Aqua Fountain
Instructions for Use
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
These instructions refer to the Breville Water Filter/Chillers AF5 and AF6
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Fig 1
q
w
e
r
s
t
y
u
i
o
a
1. BRITA Memo - cartridge exchange
indicator
6. ON/OFF switch
7. Red power on indicator
8. Chilled water indicator
9. Water dispenser lever
2. Upper water tank cover
3. Hinged lid
4. 1 litre upper water tank
5. 2 litre filtered water tank
10. 1 litre chilled filtered water tank
11. BRITAMAXTRAwater filter
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFOREUSINGYOURWATERFILTER/CHILLER
Before using your water filter/chiller for
the first time, it is recommended that the
unit is flushed through with fresh water.
Pleaseensurethatyoureadthefollowing
instructions before flushing your water
filter/chiller several times.
5. Position the water filter/chiller on a
stable flat surface, close to a mains
power socket, not in direct sunlight
and out of the reach of children.
6. Make sure that there is sufficient
space around the water filter/chiller
to allow the heat extracted during
the chilling process to dissipate.
Leave a gap of at least 15 cm
between the ventilation slots on the
rear of the chiller and any wall or
surface.
1. Remove your water filter/chiller
carefully from the box. You may wish
to store the packaging for future use.
2. Check the contents:
•
•
•
•
•
Water filter/chiller
BRITAMAXTRAwater filter cartridge
User guide
Do not plug the unit in or install the
filter cartridge yet.
7. Lift the hinged lid and using a
suitable jug, pour 2 litres of clean
water into the tank. Place a glass
under the dispenser and push the
dispensing lever back to drain all of
the water. It may take some time for
the water to initially flow through.
BRITA brochure
BRITA registration card
3. Wash the clear plastic lid, upper and
filtered water tanks in warm soapy
water, rinse and dry thoroughly.
4. Reassemble the tanks as shown
below.
8. Repeat this process one more time.
Upper water tank
cover
Upper water tank
Filtered water
tank
Chilled and filtered
water tank
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARINGTHEFILTERCARTRIDGE
1. Remove the cartridge from its
1. Place the upper tank on a suitable
bowl or jug. Fill with cold tap water
up to the MAX FILL LEVEL mark on
the upper water tank and allow the
water to filter through.
wrapping (it is normal for the cartridge
to appear moist during storage - this
is simply condensation).
2. Immerse the cartridge in cold water
and agitate gently to remove any air
bubbles.
Maximum fill level mark
✎NOTE
There is no need to pre-soak this
cartridge before use.
Discard the first two fillings. These
first two fillings are used to flush the
filter cartridge. Place the upper tank
back into the unit.
3. Remove the lid from the upper water
tank.
4. Insert the filter cartridge into the water
tank as shown below. Push it firmly
into place. When correctly fitted, the
cartridge should remain in place
when the tank is turned upside down.
2. Replace the upper water tank lid.
3. Press and hold the START button on
the BRITA Memo on the lid until all of
the bars on the display appear and
flash twice, see “Using the Memo
function” on page 8.
✎NOTE
When it is time to replace the cartridge
after 4 weeks use, simply lift the ring
pull handle on top of the cartridge to
remove. The cartridge may be
disposed of in household waste or
contact the BRITA-Care customer
service for advice on recycling
schemes.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USINGYOURWATERFILTER/CHILLER
1. Lift the hinged lid and using a
4. Plug the unit into the mains supply.
Press the chiller ON/OFF switch on
the front of the unit. The switch will
illuminate and the machine will begin
to chill the water.
suitable jug, carefully pour water into
the tank up to the MAX FILL LEVEL.
This may take some time due to the
action of the filter.
5. Dispense 2 litres of water from the
unit to remove any unfiltered water
from the unit that was used to prepare
the chiller as instructed on page 4.
6. Within approximately 3 hours the blue
indicator on the front of the unit will
light indicating that the water has
chilled to approximately 10OC,
although this may take longer in very
hot weather. The indicator will cycle
on and off as the unit maintains its
temperature, but the unit will continue
to chill the water down to 8OC then
stop. If the water temperature rises
above 8OC the unit will start to chill
again.
2. Keep adding water until all the tanks
are full. Water flows through the
cartridge at a set rate. This is to
achieve the best possible filtration.
Because of this it may take some time
to fill all the tanks on first use. During
normal use top up the tanks regularly.
We recommend that the water chiller
bekeptoutofdirectsunlightandaway
from any heat source.
7. Place a glass under the dispenser
and push the lever back to dispense
water.
✎NOTE
After filling, it is important to vent any
air in the unit otherwise the chiller will
not function correctly. Do this by
pressing the dispensing lever until
the water flows from the dispenser
without any air bubbles present. Once
the water is clear of any air bubbles,
the dispensing lever may be released.
Top up the water tank if necessary.
✎NOTE
It is normal for the indicator to go off
when water is drawn. Water inside
the unit will remain chilled but the
indicator will not come on again until
the optimum temperature has been
reached.
3. Close the hinged lid.
8. Top up the water tank as necessary.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
USINGYOURWATERFILTER/CHILLER
For optimum enjoyment, we recommend
✎NOTE
that if your water chiller has not been
used for 1 day or more, you first draw half
a glass of water and dispose of it. It is
possible to use the unit without power
but the water will not be chilled.
Remember that water is a foodstuff.
Please consume filtered water within 2
days.
There is a risk of leakage from the
split joint between the top tank and
filtered water tank. This may occur if
the unit is moved or disturbed when
both tanks are at maximum capacity.
Toavoidleakage, drawoffwaterusing
the lever to empty the top tank so that
it does not overflow when moved.
To empty filtered water from the system,
use the plug in the base of the chiller as
instructed in the storage section on page
10.
Troubleshooting
Water is not dispensed:
When replacing the bottom 2 litre filtered
water tank, please ensure that there is
no water in the inner well (illustrated
below).
•
Make sure that there is water in the
tank.
•
Air trapped in the filter cartridge may
stop water flowing into the filtered
water tank. The cartridge must be
immersed in cold water and agitated
to removed any air bubbles before
installation.
Inner well
•
•
Filter is blocked. Replace.
Air can become trapped in the
internal tank. Press the dispensing
lever until clear water dispenses
without any air bubbles. This may
take some time.
Chiller light tuning off and on:
If there is water present, dispense the
water using the lever until the well is
empty.
•
The chiller light will not stay on
permanently. It will cycle on and off
as the temperature of the water is
maintained.
Should water spill from the tank it is not
dangerous. Do not grasp or pull on the
tank sections to move or reposition the
unit.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USINGTHEBRITAMEMOFUNCTION
It is important to change your BRITA
water filter cartridge regularly to enjoy
the benefits of BRITA filtered water. The
BRITA Memo system automatically
reminds you when your water filter
cartridge needs to be changed.
%
100
75
50
When you have fitted and prepared your
water filter cartridge, start the Memo
system as follows:
25
•
Press and hold the start button until
four bars appear in the display and
flash twice. The Memo is now set.
The flashing dot in the bottom right
corner of the display will show that
the Memo is working.
•
Every week one bar will disappear to
indicate the remaining cartridge life.
When only one bar is showing, check
that you have a replacement BRITA
MAXTRA water filter cartridge
available.
%
100
75
50
25
•
After four weeks, all four bars will
disappear and a flashing arrow will
appear to indicate that the filter
cartridge should be replaced.
Insert a new BRITA water filter
cartridge (as described under
“Changing the BRITA MAXTRA Filter
Cartridge” on page 9) and restart the
Memo as described above.
Please note: The Memo system is only
intended for use with BRITA filter
cartridges.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGINGTHEBRITAMAXTRAFILTERCARTRIDGE
The filter cartridge will need to be
changed approximately once per month.
7. Follow the instructions in “Preparing
the Filter Cartridge” on page 5.
1. Switch the water filter/chiller off and
disconnect from the mains supply.
8. Insert the BRITA MAXTRA filter
cartridge into its receptacle in the
upper water tank.
2. Using the dispenser, (as described
in Cleaning and Maintenance on
page 10) completely drain the water
from the tanks.
9. Replace the upper water tank lid.
10. Restart the BRITA Memo system as
described in “Using the BRITA Memo
Function” on page 8.
3. Remove the upper water tank cover.
4. Pull the BRITAMAXTRAfilter cartridge
out of the unit and discard it.
11. Lift the hinged lid and refill the tanks.
12. Close the hinged lid.
5. Wash the lid and tanks in warm
soapy water, rinse and dry thoroughly.
13. Plug the unit into the mains and press
the chiller ON/OFF switch on the front
of the unit and wait for the water to
chill.
6. Remove the new BRITAMAXTRAfilter
cartridge from its wrapping.
✎NOTE
✎NOTE
Always make sure you have spare
cartridges to hand. When buying
cartridgeslookfortheBRITAMAXTRA
symbol on the cartridge packaging to
find the correct filter cartridge in store.
The cartridge and inside wrapper may
be moist - this is simply condensation.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANINGANDMAINTENANCE
9. To flush through the system pour
Cleaning
approximately 2 litres of water into
the tank, depress the dispensing
lever until water starts to come out of
the dispensing nozzle, and then
empty using the drain plug at the
bottom of the unit over a sink or large
container. Replace the drain plug.
Theoutercasingofyourwaterfilterchiller
can be cleaned using a soft damp cloth
and a non-abrasive cleaner.
It is important that the inside of the chiller
is cleaned regularly. We recommend
that this is done at least monthly e.g.
whenchangingtheMaxtracartridge.Also,
ensure that the dispensing nozzle is
cleaned regularly.
10. Your chiller is now ready to use. Fill
the chiller tanks with tap water as per
chiller instructions, plug the unit into
the socket and turn on. Use the chiller
as normal.
Cleaning Instructions
1. Disconnect the chiller from the
electrical socket and drain all the
water by unscrewing the drain plug
on the bottom of the unit over a sink
or large container.
Storage
Ifyouarenotgoingtouseyourwaterfilter
chiller for an extended time disconnect
the unit from the mains and drain the
water using the drain plug at the bottom
of the unit over a sink or large container.
2. When empty of water replace the
drain plug.
3. Remove the lid and top up the water
tank, leaving the bottom water tank
in place.
Remove the filter cartridge and discard.
Leave the lid off and allow the unit to dry
thoroughly.
4. Pour approximately 2 litres of water
into the bottom tank, and add a non-
tainting sterilising fluid such as Milton
(following manufacturer’s guidelines
for dilution).
If the chiller has not been used for an
extended time, follow the internal
cleaning instructions above before
reusing.
5. Depress dispensing lever until fluid
starts to come out of the dispensing
nozzle.
6. Stop depressing the lever when the
fluid comes through the nozzle.
7. Leave the fluid to stand in the chiller
as recommended by the fluid
manufacturers instructions (normally
approximately 10/15 minutes).
8. Drain the chiller using the drain plug
at the bottom of the unit over a sink or
large container. Replace the drain
plug.
Drain Plug
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANTSAFETYINSTRUCTIONS
✓ Always ensure hands are dry before
handling the plug or switching on the
appliance.
✓ Always use the appliance on a
secure, dry level surface.
✓ Always unwind the power cord before
use.
✘ Never use this appliance outdoors.
✘ Never use this appliance for other
than the intended use. This appliance
is for household use only.
✘ Never immerse any part of the
appliance, cordset or plug in water or
any other liquid to protect against
electrical hazards.
✘ Never use harsh, abrasive or caustic
cleaners to clean this appliance.
✘ Never let the cable hang over the edge
of the worktop, touch hot surfaces or
become knotted.
✘ Never place this appliance on or near
a hot gas or electric burner or where it
could touch a heated oven or microwave
oven.
✘ Never operate any appliance with a
damaged cable or plug or after an
appliance malfunction or if it has been
damaged in any manner.
✘ Never keep the appliance in an
environment below 0oC. Water in the unit
will freeze and cause damage.
✘ Never use any attachment or
accessory not supplied with the
appliance or not recommended by the
appliance manufacturer.
✓ Always carry out regular checks of
the supply cord to ensure no damage
is evident. Should there be any signs
that the cord is damaged in the slightest
degree, the entire appliance should be
returned to the Customer Service
Department.
✓ Always allow 15 cm of air space
above and on all sides for air circulation.
Do not allow the appliance to touch
curtains, wall coverings, clothing,
dishtowels or other flammable
materials during use.
✓ Always use BRITA MAXTRA water
filter cartidges.
✓ Always unplug the appliance from the
mains power supply socket before filling
with water, after use, and before
cleaning.
✓ Always return the appliance after a
malfunction, or if it has been damaged
in any manner to the Customer Service
Department for examination, repair or
adjustment as special purpose tools
are required.
✓ Always ensure that the filter is
securely positioned.
✓ Always reset the BRITA Memo after
changing the filter.
✘ Never fill the water tank with any liquid
other than water.
✘ Never use the water filter/chiller
without a water filter cartridge fitted. The
Breville water filter/chiller is designed
to be used with the BRITA MAXTRAfilter
cartridge.
✘ Never attempt to filter untreated, raw
water or water of unknown quality. This
water filter cartridge must only be used
with municipally treated tap water.
✓ Always Remember that water is a
foodstuff. Please consume filtered water
within 2 days. To empty filtered water
form the unit please use plug in the
base of chiller as instructed in the
storage section on page 10.
✓ Always Clean the inside and
dispenser of the chiller at least every 2-
3 weeks.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION TO THE MAINS SUPPLY
When using electrical appliances, basic safety precautions should always be
followed.
! WARNING
THIS APPLIANCE MUST BE EARTHED
If this appliance is fitted with a rewirable BS1363, 13 amp plug, the fuse should be
rated at 3 amps and be ASTA approved to BS1362. However if the plug is unsuitable,
it should be dismantled and removed from the supply cord and an appropriate plug
fitted as detailed below.
If this appliance is fitted with a moulded BS1363 13 amp plug, the fuse should be
rated at 3 amps and be ASTA approved to BS1362. If the fuse in a non-rewirable plug
needs to be changed, the fuse cover must be refitted. The appliance must not be
used without the fuse cover fitted.
In the event of the plug being unsuitable, it should be changed and an appropriate
plug fitted as detailed below. If you remove the plug it must not be connected to a 13
amp socket and the plug must be disposed of immediately.
As the colours of the wires in the mains lead of this appliance may not correspond
with the coloured markings identifying the terminals in your plug, proceed as follows:
The wires of the mains lead are coloured in accordance with the following code:
GREEN & YELLOW = EARTH
BLUE = NEUTRAL
BROWN = LIVE
The wire which is coloured GREEN & YELLOW must be connected to the terminal
in your plug which is marked with an E or by the EARTH SYMBOL
or coloured
GREENorGREEN&YELLOW.
ThewirewhichiscolouredBLUE
Plug should be BS1363/A approved
Fit a 3 Amp fuse
must be connected to the
terminal in your plug which is
marked with the letter N or
colouredBLACK.
3 Amp
fuse
The wire which is coloured
BROWN must be connected to
the terminal in your plug which
is marked with the letter L or
coloured RED.
BLUE
(Neutral)
BROWN
(Live)
Ifanyotherplugisused, a3amp
fuse must be fitted either in the
plug or adaptor or at the
distributor board.
Ensure that the outer sheath of the cable
is firmly held by the clamp
12
Download from Www.Somanuals.com. All Manuals Search And Download.
AFTER SALES SERVICE
These appliances are built to the very highest of standards. There are no user-
serviceable parts. Follow these steps if the unit fails to operate:
1
2
3
Check instructions have been followed correctly.
Check fuse has not blown.
Check mains supply is functional.
If the appliance will still not operate, return the appliance to the place it was
purchased for a replacement. To return the appliance to the Customer Service
Department, follow the steps below:
1. Pack it carefully (preferably in the original carton). Ensure unit is clean.
2. Enclose your name and address and quote model number AF7 on all
correspondence.
3. Give the reason why you are returning it.
4. If within the guarantee period, state when and where it was purchased and
include proof of purchase (eg. till receipt).
5. Send it to our Customer Service Department at the address below:
Customer Service Department
Pulse Home Products Limited
Vine Mill, Middleton Road,
Royton,
Oldham
OL2 5LN, UK.
Telephone: 0161 621 6900 Fax: 0161 626 0391
6. For BRITA/MAXTRAwater filter cartridge and BRITAMemo queries, contact BRITA
Customer Care Services on:
Telephone: 0870 487 1000
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE
This product is guaranteed for a period of 1 year from the date of purchase against
mechanical and electrical defects.
This guarantee is only valid if the appliance is used solely for domestic purposes
in accordance with the instructions provided, that it is not connected to an unsuitable
electricity supply, dismantled or interfered with in any way or damaged through
misuse. Under this guarantee we undertake to repair or replace free of charge any
parts found to be defective.
Nothing in this guarantee or the instructions relating to the product excludes, restricts
or otherwise affects your statutory rights.
In line with our policy of continuous development, we reserve the right to change this
product, packaging and documentation without notice.
This product is manufactured to comply with the radio interference requirements of
EEC directive 93/68 EEC.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RECYCLING INFORMATION
The Maxtra cartridge in the chiller is 100% recyclable. Look out for BRITA recycling
Waste Electrical and Electronic Equipment (WEEE)
WEEE is the fastest growing waste stream in the UK, growing by at least 5% each
year. The UK public alone dispose of over 1.2 million tonnes of electrical and
electronic waste every year; this would fill the new Wembley Stadium 6 times over.
Much of the UK’s electronic waste ends up in landfill sites. It has been estimated
that landfill space in the UK will run out within the next 10 years if we do not increase
the amount of waste we recycle.
WEEE that is not recycled can have negative impacts on soil, air and water quality
which can lead to environmental damage and which can also lead to negative
impacts on human and animal health.
Recycling household electrical equipment – regulations
With effect from July 2007, the UK’s Waste electrical and Electronic Equipment
(WEEE) Regulation require that all producers of electrical equipment are now
obliged to pay for recycling of household electrical goods, where previously this bill
was met by councils or items were not recycled at all. These regulations also require
that all retailers both actively assist in delivering a UK wide WEEE collection
infrastructure and encourage the participation of consumers in recycling electronic
equipment.
So that you can get your waste electrical goods recycled, we have contributed
towards a national fund to assist local councils to further develop their existing waste
electronics collection facilities, which will in turn allow producers of this equipment
to meet their obligations.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
RECYCLING INFORMATION
The Crossed out Wheeled Bin Symbol
All new electrical and electronic equipment should be marked with the crossed out
wheeled bin, which aims to encourage you to separate out WEEE from other
household waste and to dispose of it at a recycling facility.
recycle-more.co.uk
For advice on all aspects of recycling, to find out how to minimise your effect on the
environment and locate your nearest recycling facilities for electronic waste please
Recycle-more.co.uk also offers top tip and advice on all aspects of recycling, making
it easier and quicker to protect our environment and recycle-more!
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Vine Mill, Middleton Road, Royton, Oldham, OL2 5LN, UK.
Breville is a registered trademark of Pulse Home Products Limited
© Pulse Home Products Limited
92423-6
AF5_6_Iss_8 02/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|