THROUGH-THE-WALL GAS WATER HEATER
A Spanish language version of these instructions is available by contacting
the company listed on the rating plate.
La version espanola de estas instrucciones se puede obtener al escribirle
a la fabrica cuyo nombre aparece en la placa de especificaciones.
TTW INSTALLATION AND OPERATING
INSTRUCTION MANUAL
WARNING: If the information in these instructions is not
followed exactly, a fire or explosion may result causing
property damage, personal injury, or death.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable,
combustible, or corrosive vapors and liquids in the
vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
·
·
Do not try to light any appliance.
Do not touch any electrical switch; do not use any
phone in your building.
·
·
Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier's instructions.
If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
For your family’s comfort, safety and convenience we
recommend Bradford White water heaters to be installed and
serviced by a plumbing professional.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
page
4
GENERAL INFORMATION...............................................................
INSTALLATION.................................................................................
Locating The Water Heater.....................................................
Minimum Clearances...............................................................
Venting......................................................................................
Specifications for
5
5
8
9
48 Gal, 65,000 BTU input (189.3 L, 19.1 kW/Hr)
65 Gal, 65,000 BTU input (246.1 L, 19.1 kW/Hr)
75 Gal, 76,000 BTU input (283.9 L, 22.3 kW/Hr).......... 12
Specifications for
40 Gal, 40,000 BTU input (151.4 L, 11.7 kW/Hr)
48 Gal, 40,000 BTU input (189.3 L, 11.7 kW/Hr).......... 18
Combustion Air Supply.......................................................... 24
Water Connections.................................................................. 26
Gas Connections ..................................................................... 29
Electrical Connections............................................................ 30
Wiring Diagram for
48 Gal, 65,000 BTU input (189.3 L, 19.1 kW/Hr)
65 Gal, 65,000 BTU input 246.1 L, 19.1 kW/Hr)
75 Gal, 76,000 BTU input (283.9 L, 22.3 kW/Hr).......... 31
Wiring Diagram for
40 Gal, 40,000 BTU input (151.4 L, 11.7 kW/Hr)
48 Gal, 40,000 BTU input (189.3 L, 11.7 kW/Hr).......... 32
GENERAL OPERATION.................................................................... 33
Lighting and Shutdown Instructions..................................... 34
Thermostat Adjustment........................................................... 35
Burner Flame Check................................................................ 36
MAINTENANCE................................................................................ 37
PARTS LIST DRAWING.................................................................... 40
PARTS LIST...................................................................................... 40
INSTALLATION INSTRUCTIONS FOR POTABLE WATER AND
SPACE HEATING.............................................................................. 41
VENT PIPE PREPARATION AND JOINING ...................................... 42
NOTES.............................................................................................. 44
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL INFORMATION
This gas-fired water heater’s design is certified by CSA International under the
American National Standard Z21.10.1 - (as indicated on the rating plate) and
CSA 4.1-M - (as indicated on the rating plate).
This water heater must be installed in accordance with local codes or, in the
absence of local codes, the National Fuel Gas Code, ANSI Z223.1-Latest
Edition) and/or in Canada CAN/CGA B149 Installation Codes (Latest Editions).
The warranty for this water heater is in effect only when the water heater is
installed, adjusted, and operated in accordance with these Installation and
Operating Instructions. The manufacturer will not be held liable for any damage
resulting from alteration and/or failure to comply with these instruction
This water heater is not design certified for installation in a mobile home. Such an
installation may create a hazardous condition and will nullify the warranty.
CAUTION
Incorrect operation of this appliance may create a hazard to life and
property and will nullify the warranty.
Do not use this appliance if any part has been submerged in water. You should
contact a qualified service technician to inspect the appliance and to replace any
part of the control system including the combination gas control which has been
submerged in water.
DANGER
Do not store or use gasoline or other flammable, combustible, or
corrosive vapors and liquids in the vicinity of this or any other
appliance.
IMPORTANT
Before proceeding, please inspect the water heater and its components for
possible damage. DO NOT install any damaged components. If damage is
evident then please contact the supplier where the water heater was purchased
or the manufacturer listed on the rating plate for replacement parts.
Make sure that you check the rating plate and combination gas control on the
water heater to be certain that the type of gas being supplied corresponds with
the marking on the rating plate and combination gas control.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
General Information continued-
A sacrificial anode is used to extend tank life. The removal of this anode, for any
reason, will nullify the warranty. In areas where water is unusually active, an odor
may occur at the hot water faucet due to a reaction between the sacrificial anode
and the impurities in the water. If this should happen, an alternative anode may
be purchased from the supplier that installed this water heater. This will minimize
the odor while protecting the tank. Additionally, the water heater should be
flushed with appropriate dissolvers to eliminate any bacteria.
INSTALLATION
Locating The Water Heater
WARNING
Water heaters are heat producing appliances. To avoid damage or injury, do not
store materials against the water heater or vent-air intake system. Use proper
care to avoid unnecessary contact (especially by children) with the water heater
and vent-air intake components. UNDER NO CRCUMSTANCES MUST
FLAMMABLE MATERIALS, SUCH AS GASOLINE OR PAINT THINNER BE
USED OR STORED IN THE VICINITY OF THIS WATER HEATER, VENT-AIR
INTAKE SYSTEM OR IN ANY LOCATION FROM WHICH FUMES COULD
REACH THE WATER HEATER OR VENT-AIR INTAKE SYSTEM.
DO NOT install the water heater in any location where gasoline or
flammable vapors are likly to be present.
Water Heaters in residential garages must be installed so that all burner(s)
and burner ignition device(s) are located not less than 18 inches (46 cm)
above the floor and must be located or protected to avoid physical
damage. For other installations refer to local codes. In the absence of
local codes, the water heater must be installed in compliance with the
National Fuel Gas Code, ANSI Z223.1 - (Latest Edition) and/or in Canada,
CAN/CGA B149 Installation Codes (Latest Editions).
The location of this water heater is of the utmost importance. Before installing
this water heater, read the installation section of these instructions. After reading
these installation and operating instructions, select a location for the water heater
where the floor is level and is easily accessible to gas and water supply lines. DO
NOT locate the water heater where water lines could be subjected to
freezing temperatures. Make sure the cold water pipes are not located
directly above the gas control so that condensate during humid weather
does not drip on the controls.
Installation (Locating The Water Heater) continued-
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Water heater corrosion and component failure can be caused by the heating and
breakdown of airborne chemical vapors. Examples of some typical compounds
that are potentially corrosive are: spray can propellants, cleaning solvents,
refrigerator and air conditioning refrigerants, swimming pool chemicals, calcium
and sodium chloride, waxes and process chemicals. These materials are
corrosive at very low concentration levels with little or no odor to reveal their
presence. NOTE: DAMAGE TO THE WATER HEATER CAUSED BY EXPOSURE
TO CORROSIVE VAPORS IS NOT COVERED BY THE WARRANTY. DO NOT
OPERATE THE WATER HEATER IF EXPOSURE HAS OR WILL OCCUR. DO
NOT STORE ANY POTENTIALLY CORROSIVE COMPOUNDS IN THE
VICINITY OF THE WATER HEATER.
WARNING
Liquefied petroleum gases/propane gas are heavier than air and
will remain at floor level if there is a leak. Basements, crawl
spaces, closets, and areas below ground levewill serve as
pockets for accumulation of leaking gas. Before lighting, smell
all around the appliance area for gas. Be sure to smell next to
the floor.
IF YOU SMELL GAS:
·
·
Do not try to light any appliance.
Do not touch any electc switch; do not use any telephone in
your building.
·
·
Immediately call yur gas supplier from a neighbor’s
telephone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire
department.
DO NOT OPERATE APPLIANCE UNTIL THE LEAKAGE IS
CORRECTED!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Locating The Water Heater) continued-
WARNING
DO NOT ATTEMPT TO LIGHT ANY GAS APPLIANCE IF YOU ARE NOT
CERTAIN OF THE FOLLOWING:
·
Liquefied petroleum gases/propane gas and natural gas have an
odorant added by the gas supplier that aids in the detection of the
gas.
·
·
Most people recognize this odor as a “sulfur” or “rotten egg” smell.
Other conditions, such as “odorant fade” can cause the odorant to
diminish in intensity, or ”fade”, and not be as readily detectable.
·
If you have a diminished sense of smell, or are in any way nsure of
the presence of gas, immediately contact your gas supplier from a
neighbor’s telephone.
·
Gas detectors are available. Contact your gas supplier, or plumbing
professional, for more information.
The water heater must be located close enough to the outside wall to keep the
venting distance within the maximum distance described in the installation
instructions. Read the venting section in this installation instruction manual
before locating the water heater.
This water heater must be located in an area where leakage of the tank or water
line connections and the combination temperature and pressure relief valve will
not result in damage to the area jacent to the water heater or to lower floors of
the structure. When such locations cannot be avoided, a suitable drain pan
adequately piped for propedrainage must be installed under the water heater.
The pan must not restrict combustion air flow. The drain pan must be no greater
than 1-½ inches (3.8 cm) deep and have a minimum length and width of at least
four (4) inches (10.2 cm) measured from the jacket of the water heater. The drain
pan, as described above, can be purchased from your plumbing professional.
The drain pan must be piped to an adequate drain. The piping must be at least
3/4 inch (1.9 cm) in diameter and pitched for proper drainage.
It is recommended that a minimum clearance of four (4) inches (10.2 cm) be
provided on the side of the water heater for servicing and maintenance of the
combination temperature and pressure relief valve.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Minimum Clearances) continued-
Minimum Clearances
WARNING
Failure to adhere to these installation and operating instructions may
create a hazard to life and property and will nullify the warranty.
This installation must allow access to the front of the water heater and adequate
clearance must be provided for servicing and operating this water heater. The
water heater may be installed on either a combustible or non-combustible floor. If
the water heater is to be installed directly on carpeting, it must be installed on
top of a metal or wood panel extending beyond the full width and deptof the
appliance by at least three (3) inches (7.6 cm) in any direction or, if the appliance
is to be installed in an alcove or closet, the entire floor must be covered by the
panel. The minimum clearances to combustibles for this water heater are: zero
(0) inch (0 cm) from the sides and rear, five (5) inches (12.7 cm) from the front of
the jacket, zero (0) inch (0 cm) from the vent connector and fifteen (15) inches
(38.1 cm) from the jacket top.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
This venting section is divided into two parts. Part I will cover venting
specifications for 48 Gal - 65,000 BTU (181.7 L - 19.1 kW/Hr), 65 Gal -65,000
BTU (246.1 L - 19.1 kW/Hr), and 75 Gal - 76,000 BTU (283.9 L - 22.3 kW/Hr)
models. Part II will cover venting specifications for 40 Gal -40,000 BTU
(151.4 L - 11.7 kW/Hr) and 48 gal - 40,000 BTU (181.7 L - 11.7 kW/Hr)
models. Refer to the rating plate located on the water heater for correct
model identification.
The Nation Fuel Gas Code ANSI Z223.1-(Latest Edition), CGA/CAN B149 Installation
Code, and local codes have specific requirements for the location of the vent terminals
on vertical walls. The guidelines listed below are from the National Fuel s Code.
Consult the local codes, and/or National Fuel Gas Code ANSI Z223.1-(Latest Edition),
or CGA/CAN B149 Installation Code to determine if there are any additions or changes
to the following specifications.
(A) The vent terminal must terminate at least 3 feet (.91 m) above any forced
air inlet duct located within 10 feet (3 m). Exception: This provision shall
not apply to the combustion air intake of a direct vent appliance.
(B) The vent terminal must terminate at least 4 feet (1.2m) below, 4 feet (1.2
m) horizontally from, or 1 foot (.31 m) abve any door, window, gravity air
inlet into the building.
(C) The bottom of the vent terminal mst be located at least 1 foot (.31 m)
above ground and above the anticipated snow level.
(D) The vent terminal must not terminate over a public walkway or over an
area where condensate or apor could create a nuisance or hazard or
could be detrimental to the operation of regulators, relief valve, or other
equipment.
(E) The water heater location must provide easy access for the entire length
of the vent connector.
(F) The vent system must be inspected at least once a year to ensure
against leakage of exhaust products.
Exceptions For Installations in Canada:
(A) The vent terminal must be located at least 1 foot (.31 m) from any window
or door which can be opened in any building, any non-mechanical air
supply inlet to any building, or the combustion air to any inlet other
appliance.
(B) The vent terminal must be located at least 6 feet (1.8 m) from any
mechanical air supply inlet to the building.
(C) The vent terminal must not terminate above a meter/regulator assembly
within 3 feet (.91 m) horizontally of the vertical centerline of the regulator
and must be at least 6 feet (1.8 m) from any gas service regulator vent
outlet.
(D) The vent terminal must be at least 7 feet (2.1 m) above a paved sidewalk
or a paved driveway located on public property.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
(E) The vent terminal must not terminate above a paved sidewalk or a paved
driveway which is located on private adjacent property.
Venting (Part I) continued-
Venting System Condensation
Condensate formation does not occur in all installations of power vented heaters,
but should be protected against on installations where condensation can form in
the venting system.
Formation of condensation in the venting system of Power Vented water heaters
is dependent upon installation conditions including, but not limited to:
ambient temperature and humidity of installation location;
ambient temperature and humidity of venting space;
vent distance and slope;
and product usage.
In order to effectively control condensate from adversely ffecting the mechanical
components of the water heater several methods may be employed:
1. For horizontal installations the vent pipe can be installed with a
downward slope (not less than 1/8" nor greater than ½” per foot
maximum) and away from the blower motor.
2. In order to prevent condensate from draining back into the blower (vertical
or horizontal runs), a fitting and drain hose is available as a condensate
trap kit (see Table 1 for service part numbers). The all rubber fitting with
drain outlet mounts directly to the blower motor outlet and is secured
with two hose clamps (one to the blower motor outlet and the other to the
vent connector). The plastic tubing is provided to drain any accumulated
condensate away from the water heater and to a suitable drain. The kit
comes complete with instructions for proper installation of the fitting.
Table 1
Model
Service Part
239-42742-00
239-42743-00
2” (5.1 cm) Blower Outlet (exhaust)
3” (7.6 cm) Blower Outlet (exhaust)
Venting (Part I) continued-
10
Download from Www.Somanuals.com. All Manuals Search And Download.
3. In order to prevent condensate from draining back into the blower (vertical
or horizontal runs), a drain tee and condensate trap can be installed in
the horizontal vent as close as practical to the blower vent connection
(see Figure 1). The condensate disposal tube should be installed to
drain any accumulated condensate away from the water heater and to a
suitable drain. The drain tee and condensate hose are not available from
Bradford White, but should be available through your local distributor.
Figure 1
Venting (Part I) continued-
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Part I - Venting Specifications for:
48 Gallon, 65,000 BTU input (181.7 L, 19.1 kW/Hr)
65 Gallon, 65,000 BTU input (246.1 L, 19.1 kW/Hr)
75 Gallon, 76,000 BTU input (283.9 L, 22.3 kW/Hr)
This water heater is a power vented appliance and is designed to vent its
products of combustion through 3” (7.6 cm) or 4” (10.2 cm) diameter Schedule 40
(solid or cellular core) PVC pipe to the outdoors. This water heater may be
either vented through the wall or vertically through the roof. Use a 3” (7.6 cm) to
4” (10.2 cm) reducer to connect to the vent outlet when using 4” (10.2 cm) PVC.
Apply PVC cement at PVC locations. Table 2 lists the maximum vent lengths for
this water heater using 3” (7.6 cm) PVC. If possible, locate the water eater so
that the venting length and number of elbows are kept to the minimum distance
necessary to reach the outside. If the installation requires venting lengths that
exceed the lengths listed for 3” (7.6 cm) PVC in Table 2, then use 4” (10.2 cm)
PVC for the vent connector. Table 3 lists the venting distances allowed with 4”
(10.2 cm) diameter PVC pipe. When venting with 4” (10.2 cm) PVC, use a 4”
(10.2 cm) to 3” (7.6 cm) reducer to exit through the building wall with 3” (7.6 cm)
PVC. Use the 3” (7.6 cm) vent terminal supplied with the water heater to
terminate on the outside of the building. If the length of 3” (7.6 cm) PVC needed
to go through the wall is greater than 14” (3.5 cm), use 4” (10.2 cm) to go
through the wall and reduce to 3” (7.6 cmPVC immediately after exiting the
outside wall. Refer to the venting illustrations on the following pages. Make sure
the vent pipe terminal elbow fitting is at least 1” (2.5 cm) away from the edge of
the wall.
TABLE 2 - VENT CONNECTOR LENGTHS
FOR 3” (7.6 cm) DIAMETER PVC
Terminating
# of 90° Elbows
(excluding vent
terminal)
Maximum
Length
Minimum
Length
Through the Wall
Through the Wall
Through the Wall
Through the Wall
1
2
3
4
40 ft (12.2 m)
35 ft (10.7 m)
30 ft (9.1 m)
25 ft (7.6 m)
2 ft (.6 m)
3 ft (.9 m)
5 ft (1.5 m)
8 ft (2.4 m)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
1
2
3
4
40 ft (12.2 m)
35 ft (10.7 m)
30 ft (9.1 m)
25 ft (7.6 m)
2 ft (.6 m)
3 ft (.9 m)
5 ft (1.5 m)
8 ft (2.4 m)
Venting (Part I) continued-
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 3 -VENT CONNECTOR LENGTHS
FOR 4” (10.2 cm) DIAMETER PVC
Terminating
# of 90° Elbows
(excluding vent
terminal)
Maximum
Length
Minimum
Length
Through the Wall
Through the Wall
Through the Wall
Through the Wall
Through the Wall
1
2
3
4
5
70 ft (21.3 m)
65 ft (19.8 m)
60 ft (18.3 m)
55 ft (16.8 m)
50 ft (15.3 m)
2 ft (.6 m)
3 ft (.9 m)
5 ft (1.5 m)
8 ft (2.4 m)
12 ft (3.6 m)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
Through the Roof
1
2
3
4
5
70 ft (21.3 m)
65 ft (19.8 m)
60 ft (18.3 m)
55 ft (16.8 m)
50 ft (15.3 m)
2 ft (.6 m)
3 ft (.9 m)
5 ft (1.5 m)
8 ft (2.4 m)
12 ft (3.6 m)
NOTE: When using 4” (10.2 cm) PVC, use a 4” (10.1 cm) to 3” (7.6 cm)
reducer and exit the building wall with 3” (7.6 cm) PVC using the 3” (7.6
cm) 90° vent terminal supplied. Two 45° elbows are equivalent to one 90°
elbow.
Figure 2
IMPORTANT
All of the Venting connections must be leak checked with a soap and
water solution upon initial start up of the water heater. Any leaks must
be repaired before continuing operation of the water heater.
NOTE: ABS or CPVC pipes may be substituted for PVC pipe. Do not mix
ABS and PVC pipe in the same installation.
Venting (Part I) continued-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
THROUGH THE WALL VENTING:
Cut a 3 1/2 in. (8.9 cm) diameter hole in the wall at the point where the vent
connector is going to pass through the wall. Use the proper cement to secure
the 90° vent terminal provided with the water heater to the vent connector. The
distance between the edge of the 90° vent terminal and the exterior wall (see
Figure 3) must be 1 in. (2.5 cm). Use the proper cement and assembly
procedures to secure the vent connector joints between the terminal and the
blower outlet. Provide support brackets for every 3 feet (.91 m) of horizontal vent.
Figure 3
Venting (Part I) continued-
THROUGH THE ROOF VENTING: (VERTICAL VENTING)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cut the necessary holes through the roof and ceiling and install the vent
connector as shown in Figure 4. Make sure that the installation meets the local
codes and/or The National Fuel Gas Code ANSI Z223.1 (Latest Edition) or
CGA/CAN B149 Installation Code.
Figure 4
NOTE: For installations requiring both horizontal and vertical runs, the
following rule must be followed: Total number of feet of straight pipe
(both horizontally and vertically) must not exceed the allowable length
listed in the “Through The Wall” section of the table for total number of
elbows used. Also: Total number of vertical feet of straight pipe must not
exceed the allowable length listed in the “Through The Roof” section of
the table for total number of elbows used. For angular rises in venting,
any angle that is greater than or equal to 45° from the horizontal should
be considered a vertical rise.
Venting (Part I) continued-
THROUGH THE WALL VENTING WITH LOW GROUND CLEARANCE:
15
Download from Www.Somanuals.com. All Manuals Search And Download.
When venting cannot exit through the wall at a height greater than or equal to 12”
(30.5 cm) above the ground, or anticipated snow level, the installation must be
modified as shown below (see Figure 5). Refer to Table 4 for maximum venting
lengths using 3” (7.6 cm) PVC or Table 5 for maximum lengths using 4” (10.2 cm)
PVC.
Figure 5
Venting (Part I) continued-
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 4
3” (7.6 cm) PVC VENT CONNECTOR LENGTHS FROM INSIDE WALL FOR
LOW GROUND CLEARANCE INSTALLATIONS
Terminating
# of
Elbows
Maximum
Length
Minimum
Length
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
1
2
3
4
30 ft (9.1 m)
25 ft (7.6 m)
20 ft (6.1 m)
15 ft (4.6 m)
5 ft (1.5 m)
6 ft (2 m)
8 ft (2.5 m)
10 ft (3 m)
TABLE 5
4” (10.2 cm) VENT CONNECTOR LENGTHS FROM INSIDE WAFOR
LOW GROUND CLEARANCE INSTALLATIONS
Terminating (Reduce 4” to 3”) #of
Maximum
Length
Minimum
Length
(Reduce 10.1 cm to 7.6 cm)
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
(2) 90° Elbows with (1) 90° Elbow
Elbows
1
2
3
4
5
60 ft (18.3 m) 10 ft (3 m)
55 ft (16.8 m) 12 ft (3.7 m)
50 ft (15.2 m) 15 ft (4.6 m)
45 ft (13.7 m) 18 ft (5.5 m)
40 ft (12.2 m) 22 ft (6.7 m)
HIGH ALTITUDE INSTALLATIONS FOR ELEVATIONS OVER 3,000
FEET (914.5 m) ABOVE SEA LEVEL
The capacity of the induced draft blower declines with increasing altitude due to a
reduction in the air density. In order to assure safe and reliable performance of
the water heater, the following guidelines must be followed. Refer to the venting
tables below for maximum distances for the altitudes in your location.
TABLE 6 - HIGH ALTITUDE LENGTHS
Altitude bove
sea level
Maximum
venting length venting length
reduction from reduction from
Maximum
Modifications to
water heater
tables 2 & 4
tables 3 & 5
0-3,000 ft
(0-914.5m)
No reduction in
vent length
required
No reduction in
vent length
required
None
over 3,000-
10,000 ft
(914.5-3048m)
No reduction in
vent length
required
No reduction in
vent length
required
Requires high
altitude kit. Call
the supplier or the
manufacturer
Venting (Part I) continued-
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Part II - Venting Specifications for:
40 Gallon, 40,000 BTU input (151.4 L, 11.7 kW/Hr)
48 Gallon, 40,000 BTU input (189.3 L, 11.7 kW/Hr)
This water heater is a power vented appliance and is designed to vent its
products of combustion through 2” (5.1 cm) or 3” (7.6 cm) diameter Schedule 40
(solid or cellular core) PVC pipe to the outdoors. The water heater may be either
vented through the wall or vertically through the roof. Use a 3” (7.6 cm) to 2” (5.1
cm) reducer to connect to the vent outlet when using 3” (7.6 cm) PVC. Apply
PVC cement at PVC locations. Table 7 lists the maximum vent lengths for ths
water heater using 2” (5.1 cm) PVC. If possible, locate the water heater so that
the venting length and number of elbows are kept to the minimum distance
necessary to reach the outside. If the installation requires venting lenhs that
exceed the lengths listed for 2” (5.1 cm) PVC in Table 7 then use 3” (7.6 cm)
PVC for the vent connector. Table 8 lists the venting distances allowed with 3”
(7.6 cm) diameter PVC pipe. When venting with 3” (7.6 cm) PVC, use a 3” (7.6
cm) to 2” (5.1 cm) reducer to exit through the building wall with 2” (5.1 cm) PVC.
Use the 2” (5.1 cm) vent terminal supplied with the water heater to terminate on
the outside of the building. If the length of the 2” (5.1 cm) needed to go through
the wall is greater than 14” (35.6 cm), use 3” (7.6 cm) PVC to go through the wall
and reduce to 2” (5.1 cm) PVC immediately after exiting the outside wall. Refer
to the venting illustrations on the following pges. Make sure the vent pipe
terminal is at least 1” (2.5 cm) away from e edge of the wall. To vent
horizontally with zero (0) elbows, remove 3 screws from blower housing
and rotate the blower housing 90° clockwise (see Figure 7). Replace the
three (3) screws once blower using rotation is complete.
TABLE 7- VENT CONNETOR LENGTHS FOR 2” (5.1cm) DIAMETER PVC
Terminating
# of 90° Elbows
(excluding vent
terminal)
Maximum
Length
Minimum
Length
Through the Wall
Through e Wall
Through the Wall
Through the Wall
Through the Wall
0
1
2
3
4
45 ft (13.7m)
40 ft (12.2m)
35 ft (10.7m)
30 ft (9.2 m)
25 ft (7.6 m)
2 ft (.6 m)
2 ft (.6 m)
2 ft (.6 m)
2 ft (.6 m)
3 ft (.9 m)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
Through the Roof
0
1
2
3
4
31 ft (9.5 m)
28 ft (8.5 m)
25 ft (7.6 m)
22 ft (6.7 m)
19 ft (5.8 m)
3 ft (.9 m)
3 ft (.9 m)
3 ft (.9 m)
3 ft (.9 m)
4 ft (1.2 m)
Venting (Part II) continued-
TABLE 8-VENT CONNECTOR LENGTHS FOR 3” (7.6 cm) DIAMETER PVC
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminating
# of 90° Elbows
(excluding vent
terminal)
Maximum
Length
Minimum
Length
Through the Wall
Through the Wall
Through the Wall
Through the Wall
Through the Wall
Through the Wall
0
1
2
3
4
5
105 ft (32.0 m)
100 ft (30.5 m)
95 ft (29.0 m)
90 ft (27.5 m)
85 ft (26.0 m)
80 ft (24.4 m)
10 ft (3.1 m)
10 ft (3.1 m)
10 ft (3.1 m)
10 ft (3.1 m)
10 ft (3.1 m)
10 ft (3.1 m)
Through the Roof
Through the Roof
Through the Roof
Through the Roof
Through the Roof
0
1
2
3
4
55 ft (16.8 m)
50 ft (15.3 m)
45 ft (13.7 m)
40 ft (12.2 m)
35 ft (10.7 m)
5 ft (1.5 m)
5 ft (1.5 m)
5 ft (1.5 m)
5 ft (1.5 m)
5 ft (1.5 m)
NOTE: When using 3” (7.6 cm) PVC, use a 3” (7.6 cm) to 2” (5.1 cm)
reducer and exit the building wall with 2” (5.1 cm) PVC using the 2” (5.1
cm) 45° vent terminal supplied. Two 45° elbows are equivalent to one 90°
elbow. Each 90° elbow is equivalent to 5 feet (1.5 m) of straight vent pipe.
Figure 6
IMPORTANT
All of the Venting connections must be leak checked with a soap and
water solution upon initial start up of the water heater. Any leaks must
be repaired before continuing operation of the water heater.
NOTE: ABS or CPVC pipes may be substituted for PVC pipe. Do not mix
ABS and PVC pipe in the same installation.
Venting (Part II) continued-
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7
THROUGH THE WALL VENTING:
Cut a 2 1/2 in. (6.4 cm) diameter hole in the wall at the point where the vent
connector is going to pass through the wall. Use the proper cement to secure
the 45° vent terminal provided with the water heater to the vent connector. The
distance between the edge of the 45° vent terminal and the exterior wall (see
Figure 8) must be at least 1 in. (2.5 cm). Use the proper cement and assembly
procedures to secure the vent connector joits between the terminal and the
blower outlet. Provide support brackets fevery 3 feet (.91 m) of horizontal vent.
Figure 8
Venting (Part II) continued-
20
Download from Www.Somanuals.com. All Manuals Search And Download.
THROUGH THE ROOF VENTING: (VERTICAL VENTING)
Cut the necessary holes through the roof and ceiling and install the vent
connector as shown in Figure 9. Make sure that the installation meets the local
codes and/or The National Fuel Gas Code ANSI Z223.1 (Latest Edition) or
CGA/CAN B149 Installation Code.
Figure 9
Venting (Part II) continued-
21
Download from Www.Somanuals.com. All Manuals Search And Download.
THROUGH THE WALL VENTING WITH LOW GROUND CLEARANCE:
When venting cannot exit through the wall at a height greater than or equal to 12”
(30.5 cm) from the ground or from the anticipated snow level, then the installation
must be modified as shown below (see Figure 10). Refer to Table 9 for maximum
venting lengths using 2” (5.1 cm) PVC or Table 10 for maximum lengths using 3”
(7.6 cm) PVC.
Figure 10
NOTE: For installations requiring both horizontal and vertical runs, the
following rule must be followed: Total number of feet of straight pipe
(both horizontally and vertically) must not exceed the allowable length
listed in the “Through The Wall” section of the table for total number of
elbows used. Also: Total number of vertical feet of straight pipe must not
exceed the allowable length listed in the “Through The Roof” section of
the table for total number of elbows used. For angular rises in venting,
any angle that is greater than or equal to 45° from the horizontal should
be considered a vertical rise.
Venting (Part II) continued-
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE 9
2” (5.1 cm) PVC VENT CONNECTOR LENGTHS FROM INSIDE WALL FOR
LOW GROUND CLEARANCE INSTALLATIONS
Terminating
# of
Elbows
0
Maximum
Length
35 ft (10.7
m)
Minimum
Length
2 ft (.6 m)
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
1
2
3
4
30 ft (9.2 m)
25 ft (7.6 m)
20 ft (6.1 m)
15 ft (4.6 m)
2 ft (.6 m)
2 ft (.6 m)
3 ft (.9 m)
4 ft (1.2 m)
TABLE 10
3” (7.6 cm) VENT CONNECTOR LENGTHS FROM INSIDE WALL FOR LOW
GROUND CLEARANCE INSTALLATIONS
Terminating (Reduce 3” to 2”) #of
Maximum
Lengh
90 ft (27.5 m) 10 ft (3.1 m)
85 ft (25.9 m) 10 ft (3.1 m)
80 ft (24.4 m) 10 ft (3.1 m)
75 ft (22.9m)
70 ft (21.4 m) 10 ft (3.1 m)
65 ft (19.8 m) 12 ft (3.7 m)
Minimum
Length
(Reduce 7.6 cm to 5.1 cm)
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
(2) 90° Elbows with Vent Terminal
Elbows
0
1
2
3
5
10 ft (3.1 m)
HIGH ALTITUDE INSTALLAIONS FOR ELEVATIONS OVER 2,000
FEET (610 m) ABOVE SEA LEVEL
The capacity of the induced draft blower declines with increasing altitude due to a
reduction in the air density. In order to assure safe and reliable performance of
the water heater, the following guidelines must be followed. Refer to the venting
tables below for maximum distances for the altitudes in your location.
TABLE 11 - HIGH ALTITUDE VENT CONNECTOR MODIFICATIONS
Altitude above sea
level
Maximum venting
length reduction
from tables 7 & 9
Maximum venting
length reduction from
tables 8 & 10
0 - 2,000 ft
(0 - 610 m)
No reduction in vent
length required
No reduction in vent
length required
over 2,000 - 5,000 ft
(over 610 - 1524 m)
over 5,000 - 8,000 ft
(over 1524 - 2439 m)
over 8,000 - 10,000 ft
(over 2439 - 2540 m)
Reduce maximum vent
length by 20 ft (6.1 m)
Use only 3” (7.6 cm)
PVC (Tables 8 & 10)
Use only 3” (7.6 cm)
PVC (Tables 8 & 10)
No reduction in vent
length required
No reduction in vent
length required
Reduce maximum vent
length by 20 ft (6.1 m)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Combustion Air Supply
WARNING
Liquefied petroleum gases/propane gas are heavier than air and will remain at
floor level if there is a leak. Basements, crawl spaces, closets and areas
below ground level will serve as pockets for accumulation of leaking gas.
Before lighting, smell all around the appliance area for gas. Be sure to smell
next to the floor.
IF YOU SMELL GAS:
·
·
Do not try to light any appliance.
Do not touch any electric switch; do not use any telephone in your
building.
·
·
Immediately call your gas supplier from a neighbor’s telephone. Follow the
gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
DO NOT OPERATE APPLIANCE UNTIL LEAKAGE IS CORRECTED!
IMPORTANT
The flow of combustion and ventilating air ust not be obstructed.
Provide adequate air for combustion and ventilation. An insufficient supply of air
will cause recirculation of combustion products resulting in air contamination that
may be hazardous to life. Such a condition often will result in a yellow, luminous
burner flame, causing carbon build up or sooting of the combustion chamber,
burners, and flue tubes with possible damage to the heater.
When an exhaust fan is installed in the same room with a heater, sufficient
openings for air must be provided in the walls. Undersized openings will cause
air to be drawn into the room through the chimney, causing recirculation of
combustion roducts.
Unconfined Spaces
In unconfined spaces in buildings, infiltration may be adequate to provide air for
combustion, ventilation, and dilution of flue gases. However, in buildings of tight
construction (for example, weather stripping, heavily insulated, caulked, vapor
barrier, etc.), additional air may need to be provided using the methods described
under CONFINED SPACES: All Air From Outdoors or Specially Engineered
Installations.
Confined Spaces
Confined spaces are spaces defined as having less than 50 ft.3/1000 BTU (1.4
m3/0.29 kw-hr).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Combustion Air Supply) continued-
All Air From Inside the Building: The confined space must be provided with
two permanent openings communicating directly with an additional room(s) of
sufficient volume so that the combined volume of all spaces meets the criteria for
an unconfined space. The total input of all gas utilization equipment installed in
the combined space must be considered in making this determination. Each
opening must have a minimum free area of 1 square inch per 1000 BTU (6.5
cm2/0.29 kw) per hour of the total input rating of all gas utilization equipment in
the confined space, but not less than 100 square inches (645 cm2). One opening
must be within 12 inches (31 cm) of the top and one within 12 inches (31 cm) of
the bottom of the enclosure.
All Air From Outdoors: The confined space must be provided with two
permanent openings, one commencing within 12 inches (31 cm) of the top and
one commencing within 12 inches (31 cm) from the bottom of the enclosure. The
openings must communicate directly, or by ducts, with the outdoors or spaces
(crawl or attic) that freely communicate with the outdoor.
1. When directly communicating with the outdoors, each opening must have a
minimum free area of 1 square inch per 4000 BTU (6.5 cm2/1.2 kw) per hour
of total input rating of all equipment in the enclosure.
2. When communicating with the outdoors through vertical ducts, each opening
must have a minimum free area of 1 square inch per 4000 BTU (6.5 cm2/1.2
kw) per hour of total input rating of all equipment in the enclosure.
3. When communicating with the outdoors through horizontal ducts, each
opening must have a minimum free area of 1 square inch per 2000 BTU (6.5
cm2/0.6 kw) per hour of total input rating of all equipment in the enclosure.
4. When ducts are used, they must be of the same cross-sectional area as the
free area of the openings to which they connect. The minimum dimension of
rectangular air ducts must be not less than 3 inches (7.5 cm).
Specially Engineered Installations
The requirements noted under CONFINED SPACES above must not necessarily
govern when special engineering, approved by the authority having jurisdiction,
provides an adequate supply of air for combustion, ventilation, and dilution of flue
gases.
Water Connections
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: BEFORE PROCEEDING WITH THE INSTALLATION, CLOSE THE MAIN
WATER SUPPLY VALVE.
After shutting off the main water supply, open a faucet to relieve the water line
pressure to prevent any water from leaking out of the pipes while making the
water connections to the water heater. After the pressure has been relieved,
close the faucet. The COLD water inlet and HOT water outlet are identified on the
top of the water heater. The fittings at the cold water inlet and hot water outlet
are dielectric waterway fittings with 3/4” NPT male thread. Make the proper
plumbing connections between the water heater and the plumbing system to the
house. Install a shut-off valve in the cold water supply line.
CAUTION
If sweat fittings are to be used DO NOT apply heat to the nipples on p of
the water heater. Sweat the tubing to the adapter before fitting the adapter to
the water connections. It is imperative that heat is not applied to the nipples
containing a plastic liner.
WARNING
FAILURE TO INSTALL AND MAINTAIN A NEW, LISTED 3/4” X 3/4”
TEMPERATURE AND PRESSURE RELIEF VLVE WILL RELEASE THE
MANUFACTURER FROM ANY CLAIM THAT MIGHT RESULT FROM
EXCESSIVE TEMPERATURE AND PRESSURES.
If this water heater is installed in a closed water supply system, such as one
having a back-flow preventer in tcold water supply, provisions must be made to
control thermal expansion. DO NOT operate this water heater in a closed
system without provisions fr controlling thermal expansion. Your water supplier
or local plumbing inspector should be contacted on how to control this situation
After installation of the water lines, open the main water supply valve and fill the
water heater. While the water heater is filling, open several hot water faucets to
allow air to escape from the water system. When a steady stream of water flows
through the faucets, close them and check all water connections for possible
leaks. NEVER OPERATE THE WATER HEATER WITHOUT FIRST BEING
CERTAIN IT IS FILLED WITH WATER.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
For protection against excessive temperatures and pressure, install temperature
and pressure protective equipment required by local codes, but not less than a
combination temperature and pressure relief valve certified by a nationally
recognized testing laboratory that maintains periodic inspection of production of
listed equipment or materials as meeting the requirements of the Standard for
Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply
Systems, ANS Z21.22 or the Standard CAN1-4.4. Temperature and Pressure
and the Standard CAN1-4.4, Temperature, Pressure, Temperature and Pressure
Relief Valves and Vacuum Relief Valves. The combination temperature and
pressure relief valve must be marked with a maximum set pressure nto
exceed the maximum working pressure of the water heater. The combination
temperature and pressure relief valve must also have an hourly rated temperature
steam BTU discharge capacity not less than the hourly rating of the water
heater.
Install the combination temperature and pressure relief valve into the opening
provided and marked for this purpose on the water heater.
Note: Some models may already be equiped or supplied with a combination
temperature and pressure relief valve. Vify that the combination temperature
and pressure relief valve complies with local codes. If the combination
temperature and pressure relief valve does not comply with local codes, replace
it with one that does. Follow thnstallation instructions above on this page.
Install a discharge line so tat water discharged from the combination
temperature and pressure relief valve will exit within six (6) inches (15.2 cm)
above, or any distance below the structural floor and cannot contact any live
electrical part. The discharge line is to be installed to allow for complete drainage
of both the combination temperature and pressure relief valve and the discharge
line. The discharge opening must not be subjected to blockage or freezing. DO
NOT thread, plug or cap the discharge line. It is recommended that a minimum
clearance of four (4) inches (10.2 cm) be provided on the side of the water heater
for servicing and maintenance of the combination temperature and pressure relief
valve.
Do not place a valve between the combination temperature and pressure relief
valve and the tank.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (Water Connections) continued-
WARNING
Hydrogen gas can be produced in an operating water heater that has
not had water drawn from the tank for a long period of time (generally
two weeks or more). Hydrogen gas is extremely flammable. To
prevent the possibility of injury under these conditions, we recommend
the hot water faucet to be open for several minutes at the kitchen sink
before you use any electrical appliance which is connected to the hot
water system. If hydrogen is present, there will be an unusual sound
such as air escaping through the pipes as hot water begins to flow. Do
not smoke or have open flame near the faucet at the time it is open.
This water heater can deliver scalding temperature water at any faucet in the
system. Be careful whenever using hot water to avoid scalding injury. Certain
appliances such as dishwashers and automatic clothes washers may require
increased temperature water. By setting the thermostaon this water heater to
obtain the increased temperature water required by these appliances, you may
create the potential for scald injury. To protect against injury, you should install
an ASSE approved mixing valve in the water system. This valve will reduce point
of discharge temperature by mixing cold and hot water in branch supply lines.
Such valves are available from the manufacturer of this water heater or a local
plumbing supplier. Please consult with a lumbing professional.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Connections
The gas supply lines must meet all requirements of the National Fuel Gas Code
ANSI Z223.1-(Latest Edition) and/or in Canada CAN/CGA B149 Installation
Codes - (Latest Editions).
The minimum permissible gas supply pressure for the purpose of input
adjustment is 1.5” water column (.37 kPa) above the operating manifold pressure
for natural gas and 1.0” (.25 kPa) water column for L.P. gas. See the rating plate
and combination gas control for the manifold pressure and gas type. The
maximum permissible gas supply pressure is 14.0” water column (3.5 kPa) for
natural gas and liquefied petroleum gases/propane gas.
1. Connect this water heater only to the type of gas (Natural or Propane gas) as
shown on the rating plate. Use clean 1/2 inch black iron pipe. (Dirt and scale
from the pipe can enter the combination control and cause it to malfunction).
The inlet gas line must have a minimum length of 3” (7.6 cm) drip leg
(sediment trap) installed as close to the water heate’s combination gas
control as possible. A ground joint union must be installed in the gas supply
line feeding the water heater to permit servicing of the water heater.
Compounds used on the threaded joints of he gas piping must be resistant
to the action of liquefied petroleum gases/propane gas.
2. This water heater and its gas connecton must be leak tested before placing
the water heater in operation. Check for gas leaks with a soap and water
solution and a brush or a commercial leak detector fluid. NEVER USE A
MATCH OR OPEN FLAME FOR TESTING!
3. While checking for leaks care must be taken to prevent solution from
contacting the electrical connections at the control. If electrical
connections at the control become wet, they must be thoroughly dried before
attempting to operate the water heater.
CAUTION
The water heater and individual shutoff valve must be disconnected from the
gas supply piping system during any pressure testing of the system at test
pressures in excess of 1/2 psi (3.5 kPa). The water heater must be
isolated from the gas supply piping system by closing its manual shutoff
valve during any pressure testing of the gas supply system at test
pressures equal to or less than 1/2 psi (3.5 kPa). The supply line must be
capped when not connected to the water heater.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections
All electrical wiring and connections must be in accordance with the National
Electric Code ANSI/NFPA No. 70 (latest edition), or the Canadian Electrical Code
C22.1 (latest edition) and any local codes which may apply. The water heater
must be electrically grounded.
If a flexible line cord and plug is permitted by local code, then provide a (3) three
wire grounding type receptacle within 6 feet (1.9 m) of the water heater and use
the flexible cord provided. Do not plug the line cord into a receptacle that can
have its power supply interrupted by a switch that is used to turn on and off
lights.
If wiring in conduit is required, remove the flexible line cord from the jacket and
install a 1/2" electrical conduit connector and connect 110/120 volt power source.
Connect the hot, neutral, and ground leads of the electrical supply to the
corresponding locations that were connected to the flexie line cord.
CAUTION
Turn off or disconnect the electrical power supply to the water heater before
servicing. Label all wires prior to disconnecion when servicing controls.
Wiring errors can cause improper and dgerous operation. Verify proper
operation after servicing.
The wiring diagram for the 48 gal, 65,000 BTU (181.7 L, 19.1 Kw/Hr), 65 gal,
65,000 BTU (246.1 L, 19.1 Kw/Hr) and 75 gal, 76,000 BTU input (283.9 L, 22.3
Kw/Hr) models is located in Figure 11 on page 31. The wiring diagram for
the 40 gal, 40,000 BTU (151.4 L, 11.7 Kw/Hr) and 48 gal, 40,000 BTU (181.7
L, 11.7 Kw/Hr) models are located in Figure 12 on page 32. Refer to the
rating plate located on the water heater for correct model identification.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections (Figure 11) continued-
Figure 11
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connections (Figure 12) continued-
Figure 12
32
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL OPERATION
WARNING
Water heaters are heat producing appliances. To avoid damage or injury
there must be no materials stored against the water heater or vent-air intake
system, and proper care must be taken to avoid unnecessary contact
(especially by children) with the water heater and vent-air intake system.
UNDER NO CIRCUMSTANCES MUST FLAMMABLE MATERIALS, SUCH
AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE
VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN
ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER
HEATER OR VENT-AIR INTAKE SYSTEM.
TO FILL THE WATER HEATER
1. Close the water heater drain valve by turning the stem clockwise.
2. Open the cold water supply shut-off valve.
3. Open several hot water faucets to allow air to escape from the system.
4. When a steady stream of water flows from the faucets, the water heater is
filled. Close the faucets and check for water leaks at the water heater drain
valve, combination temperature and pressurrelief valve and the hot and cold
water connections.
TO DRAIN THE WATER HEATER
Should it become necessary to completely drain the water heater, make sure you
follow the steps below:
1. Shut off the gas supply to the water heater.
2. Turn off/disconnect all lectric power to the water heater.
3. Close the cold water supply shut-off valve.
4. Open the drain valve on the water heater by turning the stem counter-
clockwise. The drain valve has threads on the end that will allow the
connection of a standard hose coupling.
5. Open a hot water faucet to allow air to enter the system.
To refill the water heater, refer to “To Fill the Water Heater.”
33
Download from Www.Somanuals.com. All Manuals Search And Download.
General Operation continued-
Lighting and shutdown instructions
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Thermostat Adjustment
CAUTION
Before adjusting thermostat(s), turn off power supply to the water heater.
The thermostat dial is adjusted to approximately 120°F when shipped from the
factory. When adjusting the thermostat, it should be remembered that lower
temperature settings are more energy efficient. The thermostat cover, on the
right side of the gas valve, must be removed when the thermostat is adjusted. To
adjust the thermostat turn the dial clockwise with a screwdriver until the minimum
acceptable temperature is set. It is suggested that the starting point setting not
exceed the 120°F (49°C) or “HOT” setting on the thermostat.
Figure 13
DANGER
Hotter water increases the risk of scald injury. Scalding may occur within five
(5) seconds at a temperature setting of 135°F (57.3°C). To protect against hot
water injury, install an ASSE approved mixing valve in the water system. This
valve will reduce point of discharge water temperatures by mixing cold and hot
water in branch water lines. A licensed plumbing professional or local
plumbing authority should be consulted.
Note: This water heater is equipped with an energy cut out device to prevent
overheating. Should overheating occur, turn off the electrical supply to the
water heater and contact a qualified service technician.
Burner Flame Check
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Cast Iron Burner: At the time of installation and at periodic intervals (not more
than 6 months), a visual check of the main burner and pilot flames should be
made to determine if they are burning properly. For ideal operation, the gas and
air must be properly proportioned. The proper air-gas mixture is obtained by
adjusting the air shutter on the mixer face of the main burner (See Figure 14). To
adjust for proper burning, loosen the air shutter nut (if provided), rotate shutter to
close the opening in the burner then slowly rotate the shutter until the yellow tips
disappear and the flame becomes blue. On 75 gallon models fired on LPG or
propane, adjust the air shutter as described above until the yellow flame is
minimized (note-the burner flame may contain a mixture of yellow and blue).
Tighten the air shutter nut (if provided). Too much air will cause the flame to lift
off the burner ports and create noisy operation. Too little air will resuln soot
formation. The main burner flame should light smoothly from the pilot.
Steel Burner: These models are equipped with self adjusting air mixture and do
not have an adjustable air shutter (See Figure 14). At periodic intervals a visual
check of the main burner and pilot flames should be mae to determine if they
are burning properly. The main burner flame should light smoothly from the pilot.
Figure 14
MAINTENANCE
36
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Water heaters are heat producing appliances. To avoid damage or injury there
must be no materials stored against the water heater or vent-air intake
system, and proper care must be taken to avoid unnecessary contact
(especially by children) with the water heater and vent-air intake system.
UNDER NO CIRCUMSTANCES MUST FLAMMABLE MATERIALS, SUCH
AS GASOLINE OR PAINT THINNER BE USED OR STORED IN THE
VICINITY OF THIS WATER HEATER, VENT-AIR INTAKE SYSTEM OR IN
ANY LOCATION FROM WHICH FUMES COULD REACH THE WATER
HEATER OR VENT-AIR INTAKE SYSTEM.
IMPORTANT
The water heater should be inspected at a minimum annually by a
qualified service technician for damaged components and/or joints not
sealed. DO NOT operate this water heater if any part is found
damaged or if any joint is found not sealed.
The following maintenance should be performed by a qualified service technician
at the minimum periodic intervals suggested below. In some installations, the
maintenance interval may be more frequent depending on the amount of use and
the operating conditions of the water heater. Regular inspection and
maintenance of the water heater and vent-air intake system will help to insure
safe and reliable operation.
1. Annually check the operation of the thermostat.
2. The flow of combustion and ventilation air MUST NOT be restricted. Clear
the combustion air openings of any dirt, dust, or other restrictions.
WARNING! The ventilation air system may be HOT.
3. At all times keep the water heater area clear and free from combustible
materials, gasoline and other flammable vapors and liquids.
4. Bi-annually conduct a visual check of the main and pilot burner flames to
determine that they are burning properly. See Burner Flame Check section
on page 36. If sooting or other burner anomalies are evident, shut down the
water heater by turning off the gas per the instructions listed in this manual or
as listed on the water heater.
Maintenance continued-
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Annually remove the inner door and main burner assembly to clean orifices
and related parts of any dirt or other foreign material. Inspect the burner
ports for obstructions or debris and clean with a wire brush as needed. Wire
brush and/or vacuum clean the combustion chamber as needed to remove
scale deposits and debris. NOTE: It is imperative for proper operation of the
water heater that the inner door be replaced in the original location.
WARNING
When lifting lever of the combination temperature and pressure relief
valve, hot water will be released under pressure. Be careful that any
released water does not result in bodily injury or property daage.
7. At least once a year, check the combination temperature and pressure relief
valve to insure that the valve has not become encrusted with lime. Lift the
lever at the top of the valve several times until the valve seats properly without
leaking and operates freely.
8. Monthly drain off a gallon of water to remove silt and sediment.
WARNING! THIS WATER MAY BE HOT.
9. If the combination temperature and psure relief valve on the appliance
discharges periodically, this may be due to thermal expansion in a closed
water supply system. Contact the water supplier or local plumbing inspector
on how to correct this situati. Do not plug the combination
temperature and pressure relief valve outlet.
10. A combination sacrificial anode rod/hot water outlet nipple has been installed
to extend tank life. The anode rod should be inspected periodically (every 2
years) and replaced when necessary to prolong tank life. Water conditions in
your area will influence the time interval for inspection and replacement of the
anode rod. Contact the plumbing professional who installed the water heater
or the manufacturer listed on the rating plate for anode replacement
information. The use of a water softener may increase the speed of anode
consumption. More frequent inspection of the anode is needed when using
softened (or phosphate treated) water.
11. The induced draft blower has sealed motor bearings and does not require
adding oil.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance (continued)-
CAUTION
FOR YOUR SAFETY. DO NOT ATTEMPT REPAIR OF COMBINATION GAS
CONTROL, BURNERS OR GAS PIPING. REFER REPAIRS TO A
QUALIFIED SERVICE TECHNICIAN.
Contact your supplier or plumbing professional for replacement parts or contact
the company at the address given on the rating plate of the water heater.
Provide the part name, model and serial numbers of the water heater when
ordering parts.
READ THE WARRANTY FOR A FULL EXPLANATION OF THE LENGTH OF
TIME THAT PARTS AND THE WATER HEATER ARE WARRANTED.
Manufactured under one or more of the following U.S. atents: RE. 34,534;
B1 5,341,770; 4,416,222; 4,628,184; 4,669,448; 4,672,919; 4,808,356;
4,829,983; 4,861,968; 4,904,428; 5,000,893; 5,023,031; 5,052,346;
5,081,696; 5,092,519; 5,115,767; 5,199,385; 5,277,171; 5,372,185;
5,485,879; 5,574,822; 5,596,952; 5,660,165; 5,682,666; 5,943,984;
5,954,942; 5,988,117; 6,142,216. Other U.S. and Foreign patents
applications pending.
Current Canadian Patents: 1,272,914; 1,280,043; 1,289,832; 2,045,862;
2,107,012; 2,108,186; 2,112,515.
Complete the following information and retain for future reference:
Model No:
Serial No:
Service Phoe
Days:
Nights:
Address:
Supplier:
Supplier Phone No:
39
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST DRAWING
PARTS LIST
PART NAME AND DESCRIPTION
1. Blower Assembly
2. Temperature Switch
3. Pressure Switch
4. Flue Baffle
5. Honeywell Smart Valve
6. Drain Valve
11. Diptube – Nipple
12. Anode – Nipple
13. Thermostat (Behind Cover)
14. T & P Relief Valve Opening
15. Pilot Assembly
16. Cast Iron Burner
7. Fiberglass Insulation
8. Foam Insulation
9. Outer Door
17. Main Burner Orifice
18. Gas Feedline
19. Air Shutter (Cast Iron Only)
20. Steel Burner
10. Thermostat Cover
40
Download from Www.Somanuals.com. All Manuals Search And Download.
THE FOLLOWING INSTRUCTIONS ARE FOR INSTALLATION OF:
GAS WATER HEATERS SUITABLE FOR WATER (POTABLE)
HEATING AND SPACE HEATING
1. All piping components connected to this water heater for space heating
applications must be suitable for use with potable water. In Massachusetts,
space heating piping length must not exceed 50 feet.
2. Toxic chemicals, such as those used for boiler treatment, must not be
introduced into potable water used for space heating.
3. This water heater must not be connected to an existing heating system or
component(s) previously used with a non-potable water heating appliance.
4. When the system requires water for space heating at temperatures higher
than required for other means, such as an ASSE approved mixing alve must
be installed to temper the water for those uses in order to reduce the scald
hazard potential.
Please refer to the illustration below for the suggested piping arrangement.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
VENT PIPE PREPARATION AND JOINING
Most failures in PVC, CPVC or ABS systems result from improper preparation
and joining of pipe and fittings. The guidelines below must be followed when
installing the venting system. If you have any question about the application or
installation of the PVC, CPVC or ABS venting system, contact the manufacturer,
supplier, or your plumbing professional.
1) Specific cleaners, solvents, primers and cements are available for PVC,
CPVC and ABS pipe. Be sure these materials match the type of pipe to be
installed. Never use all-purpose cements, commercial glues and adhesives
or ABS cement to join PVC or CPVC pipe and fittings.
a) CLEANERS, SOLVENTS, PRIMERS AND CEMENTS ARE
FLAMMABLE. Do not store or use these materials near heat or
open flame, or in the vicinity of other appliances.
2) Use proper cutting, deburring and applicator tools to ensure proper
preparation and joining of pipe and fittings.
a) Cutting Tools
i) A square cut must be achieved with a miter box saw or pipe cutter to
ensure a proper mating with the female. If a pipe cutter is used, the
burr created at the outer edge of thpipe must be removed.
b) Deburring Tools
i) A file, knife or plastic deburring tool can be used to remove burrs.
Burrs must be removed from the inside and outside edges of the pipe
to ensure a proper seal.
c) Applicator Tools
i) A pure bristle paintbrush or roller may be used to apply cement.
Prompt application of the cement is important due its fast drying
properties.
3) Inspection, Cleaning, Priming and Cementing
a) Inspect the pipe inside and out for dirt, dust, moisture or grease etc.
Check ppe and fittings for splits or cracks and replace if necessary.
b) Clean pipe and fittings are imperative for proper joining. Following
cuttig and deburring, wipe away any foreign material with a clean dry
rag. If wiping fails to thoroughly clean surfaces, chemical cleaning is
necessary.
c) Primer must be applied to the pipe surface and fitting socket with a
natural bristle brush. This serves to soften and prepare the PVC or
CPVC for cementing.
Vent Pipe Preparation and Joining (continued)-
42
Download from Www.Somanuals.com. All Manuals Search And Download.
d) Cementing must be done quickly to avoid over-drying before joining.
i) Apply one coat to the outside end of the pipe at a width slightly
greater than the depth of the socket.
ii) Apply a coat around the inside of the fitting socket.
iii) Apply a second coat around the end of the pipe.
4) Joining
a) Joints should be made immediately after cement is applied.
b) After fully inserting pipe into fitting socket, give pipe about ¼ turn to help
spread cement evenly. Hold joint together for about 15 to 20 seconds.
c) Remove excess cement from around pipe and fitting with a clean rag.
d) Cement drying times may vary. Be sure to allow for the recommended
drying time before disturbing joints.
For more specific and detailed information about the above, contact the
manufacturer, supplier, or competent professional.
NOTES
43
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
|