Sub-Frame Hitch
Installation
Mfg. No. 1695195
For Prestige / 1800 / 2800, Conquest / 1700 / 2700, &
Broadmoor / 1600 / 2600 Series Tractors
Instructions
This kit is required when installing front mounted
snowthrowers.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Sub-Frame Hitch
Installation Instructions
Ref Part No. Qty. Description
1
2
3
4
5
6
7
8
9
1723292A
1653768A
1931335
1919381
1917356
1917372
105249
1
1
4
4
3
4
1
1
4
1
2
1
2
1
2
1
1
1
1
1
1
2
1
1
8
1
7
6
1
1
1
2
4
1
1
1
1
1
1
1
1
1
1
2
1
1
2
4
4
1
1
SHAFT & HOOK ASSY
CLAMP, Support
CARRIAGE BOLT, 5/16-18 x 1
WASHER, 11/32
LOCKWASHER, 5/16
NUT, 5/16-18
PIN, Round Head, 3/8 x 2-3/8
LIFT LEVER ASSY.
SAFETY CLIP
LIFT ROD
SET COLLAR
SPRING, Compression
SET SCREW, 5/16-18 x 1/2
ROD GUIDE
ROD, Latch
ROD, Hitch
HITCH ASSY.
PIN, Headless, 1/2 x 2
BAR, Lift Link
HAIR PIN CLIP
PLATE, Lock, Hydraulic Lift
SPACER
SCREW, Whiz, 3/8-16 x 2-3/4
CAPSCREW, 3/8-16 x 3/4
WASHER PLAIN, 3/8
BELT GUIDE
LOCKWASHER, 3/8
NUT HEX FULL, 3/8-16
PULLEY-FLAT
1724025
2176012
10 1722946
11 8031007
12 171011
13 1928721
14 1723115
15 1733812
16 1733309
17 1733779A
18 1722819
19 1723795
20 1960033
21 1722469
22 1667812
23 1960244
24 1921971
25 1924940
26 162115
27 1916965
28 1916950
29 171247
30 1666287
31 1666294
32 1923701
33 158227
34 1920415
35 1722963
36 1930651
37 1704743
38 1668282
39 1722972
40 1960268
41 1704741
42 1703371
42 1703372
43 1701600
44 1922130
45 1733814A
46 1960074
47 1921210
48 1928352
49 1724387
50 1677135A
PULLEY ASS'Y
SPACER-BRG
CAPSCREW, 3/8-16 x 2
SPACER
CAPSCREW, 3/8-16 x 1-1/4
PIVOT BRACKET
NUT LOCK, 3/8-16
TRUNNION
SPRING
GUIDE ASS'Y -SPRING
CARRIAGE BOLT, 3/8-16 x 1-1/4
ROD ASS'Y
V-BELT, Single-Stage Blower
V-BELT, Two-Stage Blower
REFLECTOR
CAPSCREW, 3/8-16 x 2-1/4
PUSH BAR LATCH
CLIP
BOLT, .38-16 x 1
NUT- FLG, .38-16
PULLY-FLAT
BELT GUIDE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Sub-Frame Hitch
NOTE: Please read through these instructions and the
instructions of any other attachments before beginning
installation.
Change Pulley & Belt - Two-Stage Blower
Only
1. If using this hitch with a two-stage snowthrower, the
front idler pulley must be switched from the right hand
side of the hitch bracket, to the left, and an additional
3/8 x 1 x 1/2 spacer (B, Figure 3) and 3/8-16 x 2-1/4
capscrew (A) is required. Also install the 1703372
drive belt.
WARNING
Before beginning any service work turn off the
PTO, set the parking brake, turn off the ignition,
and disconnect the spark plug wire(s).
A
INITIAL ASSEMBLY
Assemble Hitch
1. Attach the support clamp (C, Figure 2) and hook
assembly (B) to the hitch. Secure with four 5/16-18 x
1 carriage bolts (A), washers (D), lockwashers (E),
and nuts (F). Do not tighten the hardware at this
time.
B
F
E
F
B
C
D
Broadmoor /
C
E
1600 / 2600
Series
Figure 3. Front Pulley - Two-Stage Applications
D
A. Capscrew, 3/8-16 x 2-1/4
B. Spacer, 3/8 x 1 x 1/2
C. Belt Guide
D. Washers, 3/8
E. Lockwasher & Nut
F. Pulley
Assemble Push Bar Latch
1. Attach Push Bar Latch (B, Figure 4), to hitch. Secure
with four .31-16 x 1 bolts (A), and four .38-16 flange
nuts (C).
A
B
B
Conquest / 1700 /
2700 &
C
A
Prestige / 1800 /
2800 Series
C
A
Two Wheel
D
Four Wheel
Drive Models
Drive Models
E
Figure 4. Assemble Push Bar Latch
F
A. Bolt, .38-16 x 1
B. Push Bar Latch
C. Flange Nut, .38-16
Figure 2. Install Support Clamp
A. 5/16-18 x 1 Carriage Bolt
B. Hook Assembly
D. 11/32 Washer
E. 5/16 Lockwasher
F. 5/16-18 Nut
C. Support Clamp
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Sub-Frame Hitch
Installation Instructions
Snowthrower
& Dozer
Applications
A
B
C
E
D
A
B
Figure 5. Assemble Lift Rod
A. Lift Rod
D
C
C. Spring
B
B. Set Collar
D. Rod Guide
Mower
Applications
A
B
G
Figure 6. Early/Later Lift Links
A. Early Model Lift Link
B. Later Model Lift Link
A
Assemble Lift Rod
1. Install the set collars (B, Figure 4), spring (C), and
rod guide (D) on the lift rod (A) as shown. Final
adjustment of the set collars will be made after the
hitch and attachment are installed.
D
C
F
Figure 7. Connect Lift Link
A. Pin
B. Rear Hole of Lift Bar (Snowthrower Applications)
C. Spacer
INITIAL INSTALLATION
Manual Lift Models
D. Hair Pin Clip
LIFT LINK - EARLY VS. LATER
E. Upper Hole (Snowthrower Applications)
F. Slot of Lift Link (Mower Applications)
G. Lower Hole (Mower Applications)
The early model lift link (A, Figure 6) was used on early
production Conquest/1700/2700 Series tractors. It must
be replaced with the later model lift link (B) included with
this attachment. The later model link works in all appli-
cations. Discard the early model link (A).
LIFT LINK POSITION
The lift link is installed differently depending on what
attachment is being used. Refer to Figure 7 for link
installation information.
Hydraulic Lift Models
1. Fully lower the hydraulic lift. The lift assembly is
spring loaded so it will need to be held in the down
position to perform of the following procedures.
A
B
F
C
2. Remove and retain the flat head pin (B, Figure 8) and
hair pin clip (E) securing the lift cylinder (A) to the lift
shaft assembly (F). Remove and retain the flat wash-
ers.
D
E
Figure 8. Install Lock Plate - Hydraulic Lift Models
A. Lift Cylinder
D. Lock Plate
B. Flat Head Pin (Original)
C. Flat Head Pin (New)
E. Hair Pin Clips
F. Lift Shaft Assy.
3. Mount the lock plate (D) next to the cams on the lift
shaft assembly (F) as shown.
5
4. Install the original flat head pin (B) and new flat head
pin (C) and secure with hair pin clips.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Sub-Frame Hitch
A
B
C
D
E
Figure 9. Install Hitch
A. J-Hooks
B. Hitch Rod
C. Hitch Rod
D. Hook
E. Clamp Plate
5. Push the clamp plate (D) backwards until it is snug
against the lift shaft. Tighten the clamp plate hard-
ware (E).
Install Hitch
1. Slide the hitch under the tractor.
2. Raise the rear of the hitch and place the hook (C)
over the lift shaft.
3. Connect the front of the hitch to the tractor J-hooks
(A, Figure 9) using the hitch rod (B) and a safety clip
in the top holes of the push bar latch.
4. Secure the front of the hitch to the tractor by attach-
ing the hitch rod (C) and a safety clip in the bottom
holes of the push bar latch.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Sub-Frame Hitch
Installation Instructions
D
A
B
C
A
B
C
Figure 11. Install Lift Rod - All Models
A. Lift Lever
B. Lift Rod
C. Clip
Figure 10. Install Lift Lever
A. Lift Lever
B. Lift Shaft
C. Safety Clip
D. Clevis Pin
Install Lift Rod
1. Slide the lift lever (A, Figure 10) onto the end of the
tractor lift shaft (B) under the right side footrest.
2. Use the tabs on the lift lever (A) to capture the tractor
lift arm. Secure in place with a clevis pin (D) and
safety clip (C).
3. Insert the rear of the lift rod (B, Figure 11) into the
bottom of the lift lever (A). Secure with a clip (C).
Install Reflectors
1. Install the two reflectors on the rear of the tractor seat
deck.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Sub-Frame Hitch
Snowthrower
Position
C
D
A
B
E
F
A. Hitch Rod
B. Hitch Rod
C. Lift Lever Extension
D. Lift Link (Manual)
E. Pressure Lock Plate
(Hydraulic)
F. Hook
Figure 12. Normal Installation & Removal
REMOVAL
NORMAL INSTALLATION
NOTE: After removing components, reinstall the clevis
pins and clips to prevent loss.
1. Insert the hook (F, Figure 12) into the back of the
hitch. Mount the rear of the hitch on the lift cross-
shaft.
1. Disconnect the lift rod from the attachment and lift
lever extension (C, Figure 12).
2. Secure the front of the hitch to the J-hooks using the
hitch rod (A) and (B) (Figure 9).
2. Remove the clevis pin and clip from the lift lever (C)
and remove the lift lever.
3. Install the downward pressure lock plate (E) OR
place the lift link (D) in snowthrower position.
3. Remove the front hitch rod (A) and (B). Remove the
hitch and hook (F).
4. Install the lift lever extension (C).
4. Remove the lock plate (E) OR reposition the lift link
(D) in mowing position.
5. Install the lift rod and attachment (Figure 11).
Download from Www.Somanuals.com. All Manuals Search And Download.
Sub-Frame Hitch
Installation Instructions
Snowthrower
& Dozer
Applications
Snowthrower
& Dozer
Applications
E
A
A
B
C
D
F
E
D
C
B
Mower
Applications
Mower
Applications
G
A
A
B
F
E
D
C
F
G
Figure 13. Lift Lock Plate - Hydraulic Lift Models
A. Lift Cylinder
B. Flat Head Pin (Original)
C. Flat Head Pin (New)
D. Lock Plate
Figure 14. Lift Link - Manual Lift Models
A. Pin
B. Rear Hole of Lift Bar (Snowthrower Applications)
C. Spacer
D. Hair Pin Clip
E. Hair Pin Clips
F. Lift Shaft Assy.
G. Washers
E. Upper Hole (Snowthrower Applications)
F. Slot of Lift Link (Mower Applications)
G. Lower Hole (Mower Applications)
LIFT VARIATIONS WHEN USING
ATTACHMENTS
When a front-mounted attachment such as a snowthrow-
er or dozer blade is used with the tractor, the lift mecha-
nism must be locked to provide downward force. When
the mower is reinstalled the downward pressure lock
must be released so that the mower can float.
Manual Lift Models
Hydraulic Lift Models
NOTE: These instructions apply to Conquest / 1700 /
2700 Series tractors or Broadmoor / 1600 / 2600 Series
tractors equipped with a lift lever kit.
When using a snowthrower or dozer, the downward
pressure lock plate (D, Figure 13) and an additional pin
(C) is installed. These parts are included with the attach-
ment. Note that the washers (G) are not used with the
lock plate.
The lift link is installed differently depending on what
attachment is being used. Refer to Figure 14 for link
installation information.
When mowing, the downward pressure lock plate (D) is
removed and replaced with two washers (G). The addi-
tional pin (C) is also removed.
Fully lower the hydraulic lift. The lift assembly is spring
loaded so it will need to be held in the down position to
perform of the following procedures.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Sub-Frame Hitch
NOTES
MANUFACTURING, INC.
Form No. 1734116
Rev. 10/2006
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
© 2006 Briggs & Stratton, Inc. All Rights Reserved
TP 200-4417-00-AT-SMAN
Download from Www.Somanuals.com. All Manuals Search And Download.
|