User’s Manual
648UA
IN-DASH SINGLE-DIN
MP3-COMPATIBLE CD
AM/FM RECEIVER
WITH USB AND SD MEMORY CARD PORTS
AND FRONT PANEL AUX INPUT
648UA
IN-DASH SINGLE-DIN MP3-COMPATIBLE
CD AM/FM RECEIVER
WITH USB AND SD MEMORY CARD PORTS
AND FRONT PANEL AUX INPUT
0113
BOSS Audio Systems
3451 Lunar Court • Oxnard, CA 93030
iPod® is a trademark of Apple, Inc.
registered in the U.S. and other countries.
Boss Audio Systems is not affiliated with Apple, Inc.
800.999.1236
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRES CONNECTION
LOCATION AND FUNCTION OF CONTROLS
RCA OUTPUT
WHITE
RCA OUTPUT
RED
2
3
4
17
5
648UA
6
7
MODE
/
PTY
BAND
APS
/
ISO SOCKET
ANTENNA JACK
ISO SOCKET SKETCH
CONNECTOR B
1
2 INT
3 RPT
4 RDM
5
6
CONNECTOR A
1.
1. Rear Right Speaker (+)
2. Rear Right Speaker (-)
3. Front Right Speaker (+)
4. Front Right Speaker (-)
5. Front Left Speaker (+)
6. Front Left Speaker (-)
7. Rear Left Speaker (+)
8. Rear Left Speaker (-)
18
15
1
8
9
10
11
12
13
14
16
2.
3.
4. Memory +12V
5. Auto Antenna Output
6.
7. 12V (To Ignition Key)
8. GROUND
SPECIFICATION
GENERAL
Supply Voltage
Current Consumption
Power Output
Number of channels
Unit Dimensions
DC 12 V. Negative Ground
Max.10A
4 x 60 W
2 STEREO channels.
(L x W x H): 7” x 6.5” x 1.97”
178 x 165 x 50 (mm)
1. RELEASE BUTTON
Press the REL button to release the front control panel from the unit chassis,
then pull it up a little to remove from the unit chassis.
2.POWER ON/OFF & MUTE
When the unit is power off, the unit switches on by pressing any button except
the EJECT and the RELEASE button.
FM SECTION
Frequency range
87.5Mhz - 108Mhz
(Europe)
87.5 Mhz - 107.9Mhz (U.S.A.)
3uV.
10.7MHz.
When the unit is power on, press and hold the power button for more than 0.5
seconds, the unit goes into power off mode.
When the unit is power on, press the power to switch the MUTE state on/off.
Effective sensitivity
I.F Frequency
AM SECTION
Frequency range
3. CD SLOT
522Khz - 1620Khz
530khz - 1710Khz
40dB.
(Europe)
(U.S.A.)
Effective sensitivity
I.F Frequency
4. LCD Display
450KHz
5.EJECT KEY
Preamp Output
1 V Output
In the power on state, the loaded disc can be ejected by pressing the EJ key.
CD PLAYER
System
Suitable CDs
Frequency characteristics
6&7. TUNE, SEEK, TRACK, SKIP UP / DOWN BUTTONS
a) During RADIO mode:
MP3 Audio System.
MP3, CD,CD-R,CD-RW Disc
20Hz-100Hz < 5dB
10KHz-20KHz < 5dB.
50dB [1KHz]
Press the >>| or |<< button briefly to manual tune up/down for the desired radio
station frequency step by step.
Press and hold the >>| or |<< button for longer 0.5 seconds, to automatically
tune up/down for the radio station frequency of strong signal.
S/N Ratio to CD
Page 2
Page9
b) During disc, USB playback mode:
CARE FOR USING CD'S:
Press the >>| button briefly to play next track.
Press the |<< button briefly to play the current track from the beginning of it
if the playing time is more than 2 seconds.
Press the |<< button briefly to play the previous track if the playing time is
less than 2 seconds.
About CD-R/CD-R/W discs:
In addition to commercially-recorded audio CD's, this unit can play CD-R and
CD-R/W discs. In some cases, particularly when recorded on older CD burners,
some CD-R and CD-R/W discs may not play. Also, whenever you are recording
a CD for playback in this receiver, it is recommended that you record at 24x or
slower speed for CD-R and 4x or slower for CD-R/W to achieve higher signal
quality and better playback performance.
Press the >>| or |<< button and hold to skip forwards or backwards, release
to resume normal playback.
8.SEL(MENU) BUTTON AND VOLUME UP ( + )/ DN ( - ) KONB
a) Press the SEL button briefly, it is activated as selecting each mode of E. VOL.
-> VOLUME ->BASS ->TREBLE -> BALANCE -> FADER ->
When selecting a desired audio mode, rotate the VOL knob to adjust the
audio effect.
In each mode, the waiting time is about 5 seconds, and when the waiting time
is over, it returns to the last display mode of tuner or CD mode.
The control mode of E.VOL is operated with following numeric display.
- VOL: (MIN)00, 01,......46, 47(MAX).
1. To keep the disc clean:
Do not attach any sticker or adhesive tape on the disc.
Handle the disc by its edge to keep the disc clean and do not touch the surface.
Before playing a disc, wipe it off with a clean, dust-free cleaning cloth.
Wipe the disc outwards from the disc center.
2. When one has already been inserted. Doing so may damage the unit. Insert a disc
with labeled surface up, or it will damage the unit.
- BASS/TRE: -07, -06,...,00,...+06,+07
- BAL: 0LR9, 1LR9, ..., 9LR9,..., 9LR1, 9LR0
- FAD: 0FR9,1FR9, ..., 9FR9,..., 9FR1, 9FR0
3. Do not expose the disc to direct sunlight or nearby heat sources such as heating
vents, caliduct which can cause the disc to warp.
b) When pressed longer 2 seconds, it show the time then it is activated as
cyclical mode of following functions for user’s selection.
->TA(ON/OFF) -> AF(ON/OFF) -> TA (ALARM/SEEK) ->PI (SOUND/MUTE)
->RETUNE (LONG/SHORT)->MASK(DPI/ALL) ->BEEP (ON/OFF)
-> USER SET(FLAT/CLASSIC/ROCK/POP)->VOL(LAST/DEFA)
-> EUROPE/AMERICA(in radio mode) ->MONO/STEREO(only for FM mode)
->LOUD(ON/OFF) ->LOCAL/DX(only for FM mode) ->CLK(ON/OFF)
Do not leave disc in a car if it is parked in direct sunlight as that will lead to a
considerable rise in the temperature inside the car.
4. Do not use any secondhand or rented disc, usually, there is glue on the surface of
those discs, it will stop the unit working and damage it.
5. Always store the disc in its case for protection. Scratched up discs will produce poor
sound performance and cause CD player to skip.
you can adjust HOUR or MINUTE by rotating
->CLK(12/24)mode->CLK 00’00(
the VOL knob).
After selecting the desired mode, rotate the VOL knob to select one setup
item of the desired mode.
6. In raining day or wet area, the moisture may form on the disc or the optical parts,
the playback may not be possible. If moisture forms on the disc, wipe it off with a
soft cloth.
1) TA [TRAFFIC ANNOUNCEMENT]
When TA mode is on(TA is displayed on LCD), it will begin to seek TA station
and TA SEEK will be displayed on LCD for a while.
If moisture forms on the optical parts of the unit, allow the unit to sit for about one
hour with power on.
When traffic announcement is transmitted:
7. Do not use solvents such as benzine or thinners. Commercially available cleaners
or anti-static spray will damage the unit.
(1)If the unit is in USB or disc mode, it will switch to radio mode temporarily.
Temporarily switch over to an EON linked station when EON detects a traffic
announcement on that other program, and TP will be displayed on LCD
(2)If volume level is below 20, volume level is raised to 20, and returns to its
previous mode and volume level when the traffic announcement is over.
(3)If volume is adjusted during traffic announcement, only the traffic
announcement volume is valid.
* TA interruption function:
The current traffic announcement is cancelled by pressing this key. But the
TA mode will not be off.
When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or
saved only when traffic program identification code has been received.
*
Page 8
Page 3
2) AF [ALTERNATIVE FREQUENCIES]
20. SD CARD SLOT
When you need to play the file in the SD card, insert the SD card into the
SD card slot. The system will change into the SD mode automatically,
and then play the first file in the SD.
When AF switching mode is selected and the state of AF switching mode is
displayed by AF segment in display.
Segment off: AF switching mode off.
Note:
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not
received yet.
When SD card and USB stick are both inserted into their slot or socket, the
system will change into the playback mode of the latter one.
When AF switching mode is selected, the radio checks the signal strength of
AF all the time. The interval of checking time of each AFs depends on the
signal strength of current station, from a few minute for strong station to a few
seconds for weak station. Every time that new AF is stronger than current
station, it switches over to that frequency for very short time, and
NEW FREQUENCY is displayed for 1-2 seconds. Because the mute time of AF
switching or checking time is very short, it is almost inaudible in case of
normal program.
INSTALLATION METHOD
This is an anti-theft installation method.
The main unit wears a METAL MOUNTING SLEEVE.
Please connect the wiring, eg, the Power supply, the Speakers and the Antenna
according to the requirements of this Instruction Manual, then install the metal mounting
sleeve into the car as per the diagram illustrated below.
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can
only receive and save RDS program.
To properly fix the metal mounting
sleeve, bend the tabs of the sleeve
against the DASH BOARD with a
screwdriver.
To raise the anti-skip capability of the unit,
please ensure the metal support strap is
connected firmly to the car chassis.
3) TA SEEK/TA ALARM:
METAL
SUPPORT STRAP
TA SEEK mode: when newly tuned station does not receive TP information for
5 seconds, the radio retunes to next station which has a different PI to the last
station, but has the TP information.
When TP information gets lost at the current station for retune time which is
set by RETUNE SHORT(60 seconds) or RETUNE LONG(90 seconds), the
radio starts to retune to next same PI station. When same PI station does not
receive in 1 cyclic search, the radio retunes to next station with TP information.
TA ALARM mode: when this mode is selected, any automatic retune mode is
not activated. Only double beep sound(ALARM) will be heard.
When newly tuned station does not have TP information for 5 seconds, beeps
are sounded.
UNIT CHASSIS
PLASTIC TRIM RING
DASHBOARD
METAL MOUNTING SLEEVE
FRONT PANEL
To remove the CD player out of the mounting sleeve,
insert the two supplied keys into the left and right side
slots of the chassis at the same time.
When TP information gets lost at the current station for retune time, the beep
sound will be heard.
When newly tuned station has no RDS signal, PI SEEK is suppressed .
4) PI SOUND/ PI MUTE:
NOTE
PI SOUND mode: if a car cruises between buildings that could cause
reflecting signals, a phenomenon may occur, due to different PI codes being
received from the same AF source. when different PI sounds (DIP) are heard
occassionally, this will happen for less than 1 second.
PI MUTE mode: under above same situation, a mute sound will be heard for
less than1second.
Remove the two screws that protect
the CD player during transportation
before operating the player.
Before installing and operating
the CD player, remove the metal
mounting sleeve illustrated by
the arrows.
To attach the removable faceplate, insert the
right side of the faceplate into the right of the
CD player chassis first. Then push the left side
of the faceplate into the chassis until you hear
it “click”.
5) RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not received for retune interval , the radio starts to
retune to next same PI station.
When same PI station does not receive 1 cyclic search, the radio goes to last
station and waits for 4-5 minutes until PI code is received.
RETUNE L mode: selected as 90 seconds.
RETUNE S mode: selected as 60 seconds.
Page 4
Page 7
In Radio mode, Press MODE/PTY button longer to select one of the following
mode: POP M- - NEWS
While selecting PTY TYPE, its selection is implemented by preset buttons as
described in preset key. (press one of the 6 preset buttons shortly and repeatedly
to select the PTY TYPE in the preset button)
6) MASK DPI/MASK ALL:
MASK DPI mode: masks only the AF which has different PI.
MASK ALL mode: masks the AF which has different PI and NO RDS signal
with high field strength.
When POP M or NEWS is on, the previous PTY program and PTY word is
displayed on LCD.
If there are no keys entered for 2 seconds, previously selected PTY is searched.
During 1 loop, if desired PTY is not found, NO PTY is flashed, then return to
previous normal radio and PTY icon goes off.
7)BEEP ON/BEEP OFF
BEEP ON mode: The beep is generated when any key is pressed.
BEEP OFF mode: The beep sound is disabled..
8) VOL LAST/VOL DEFA
VOL LAST: The radio switches on at the actual volume it had when it was last
16.AUX INPUT JACK
switched off.
Press the mode button to select auxiliary input playing mode. Then you can
connect any matched external audio device to this socket. Use the volume
knob to adjust volume.
VOL DEFA: After pressing SEL button, AVOL will be displayed. Then you can
pre-select a constant switch-on volume by using the VOL knob.
9)CLK ON/OFF
17.USB SOCKET
CLK ON: Clock will always show on the display when power off.
CLK OFF: Clock will disappear on the display when power off.
In order to play the file in the USB stick, turn over the plastic cover cap then
insert the USB stick into the USB socket. The system will change into the
USB mode automatically, and then play the first file in the USB.
9-14. PRESET STATION MEMORY AND TOP/>||, INT, RPT, RDM BUTTONS
a) During radio mode:
Go to any preset station by pressing one of the 6 preset station buttons (1-6).
If one of these buttons is pressed for more than 2 seconds, the station
currently being listened to will be memorized into the selected preset button.
b) During disc, SD or USB mode:
1) Press the TOP/ >|| button briefly to interrupt the playback of the disc, SD
or USB. Press again to resume normal playback of the disc, SD or USB.
Press the TOP/>|| button and hold for approximately 0.5 seconds to play the
first track of the disc, SD or USB.
2) Press the INT button to sample the first 10 seconds part of each track, and the
INT ON will be visible on the LCD display.
18. BAND/APS BUTTON
During radio mode:
1)Press this button briefly to select the radio broadcasting band you would
like to hear. The AM/FM band is toggled cyclically through the tuning bands:
->FM 1-> FM 2 -> FM 3 ->AM1(MW 1)->AM2(MW 2) ->.
2) Press and hold for more than 1 second, the radio searches from the current
frequency and checks the signal strength level until 6 stations are found.
And then the 6 stations frequency are preset to the corresponding preset
memory numbered bank. The auto-storage operation is implemented in the
each selected band. When the auto-storage operation is finished, the radio
execute the Preset Scan.
In the process of INT, pressINT button again to stop sampling and to continue
playing the current track, and the LCD will display INT OFF.
3) Press the RPT button once to play the current track repeatedly, and the RPT
ONE will be visible on the LCD display.
Note: when AF OFF, it only need to use 20s to store ; while AF ON as it needs to take
time to search for RDS signal, if more radio stations, it takes more time, especially
if more non-RDS radio station, more time it searches.
During MP3/WMA disc, SD or USB mode, press the RPT button twice
continuously to play the current folder repeatedly, and the RPT DIR will be
visible on the LCD display.
In the process of RPT, press RPT button again to stop playing repeatedly
mode and the LCD will display RPT OFF.
During MP3 file in disc, or USB mode:
Press this button to turn to TRACK SEARCH mode, the LCD will display TRK
000 and flash the biggest digit 0 that the USB stick contain. (if the number of
tracks is less than 100 and more than 9, it will be TRK 00)
Then rotate the VOL knob to select the number of the flashing digit from 0 ~ 9.
Then press SEL button to confirm the number and flash next smaller digit 0.
With the same means, select the number of the flashing digit. After finishing
selecting the number of all flashing digit, press SEL button to play the track of
the selected serial number.
4) Press the RDM button to play all tracks on disc in random order, and the RDM
ON will be visible on the LCD display.
In the process of RDM, press RDM button again to stop playing in random
order and the LCD will display RDM OFF.
5) Press the 5 and 6 button to move up and down10 tracks at a time.
When the remaining total tracks are less than10, both buttons are inactive.
Press and hold the 5 and 6 button to select next or previous folder to be played.
19. RESET BUTTON
Before operating the unit for the first time, or after replacing the car battery or
changing the connections. You must reset the unit.
Press the reset button with a paper clip or pen. This operation will erase the clock
setting and some stored content.
15. MODE AND PTY (PROGRAM TYPE) BUTTON
Press the MODE button to change among tuner (radio), disc (when a disc is
loaded), USB (when an USB stick is inserted) and AUX mode.
Page 6
Page 5
PDF created with FinePrint pdfFactory trial version hDttopw:n/l/owadwfrowm.Wpdwwff.Saocmtaonruyal.sc.coomm. All Manuals Search And Download.
|