OWNER’S MANUAL
ASSEMBLY AND OPERATING INSTRUCTIONS
KEEP THIS MANUAL FOR FUTURE REFERENCE
READ THIS MANUAL
This instruction manual
contains important
information necessary for
the proper assembly and
safe use of the appliance.
Read and follow all
WARNING
FAILURE TO FOLLOW ALL WARNINGS
AND INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN PROPERTY
DAMAGE, PERSONAL INJURY OR
DEATH.
warnings and instructions
before assembling and
using the appliance. Follow
all warnings and
instructions when using
the appliance.
FOR ALL 815-3500 and
816-3500 SERIES.
IM
PO
RT
AN
T
S
AF
EG
UA
RD
•
•
DO
NO
T
REM
OVE
THIS
TAG
TUR
N
G
USI
OFF
A
S
NOT FOR COMMERCIAL USE.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
• For OUTDOOR use only. Do NOT use in a building, home, garage, balcony, porch, tent
or any other enclosed area.
• Smoking oil is an indication that the oil is too hot and may ignite. Oil ignites at varying
temperatures; therefore, never allow the oil to exceed 400°F (200°C) and NEVER LEAVE
HEATING OIL UNATTENDED.
• Carefully monitor the temperature of the oil with the thermometer and regulate the
temperature so that it does not reach the "Fire Hazard" zone on the thermometer.
If necessary, turn the gas OFF to the appliance to allow the oil to cool.
• When cooking with oil or grease, the thermometer provided MUST be used. Follow
instructions in this manual for proper installation and use of the thermometer. If the
thermometer supplied with this fryer/boiler has been lost or damaged, a replacement
thermometer must be obtained before using this fryer. Use only replacement
thermometer # 072-0012-0. This thermometer can be obtained by contacting The
Brinkmann Corporation at 1-800-527-0717.
• Test the thermometer before each use by inserting it into a boiling pot of water and
ensure that it registers approximately 212°F +/- 20˚F (100°C +/- 10˚C). If the
thermometer does not function properly, a replacement thermometer must be
obtained before using this fryer. Use only replacement thermometer # 072-0012-0. This
thermometer can be obtained by contacting The Brinkmann Corporation
at 1-800-527-0717.
• If the temperature exceeds 400°F (200°C) or if oil begins to smoke, immediately turn
the burner or gas supply OFF and wait for the temperature to decrease to less than
350°F (175°C) before relighting burner. (See instructions on page 10 for relighting.) If
there is a lid (cover), do not remove the lid as oxygen will feed a fire.
• Never overfill the cooking vessel with oil, grease or water. Follow instructions in this
manual for establishing proper oil, grease or water levels. (see page 11)
• When cooking with oil/grease, have a type BC or ABC fire extinguisher readily available.
In the event of an oil/grease fire immediately call the Fire Department. Do not attempt
to extinguish with water. A Type BC or ABC fire extinguisher may, in some
circumstances, contain the fire.
• Do NOT use lid when heating or cooking with oil.
• When cooking, the fryer/boiler must be on a level, stable, noncombustible surface in an
area clear of combustible material. An asphalt surface (blacktop) may not be
acceptable for this purpose.
• Do not store or use gasoline or other liquid/aerosols with flammable vapors in the
vicinity of this fryer.
• Do NOT operate appliance any closer than 10 feet from any combustible materials
including walls or railings or under overhead construction as these materials could
ignite should grease fire occur.
• Do NOT install or use in or on recreational vehicles and/or boats.
• In the event of rain, snow, hail, sleet or other forms of precipitation while cooking
with oil/grease, cover the cooking vessel immediately and turn off the appliance
burner and gas supply. Do not attempt to move the appliance or cooking vessel.
• Introduction of water or ice from any source into the oil/grease may cause overflow and
severe burns from hot oil and water splatter. When frying with oil/grease, all food
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
products MUST be completely thawed and towel dried before being immersed in the
fryer.
• Do not leave the appliance unattended. Keep children and pets away from the
appliance at all times. Carefully monitor all activity around fryer to avoid burns or other
injuries.
• Do not place empty cooking vessel on the appliance while in operation as it could
melt. Use caution when placing anything in cooking vessel while the appliance is in
operation.
• Check all gas connections by following directions in the "Gas Leak Testing" section on
page 8 of this manual. Never test for gas leaks with a lighted match or open flame. Do
not operate this fryer with a gas leak.
• Storage of this appliance indoors is permissible only if the cylinder is disconnected
and removed from the appliance and left outdoors. Cylinders must be stored outdoors
out of the reach of children and must not be stored in a building, garage or any other
enclosed area.
• The pressure regulator and hose assembly supplied with the appliance must be used.
Replacement pressure regulators and hose assemblies may be purchased by calling
1-800-527-0717.
• Use caution when walking or standing near fryer as splattered oil may have created a
slick surface.
• Avoid bumping of or impact with the appliance to prevent spillage or splashing of
hot cooking liquid.
• Never drop food or accessories into hot cooking liquid. Lower food and accessories
slowly into the cooking liquid in order to prevent splashing or overflow. When removing
food from the appliance care shall be taken to avoid burns from hot cooking liquids.
• Hot oil or water can cause severe burns and permanent disfigurement; use caution and
common sense when operating this product.
•
DO NOT use external electrical sources with this appliance.
• Clean and inspect the hose before each use of the appliance. If there is evidence of
abrasion, wear, cuts or leaks, the hose must be replaced prior to the appliance being
used. Only use replacement hose # 155-3500-0. This hose can be obtained by
contacting The Brinkmann Corporation at 1-800-527-0717. Replace hose at least
every two years.
• Keep the fuel supply hose away from any heated surfaces.
• The use of alcohol, prescription or non-prescription drugs may impair your ability to
properly assemble or safely operate this appliance. Use caution and common sense.
• Do not move the appliance when in use. Allow the cooking vessel to cool to 115˚F
(45˚C) before moving or storing.
• This appliance is not intended for and should never be used as a heater.
• This appliance will be hot during and after use. Use insulated oven mitts or gloves for
protection from hot surfaces or splatter from cooking liquids.
• Never use a cooking vessel larger than 36 quarts or one that does not fit within the
retaining brackets of the fryer stand.
• Do not use this fryer for other than its intended purpose.
• Combustion by-products from the use of this product contain chemicals known to the
State of California to cause cancer, birth defects, or other reproductive harm.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INFORMATION:
The installation of this appliance must be in accordance with:
All applicable local codes, or in the absence of local codes, either:
•
•
•
National Fuel Gas Code/ANSI Z223.1/NFPA 54
Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58
Natural Gas and Propane Installation Code CSA B149.1
To check your local codes, see your local LP gas dealer or natural gas company.
This fryer was not intended to be connected to a natural gas supply line.
WARNING
LP GAS CYLINDER (NOT SUPPLIED WITH THIS FRYER)
The LP (Liquid Propane) gas cylinder specifically designed to be used with this fryer must have
a 20 lb. (9.1 kg) capacity incorporating a Type 1 cylinder valve and an over-filling protection
device (OPD).
•
DO NOT connect this fryer to an existing #510 POL cylinder valve with Left Hand threads.
The Type 1 valve can be identified with the large external threads on the valve outlet.
•
•
DO NOT connect to a propane cylinder exceeding this capacity.
DO NOT connect to a cylinder that uses any other type of valve connection device.
CYLINDER SPECIFICATIONS:
When purchasing or exchanging a cylinder for your gas fryer, it must be constructed and marked in
accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation
(DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for the
Transportation of Dangerous Goods as applicable with a listed over-filling prevention device (OPD).
The cylinder must also be equipped with:
•
•
•
•
•
•
A shut-off valve terminating in a Type 1 gas cylinder valve outlet.
A Type 1 valve that prevents gas flow until a positive seal is obtained.
An arrangement for vapor withdrawal.
A collar to protect the cylinder shut-off valve.
A safety relief device having direct communication with the vapor space of the cylinder.
A listed over-filling prevention device (OPD).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
•
•
•
•
•
•
•
•
•
Turn off the cylinder valve when your fryer is not in use.
Handle the tank with care.
Always secure the cylinder in an upright position.
Never connect an unregulated LP gas cylinder to your fryer.
DO NOT expose LP gas cylinders to excessive heat or ignition sources.
DO NOT store a spare LP gas cylinder near your fryer.
Allow only qualified LP gas dealers to fill or repair your LP gas cylinder.
DO NOT allow the cylinder to be filled beyond 80% capacity.
Read and follow all warnings and instructions that are on the cylinder and that accompany this
product.
DANGER
•
Never store a spare LP gas cylinder near your fryer. This could cause excess pressure to be
expelled through the vapor relief valve resulting in fire, explosion, or severe personal injury,
including death.
NOTE: PROPANE GAS IS HEAVIER THAN AIR AND WILL COLLECT IN LOW AREAS.
PROPER VENTILATION IS EXTREMELY IMPORTANT.
•
•
Keep the ventilation opening(s) of the LP gas cylinder enclosure free and clear from
obstructions and debris.
DO NOT insert any foreign objects into the valve outlet. Damage to the back-check could
result. A damaged back-check can cause a leak, possibly resulting in explosion, fire, severe
bodily harm, or death.
WARNING
FILLING THE LP GAS CYLINDER:
•
•
•
Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder.
New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank.
DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a
dangerous condition. Over-filled tanks can build up pressure and cause the relief valve to expel
propane gas vapors. The vapor is combustible and if it comes in contact with a spark source or
flame, an explosion causing severe burns, bodily harm, or death could occur.
•
•
Always use a protective cylinder cap when fryer is not connected to cylinder.
If you exchange a cylinder with a qualified exchange program, be sure the cylinder has
a Type 1 valve and an over-filling prevention device (OPD).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSE AND REGULATOR:
Your fryer is equipped with a Type 1 connection device with
the following features:
1. The system will not allow gas flow from the cylinder until
a positive connection to the valve has been made.
NOTE: The cylinder valve must be turned off before any
connection is made or removed.
2. A thermal device that will shut off the gas flow if the device
is subject to temperatures above 240°F to 300°F (115°C to
150°C). If this should happen, remove the entire regulator
assembly and dispose of properly. A replacement regulator
assembly can be purchased by contacting Brinkmann at
1-800-527-0717. The cause of the excessive heat should
be determined and corrected before using your fryer again.
3. A flow limiting device, when activated, restricts the flow
of gas to 10 cubic feet per hour.
WARNING
•
Never use your fryer without leak testing all gas connections and hoses. See the section on
"Leak Testing" in this manual for proper procedures.
WARNING
The pressure regulator and hose assembly supplied with your gas fryer is designed to work with an
LP gas supply cylinder.
•
•
•
DO NOT attempt to connect it to any other fuel supply source such as a natural gas line.
DO NOT use any other pressure regulator/hose assembly other than the one supplied with your fryer.
DO NOT attempt to adjust or repair the regulator. A replacement regulator can be supplied by
contacting Brinkmann. The regulator is designed to operate at a maximum output pressure of
10 psi ( pounds/square inch).
During assembly and/or replacement of the gas cylinder, keep the gas supply hose free of kinks and/or
damage.
Visually inspect the hose assembly prior to each use for evidence of damage, excess wear, or
deterioration. If found, replace the assembly before using your fryer. Only the Brinkmann supplied
replacement should be used.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
CONNECTING HOSE AND REGULATOR TO AN LP GAS CYLINDER
•
Insure the cylinder valve is CLOSED prior to connecting the LP gas cylinder to your fryer. Turn
the regulator control knob clockwise to properly close the valve. Read and follow all
instructions and warnings on the supply hose safety tags. Read and follow all warnings in this
manual concerning the safe use of LP gas cylinders and the hose and regulator before
connecting cylinder to fryer. Read and follow all warnings on the LP cylinder.
1. Check that the cylinder valve is closed by turning the
knob clockwise.
2. Remove the protective plastic cap from the cylinder valve
and the connection device.
3. Insert the nipple of connection device into the valve outlet.
Insure that the device is centered properly.
4. Turn the large coupling nut clockwise by hand and tighten
to a full stop. Take care not to cross thread the coupling nut
onto the cylinder valve. Do not over-tighten the knob onto
the valve. Do not use tools to tighten connection.
NOTE: If you are unable to make the connection,
repeat steps 3 and 4.
5. Check that the hose does not contain kinks, does not come
into contact with sharp edges, and does not contact
surfaces that may become hot during use.
6. Leak check all fittings before lighting your fryer. See section
on "Leak Testing" in this manual.
DANGER
LEAK TESTING:
To prevent fire or explosion hazard:
•
•
•
•
DO NOT smoke or permit ignition sources in the area while conducting a leak test.
Perform test OUTDOORS only in a well ventilated area.
Never perform a leak test with a match or open flame.
Never perform a leak test while the fryer is in use or while fryer is still hot.
WARNING
WHEN TO PERFORM A LEAK TEST:
•
After assembling your fryer and before lighting for the first time, even if purchased fully
assembled.
•
•
•
Every time the LP gas cylinder is refilled or if any of the gas components are replaced.
Any time your fryer has been moved.
At least once per year or if your fryer has not been used for more than 60 days.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Watch For Bubbles
GAS LEAK TESTING:
1. Create a mixture of 50% water and 50% liquid
dishwashing soap.
2. To turn on the fuel supply, turn the cylinder
valve knob one turn counterclockwise.
3. Apply the soap water mixture to the following:
F
G
A
Supply tank (cylinder) weld
B
Connection nut to cylinder valve
I
M
P
O
R
T
A
•
N
D
T
O
N
S
O
A
E
T
F
E
R
T
S
E
U
M
G
U
R
G
O
U
N
V
G
A
T
A
R
•
C
IN
A
L
H
S
V
S
IS
D
V
K
O
T
T
O
M
N
A
A
G
N
A
N
C
A
E
E
V
.
O
D
F
L
N
U
O
N
O
G
T
A
L
F
A
R
D
.P
R
F
F
S
T
L
E
L
H
.
Back side of connection nut to brass
IS
J
A
E
D
O
R
U
S
V
N
T
E
M
E
T
O
N
L
Y
.
nipple
D
Brass nipple connection into regulator
E
Regulator connection to gas supply
hose
H
F
Gas supply hose connection to
burner assembly
G
The full length of gas supply hose
D
C
B
A
H
Cylinder valve to cylinder
4. Check each place listed (A-H) for growing
bubbles which indicates a leak.
5. Turn OFF gas supply at cylinder valve.
6. Turn ON control knob to release gas pressure in hose.
7. Turn control knob to OFF position.
E
8. Tighten any leaking connections.
9. Repeat soapy water test until no leaks are detected. DO NOT use the fryer if leaks cannot be stopped.
Contact a qualified gas appliance repair service.
10. Turn OFF gas supply at cylinder valve until you are ready to use your fryer.
11. Wash off soapy residue with cold water and towel dry.
12. Wait 5 minutes to allow all gas to evacuate the area before lighting fryer.
NOTE: The leak test must be performed in an area that has adequate lighting in order to see if
bubbles are developing. DO NOT use a flashlight to check for bubbles.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
PRE-START CHECK LIST:
Property damage, bodily harm, severe burns, and death could result from failure to follow these
safety steps. These steps should be performed after the fryer has been assembled, stored, moved,
cleaned, or repaired. DO NOT operate this fryer until you have read and understand ALL of the
warnings and instructions in this manual.
•
•
Insure that the fryer is properly assembled.
Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. Hose
should be at least 3 inches from hot surfaces.
•
•
Leak check all gas connections and hose. See section on "Leak Testing".
Ensure that all electrical supply cords are properly grounded and are kept away from this appliance,
water and hot surfaces. Do not use external electrical sources with this appliance.
•
Position your fryer on level ground in a well ventilated location, a safe distance from combustible
materials, buildings and overhangs. Propane cylinder should be positioned upwind from fryer.
10 ft.
24"
12 ft.
CAUTION! Hose is a trip hazard. Do not walk between fryer and cylinder.
NOTE: Due to the intense heat from burner, it is normal for discoloration to occur on fryer during the first
few uses.
LIGHTING INSTRUCTIONS:
Follow the instructions exactly.
1. Make sure the regulator control knob and cylinder valve are in the OFF positions.
2. Turn on the fuel supply by rotating the cylinder valve counterclockwise to full open.
3. DO NOT stand with head, body, or arms over the fryer when lighting.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert paper match in match holder prior to striking. Strike and place match through lighting hole to
approximately 1/2" (2 to 3 cm) from the burner. We recommend the use of a long wooden match.
5. Slowly turn regulator control knob clockwise until burner lights.
6. If burner does NOT ignite immediately, turn the regulator control knob and cylinder valve to OFF, wait
5 minutes for gas to evacuate and repeat steps 1 through 4 until burner ignites.
7. If the burner does not light within the first few attempts, there is a problem with the gas supply. Turn
off the gas at the burner and cylinder. DO NOT attempt to operate the fryer until the problem is found
and corrected.
HOW TO REIGNITE BURNER:
It is recommended to place lid over cooking vessel before reigniting burner. Follow steps 1 through 4
above, to reignite burner. Use caution when lighting burner, hot oil from cooking vessel may have
splattered and run down the sides of the unit.
BURNER FLAME CHECK
Adjust flame height using regulator control
knob. Rotate air shutter to achieve mostly
blue flame. The air damper mounted on the
back of your burner helps to control the amount
of air that mixes with the LP gas. A blue flame
with little or no yellow flame provides the
Yellow
Blue
2”
1”
0”
best heat. Adjust the air damper until the
desired flame is achieved.
Burner Hole
Regulator Control Knob
Air Hole
Rotating
IMPOR
TAN
•
D
O
T
N
OT
SAFEGU
TU
REM
U
S
R
N
OV
E
ARD
ING GA
TA VA
CO NK LV
S
T
HIS
O
E
N
O
TAG
A
ND
•
FL
NT
.
U
N
OF
TH .P.
F
IS
AM
ROSE
L
E
A
L
US
GA
RE S
DJ
V
AL
TM
VE
T
FO
D
EN
R
O
NL
Y.
Air Shutter
Match Holder
Lighter Hole
NOTE: Make sure the male fitting on the fryer is screwed into the air shutter and tightened securely. Do
not over-tighten as the air shutter needs to move freely in order to adjust air intake. Check the
attachment for proper connection every time propane tank is connected to fryer.
TURNING OFF THE FRYER:
1. Turn OFF the LP cylinder valve.
2. Turn regulator control knob to the OFF position.
NOTE: Turn off LP cylinder first to prevent gas from
being left in the system under pressure.
3. To disconnect valve regulator/hose assembly, turn the
large regulator coupling counter-clockwise by hand.
IM
P
O
R
T
NOAT R
EMOVE THIS TAG
•
DO
N
T
CAUTION!
The LP cylinder valve should always be in the OFF
S
A
F
TU
E
R
G
U
U
N
S
G
A
A
IN
A
LV
S
L
R
D
G
S
TA
V
O
O
N
N
TR
A
•
C
M
K
.
E
E
V
N
FL
O
N
U
O
N
D
P
R
O
G
A
L.
FF
E
TH
.
E
A
IS
A
S
D
A
JU
LV
E
FO
E
S
D
TM
N
T
R
O
N
LY
.
•
or closed position when the fryer is not in use.
To turn off the LP cylinder
valve, turn knob clockwise
until it stops.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
WARNING
Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip
any of the warnings and instructions contained in the preceding sections of this manual.
• Never leave heating oil unattended - it can ignite.
• Smoking oil is an indication that the oil is too hot and may ignite. Oil ignites at varying temperatures;
therefore, never allow the oil to exceed 400˚F and NEVER LEAVE HEATING OIL UNATTENDED.
• Never allow oil to reach "Fire Hazard" zone on the thermometer.
• Never exceed maximum fill line on cooking vessel.
• Make sure fryer is at least 10 ft from all combustible materials including overhangs.
• Aluminum pots will melt if placed over burner empty.
• It will take approximately 20-30 minutes to preheat your oil. Never leave oil unattended during
preheating or cooking process as it can ignite and hot oil is extremely hazardous and should be
monitored at all times.
• Use extreme care when lowering or removing food from hot oil or liquid.
HOW TO DETERMINE PROPER AMOUNT OF OIL
(For Use With Cooking Vessels That Do Not Have Maximum Fill Line)
1. Place the food product on or in the holder. (turkey stand or strainer basket)
2. Place the food product and holder into the empty vessel.
3. Fill the vessel with water just until the food product is completely submerged. (Bird elbows need not be
covered. There must be a minimum of 3 inches between the water level and top of the vessel.)
4. Remove the food product from the vessel and either mark the level on the side of the vessel or
measure the amount of water in the vessel.
5. Remove the water and completely dry the vessel and the food product.
6. This is the amount of cooking oil the vessel is to be filled with to cook the food product.
DEEP FRIED WHOLE TURKEY – USING BOILING POT WITH TURKEY STAND AND
HANGER OR BASKET
NOTE: When deep frying a whole turkey, select a turkey in the 10 to 18 lb. range and thaw completely. (if
using a 36 quart pot, do not exceed 22 lb. turkey.
Step 1:
Determine the amount of oil required by following instructions above. If pot has a spigot, make sure spigot
is tightly closed and safety cap is secure.
WARNING: Fryer thermometer should not be inserted into food or touching food when measuring
temperature of cooking oil. End of thermometer should be below oil level.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2:
Place pot with oil on fryer. Make sure thermometer is clipped to side of pot. Do not use lid when heating
or cooking with oil. Bring liquid to the desired cooking temperature (325°-350°F for frying) approximately
20-30 minutes. Never leave heating oil unattended. It can ignite. Carefully monitor temperature and never
allow oil to reach “Fire Hazard” zone on thermometer.
Step 3:
Pat the turkey dry and sprinkle Brinkmann Fried Turkey Rub’N Spice or other seasoning between skin and
meat of the turkey.
Step 4:
Place seasoned turkey with the neck cavity pointing up on Turkey Stand or place turkey in basket.
Wearing protective gloves and clothing, use the Hanger to slowly lower stand or basket into hot oil. It is
important to maintain a temperature between 325°(150˚C) and 350°F (175˚). Regulate the flame with
regulator control knob as needed. Do not let oil overheat as a fire may result.
Step 5:
Estimate cooking time by the formula of 31/2 minutes of frying time per pound of turkey (example: a 10 lb.
turkey should cook approximately thirty-five minutes). Check doneness with a meat thermometer after
removing turkey from hot oil. Use caution as food will be very hot.
Step 6:
When food is done, turn fryer OFF. Always turn propane cylinder valve OFF first, then turn the regulator
control knob OFF. Allow fryer and oil to cool completely. Never attempt to drain oil or move pot until oil
has cooled below 115˚F (45˚C) - Severe burns could result.
Turkey Stand
7” Strainer
Pan & Basket
Set
14” Strainer
Basket
Basket
WARNING: To remove the Turkey Stand or 7” Strainer Basket, grip the turkey hanger firmly with
both hands and insert through hole at top of Turkey Stand or under notched handle of 7” Stainer
basket. Only use the Turkey Hanger provided with your fryer kit. Use of any other item or hanger
could lead to personal injury.
WARNING: Always remove the Turkey SLOWLY from boiling pot to allow hot liquid to drain. Lifting
Turkey out of pot too quickly may cause hot liquid to splash out of boiling pot and could result in
severe burns for anyone near the pot. Be sure to lift straight up and attain proper clearance above
rim to prevent overturning pot with hot liquid.
WARNING: When using 10 quart Pan & Basket, always hang basket directly over pan on the hang
tab. This allows hot liquid to drain back into the pan. Hanging the basket in any other way could
cause the pan to tip over, spilling hot liquid.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BURNER ASSEMBLY/MAINTENANCE
•
Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors
and liquids.
•
Although your burner is constructed of cast iron, it may rust as a result of the extreme heat and
acids from cooking foods. Regularly inspect the burner for cracks, abnormal holes, and other signs
of corrosion damage. If found, replace the burner.
WARNING: DO NOT obstruct the flow of combustion and ventilation air. Burner tube can become
blocked by spiders and other insects building their nests. A blocked burner tube can
prevent gas flow to the burner and could possibly result in a burner tube fire. To clean
the Burner Assembly follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting the fryer.
1. Turn gas off at regulator control knob and LP cylinder valve.
2. Disconnect hose regulator from burner assembly.
3. Use a narrow bottle brush or a stiff wire bent into a small hook to run through the burner tube.
NOTE: Wear eye protection when cleaning burner.
4. Check each port to make sure air comes out each hole.
5. Wire brush entire outer surface of burner to remove food residue and dirt.
6. If burner is damaged, obtain a replacement burner.
7. Reinstall burner and retaining nuts on support strap inside burner stand.
CLEANING & GENERAL MAINTENANCE
•
•
Check and tighten any loose hardware at least every 6 months.
Clean appliance with mild dishwashing detergent, hot water and sponge. A soft bristle brush can
also be used.
•
Inspect entire appliance including hose & regulator and replace any damaged or worn parts. Use
only parts specified by The Brinkmann Corporation.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY
BEFORE ASSEMBLING OR OPERATING YOUR FRYER.
Inspect contents of the box to ensure all parts are included and undamaged.
FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 1-800-527-0717.
(Proof of purchase will be required.)
Step 1
Insert male fitting through spring and air shutter. Keep
An adjustable wrench is needed to
assemble this fryer.
narrow end of spring facing toward fitting. Attach burner
to male fitting by screwing burner counter-clockwise
onto fitting.
PARTS LIST:
1 Owner’s Manual
1 Fryer Stand
NOTE: Do not over-tighten the male fitting as the air shutter
needs to move freely in order to adjust air intake.
Check the attachment for proper connection every
time propane tank is connected to fryer.
1 Burner Assembly
1 Hose & Regulator with Safety Tag
1 Heat Shield
1 Match Holder
1 Air Shutter
Burner
1 Spring
Air Shutter
Male
OPTIONAL PARTS:
(depending on your model)
1 Boiling Pot and Lid
Fitting
Air Hole
1 Boiling Pot with Spigot and Lid
1 Turkey Stand and Hanger
1 Deep Fry Thermometer
1 7” Strainer Basket
Spring
Step 2
1 14” Strainer Basket
Remove nut from bottom of burner assembly.
Step 3
1 10 qt. Pan and Basket
1 Marinade Injector
Position the stand upside down as shown.
Step 4
Place burner assembly inside stand with threaded bolt
protruding through
support strap as shown.
Step 5
Place Heat Shield on
support strap with
Turkey Fryer Gas Cooker
threaded bolt protruding
through center hole.
Step 6
IM
PO
RT
AN
•
D
O
N
O
T
AF
REM
EGAG
OVE THIS TUA
RD
S
T
TUR
U
N
G
•
N
E
D
C
.
O
O
.
P
O
.
F
F
L
HI
A
S
O
N
.
Thread nut onto bolt
and securely tighten. Do
not overtighten.
0
35
0
30
400
0
25
1
50
2
00
4
5
Step 7
0
10
200
5
0
5
5
0
15
ßC
ßF
55
0
10
50
Set fryer with burner assembly upright on flat surface.
Make sure burner assembly is securely attached to fryer.
PROCEED TO “GAS LEAK TESTING” SECTION ON PAGE 8.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
©2003 The Brinkmann Corporation
Dallas, Texas 75244 U.S.A
90 DAY LIMITED WARRANTY
For 90 days from date of purchase, The Brinkmann Corporation warrants the Boiling Pot with Turkey Stand and Hanger against defects
due to workmanship or materials to the original purchaser. The Brinkmann Corporation’s obligations under this warranty are limited to
the following guidelines:
•
This warranty does not cover Boiling Pot with Turkey Stand and Hanger that have been altered or damaged due to: normal wear,
abuse, improper maintenance, improper use, disassembly of parts and/or attempted repair by anyone other than an authorized
employee of The Brinkmann Corporation.
•
•
•
This warranty does not cover surface scratching or heat damage to the finish, which is considered normal wear.
The Brinkmann Corporation may elect to repair or replace damaged units covered by the terms of this warranty.
This warranty extends to the original purchaser only and is not transferable or assignable to subsequent purchasers.
The Brinkmann Corporation requires reasonable proof of purchase. Therefore, we strongly recommend that you retain your
sales receipt or invoice. To obtain repair or replacement of your Boiling Pot with Turkey Stand and Hanger under the terms of this
warranty, please call Customer Service Department at 1-800-527-0717 for a Return Authorization Number and further instructions. A
receipt or proof of purchase will be required. A Return Authorization Number must be clearly marked on the outside of the box.
Any Boiling Pot with Turkey Stand and Hanger returned to Brinkmann must include your name, address and telephone number. Please
make sure the item is properly packed, postage prepaid, and insured. The Brinkmann Corporation will not be responsible for any Boiling
Pot with Turkey Stand and Hanger forwarded to us without a Return Authorization Number.
EXCEPT AS ABOVE STATED, THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY.
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO 90
DAYS FROM THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE OF THE BOILING POT
WITH TURKEY STAND AND HANGER TO COMPLY WITH THIS WARRANTY OR ANY IMPLIED WARRANTY IS EXCLUDED. CUSTOMER
ACKNOWLEDGES THAT THE PURCHASE PRICE CHARGED IS BASED UPON THE LIMITATIONS CONTAINED IN THE WARRANTY SET
OUT ABOVE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND
YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
ONE YEAR LIMITED WARRANTY
For one year from date of purchase, The Brinkmann Corporation warrants the Cooker against defects due to workmanship or materials
to the original purchaser. The Brinkmann Corporation’s obligations under this warranty are limited to the following guidelines:
•
This warranty does not cover Cooker that have been altered or damaged due to: normal wear, abuse, improper maintenance,
improper use, disassembly of parts and/or attempted repair by anyone other than an authorized employee of The Brinkmann
Corporation.
•
•
•
This warranty does not cover surface scratching or heat damage to the finish, which is considered normal wear.
The Brinkmann Corporation may elect to repair or replace damaged units covered by the terms of this warranty.
This warranty extends to the original purchaser only and is not transferable or assignable to subsequent purchasers.
The Brinkmann Corporation requires reasonable proof of purchase. Therefore, we strongly recommend that you retain your
sales receipt or invoice. To obtain repair or replacement of your Cooker under the terms of this warranty, please call Customer Service
Department at 1-800-527-0717 for a Return Authorization Number and further instructions. A receipt or proof of purchase will be
required. A Return Authorization Number must be clearly marked on the outside of the box. Cookers returned to Brinkmann must
include your name, address and telephone number. Please make sure the cooker is properly packed, postage prepaid, and insured. The
Brinkmann Corporation will not be responsible for any cookers forwarded to us without a Return Authorization Number.
EXCEPT AS ABOVE STATED, THE BRINKMANN CORPORATION MAKES NO OTHER EXPRESS WARRANTY.
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO
ONE YEAR FROM THE DATE OF PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
ANY LIABILITY FOR INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE FAILURE OF THE COOKER TO
COMPLY WITH THIS WARRANTY OR ANY IMPLIED WARRANTY IS EXCLUDED. CUSTOMER ACKNOWLEDGES THAT THE PURCHASE
PRICE CHARGED IS BASED UPON THE LIMITATIONS CONTAINED IN THE WARRANTY SET OUT ABOVE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
140-3530-0
7/03, 1/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|