MODEL 37610701 - 04
PECO OWNERS MANUAL
FOR A SCAG UNI T
P# Q0118
CONGRATULATIONS AND THANK YOU FOR BUYING THIS PECO LAWN VACUUM.
Your new PeCo Vac has been engineered and manufactured to PeCo's high standards for
safety, quality and dependability and ease of operations.
Save This Manual For Future Reference
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Outdoor Power Equipment Institute Recommendations
WARNING TO PURCHASERS OF INTERNAL COMBUSTION ENGINE EQUIPPED
MACHINERY OR DEVICES IN THE STATE OF CALIFORNIA:
The equipment which you have purchased does not have a spark arrester muffler. If this
equipment is to be used on any forest covered and brush covered land or grass covered
unimproved land in the state of California, the law requires that a spark arrester muffler be
installed and be in effective working order. The spark arrester must be attached to the
exhaust system and comply with Section 4442 of the California Public Resources Code.
1. Read the owner's manual carefully and familiar-
7. Always stop Vac engine when emptying the
ize yourself with the proper use of your attachment.
container.
Do not allow anyone who is not acquainted with the
Safety Instructions to use your attachment.
2. Know the controls and how to stop quickly.
READ THE OWNER'S MANUAL!
8. Stop tractor and vac engines and remove spark
plug wire before removing or replacing hose, boot,
blower cone or performing any maintenance.
9. Mow up and down the face of slopes (not steeper
3. Do not allow children to operate the vehicle. Do
than 10 degrees); never across the face of the slope.
not allow adults to operate it without proper instruc-
10. It is recommended that the container be kept
tion.
only half full when negotiating any slopes. Start
mowing on slopes when the container is empty.
11. Inspect your lawn and remove any foreign ob-
jects before mowing. Never deliberately run mower
4. Be especially watchful of children and pets
darting into the area while operating.
5. Keep your eyes and mind on your tractor while
mowing or operating your attachment. Don't let
across any foreign object.
others distract you.
12. Wear ear protection if noise level is offensive.
6. Do not attempt to operate your tractor or mower
when not in the driver's seat.
WARNING!
WARNING!
NEVER operate the mower unless the discharge
guard and either the deflector assembly or the
vacuum collector adapter are fastened securely in
place.
Do not work around the mower deck boot or the
blower area until you are certain that the mower
blades and the blower fan have stopped rotating.
WARNING!
WARNING!
To avoid serious injury, perform maintenance on
the vacuum collector ONLY AFTER STOPPING THE
TRACTOR ENGINE AND WAITING FOR ALL MOV-
ING PARTS TO COME TO A COMPLETE STOP. Set
the parking brake. Always remove the ignition key
before beginning the
For your personal safety, ALWAYS mow UP and
DOWN the face of slopes and NEVER across the
face. NEVER attempt to mow excessively steep
slopes and use caution when turning on any
slope.
maintenance
3
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
MOWER
FRAME
STEP 1:
Remove plate on rear of mower as shown.
Redrill top two holes for a 3/8"-16 hex bolt
to mount Mount Plate onto mower frame.
HOLES TO
MOUNT TO
TRACTOR
FIG. 1-1
DESIGNATION OF
HOLES ON THE
MOUNT PLATE
STEP 2:
B
Use (2) 3/8"-16 x 2" (#K1208) , and (2)
3/8"-16 flange nuts (#K1215) to secure
Mount Plate (A) to mower frame. Use (2)
1" spacers (#S0138) between Mount
Plate (A) and mower frame. Place (1)
Bracket (B) on each side of Mount Plate
(A). Use (1) 3/8"-16 x 3/4" hex bolt (#K1190)
and (1) 3/8"-16 flange nut (#K1215) to
mount each bracket. Use existing bolts
from mower frame to mount Bracket (B)
to mower. Use figure 1-1 to place bolts.
A
4
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 3:
A
Slide Engine Mount Arm (B) into the receiver
on the Mount Plate (A) and fasten by
dropping in ball pin (#J0248). Place Engine/
Blower Assembly onto Engine Mount Arm (B)
and fasten with (4) 5/16"-18 x 1 1/2 hex bolts
(#K1157) and (4) 5/16"-18 flange nuts.Tighten
nuts and bolts.
B
A
STEP 4:
The ears of the Cone (A) should fit underneath
the two threaded bosses on the Blower Face (B).
Secure with (2) 5/16"-18 x 2" cone bolts.
B
TIGHTEN CONE BOLTS BEFORE EACH USE!
Impeller Blade Replacement
To remove: Remove hex bolts from hub then screw the bolts
into threaded holes to remove old blade.
B
A
(This will push the impeller off the hub.) If the
impeller is stuck on hit the base of the impeller
between each vein with a hammer then try the
bolts again.
To replace: Place tapered bushing (A) into hub (B) and align
non-threaded holes with the holes in the hub.
Secure with two 1/4" x 1" hex bolts. Torque to 15 ft. lbs.
5
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
REF. NO.
PART NO.
DESCRIPTION
QTY.
1
2
3
4
5
6
B3749
*******
J6006
*******
*******
*******
E4052A
D4002
A0645
BOOT PLATE
BOOT (SPECIFY DECK SIZE)
7"- 8" HOSE CLAMPS
42" LOWER HOSE
BLOWER CONE
ENGINE/BLOWER/BLADE ASSEMBLY
BLOWER HOUSING
5HP BRIGGS & STRATTON ENGINE
4 BLADE IMPELLAR W/ S4311 BUSHING
W/ 3/4" SHAFT
1
1
2
1
1
1
D1016
A0914
6HP KOHLER ENGINE
4 BLADE IMPELLAR W/ S4302 BUSHING
W/ 1" SHAFT
7
8
9
J6011
*******
V1054
A0023
A0913
A0931
A0929
A0751
B1941
B1926
J0316
A0021
A0022
A0236
A08215
V2002
5"- 6" HOSE CLAMPS
6"x32" UPPER HOSE
INLET
HARDTOP ASSEMBLY
BASE FRAME ASSY
(OPTIONAL) WEIGHT ASSEMBLY
MOUNT PLATE ASSEMBLY
ENGINE MOUNT ASSEMBLY
INSIDE INLET PLATE
OUTSIDE RETAINING PLATE
GAS STRUT
RIGHT HAND HINGE PLATE ASSEMBLY
LEFT HAND HINGE PLATE ASSEMBLY
LATCH ASSEMBLY
2
1
1
1
1
1
1
1
1
1
2
1
1
2
1
10
11
12
14
16
17
18
19
20
21
22
23
24
HARDWARE BAG
Plastic Container 7 cu, ft,
PeCo
6
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
Exploded View of Model 376107
10
9
21
22
11
7
20
19
8
23
7
18
6
17
12
16
3
1
5
14
2
3
4
7
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 5:
Attach Base Frame (A) to Mount Plate (C) and secure by dropping in ball pin
(#J0248). With hood open on the Base Frame (A) insert the 7cu. ft. Canister
(B) and close
C
REAR VIEW OF MOWER
A
B
D
STEP 6:
Place Clamps (A) over each end of
6" Hose (B). Attach one end of hose
onto Blower Housing (C). Attach free
end of hose over Inlet (D).
A
B
C
TIGHTEN CLAMPS!
8
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 7:
Attach Boot Retainer to Boot with 3/8" x 1"
carriage bolts and 3/8" flange nuts as shown.
TIGHTEN NUTS AND BOLTS!
STEP 8:
Lift mower deflector and hang Boot
Plate as shown.
STEP 9:
Place Clamp over each end of Lower
Hose. Attach one end of hose over
the Blower Cone. Tighten Clamp.
Slide free end of hose over Boot and
tighten clamps.
9
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Your Lawn Vac was designed and built to provide years of service with only minor care. Certain
tasks however must be performed to keep it in good operating condition and to avoid costly
repairs. This section describes and provides procedures for the necessary care of the Lawn
Vac.
SCHEDULED CARE
Before Each Use
After Each Use
CARE REQUIRED
Check engine oil.
Check all hose connections.
Clean Collector Box, hoses and engine of all grass and dirt.
Check that all screws, nuts, bolts, pins, etc. are present and
secure.
Every 10 Hours
Storage
Never store your Lawn Vac with a full or partially filled container; decaying grass and leaves
may constitute a fire hazard if left too long. Never leave your vac exposed to the elements.
While the metal parts are protected with a quality paint, the engine and other unprotected parts
may deteriorate if left exposed to rain or snow.
EmptyingTheLawnVac
When the collector becomes full, the blower tone will change. In order to empty the container
- Release the back door by moving the dump handle on the left hand side of the container.
Release the door, push back on the container and the debris falls out. When empty, pull the
box forward; move the dump handle in to properly close the rear door.
Service
PeCo Lawn Vac Owners should record the name and telephone number of their tractor
dealer. Your dealer will be happy to supply replacement parts, accessories and do any
service or repairs to your lawn vac. If for some reason your dealer is unable to service your
lawn vac or supply replacement parts, contact PeCo and include the following information:
Tractor Model: __________________________________ Year of Mfg. _________________
Deck Size: _____________________________________
PeCo Vac Model: _________________________
Vac Serial Number: _______________________________
Date of Purchase: _____ /_______ /________
Dealer Name: _________________________________________________________________
Dealer's City: ___________________________
State: ______________ Zip: __________
Dealers Phone Number: _______________________________
10
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Diagnostic Procedures
Trouble shooting procedures are provided in the chart below. To use these procedures,
first locate the problem description that best describes the trouble that you have encoun-
tered. Check the possible causes one at a time in the list. Correct any problems that are
found and operate the vacuum collector again to verify that you have eliminated the problem.
DO NOT attempt any major repairs without first contacting your dealer.
PROBLEM
CAUSE
SOLUTION
Leaves and Grass
not being picked
up completely.
1. Engine speed too slow
2. Ground speed too fast.
3. Hose plugged.
A. Run at full throttle.
B. Use lower gear
C. Check and tighten all hoses.
D. Unplug hose.
Hoses plug easily.
1. Grass or leaves too wet.
2. Grass too high.
3. Container full.
A. Wait for drier conditions.
B. Reduce tractor ground speed/raise deck.
C. Empty container
4. Grass buildup in boot or
under mower deck.
D. Clean thoroughly.
Vacuum Collector
blower vibrates
excessively.
1. Buildup on blower blades.
2. Bent or chipped blade.
A. Remove cone and clean blades.
B. Contact your dealer or PeCo.
Unit fails to fill box.
1. Engine speed too slow.
2. Buildup on inlet or screen
3. Grass is too wet or long.
A. Run at full throttle.
B. Clean thoroughly.
C. Wait for dryer conditions.
OUTDOOR POWER EQUIPMENT
The Serial Number Plate is located
on the aluminum box near the
dump handle.
Model Number
Serial Number
Arden, North Carolina 28704
11
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
P.O. Box 1197
Arden, North Carolina 28704
1-800-438-5823 or (828) 684-1234 fax-(828) 684-0858
email: [email protected]
PeCo
MODEL 37610701 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
|