTILIZAR SU AHUMADOR.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 19  
INSTRUCCIONES DE USO  
COLOQUE EL AHUMADOR EN EXTERIORES, EN UNA SUPERFICIE DURA, NIVELADA Y NO  
INFLAMABLE ALEJADA DE CUALQUIER ALERO DE TECHO O CUALQUIER OTRO MATERIAL INFLAMABLE. NUNCA USE EN SUPERFICIES DE  
MADERA U OTRAS QUE PUDIERAN QUEMARSE. COLOQUE EL AHUMADOR LEJOS DE VENTANAS ABIERTAS O PUERTAS PARA PREVENIR  
QUE EL HUMO ENTRE A SU CASA. EN CLIMA VENTOSO, COLOQUE EL AHUMADOR EN UN ÁREA DE EXTERIORES EN LA QUE ESTÉ  
PROTEGIDO DEL VIENTO.  
LEA TODAS LAS ADVERTENCIAS DE SEGURIDAD E INSTRUCCIONES CUIDADOSAMENTE ANTES  
DE UTILIZAR SU AHUMADOR.  
Prior to first use, cure your smoker to minimize damage to the exterior finish as  
Curing Your Smoker  
well as rid the smoker of paint odor that can impart unnatural flavors to the first  
meal prepared. Cure your smoker periodically throughout the year to protect  
against rust.  
1. Remove water pan from smoker and leave out during curing process. Lightly  
coat all interior surfaces of the smoker, dome lid and cooking grill’s with  
vegetable oil or vegetable oil spray. Do not coat lava rock pan, lava rock or  
electric element.  
NOTE:  
Do not use flavoring wood while curing your smoker.  
2. With the dome lid on smoker, plug the smoker into electric outlet.  
WARNING: Always use a 3-wire grounded outlet wired for 120-volts which is  
GFCI protected at 15 or 20 amps. If in doubt, contact a qualified  
electrician. Do not operate this smoker with any other appliance or  
electrical device on the same circuit.  
BRINKMANN  
DALLAS,TX 75244  
3. Cure smoker for three hours, then unplug smoker from electric outlet. Allow  
smoker to cool completely. It is important that the exterior of the smoker is  
not scraped or rubbed during the curing and cooling process.  
IMPORTANT: To protect your smoker from excessive rust, the unit must be  
cured periodically and covered at all times when not in use. A  
smoker cover may be ordered directly from Brinkmann by  
calling 1-800-468-5252.  
SIGA ESTOS PASOS ANTES DE CONECTAR SU AHUMADOR AL TOMACORRIENTE.  
Ahumar  
1. Quite la tapa de domo y la unidad principal del ahumador de la bandeja de  
base.  
1" (2.5 cm)  
2. Coloque madera saborizante sobre las piedras volcánicas cerca del elemento  
eléctrico. Refiérase a la sección de “Madera saborizante” de este manual para  
la cantidad recomendada de madera a usar.  
NOTA: No coloque madera saborizante directamente sobre el elemento  
eléctrico. Esto pudiera causar llamaradas y fallas en el elemento  
eléctrico.  
3. Coloque la bandeja para agua vacía dentro de la unidad principal del ahumador  
sobre los soportes de apoyo inferiores. Posicione la bandeja para agua de tal  
manera que esté apoyada seguramente sobre la parte muescada de los tres  
soportes de apoyo.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 20  
PRECAUCIÓN: Antes de cada uso, revise las manijas y soportes de apoyo para  
asegurarse de que estén bien sujetos.  
4. Coloque la unidad principal del ahumador sobre la bandeja de base,  
asegurándose de que la bandeja para agua siga en su lugar.  
5. Cuidadosamente, llene la bandeja para agua con agua tibia o marinada hasta  
1" (2.54 cm) por debajo del borde. Una bandeja llena contiene 1 galón de agua  
y durará aproximadamente 2-3 horas. No llene en exceso ni permita que el  
agua rebalse de la bandeja para agua.  
ADVERTENCIA: No derrame agua ni líquidos sobre el elemento eléctrico.  
6. No derrame agua ni líquidos sobre el elemento eléctrico.  
7. Coloque la comida en la rejilla para cocinar en una sola capa con espacio entre  
cada pieza. Esto permitirá que el humo y el calor de la humedad circulen  
uniformemente alrededor de todas las piezas.  
8. Coloque la otra rejilla para cocinar en los soportes de apoyo superiores.  
Asegúrese de que el borde esté apoyado seguramente en la parte muescada de  
los tres soportes de apoyo. Coloque la comida sobre la rejilla para cocinar.  
9. Con la tapa de domo sobre el ahumador, conecte el ahumador al  
tomacorriente.  
ADVERTENCIA: Use siempre un tomacorriente de 3 cables con conexión a tierra  
cableado para 120 voltios que esté protegido por un interruptor  
de circuito de falla conectado a tierra (GFCI, por sus siglas en  
inglés) a 15 ó 20 amperios. En caso de duda llame a un  
electricista calificado. No opere este ahumador con otro  
electrodoméstico o aparato eléctrico en el mismo circuito.  
10. Permita que la comida se cocine. Tras 2-3 horas de cocción, revise el nivel  
de agua y agregue agua si el nivel está bajo. Siga las instrucciones de la  
sección de “Para agregar agua mientras cocina” de este manual.  
2
0 0  
1 8 0  
11. Use siempre un termómetro de carne para asegurar que la comida está  
completamente cocida antes de retirarla del ahumador.  
P O U L T R Y  
L A M B  
8 5  
8 0  
1
6
0
B E E F W E L L  
P O R K  
7 7  
7 0  
6 0  
V E A L  
1 4 0  
H A M  
B E E F M E D .  
0
2
1
B E E F R A R E  
C O O K E D H A M  
12. Después de cocinar, siempre desconecte el ahumador del tomacorriente.  
Permita que el ahumador se enfríe completamente, luego siga las  
instrucciones en las secciones de “Seguridad para después del uso y  
Mantenimiento y cuidado adecuados” de este manual.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 21  
1. Quite la tapadera de domo y la unidad principal de la bandeja de base.  
2. Coloque una rejilla para cocinar sobre la bandeja de base.  
Asar  
3. Coloque la comida sobre la rejilla para cocinar en una sola capa dejando  
espacios entre cada pieza.  
4. Coloque la tapa de domo sobre la bandeja de base y conecte la parilla al  
tomacorriente. Para lograr mejores resultados, la tapa de domo debiera estar  
puesta sobre la bandeja de base cuando esté asando comida.  
ADVERTENCIA: Use siempre un tomacorriente de 3 cables con conexión a tierra  
cableado para 120 voltios que esté protegido por un interruptor de  
circuito de falla conectado a tierra (GFCI, por sus siglas en inglés) a  
15 ó 20 amperios. En caso de duda llame a un electricista  
calificado. No opere esta parrilla con otro electrodoméstico o  
aparato eléctrico en el mismo circuito.  
5. Use siempre un termómetro de carne para asegurar que la comida esté  
completamente cocida antes de quitarla del ahumador.  
ADVERTENCIA: Cuando esté asando, el goteo de la carne podría causar llamaradas.  
Tenga extrema precaución cuando quite la tapa de domo. Levante la  
tapa de domo inclinándola hacía usted, para permitir que el calor y  
las llamas escapen en la dirección opuesta a la suya. Si ocurre una  
llamarada, vuelva a poner la tapa y desconecte la parrilla para  
sofocarla. No use agua para extinguir fuego de grasa.  
6. Después de cocinar, desconecte siempre la parrilla del tomacorriente. Permita  
que la parrilla se enfríe completamente y luego siga las instrucciones  
contenidas en las secciones de “Seguridad para después del uso y  
Mantenimiento y cuidado adecuados” de este manual.  
Para conseguir su sabor ahumado favorito, experimente usando pedazos, palos y  
trozos de madera que produzca sabor, tal como nogal, pecana, manzana, cereza o  
mezquite. La mayoría de maderas de árboles frutales o de nueces pueden ser  
usadas para ahumar. No use maderas resinosas como el pino, pues producirán un  
sabor desagradable.  
Madera Saborizante  
Los trozos de madera o palos de 3" (7.62 cm) a 4" (10.16 cm) de largo y  
2" (1.27 cm) a 1" (2.54 cm) de grosor funcionan mejor. Salvo que la madera aún  
esté verde, sumérjala en agua durante 20 minutos o envuelva cada pedazo en  
aluminio y abra pequeños agujeros en el aluminio para producir más humo e  
impedir que la madera se queme demasiado rápido. No se necesita demasiada  
madera para lograr un buen sabor ahumado. La cantidad recomendada son 3-4  
trozos o palos. Experimente utilizando más madera para un sabor ahumado más  
fuerte o menos para uno más suave.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 22  
No debiera tener que agregar madera saborizante adicional durante el proceso de cocción, sin embargo,  
Para Agregar  
Leña Mientras  
Cocina  
podría ser necesario cuando esté cocinando pedazos de carne muy grandes. Siga las instrucciones y  
precauciones que aparecen abajo para evitar lesiones cuando agregue madera.  
1. Desconecte el ahumador del tomacorriente. Quite la tapa de domo inclinándola hacia usted para permitir  
que el calor y el vapor escapen en la dirección opuesta a la suya. Tenga precaución pues puede haber  
una llamarada cuando el aire fresco entre repentinamente en contacto con el fuego de grasa.  
2. Usando guantes resistentes al calor, quite la comida de las rejillas para cocinar y luego el ahumador de  
la bandeja de base.  
ADVERTENCIA: El agua en la bandeja para agua estará extremadamente CALIENTE. Cuando levante la  
unidad principal del ahumador, hágalo con extrema precaución y asegúrese de que la  
bandeja para agua esté seguramente colocada en su lugar sobre los tres soportes de  
apoyo. Mantenga sus piernas y pies debajo de la unidad principal del ahumador para  
evitar quemarse con los líquidos calientes que se derramen de la bandeja para agua. Sea  
extremadamente cuidadoso para no voltear o desbalancear el ahumador para que el  
agua caliente no se derrame de la bandeja para agua.  
3. Ponga la unidad principal del ahumador, con la bandeja para agua adentro, en una superficie dura,  
nivelada y no inflamable.  
4. Párese a una distancia segura y use tenazas largas para colocar la madera saborizante sobre las  
piedras volcánicas. No permita que la madera saborizante entre en contacto con el elemento eléctrico.  
5. Ponga de nuevo la unidad principal del ahumador con la bandeja para agua sobre la bandeja de base.  
ADVERTENCIA: El agua en la bandeja para agua estará extremadamente CALIENTE. Cuando levante la  
unidad principal del ahumador del suelo, tenga extrema precaución y asegúrese de que  
la bandeja para agua esté seguramente colocada en su lugar sobre los tres soportes de  
apoyo. Mantenga sus piernas y pies debajo de la unidad principal del ahumador para  
evitar quemarse con los líquidos calientes que se derramen de la bandeja para agua. Sea  
extremadamente cuidadoso para no voltear ni desbalancear el ahumador para que el  
agua caliente no se derrame de la bandeja para agua.  
6. Regrese la comida sobre las rejillas para cocinar y ponga la tapa de domo sobre la unidad principal del  
ahumador.  
7. Conecte de nuevo el ahumador al tomacorriente y permita que la comida continúe cocinándose.  
Revise el nivel de agua en la bandeja para agua si el proceso de cocción toma más de 2 horas. Puede  
detectarse que el nivel de agua está bajo cuando se escucha el sonido siseante del agua. El agua puede  
agregarse a la bandeja para agua a través de la parte superior del ahumador o por la puerta lateral.  
Tenga precaución y siga las instrucciones cuidadosamente.  
Para Agregar  
Agua Mientras  
Cocina  
ADVERTENCIA: No derrame agua sobre el elemento eléctrico.  
OPCIÓN 1: Para agregar el agua a través de la parte superior del ahumador  
1. Desconecte el ahumador del tomacorriente.  
2. Levante la tapa de domo de la unidad principal del ahumador inclinándola hacia usted para permitir  
que el calor y el vapor escapen en la dirección opuesta a la suya. Tenga precaución, pues puede  
haber llamaradas cuando el aire fresco entre repentinamente en contacto con el fuego. Inspeccione  
el nivel de agua en la bandeja.  
3. Si el nivel de agua está bajo, agregue agua a la bandeja. Si la comida está únicamente sobre la rejilla  
para cocinar superior, el agua podría ser agregada moviendo hacia un lado la comida en la rejilla  
para cocinar y echando el agua a través de ésta. Llene la bandeja para agua hasta 1" (2.54 cm) por  
debajo del borde. Échela lentamente para evitar salpicaduras o derramamientos.  
Si está utilizando ambas rejillas para cocinar, utilice guantes resistentes al calor para quitar la comida  
y la rejilla para cocinar superior. Mueva la comida hacia un lado en la rejilla para cocinar inferior y  
eche el agua a la bandeja para agua a través de la rejilla para cocinar inferior. Échela lentamente para  
evitar salpicaduras o derramamientos.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 23  
4. Ponga la rejilla para cocinar en los soportes de apoyo superiores y  
coloque la comida de nuevo sobre la rejilla para cocinar.  
5. Coloque la tapa de domo sobre la unidad principal del ahumador.  
Conecte de nuevo el ahumador al tomacorriente y permita que la  
comida continúe cocinándose.  
1" (2.5 cm)  
OPCIÓN 2: Para agregar agua a través de la puerta lateral  
1. Desconecte el ahumador del tomacorriente.  
2. Aléjese y cuidadosamente abra la puerta lateral. Tenga precaución  
pues puede haber llamaradas cuando el aire fresco entre  
repentinamente en contacto con el fuego. Inspeccione el nivel de agua  
en la bandeja.  
3. Si el nivel de agua está bajo, agregue agua a la bandeja para agua.-  
Aléjese y con cuidado agregue el agua usando un embudo o  
contenedor con boquilla. Llene la bandeja de agua hasta 1" (2.54 cm)  
por debajo del borde. Eche el agua lentamente para evitar salpicaduras  
o derramamientos.  
4. Cierre la puerta lateral y conecte de nuevo el ahumador al  
tomacorriente. Permita que la comida continúe cocinándose.  
Puede lograrse una variación en sabor agregando vino, refrescos,  
hierbas, especias, pedazos de cáscaras de frutas cítricas, jugo de fruta,  
cebollas o marinadas a la bandeja para agua.  
Consejos de Cocina  
Con una brocha ponga aceite de cocina, margarina o mantequilla sobre  
las carnes naturalmente magras y aves antes de cocinar.  
La carne debe de estar completamente descongelada antes de cocinar.  
Cuando cocine más de un pedazo de carne, el tiempo de cocción lo  
determina el pedazo más grande que se esté cocinando.  
La carne se baña sola mientras se cocina en el ahumador. No es  
necesario bañarla ni voltearla luego de que ha sido colocada sobre la  
parrilla. Para más variedad, salsa de barbacoa o una marinada pueden  
ser aplicadas a la carne antes de colocarla en la parrilla.  
Hay muy poca diferencia en temperatura y tiempo de cocción entre los  
niveles superior e inferior de la parrilla. Cuando cocine diferentes tipos o  
cortes de carne al mismo tiempo, coloque la carne que requiere el  
menor tiempo de cocción en la rejilla para cocinar superior, para que  
pueda ser quitada de primero fácilmente. Si sólo necesita una rejilla para  
cocinar, use la rejilla del nivel superior para mejores resultados.  
Durante el proceso de ahumado, evite la tentación de levantar la tapa de  
domo para revisar la comida. Levantar la tapa de domo permite que el  
calor escape, haciendo que sea necesario un mayor tiempo de cocción.  
Use siempre un termómetro de carne para determinar el punto  
apropiado de cocción. Muchas variables (temperatura exterior, la  
cantidad de veces que se ha levantado la tapa de domo, cercanía de la  
comida a la fuente de calor, etc.) afectarán los tiempos reales de  
cocción. Cuando use un termómetro de carne, inserte la sonda hasta la  
mitad de la parte más gruesa de la carne, asegurándose de que no toque  
grasa ni huesos. Permita que pasen cinco minutos para que el  
termómetro marque bien la temperatura.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 24  
SEGURIDAD PARA DESPUÉS DEL USO  
ADVERTENCIA  
No hay interruptor de ENCENDIDO/APAGADO. Siempre apague el ahumador desconectando el cable del tomacorriente cuando  
agregue agua y madera, o cuando termine de cocinar.  
Siempre permita que el ahumador y sus partes se enfríen completamente antes de manipularlos.  
Antes de desatender el ahumador, las brasas y cenizas restantes deben ser quitadas del ahumador. Tenga precaución para  
protegerse a sí mismo y a su propiedad. Coloque las brasas y cenizas restantes en un contenedor de metal no inflamable y  
satúrelos con agua por completo. Permita que las cenizas y el agua permanezcan en el contenedor durante 24 horas previo a  
desecharlas.  
Las brasas y cenizas extinguidas deben de ser colocadas a una distancia segura de todas las estructuras y materiales  
inflamables.  
Cubra y guarde el ahumador adentro en lugar seco, fuera del alcance de los niños.  
Lave la bandeja para agua y las rejillas para cocinar con agua jabonosa caliente ,  
Mantenimiento  
enjuáguelas bien y séquelas. Cubra las rejillas para cocinar con una ligera capa de  
aceite vegetal o aerosol vegetal para cocinar.  
y Cuidado Adecuados  
Limpie el interior y exterior del ahumador con un trapo húmedo. Aplique una ligera  
capa de aceite vegetal o aerosol vegetal para cocinar a las superficies interiores de  
la tapa de domo y de la unidad principal del ahumador para prevenir el óxido.  
Cuando el elemento eléctrico se haya enfriado completamente, límpielo con un  
trapo húmedo después de cada uso. Permita que el elemento eléctrico se seque al  
aire libre fuera de la bandeja de base para que toda la humedad se evapore  
completamente antes de guardarlo.  
Limpie las piedras volcánicas periódicamente con una solución de agua y  
bicarbonato de sodio. Enjuáguelas bien y permita que se sequen completamente al  
aire libre antes de guardarlas.  
Si apareciera óxido en la superficie exterior de su ahumador, limpie y pula la  
superficie con lana de acero o con una tela fina para esmerilar. Retoque con una  
buena pintura resistente a temperaturas altas.  
Nunca aplique pintura a la superficie interior. Las manchas de óxido en el interior  
pueden ser pulidas, limpiadas y luego cubiertas con una ligera capa de aceite  
vegetal o aerosol vegetal para cocinar para minimizar el óxido.  
Siempre mantenga cubierto su ahumador cuando no esté en uso para protegerlo  
del óxido excesivo. La cubierta Smoke’N Grill puede ser encargada directamente  
de Brinkmann llamando al 800-468-5252.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7085-K_Gour Elec_Eng-SP.qxd 11/1/07 2:28 PM Page 1  
ONE YEAR LIMITED WARRANTY  
For one year from date of purchase, The Brinkmann Corporation warrants the Gourmet Electric Smoker against defects due to workmanship or  
materials to the original purchaser. The Brinkmann Corporation’s obligations under this warranty are limited to the following guidelines:  
This warranty does not cover smokers that have been altered or damaged due to: normal wear, rust, abuse, improper maintenance, improper use,  
disassembly of parts and/or attempted repair by anyone other than an authorized employee of The Brinkmann Corporation.  
This warranty does not cover surface scratches or heat damage to the finish, which is considered normal wear.  
The Brinkmann Corporation may elect to repair or replace damaged units covered by the terms of this warranty.  
This warranty extends to the original purchaser only and is not transferable or assignable to subsequent purchasers.  
The Brinkmann Corporation requires reasonable proof of purchase. Therefore, we strongly recommend that you retain your  
sales receipt or invoice. To obtain repair or replacement of your Gourmet Electric Smoker under the terms of this warranty, please call Customer Service  
Department at 800-527-0717 for a Return Authorization Number and further instructions. A receipt will be required. A Return Authorization Number  
must be clearly marked on the outside of the box. The Brinkmann Corporation will not be responsible for any smokers forwarded to us without a  
Return Authorization Number.  
EXCEPT AS ABOVE STATED, THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY.  
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR  
FROM THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE  
LIMITATION MAY NOT APPLY TO YOU.  
ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE OF THE GOURMET ELECTRIC SMOKER  
TO COMPLY WITH THIS WARRANTY OR ANY IMPLIED WARRANTY IS EXCLUDED. CUSTOMER ACKNOWLEDGES THAT THE PURCHASE PRICE  
CHARGED IS BASED UPON THE LIMITATIONS CONTAINED IN THE WARRANTY SET OUT ABOVE. SOME STATES DO NOT ALLOW THE EXCLUSION  
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS  
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.  
GARANTÍA LIMITADA DE UN AÑO  
Por un año a partir de la fecha de compra, The Brinkmann Corporation garantiza el ahumador eléctrico Gourmet contra defectos debidos a la mano de  
obra o materiales, al comprador original. Las obligaciones de The Brinkmann Corporation bajo esta garantía están limitadas a los siguientes  
lineamientos:  
Esta garantía no cubre ahumadores que han sido alterados o dañados debido al: desgaste ordinario, óxido, abuso, mantenimiento inapropiado, uso  
inapropiado, desensamblaje de piezas y/o el intento de reparación por cualquier persona que no sea un empleado autorizado de The Brinkmann  
Corporation.  
Esta garantía no cubre rayones en la superficie ni daño al acabado provocado por el calor cuando es considerado desgaste ordinario.  
The Brinkmann Corporation puede elegir reparar o reemplazar unidades dañadas cubiertas bajo los términos de esta garantía.  
Esta garantía se extiende al comprador original únicamente y no es cedible ni asignable a compradores subsecuentes.  
The Brinkmann Corporation requiere una prueba de compra razonable. Por lo tanto le recomendamos fuertemente que conserve su recibo o factura.  
Para obtener reparaciones o el reemplazo de su ahumador eléctrico Gourmet conforme a los términos de esta garantía, por favor llame al  
Departamento de Servicio al Cliente al 800-527-0717 para que le den un Número de Autorización de Devolución y otras instrucciones. Un recibo o  
prueba de compra será necesario. Un Número de Autorización de Devolución debe aparecer en el exterior de la caja. The Brinkmann Corporation no se  
hará responsable por cualquier ahumador que le sea remitido sin un Número de Autorización de Devolución.  
SALVO EN CUANTO A LO ANTERIORMENTE INDICADO, THE BRINKMANN CORPORATION NO HACE OTRA GARANTÍA EXPRESA.  
LAS GARANTÍAS IMPLÍCITAS DE CALIDAD E IDONEIDAD PARA UN FIN CONCRETO ESTÁN LIMITADAS EN DURACIÓN A UN AÑO A PARTIR DE LA  
FECHA DE COMPRA. ALGUNOS ESTADOS NO PERMITEN LIMITACIONES EN CUANTO AL TIEMPO DE DURACIÓN DE UNA GARANTÍA IMPLÍCITA,  
POR LO QUE LA ANTERIOR LIMITACIÓN PODRÍA NO APLICARLE A USTED.  
CUALQUIER RESPONSABLIDIDAD POR DAÑOS INDIRECTOS, INCIDENTALES O EMERGENTES RESULTANTE DE FALLAS DEL AHUMADOR  
ELÉCTRICO GOURMET PARA CUMPLIR CON ESTA GARANTÍA O CUALQUIER GARANTÍA IMPLÍCITA QUEDA EXCLUIDA. EL CONSUMIDOR ACEPTA  
QUE EL PRECIO DE COMPRA ESTÁ BASADO EN LAS LIMITACIONES CONTENIDAS EN LA GARANTÍA ESTABLECIDA ARRIBA. ALGUNOS ESTADOS  
NO PREMITEN LA EXCLUSIÓN NI LIMITACIÓN DE LOS DAÑOS INDIRECTOS, INCIDENTALES O EMERGENTES, ASÍ QUE LA LIMITIACIÓN O  
EXCLUSIÓN QUE APARECE ARRIBA PODRÍA NO APLICARLE A USTED. ESTA GARANTÍA LE DA A USTED DERECHOS LEGALES ESPECÍFICOS, Y  
USTED TAMBIÉN PODRÍA TENER OTROS DERECHOS QUE VARÍAN DE ESTADO A ESTADO.  
©2005 The Brinkmann® Corporation  
Owner’s Manual for Models/Manual del Propietario para Modelos  
:
Dallas, Texas 75244  
810-7080-0 (black/negro), 810-7080-K (red/rojo),  
810-7090-S  
140-7085-K  
11/07  
Download from Www.Somanuals.com. All Manuals Search And Download.  

BenQ Computer Monitor FP91G User Manual
Billy Goat Yard Vacuum KD512, KD512HC, KD512HCS User Manual
Blanco Indoor Furnishings 501 119 10 User Manual
Bosch Appliances Water Heater GWH 635 ES User Manual
Braun Food Processor K 700 User Manual
Bushnell Binoculars 13 7507 User Manual
Cadence Stereo Equalizer CEQ 600 User Manual
Canon Digital Camera 0206B001 User Manual
Casio Watch QW 1848 User Manual
Christie Digital Systems Projector DS+650 User Manual